Professional Documents
Culture Documents
MODEL XP-15K
ELENCO
Copyright 2012, 1991 by ELENCO All rights reserved. Revised 2012 REV-P 753015
No part of this book shall be reproduced by any means; electronic, photocopying, or otherwise without written permission from the publisher.
INTRODUCTION
Assembly of your XP-15K Regulated Variable Power Supply Kit will prove to be an exciting project and give much
satisfaction and personal achievement. If you have experience in soldering and wiring technique, you should have no
problem in the assembly of this kit. Care must be given to identifying the proper components and in good soldering habits.
Above all, take your time and follow the easy step-by-step instructions. Remember, An ounce of prevention is worth a
pound of cure. Avoid making mistakes and no problems will occur.
USE SAFETY GOGGLES WHEN ASSEMBLING THIS KIT!!
PARTS LIST
If you are a student, and any parts are missing or damaged, please see instructor or bookstore. If you purchased
this kit from a distributor, catalog, etc., please contact ELENCO (address/phone/e-mail is at the back of this manual)
for additional assistance, if needed. DO NOT contact your place of purchase as they will not be able to help you.
RESISTORS
Qty. Symbol Description Color Code Part #
r1 R2 150 5% 1/4W brown-green-brown-gold 131500
r2 R1, R4 2.2k 5% 1/4W red-red-red-gold 142200
r1 R3 2k Potentiometer 192421
CAPACITORS
Qty. Symbol Description Part #
r1 C2 4.7F 50V Electrolytic 264747
r1 C4 220F 16V Electrolytic 282244
r1 C3 470F 35V Electrolytic 284746
r1 C1 2,200F 35V Electrolytic 292226
SEMICONDUCTORS
Qty. Symbol Description Part #
r8 D1-8 1N4001 Diode 314001
r1 U1 LM317 Regulator 330317
r1 D9 LED Red 350002
MISCELLANEOUS
Qty. Description Part # Qty. Description Part #
r1 Transformer YD-1485 440111 r2 Screw 6-32 x 3/8 Blk 641652
r1 PC board 510002 r1 Nut 7mm 644101
r1 Heat sink 615009 r1 Nut 4-40 644400
r1 Knob 622009 r2 Nut 6-32 644600
r1 Case top 623061 r1 Washer flat 8 x 14mm 645101
r1 Case bottom 623062 r4 Washer fiber #6 645602
r1 Strain relief 2-wire 624002 r2 Lockwasher #6 646600
r1 Binding post black 625031 r4 Rubber foot 662015
r2 Nut binding post 625031HN r1 Label top 723071
r2 Lockwasher binding post 625031LW r1 Line cord 2 wire 862100
r1 Binding post red 625032 r 2 Shrink tubing 890120
r4 Screw 2.8 x 8mm 641102 r1 Solder lead-free 9LF99
r1 Screw 4-40 x 1/4 641430
-1-
PARTS VERIFICATION
Before beginning the assembly process, familiarize yourself with the components and this instruction book.
Verify that all of the parts are present. This is best done by checking off the parts in the parts list.
Carbon film
Diode
MISCELLANEOUS
Case top
Transformer YD-1485
Label
Lead-free solder
Case bottom
PC Board
Black Red
4-40 x 1/4 4-40 Heat sink
Fiber #6 Rubber foot
-2-
CONSTRUCTION
Introduction Turn off iron when not in use or reduce temperature setting when
The most important factor in assembling your XP-15K Regulated using a soldering station.
Variable Power Supply Kit is good soldering techniques. Using the Tips should be cleaned frequently to remove oxidation before it becomes
proper soldering iron is of prime importance. A small pencil type impossible to remove. Use Dry Tip Cleaner (Elenco #SH-1025) or Tip
soldering iron of 25 - 40 watts is recommended. The tip of the iron Cleaner (Elenco #TTC1). If you use a sponge to clean your tip, then use
must be kept clean at all times and well-tinned. distilled water (tap water has impurities that accelerate corrosion).
'
used by the electronics industry, but it is now being replaced by lead- Always wear safety glasses or safety goggles to
free solder for health reasons. This kit contains lead-free solder, which protect your eyes when working with tools or
contains 99.3% tin, 0.7% copper, and has a rosin-flux core. soldering iron, and during all phases of testing.
