Professional Documents
Culture Documents
Manual de instrucciones
ZOOM Corporation
Est prohibida la reproduccin total o parcial de
este manual por cualquier sistema.
speG9.book Page 2 Thursday, March 16, 2006 9:52 PM
Alimentacin
Precauciones de uso
Utilice solo un adaptador CA que le proporcione a la
Atencin
unidad 15 V DC, 1.5A (Zoom AD-0012). El uso de Interferencias elctricas
cualquier otro tipo de adaptador podra daar la unidad Por motivos de seguridad, el G9.2tt ha sido diseado para
e incluso suponer un riesgo para su propia seguridad.
ofrecer la mxima proteccin contra las radiaciones
Conecte el adaptador CA solo a una salida con el tipo
de voltaje que requiera el adaptador.
electromagnticas emitidas desde dentro de la unidad, y ante
Para desconectar el adaptador CA de la salida de interferencias exteriores. No obstante, no debe colocar cerca
corriente, tire del adaptador y no del cable. del G9.2tt aparatos que sean susceptibles a las interferencias o
Durante las tormentas o cuando no vaya a utilizar la unidad que emitan ondas electromagnticas potentes, ya que la
durante algn tiempo, desenchufe el adaptador CA. posibilidad de dichas interferencias nunca puede ser
No pise el cable de alimentacin,ni lo retuerza, ni eliminada por completo.
coloque objetos pesados sobre l.
Con cualquier tipo de unidad de control digital, incluyendo el
Entorno G9.2tt, las interferencias electromagnticas pueden producir
Atencin
Para evitar incendios, descargas elctricas o averas errores y daar o destruir los datos. Trate de reducir al
del aparato, evite utilizar el G9.2tt en entornos en los mnimo este riesgo de daos.
que pueda quedar expuesto a:
Limpieza
Temperaturas excesivas Use un trapo suave y seco para limpiar el G9.2tt. Si es
Fuentes de calor como radiadores o calefactores
necesario, humedezca ligeramente el trapo. No utilice nunca
Altos niveles de humedad
Niveles de polvo o arena muy elevados
limpiadores abrasivos, ceras o disolventes (como el aguarrs
Vibraciones o golpes excesivos o el alcohol de quemar) dado que pueden daar el acabado de
la superficie.
Deje libre un espacio de 5 cm como mnimo
alrededor de la unidad para su correcta ventilacin.
No bloquee las ranuras de ventilacin con peridicos Tenga siempre a mano este manual para
o cortinas. cualquier referencia en el futuro.
2 ZOOM G9.2tt
speG9.book Page 3 Thursday, March 16, 2006 9:52 PM
Indice
PRECAUCIONES DE SEGURIDAD Uso del bucle de efectos ......................... 41
Precauciones de uso ...............................2 Ejemplos de usos del sistema MIDI .......43
Caractersticas ...........................................4 Lo que puede hacer con el MIDI .......... 43
Trminos utilizados en este manual .........5 Seleccin del canal MIDI ....................... 43
Controles y funciones ................................6 Envo y recepcin de informacin de
Conexiones .................................................8 cambio de programa va MIDI
Encendido ...................................................9 (cambio de programa) ......................... 44
Gua rpida 1 (Funcionamiento del modo Envo y recepcin de informacin de
de reproduccin/modo manual) ...........10 funcionamiento de pedal/pedal de
Gua rpida 2 (Funcionamiento del modo disparo/tecla va MIDI
de edicin/grabacin) ............................12 (cambio de control) .............................. 47
Seleccin de programas para su reproduccin Envo y recepcin de datos internos
(modo de reproduccin) .......................14 del G9.2tt va MIDI ................................. 50
Pantalla del panel ................................... 14 Otras funciones ........................................ 52
Seleccin de un programa .................... 14 Uso de la funcin ARRM ....................... 52
Ajuste del sonido ................................... 15 Uso del G9.2tt como interface audio
Uso del Accelerator ............................... 16 para un ordenador ................................ 54
Uso del Energizer ................................... 17 Anulacin de la salida directa cuando est
Activacin y desactivacin de mdulos con el pie usando una conexin USB .................. 55
durante la reproduccin (modo manual) .......19 Acerca de los programas editores/
Uso del afinador interno biblioteca ............................................... 56
(estado bypass/anulacin) ....................21 Ajuste del contraste de la pantalla ....... 56
