Professional Documents
Culture Documents
Seals and protects asphalt pavements Acronite treated substrates, following full cure, will
against premature ageing. accept road marking systems.
Acronite_Page 1
CyTech International
Product Data Sheet
ACRONITE
Cold-applied ashpalt pavement sealer and preservative
APPLICATION LIMITATIONS
Acronite is normally applied by distributor tank Do not apply to wet, coal tar, epoxy or other non-
spray truck, hand sprayers or for smaller areas asphalt surfaces.
rollers and squeegees.
STORAGE AND SHELF LIFE
Acronite maybe applied when ambient temperature
is above 1C. 12 months in original supply unopened drums.
Ensure that spray patterns overlap to avoid stripes Store under warehouse conditions if possible, away
on the pavement. from direct sunlight.
PACKAGING
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Acronite_Page 2
CyTech International
Product Data Sheet
BITUMEN BINDER PEN GRADE 85/100
Paving Grade Bitumen.
CyTech 85/100 is a pavement grade bitumen Principle hazard severe thermal burns.
produced to ASTM and AASHTO standards.
(See Attached Safe Handling of Bitumen Instruction
SUPPLY Sheet. )
SPECIFICATION COMPLIANCE
Min.Range Max.Range
Softening Point 45 52
Solubility in
trichlorethylene 99
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
DESCRIPTION
USES
APPLICATION
STORAGE
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cut Back_Bitumen__Page 1
CyTech International
Product Data Sheet
CYRO PRIME (S)
Solvent based Bitumen Primer [BLACK BITUMEN PAINT - D41]
Cyro Prime is a blend of high penetration grade In accordance with specification requirements
bitumen with less boiling range hydrocarbon otherwise, an application rate of 1 lit/m2 will result
solvents. It is generally used as all-purpose in a DFT of 0.55MM.
bituminous primer on steel and concrete, prior to
the application of protective coatings. TECHNICAL SUMMARY
1 Visosity @ 25C (saybolt furol) = 25- 125 S Solids Content : 55.0% min.
Specific Gravity : 0.88 approx.
2 Distillation - by volume % Colour (Wet) : Black.
Upto 225C = 35 mins. Colour (Dry) : Black.
Upto 360C = 65 max.
STORAGE
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoCoat PEE is a two-component solvent free liquid Long term corrosion protection.
epoxy resin modified with refined coal tar pitch. The
superior adhesion and chemical resistance of the PACKAGING
epoxy resin, in combination with the flexibility and
water resistance qualities of pitch produce a system CytoCoat PEE is supplied in 10 litre units.
that will provide a high build, ultra dense coating
to protect concrete, other cementitious substrates, TYPICAL PROPERTIES
and metal, against a wide range of aggressive
media. The coating will not support the growth of Pot life : 25C 1 Hour
bacteria. In appearance, CytoCoat PEE is smooth, 40C 20mins.
glossy and black. Tack free time : 25C 12 hours
40C 5 hours
TYPICAL APPLICATIONS Initial cure : Within 24 hours at
25C
CytoCoat PEE is used to provide a heavy duty Full chemical resistance : 7 days at 25C
protective, waterproof, and flexible coating. Uses
include, the lining of tanks, pipes and ducting, STANDARDS
coating concrete, asbestos cement, steel pipes and
non ferrous metals. ANSI/ASTM:C881: Type III: Grade 2:
Class C.
CytoCoat PEE is particularly suitable for use in BS 5493
sewerage work applications and in offshore or
marine environments. DIRECTIONS FOR USE
Cytocoat Pee_Page 1
CyTech International
Product Data Sheet
CYTOCOAT PEE
A two component solvent free pitch extended epoxy resin coating system.
APPLICATION Brine
Effluent
CytoCoat PEE can be applied by brush short hair Barnacle growth
roller or airless spray. A fast setting spray grade Sewage
version CytoCoat PEE is available for twin feed Exhaust gases
airless apray in 400ltr (2x200ltr) bulk packing. Marine bacteria
Diluted acids and alkalis
BRUSH/ROLLER APPLICATIONS Salt solutions (Potassium, Sodium)
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytocoat Pee_Page 2
CyTech International
Product Data Sheet
CYTOCRETE
Hot applied, high performance permanent concrete pavement repair system.
Minimum airport and highway The properties of CytoCrete are such that repairs
disruption. from 40mm up to full depth of the slab construction
can be carried out.
Ensures permanent repairs.
CytoCrete is available in three grades to ensure
Environmentally friendly. optimum performance.
Can be trafficked by airport traffic within CytoCrete will accommodate all normal movements
60 minutes of application. associated with concrete pavements; therefore
standard Joints may be bridged where CytoCrete
High compressive resistance. crosses these areas.
CytoCrete is part of the unique CyTech CytoCrete Type and form : Single component, hot applied
flexible concrete repair system, which has been Colour : Grey or Black
developed to meet the demands of increasingly Cure type : Thermo-set
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytocrete_Page 1
CyTech International
Product Data Sheet
CYTOCRETE
Hot applied, high performance permanent concrete pavement repair system.
MAINTENANCE
APPLICATION INSTRUCTIONS
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytocrete_Page 2
CyTech International
Product Data Sheet
CYTOFLEX 800
Liquid applied single component elastomeric waterproofing membrane.
