Professional Documents
Culture Documents
ETL-41 SYSTEM
TECHNICAL SPECIFICATIONS
FOR
Page 1 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
1. All the drawings, i.e. elevation, side view, plan, cross sectional
view etc., in AutoCAD format and manuals in PDF format, for
offered item shall be submitted. Also the hard copies as per
specification shall be submitted.
3. The bidder shall have to submit all the required type test reports for
the offered item. In case of non-submission of the type test reports
with the offer, the bid shall be liable to be rejected.
4. The bidder must fill up all the point of GTP for offered item/s.
Instead of indicating refer drawing, or as per IS/IEC, the exact
value/s must be filled in.
5. All the points other than GTP, which are asked to confirm in
technical specifications must be submitted separately with the bid.
7. Please note that the evaluation will be carried out on the strength of
content of bid only. No further correspondence will be made.
8. The bidder shall bring out all the technical deviation/s only at the
specified annexure.
9. The bidder should indicate manufacturing capacity by submitting latest
updated certificate of a Chartered Engineer (CE).
Page 2 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
Page 3 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
(I) GENERAL :
(IV) SPECIFICATION :
Page 4 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
All the equipments details as above shall fit into different tiers of
the "Swinging Frame" fitted inside the above cubicle, swinging
frame shall be of 14 SWG sheet steel.
The cubicle shall be made from 16 SWG sheet steel. It will have
rounded corners with front door and lock. It will be designed for
efficient cooling with an exhaust fan at the top inside the cabinet, to
take away the heat generated within the terminal. Normally the
cable entry shall be from the bottom, however, suitable provision
Page 5 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
shall be made for cable entry from top, which shall be covered by
blanking plate at the time of supply. Visual indication shall be
provided in front of the terminal at the top for indication of failure
of carrier terminal i.e. Transmitter, Receiver or Power supply.
There shall be provision for audio indication also. Suitable labels
for identification of indication shall be provided.
The cubicle shall be provided with foundation holes for fixing the
same on foundation. Air inlet shall be provided at bottom and Air
Outlet with exhaust fan at the top. Any opening shall be provided
with wire mesh for vermin proofing. The cubicle shall be
completely dust proof and vermin proof.
The cubicle size shall generally match with existing cubicle and
shall be of size 1960mm X 670 mm X 420 mm (Height x Width x
Depth). It shall be provided with standard 19" tiers to house the
modules.
Page 6 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
Page 7 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
All the test points with standard values, indications etc. shall be
provided in front of the cabinet and shall be easily accessible.
Page 8 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
The equipment must have gone through all environmental and field
tests and shall work satisfactorily under hot, humid and polluted
climate. It should have worked for at least five years successfully
in Electricity Boards. It shall work satisfactorily up to 55 C. It
shall satisfy a storage temperature of 70 C. The Temperature
criteria shall be shown by laboratory test by using hot chamber
during inspection.
Page 9 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
(IV)(B)
(V) CONFIGURATION:
Page 10 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
Valid type test reports not older than 5 Years and shall be valid
up to expiry of validity of offer for following tests along with
all test results sheets & reference documents shall be submitted
with the offer with List of Type Tests in Performa- X given here
under.
Performa X:
Page 11 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
(VII) DRAWINGS:
Page 12 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
S C H E D U L E "A"
SCHEDULE OF GENERAL TECHNICAL DATA AND
GUARANTEED TECHNICAL PERTICULARS
( TO BE FURNISHED BY THE BIDDER FOR CARRIER TERMINAL)
Sr. SYSTEM PARTICULAR TECHNICAL
No. PARTICULAR OF
BIDDER'S EQUIPMENT
1. Name of OEM
2. Type/Model
3. Operating Mode
4. HF Band
5. Nominal Bandwidth
6. Send / Receive Band
7. Permissible line attenuation
8. Frequency spacing for parallel
Working on a common line
9. HF System Impedance
10. Carrier Frequency Stability
11. Useful AF Bandwidth
12. Frequency Response
13. Linearity
14. Non - Linear Distortion
15. Near and Far End Crosstalk
16. Crosstalk Attenuation (Double channel)
17. Group delay
18. Basic Noise
19. Audio Frequency difference
Transmit to receive
20. Supervision alarms
21. Alarm Outputs
22. Ambient Conditions:
(a) For guaranteed data
(b) For reliable operation
(c) Storage
Page 13 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
S C H E D U L E "A"
SCHEDULE OF GENERAL TECHNICAL DATA AND
GUARANTEED TECHNICAL PERTICULARS
( TO BE FURNISHED BY THE BIDDER FOR CARRIER TERMINAL)
Sr. SYSTEM PARTICULAR TECHNICAL
No. PARTICULAR OF
BIDDER'S EQUIPMENT
23. Transmitter Data
(a) HF Output Power
(b) Harmonic and Spurious Signal
Attenuation
(c) Pilot channel with Programmable
range of Frequency
(d) Speech Input: 2 Wire
4 Wire
(e) Limiter Characteristics
(f) Suppression of unwanted Side bands.
