You are on page 1of 27

engineering &

technical data
common valve designs & applications 1.1
Gate & Globe Valve / Check Valve / Butterfly & Ball Valve

valve sizing equations 1.4


units & unit conversions 1.5
temperature conversions 1.10
pressure ratings & flange compatibility 1.11
flanges 1.13
To AS2129 / To ANSI B16.5 / To BS4504; DIN*

hex head bolt & nut or bolt only dimensions 1.26


gate & globe valve design & Application
Gate Valve

engineering & technical data gate & globe valve design & application
Gate valves are by far the most widely used in industrial piping. They
are used as stop valves - to fully shut off or fully turn on flow - the
only job for which gate valves are recommended.
Gate valves are inherently suited for wide-open service. Flow moves
in a straight line and practically without resistance when the wedge
is fully raised.
Seating is perpendicular or at right angles to the line of flow. That is
one reason why gate valves are impractical for throttling service and
for too frequent operation.
Repeated movement of the wedge near the point of closure under
high velocity flow, may create a drag on the seating surfaces and
cause galling or scoring on the down-stream side. A slightly opened
edge may cause turbulent flow with vibration and chattering of the
wedge.
Cross section of valve in the fully Cross section of valve closed. A Gate valve usually requires more turns and therefore more work
open position. No resistance to flow. to open it fully. Also, unlike many globe valves, the volume of flow
through the valve is not in direct relation to the number of turns of
the handwheel.
Since most gate valves have a wedge with matching tapered
seats, refacing and repairing of the seating surfaces is not a simple
operation.
Gate valves, while not designed for throttling or too frequent
operation are generally ideal for services requiring full flow or no
flow.
Applications
Stopping and starting flow with infrequent operation of gases and
liquids. Knifegate valves for slurries, fibres, powders and granules,
vacuums and cryogenics.

Globe Valve
Unlike the perpendicular seating in gate valves, globe valve seating
is parallel to the line of flow. All contact between seat and disk ends
when flow begins.
These are advantages for more efficient throttling of flow, with
minimum wire drawing and seat erosion.
The valvedisk and seat in most globe valves can be conveniently
repaired or replaced - often without removing the valve body from
the line.
Shorter disk travel - with fewer turns required to operate, globe
valves save considerable time, work and wear on valve parts.
Seating is parallel to line of flow, and all seat and disk contact ends
as soon as the valve is Cracked Open. Fully opening or closing
requires fewer turns than a gate valve.
Globe valves, while not recommended where resistance to flow
Cross section of globe valve. Cross section of valve closed.
and pressure drop would be objectionable, are generally ideal for
Changing direction of flow means
greater resistance to flow.
throttling, and preferable for frequent operation.
Applications
Throttling flow or stopping and starting flow with frequent operation
of gases, mostly free of solids; liquids mostly free of solids; vacuums
and cryogenics.

1.1
June 2010
check valve design & application
Swing Check Valve Lift Check Valve
engineering & technical data check valve design & application

Swing check valves work Lift check valves also work


automatically as shown, in automatically with line
either horizontal or vertical pressure in horizontal pipelines
(flow upward) pipelines. They only with the bonnet vertically
must be installed with normal above the valve. Flow arrow on
flow opening the disc. Flow side of body indicates correct
arrows on the side of body installation direction.
indicates correct installation
Like a globe valve, with its
direction. Cross section of valve open. Cross section of valve open.
indirect line of flow, lift check
Moving through the line, the valves are flow restricting,
flow automatically swings the therefore are generally used as
disc open to full flow as in a a companion to globe valves.
gate valve.
Line pressure lifts the disc, and
Should flow reverse, the path of flow is in a changing
reversed pressure and the discs course as through a globe
weight closes the disc against valve.
the seat, and back-flow is
When flow reverses, the disc
stopped.
falls to its seat and cuts off
Applications back-flow.
To prevent reverse flow where Cross section of valve closed. Cross section of valve closed.
Applications
flow restriction in the open
To prevent reverse flow where
position must be minimal.
flow restriction in open position
is not objectionable.

Double Disc Check Valve Tilting Disc Check Valve


Double disc check valves work Tilting disc check valves are a
automatically with the line variation of the swing check
pressure. design that can be installed
horizontally or vertically in
Flow travelling in the desired
pipelines provided fluid flow is
direction folds semi-circular
upward.
plates together in the middle
of the stream. The pivot is offset between
the center and top of the disc
If the flow reverses, the
to partially counter balance Cross section of valve open.
plates close against the seat
Cross section of valve open.
the disc and aid operation
preventing back flow.
where only a small pressure
Spring loaded light weight differential is available to open
plates enable operation in the valve.
almost any position, allowing
Closure occurs more gradually
the most efficient piping layout.
than in a swing check valve.
Double disc check valves Tilting disc check valves are
are generally smaller, more therefore sometimes used
economical with lower flow where frequent change of fluid
restriction than swing check direction is to be encountered.
valves.
Applications
Applications To prevent reverse flow
Cross section of valve closed.
To prevent reverse flow where where only a small pressure
valve size and flow restriction differential is available to
Cross section of valve closed. open valve or where rapid disc
must be minimised.
closure is not desirable.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.2 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
butterfly & ball valve design & application
Butterfly Valve

engineering & technical data butterfly & ball valve design & application
Butterfly valves are often used because they are suitable for isolation
and throttling service.
Butterfly valves are compact and light weight - no additional
supports are required for their installation in line.
A quarter turn of the circular disc fully opens or closes the valve.
In the fully open position the thin disc of a butterfly valve causes
Cross section of a butterfly valve Cross section of a butterfly valve
minimal flow restriction.
in the fully open position. in the throttling position.
Sensitive flow control can be provided when the valve is open
between approximately 20 and 70 degrees.
Butterfly valves are also used where frequent operation is
encountered.
A wide variety of disc and liner materials are available so that
butterfly valves can be used for the control of most fluids which are
corrosive and/or errosive.
Applications
Stopping and starting flow or throttling flow of gases, liquids,
slurries, powder, grannules, sanitary, handling of pharmaceuticals,
food and vacuums.
Cross section of a butterfly valve in the fully closed position.
Ball Valve
Ball valves are used mainly as isolation valves. A quarter turn of the
ball containing a port either fully opens or closes the valve.
In the fully open position there is virtually no obstruction to flow and
head loss though full port ball valves is almost negligible.
The floating ball style of ball valves uses the pressure of the fluid
to enhance the seal. When the valve is in the closed position, the
pressure of the fluid on the upstream side of the valve pushes the
ball more firmly against the seat on the down stream side.
When used for thottling the pressure drop is distributed over two
orifices reducing velocity and erosion effect and improving the flow
Cross section side view of open valve. pattern on low flow.
Ball valves provide reliable throttling of gases and liquids within the
20 to 90 degrees open range.
Applications
Starting and stopping flow, moderate throttling or flow diversion of
gases, liquids, non- abrasive slurries, vacuums and cryogenics.

Cross section top view of valve in throttling position.

1.3
June 2010
valve sizing equations
The following equations can be used for the sizing of isolation and
engineering & technical data valve sizing equations

control valves. However these equations do not include correction


factors to account for pipe reducers, fluid viscosity, cavitation,
flashing, mixed phase behaviour and fluid compressibility. If any
of these factors are of concern, Tradelink specialists are at your
disposal to look at any particular problem regarding valve sizing and
selection.

Liquids Nomenclature
For non-critical flow P = P1 - P2
= Valve pressure drop
Kv = Q(d/P) 0.5
(Bar)
P = d(Q/Kv) 2
P1 = Pressure at valve inlet
Gases (Absolute Bar)
Equations to check for critical flow
P2 = Pressure at valve outlet
P < CP1 /2 for non-critical flow (Absolute Bar)
P CP1 /2 for critical flow
d = Specific gravity of fluid :
Valve sizing equations for non-critical gas flow - relative to water for liquids
- relative to air for gases at temperature of flow in
Kv = (Q/456)(dT/(P*Pm)) 0.5 circuit (d = 1 for water or air)
P = P1- (P12 - 2dT(Q/(456Kv)) 2) 0.5
Kv = Flow coeffiecient
Valve sizing equations for critical gas flow = 0.862 Cv
(m3 per hour)
Kv = (Q/293P1)(dT/C) 0.5
Cv = Flow coefficient
= 1.16 Kv
(US gallons per minute)

Q = Flow rate
(m3 per hour)

T = Fluid temperature
= degrees celcius + 273
(degrees Kelvin)

C = Valve recovery rate


(See table 1 below for butterfly valve figures)

Pm = ( P1 + P 2 ) = mean pressure
2 (Absolute Bar)

Angle Open 0 10 20 30 40 50 60 70 80 90
C 0 0.79 0.78 0.75 0.69 0.60 0.50 0.40 0.34 0.33