Thermal stability. Moss and lichen must be removed and area treated
with proprietary fungicidal wash to kill spores and
Excellent adhesion. inhibit further growth. Following treatment wash
area thoroughly with clean water and allow to dry.
Can be applied to a range of Fillets must be provided at corners or sharp angles
substrates. using 4:1 sand and cement mortar modified with a
good quality bonding agent.
Outstanding resistance to oxidation and
brittlement. PRIMING
Cytoflex_800_Page 1
CyTech International
Product Data Sheet
CYTOFLEX 800
Liquid applied single component elastomeric waterproofing membrane.
CLEANING
COVERAGE
PACKAGING
20 litre pails.
CyTech International CyTech International
STORAGE AND SHELF LIFE Downsview house P.O. Box 20437
Little London Ajman Free Zone
East Sussex, TN21 0BB Gate No. 4, Ajman, U.A.E.
CytoFlex 800 should be stored in warehouse United Kingdom Tel: +971 (6) 7407121
conditions away from direct sunlight and sources Tel: +44 (0) 1435 813647 Fax: +971 (6) 7408794
Fax: +44 (0) 1435 813667 E-mail: info@cyrusgroup.ae
of ignition. E-mail: info@cyrusglobal.com www.cyrusglobal.com
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoflex_800_Page 2
CyTech International
Product Data Sheet
CYTOFLEX B4505
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
DESCRIPTION Drying Times : 6-8hours per coat @
25C.
CytoFlex B4505 is suitable for the treatment Appearance : Dark black/brown
of concrete, asphalt, metal, roofing felt and Coating. Cures to a
other similar roofing surfaces whether flat, Hard tack free finish.
sloping or vertical. Where added protection Chemical resistance : Water, aqueous
is required on roofs, CytoFlex B4505 may be groundwater, salt
used in conjuction with a reinforcing fabric. Solutions, mild
detergents,
TYPICAL APPLICATIONS acids and Alkalis.
TYPICAL PROPERTIES For slate roofs or where the roof is in poor condition,
a reinforcing membrane should be incorporated
Solids content : 45%. into the coating. Carry out surface preparation as
Rubber Content : 5% above and apply the first coat of CytoFlex B4505.
Specific gravity : 1.10 @ 25C Whilst still wet, bed in the reinforcing fabric brushing
Service Temp : -100C to +85C in well to ensure good adhesion. Adjacent areas
Flashpoint : N/A of membrane should overlap by 75mm.
CytoFlex_B_4505_Page 1
CyTech International
Product Data Sheet
CYTOFLEX B4505
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
After the fabric has been well bedded in, apply
a second coat of CytoFlex B4505. Apply two
further coats of CytoFlex B4505 ensuring the
previous coat is fully dry prior to subsequent
applications. Clean tools with water whilst wet.
When dry, white spirit or paraffin should be used.
COVERAGE RATES
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoFlex_B_4505_Page 2
CyTech International
Product Data Sheet
CYTOFLEX B4505
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
DESCRIPTION Drying Times : 6-8hours per coat @
25C.
CytoFlex B4505 is suitable for the treatment Appearance : Dark black/brown
of concrete, asphalt, metal, roofing felt and Coating. Cures to a
other similar roofing surfaces whether flat, Hard tack free finish.
sloping or vertical. Where added protection Chemical resistance : Water, aqueous
is required on roofs, CytoFlex B4505 may be groundwater, salt
used in conjuction with a reinforcing fabric. Solutions, mild
detergents,
TYPICAL APPLICATIONS acids and Alkalis.
TYPICAL PROPERTIES For slate roofs or where the roof is in poor condition,
a reinforcing membrane should be incorporated
Solids content : 45%. into the coating. Carry out surface preparation as
Rubber Content : 5% above and apply the first coat of CytoFlex B4505.
Specific gravity : 1.10 @ 25C Whilst still wet, bed in the reinforcing fabric brushing
Service Temp : -100C to +85C in well to ensure good adhesion. Adjacent areas
Flashpoint : N/A of membrane should overlap by 75mm.
CytoFlex_B_4505_Page 1
CyTech International
Product Data Sheet
CYTOFLEX B4505
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
After the fabric has been well bedded in, apply
a second coat of CytoFlex B4505. Apply two
further coats of CytoFlex B4505 ensuring the
previous coat is fully dry prior to subsequent
applications. Clean tools with water whilst wet.
When dry, white spirit or paraffin should be used.
COVERAGE RATES
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoFlex_B_4505_Page 2
CyTech International
Product Data Sheet
CYTOFLEX B6010
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
DESCRIPTION
Service Temp : -100C to +85C
CytoFlex B6010 is suitable for the treatment Flashpoint : N/A
of concrete, asphalt, metal, roofing felt and Drying Times : 6-8hours per coat
other similar roofing surfaces whether flat, @25C.
sloping or vertical. Where added protection Appearance : Dark black/brown
is required on roofs, CytoFlex B6010 may be Coating. Cures to a
used in conjuction with a reinforcing fabric. Hard tack free finish.
Chemical resistance : Water, aqueous
TYPICAL APPLICATIONS groundwater, salt
Solutions, mild
General waterproofing and damp proofing of detergents, acids
concrete, asbestos cement sheets, roofing felts, and Alkalis.
wood etc.
DIRECTIONS FOR USE
Protection of steelwork, pipes and metal.