Uso del afinador cromtico ................... 21 Enlace de efectos ..................................... 57
Uso de otros tipos de afinador .............. 22 Cambio entre el sonido en vivo y el sonido
Modificacin del sonido de un programa de grabacin directa ............................ 57
(modo de edicin) ..................................24 Uso de la funcin de seleccin de
Configuracin de programas ................. 24 amplificador .......................................... 58
Pasos bsicos del modo de edicin ...... 24 Cambio de la posicin de insercin de la
Cambio de nombre de un programa ..... 27 seccin de pre-amplificacin y del
Grabacin de programas y bancos mdulo WAH/EFX1 ............................... 58
(modo de grabacin) ..............................28 Tipos de efectos y parmetros ............... 60
Grabacin/intercambio de programas ..... 28 Cmo leer la tabla de parmetros ........ 60
Grabacin/intercambio de bancos ....... 29 Mdulo COMP .............................................61
Reinicializacin de los programas a los Mdulo WAH/EFX1 ......................................61
ajustes de fbrica ................................. 29 Mdulo EXT LOOP (bucle externo) .............64
Mdulo ZNR ................................................64
Uso de los pedales de expresin ............31 Mdulo PRE AMP ........................................65
Acerca de los pedales de expresin ..... 31 Mdulo EQ ...................................................67
Asignacin de destinos de control al Mdulo CABINET ........................................67
pedal de expresin 1 ............................. 32 Mdulo MOD/EFX2 .....................................67
Asignacin de destinos de control al Mdulo DELAY ............................................72
pedal de expresin 2 ............................. 33 Mdulo REVERB ..........................................73
Ajuste de los pedales de expresin ...... 35 Mdulo TOTAL ............................................75
Uso del pedal de disparo de funcin ...........38 Resolucin de problemas ........................ 76
Ajuste del tempo de un programa ......... 39 Especificaciones tcnicas ...................... 77
Tabla de implementacin MIDI ............. 78
* Microsoft y Windows XP son marcas registradas de Microsoft Corporation.
* Macintosh es una marca registrada de Apple Computer.
* El resto de nombres y marcas que aparecen en este manual son propiedad de sus respectivos dueos.
* Los nombres de los fabricantes o de los productos que aparecen en esta tabla son marcas comerciales
o marcas registradas de sus respectivos propietarios. Los nombres se utilizan solo con el fin de ilustrar
caractersticas del sonido y no indican que exista ningn tipo de relacin de las mismas con ZOOM
CORPORATION.
ZOOM G9.2tt 3
speG9.book Page 4 Thursday, March 16, 2006 9:52 PM
Caractersticas
Enhorabuena por la compra de su ZOOM G9.2tt (al que haremos referencia en adelante como "G9.2tt").
El G9.2tt es un sofisticado procesador multiefectos con las siguientes caractersticas y funciones.
4 ZOOM G9.2tt
speG9.book Page 5 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 5
speG9.book Page 6 Thursday, March 16, 2006 9:52 PM
Controles y funciones
Panel superior
Panel trasero
Interruptor OUTPUT GAIN Conector MIDI OUT
(-10 dBm/+4 dBm)
Conector MIDI IN
Puerto USB
6 ZOOM G9.2tt
speG9.book Page 7 Thursday, March 16, 2006 9:52 PM
Controles y funciones
Seccin de control
Indicador Pantalla
[GROUP/BANK]
Seccin de preamplificacin
Mando [BASS] Mando[MIDDLE]
Mando [LEVEL] Mando [TREBLE]
Teclas [CHANNEL A/B] Mando [PRESENCE]
Mando [GAIN]
ZOOM G9.2tt 7
speG9.book Page 8 Thursday, March 16, 2006 9:52 PM
Conexiones
Para realizar las conexiones, consulte los ejemplos que aparecen a continuacin.
Adaptador CA
Ordenador
Guitarra
Para conectar la guitarra, La informacin de
utilice un cable mono cambio de programa y
Interface MIDI sobre el funcionamiento
con blindaje.
Para utilizar el G9.2tt del pedal puede ser
enviada y recibida
Auriculares como interface audio, como mensajes MIDI.
conecte el puerto USB a
un ordenador.
MTR
Ejemplo de conexin (2) (Conexin directa a la entrada de etapa de potencia del amplificador)
Cuando conecte la unidad a la entrada de etapa de potencia del
panel trasero de un amplificador de guitarra, ajuste el
Conmutador OUTPUT GAIN conmutador a "+4 dBm". El G9.2tt dispone de una funcin que
adapta sus caractersticas al amplificador (funcin de seleccin
de amplificador). Para ms informacin, vea la pgina 58.