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.4 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
UNITS & unit conversions
Metric Unit Prefixes

engineering & technical data units & unit conversions


Quantity Name Symbol
length metre m
mass kilogram kg
time second s
electric current ampere A
thermodynamic temperature kelvin K
luminous intensity candela cd
amount of substance mole mol

Metric Unit Prefixes


T tera 1012 = 1 000 000 000 000
G giga 10 9 = 1 000 000 000
M mega 10 6 = 1 000 000
k kilo 10 3 = 1 000
h hecto 10 2 = 100
da deka or deca 101 = 10
d deci 10 -1 = 0.1
c centi 10 -2 = 0.01
m milli 10 -3 = 0.001
micro 10 -6 = 0.000 001
n nano 10 -9 = 0.000 000 001
p pico 10 -12 = 0.000 000 000 001

valves
mm 6 8 10 15 20 25 32 40 50 65 80 90 100 125 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900
in. 1
/4 /16
5 3
/8 /2
1 3
/4 1 1 /4 1 /2
1 1
2 2 /2
1
3 31/2 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 21 34 36

joints
mm 6 13 19 25 32 50 64 76 89 102 114 127 152 178 203 254 279 305 355 381 406
in. /4
1
/2
1 3
/4 1 11/4 2 21/2 3 31/2 4 41/2 5 6 7 8 10 11 12 14 15 16

packings & jointings


mm 0.4 0.75 1.5 3.2 5.0 6.5 8.0 9.5 11.0 12.5 16 19 22 25 32 40
in. 1
/64 1
/32 1
/16 1
/8 3
/16 /4
1 5
/16 3
/8 7
/16 1
/2 5
/8 3
/4 /8
7
1 1 /4
1
11/2

tapes
mm 1.5 3 6 25 32 40 50 65 75 100
in. 1
/16 /8
1
/4
1
1 1 /4
1
1 /2
1
2 2 /21
3 4

1.5
June 2010
unit conversions
length
engineering & technical data unit conversions

millimetre centimetre metre inch foot yard


mm cm m in ft yd
1 0.1 0.001 0.0394 0.0033 0.0011
10 1 0.01 0.3937 0.0328 0.0109
1000 100 1 39.3701 3.2808 1.0936
25.4 2.54 0.0254 1 0.0833 0.0278
304.8 30.48 0.3048 12 1 0.3333
914.4 91.44 0.9144 36 3 1

1 kilometre = 1000 metres = 0.62137 miles. 1 thou = 0.0254 mm.


1 mile = 1609.34 metres = 1.60934 kilometres. 1 m (micron) = 10 -6 m = 39.37 x 10 -6 in.

area
square millimetre square centimetre square metre square inch square foot square yard
mm 2 cm 2 m2 in 2 ft 2 yd 2
1 0.01 10 -6 1.55 x10 -3 1.076 x 10 -5 1.196 x 10 -6
100 1 10 -4
0.155 1.076 x 10 -3
1.196 x 10 -4
10 6 10 000 1 1550 10.764 1.196
645.16 6.4516 6.452 x 10 -4 1 6.944 x 10 -3 7.716 x 10 -4
92 903 929.03 0.093 144 1 0.111
836 127 8361.27 0.836 1296 9 1

volume
cubic millimetre cubic centimetre cubic metre cubic inch cubic foot cubic yard
mm 3 cm 3 m3 in 3 ft 3 yd 3
1 0.001 10 -9 6.1 x 10 -5 3.531 x 10 -8 1.308 x 10 -9
1000 1 10 -6 0.061 3.531 x 10 -5 1.308 x 10 -6
10 9
10 6
1 61 024 35.31 1.308
16 387 16.39 1.639 x 10 -5 1 5.787 x 10 -4 2.143 x 10 -5
2.832 x 107 2.832 x 10 4 0.0283 1728 1 0.0370
7.646 x 10 8 7.646 x 105 0.7646 46 656 27 1

liquid measure
cubic metre litre millilitre uk gallon us gallon cubic foot
m3 l ml UK gal US gal ft 3
1 1000 10 6 220 264.2 35.3147
0.001 1 1000 0.22 0.2642 0.0353
10 -6
0.001 1 2.2 x 10 -4
2.642 x 10 -4
3.53 x 10 -5
0.00455 4.546 4546 1 1.201 0.1605
0.00378 3.785 3785 0.8327 1 0.1337
0.0283 28.317 28 317 6.2288 7.4805 1

1 U.S. Barrel = 42 US gallons (petroleum measure). 1 litre = 10 6 mm3 = 10 3 cm3 or 1 cubic decimetre (1 dm3).
1 litre = 1.76 UK pints = 2.113 US pints. UK gallon and UK pint also called Imperial gallon and Imperial pint.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.6 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
unit conversions
velocity

engineering & technical data unit conversions


metre per second foot per second metre per minute foot per minute kilometre per hour mile per hour
m/s ft/s m/min ft/min km/h mile/h
1 3.281 60 196.85 3.6 2.2369
0.305 1 18.288 60 1.0973 0.6818
0.017 0.055 1 3.281 0.06 0.0373
0.005 0.017 0.305 1 0.0183 0.01136
0.278 0.911 16.667 54.68 1 0.6214
0.447 1.467 26.822 88 1.6093 1

mass
kilogram pound hundredweight tonne US ton
UK ton
kg lb cwt t sh ton
1 2.205 0.0197 0.001 9.84 x 10 -4 0.0011
0.454 1 0.0089 4.54 x 10 -4
4.46 x 10 -4
5.0 x 10 -4
50.802 112 1 0.0508 0.05 0.056
1000 2204.6 19.684 1 0.9842 1.1023
1016 2240 20 1.0161 1 1.12
907.2 2000 17.857 0.9072 0.8929 1

mass flow rate


kilogram/second pound per second kilogram/hour pound per hour UK ton per hour tonne per hour
kg/s lb/s kg/h lb/h ton/h t/h
1 2.205 3600 7936.64 3.5431 3.6
0.454 1 1633 3600 1.607 1.633
2.78 x 10 -4 6.12 x 10 -4 1 2.205 9.84 x 10 -4 0.001
1.26 x 10 -4
2.78 x 10 -4
0.454 1 4.46 x 10 -4
4.54 x 10 -4
0.282 0.622 1016 2240 1 1.016
0.278 0.612 1000 2204.6 0.9842 1

volumetric rate of flow

litre litre cubic metre cubic foot cubic foot UK gallon US gallon US barrel
per second per minute per hour per hour per minute per minute per minute per day
l/s l/min m 3 /h ft 3 /h ft 3 /min UK gal/min US gal/min US barrel/d
1 60 3.6 127.133 2.1189 13.2 15.85 543.439
0.017 1 0.06 2.1189 0.0353 0.22 0.264 9.057
0.278 16.667 1 35.3147 0.5886 3.666 4.403 150.955
0.008 0.472 0.0283 1 0.0167 0.104 0.125 4.275
0.472 28.317 1.6990 60 1 6.229 7.480 256.475
0.076 4.546 0.2728 9.6326 0.1605 1 1.201 41.175
0.063 3.785 0.2271 8.0209 0.1337 0.833 1 34.286
0.002 0.110 0.0066 0.2339 0.0039 0.024 0.029 1

1.7
June 2010
unit conversions
force
engineering & technical data unit conversions

newton kilonewton kilogram force* pound force


N kN kgf lbf
1 0.001 0.102 0.225
1000 1 101.97 224.81
9.807 0.0098 1 2.205
4.448 0.0044 0.454 1

* The kilogram force is sometimes called the kilopond (kp).

moment of force (torque)


pdl ft lbf in Nm lbf ft kgf m
1 0.3730 0.04214 0.03108 4.297 x 10 3
2.681 1 0.1130 0.08333 0.01152
23.73 8.851 1 0.7376 0.1020
32.17 12 1.356 1 0.1383
232.7 86.80 9.807 7.233 1
6006 2240 253.1 186.7 25.81
72070 26880 3037 2240 309.7

One Nm = 107 dyn cm (dyne centimetre).

power

Kilogram force foot pound


Watt metric horsepower
per second force per second
w horsepower hp
kgf m/s ft lbf/s
1 0.102 0.00136 0.738 0.0013
9.806 1 0.0133 7.233 0.0131
735.5 75 1 542.476 0.9863
1.356 0.138 1.84 x 10 -3
1 1.82 x 10 -3
745.70 76.04 1.0139 550.0 1

1 watt = 1 joule per sec = 1 newton metre per sec.


The metric horsepower is called cheval vapeur (ch) or (CV) in France.
In Germany it is called the Pferdestarke (PS).

