This instrument is a 4 digit, compact-sized portable
HH804W OMEGAnet On-Line Service Internet e-mail digital thermometer designed to use external 100 Plati- COMMISSION omega.com info@omega.com num RTD as temperature sensor. Temperature indication This device complies with Part 15 of the FCC Rules. HH804WE follows Reference Temperature/Resistance Tables (Pt385 Operation is subject to the following two condi- WIRELESS DUAL INPUT RTD tions:(1) this device may not cause harmful interfer- DIGITAL THERMOMETER Servicing North America: for European Curve, Alpha=.00385. Pt3926 for American Curve, Alpha=.003926. Pt3916 for Japan Curve, Al- ence, and (2) this device must accept any interference M4552/0711 U.S.A: One Omega Drive, Box 4047 INSTRUCTION pha=.003916.) received, including interference that may cause unde- SHEET Shop online at: omega.com e-mail: info@omega.com Stamford, CT 06907-0047 ISO 9001 Tel: (203) 359-1660 FAX: (203) 359-7700 sired operation. For latest product manuals: omegamanual.info Certified MADE IN TAIWAN Canada: e-mail: info@omega.com 976 Bergar SAFETY INFORMATION NOTE Laval (Quebec) H7L 5A1, Canada It is recommended that you read the safety and opera- This equipment has been tested and found to comply Tel: (514) 856-6928 FAX: (514) 856-6886 tion instructions before using the thermometer. with the limits for a Class B digital device, pursuant to e-mail: info@omega.ca Part 15 of the FCC Rules. These limits are designed to WARNING provide reasonable protection. This equipment gener- For immediate technical or application assistance: To avoid electrical shock, do not use this instrument ates, uses and can radiated radio frequency energy and, U.S.A Sales Service: 1-800-826-6342/1-800-TC-OMEGA when working voltages at the measurement surface if not installed and used in accordance with the in- and Customer Service: 1-800-622-2378/1-800-622-BEST over 24V AC or DC. Canada: structions, may cause harmful interference to radio communications. However, there is no guarantee that Mexico: En Espan ol: (001) 203-359-7803 WARNING interference will not occur in a particular installation If e-mail: espanol@omega.com To avoid damage or burns, do not make temperature this equipment does cause harmful interference to ra- FAX: (001) 203-359-7807 info@omega.com.mx measurement in microwave ovens. dio or television reception, which can be determined by turning the equipment off and on, the user is en- Servicing Europe: couraged to try to correct the interference by one or Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands more of the following measures: Tel: +31 (0)20 3472121 FAX: +31 (0)20 6434643 Toll Free in Benelux: 0800 0993344 e-mail: sales@omegaeng.nl - Reorient or relocate the receiving antenna. Czech Frystatska 184, 733 01 Karvin, Czech Republic - Increase the separation between the equipment and Republic: Tel: +420 (0)59 6311899 FAX: +420 (0)59 6311114 receiver. Toll Free: 0800-1-66342 e-mail: info@omegashop.cz - Connect the equipment into an outlet on a circuit dif- France: 11, rue Jacques Cartier, 78280 Guyancourt, France ferent from that to which the receiver is connected. Tel: +33 (0)1 61 37 2900 FAX: +33 (0)1 30 57 5427 - Consult the dealer or an experienced radio/TV tech- Toll Free in France: 0800 466 342 nician for help. e-mail: sales@omega.fr Germany/ Daimlerstrasse 26, D-75392 Deckenpfronn, Germany Shielded interface cables must be used in order to Austria: Tel: + 49 (0)7056 9398-0 FAX: +49 (0)7056 9398-29 Toll Free in Germany: 0800 639 7678 comply with emission limits. e-mail: info@omega.de Changes or modifications not expressly approved by United One Omega Drive, River Bend Technology Centre the party responsible for compliance could void the Kingdom: Northbank, Irlam, Manchester users authority to operate the equipment. ISO 9002 M44 5BD United Kingdom Certified Tel: +44 (0)161 777 6611 FAX: +44 (0)161 777 6622 Toll Free in United Kingdom: 0800-488-488 WIRELESS NOTE e-mail: sales@omega.co.uk Wireless receiver must keep a distance at least 40cm from the meter and meter to meter distance must be at least 30cm.