Surface preparation:
ADVANTAGES Surfaces to which CytoFlex B6010 is to be applied
must be clean and free of dirt, dust, rust or any
Vapour Permeable allows substrate to other material which may impair adhesion. Where
breathe. moss or lichen is present, remove sheets. Cut
and reseal blisters in asphalt or roofing. Remove
Reduced chloride penetration due to chippings other than those that form the surface of
hard impermeable surfaces. mineralised felt.
Simple and easy to use, no skilled Old concrete and steel must be structurally sound
labour required. prior to application.
CytoFlex_B6010_Page 1
CyTech International
Product Data Sheet
CYTOFLEX B6010
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
Whilst still wet, bed in the reinforcing fabric brushing
in well to ensure good adhesion. Adjacent areas
of membrane should overlap by 75mm. After the
fabric has been well bedded in, apply a second
coat of CytoFlex B6010. Apply two further coats
of CytoFlex B6010 ensuring the previous coat is
fully dry prior to subsequent applications. Clean
tools with water whilst wet. When dry, white spirit
or paraffin should be used.
COVERAGE RATES
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoFlex_B6010_Page 2
CyTech International
Product Data Sheet
CYTOFLEX - MEM
CytoFlex-MEM is a seamless joint free cast-in situ hot applied flexible membrane system for the waterproofing
of concrete structures.
USES APPLICATION
CytoFlex-MEM can be used for the water proofing of CytoFlex-MEM is hot applied with squeegee in two
concrete Roof decks Basements, Balconies planters, layers with reinforcement in between the layers.
parking buildings, Foundations & retaining walls, The thickness recommended is 4-5mm average.
tunnels etc.intended to protect for zero leakages.
CLEANING
ADVANTAGES
All tools, equipment and splashes should be
Seamless & Joint free cast - in-situ cleaned using any suitable solvents Kerosene or
system. white spirit may also be used.
Personal hygiene is maintained with soap and
Solvent free 100% solids eco friendly. water.
Storage & performance stability. 15 Kgs Cartons with poly bag or metal drums.
Cytoflex_MEM_Page 1
CyTech International
Product Data Sheet
CYTOFLEX - MEM
CytoFlex-MEM is a seamless joint free cast-in situ hot applied flexible membrane system for the waterproofing
of concrete structures.
PRECAUTIONS
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoflex_MEM_Page 2
CyTech International
Product Data Sheet
CYTOFLEX-RBE
A rubberised bitumen emulsion for waterproofing and protective coating applications.
Resistant to chloride and sulphate Priming is not normally required on good quality,
attack. well prepared substrates.
Cytoflex_RBE_Page 1
CyTech International
Product Data Sheet
CYTOFLEX-RBE
A rubberised bitumen emulsion for waterproofing and protective coating applications.
COVERAGE
PACKAGING
PRECAUTIONS
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoflex_RBE_Page 2
CyTech International
Product Data Sheet
CYTOGRIP BT
Cold applied high friction surfacing system.
Cytogrip_BT_Page 1
CyTech International
Product Data Sheet
CYTOGRIP BT
Cold applied high friction surfacing system.
CytoGrip BT is supplied as two resin components. CytoGrip BT System should not be applied at
The part B should be poured completely into the temperatures below 5C or above 45C. Minimum
part A and the two resin components should be substrate and air temperature should be 5C and rising
mixed using a slow speed drill with a suitable with no expected rain during laying and cure period.
paddle for approximately 5 minutes. It is essential
that the two components are thoroughly mixed. REGIONAL GRADES
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytogrip_BT_Page 2
CyTech International
Product Data Sheet
CYTOJOINT
High performance asphaltic plug type bridge joint system.
Cytojoint_Page 1
CyTech International
Product Data Sheet
CYTOJOINT
High performance asphaltic plug type bridge joint system.
Movement accommodation for standard width Aluminium strip or steel plate as specified is placed
and depth of seal installed at mean joint width is over the expansion joint.
total +/- 25mm (50mm). With decreased depth,
movement capability is also reduced. Aggregate is pre-heated to 150C - 190C and
placed into the joint to a maximum depth of 40mm
Joints to be sealed should not exceed 45 skew and but not less than 20mm.
on areas of skew, CytoJoint width must not exceed
750mm. The layer is then flooded with the correctly heated
binder and the process is repeated until the joint is
Vertical movement accommodation of CytoJoint within 25mm of the surface.
is a maximum of 1 mm and where possible
longitudinal seals should be avoided. For final 25mm layer apply pre-mix layer and
compact using a compactor or vibrating roller.
4% gradient is the maximum recommended.
In situations where gradients in excess of this Seal surface using CytoJoint binder only.
figure is envisaged, please refer to Technical
Services Department. CYTOJOINT BINDER SELECTION TABLE
Cytojoint_Page 2
CyTech International
Product Data Sheet
CYTOJOINT
High performance asphaltic plug type bridge joint system.
NOTES
PACKAGING
PRECAUTIONS
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytojoint_Page 3
CyTech International
Product Data Sheet
CYTOMIX C1
Corrosion Inhibiting Concrete admixture.
Cytomix C1_Cal_Nit_Page 1
CyTech International
Product Data Sheet
CYTOMIX C1
Corrosion Inhibiting Concrete admixture.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytomix C1_Cal_Nit_Page 2
CyTech International
Product Data Sheet
CYTOMORTAR
High strength, non-flow, epoxy bedding and repair mortar.