ENERGY, WORK HEAT

joule kilojoule foot pound


megajoule British therm kilowatt
force thermal unit force
Mj Btu thm kW h
j kj ft lbf
1 0.001 10 -6 0.737 9.48 x 10 -4 9.48 x 10 -9 2.78 x 10 -7
1000 1 0.001 737.56 0.9478 9.48 x 10 -6
2.78 x 10 -4
10 6 1000 1 737 562 947.82 9.48 x 10 -3 0.2778
1.356 1.36 x 10 -3
1.36 x 10 -6
1 1.28 x 10 -3
1.28 x 10 -8
3.77 x 10 -7
1055.1 1.0551 1.05 x 10 -3 778.17 1 10 -5 2.931 x 10 -4
1.0551 x 10 8
105 510 105.51 7.78 x 10 7
100 000 1 29.307
3.6 x 10 6
3600 3.6 2.65 x 10 6
3412.1 0.03412 1

1 watt = 1 joule per sec = 1 newton metre per sec.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.8 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
unit conversions
pressure & liquid heat

engineering & technical data unit conversions


newton per bar kg force
KiloPascal pound per foot of metre of millimetre inch of
sq. metre or (10 5N/m 2) per sq.
(10 3Pa) sq. inch water water of mercury mercury
pascal (10 2kPa) centimetre
kPa lbf/in 2 ft H 2O m H 2O mm Hg in Hg
Nm 2 =Pa bar kgf/cm 2
1 0.001 10 -5 1.02 X 10 -5 1.45 X 10 -4 3.3 X 10 -4 1.02 X 10 -4 0.0075 2.95 X 10 -4
1000 1 0.01 1.02 X 10 -2 0.145 0.33 0.102 7.5 0.295
10 5
100 1 1.02 14.5 33.455 10.2 750.1 29.53
98067 98.067 0.981 1 14.22 32.808 10.0 735.6 28.96
6895 6.865 0.069 0.0703 1 2.307 0.703 51.71 2.036
2989 2.989 0.03 0.0305 0.433 1 0.305 22.42 0.883
9807 9.807 0.098 0.1 1.42 3.28 1 73.55 2.896
133.3 0.1333 0.0013 0.0014 0.019 0.045 0.014 1 0.039
3386 3.386 0.0338 0.0345 0.491 1.133 0.345 25.4 1

1 Pa = 1N/m2 1 mm Hg = 1 torr

*Example
Using Unit Conversion Tables: Convert 23 bar to ft H2O
Look up factor 1 in bar column, then accros to ft H2O column (33.455)
23 bar = 23 x 33.455 ft H2O
= 769.47 ft H2O

vacuum pressure chart

* Gauge unit values are shown as minus (-) values. This minus sign is not used in the specification table following normal industry practice.
Industrial vacuum = 1.33 x 10 -5 Absolute Bar = 29.89 in Hg vacuum.

1.9
June 2010
temperature conversions
engineering & technical data temperature conversions

-460 to 0 1 to 60 61 to 290 300 to 890 900 to 3000


C F \C F C F \C F C F \C F C F \C F C F \C F
-273 -459.4 -17.2 1 33.8 16.1 61 141.8 149 300 572 482 900 1652
-268 -450 -16.7 2 35.6 16.7 62 143.6 154 310 590 488 910 1670
-262 -440 -16.1 3 37.4 17.2 63 145.4 160 320 608 493 920 1688
-257 -430 -15.6 4 39.2 17.8 64 147.2 166 330 626 499 930 1706
-251 -420 -15.0 5 41.0 18.3 65 149.0 171 340 644 504 940 1724
-246 -410 -14.4 6 42.8 18.9 66 150.8 177 350 662 510 950 1742
-240 -400 -13.9 7 44.6 19.4 67 152.6 182 360 680 516 960 1760
-234 -390 -13.3 8 46.4 20.0 68 154.4 188 370 698 521 970 1778
-229 -380 -12.8 9 48.2 20.6 69 156.2 193 380 716 527 980 1796
-223 -370 -12.2 10 50.0 21.1 70 158.0 199 390 734 532 990 1814
-218 -360 -11.7 11 51.8 21.7 71 159.8 204 400 752 538 1000 1832
-212 -350 -11.1 12 53.6 22.2 72 161.6 210 410 770 549 1020 1868
-207 -340 -10.6 13 55.4 22.8 73 163.4 216 420 788 560 1040 1904
-201 -330 -10.0 14 57.2 23.3 74 165.2 221 430 806 571 1060 1940
-196 -320 -9.4 15 59.0 23.9 75 167.0 227 440 824 582 1080 1976
-190 -310 -8.9 16 60.8 24.4 76 168.8 232 450 842 593 1100 2012
-184 -300 -8.3 17 62.6 25.0 77 170.6 238 460 860 604 1120 2048
-179 -290 -7.8 18 64.4 25.6 78 172.4 243 470 878 616 1140 2084
-173 -280 -7.2 19 66.2 26.1 79 174.2 249 480 896 627 1160 2120
-169 -273 -460 -6.7 20 68.0 26.7 80 176.0 254 490 914 638 1180 2156
-168 -270 -454 -6.1 21 69.8 27.2 81 177.8 260 500 932 649 1200 2192
-162 -260 -436 -5.6 22 71.6 27.8 82 179.6 266 510 950 660 1220 2228
-157 -250 -418 -5.0 23 73.4 28.3 83 181.4 271 520 968 671 1240 2264
-151 -240 -400 -4.4 24 75.2 28.9 84 183.2 277 530 986 682 1260 2300
-146 -230 -382 -3.9 25 77.0 29.4 85 185.0 282 540 1004 693 1280 2336
-140 -220 -364 -3.3 26 78.8 30.0 86 186.8 288 550 1022 704 1300 2372
-134 -210 -346 -2.8 27 80.6 30.6 87 188.6 293 560 1040 732 1350 2462
-129 -200 -328 -2.2 28 82.4 31.1 88 190.4 299 570 1058 760 1400 2552
-123 -190 -310 -1.7 29 84.2 31.7 89 192.2 304 580 1076 788 1450 2642
-118 -180 -292 -1.1 30 86.0 32.2 90 194.0 310 590 1094 816 1500 2732
-112 -170 -274 -0.6 31 87.8 32.8 91 195.8 316 600 1112 843 1550 2822
-107 -160 -256 0.0 32 89.6 33.3 92 197.6 321 610 1130 871 1600 2912
-101 -150 -238 0.6 33 91.4 33.9 93 199.4 327 620 1148 899 1650 3002
-96 -140 -220 1.1 34 93.2 34.4 94 201.2 332 630 1166 927 1700 3092
-90 -130 -202 1.7 35 95.0 35.0 95 203.0 338 640 1184 954 1750 3182
-84 -120 -184 2.2 36 96.8 35.6 96 204.8 343 650 1202 982 1800 3272
-79 -110 -166 2.8 37 98.6 36.1 97 206.6 349 660 1220 1010 1850 3362
-73 -100 -148 3.3 38 100.4 36.7 98 208.4 354 670 1238 1038 1900 3452
-68 -90 -130 3.9 39 102.2 37.2 99 210.2 360 680 1256 1066 1950 3542
-62 -80 -112 4.4 40 104.0 37.8 100 212.0 366 690 1274 1093 2000 3632
-57 -70 -94 5.0 41 105.8 43 110 230 371 700 1292 1121 2050 3722
-51 -60 -76 5.6 42 107.6 49 120 248 377 710 1310 1149 2100 3812
-46 -50 -58 6.1 43 109.4 54 130 266 382 720 1328 1177 2150 3902
-40 -40 -40 6.7 44 111.2 60 140 284 388 730 1346 1204 2200 3992
-34 -30 -22 7.2 45 113.0 66 150 302 393 740 1364 1232 2250 4082
-29 -20 -4 7.8 46 114.8 71 160 320 399 750 1382 1260 2300 4172
-23 -10 14 8.3 47 116.6 77 170 338 404 760 1400 1288 2350 4262
-17.8 0 32 8.9 48 118.4 82 180 356 410 770 1418 1316 2400 4352
9.4 49 120.2 88 190 374 416 780 1436 1343 2450 4442
10.0 50 122.0 93 200 392 421 790 1454 1371 2500 4532
10.6 51 123.8 99 210 410 427 800 1472 1399 2550 4622
11.1 52 125.6 100 212 413.6 432 810 1490 1427 2600 4712
11.7 53 127.4 104 220 428 438 820 1508 1454 2650 4802
12.2 54 129.2 110 230 446 443 830 1526 1482 2700 4892
12.8 55 131.0 116 240 464 449 840 1544 1510 2750 4982
13.3 56 132.8 121 250 482 454 850 1562 1538 2800 5072
13.9 57 134.6 127 260 500 460 860 1580 1566 2850 5162
14.4 58 136.4 132 270 518 466 870 1598 1593 2900 5252
15.0 59 138.2 138 280 536 471 880 1616 1621 2950 5342
15.6 60 140.0 143 290 554 477 890 1634 1649 3000 5432
Locate temperature in middle column. If in degrees celsius, read Fahrenheit equivalent in right hand column: if in degrees Fahrenheit, read Celcius equivalent in
left hand column.