24. Telephone Criteria
(a) Signaling
(b) Transit / Terminal Switching (V)
(c) Hybrid Switching (GA)
(d) 4 - Wire remote / emergency Call
telephone
25. Teleoperation Signals:
(A) Teleoperation I/P's
(a) Number & type of I/P
(b) Number of I/P with
Boosting Facility.
(c) Nominal I/P level.
(d) I/P level range
(e) Balance referred to
ground
(f) Return loss
(g) Minimum level for
maximum RF output
power.
(h) Boosting criteria.
Page 14 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
S C H E D U L E "A"
SCHEDULE OF GENERAL TECHNICAL DATA AND
GUARANTEED TECHNICAL PERTICULARS
( TO BE FURNISHED BY THE BIDDER FOR CARRIER TERMINAL)
Sr. SYSTEM PARTICULAR TECHNICAL
No. PARTICULAR OF
BIDDER'S EQUIPMENT
(B) Teleoperation O/P's
(a) Number & type of O/P's
(b) Nominal O/P level
(c) O/P level range
(d) Maximum O/P level (PEP)
(e) Balance referred to ground
(f) Return loss
Whether teleoperation I/P's & O/P's
expandable by inserting additional interface
module.
Whether provision is made for Programmable
Digital transit Filter, which allow to pass
required Band & frequencies of Teleoperation
Signal.
26. Receiver Data
(a) HF Sensitivity at coax input and at
Relative system impedance (speech) :
Carrier Frequency
(b) Selectivity :
From 4 kHz Carrier Band
(c) Image rejection
(d) IF rejection
(e) Automatic gain control:
AF Output Level
Time constant for 10 dB level
variation
(f) Hunting characteristics :
Synchronizing channel bandwidth
With loss of synch. signal
(auxiliary carrier)
Synchronization time with
loss of signal for 1 second:
Describe the method of
synchronization
Page 15 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
S C H E D U L E "A"
SCHEDULE OF GENERAL TECHNICAL DATA AND
GUARANTEED TECHNICAL PERTICULARS
( TO BE FURNISHED BY THE BIDDER FOR CARRIER TERMINAL)
Sr. SYSTEM PARTICULAR TECHNICAL
No. PARTICULAR OF
BIDDER'S EQUIPMENT
(g) Frequency response equalization
(h) Describe the method of Equalization
(i) Speech outputs:
2 wire
4 wire
Symmetry against ground
return loss
DC source resistance
(j) Signaling criteria :
(k) Pulse distortion :
(l) Squelch :
27. POWER SUPPLIES
(a) Mains
(b) Consumption
(c) Battery
(d) Consumption
(e) Reflected noise
28. TEST EQUIPMENT
(A) Test Tone generator : Test Tone
(B) Audio Tests :
(a) Band width
(b) Level range
(c) Input impedance
(d) Dummy load / test loop
(Whether print required for loop test is
provided)
(C) Any other test equipments required.
29. Insulation test and EMC:
(A) Unbalanced Carrier I/O
(a) impulse voltage test
(b) HF interference test
(c) Fast electrical transients/bursts
Page 16 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
S C H E D U L E "A"
SCHEDULE OF GENERAL TECHNICAL DATA AND
GUARANTEED TECHNICAL PERTICULARS
( TO BE FURNISHED BY THE BIDDER FOR CARRIER TERMINAL)
Sr. SYSTEM PARTICULAR TECHNICAL
No. PARTICULAR OF
BIDDER'S EQUIPMENT
(B) Balanced Carrier I/O
(a) Voltage withstand
(b) Insulation resistance
(c) Impulse voltage test
(d) HF interference test
(e) Fast electrical transients/burst
FREQUENCY SPACING required for
operation of carrier Terminal on a common
line:
(a) Transmitting Band to Own
Receiving Band :
(b) Transmitting Band to neighboring
Transmitting Band :
(c) Transmitting Band to neighboring
Receiving Band :
(d) Receiving Band to neighboring
Receiving Band :
Page 17 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
S C H E D U L E ' A/1
(To be filled in and signed by the Tenderer)
___________________________________________________________
Signature :
Date :
Place:
Page 18 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012
SUPPLY OF PLCC TERMINAL WITH
ETL-41 SYSTEM
Page 19 of 19
GETCO/E/TS-PLCC 03402/R1, Dt: 28.09.2012