Professional Documents
Culture Documents
RA 10551
Edition: 2013-11
Maximum operating
pressure:
3000 psi (207 bar)
Code 61
Ordering code
01 02 03 04 05 06 07 08 09
MV015 61 1S 011 30 B1 T B 000
Technical data
The 15 series motors are hydraulically balanced internally and Oil supply lines are connected to ports A and B. Case drain lines
therefore no significant radial loads are induced on the motor can be installed on the C1 port. Reference motor unit drawings for
bearings which contribute to long service life. The motor can be additional case line locations and Case Drain section on page 23
configured with various bearing options to accommodate external for details. Using the A port as the inlet will provide clockwise
radial and axial loading. This data sheet details standard motors shaft rotation as seen from the front of the shaft. Using the B port
(see Figure 1); technically feasible, custom solutions may be will provide counter-clockwise shaft rotation also seen from the
offered. Please consult factory. front of the shaft (see Figure 2).
13 1
3
12
11
Technical data
2-port motor
A A
Clockwise C1 Counter-clockwise C1
rotation rotation
B
B
Motor specifications
Torque @ 3000 psid
Standard Displacement Pressure Speed
(207 bar)*
Series
Continuous Intermittent Continuous Intermittent Continuous
Code 61 (in3/rev) (cm3/rev)
(psid) (bar) (psid) (bar) (rpm) (rpm) (lb-ft) (Nm)
6 98 2000 2600 183 248
7 115 1900 2600 230 312
8 131 1800 2600 274 372
9.5 156 1700 2300 308 418
MV015 3000 207 3500 241
10.5 172 1600 2300 352 477
11.5 188 1600 2300 395 536
13 213 1500 2000 428 580
15 246 1500 2000 509 690
* Torque values are average performance data measured at maximum speeds with 100 SUS (20cSt) and
standard rotating group.
Note:
1. Intermittent duty cycle is six (6) seconds per minute.
2. Higher speeds or pressure may be permissible under certain conditions. Consult factory.
Technical data
High temperatures in the system greatly reduce the service Fluorocarbon (FKM) (Viton)
life of oil and rubber seals, as well as resulting in low vis- Temperature Range:
cosity, which in turn provides poor lubrication. Content of 20 F to +350 F (29 C to +177 C)
water shall be less than 0.1%.
Viton is a linear copolymer of vinylidene fluoride and hexa-
Oil used in the system should be filtered by a minimum of fluoro propylene which offers the widest temperature range
25 micron filter. and chemical resistance. The product is compatible and
recommended for use with most fluids and gases such as
Fluid Cleanliness petroleum, silicate ester, diester, halogenated hydrocar-
System Pressure bons, and most phosphate esters. Viton has very good
3000 psi / 207 bar ozone, weather and aging resistance. It is not recom-
19/17/14*
mended for ketones, glycol based brake fluids, superheated
steam, formic and acetic acids.
* ISO 4406 Standard
Viscosity
Technical data
Bosch Rexroth Rineer offers two types of rotary seals, Shaft seal options
namely radial lip seal and quad ring. The lip seal is only Seal Type Maximum Case Pressure External Loading
available in FKM. The quad seal is available in both NBR
Radial Lip Seal 35 psig (2.4 bar) Radial / Axial
and FKM. The radial lip seal accommodates external radial
loads imposed on the shaft to a greater degree than quad Quad Seal 100 psig (6.9 bar) Low Radial / Axial
Technical data
desired output torque and speed for a given application can in3 cm3
d Displacement cir or cc or
be used. Motor speed (shaft speed) is a function of flow rev rev
Metric: d x p d x p
T = T =
75.4 62.81
P x 9549.09 37.28 x 9549.09
T= = = 356 N-m Txn Txn
n 1000 Pshaft = Pshaft =
5252 9549.09
U.S.:
Q x p Q x p
P x 5252 50 x 5252 Pshaft = Pshaft =
T= = = 263 lb-ft 1714 599.29
n 1000
dxn dxn
Q = Q =
231 1000
Theoretical displacement (ideal no losses):
P x 5252 P x 9549.09
for condition T = 356 N-m (T = 263 lb-ft) n = n =
T T
Metric:
T x 75.4 T x 62.81
T x 62.81 356 x 62.81 d =
p
d =
p
d= = = ~130 cc
p 172
U.S.:
Unit Conversions
T x 75.4 263 x 75.4
d= = = 8 cir Quantity Symbol Metric Convert U.S.