C = (5/9) x (F-32) = K-273 K = C+273 F = ((9/5) x C)+32 R = F+460

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.10 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
pressure ratings & flange compatibility
Flange Styles

engineering & technical data pressure ratings & flange compatibility


Welding Neck Slip-on Lap Joint Reducing

Blind Socket Type Welding Orifice Cop-a-Mate

Flange Standard Compatibility


The following flange standards are generally compatible:
AS2129 = ASB52 = BS10
ANSI = ASA
BS4504 = DIN2501

Australian Standard AS 2129 for Copper Alloy Australian Standard AS 2129 for Carbon Steel
Design Pressure (kPa)

Design Pressure (kPa)

Temperature (Deg C) Temperature (Deg C)

T/C 15-200mm 1200 kPa to 120C T/C 1200 kPa to 120C

1.11
June 2010
pressure ratings & flange compatibility
American Standard B16.5 (ASA) for B62 Copper Alloy American Standard B16.5 (ASA) for A105 (A216 WCB) Steel
engineering & technical data pressure ratings & flange compatibility

Temperature (Deg C) Temperature (Deg C)

Design Pressure (kPa)


Design Pressure (kPa)
Design Pressure (PSI)

Design Pressure (PSI)

Temperature (Deg F) Temperature (Deg F)

European Standard BS 4504 (DIN) for LG2C Copper Alloy European Standard BS 4504 (DIN) For BS 1503-161 28A
(BS1504-161B) Carbon Steel
Design Pressure (kPa)
Design Pressure (kPa)

Temperature (Deg C) Temperature (Deg C)

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.12 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to as2129

engineering & technical data flanges to as2129


Welding neck flange Blind flange Plate flange Boss flange Integral flange for pipes Raised face flange
and fittings

AS2129 1982 Table D


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES FLANGE THICKNESS
VARIATIONS
Nominal Diameter Bolt Number Diameter Bolt Size Raised Length Length Grey or SG Copper Alloy; Forged or
Pipe Size of Flange Circle of Bolt of Bolt Face of Boss of Weld iron; Boss or Blind, Plate, Wrought Steel;
Diameter Holes Holes Diameter Neck Integral Boss or Blind, Plate,
(1.6 mm) Flanges Integral Boss Welding
Thick Flanges Neck or
Integral
Flanges
A B C D E F G H I 2,3,5 I1 I 1,2,3,4,5
15 95 67 4 14 M12 47 10 22 13 6 5
20 100 73 4 14 M12 53 11 22 13 6 5
25 115 83 4 14 M12 65 11 22 13 8 5
32 120 87 4 14 M12 67 11 25 16 8 6
40 135 98 4 14 M12 78 13 29 16 10 6
50 150 114 4 18 M16 90 13 29 17 10 8
65 165 127 4 18 M16 103 16 32 17 11 8
80 185 146 4 18 M16 122 16 35 19 13 10
100 215 178 4 18 M16 154 19 41 19 16 10
125 255 210 8 18 M16 186 19 44 21 17 13
150 280 235 8 18 M16 211 19 48 21 17 13
200 335 292 8 18 M16 268 22 51 22 19 13
250 405 356 8 22 M20 328 27 64 25 19 16
300 455 406 12 22 M20 378 29 70 25 22 19
350 525 470 12 26 M24 438 73 29 25 22
400 580 521 12 26 M24 489 29 25 22
450 640 584 12 26 M24 532 32 29 25
500 705 641 16 26 M24 609 32 32 29
600 825 756 16 30 M27 720 35 35 32

All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

AS2129 1982 Table E


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES FLANGE THICKNESS
VARIATIONS
Nominal Diameter Bolt Number Diameter Bolt Size Raised Length Length Grey or Copper Copper Cast or
Pipe Size of Flange Circle of Bolt of Bolt Face of Boss of Weld SG iron; Alloy; Alloy; Wrought Steel;
Diameter Holes Holes Diameter Neck Boss or Plate, Boss Blind Blind, Plate,
(1.6 mm) Integral or Integral Boss Welding
Thick Flanges Flanges Neck or
Integral
Flanges
A B C D E F G H I 3,5 I 2,3,5 I1 I 1,2,3,4,5
15 95 67 4 14 M12 47 10 22 13 6 6 6
20 100 73 4 14 M12 53 11 22 13 6 6 6
25 115 83 4 14 M12 63 11 22 13 8 8 7
32 120 87 4 14 M12 67 11 25 16 8 8 8
40 135 98 4 14 M12 78 13 29 16 10 10 9
50 150 114 4 18 M16 90 13 29 19 10 10 10
65 165 127 4 18 M16 103 16 32 19 11 11 10
80 185 146 4 18 M16 122 16 35 19 13 13 11
100 215 178 8 18 M16 154 19 41 22 16 16 13
125 255 210 8 18 M16 186 19 44 22 17 17 14
150 280 235 8 22 M20 207 19 48 22 17 17 17
200 335 292 8 22 M20 264 22 51 25 19 20 19
250 405 356 12 22 M20 328 27 64 25 22 25 22
300 455 406 12 26 M24 374 29 70 29 25 28 25
350 525 470 12 26 M24 438 73 32 25 32 29
400 580 521 12 26 M24 489 32 25 36 32
450 640 584 16 26 M24 552 35 29 41 35
500 705 641 16 26 M24 609 38 32 46 38
600 825 756 16 33 M30 717 41 38 48

It is impracticable to use thicknesses less than 12.00mm for plate flanges.


All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

1.13
June 2010
flanges to as2129
engineering & technical data flanges to as2129

Welding neck flange Blind flange Plate flange Boss flange Integral flange for pipes Raised face flange
and fittings

AS2129 1982 Table f


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES FLANGE THICKNESS
VARIATIONS
Nominal Diameter Bolt Number Diameter Bolt Size Raised Length Length Grey or Copper Copper Cast or
Pipe Size of Flange Circle of Bolt of Bolt Face of Boss of Weld SG iron; Alloy; Alloy; Wrought Steel;
Diameter Holes Holes Diameter Neck Boss or Plate, Boss Blind Blind, Plate,
(1.6 mm) Integral or Integral Boss Welding
Thick Flanges Flanges Neck or
Integral
Flanges
A B C D E F G H I 3,5 I 2,3,5 I1 I 1,2,3,4,5
15 95 67 4 14 M12 47 10 22 13 8 8 10
20 100 73 4 14 M12 53 11 22 13 8 8 10
25 120 87 4 18 M16 63 11 29 13 10 10 10
32 135 98 4 18 M16 74 11 35 16 10 10 13
40 140 105 4 18 M16 81 13 35 16 11 11 13
50 165 127 4 18 M16 103 13 35 19 11 12 16
65 185 146 8 18 M16 122 16 38 19 13 13 16
80 205 165 8 18 M16 141 16 44 19 14 15 16
100 230 191 8 18 M16 167 19 51 22 17 17 19
125 280 235 8 22 M20 207 19 57 25 19 20 22
150 305 260 12 22 M20 232 19 57 25 22 23 22
200 370 324 12 22 M20 296 22 67 29 25 28 25
250 430 381 12 26 M24 349 27 73 29 25 32 29
300 490 438 16 26 M24 406 29 79 32 29 37 32
350 550 495 16 30 M27 459 86 35 32 42 35
400 610 552 20 30 M27 516 35 32 47 41
450 675 610 20 33 M30 571 38 35 52 44
500 735 673 24 33 M30 634 41 38 57 51
600 850 781 24 36 M33 739 44 41 68 57

It is impracticable to use thicknesses less than 12.00mm for plate flanges.


All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

AS2129 1982 Table h


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES FLANGE THICKNESS
VARIATIONS
Nominal Diameter Bolt Number Diameter Bolt Size Raised Length Length Grey or Copper Copper Cast or
Pipe Size of Flange Circle of Bolt of Bolt Face of Boss of Weld SG iron; Alloy; Alloy; Wrought Steel;
Diameter Holes Holes Diameter Neck Boss or Plate, Boss Blind Blind, Plate,
(1.6 mm) Integral or Integral Boss Welding
Thick Flanges Flanges Neck or
Integral
Flanges
A B C D E F G H I 3,5 I 2,3,5 I1 I 1,2,3,4,5
15 115 83 4 18 M16 57 10 29 16 10 11 13
20 115 83 4 18 M16 57 11 29 16 10 11 13
25 120 87 4 18 M16 64 11 29 19 11 12 14
32 135 98 4 18 M16 76 11 35 22 11 13 17
40 140 105 4 18 M16 83 13 35 22 13 14 17
50 165 127 4 18 M16 102 13 35 25 13 16 19
65 185 146 8 18 M16 114 16 38 25 14 17 19
80 205 165 8 18 M16 127 16 44 29 16 19 22
100 230 191 8 18 M16 152 19 51 32 19 23 25
125 280 235 8 22 M20 178 19 57 35 22 27 29
150 305 260 12 22 M20 210 19 57 35 25 30 29
200 370 324 12 22 M20 260 22 67 38 32 39 32
250 430 381 12 26 M24 311 27 73 41 35 45 35
300 490 438 16 26 M24 362 29 79 44 38 52 41
350 550 495 16 30 M27 419 86 48 41 58 48
400 610 552 20 30 M27 483 51 44 64 54
450 675 610 20 33 M30 533 54 48 71 60
500 735 673 24 33 M30 597 57 51 78 67
600 850 781 24 36 M33 699 64 57 92 76

It is impracticable to use thicknesses less than 12.00mm for plate flanges.