Lead-free solder is different from lead solder: It has a higher melting Be sure there is adequate ventilation when soldering.
point than lead solder, so you need higher temperature for the solder to Locate soldering iron in an area where you do not have to go around
flow properly. Recommended tip temperature is approximately 700OF; it or reach over it. Keep it in a safe area away from the reach of
higher temperatures improve solder flow but accelerate tip decay. An children.
increase in soldering time may be required to achieve good results.
Soldering iron tips wear out faster since lead-free solders are more Do not hold solder in your mouth. Solder is a toxic substance.
corrosive and the higher soldering temperatures accelerate corrosion, Wash hands thoroughly after handling solder.
so proper tip care is important. The solder joint finish will look slightly
duller with lead-free solders. Assemble Components
In all of the following assembly steps, the components must be installed
Use these procedures to increase the life of your soldering iron tip when
on the top side of the PC board unless otherwise indicated. The top
using lead-free solder:
legend shows where each component goes. The leads pass through the
Keep the iron tinned at all times. corresponding holes in the board and are soldered on the foil side.
Use only rosin core solder.
Use the correct tip size for best heat transfer. The conical tip is the
most commonly used. DO NOT USE ACID CORE SOLDER!
-3-
MOUNTING THE TRANSFORMER & BINDING POSTS
Case top
6-32 x 3/8
Screws
Figure A Figure B
-4-
ASSEMBLE COMPONENTS TO THE PC BOARD
Place a check mark in the box provided next to each step to indicate that the step is completed.
C4 - 220F Electrolytic
(see Figure D)
D4 - 1N4001 Diode
D5 - 1N4001 Diode D3 - 1N4001 Diode
D6 - 1N4001 Diode D2 - 1N4001 Diode
(see Figure C) D1 - 1N4001 Diode
R4 - 2.2k 5% 1/4W Res. (see Figure C)
(red-red-red-gold) D8 - 1N4001 Diode
C3 - 470F Electrolytic D7 - 1N4001 Diode
(see Figure D) (see Figure C)
r Mount the
LED to the
() (+) 4-40 Nut
copper side
of the PC () (+)
board, spaced 3/8 off the LED Figure F
board, with the flat side in
Long lead (+)
the same direction as Flat side
Flat side
shown in Figure F.
Short lead ()
R3 - 2k Potentiometer 2k Potentiometer
3/8
r Mount the potentiometer
to the copper side of the
PC board as shown in
Figure F. Insert the the
pins through the holes so
the body sits flat against
Copper side of PC board
the PC board, then solder
in place.
-5-
WIRING
Install the following wires as shown in Figure G.
r Cut the blue and both yellow transformer
wires so that they are 4. Strip 1/4
insulation off the ends. Blue wire Yellow wires
r Solder one of the yellow wires from the
transformer to PC Board P1 and the
other to P3.
r Solder the blue wire from the transformer
to the PC board hole P2.
r Solder the red wire from the P5 to the
end of the the red binding post.
r Solder the red wire from the P4 to the
end of the the black binding post.
r Install the PC Board into case by lining
up the shaft of the pot and the LED with
the holes in the case, and then pressing
PC board into place. Flip the case around
and install the 8 x 14mm flat washer and
7mm nut as shown in Figure H.
r Turn the shaft on the pot fully counter- Red wires
clockwise. Push the knob onto the shaft
so that the line on the knob lines up with
the end of the circle on the front panel as Black binding post
shown in Figure I. If the knob is loose on Red binding post
the pot shaft, insert a screwdriver in to
the slot and expand the slot slightly. If the Figure G
knob has a set screw, tighten the set
screw located on the side of the knob.
Line on
knob
7mm Nut
Flat head
8 x 14mm screwdriver
Flat washer blade
Knob
Pot shaft
Figure H Figure I
-6-
LINE CORD ASSEMBLY FINAL ASSEMBLY
Install the following wires as shown in Figure K.
r Remove the backing from each rubber foot and
r Cut the two black wires from the transformer to place them in the locations shown in Figure L.
1. Strip of insulation off of each wire.
r Assemble the top and bottom case sections and
r Feed 2 of line cord into the hole of the chassis. fasten with four 2.8 x 8mm self-tapping screws as
Place the line cord in the slot of the strain relief and shown in Figure L. Make sure the slots on the side
squeeze the two sections together with pliers. line up with one another.
