Professional Documents
Culture Documents
Subscribe to feed
Home
ERROR DISPLAY
Brother Resetter
Errors are displayed by the LEDs, and ink low warnings are displayed by the Status Canon Resetter
Monitor. Samsung Resetter
3-1. Operator Call Error (Alarm LED Blinking in Orange) Hp Resetter
Epson Resetter
Alarm LED
blinking Error Corrective action There was an error in this gadget
2 times No paper Set paper, and press the Resume/Cancel button to feed the
paper. About this blog
3 times Paper jam Remove the jammed paper, and press the Resume/Cancel
button.
4 times No ink Replace the ink cartridge(s), or press the Resume/Cancel
button to continue printing Followers
without replacing the ink cartridge(s).
5 times The ink cartridges are not properly installed, or a non-supported ink Followers (13)
cartridge is installed
(the ink cartridge EEPROM data is abnormal).
Install the ink cartridges properly.
Or, confirm that the supported ink cartridges are
installed.
7 times Ink cartridge not installed Install the ink cartridge(s), and close the
access cover. Follow
8 times Waste ink absorber full or platen waste ink absorber full warning
(approx. 95% of the maximum capacity)
Archives
Pressing the Resume/Cancel button will exit the
error, and enable printing.
2011 (1)
14 times Non-supported ink cartridge installed Replace the non-supported ink
August (1)
cartridge with the
supported one. Aug 31 (1)
16 times Used ink cartridge installed, or no ink Pressing the Resume/Cancel Waste Ink Counter Resett
button will exit the error, and enable printing.
Foreign material or paper debris around the purge drive system unit;
- remove foreign material.
If other solution fail, replace one off the following
- Purge drive system unit
- Logic board
Ink absorber is full or waste pad inside the printer is almost full
- Replace printer's Ink absorber pad and reset the ink absorber counter
value in the EEPROM.
Click here for your printer model reset procedure and service tools
Turn off the printer and then turn on if error still persist replace Ink
cartridge or print head
Replace Print head and logic board (Replace them at the same time.)
Replace Power supply unit
Check and Clean Head contact pin condition of the carriage unit
Check Cable connection especially the carriage FFC
Check for foreign material or paper debris around the purge drive system
unit
- remove foreign material.
Check for foreign material or paper debris around the ASF unit
- remove foreign material.
If other solution fail, replace one off the following part
- Purge drive system unit
- Logic board
check for foreign material or paper debris around the purge drive system
unit;
- remove foreign material.
check for foreign material or paper debris around the ASF unit;
- remove foreign material.
If other solution fail, replace one off the following part
- Purge drive system unit
- Logic board
Jammed paper in the PF rear guide (when a large amount of ink was
absorbed in the paper);
- remove the jammed paper and foreign material.
check for foreign material or paper debris in the cassette or in the PF rear
guide;
- remove foreign material.
If other solution fail, replace one off the following part
- PF pick-up unit
- Logic board
check for foreign material or paper debris around the purge drive system
unit;
- remove foreign material.
Replace
- Purge drive system unit
- Logic board
This is for Old Canon Printer Error Code (MP198, MP145, MP160, Etc)
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 =The ink cartridges are not installed or a non-supported ink cartridge is
installed,or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 =The connected digital camera / video camera does not support Camera
direct Printing
E14 =The Ink cartridges whose destination are wrong
E15 =Ink cartridge is not installed
E16 =Ink remaining is unknown
E16-E19 = Failed to scan head alignment sheet
E22 =Carriage error
E23 =Paper feed error
E24 =Purge unit error
E25 =ASF(cam) sensor error
E26 =Internal temperature rise error
E27 =Waste ink absorber full or platen waste ink absorber full
E28 =Ink cartridge temperature rise error
E29 =EEPROM error
E33 =Paper feed position error
E35 15 =USB Host VBUD overcurrent error - USB
E37 17 =Abnormal motor driver error
CANON MX318
If you encounter a problem or an error like "Ink absorber is full" or Error Code 27
or "Error Code 5B00". Its mean that the Printer Counter Protection is Full and it
required a reset and Ink wastepad replacement, if you want your printer to work
again. There are two ways to reset the Canon MP (all in one) printer, One is by
using a Software tool and the other is manually resetting the EEPROM of the
printer. Below is the step by step procedure on how to reset your Canon MP (All in
One) printer.