All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.14 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to as2129

engineering & technical data flanges to as2129


Welding neck flange Blind flange Plate flange Boss flange Integral flange for pipes Raised face flange
and fittings

AS2129 1982 Table J


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES FLANGE THICKNESS
VARIATIONS
Nominal Diameter Bolt Number Diameter Bolt Size Raised Length Length Grey or SG Copper Alloy; Cast or
Pipe Size of Flange Circle of Bolt of Bolt Face of Boss of Weld iron; Boss or Blind Wrought Steel;
Diameter Holes Holes Diameter Neck Integral Blind, Plate,
(1.6 mm) Flanges Boss Welding
Thick Neck or
Integral
Flanges
A B C D E F G H I 2,3,5 I1 I 1,2,3,4,5
15 115 83 4 18 M16 57 10 29 16 16 16
20 115 83 4 18 M16 57 11 29 16 16 16
25 120 87 4 18 M16 64 11 29 19 19 19
32 135 98 4 18 M16 76 11 35 19 19 19
40 140 105 4 18 M16 83 13 35 22 22 22
50 165 127 4 22 M20 102 13 35 25 25 25
65 185 146 8 22 M20 114 16 38 25 25 25
80 205 165 8 22 M20 127 16 44 32 32 32
100 230 191 8 22 M20 152 19 51 35 35 35
125 280 235 8 26 M24 178 19 57 38 38 38
150 305 260 12 26 M24 210 19 57 38 38 38
200 370 324 12 26 M24 260 67 41 46 41
250 430 381 12 30 M27 311 73 48
300 490 438 16 30 M27 362 79 51
350 550 495 16 33 M30 419 86 57
400 610 552 20 33 M30 483 64
450 675 610 20 36 M33 533 70
500 735 673 24 36 M33 597 79
600 850 781 24 39 M36 699 92

All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

AS2129 1982 Table k


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES FLANGE THICKNESS
VARIATIONS
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Length of Copper Copper Cast, Forged or
Pipe Size of Flange Diameter of Bolt of Bolt Face Weld Neck Alloy; Alloy; Wrought Steel;
Holes Holes Diameter Plate, or Blind Blind, Plate,
(1.6 mm) Integral Welding Neck
Thick Flanges or Integral
Flanges
A B C D E F H I 2,3,5 I1 I 1,2,3,4,5
15 115 83 4 18 M16 64 29 19 19 19
20 115 83 4 18 M16 64 29 19 19 19
25 125 95 4 18 M16 76 35 22 22 22
32 135 98 4 18 M16 76 35 22 22 22
40 150 114 4 22 M20 89 35 25 25 25
50 165 127 8 18 M16 102 35 25 25 25
65 185 146 8 22 M20 114 38 29 29 29
80 205 165 8 22 M20 127 44 32 32 32
100 240 197 8 26 M24 152 51 35 35 35
125 280 235 12 26 M24 178 57 41 41 41
150 305 260 12 26 M24 210 57 41 43 41
200 370 318 12 30 M27 260 67 48 52 48
250 430 381 16 30 M27 311 73 51
300 490 432 16 33 M30 362 83 57
350 570 508 16 36 M33 419 95 67
400 630 565 20 36 M33 483 - 76
450 720 654 20 39 M36 572 111 89
500 785 711 20 42 M39 622 117 98

All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

1.15
June 2010
flanges to as2129
engineering & technical data flanges to as2129

Welding neck flange Blind flange Plate flange Boss flange Integral flange for pipes Raised face flange
and fittings

AS2129 1982 Table r


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES
FLANGE VARIATIONS THICKNESS
Nominal Diameter Bolt Circle Number of Diameter of Bolt Size Raised Face Length of Cast, Forged or
Pipe Size of Flange Diameter Bolt Holes Bolt Holes Diameter Weld Neck Wrought Steel;
(1.6 mm) Thick Blind, Plate,
Welding Neck
or Integral
Flanges
A B C D E F H I 1,2,4,5
15 115 83 4 18 M16 64 29 19
20 115 83 4 18 M16 64 29 19
25 125 95 4 18 M16 76 35 22
32 135 98 4 18 M16 76 35 22
40 150 114 4 22 M20 89 35 25
50 165 127 8 18 M16 102 35 25
65 185 146 8 22 M20 114 38 29
80 205 165 8 22 M20 127 44 32
100 240 197 8 26 M24 152 51 35
125 280 235 12 26 M24 178 57 41
150 305 260 12 26 M24 210 67 44
200 370 324 12 30 M27 260 73 51
250 430 387 16 30 M27 311 92 60
300 510 457 16 33 M30 362 102 70
350 585 527 16 36 M33 419 114 79
400 640 584 20 36 M33 483 89
450 735 673 20 39 M36 572 137 98
500 805 730 20 42 M39 622 137 105

All dimensions are in mm. Available with or without raised face. Thickness dimension includes raised face.

AS2129 1982 Table s


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES
FLANGE VARIATIONS THICKNESS
Nominal Diameter Bolt Circle Number of Diameter of Bolt Size Raised Face Length of Cast, Forged or
Pipe Size of Flange Diameter Bolt Holes Bolt Holes Diameter Weld Neck Wrought Steel;
(1.6 mm) Thick Blind, Plate,
Welding Neck
or Integral
Flanges
A B C D E F H I 1,2,4,5
15 125 89 4 22 M20 64 38 22
20 125 89 4 22 M20 64 38 22
25 140 102 4 22 M20 76 44 25
32 145 108 4 22 M20 83 48 29
40 160 121 4 22 M20 89 51 29
50 170 133 8 22 M20 89 51 32
65 185 146 8 22 M20 102 54 32
80 205 165 8 26 M24 114 54 35
100 250 203 8 30 M27 159 60 41
125 285 235 12 26 M24 191 60 44
150 325 273 12 30 M27 210 76 51
200 415 356 12 36 M33 273 86 64
250 485 425 16 36 M33 330 111 79
300 580 508 16 42 M39 381 127 92
350 650 578 20 42 M39 438 143 105
400 745 660 20 48 M45 495 159 117

All dimensions are in mm. Thickness dimension includes raised face.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.16 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to as2129

engineering & technical data flanges to as2129


Welding neck flange Blind flange Plate flange Boss flange Integral flange for pipes Raised face flange
and fittings

AS2129 1982 Table t


DIMENSIONS OF FLANGE
DIMENSIONS COMMON TO ALL FLANGE TYPES
FLANGE VARIATIONS THICKNESS
Nominal Diameter Bolt Circle Number of Diameter of Bolt Size Raised Face Length of Cast, Forged or
Pipe Size of Flange Diameter Bolt Holes Bolt Holes Diameter Weld Neck Wrought Steel;
(1.6 mm) Thick Blind, Plate,
Welding Neck
or Integral
Flanges
A B C D E F H I 1,2,4,5
15 140 102 4 22 M20 64 38 25
20 140 102 4 22 M20 64 38 25
25 145 108 4 22 M20 76 44 29
32 160 121 4 26 M24 83 48 32
40 170 133 8 22 M20 89 51 35
50 185 146 8 22 M20 102 54 35
65 205 165 8 26 M24 114 60 41
80 235 191 8 30 M27 127 60 48
100 285 235 8 33 M30 159 76 57
125 325 273 12 33 M30 210 92 67
150 375 318 12 36 M33 229 102 73
200 475 406 12 42 M39 298 114 89
250 560 489 16 42 M39 356 146 108
300 655 572 16 48 M45 413 171 121

All dimensions are in mm. Thickness dimension includes raised face.