Then, insert the strain relief into the hole, as
shown in Figure J. 2.8 x 8mm
r Separate the two line cord wires. Place 1 of shrink Screws
tubing over each black transformer wire. Twist and
solder the line cord wires to the black transformer
wires as shown in Figure K.
r Slide the shrink tubing up to cover the solder joints.
Shrink the tubing with the heat from your soldering 2.8 x 8mm Screws
iron. BE CAREFUL NOT TO TOUCH THE SHRINK Rubber feet
TUBING OR WIRES WITH THE IRON.
Strain relief
Pliers
Figure J
Slot
Bend wires Soldering
over as shown iron
Slide tubing
Figure L
-7-
TESTING THE XP-15K POWER SUPPLY
Testing the XP-15K Power Supply is very simple. Set the output voltage to 15 volts and place a 75 5
Before applying power to the unit, be sure that all of watt resistor across the output terminals. Again, the
the wiring and soldering is firm. If so, obtain a digital output should not change by more than 0.1 volts. In
voltmeter. Apply power to the XP-15K and vary the making these tests, the voltmeter leads should be
voltage control knob. clipped directly to the output terminals and not to
the load leads. This is to prevent errors due to
Next, short the output of the supply. It should turn off
voltage drop in the load leads.
and recover when the short is removed. If you have
a 4.7 1 watt resistor, set the voltage to 1.4 volts Should any of these tests fail, refer to the
and place is across the output terminals. The output troubleshooting guide.
of the supply should not change more than 0.1 volts.
CIRCUIT DESCRIPTION
INTRODUCTION
The XP-15K Power Supply features an output the XP-15K. Severe overloading or even short
voltage variable from 0 to 15V at 0.3 ampere circuiting the output will not damage the supply.
maximum current. The voltage is regulated to within Special turn-off circuits in the IC sense the overload
0.1V when going from no load to full load. Varying and turn off the output.
the input AC voltage from 110 to 130V will have
Figure 1 shows a simplified circuit diagram of the
practically no effect on the output voltage. This is
power supply. It consists of a power transformer, a
because of the specially designed IC circuit used in
DC rectifier stage and the regulator stage.
120VAC
Input 18VAC 20VDC 0 - 15V
Transformer AC to DC Voltage
120V to 18V Converter Regulator
Regulated
Simplified diagram of positive power supply Output
Figure 1
TRANSFORMER
The transformer T1 serves two purposes. First, it reduces the 120VAC input to Voltage Waveform for Supply
18VAC to allow the proper voltage to enter the rectifier stage. Second, it isolates
A) Transformer
the power supply output from the 120VAC line. This prevents the user from Winding AB
dangerous voltage shock should they be standing in a grounded area.
B) Transformer
AC to DC CONVERTER Winding BC
The AC to DC converter consists of diodes D1 and D3 and capacitor C1.
C) Output of
Transformer T1 has two secondary windings which are 180 degrees out of phase. diode D1.
The AC output of each winding is shown in Figure 2A and 2B. D) Output of
diode D3.
Diodes are semiconductor devices that allow current to flow in one direction. The E) Total of diodes
arrow in Figure 3 points to the direction that the current will flow. Only when the D1 & D3.
transformer voltage is positive will current flow through the diodes. Figure 3 shows
20V
the simplest possible rectifier circuit. This circuit is known as a half wave rectifier.
F) Output of capacitor C1
Here, the diode conducts only half the time when the AC wave is positive as shown Ripple depends on load
in Figure 2C. Use of this circuit is simple but inefficient. The big gap between cycles current (expanded).
requires much more filtering to obtain a smooth DC voltage.
Figure 2
By the addition of a second diode and transformer winding, we can fill in the gap
between cycles as shown in Figure 4. This circuit is called full wave rectification.
