Professional Documents
Culture Documents
TECHNICAL DATA
Supply voltage ............................. 24 V AC 20%, 50/60 Hz
in (90 mm)
3.5
or 1940 V DC
Power consumption .............................................. max. 5 W
4.3 in (110 mm)
I/O MODULES
TAC Xenta 401 has no inputs or out-
puts by itself. Instead, the required I/O module DI DI DO DO UI TI AO AO
number of I/O modules from the TAC status override override
TAC Xenta 400 series are used.
Xenta 411 10 - - - - - - -
The TAC Xenta 401 can have up to 10 Xenta 412 10 10 - - - - - -
I/O modules. Xenta 421 4 - 5 - - - - -
The table gives an overview of the Xenta 422 4 4 5 5 - - - -
different numbers of inputs and outputs. Xenta 451 - - - - 4 4 2 -
Xenta 452 - 41 - - 4 4 2 2
DI, DO: Digital input, output
UI: Universal input Xenta 471 - - - - 82 - - -
TI: Thermistor input Xenta 491 - - - - - - 8 -
AO: Analog output Xenta 492 - - - - - - 8 8
1
Status indication only when the 2
0/420 mA; 01, 0/210 V DC
corresponding universal inputs (UI) are used
as digital inputs.
SOFTWARE FEATURES
With the assistance of TAC Menta, a on/off delays network communication according to
graphical programming tool using Func- pulse counting (Digital Inputs only) the LONTALK protocol
tional Block Diagrams (FBDs), the equipment run time totals on selected communication with Central System
TAC Xenta 401 may be easily adapted to objects. via modem
different control and monitoring tasks. time schedules (start and stop times in The basic software is adapted to the cur-
The basic software includes pre- hours and minutes): weekly and holi- rent application by connecting pre-
programmed routines for: days programmed function blocks and
optimum start/stop programs adjusting the relevant parameters. These
reading of Digital Inputs (alarms, pulse connections and parameters are stored
counting, interlocks) control characteristic curves
PID control loops (loops may be con- in non-volatile memory.
reading of Universal Inputs (individu- The parameters may be changed during
ally selectable as analog or digital) nected in cascade)
from v 3.2 trend logging for up to 50 ongoing operation either from the Central
control of Digital Outputs System or from the TAC OP operator
channels is possible
control of Analog Outputs panel.
connection to 10 I/O modules
alarm handling; alarm conditions may
be detected via the digital or the analog local level operator interface via
inputs. TAC OP
SYSTEM CONFIGURATIONS
The TAC Xenta base units can be used in
different configurations.
Stand-alone (together with the required TAC
Vista
TAC Web
Vista browser
I/O modules). Management
level IP Network
Controllers, I/O modules and OPs in
small networks.
Controllers, OPs, I/O modules and other PCLTA
or
card
equipment in full network with suitable
TAC Xenta 901 TAC Xenta 511
adaptors, possibly with connection to a TP/FT-10
Automation
TAC Vista Central System (CS) level
Figure 2 shows an example of a net-
worked TAC Xenta configuration. TAC Xenta OP TAC Xenta OP
CABLES
G and G0: C1 and C2: The TAC Xenta Network guide (part
Min. cross-sectional area19 and TP/FT-10 allows the user to wire the no. 0-004-7460) gives a more
16 AWG. control devices with virtually no detailed description.
topology restrictions. The max. wire
Cable with modular jack for RS232
distance in one segment depends
serial communication port: Max. 30 ft.
on the type of wire and the
topology, see the table below.
Belden 85102, single twisted pair 8850 (2700 m) 1640 (500 m) 1640 (500 m)
Belden 8471, single twisted pair 8850 (2700 m) 1310 (400 m) 1640 (500 m)
UL Level IV 22AWG, twisted pair 4590 (1400 m) 1310 (400 m) 1640 (500 m)
Connect-Air 22AWG, one or two pairs 4590 (1400 m) 1310 (400 m) 1640 (500 m)
Siemens J-Y(st)Y 2x2x0.8 2950 (900 m) 1040 (320 m) 1640 (500 m)
4-wire helical twist, solid, shielded
TIA568A Cat. 5 24AWG, twisted pair 2950 (900 m) 820 (250 m) 1470 (450 m)
INSTALLATION MAINTENANCE
There is a label on the front of the control- Service pin The only care needed is to keep the
ler with both the numbers and the names To simplify network commissioning, there controller dry and to clean it externally
of the terminals (1 C1, 2 C2 and so on). is a service pin on the electronic unit with a dry cloth when needed.
The numbers are also shown in the plas- which, when pressed, identifies the unit
tic of the terminal part. on the network.
TAC and TAC products are trademarks and/or registered trademarks of TAC AB.
All other trademarks belong to their respective owners. Copyright 2001 TAC AB. All rights reserved.
tac-global.com
0-003-1629-6 (EN) 4 (4)