For surface repairs of fine cracks and spalls. For gap COMPOSITION
filling, grouting, bedding fixtures etc. For repairs to
arises without the use of form work. Wherever a Two component epoxy-based mortar filled with
thixotropic epoxy mortar is required. selected fine aggregate.
CytoMortar_Page 1
CyTech International
Product Data Sheet
CYTOMORTAR
High strength, non-flow, epoxy bedding and repair mortar.
alkalis, diluted acids, sulphur gases, mineral, Failure to comply with the recommended storage
vegetable and animal oils and fats, ammonia and conditions may result in premature deterioration of
formaldehyde. the product or packaging.
APPLICATION PROCEDURE
Preparation:
All loose particles, laitance, dust and grease etc.,
must be removed prior to application of CytoMortar
1758.
Mixing:
The 3 kg pack has been designed to be readily
mixed by trowel. Where more than one pack is to
be mixed at a time, a Mixal portable mixer (HD5
model) is suitable.
Application:
Knife or trowel CytoMortar 1758 to the required
using the minimum of solvent on the trowel to aid
workability. The surface may be finished smooth by
use of a paint brush dipped in CLEANING SOLVENT
NO.2. Where a very deep recess is to be filled, it
may be necessary to build up in layers. Repairs may
be camouflaged if required by covering surface
with cement powder full cure is affected.
Working Temperature:
CytoMortar will cure at temperatures as low as 0C,
although at low temperatures cure is retarted.
COVERAGE
EQUIPMENT CARE
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoMortar_Page 2
CyTech International
Product Data Sheet
CYTOPATCH
Cold lay first time reinstatement asphalt repair compound.
Cytopatch_Page 1
CyTech International
Product Data Sheet
CYTOPATCH
Cold lay first time reinstatement asphalt repair compound.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytopatch_Page 2
CyTech International
Product Data Sheet
CYTOPAVE RR
Polymer modified bituminous, recessed repair compound.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytopave_RR_Page 1
CyTech International
Product Data Sheet
CYTOPAVE RR
Polymer modified bituminous, recessed repair compound.
It is recommended that the repair is dressed Avoid inhalation of fumes during heating process.
whilst still hot with clean, dust free, pre CytoPave
heated (to 120C) 2-4mm aggregate to give In order to avoid burns exercise extreme caution
anti-skid properties. when handling hot material.
Following cooling of the repair the area should Heatproof gloves, goggles, and overalls must
be swept by mechanical means to remove excess always be used.
aggregate dressing.
If contact with skin occurs seek medical advice
CLEANING immediately.
Application equipment should be thoroughly Refer to Materials Safety Data Sheet for further
cleaned out after use. Spillages should be information.
absorbed with sand or vermiculite etc. and be
disposed of in accordance with local regulations. FIRE
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytopave_RR_Page 2
CyTech International
Product Data Sheet
CYTOPAVE RR
Polymer modified bituminous, recessed repair compound.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytopave_RR_Page 3
CyTech International
Product Data Sheet
CYTOPAVE RS
Polymer modified bituminous, pavement crack sealer.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytopave_RS_Page 1
CyTech International
Product Data Sheet
CYTOPAVE RS
Polymer modified bituminous, pavement crack sealer.
APPLICATION PRECAUTIONS
PACKAGING
ESTIMATING
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytopave_RS_Page 2
CyTech International
Product Data Sheet
CYTOPROOF 60
Bitumen emulsion protective coating.
CytoProof 60 complies with concrete curing Where the CytoProof 60 is to take a screed, the
requirements of ASTM C309-93 when applied second coat should be blinded with clean, dry sharp
at the rate 2m2 per litre and to BAS6949l1991 sand as soon as applied. The excess sand should
requirements for bituminous coating. be brushed off when the coating has dried.
DESCRIPTION Cleaning
CytoProof 60 should be removed from tools and
CytoProof 60 is a brown/black liquid blend of equipment with water when it is wet. On drying
selected bitumens emulsified with water to give an CytoProof 60 may be removed using solvents.
easily applied protective coating.
ESTIMATING
PROPERTIES
Supply:
The essential properties of CytoProof 60 are:- CytoProof 60 : 200 Litre drums.
Cytoproof 60_Page 1
CyTech International
Product Data Sheet
CYTOPROOF 60
Bitumen emulsion protective coating.
PRECAUTIONS
Fire:
CytoProof 60 is not flammable. Ensure adequate
ventilation. Do not use near a naked flame and do
not smoke during use.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoproof 60_Page 2
CyTech International
Product Data Sheet
CYTOPROOF B-30
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
DESCRIPTION Flashpoint : N/A
Drying Times : 6-8hours per coat @
CytoProof B-30 is suitable for the treatment of 25C.
concrete, asphalt, metal, roofing felt and other Appearance : Dark black/brown
similar roofing surfaces whether flat, sloping or Coating. Cures to a
vertical. Where added protection is required on Hard tack free finish.
roofs, CytoProof B-30 may be used in conjuction Chemical resistance : Water, aqueous
with a reinforcing fabric. groundwater salt
Solutions, mild
TYPICAL APPLICATIONS detergents, acids and
Alkalis.
General waterproofing and damp proofing of
concrete, asbestos cement sheets, roofing felts, DIRECTIONS
wood etc.