-8-
Each diode conducts when the voltage is positive. depending on the current drawn
By adding the two outputs, the voltage presented to by the output load. Remember, D1
capacitor C1 is more complete, thus, easier to filter, current only flows through the
C1
as shown in Figure 2F. When used in 60 cycles AC diode when the anode is more
input power, the output of a full wave rectifier will be positive than the cathode. Thus,
120 cycles. current will flow in short bursts Half Wave Rectifier
shown in Figure 2E. Because capacitor C1 has a current. The 1N4001 has a peak
charge after the first cycle, the diode will not current rating of 10 amps. D3
REGULATOR CIRCUIT
The regulator circuit in the Model XP-15K Power goes negative. Now, if the 1.25V output voltage
Supply consists of a LM317 integrated circuit. This goes down because of current drain at the output,
IC is specially designed to perform the regulation the base of Q2 will drop, forcing the collector voltage
function. Figure 6 shows a simplified circuit of how of Q2 to go higher. This will bring the output voltage
the LM317 IC works. back to 1.25V. This is the basis of all negative
Transistors Q1 and Q2 form a circuit known as a feedback regulators.
differential amplifier. Transistor Q1s base is Another feature of the LM317 regulator is to protect
connected to a stable 1.5V reference voltage. The the IC against overload and output shorts. If the IC
base of Q2 is connected to the regulator output is overloaded, the junction will overheat. A transistor
circuit through a voltage divider network. The will sense this overheating and shut down transistor
collector of transistor Q2 is connected to a current Q5.
source. This basically is a PNP transistor biased to The LM317 IC is basically a 1.25V regulator. To be
draw about 1mA current. Transistor Q2 sees the able to vary the output 0 - 15V, we stack the IC on
current source as a very high resistor of about 1 the negative 1.25VDC voltage as shown in Figure 7.
meg ohms. Thus, the gain of transistor Q2 is very When R3 equals 0, the output voltage is 0 volts.
high.
1.25V
Transistor Q5 is called the pass transistor. It controls Current Output
Q5 LM-317 0V - 15V
the current reaching the output. Transistors Q3 and Source
Equalized Q3 R1
R2
Q4 are emitter followers. Their function is to raise to 1 Meg. Q4
Figure 6 Figure 7
-9-
TROUBLESHOOTING GUIDE
Consult your instructor or contact ELENCO if you have any problems. DO NOT contact your place of purchase
as they will not be able to help you.
3) LED in backwards or defective. 2) If ripple is higher, check diodes D1, D3, and
the filter of capacitor C1.
No Output Voltage
1) Check AC voltage across points P1 & P2 or
P2 & P3. It should read about 18VAC. Copper Side of PC Board
2) Measure voltage at the output of D1 and D3.
It should read about 20VDC. If not, then
check D1, D3, C1, U1, R2, R3, D7, and D8.
QUIZ
1. AC voltage is supplied to the rectifier stages by the . . . 6. An inefficient rectification circuit usually contains . . .
r A. step up transformer. r A. large gaps between cycles.
r B. step down transformer. r B. twice the AC voltage needed.
r C. 1 to 1 transformer. r C. more diodes.
r D. AC to DC transformer. r D. all of the above.
2. The secondary windings of the transformer are . . . 7. The maximum current that a diode can handle is
r A. 90O out of phase. determined by . . .
r B. 180O out of phase. r A. the transformers current rating.
r C. 270O out of phase. r B. the amount of AC ripple.
r D. 320O out of phase. r C. three times the diode rating.
r D. peak current rating.
3. Diodes allow current to flow . . .
r A. when the anode is more negative than the 8. The LM317 will shut down when . . .
cathode. r A. the output voltage is too high.
r B. when the cathode is more positive than the r B. no current is being drawn.
anode. r C. the junction overheats.
r C. in one direction. r D. the output voltage drops to 1.25V.
r D. when a negative or positive voltage is on the
anode. 9. The LM317 regulator contains . . .
r A. a pass transistor.
4. What circuit is more efficient for rectifying AC to DC?
r B. a constant current source.
r A. Hartley oscillator.
r C. a differential amplifier.
r B. Half wave.
r D. all of the above.
r C. Schmitt trigger.
r D. Full wave.
10. The LM317 is . . .
5. The DC voltage is smoothed by using a . . . r A. a positive voltage regulator.
r A. half-wave rectification circuit. r B. a 6.25V regulator.
r B. small value capacitor with a high voltage value. r C. a 2.5V regulator.
r C. Large value capacitor. r D. a negative voltage regulator.
r D. 90O out of phase rectification circuit.
-10-
SCHEMATIC DIAGRAM
REV-A
6. D, 7. D, 8. C, 9. D, 10. A
Answers: 1. B, 2. B, 3. C, 4. D, 5. C,
ELENCO
150 Carpenter Avenue Wheeling, IL 60090
(847) 541-3800 Website: www.elenco.com e-mail: elenco@elenco.com