It is the policy of OMEGA Engineering, Inc. to comply with all
worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice. These products are not designed for use in, and should not be used for, human applications. 7. REL Relative mode (only Main display) 11. TYPE(Pt385/Pt3926/Pt3916) Input RTD SPECIFICATIONS OPERATING INSTRUCTIONS Press the REL key to enter the relative mode, zero the Probe select (second display) ELECTRICAL 1. Power Button display, and store the displayed Reading as a reference The Pt385/Pt3926 key switches the T2 input to select the Temperature Scale: Celsius or Fahrenheit user-selectable The key turns the thermometer on or off. In the SET value. REL is shown on the display. Press REL key Pt385, Pt3926 or Pt3916 RTD probe as input, when sec- Measurement Range: mode cannot be powered off. Exit SET mode to power again to exit the relative mode. The relative reference ond display input selected T2. When the thermometer is Pt385(100) -200C to 800C, (-328F to 1472F) off. value can also be entered by the user. (See SET mode turned on, it is set to the RTD selected that was in use Pt3916/Pt3926(100) -200C to 630C, (-328F to later in this manual). When the desired relative value has when the thermometer was last turned off. 1166F) APO function mode been entered, press REL key to enter the relative mode Resolution: 0.1C or 0.2F Press power key for more than 6 seconds to disable and than press SET key use the entered relative value 12. Hi/Lo Limits mode (only Main display) Accuracy: the auto-power function. The display will show APO as a reference value. Press REL key again to exit the Press Hi/Lo Limits key to enter the Hi/Lo Limits com- Accuracy is specified for operating temperatures over the OFF. relative mode. In the relative mode, the value (can not parative mode. When the input temperature value ex- range of 18C to 28C (64F to 82F), for 1 year, not >1999.9 counts) shown on the LCD is always the dif- ceeds the Hi or Lo Limits value, the beeper emits a con- including RTD probe error. 2. C/F Selecting the Temperature Scale (Main ference between the stored reference and the present tinuous or pulsed tone. Press Hi/Lo Limits key again to (0.05% rdg + 0.2C) on C scale display) reading. exit the Hi/Lo Limits mode. (0.05% rdg + 0.4F) on F scale Reading the main displayed in either degrees Celsius(C) Temperature Coefficient: or degrees Fahrenheit(F). When the thermometer is 8. HOLD mode (only Main display) 13. WIRELESS MODE: 0.1 times the applicable accuracy specification per C turned on, it is set to the temperature scale that was in use Press the HOLD key to enter the Data Hold mode, the Press the key for more than two seconds to start from 0C to 18C and 28C to 50C (32F to 64F and when the thermometer was last turned off. To change the HOLD annunciator is displayed. When HOLD mode is wireless function. Press the key again for another 82F to 122F). temperature scale, press the C/F key. selected, the thermometer held the present readings and two seconds to stop wireless function. The wireless mode Input Protection: stops all further measurements. Press the HOLD key will shut down if there is no wireless signal for two min- 24V dc or 24V ac rms maximum input voltage on any 3. Display Back-Light again to cancel HOLD mode causing thermometer to utes. combination of input pins. Press the key to turn on or turn off the Back-Light. resume taking measurements. In the MIN/MAX re- To SET CH/ID to 00,00, press the Hi/Lo Limits key Maximum Differential Common Mode Voltage cording mode, press HOLD key to stop the recording. (Maximum Voltage between T1 and T2 during meas- and power key for more than 6 seconds with the 4. T1 T2/T1-T2 Main display Input Selection Press HOLD key again to resume recording. (Previ- urement): 1volt. ously recorded read are not erased). meter powered down. The meter will set channel and ID The input selection indicates which input is selected for to 00,00 status. The second display will show 00, which Reading Rate: 1 time per second. main display; T1 probe, T2 probe or the difference be- means that the channel and ID has been set to 00. Input Connector: 9. SET mode (Relative value set, Time set and tween the two probes (T1-T2). When the thermometer is Accepts for RTD 3 wires or 4 wires subminiature Hi/Lo Limits value set) To check the channel and ID of the meter: turned on, it is set to T1, when main display input se- 4-Prong type connectors (flat blades spaced 7.9mm, 9.1 Press the SET key to enter relative values SET When the meter is off, press C/F key and for 5 lected T1, then T1 input can select alternate of probe by center to center). mode (Press ENTER key to skip setting relative pressing Pt385/Pt3926/Pt3916 key switch. seconds, LCDs main display will show channel number, Wireless Features: value). = = = =.= is displayed on the main display. the second display will show ID number. Frequency range: 910~920MHz (HH804W) The relative value is entered via overlay numbers, 868.1~868.5MHz (HH804WE) 5. TYPE(Pt385/Pt3926/Pt3916) Input RTD Probe Select (only Main display) press overlay ENTER key to store the relative value, Low current consumption less than 1mA. and advance to elapsed time set mode. The transmitting distance can reach 25M without mag- The TYPE key switches the T1 input to select the Pt385, Pt3926 or Pt3916 RTD probe as input, when main 9.2 Elapsed time set mode, (Press ENTER key to skip netic interference. Elapsed time set mode) =.