Professional Documents
Culture Documents
DDCTool
CMT DCS 500
Installation Instruction
DDCTool Installation
Introduction .............................................................................................................................. 1
What's new .............................................................................................................................. 1
What's not new ........................................................................................................................ 1
Upgrading ................................................................................................................................ 1
The way to the setups .............................................................................................................. 2
Installation Overview ................................................................................................................ 3
DDCTool Installation for Windows NT4
Installation for Windows NT4:................................................................................................... 5
Setup of CardWare .................................................................................................................. 5
Test of the CardWare installation ............................................................................................. 6
Setup of DDCTOOL program .................................................................................................. 7
Start Setup............................................................................................................................... 7
Disable SNAT624 driver......................................................................................................... 11
Starting DDCTool ................................................................................................................... 13
Uninstall DDCTool for Windows NT4 ..................................................................................... 14
DDCTool Installation for Windows 2000
Installation for Windows 2000: ............................................................................................... 15
Setup of DDCTOOL .............................................................................................................. 15
Start Setup............................................................................................................................. 15
Installation of SNAT624 ......................................................................................................... 20
Starting DDCTool ................................................................................................................... 21
Properties of ABB SNAT624-HDLC.. ..................................................................................... 22
Uninstall DDCTool for Windows 2000 .................................................................................... 25
What's new The new DDCTool, version 4.0, has the following enhancements:
Modification for the new PCMCIA card SNAT624.
New drivers for this new PCMCIA card SNAT624 for
WIN NT4 and WIN 2000.
The SETUP programs are totally new.
The CMT/DCS500 exists no more as a stand alone program.
What's not new DDCTool and CMT/DCS500: The new program version 4.0 has the
same functionality as the old version 3.4 for WIN 3.1x and
WIN 95/98:
CMT/DCS500: The new DDCTool version contains also the
CMT/DCS500 program part from the old version.
The CMT/DCS500 program part, used with DCS 500(B) and
UNITROL, can be used with one single drive only.
http://www.abb.com/dc
select DC-Drives,
then Downloads
then DCS 500
finally you will find PC Based Tools.
The way to the setups 1. Start your operating system if it does not start automatically.
2. Insert the "DC DRIVES Customer Information" CD-ROM into
the CD-ROM drive.
3. If autorun is enabled, the main menu will be shown
automatically. Please go to point 5
4. If CD-ROM did not start automatically, click the Start button and
then click Run. In the Open field type x:\autorun, where x is
the letter of the drive containing the CD-ROM. Click OK.
5. On the main menu click on Tools Installation.
Installation Overview
Installation of
DDCTool program
and the pcmcia
SNAT 624
Installation
under Windows
2000 or NT4
Setup of CardWare
Start of DDCTool
Please note:
- Before starting the setup take care that you have the
administrator access.
- Before starting the setup of DDCTool installation of
CardWare software is required.
For testing with the drive:
- Adapter to optical fibre cable: NDPC-02
- Double plastic fibre cable (10m)
- e.g. DCS 500 with SDCS-COM-5 or SDCS-COM-1
Setup of CardWare Please read at first the README.TXT of the CardWare CD-ROM in
the subdirectory DISK1.
Now start the setup of CD-ROM of CardWare. You will find the
setup under the subdirectory DISK1. Please follow these
instructions. After finishing the setup please allow a restart.
Test of the CardWare The correct installation of the CardWare program you can check
installation with the pccard SNAT624
Plug in the SNAT624.
The following window should be shown:
Please click No
On the task bar double click on the pcmcia symbol
Start Setup Before starting the setup you should close all other applications.
Start the setup by clicking on Installation of CMT/DDCtool NT.
Click Yes
Now the InstallShield Wizard will be opened.
Click Next
During installation the files will be copied, the driver for SNAT624
will be installed.
Select the profiles without CardWare one after the other and
disable them.
Starting DDCTool Connect the optical fibre cable between the NDPC-02, which is to
be connected to the SNAT624, and the connectors V1 and V2 of
the board (SDCS-COM-1 or SDCS-COM-5).
On desktop the setup has created the shortcut
Uninstall DDCTool for Click the Start button, then select Settings and then
Windows NT4 Control Panel.
After opening Add/Remove Programs select the program
DDCTool Ver. 4.0 (for NT4 or for 2000).
Please note:
- Before starting the setup take care that you have the
administrator access.
Start Setup Before starting the setup you should close all other applications.
Start the setup by clicking on Installation of CMT/DDCtool 2000.
Click Yes
Click Next
During installation the files will be copied, the driver for SNAT624
will be installed.
Starting DDCTool Connect the optical fibre cable between the NDPC-02, which is to
be connected to the SNAT624, and the connectors V1 and V2 of
the board (SDCS-COM-1 or SDCS-COM-5).
On desktop the setup has created the shortcut
Properties - General :
Properties - Driver:
Properties - Resources:
Uninstall DDCTool for With uninstalling all installations of the setup program will be
Windows 2000 deleted. Other saved files, like own saved parameter settings will
not be deleted.
Click the Start button, then select Settings and then
Control Panel.
After opening Software select the program
DDCTool Ver. 4.0 for WIN2000.
Postfach 1180
68619 Lampertheim GERMANY
Tel: +49 (0) 62 06-5 03-0
Fax:+49 (0) 62 06-5 03-6 09
www.abb.com/dc *175R0101A2160000*
*175R0101A2160000*