p 2500
Torque T N-m 1.356 lb-ft
Power P kW x 1.341 hp
Referencing the chart Torque 8 cir (131 cc)
Displacement d cm3/rev 16.385 in3/rev
An 8 cir (131 cc) displacement motor at a pressure
2500 psid (172 bar) will develop torque of approximately Flow Rate Q lpm 3.78 gpm
Referencing the chart Total Required Flow 8 cir (131 cc) Pressure p bar x 14.504 psi
Technical data
220 58.1
200 52.8
180 47.6
160 42.3
140 37.0
gpm
lpm
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
6 cir / 98 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
260 192
240 177
220 162
200 147
180 133
160 118
140 103
N-m
lb-ft
120 88
100 74
80 59
60 44
40 29
20 15
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
240 63.4
220 58.1
200 52.8
180 47.6
160 42.3
140 37.0
gpm
lpm
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
7 cir / 115 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
320 236
300 221
280 206
260 192
240 177
220 162
200 147
180 133
N-m
lb-ft
160 118
140 103
120 88
100 74
80 59
60 44
40 29
20 15
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
gpm
lpm
140 37.0
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 200 400 600 800 1000 1200 1400 1600 1800
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
8 cir / 131 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
375 277
350 258
325 240
300 221
275 203
250 184
225 166
200 147
N-m
lb-ft
175 129
150 111
125 92
100 74
75 55
50 37
25 18
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
gpm
lpm
160 42.3
140 37.0
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 200 400 600 800 1000 1200 1400 1600 1800
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
9.5 cir / 156 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
425 313
400 295
375 277
350 258
325 240
300 221
275 203
250 184
225 166
N-m
lb-ft
200 147
175 129
150 111
125 92
100 74
75 55
50 37
25 18
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
gpm
lpm
160 42.3
140 37.0
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 200 400 600 800 1000 1200 1400 1600
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
10.5 cir / 172 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
500 369
475 350
450 332
425 313
400 295
375 277
350 258
325 240
300 221
275 203
N-m
lb-ft
250 184
225 166
200 147
175 129
150 111
125 92
100 74
75 55
50 37
25 18
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
gpm
lpm
180 47.6
160 42.3
140 37.0
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 200 400 600 800 1000 1200 1400 1600
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
11.5 cir / 188 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
550 406
525 387
500 369
475 350
450 332
425 313
400 295
375 277
350 258
325 240
300 221
N-m
lb-ft
275 203
250 184
225 166
200 147
175 129
150 111
125 92
100 74
75 55
50 37
25 18
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
gpm
lpm
180 47.6
160 42.3
140 37.0
120 31.7
100 26.4
80 21.1
60 15.9
40 10.6
20 5.3
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
13 cir / 213 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
600 442
550 406
500 369
450 332
400 295
350 258
N-m
lb-ft
300 221
250 184
200 147
150 111
100 74
50 37
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
325 85.9
300 79.3
72.6
250
66.0
225
gpm
59.4
lpm
200
52.8
175
46.2
150
39.6
125
33.0
100 26.4
75 19.8
50 13.2
25 6.6
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
rpm
206 bar (3000 psid) 172 bar (2500 psid) 138 bar (2000 psid)
103 bar (1500 psid) 69 bar (1000 psid) 35 bar (500 psid)
Torque
15 cir / 246 cc
psid
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000
700 516
650 479
600 442
550 406
500 369
450 332
400 295
N-m
lb-ft
350 258
300 221
250 184
200 147
150 111
100 74
50 37
0 0
34 52 69 86 103 121 138 155 172 190 207
bar
Technical data
Bearing data Standard motor (B1 bearing) with shaft code 30, 31, 34, 49, & 52
Bearing Load at Center of Output Shaft Load from Mounting Face at 3,000 HRS L10 Bearing Life
2200 2000
100 RPM
2000 1800 250 RPM
3000 HRS 500 RPM
1500 HRS 1000 RPM
1800
1000 HRS 1600 1500 RPM
2000 RPM
1600
1400
Radial (lbf)
Radial (lbf)
1400
1200
1200
1000
1000
800
800
600 600
400 400
100 200 400 600 800 1000 1200 1400 1500 1800 2000 0 0.5 1.0 1.5 2.0
Speed (rpm) Distance (in.)