Please follow the step by step procedure to reset your Canon Pixma MX318 Printer
Mode:
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
7. After selecting the desired mode (eg 4), press the POWER button to "set"
the change, and return to the top of the function selection menu. Press the
POWER button again to restart the printer. Or unplug the printer to turn
off.
8. On the Canon Pixma MX318 Printers, And your done!
Warning: Getting rid of the error message wont change that you might
end up with ink leaking out of the printer if you dont either replace or
clean the ink wastepad.
CANON MP Series
If you encounter a problem or an error like "Ink absorber is full" or Error Code
27 or "Error Code 5B00". Its mean that the Printer Counter Protection is Full and
it required a reset and Ink wastepad replacement, if you want your printer to work
again. There are two ways to reset the Canon MP (all in one) printer, One is by
using a Software tool and the other is manually resetting the EEPROM of the
printer. Below is the step by step procedure on how to reset your Canon MP (All in
One) printer.
This procedure and resetter also work fine on following canon printer models:
Canon MP150, Canon MP160, Canon MP170, Canon MP180, Canon MP450 and
Canon MP460 printer.
Warning: Getting rid of the error message wont change that you might
end up with ink leaking out of the printer if you dont either replace or
clean the ink wastepad.
P03 (Line feed error): an error in transmission line entering the line feed (LF)
is a signal telling the printer to move to another line or a whole new line that
would not otherwise have reached the end of the line.
1. Check wire print head position (timing slit disk film) on the side of the
machine.
2. Check PCB logic board.
P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full
1. Replace the wastepad inside the printer or install waste ink bin outside the
printer
2. then Reset counter protection.
P08 (Print head temperature rise error): caused by thermal print head
temperature exceeds a threshold.
1. Replace the new cartridge print head and / or change a new logic board.
P15 (USB VBUS over current): caused by too much current, try removing the
USB cable and then plugin again, if solve the error, try to replace with a new USB
cable. If the error still exist replace the logic board.
1. Pressing the Stop / Reset button for 5 to 8 seconds until the led screen
display number 1.
CANON IP2770
1. Canon PIXMA iP2770 are classified into photo printers. This printer is very
suitable for use at home. Results in getting the equivalent of lab quality
photos. The speed of this printer quickly spelled out that is about 7 ipm for
mono and the 4.8 ipm for color and for 4R-sized photo takes 55 seconds.
Resolution of Canon PIXMA iP2770 printer at 4800 x 1200dpi (max). Still
uses USB 2.0 connectivity and the type cartridge using PG-810, CL-811
(PG-810XL, CL811XL Optional). For this printer weight of 3.4 kg with
dimensions of 445 X 250 X 130mm.
If a lights blink on the POWER and RESUME button alternately and it will
show an error 5B00. It means that your ink absorber inside the printer is
almost full. In order to solve this you need to clear or reset the counter
protection of your printer. To do this, follow this steps.
First make sure that the power cable and usb cable are connected, before
you perform the reset procedure. And download the resetter at the bottom
of this post.
Warning: Getting rid of the error message wont change that you
might end up with ink leaking out of the printer if you dont either
replace or clean the ink wastepad.
Download
here
CANON IP1980 & IP 1880
When you try to print and a pop-up message appear saying that "The ink absorber is
full" it means that the ink absorber or wastepad inside your printer is almost full. In
order to solve this you need a technical knowledge on how to disassemble the printer
and software resetter.
First you have to enter in service mode state in order to used the resetter. To do that
follow this procedure,
1. Unplug the power cable of the printer.
2. Press and hold down the power button with your index finger and then plug-in the
power cable.
3. While holding down the power button, press the reset/resume button twice and
release the power button
4. You will notice that the Alternate Blinking error is gone, this means that the printer
is in Service Mode state.
5. Using Canon Resetter
Download
Canon ip1980 here
Canon ip1880 here
1. After you download the resetter, extract it and double click "GeneralTool"
2. Select or Check the EEPROM CLEAR then click the MAIN button, you will notice
that the power button light will blink. It means that the it clear the waste ink counter.
Warning: Getting rid of the error message wont change that you might end
up with ink leaking out of the printer if you dont either replace or clean
them.
Home