Guitarra
Amplificador de guitarra (panel trasero)
8 ZOOM G9.2tt
speG9.book Page 9 Thursday, March 16, 2006 9:52 PM
Encendido
Encendido
Para arrancar el G9.2tt debe hacer lo siguiente:
ZOOM G9.2tt 9
speG9.book Page 10 Thursday, March 16, 2006 9:52 PM
@0
Nombre programa Nivel programa
AmpDrive LVL100
Ch.AB BpmTp
Asignacin del pedal de
disparo de funcin 2
Asignacin del pedal de
disparo de funcin 1 Activacin o desactivacin de un
AVISO mdulo con el pie (modo manual)
Puede cambiar de programa dentro
del mismo grupo/banco girando el En el modo manual, puede utilizar los pedales de
mando de parmetro 1.
Para ajustar el nivel del programa (nivel disparo 1 5 para activar o desactivar un mdulo.
de salida del programa individual), gire
el mando de parmetro 2. 1. En el modo de reproduccin, mantenga
pulsado durante ms de un segundo el
2. Para seleccionar un programa pedal de disparo BANK [W].
de otro grupo/banco, utilice El G9.2tt cambiar al modo manual.
los pedales de disparo BANK
[W]/[Q] para elegir el NOTA
grupo/banco y despus use En el modo manual, los pedales de disparo no sirven
para elegir programas. Sin embargo, el mando [TYPE]
los pedales de disparo 1 5. (seleccin de grupo/banco) y el mando de parmetro 1
AVISO Para cambiar de grupo/banco, (seleccin de programa) funcionan igual que en el modo
de reproduccin. Recuerde que debe volver al "modo de
gire el mando [TYPE]. reproduccin" cuando quiera cambiar de programa.
10 ZOOM G9.2tt
speG9.book Page 11 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 11
speG9.book Page 12 Thursday, March 16, 2006 9:52 PM
MOD:Chorus
Depth =100
Valor del parmetro
Nmero/nombre parmetro
NOTA
Si pulsa la tecla del mdulo PRE-
AMP/EQ, la pantalla ser diferente.
Para ms informacin, vea la
pgina 25.
12 ZOOM G9.2tt
speG9.book Page 13 Thursday, March 16, 2006 9:52 PM
NEWDrive :PATCH
@0 STORE?U0-1
Nombre de grupo, n de banco, n programa
destino de grabacin
2. En la parte superior derecha de la pantalla
aparecer la indicacin "PATCH" y en la parte
inferior izquierda "STORE?". Asegrese de que
es esa la operacin que realmente quiere hacer.
Ahora puede grabar programas individuales. Si la pantalla
mostrada es otra diferente, use el mando de parmetro 2 para
hacer que aparezca la indicacin "STORE?" y el mando de
parmetro 3 para hacer que aparezca la indicacin "PATCH".
AVISO En el modo de grabacin, puede intercambiar
programas as como grabar e intercambiar
bancos completos ( p. 28).
3. Utilice los pedales de disparo BANK
[W]/[Q] y 1 5 para seleccionar el banco
y el nmero de programa de destino.
NOTA Solo sern vlidos como destino de grabacin los
programas pertenecientes a un grupo de usuario.
Cuando elija un programa de un grupo de
usuario, este programa se convertir en el
destino de grabacin por defecto.
Cuando elija un programa de un grupo prefijado,
el primer programa de grupo de usuario pasar
a ser el destino de grabacin por defecto.
ZOOM G9.2tt 13
speG9.book Page 14 Thursday, March 16, 2006 9:52 PM
Despus de encender el G9.2tt, la unidad entrar en el modo que le permite elegir y utilizar programas
(modo de reproduccin). Se cargar el programa utilizado por ltima vez. En esta seccin le describimos
los distintos pasos operativos del modo de reproduccin.
A0 AmpDrive LVL100
Ch.AB BpmTp
Si el ajuste mostrado en pantalla
es distinto del ajuste original del
programa, aparecer la
Nmero de banco (0 9) indicacin "E" (de "Editado").
Asignacin del pedal de disparo de funcin 1/2
Le muestra la funcin asignada al pedal de disparo de funcin 1/2 ( p. 38).
Seleccin de un programa
Esta seccin le explica la forma de elegir un
programa en el modo de reproduccin:
1. Pulse un pedal de disparo 1 5 cuyo Se encender el LED del pedal que haya pulsado,
LED no est encendido. para indicarle que ha sido cargado un nuevo
programa.
14 ZOOM G9.2tt
speG9.book Page 15 Thursday, March 16, 2006 9:52 PM
AVISO
En el modo de reproduccin, puede seleccionar
Ajuste del sonido
un parmetro girando el mando de parmetro 1.
Cuando pulse un pedal de disparo cuyo LED En el modo de reproduccin, puede utilizar los
est encendido, se volver a cargar el mismo mandos del panel para ajustar los parmetros
programa. bsicos de la seccin de preamplificador (tipo de
distorsin e intensidad, realce/corte de EQ, etc.).