= = = : = = is displayed in display input selected T1. When the thermometer is turned on, it is set to the probe selected that was in use second and third display. Time (hours, minutes, sec- ENVIRONMENTAL when the thermometer was last turned off. onds) value is entered via overlay numbers, press Ambient Operating Ranges: overlay ENTER key to store time value. Elapsed 0C to 50C (32F to 122F) <80% R.H. time starts from set time value. Storage Temperature: 6. MIN/MAX with Time record mode 9.3 Hi Limit value set mode, (Press ENTER key to skip -20C to 60C (-4F to 140F) <70% R.H. (only Main display) Hi Limit value set mode), = = = =.= is displayed in Press MIN/MAX key to enter the MIN MAX Re- main display, Hi Limit value is entered via overlay cording mode, (displays the Maximum reading with time, GENERAL Minimum reading with time and Average reading stored numbers, then press ENTER key to store the Hi Display: Limit value. = = = =.= is displayed in main display, in record mode). In the this mode the automatic Lo Limit value is entered via overlay numbers, then 4 digit liquid crystal display (LCD) with maximum power-off feature is disabled and key, C/F key, press overlay ENTER key to store the Lo Limit reading of 19999. REL key, SET key, Hi/Lo Limits key and main value and exit SET mode. Overload: ----.- or OL is display. display T1 T2 T1-T2 key, TYPE key are disabled. 9.4 When the thermometer is turned on it uses the relative Battery: The beeper emits a tone when a new minimum or maxi- value and Hi/Lo Limits values that were entered when 1.5V x 4 PCS (SIZE AAA) UM-4 R03. mum value is recorded. thermometer was last in use. Battery Life: Press MIN/MAX key to cycle through the MAX, MIN 200 hours typical with carbon zinc battery. and AVG readings. If an overload is recorded, the aver- Auto power off: 30 minutes, press power key to resume 10. T1/T2 T1-T2 second display Input Selection aging function is stopped. In this mode, press the operation. The input selection indicates which input is selected for HOLD key to stop the recording of readings, all values Dimensions: second display; T1 probe, T2 probe or the difference are held, press again to restart recording. 160mm(H) x83mm(W) x 38mm(D). between the two probes (T1-T2), when the thermometer To prevent accidental loss of MIN, MAX and AVG data, Weight: Approx. 255g including batteries. is turned on, it is set to T2 input can select alternate of this mode can only be cancelled by pressing and holding probe by second display Pt385/Pt3926/Pt3916 key the MIN/MAX key for 2 seconds. All recorded read- switch. ings are erased. RTD PROBE CONNECTION WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in Where Do I Find Everything I Need for P/N: 14061-0800-9 MINI DIN PLUG materials and workmanship for a period of 13 months from date of purchase. OMEGAs WARRANTY adds an additional one (1) month grace Process Measurement and Control? Rear view Front view period to the normal one (1) year product warranty to cover handling OMEGAOf Course! and shipping time. This ensures that OMEGAs customers receive maximum coverage on each product. Shop online at omega.com If the unit malfunctions, it must be returned to the factory for evaluation. OMEGAs Customer Service Department will issue an Authorized Return (AR) TEMPERATURE number immediately upon phone or written request. Upon examination by Thermocouple, RTD & Thermistor Probes, OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGAs WARRANTY does not apply to defects resulting from Connectors, Panels & Assemblies any action of the purchaser, including but not limited to mishandling, Wire: Thermocouple, RTD & Thermistor improper interfacing, operation outside of design limits, improper repair, or Calibrators & Ice Point References unauthorized modification. This WARRANTY is VOID if the unit shows Recorders, Controllers & Process Monitors evidence of having been tampered with or shows evidence of having been Infrared Pyrometers 3 Wires 4 Wires damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating PRESSURE, STRAIN AND FORCE conditions outside of OMEGAs control. Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs. Transducers & Strain Gages OMEGA is pleased to offer suggestions on the use of its various Load Cells & Pressure Gages products. However, OMEGA neither assumes responsibility for any Displacement Transducers omissions or errors nor assumes liability for any damages that Instrumentation & Accessories result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants FLOW/LEVEL only that the parts manufactured by the company will be as Rotameters, Gas Mass Flowmeters & Flow Computers specified and free of defects. OMEGA MAKES NO OTHER Air Velocity Indicators WA R RAN TIES OR REPRESE NTATIONS OF ANY KI ND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, Turbine/Paddlewheel Systems AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF