Professional Documents
Culture Documents
41.In case of Al alloy tubing which of the following material is used for instrument
lines.
42.In case of Al alloy tubing which of the following material is used for hydraulic
&pneumatic systems.
i)Titanium is 30% stronger than steel. ii)Titanium is 50% lighter than steel
45. . In case otuf 1100 Al alloy tubing, to identify the material which of the following
colour code is used at
46. . In case of 3003 Al alloy tubing, to identify the material which of the following
colour code is used at both ends of tube.
47. In case of 5052 Al alloy tubing, to identify the material which of the following
colour code is used at both ends of tube.
48. . In case of 7075 Al alloy tubing, to identify the material which of the following
colour code is used at both ends of tube.
i)If the code markings are impossible to read it may be necessary to test
samples of material for hardenss.
ii)Reject the fluid line for repair iii) both iv) NOTA.
50. which of the following is a measurement method for O.D of metal tubing.
MH QUESTION BANK
51. which of the following is a painting method for coulour codes to identify Al alloy
tubing .
ii)painting should be not more than 4 in width. iii)both i &ii are needed iv)NOTA
53. which of the following should be maintained after cutting the metal tube,as a
standard maintenance practice.
i)Should produce a square end ii)should be free of burrs iii) )both i &ii
i) metal tubing should be cut 10% extra length, longer than the tube to
be replaced.
ii) metal tubing should be cut in exact length as the length of Replacetube.
iii)Both iv)NOTA
56.Which of the following is practically true method for using a tube cutter.
ii)Rotate the cutter around the tubing applying light pressure to the cutting wheel.
I)By using file. ii)by emerry paper iii)by using knife or deburring edge
attached to the tube cutter.
58. which of the following is a disadvantage for tube flaring during deburring the
tubing.
i)wall thickness reduction at the end of tubing . ii)fractured end during cutting or
deburring.
59.If cutter is not available at working place or maintenance facility ,which of the
following will be a best tool for cutting metal tubing .
i)Fine tooth hacksaw with 32 T.P.I. ii) Fine tooth hacksaw with 18 T.P.I
60. Which of the following dia of metal tubing can be bent by hand without
bending tool .
62.During bending of metal tubing ,which of the following defects should be taken
intoaccount.
i)Smaller dia. of flattened portion must not be less than 75% of original
O.D.
ii) Smaller dia. of flattened portion must not be more than 75% of original O.D.
66. Which of the following is an alternative bending method in case of metal tubing.
iv)ATA
67.which of the following kinds of flaring are used in a/c metal tubing.
68.At what angle ,the male &female dies ground ,for a/c tubing flaring.
71. in case of double flaring,Which of the following are advantages over the single
flare
i)To hold the metal tubing . ii)To centre the flaring pin over the end
of the tube.
73.There are how many types of flaring tools ,to make the flares and what are they,
75. which of the following metal tubing type is used for double flaring only.
76. . In case of which of the following Dia. of metal tubing hand beading tool can
be used.
SUBJECTIVE QUESTIONS:---
7.Explain in detail about procedure of identifying the colour codes over the metal
tubing including colour of each individual AL alloy in a table.
8. Explain in detail about cutting and bending procedure of metal tubings including
their types of bending defects.
9.explain in detail about metal tube cutter, tube bender,witha neat diagram.
10. explain in detail about the metal tube flaring tool and flaring procedure with
diagram.
11.write a note about flexible hose materials and their uses with diff.types of fluids.
MH QUESTION BANK