Surface Preparation:
Protection of steelwork, pipes and metal. Surfaces to which CytoProof B-30 is to be applied
must be clean and free of dirt, dust, rust or any
ADVANTAGES other material which may impair adhesion. Where
moss or lichen is present, remove sheets. Cut
Vapour Permeable allows substrate to and reseal blisters in asphalt or roofing. Remove
breathe. chippings other than those that form the surface of
mineralised felt. Porous surfaces such as concrete
Reduced chloride penetration due to and fibre reinforced cement should be primed
hard impermeable surfaces. using CytoProof B-30 diluted 1:6 with clean water.
Simple and easy to use, no skilled labour Old concrete and steel must be structurally sound
required. prior to application.
Cytoprof_B_30_Page 1
CyTech International
Product Data Sheet
CYTOPROOF B-30
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
HEALTH AND SAFETY
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoprof_B_30_Page 2
CyTech International
Product Data Sheet
CYTOPROOF B-50
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
DESCRIPTION Drying Times : 6-8hours per coat @
25C.
CytoProof B-50 is suitable for the treatment Appearance : Dark black/brown
of concrete, asphalt, metal, roofing felt and Coating. Cures to a
other similar roofing surfaces whether flat, Hard tack free finish.
sloping or vertical. Where added protection Chemical resistance : Water, aqueous
is required on roofs, CytoProof B-50 may be groundwater salt
used in conjuction with a reinforcing fabric. Solutions, mild
detergents, acids
TYPICAL APPLICATIONS and Alkalis.
Easy application due to paintable CytoProof B-50 may be applied to damp but not wet
consistency, suitable for new and old surfaces, dampen brushes before and occasionally
concrete. during use to avoid clogging and ease application.
During hot, dry weather application may be assisted
Many areas of use, versatile. by dampening the surfaces to be treated.
Solids content : 50% +/- 3%. CytoProof B-50 is supplied in 20 and 200 litre
Specific gravity : 1.10 @ 25C units. Store in shaded warehouses away from heat,
Service Temperatures : -100C to +85C humidity or moisture. Shelf life will be 12 months.
Flashpoint : N/A
Cytoproof B-50_Page 1
CyTech International
Product Data Sheet
CYTOPROOF 50
Non fibrated bitumen emulsion coating of brushing consistency which dries to give a firm, flexible, jointless
waterproof and protective membrane.
HEALTH AND SAFETY
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoproof B-50_Page 2
CyTech International
Product Data Sheet
CYTOPROOF GP 40
Cold applied bitumen emulsion for waterproofing and protective coating applications.
CytoProof GP 40 complies with ASTM C309-93 Where CytoProof GP 40 is required to take a screed,
concrete curing requirements when applied at a rate the second coat must be binded with clean, dry
of 2m2 per litre, and BS6949: 1991 requirements sharp sand as soon as applied. The excess sand
for bituminous coating. should be brushed off when coating has dried.
DESCRIPTION CLEANING
CytoProof_GP40_Page 1
CyTech International
Product Data Sheet
CYTOPROOF GP 40
Cold applied bitumen emulsion for waterproofing and protective coating applications.
PACKAGING
PRECAUTIONS
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoProof_GP40_Page 2
CyTech International
Product Data Sheet
CYTOPROOF GP-50
Cold applied bitumen emulsion for waterproofing and protective coating applications.
CytoProof GP 50 complies with ASTM C309-93 Where CytoProof GP 50 is required to take a screed,
concrete curing requirements when applied at a rate the second coat must be binded with clean, dry
of 2m2 per litre, and BS6949: 1991 requirements sharp sand as soon as applied. The excess sand
for bituminous coating. should be brushed off when coating has dried.
DESCRIPTION CLEANING
CytoProof_GP_50_Page 1
CyTech International
Product Data Sheet
CYTOPROOF GP-50
Cold applied bitumen emulsion for waterproofing and protective coating applications.
PACKAGING
PRECAUTIONS
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoProf_GP_50_Page 2
CyTech International
Product Data Sheet
CYTOSEAL
Cold-applied, fuel resistant surface coating for asphaltic pavements.
CytoSeal_Page 1
CyTech International
Product Data Sheet
CYTOSEAL
Cold-applied, fuel resistant surface coating for asphaltic pavements.
by pulling a rubber faced squeegee along the STORAGE AND SHELF LIFE
ribbon, thus producing a new ribbon from the
residue left by the trailing edge of the squeegee. 12 months in original unopened drums.
The process is repeated and the ribbon of material Store under enclosed warehouse conditions.
is replenished as necessary.
Protect from freezing and direct sunlight.
When the first coat is dry and tack free, the second
coat is applied at right angles to the first coat. PRECAUTIONS
The newly cured surface dries to a dark grey/brown Health and Safety
colour and will darken to black charcoal after a CytoSeal has a coal tar base, which may cause
few days exposure. skin irritation.
For large areas CytoSeal may be sprayed using Avoid prolonged and repeated contact with skin.
specialised spray equipment (refer to Technical
Services Department). At all times wear suitable overalls, eye protection
and gloves during application.
Do not apply in damp weather, below 10C or
when rain is imminent. All exposed skin should be protected by barrier
cream. If material gets into eyes consult medical
PRIMING assistance immediately.
CytoSeal is a two-coat system therefore no priming Refer to Material Safety Data Sheet for further
is required. information.
LIMITATIONS FIRE
CytoSeal is not suitable for application on concrete In the event of fire, extinguish with C02 or foam.
or new mastic asphalt surfaces.
