Professional Documents
Culture Documents
Discuss me ...
CALCULATION Client
SHEET SCI/BCSA Connections Group
BCSA Calcs by
RS
Checked by
AW
Date
May 2002
750kN
25
273 x 6.3 CHS Grade S275 25
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
750kN
480 diameter
Design Information:
End Plates: 25mm thick
Bolts: M24 8.8
Material: S275 steel
Weld: 12mm fillet
Created on 07 February 2013
259
Joints in Steel Construction: Simple Connections - Example 5 - column splices - CHS tension splice
Discuss me ...
3 CHECK 1
Recommended detailing Not Not All recommendations
practice Applicable Applicable adopted
3 CHECK 2
Complete end plate yielding 1610 750
4 CHECK 3
Bolt failure with end plate yielding 1036 750 CRITICAL CHECK
4 CHECK 4
Bolt failure 1584 750
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
5 CHECK 5
Weld
- Tension Capacity 1585 750 Full strength welds
5 CHECK 6
Member
- Tension capacity 1452 750
Yellow pages
273 X 6.3 CHS Grade S275 Standard connection Table H.36
Total number of bolts N = 8
End plate thickness = 20mm See
Table H.34
Tying capacity = 946 kN
note (2)
Applied force = 750 kN
750kN < 946kN O.K.
Created on 07 February 2013
Note: The capacity from Table H.36 is conservatively based on the thickest
section in the range.
260
Joints in Steel Construction: Simple Connections - Example 5 - column splices - CHS tension splice
Discuss me ...
Holes Dh = 26mm
750kN 750kN
e 1 = 53.5 t w = 6.3
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
D = 273
t p = 25
Basic requirement:
tp2 py plate f3
Ft
2
1 0.5
f3 = ( k3 + (k32 4 k1) )
2k1
D 273
r2 = + e1 = + 53.5 = 190
2 2
Dt 273 6.3
r3 = w = = 133.4
2 2
190
k1 = ln = ln1.42 = 0.354
133.4
k3 = k1 + 2 = 0.354 + 2 = 2.354
1
f3 = ( 2.354 + (2.3542 4 x 0.354)0.5)
2 x 0.354
= 6.19
261
Joints in Steel Construction: Simple Connections - Example 5 - column splices - CHS tension splice
Discuss me ...
p = 139
750kN 750kN
e 1 = 53.5 t w = 6.3
e2 = 50
Basic requirement:
NP
Ft t
1 1
1 + [ln = natural loge]
f3 f3 ln(r1/r2)
Pt from
Yellow pages
Pt = Exact bolt capacity = 198kN Table H.49
f3 = 6.19 CHECK 2
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
D 273
r1 = + e1+ eeff = + 53.5 + 50 = 240mm
2 2
D 273
r2 = + e1 = + 53.5 = 190mm
2 2
240
ln(r1/r2) = ln = ln 1.263 = 0.234
190
8 x 198
Bolt group capacity = = 1036kN
1 1
1 +
6.19 6.19 x 0.234
Ft N Pt
Pt from
Yellow pages
N Pt = 8 x 198 Table H.49
= 1584 kN
Created on 07 February 2013
262
Joints in Steel Construction: Simple Connections - Example 5 - column splices - CHS tension splice
Discuss me ...
CHECK 5: Welds
continuous
weld
750kN 750kN
D = 273mm
e 1 = 53.5 t w = 6.3
(ii) Ft D a pw
pw from
This material is copyright - all rights reserved. Use of this document is subject to the terms and conditions of the Steelbiz Licence Agreement
Basic requirement:
Ft A py
Yellow pages
A = 52.8 cm2
Table H.70
py from
py = 275 N/mm2 BS 5950 -1
Table 9
263