1.17
June 2010
flanges to ANSI B16.5
engineering & technical data flanges to ansi b16.5

Welding neck flange Blind flange Socket weld flange Lapped flange Slip-on weld flange Threaded

ansi b16.5 1981 class 150 (pn20); table asa 150


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Flange Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Thickness Slip On Flanges Flanges
Holes Holes Diameter Minimum or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 90 60.5 16 4 M14 34.9 11.5 16 16 48
20 () 98 70.0 16 4 M14 42.9 13.0 16 16 52
25 (1) 108 79.5 16 4 M14 50.8 14.5 17 17 56
32 (1) 117 89.0 16 4 M14 63.5 16.0 21 21 57
40 (1) 127 98.5 16 4 M14 73.0 17.5 22 22 62
50 (2) 152 120.5 20 4 M16 92.1 19.5 25 25 64
65 (2) 178 139.5 20 4 M16 104.8 22.5 29 29 70
80 (3) 191 152.5 20 4 M16 127.0 24.0 30 30 70
100 (4) 229 190.5 20 8 M16 157.2 24.0 32 33 76
125 (5) 254 216.0 23 8 M20 185.7 24.0 36 36 89
150 (6) 279 241.5 23 8 M20 215.9 25.5 49 40 89
200 (8) 343 298.5 23 8 M20 269.9 29.0 44 44 102
250 (10) 406 362.0 26 12 M24 323.8 30.5 49 49 102
300 (12) 483 432.0 26 12 M24 381.0 32.0 56 56 114
350 (14) 535 476.5 29 12 M27 412.8 35.0 57 79 127
400 (16) 600 540.0 29 16 M27 469.9 37.0 64 87 127
450 (18) 635 578.0 32 16 M30 533.4 40.0 68 97 140
500 (20) 700 635.0 32 20 M30 584.2 43.0 73 103 145
600 (24) 815 749.5 35 20 M33 692.2 48 83 111 152

All dimensions are in mm. Thickness dimension does not include raised face.

ansi b16.5 1981 class 300 (pn50); table asa 300


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Forged Steel Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Flanged Slip On Flanges Flanges
Holes Holes Diameter Thickness or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 95 66.5 16 4 M14 34.9 14.5 22 22 52
20 () 117 82.5 20 4 M18 42.9 16.0 25 25 57
25 (1) 124 89.0 20 4 M18 50.8 17.5 27 27 62
32 (1) 133 98.5 20 4 M18 63.5 19.5 27 27 65
40 (1) 156 114.5 23 4 M20 73.0 21.0 30 30 68
50 (2) 165 127.0 20 8 M18 92.1 22.5 33 33 70
65 (2) 191 149.0 23 8 M20 104.8 25.5 38 38 76
80 (3) 210 168.5 23 8 M20 127.0 29.0 43 43 79
100 (4) 254 200.0 23 8 M20 157.2 32.0 48 48 86
125 (5) 279 235.0 23 8 M20 185.7 35.0 51 51 98
150 (6) 318 270.0 23 12 M20 215.9 37.0 52 52 98
200 (8) 381 330.0 26 12 M24 269.9 41.5 62 62 111
250 (10) 445 387.5 29 16 M27 323.8 48.0 67 95 117
300 (12) 520 451.0 32 16 M30 381.0 51.0 73 102 130
350 (14) 585 514.5 32 20 M30 412.8 54.0 76 111 143
400 (16) 650 571.5 35 20 M33 469.9 57.5 83 121 146
450 (18) 710 628.5 35 24 M33 533.4 60.5 89 130 159
500 (20) 775 686.0 35 24 M33 584.2 63.5 95 140 162
600 (24) 915 813.0 42 24 M39 692.2 70.0 106 152 168

All dimensions are in mm. Thickness dimension does not include raised face.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.18 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to ANSI B16.5

engineering & technical data flanges to ansi b16.5


Welding neck flange Blind flange Socket weld flange Lapped flange Slip-on weld flange Threaded

ansi b16.5 1981 class 400 (pn68); table asa 400


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Forged Steel Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Flanged Slip On Flanges Flanges
Holes Holes Diameter Thickness or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 95 66.5 16 4 M14 34.9 14.5 22 22 52
20 () 117 82.5 20 4 M18 42.9 16.0 25 25 57
25 (1) 124 89.0 20 4 M18 50.8 17.5 27 27 62
32 (1) 133 98.5 20 4 M18 63.5 21.0 29 29 67
40 (1) 156 114.5 23 4 M20 73.0 22.5 32 32 70
50 (2) 165 127.0 23 8 M20 92.1 25.5 37 37 73
65 (2) 191 149.0 23 8 M20 104.8 29.0 41 41 79
80 (3) 210 168.0 23 8 M20 127.0 32.0 46 46 83
100 (4) 254 200.0 26 8 M24 157.2 35.0 51 51 89
125 (5) 279 235.0 26 8 M24 185.7 38.5 54 54 102
150 (6) 318 270.0 26 12 M24 215.9 41.5 57 57 103
200 (8) 381 330.0 30 12 M27 269.9 48.0 68 68 118
250 (10) 445 387.5 33 16 M30 323.8 54.0 73 102 124
300 (12) 520 451.0 36 16 M33 381.0 57.5 79 108 136
350 (14) 585 514.5 36 20 M33 412.8 60.5 84 117 149
400 (16) 650 571.5 39 20 M36 469.9 63.5 94 127 152
450 (18) 710 628.5 39 24 M36 533.4 67.0 98 137 165
500 (20) 775 686.0 42 24 M39 584.2 70.0 102 146 168
600 (24) 915 813.0 48 24 M45 692.2 76.5 114 159 175

All dimensions are in mm. Thickness dimension does not include raised face.

ansi b16.5 1981 class 600 (pn100); table asa 600


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Forged Steel Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Flanged Slip On Flanges Flanges
Holes Holes Diameter Thickness or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 95 66.5 16 4 M14 34.9 14.5 22 22 52
20 () 117 82.5 20 4 M18 42.9 16.0 25 25 57
25 (1) 124 89.0 20 4 M18 50.8 17.5 27 27 62
32 (1) 133 98.5 20 4 M18 63.5 21.0 29 29 67
40 (1) 156 114.5 23 4 M20 73.0 22.5 32 32 70
50 (2) 165 127.0 23 8 M20 92.1 25.5 37 37 73
65 (2) 191 149.0 23 8 M20 104.8 29.0 41 41 79
80 (3) 210 168.0 23 8 M20 127.0 32.0 46 46 83
100 (4) 273 216.0 26 8 M24 157.2 38.5 54 54 102
125 (5) 330 267.0 29 8 M27 185.7 44.5 60 60 114
150 (6) 356 292.0 29 12 M27 215.9 48.0 67 67 117
200 (8) 419 349.0 32 12 M30 269.9 55.5 76 76 133
250 (10) 510 432.0 35 16 M33 323.8 63.5 86 111 152
300 (12) 560 489.0 35 20 M33 381.0 67.0 92 117 156
350 (14) 605 527.0 39 20 M36 412.8 70.0 94 127 165
400 (16) 685 603.0 42 20 M39 469.9 76.5 106 140 178
450 (18) 745 654.0 45 20 M42 533.4 83.0 117 152 184
500 (20) 815 724.0 45 24 M42 584.2 89.0 127 165 190
600 (24) 940 838.0 51 24 M48 692.2 102.0 140 184 203

All dimensions are in mm. Thickness dimension does not include raised face.

1.19
June 2010
flanges to ANSI B16.5
engineering & technical data flanges to ansi b16.5

Welding neck flange Blind flange Socket weld flange Lapped flange Slip-on weld flange Threaded

ansi b16.5 1981 class 900 (pn150); table asa 900


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Forged Steel Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Flanged Slip On Flanges Flanges
Holes Holes Diameter Thickness or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 121 82.5 23 4 M20 34.9 22.5 32 32 60
20 () 130 89.0 23 4 M20 42.9 25.5 35 35 70
25 (1) 149 101.5 26 4 M24 50.8 29.0 41 41 73
32 (1) 159 111.0 26 4 M24 63.5 29.0 41 41 73
40 (1) 178 124.0 29 4 M27 73.0 32.0 44 44 83
50 (2) 216 165.0 26 8 M24 92.1 38.5 57 57 102
65 (2) 244 190.5 29 8 M27 104.8 41.5 64 64 105
80 (3) 241 190.5 26 8 M24 127.0 38.5 54 54 102
100 (4) 292 235.0 32 8 M30 157.2 44.5 70 70 114
125 (5) 349 279.5 35 8 M33 185.7 51.0 79 79 127
150 (6) 381 317.5 32 12 M30 215.9 56.0 86 86 140
200 (8) 470 393.5 39 12 M36 269.9 63.5 102 114 162
250 (10) 545 470.0 39 16 M36 323.8 70.0 108 127 184
300 (12) 610 533.5 39 20 M36 381.0 79.5 117 143 200
350 (14) 640 559.0 42 20 M39 412.8 86.0 130 156 213
400 (16) 705 616.0 45 20 M42 469.9 89.0 133 165 216
450 (18) 785 686.0 51 20 M48 533.4 102.0 152 191 229
500 (20) 855 749.5 54 20 M52 584.2 108.0 159 210 248
600 (24) 1040 901.5 67 20 M64 692.2 140.0 203 287 292

All dimensions are in mm. Thickness dimension does not include raised face.