CLEANING
Coverage: 1 litre/rn2 per coat (two coats required). CyTech International CyTech International
Downsview house P.O. Box 20437
Little London Ajman Free Zone
Supplied in 200 litre and 25 litre drums. East Sussex, TN21 0BB Gate No. 4, Ajman, U.A.E.
United Kingdom Tel: +971 (6) 7407121
Tel: +44 (0) 1435 813647 Fax: +971 (6) 7408794
Fax: +44 (0) 1435 813667 E-mail: info@cyrusgroup.ae
E-mail: info@cyrusglobal.com www.cyrusglobal.com
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoSeal_Page 2
CyTech International
Product Data Sheet
CYTOSEAL 205FR
Cold applied, high performance, two-part, self-levelling polyurethane pavement joint sealant.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal_205FR_Page 1
CyTech International
Product Data Sheet
CYTOSEAL 205FR
Cold applied, high performance, two-part, self-levelling polyurethane pavement joint sealant.
APPLICATION Cleaning
Clean equipment with CyTech eco-cleanse solvent
Joint Preparation free cleaner. Remove CytoSeal 205FR from hands
The joint slots should be formed correctly. The using a proprietary hand cleaner, followed by
concrete must be dry, oil and moisture free. moisturising cream.
The slot must be prepared by the removal of dust PACKAGING & YIELD
and laitance by using grit blasting or by other
mechanical means. CytoSeal 205FR is supplied in 5 litre kits comprising
of 2 tins, part A and part B.
Blow the slot clean using dry, oil-free compressed
air. Ensure that a polyethylene foam joint filler is Each 5 litre tin of CytoSeal 205FR will yield
inserted firmly into the slot at the specified depth/ approximately 22 linear metres in a 15mm x
dimension. Before pouring the sealant, adhere a 15mm joint slot.
PVC tape/bond breaker onto the top of the foam
filler. This will prevent sealant adhesion to the foam CytoSeal Primer 2 is supplied in 500ml screw cap
filler. tins, each tin of primer is sufficient for 1 0 litres of
Cytoseal 205FR.
PRIMING
STORAGE & SHELF LIFE
CytoSeal Primer 2 shall be used to prime the slot
surfaces to be sealed. 1 2 months in the original, tightly sealed (unopened)
containers, indoors at temperatures between 5C
CytoSeal 205FR must be applied between 1/2 an and 25C
hour to 2 hours after priming. After 2 hours the
area to be sealed should be reprimed. PRECAUTIONS
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal_205FR_Page 2
CyTech International
Product Data Sheet
CYTOSEAL 205FR
Cold applied, high performance, two-part, self-levelling polyurethane pavement joint sealant.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal_205FR_Page 3
CyTech International
Product Data Sheet
CYTOSEAL 206
Cold applied, high performance, environmentally friendly, two part flexible cable slot, AGL and pavement
compound.
USES life, which significantly reduces maintenance costs.
Cytoseal_206_Page 1
CyTech International
Product Data Sheet
CYTOSEAL 206
Cold applied, high performance, environmentally friendly, two part flexible cable slot, AGL and pavement
compound.
MAINTENANCE APPLICATION
No special requirement, any damage identified Immediately after mixing operations pour CytoSeal
during normal inspections should be repaired or 206 into the prepared and primed substrate/slot.
replaced as appropriate. CytoSeal 206 has a pot life of 1 2 minutes @ 23C
and shorter at elevated temperatures, therefore,
APPLICATION INSTRUCTIONS any undue delay must be avoided.
All surfaces must be well prepared to remove Clean equipment with CyTech eco-cleanse solvent
dust and laitance by grit blasting, grinding, free cleaner. Remove CytoSeal 206 from hands
planing or other mechanical means to expose using Swarfega or similar hand cleaner, followed
a sound surface. by moisturising cream.
The slot should be blown out with dry, oil free LIMITATIONS
compressed air just prior to priming.
In areas where above normal abrasion resistance,
PRIMING very high movements (i.e. 50%+ MAF) or in
transition joints between concrete and asphalt
All substrates should be primed with CytoSeal pavements, specific details are required. Please
206 primer avoiding ponding and allowed to contact CyTech Technical Department for advice.
dry, such that all of the solvent has evaporated.
ESTIMATING
CytoSeal 206 should be applied within 12
hours of applying the primer. CytoSeal 206 is supplied in a composite 8- litre
pack. Yields will vary dependent on the area to be
In the event that the area is left more than 1 2 repaired or sealed. Please refer to CyTech Technical
hours after primer application before installation Department for advice.
of CytoSeal 206 the substrate must be re-primed.
PRECAUTIONS
MIXING
Health & Safety
CytoSeal 206 is supplied in a composite 8-litre pack, Always wear protective overalls, goggles and
comprising a large base tin and a small curing agent tin. gloves when handling CytoSeal 206.