Totalizers & Batch Controllers TEMPERATURE VSRESISTANCE TABLE (ITS90) MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE pH/CONDUCTIVITY ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The C Pt385 Pt3926 Pt3916 remedies of purchaser set forth herein are exclusive, and the total pH Electrodes, Testers & Accessories liability of OMEGA with respect to this order, whether based on -200C 18.521 16.996 17.057 contract, warranty, negligence, indemnification, strict liability or Benchtop/Laboratory Meters Controllers, Calibrators, Simulators & Pumps -100C 60.256 59.479 59.565 otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable Industrial pH & Conductivity Equipment 0C 100.000 100.000 100.000 for consequential, incidental or special damages. DATA ACQUISITION CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor 100C 138.505 139.272 139.171 shall it be used: (1) as a Basic Component under 10 CFR 21 (NRC), used in Data Acquisition & Engineering Software 200C 175.856 177.362 177.155 or with any nuclear installation or activity; or (2) in medical applications or Communications-Based Acquisition Systems used on humans. Should any Product(s) be used in or with any nuclear Plug-in Cards for Apple, IBM & Compatibles 300C 212.052 214.275 213.957 installation or activity, medical application, used on humans, or misused in Data Logging Systems any way, OMEGA assumes no responsibility as set forth in our basic 400C 247.092 250.018 249.584 WARRANTY / DISCLAIMER language, and, additionally, purchaser will Recorders, Printers & Plotters 500C 280.977 284.591 284.036 indemnify OMEGA and hold OMEGA harmless from any liability or damage HEATERS whatsoever arising out of the use of the Product(s) in such a manner. Heating Cable 600C 313.708 317.994 317.313 RETURN REQUESTS / INQUIRIES Cartridge & Strip Heaters 700C 345.280 - - Direct all warranty and repair requests/inquiries to the OMEGA Customer Immersion & Band Heaters Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, Flexible Heaters 800C 375.700 - - PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER Laboratory Heaters FROM OMEGAS CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be ENVIRONMENTAL MONITORING AND CONTROL OPERATOR MAINTENANCE marked on the outside of the return package and on any correspondence. The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit. Metering & Control Instrumentation Refractometers Pumps & Tubing WARNING FOR WARRANTY RETURNS, please FOR NON-WARRANTY REPAIRS, Air, Soil & Water Monitors have the following information consult OMEGA for current repair To avoid possible electrical shock, disconnect the available BEFORE contacting charges. Have the following Industrial Water & Wastewater Treatment pH, Conductivity & Dissolved Oxygen Instruments thermocouple connectors from the thermometer before OMEGA: information available BEFORE 1. Purchase Order number under contacting OMEGA: removing the cover. which the product was 1. Purchase Order number to cover PURCHASED, the COST of the repair, Battery Replacement 2. Model and serial number of the product under warranty, and 2. Model and serial number of the product, and 1. Power is supplied by 4pcs 1.5V (AAA SIZE) UM-4 3. Repair instructions and/or specific 3. Repair instructions and/or specific R03. problems relative to the product. problems relative to the product. OMEGAs policy is to make running changes, not model changes, whenever 2. The appears on the LCD display when replace- an improvement is possible. This affords our customers the latest in ment is needed. To replace battery remove screw from technology and engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC. back of meter and lift off the battery cover. Copyright 2011 OMEGA ENGINEERING, INC. All rights reserved. This 3. Remove the battery from battery contacts and replace. document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or 4. When not in use for long periods remove battery. in part, without the prior written consent of OMEGA ENGINEERING, INC. 5. Do not store in locations with high temperatures, or high humidity.
Cleaning Periodically wipe the case with a damp cloth and deter- gent, do not use abrasives or solvents.
*Software Operation manual is on the Software disk.
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd">
<HTML><HEAD><META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<TITLE>ERROR: The requested URL could not be retrieved</TITLE>
<STYLE type="text/css"><!--BODY{background-color:#ffffff;font-family:verdana,sans-serif}PRE{font-family:sans-serif}--></STYLE>
</HEAD><BODY>
<H1>ERROR</H1>
<H2>The requested URL could not be retrieved</H2>
<HR noshade size="1px">
<P>
While trying to process the request:
<PRE>
TEXT http://www.scribd.com/titlecleaner?title=Honeywell+7800+SERIES+Relay+Modules.pdf HTTP/1.1
Host: www.scribd.com
Proxy-Connection: keep-alive
Proxy-Authorization: Basic Y3M3MjpSaWdlc2E1MA==
Accept: */*
Origin: http://www.scribd.com
X-CSRF-Token: c20bd3039f9b31c075bbd0d85fdaf6e450834350
User-Agent: Mozilla/5.0 (Windows NT 6.1) AppleWebKit/537.31 (KHTML, like Gecko) Chrome/26.0.1410.64 Safari/537.31
X-Requested-With: XMLHttpRequest
Referer: http:/