Bearing loading
The bearings in the 15 Series can accept radial load per
the radial capacity charts above. Thrust loading is not
recommended for the standard motor. For thrust-type
applications, see the thrust capable motor bearing chart.
Technical data
100 RPM
250 RPM
500 RPM
12000 1000 RPM
1500 RPM
2000 RPM
Radial Load (lbf)
9000
6000
3000
0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Distance (in.)
Technical data
100 RPM
7000 250 RPM
500 RPM
1000 RPM
6000 1500 RPM
2000 RPM
5000
Thrust (lbf)
4000
3000
2000
1000
0
0 1000 2000 3000 4000 5000 6000
Radial Load (lbf)*
*Radial load located at center of effective output of the shaft.
Unit dimensions
Standard key
7.45 2.17
189.3 55.1
5.98
151.9
1.03 6.82
26.2 173.1
0.48
12.1 3.41 1/2-13UNC-2B
0.24 86.6 0.50 [12.7]
6.2
C1
5.000
5.70
6.05 C1 4.998 A
153.8 A 127.00 B 144.7
TYP
126.95
17
B
C2
1.250
1.248
31.75
31.70
0.315
Model #:
0.313
DETAIL A 7.99 MV015-61-1S-***-30-B1-**-000
7.94
Standard spline
7.45 2.17
189.3 55.1
5.98
151.9 6.82
1.03 173.1
26.2
0.48 3.41
12.1 86.6
0.24 1/2-13UNC-2B
6.2 0.50 [12.7]
1.38 C1
35.1
1.250 5.000
A 5.70
6.05 C1 1.246 4.998
B 144.8
153.8 31.76 127.00
TYP
31.65 126.95
17
B
C2
Model #:
MV015-61-1S-***-31-B1-**-000
Unit dimensions
Wheel motor
13.89
352.7
7.45 6.43
189.3 163.4
2.00
50.8 0.19
4.7 C1
5.500 5.70
6.05
C1 5.00 5.495
B A 144.8
153.8 127 139.69
139.56 17 TYP
B 1.626
1.624 C2
41.30
41.25
Model #:
MV015-61-1S-***-32-T1-**-000
1.250
1.248
C1 31.75
C1
31.70
5.000
5.70
6.05 4.998 A
153.8 127.0 B 144.8
TYP
126.9 17
A B 0.315
0.313 C2
8.00
7.95
1.59
40.5 1/2-13 UNC-2B
2.254 0.50 [12.7]
SAE CODE 61* EFFECTIVE
57.25
1-1/4" DIA. 4-BOLT FLANGE PORT 2X
NEAR AND FAR SIDE SAE 3/8" O-RING BOSS
*7/16-14 UNC-2B 0.75 CASE DRAIN PORT 4.508
0.771 114.5
0.767 TYP
0.190
19.58 0.188
19.48 1.60
4.83 40.6
4X 4.78
10-32 UNF-2B
0.50 [12.7]
0.875
0.874
22.21
22.19
45 DETAIL A KEYSEAT
3.187
80.95 Model #:
MV015-61-1S-***-34-B1-**-000
REAR VIEW
Unit dimensions
1.250
C1 1.38 1.246
35.1 31.8
C1
31.7
5.000
A 5.70
6.05 4.998
B 144.8
153.8 127.0
TYP
126.9 17
A B
C2
KEYSEAT
45
DETAIL A
3.187 Model #:
80.95
MV015-61-1S-***-49-B1-**-000
0.50 ENGAGED
12.7 1.15 [29.2]
EFFECTIVE SPLINE C1
5.000 5.96
6.05 4.998 A
B 151.4