The total contents of the small curing agent tin Refer to Material Safety Data Sheet for further
is decanted into the base large tin ensuring all information.
the contents of the small tin is removed and the CyTech International CyTech International
components are mixed for full one and a half Downsview house P.O. Box 20437
Little London Ajman Free Zone
minutes using a 1500 RPM site drill fitted with a East Sussex, TN21 0BB Gate No. 4, Ajman, U.A.E.
paddle stirrer. Particular attention must be paid to United Kingdom Tel: +971 (6) 7407121
ensure dispersal from the bottom and sides of the Tel: +44 (0) 1435 813647 Fax: +971 (6) 7408794
Fax: +44 (0) 1435 813667 E-mail: info@cyrusgroup.ae
tin. E-mail: info@cyrusglobal.com www.cyrusglobal.com
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal_206_Page 2
CyTech International
Product Data Sheet
CYTOSEAL BS
CytoSeal BS for limited movement joints and gap filling.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal_BS_Page 1
CyTech International
Product Data Sheet
CYTOSEAL F1
Pitch/PVC elastomeric fuel resistant joint sealant.
ASTM D3569-85, D3406-85 BS2499 1993 Fl. It is essential that CORRECT heating and approved
application equipment is used.
US Federal Specification 55-5-1614, 167b, 1401b.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal F1_Page 1
CyTech International
Product Data Sheet
CYTOSEAL F1
Pitch/PVC elastomeric fuel resistant joint sealant.
CLEANING
New concrete should be allowed to cure for
minimum of 14 days prior to sealing works.
All equipment should be cleaned thoroughly using
flushing oil. Ensure that flames are extinguished
STORAGE AND PACKAGING
prior to cleaning works.
DO NOT store in direct sunlight. CytoSeal F1
Spillages should be absorbed immediately with
should be stored in warehouse conditions not
sand, sawdust, vermiculite etc, and disposed of in
exceeding temperatures of 40C.
accordance with local regulations.
CytoSeal F1 is supplied in 26 Kg (20 litre) pails.
LIMITATIONS
PRECAUTIONS
CytoSeal F1 will not form a bond on asphalt
surfaces.
Health and Safety
Exercise extreme caution when handling hot sealant.
DESIGN FACTORS
CytoSeal F1 should not come in contact with skin,
Design of the joints should be such that the width
eyes, etc. If contact occurs remove immediately with
of the joint due to thermal movement does not
suitable cleansing cream followed by soap and water.
exceed the 25% movement accommodation factor,
expressed as a percentage of the joint width.
Wear suitable protective gloves, eye/face protection
and overalls.
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal F1_Page 2
CyTech International
Product Data Sheet
PRECAUTIONS
FIRE
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal F1_Page 3
CyTech International
Product Data Sheet
CYTOSEAL N1
Hot Applied Plasto-elastic Joint Sealant
For sealing joints in concrete and asphalt pavements, The joints to be sealed should be thoroughly
prefabricated road panels, transitional joints from blown with high-pressure air and cleaned with
concrete to bituminous substrates. CytoSeal N1 mechanical wire brushing or similar. Preparation
is also particularly suitable for airfield pavement and application works should be done as separate
joints where there is no risk of fuel spillage. tasks to avoid product contamination. For artificial
drying out of the joints, hot compressed air lances
ADVANTAGES may be used.
Superior to straight bitumen sealants. The CytoSeal Primer, which is specifically suited
to CytoSeal N1, must be used. The primer must
Very easy sealant removal from pails by completely cover the flanks of the joint arisses,
zip method. forming a film. It is advisable to prime a strip of
approx. 10mm width on the pavement on both
Resists flow on cambered pavements. sides of the joint.
Complies with the requirement of The pre-treated joints should only be sealed in dry
weather conditions and at surface temperature of
BS2499: Type N1: 1993 not less than +5C. Before sealing the joints the
ASTM D3405, D1190 following points should be considered prior to
MSHTO M301,M173 commencement of sealing works.
U.S. FEDERAL SPEC 55 S 164
The primer must have dried, i.e. it must be touch
PHYSICAL PROPERTIES dry.
Application Temperature : 50C-180C The primed joint must be dry and free from dust
Specific Gravity : approx. 1.1g/cm2 and moisture.
Primer : BS-Primer
Softening Point : 99C Care should be exercised to ensure that the
Resilience : 85% equipment used for application, is suitable for the
purpose.
APPLICATIONS INSTRUCTIONS
At the commencement of sealing works, CytoSeal
Melting N1 must reach the application temperature as
CytoSeal N1 must be heated indirectly and carefully specified. Application at lower temperatures than
to the application temperature in a boiler equipped specified will lead to impairment of the sealant
with mechanical agitation, and an oil jacket. It must flow thereby leading to voids and ineffective filling
be thermostatically regulated at all times. of the sealing slots.
Overheating of the sealant should be avoided, Sealant, which has already become cold must
as this will cause polymer breakdown leading to not be re-used and must be discarded.
reduced compressive strength.
CytoSeal_N1_Page 1
CyTech International
Product Data Sheet
CYTOSEAL N1
Hot Applied Plasto-elastic Joint Sealant
MATERIAL CONSUMPTION
PACKAGING
PRECAUTIONS
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
CytoSeal_N1_Page 2
CyTech International
Product Data Sheet
CYTOSEAL SS 207
Cold applied, high performance, two part, solvent free cable slot, AGL and pavement compound.
Cytoseal_SS_207_Page 1
CyTech International
Product Data Sheet
CYTOSEAL SS 207
Cold applied, high performance, two part, solvent free cable slot, AGL and pavement compound.
PACKAGING
MIXING
APPLICATION
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoseal_SS_207_Page 2
CyTech International
Product Data Sheet
CYTOSLURRY
CytoSlurry is a synthetic resin clear bitumen based on road surface slurry, hand applied system available in a
range of colours.