ansi b16.5 1981 class 1500 (pn250); table asa 1500


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Forged Steel Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Flanged Slip On Flanges Flanges
Holes Holes Diameter Thickness or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 121 82.5 23 4 M20 34.9 22.5 32 32 60
20 () 130 89.0 23 4 M20 42.9 25.5 35 35 70
25 (1) 149 101.5 26 4 M24 50.8 29.0 41 41 73
32 (1) 159 111.0 26 4 M24 63.5 29.0 41 41 73
40 (1) 178 124.0 29 4 M27 73.0 32.0 44 44 83
50 (2) 216 165.0 26 8 M24 92.1 38.5 57 57 102
65 (2) 244 190.5 29 8 M27 104.8 41.5 64 64 105
80 (3) 267 203.0 32 8 M30 127.0 48.0 73 73 118
100 (4) 311 241.5 35 8 M33 157.2 54.0 90 90 124
125 (5) 375 292.0 42 8 M39 185.7 73.5 105 105 155
150 (6) 394 317.5 39 12 M36 215.9 83.0 119 119 171
200 (8) 483 393.5 45 12 M42 269.9 92.0 143 143 213
250 (10) 585 482.5 51 12 M48 323.8 108.0 159 178 254
300 (12) 675 571.5 54 16 M52 381.0 124.0 181 219 283
350 (14) 750 635.0 61 16 M56 412.8 133.5 241 298
400 (16) 825 705.0 67 16 M64 469.9 146.5 260 311
450 (18) 915 774.5 74 16 M72 533.4 162.0 276 327
500 (20) 985 832.0 80 16 M78 584.2 178.0 292 356
600 (24) 1170 990.5 93 16 M90 692.2 203.5 330 406

All dimensions are in mm. Thickness dimension does not include raised face.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.20 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to ANSI B16.5

engineering & technical data flanges to ansi b16.5


Welding neck flange Blind flange Socket weld flange Lapped flange Slip-on weld flange Threaded

ansi b16.5 1981 class 2500 (pn420); table asa 2500


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Diameter Number Bolt Size Raised Forged Steel Threaded, Lapped Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Flanged Slip On Flanges Flanges
Holes Holes Diameter Thickness or Socket
(1.6 mm) Welding
Thick Flanges

mm (in) A B C D E F G H I J
15 () 133 89.0 23 4 M20 34.9 30.5 40 40 73.0
20 () 140 95.0 23 4 M20 42.9 32.0 43 43 79.4
25 (1) 159 108.0 26 4 M24 50.8 35.0 48 48 88.9
32 (1) 184 130.0 29 4 M27 63.5 38.5 52 52 95.2
40 (1) 203 146.0 32 4 M30 73.0 44.5 60 60 111.4
50 (2) 235 171.5 29 8 M27 92.1 51.0 70 70 127.0
65 (2) 267 197.0 32 8 M30 104.8 57.5 79 79 142.9
80 (3) 305 228.5 35 8 M33 127.0 67.0 92 92 168.2
100 (4) 356 273.0 42 8 M39 157.2 76.5 108 108 190.5
125 (5) 419 324.0 48 8 M45 185.7 92.5 130 130 228.6
150 (6) 483 368.5 54 8 M52 215.9 108.0 152 152 273.0
200 (8) 550 438.0 54 12 M52 269.9 127.0 178 178 317.5
250 (10) 675 539.5 67 12 M64 323.8 165.5 229 229 419.4
300 (12) 760 619.0 74 12 M72 381.0 184.5 254 254 635.0

All dimensions are in mm. Thickness dimension does not include raised face.

1.21
June 2010
flanges to bs4504; DIN*
engineering & technical data flanges to bs4504; din*

Welding neck Blind Bossed Plate slip-on welding

bs4504 1969; DIN*; table 6


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck Bossed
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H I J
15 () 80 55 4 11 M10 40 2 12 30 20
20 () 90 65 4 11 M10 50 2 14 32 24
25 (1) 100 75 4 11 M10 60 2 14 35 24
32 (1) 120 90 4 14 M12 70 2 16 35 26
40 (1) 130 100 4 14 M12 80 3 16 38 26
50 (2) 140 110 4 14 M12 90 3 16 38 28
65 (2) 160 130 4 14 M12 110 3 16 38 32
80 (3) 190 150 4 18 M16 128 3 18 42 34
100 (4) 210 170 4 18 M16 148 3 18 45 40
125 (5) 240 200 8 18 M16 178 3 20 48 44
150 (6) 265 225 8 18 M16 202 3 20 48 44
200 (8) 320 280 8 18 M16 258 3 22 55 44
250 (10) 375 335 12 18 M16 312 3 24 60 44
300 (12) 440 395 12 22 M20 365 4 24 62 44
350 (14) 490 445 12 22 M20 415 4 26 62
400 (16) 540 495 16 22 M20 465 4 28 65
450 (18) 595 550 16 22 M20 520 4 30 65
500 (20) 645 600 20 22 M20 570 4 30 68
600 (24) 755 705 20 26 M24 670 5 32 70

All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

bs4504 1969; DIN*; table 10


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck Bossed
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H I J
15 () 95 65 4 14 M12 45 2 14 35 20
20 () 105 75 4 14 M12 58 2 16 38 24
25 (1) 115 85 4 14 M12 68 2 16 38 24
32 (1) 140 100 4 18 M16 78 2 16 40 26
40 (1) 150 110 4 18 M16 88 3 16 42 26
50 (2) 165 125 4 18 M16 102 3 18 45 28
65 (2) 185 145 4 18 M16 122 3 18 45 32
80 (3) 200 160 8 18 M16 138 3 20 50 34
100 (4) 220 180 8 18 M16 158 3 20 52 40
125 (5) 250 210 8 18 M16 188 3 22 55 44
150 (6) 285 240 8 22 M20 212 3 22 55 44
175 (7) 315 270 8 22 M20 242 3 24 60
200 (8) 340 295 8 22 M20 268 3 24 62 44
250 (10) 395 350 12 22 M20 320 3 26 68 46
300 (12) 445 400 12 22 M20 370 4 26 68 46
350 (14) 505 460 16 22 M20 430 4 28 68
400 (16) 565 515 16 26 M24 482 4 32 72
450 (18) 615 565 20 26 M24 532 4 36 72
500 (20) 670 620 20 26 M24 585 4 38 75
600 (24) 780 725 20 30 M27 685 5 42 80

*BS4504 is basically the British equivalent to the DIN flange standards.


All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.22 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to bs4504; DIN*

engineering & technical data flanges to bs4504; din*


Welding neck Blind Bossed Plate slip-on welding

bs4504 1969; DIN*; table 16


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck Bossed
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H I J
15 () 95 65 4 14 M12 45 2 14 35 20
20 () 105 75 4 14 M12 58 2 16 38 24
25 (1) 115 85 4 14 M12 68 2 16 38 24
32 (1) 140 100 4 18 M16 78 2 16 40 26
40 (1) 150 110 4 18 M16 88 3 16 42 26
50 (2) 165 125 4 18 M16 102 3 18 45 28
65 (2) 185 145 4 18 M16 122 3 18 45 32
80 (3) 200 160 8 18 M16 138 3 20 50 34
100 (4) 220 180 8 18 M16 158 3 20 52 40
125 (5) 250 210 8 18 M16 188 3 22 55 44
150 (6) 285 240 8 22 M20 212 3 22 55 44
175 (7) 315 270 8 22 M20 242 3 24 60
200 (8) 340 295 12 22 M20 268 3 24 62 44
250 (10) 405 355 12 26 M24 320 3 26 70 46
300 (12) 460 410 12 26 M24 378 4 28 78 46
350 (14) 520 470 16 26 M24 438 4 32 82
400 (16) 580 525 16 30 M27 490 4 36 85
450 (18) 640 585 20 30 M27 550 4 40 87
500 (20) 715 650 20 33 M30 610 4 44 90
600 (24) 840 770 20 36 M33 725 5 52 95

All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

bs4504 1969; DIN*; table 25


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck Bossed
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H I J
15 () 95 65 4 14 M12 45 2 16 38 22
20 () 105 75 4 14 M12 58 2 18 40 26
25 (1) 115 85 4 14 M12 68 2 18 40 28
32 (1) 140 100 4 18 M16 78 2 18 42 30
40 (1) 150 110 4 18 M16 88 3 18 45 32
50 (2) 165 125 4 18 M16 102 3 20 48 34
65 (2) 185 145 8 18 M16 122 3 22 52 38
80 (3) 200 160 8 18 M16 138 3 24 58 40
100 (4) 235 190 8 22 M20 162 3 26 65 44
125 (5) 270 220 8 26 M24 188 3 28 68 48
150 (6) 300 250 8 26 M24 218 3 30 75 52
175 (7) 330 280 12 26 M24 248 3 26 75
200 (8) 360 310 12 26 M24 278 3 28 80 52
250 (10) 425 370 12 30 M27 335 3 32 88 60
300 (12) 485 430 16 30 M27 395 4 38 92 67
350 (14) 555 490 16 33 M30 450 4 42 100
400 (16) 620 550 16 36 M33 505 4 46 110
450 (18) 670 600 20 36 M33 555 4 52 110
500 (20) 730 660 20 36 M33 615 4 58 125
600 (24) 845 770 20 39 M36 720 5 66 125

*BS4504 is basically the British equivalent to the DIN flange standards.