153.8 127.00
126.95 17 TYP
B
C2
0.74
18.8
ENGAGED 4X
0.56
14.3
SAE CODE 61* 2X 0.40 THRU 2.254
1-1/4" 4-BOLT FLANGE PORT 3/8" O-RING BOSS 10.2 57.25
NEAR AND FAR SIDE CASE DRAIN PORT 14T, 12/24DP, 30PA, CLASS 7
RETRACTED FLAT ROOT SIDE FIT 4.508
*7/16-14 UNC-2B 0.75 [19.05] PER SAE J1926-1
EXTERNAL INVOLUTE SPLINE 114.5
PER ANSI B92.1-1996 TYP
0.85
21.6 0.64
16.3
1.87 0.74 1.77
47.5 18.7 45.1
Model #:
1.91
48.5 MV015-61-1S-***-50-B1-**-000
Unit dimensions
7.45 6.00
189.3 152.3
5.98
151.9 6.82
1.03 173.1
26.2
0.48 3.41
12.1 86.6
0.24 1/2-13UNC-2B
6.2 0.50 [12.7]
5.000
4.998
127.00
126.95
C1
A 5.70
6.05 C1
144.7
153.8 B TYP
17
B 1.250
1.248
31.75
C2
31.70
4X
2X 0.56[14.3]
SAE CODE 61* THRU ALL
1-1/4" 4-BOLT FLANGE PORT 3/8" O-RING BOSS
NEAR AND FAR SIDE CASE DRAIN PORT 2.254
*7/16-14UNC-2B x 0.75 [19.05] PER SAE J1926-1 57.25
4.508
114.5
TYP
Model #:
MV015-61-1S-***-52-B1-**-080
Sample of customer specific shaft.
5.500
4.27 5.495 C1
108.5 139.70
139.57 A
6.05 1.687
153.8 C1 42.85 B
5.00
127 17
B
1/2 NPT C2
1.50 4X
38.1 0.56
SAE CODE 61* 2X DRILL ROD THRD 14.3
WRENCH 2.254
1-1/4" 4-BOLT FLANGE PORT 3/8" O-RING BOSS 6 THRD'S PER INCH
FLAT 1-1/2" TAPER PER FT. 57.25
NEAR AND FAR SIDE CASE DRAIN PORTS
*7/16-14 UNC-2B 0.75 [19.05] PER SAE J1926-1 BEGINNING AT 1-23/64" 4.508
MAJ . (CA21-1) 114.5
6.82 TYP
173.1
3.41
86.6
45 4X
10-32 UNF-2B 0.50[12.7]
3.187
Model #:
80.95
MV015-61-1S-***-53-T1-D*-000
Engineering guidelines
Circuit design
Clockwise Counter-clockwise
rotation rotation
A C1 A C1
B C2 B C2
Bosch Rexroth Corp. All rights reserved Bosch Rexroth Corp. This document, as well as the data,
Hydraulics specifications and other information set forth in it, are the exclusive property
of Bosch Rexroth Corp. It may notbe reproduced or given to third parties
8 Southchase Court
with its consent.
Fountain Inn, SC 29644-9018 The data specified above only serve to describe the product. No statements
U.S.A. concerning a certain condition or suitability for a certain application can be
Telephone (864) 967-2777 derived from our information. The information given does not release the user
Facsimile (864) 967-8900 from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.
www.boschrexroth-us.com