USES or can be pigmented to achieve any desired shade
for pavements, pathways, cycle carriageways and
CytoSlurry can be used as a coloured top coating sports surfaces.
on road surface internal carriage ways and sports
surfaces. It is also suitable as a wearing course. The system incorporates high rate additives to
provide effective penetration, softening point and
ADVANTAGES high stability.
Cytoslurry_Page 1
CyTech International
Product Data Sheet
CYTOSLURRY
CytoSlurry is a synthetic resin clear bitumen based on road surface slurry, hand applied system available in a
range of colours.
CLEANING
LIMITATION
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytoslurry_Page 2
CyTech International
Product Data Sheet
CYTOSTRIKE SB
CytoStrike SB is a solvent based mould release agent suitable for the mould shutter faces for concrete.
Exceed the needs of release agent as described by Do not apply during and when rain is expected.
ASTM & BS.
STORAGE AND SHELF LIFE
DESCRIPTION
Shelf life is 2 years in original unopened packaging.
CytoStrike SEF is a specially formulated solvent Keep away from direct sunlight.
based chemical mould release agent for high
quality, fair-faced and stain-free concrete. ESTIMATING AND PACKAGING
CytoStrike SB can be applied by brush, sponge, CytoStrike SB contains hydrocarbon oils and should
squeegee or lightweight horticultural sprayers. be treated as potentially harmful as with other
CytoStrike SB must be applied in a very thin coating heavy solvents like kerosene & diesel.
and any excess must be removed.
Cytostrike_SB_Page 1
CyTech International
Product Data Sheet
CYTOSTRIKE SB
CytoStrike SB is a solvent based mould release agent suitable for the mould shutter faces for concrete.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytostrike_SB_Page 2
CyTech International
Product Data Sheet
CYTOSTRIKE SB
CytoStrike SB is a solvent based mould release agent suitable for the mould shutter faces for concrete.
Exceed the needs of release agent as described by Do not apply during and when rain is expected.
ASTM & BS.
STORAGE AND SHELF LIFE
DESCRIPTION
Shelf life is 2 years in original unopened packaging.
CytoStrike SEF is a specially formulated solvent Keep away from direct sunlight.
based chemical mould release agent for high
quality, fair-faced and stain-free concrete. ESTIMATING AND PACKAGING
CytoStrike SB can be applied by brush, sponge, CytoStrike SB contains hydrocarbon oils and should
squeegee or lightweight horticultural sprayers. be treated as potentially harmful as with other
CytoStrike SB must be applied in a very thin coating heavy solvents like kerosene & diesel.
and any excess must be removed.
Cytostrike_SB_Page 1
CyTech International
Product Data Sheet
CYTOSTRIKE SB
CytoStrike SB is a solvent based mould release agent suitable for the mould shutter faces for concrete.
Cytech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Cytostrike_SB_Page 2
CyTech International
Product Data Sheet
HIGHSEAL
Cold-applied, fuel resistant surface coating for asphaltic pavements.
Highseal_Page 1
CyTech International
Product Data Sheet
HIGHSEAL
Cold-applied, fuel resistant surface coating for asphaltic pavements.
by pulling a rubber faced squeegee along the STORAGE AND SHELF LIFE
ribbon, thus producing a new ribbon from the
residue left by the trailing edge of the squeegee. 12 months in original unopened drums.
The process is repeated and the ribbon of material Store under enclosed warehouse conditions.
is replenished as necessary.
Protect from freezing and direct sunlight.
When the first coat is dry and tack free, the second
coat is applied at right angles to the first coat. PRECAUTIONS
The newly cured surface dries to a dark grey/brown Health and Safety
colour and will darken to black charcoal after a HighSeal has a coal tar base, which may cause
few days exposure. skin irritation.
For large areas HighSeal may be sprayed using Avoid prolonged and repeated contact with skin.
specialised spray equipment (refer to Technical
Services Department). At all times wear suitable overalls, eye protection
and gloves during application.
Do not apply in damp weather, below 10C or
when rain is imminent. All exposed skin should be protected by barrier
cream. If material gets into eyes consult medical
PRIMING assistance immediately.
HighSeal is a two-coat system therefore no priming Refer to Material Safety Data Sheet for further
is required. information.
LIMITATIONS Fire
HighSeal is not suitable for application on concrete In the event of fire, extinguish with C02 or foam.
or new mastic asphalt surfaces.
CLEANING
Coverage: 1 litre/rn2 per coat (two coats required). CyTech International CyTech International
Downsview house P.O. Box 20437
Little London Ajman Free Zone
Supplied in 200 litre and 25 litre drums. East Sussex, TN21 0BB Gate No. 4, Ajman, U.A.E.
United Kingdom Tel: +971 (6) 7407121
Tel: +44 (0) 1435 813647 Fax: +971 (6) 7408794
Fax: +44 (0) 1435 813667 E-mail: info@cyrusgroup.ae
E-mail: info@cyrusglobal.com www.cyrusglobal.com
CyTech products are guaranteed against defective materials and manufacture and are sold subject to standard terms and conditions of sale, copies of which are available on request.
Whilst all reasonable care is taken compiling this technical data sheet, all recommendations regarding the use of such products are made without guarantee since the conditions
of use are beyond the companys direct control. It is the customers responsibility to satisfy them selves that each product is fit for the purpose for which they intend to use it.
Highseal_Page 2