All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

1.23
June 2010
flanges to bs4504; DIN*
engineering & technical data flanges to bs4504; din*

Welding neck Blind Bossed Plate slip-on welding

bs4504 1969; DIN*; table 40


DIMENSIONS COMMON TO ALL FLANGE TYPES LENGTH THROUGH HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck Bossed
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H I J
15 () 95 65 4 14 M12 45 2 16 38 22
20 () 105 75 4 14 M12 58 2 18 40 26
25 (1) 115 85 4 14 M12 68 2 18 40 28
32 (1) 140 100 4 18 M16 78 2 18 42 30
40 (1) 150 110 4 18 M16 88 3 18 45 32
50 (2) 165 125 4 18 M16 102 3 20 48 34
65 (2) 185 145 8 18 M16 122 3 22 52 38
80 (3) 200 160 8 18 M16 138 3 24 58 40
100 (4) 235 190 8 22 M20 162 3 26 65 44
125 (5) 270 220 8 26 M24 188 3 28 68 48
150 (6) 300 250 8 26 M24 218 3 30 75 52
175 (7) 350 295 12 30 M27 260 3 32 82
200 (8) 375 320 12 30 M27 285 3 34 88 52
250 (10) 450 385 12 33 M30 345 3 42 105 60
300 (12) 515 450 16 33 M30 410 4 50 115 67
350 (14) 580 510 16 36 M33 465 4 56 125
400 (16) 660 585 16 39 M36 535 4 64 135
450 (18) 685 610 20 39 M36 560 4 68 135
500 (20) 755 670 20 42 M39 615 4 72 140

All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

bs4504 1969; DIN*; table 64


LENGTH
DIMENSIONS COMMON TO ALL FLANGE TYPES THROUGH
HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H J
15 () 105 75 4 14 M12 45 2 20 45
20 () 130 90 4 18 M16 58 2 22 58
25 (1) 140 100 4 18 M16 68 2 24 58
32 (1) 155 110 4 22 M20 78 2 24 60
40 (1) 170 125 4 22 M20 88 3 26 62
50 (2) 180 135 4 22 M20 102 3 26 62
65 (2) 205 160 8 22 M20 122 3 26 68
80 (3) 215 170 8 22 M20 138 3 30 72
100 (4) 250 200 8 26 M24 162 3 32 78
125 (5) 295 240 8 30 M27 188 3 34 88
150 (6) 345 280 8 33 M30 218 3 36 95
175 (7) 375 310 12 33 M30 260 3 40 105
200 (8) 415 345 12 36 M33 285 3 46 110
250 (10) 470 400 12 36 M33 345 3 54 125
300 (12) 530 460 16 36 M33 410 4 62 140
350 (14) 600 525 16 39 M36 465 4 72 150
400 (16) 670 585 16 42 M39 535 4 78 160

*BS4504 is basically the British equivalent to the DIN flange standards.


All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.24 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.
flanges to bs4504; DIN*

engineering & technical data flanges to bs4504; din*


Welding neck Blind Bossed Plate slip-on welding

bs4504 1969; DIN*; table 100


LENGTH
DIMENSIONS COMMON TO ALL FLANGE TYPES THROUGH
HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H J
15 () 105 75 4 14 M12 45 2 20 45
20 () 130 90 4 18 M16 58 2 22 58
25 (1) 140 100 4 18 M16 68 2 24 58
32 (1) 155 110 4 22 M20 78 2 24 60
40 (1) 170 125 4 22 M20 88 3 26 62
50 (2) 195 145 4 26 M24 102 3 28 68
65 (2) 220 170 8 26 M24 122 3 30 76
80 (3) 230 180 8 26 M24 138 3 34 78
100 (4) 265 210 8 30 M27 162 3 36 90
125 (5) 315 250 8 33 M30 188 3 42 105
150 (6) 355 290 12 33 M30 218 3 48 115
175 (7) 385 320 12 33 M30 260 3 54 127
200 (8) 430 360 12 36 M33 285 3 60 130
250 (10) 505 430 12 39 M36 345 3 72 157
300 (12) 585 500 16 42 M39 410 4 84 170
350 (14) 655 560 16 48 M45 465 4 95 189
400 (16) 715 620 16 48 M45 535 4 106
500 (20) 870 760 20 56 M54 615 4 128

*BS4504 is basically the British equivalent to the DIN flange standards.


All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

bs4504 1969; DIN*; table 160


LENGTH
DIMENSIONS COMMON TO ALL FLANGE TYPES THROUGH
HUB
Nominal Diameter Bolt Circle Number Diameter Bolt Size Raised Raised Flange Weld Neck
Pipe Size of Flange Diameter of Bolt of Bolt Face Face Thickness Flanges
Holes Holes Diameter Thickness

mm (in) A B C D E F G H J
15 () 105 75 4 14 M12 45 2 24 45
20 () 130 90 4 18 M16 58 2 26 58
25 (1) 140 100 4 18 M16 68 2 26 58
32 (1) 155 110 4 22 M20 78 2 28 60
40 (1) 170 125 4 22 M20 83 3 30 64
50 (2) 195 145 4 26 M24 102 3 34 75
65 (2) 220 170 8 26 M24 122 3 36 82
80 (3) 230 180 8 26 M24 138 3 40 86
100 (4) 265 210 8 30 M27 162 3 44 100
125 (5) 315 250 8 33 M30 188 3 54 115
150 (6) 355 290 12 33 M30 218 3 62 128
175 (7) 390 320 12 36 M33 260 3 68 138
200 (8) 430 360 12 36 M33 285 3 76 140
250 (10) 515 430 12 42 M39 345 3 90 155
300 (12) 585 500 16 42 M39 410 4 106 175

*BS4504 is basically the British equivalent to the DIN flange standards.


All dimensions are in mm. Available with or without raised face. Thickness dimension does not include raised face.

1.25
June 2010
hex head bolt & nut or bolt only dimensions
engineering & technical data hex head bolt & nut or bolt only dimensions

NB 2 x E Flanges Hyflo Wafer Hyflo Wafer Hyflo Lugged


cop-a-mate or steel Check Valve butterfly valve butterfly valve
size
No. : Size No. : Size No. : Size No. : Size
15 4 : M12 x 50
Code: 012423
20 4 : M12 x 50
Code: 012423
25 4 : M12 x 50
Code: 012423
32 4 : M12 x 50
Code: 012423
40 4 : M12 x 50 4 : M12 X 100
Code: 012423 Code: 012614
50 4 : M16 x 60 4 : M16 x 100 4 : M16 x 100 8 : M16 x 30
Code: 021767 Code: 012633 Code: 012633 Code: 021763
65 4 : M16 x 60 4 : M16 x 100 4 : M16 x 100 8 : M16 x 35
Code: 021767 Code: 012633 Code: 012633 Code: 021764
80 4 : M16 x 60 4 : M16 x 120 4 : M16 x 100 8 : M16 x 35
Code: 021767 Code: 012634 Code: 012633 Code: 021764
100 8 : M16 x 65 8 : M16 x 130 8 : M16 x 110 16 : M16 x 40
Code: 021768 Code: 012635 Code: 012303 Code: 021765
125 8 : M16 x 65 8 : M16 x 130 8 : M16 x 110 16 : M16 x 40
Code: 021768 Code: 012635 Code: 012303 Code: 021765
150 8 : M20 x 75 8 : M20 x 150 8 : M20 x 130 16 : M20 x 45
Code: 012848 Code: 012657 Code: 012359 Code: 021904
200 8 : M20 x 80 8 : M20 x 180 8 : M20 x 130 16 : M20 x 50
Code: 020644 Code: 012875 Code: 012359 Code: 021905
250 12 : M20 x 80 12 : M20 x 200 12 : M20 x 150 24 : M20 x 55
Code: 020644 Code: 012657 Code: 021906
300 12 : M24 x 100 12 : M24 x 220 12 : M24 x 175 24 : M24 x 65
Code: 012638* Code: 012747* Code: 012608*
350 12 : M24 x 100 12 : M24 x 230 12 : M24 x 200 24 : M24 x 65
Code: 012638* Code: 012738* Code: 012608*
400 12 : M24 x 110 12 : M24 x 225 24 : M24 x 80
Code: 012648* Code: 012609*
450 16 : M24 x 110 16 : M24 x 250 32 : M24 x 90
Code: 012648* Code: 012619*
500 16 : M24 x 120 16 : M24 x 250 32 : M24 x 100

600 16: M30 x 140 16 : M30 x 300 32 : M30 x 115


Codes are all bolts and nut.
The use of zinc plated or galvanised bolts and nuts is recommended.
Galvanised threads need checking for compatibility with lugged butterfly valves.
* Galvanised nuts and bolts, other codes are zinc plated nuts and bolts.
NB. Bolt lengths allow for inclusion of washers.

The information provided in this catalogue is based on original manufacturers designs and specifications and subject to change without
1.26 notice. Crane Distribution accepts no liability for the accuracy of the information or the availability of products.

You might also like