2. Para cambiar a un programa de otro
banco, utilice los pedales de disparo 1. En el modo de reproduccin, elija el
BANK [W]/[Q] para cambiar de programa.
banco y despus use los pedales de
disparo 1 5 para elegir el programa. 2. Pulse una de las teclas [CHANNEL A/
B] para elegir el canal de previo A B
para su ajuste.
ZOOM G9.2tt 15
speG9.book Page 16 Thursday, March 16, 2006 9:52 PM
Nombre del parmetro que est siendo ajustado Uso del Accelerator
Presence La etapa de entrada del G9.2tt incluye una
-12dB funcin Accelerator que amplifica la seal
Valor parmetro
analgica antes del procesado de efectos por
Representacin grfica del ajuste
de realce/corte en cada banda medio de una circuitera de estado slido. Esto le
permite aadir la caracterstica distorsin y
compresin a vlvulas al sonido limpio producido por
AVISO la circuitera de estado slido y despus enviar la
Cuando ejecute el paso 3 o el 4, el G9.2tt cambiar al seal a la circuitera de efectos.
modo de edicin. Para volver al modo de
reproduccin, pulse la tecla [EXIT]. (Para ms
informacin sobre el modo de edicin, vea la pgina AVISO
24.) El Accelerator est activo en todos los modos. Los
ajustes del Accelerator no son grabados como
5. Para ajustar el nivel global del parte del programa.
programa, gire el mando de parmetro
2 en el modo de reproduccin. Para ajustar el Accelerator, utilice los controles de
la seccin Accelerator del panel. Las funciones de
estos controles son las siguientes:
Mando [PRESENCE]
Realce/corte rango
super-agudos
16 ZOOM G9.2tt
speG9.book Page 17 Thursday, March 16, 2006 9:52 PM
de la distorsin.
Tube Pre-amp
Este ajuste enfatiza la compresin a vlvulas.
Si aumenta ms el ajuste del control [TUBE] se Control [TUBE] Control [BOOST]
producir un aumento drstico del volumen y
ZOOM G9.2tt 17
speG9.book Page 18 Thursday, March 16, 2006 9:52 PM
Control [TUBE]
Este control aade al sonido una caracterstica
distorsin a vlvulas, haciendo que la guitarra
destaque an ms. Cuando gire este mando
totalmente a la izquierda, el efecto estar
desactivado. Conforme vaya girando despus el
mando hacia la derecha, la ganancia de la
circuitera a vlvulas ir aumentando
gradualmente, lo que dar un sonido ms clido
y distorsionado.
Lo normal es que ajuste este control a una
posicin en la que no se oiga demasiado la
distorsin, pero tambin puede ajustarlo a un
valor ms alto cuando quiera enfatizar la
distorsin producida por la circuitera a
vlvulas.
Control [BOOST]
Este control realza bandas de frecuencia para
hacer que el sonido resulte ms pronunciado.
Cuando gire este mando totalmente a la
izquierda, el efecto estar desactivado. Si
despus va girando el mando hacia la derecha,
realzar gradualmente las frecuencias graves y
el rea en torno a 2 kHz. Especialmente cuando
est utilizando un pequeo amplificador de
guitarra o un sistema de audio con respuesta
plana, este control puede serle til para
producir un sonido ms dinmico.
El control [BOOST] le resultar de utilidad en
estas situaciones y para hacer que el sonido de
la guitarra sobresalga ms del fondo cuando
toque en un grupo.
NOTA
La intensidad de la distorsin conseguida con el
control [TUBE] depende de la guitarra y del tipo
de pastilla.
Cuando ambos controles estn al mximo, el
volumen estar muy alto y se producir una
distorsin excesiva.
18 ZOOM G9.2tt
speG9.book Page 19 Thursday, March 16, 2006 9:52 PM
Nivel programa
Le muestra el nivel de
Teclas [CHANNEL A/B]
Le indica el nmero del mando salida del programa Estar encendida la tecla del canal (A B) seleccionado
de parmetro que controla el seleccionado entonces.
entonces para la seccin de preamplificacin.
nivel del programa.
AmpDrive LVL100
Ch.AB BpmTp
Asignacin del pedal de Smbolo "E"
disparo de funcin 1/2 Si el valor ajustado
Le indica la funcin asignada es distinto del que
Teclas de mdulo de efectos
al pedal de disparo de tena el programa
Estarn encendidas en rojo las teclas
funcin 1/2 ( p. 38). original, aparecer la
de los mdulos que estn activos en el
indicacin "E" (de
programa activo en ese momento.
"Editado").
ZOOM G9.2tt 19
speG9.book Page 20 Thursday, March 16, 2006 9:52 PM
NOTA
Los cambios que haya realizado en el programa se
perdern en cuanto elija otro programa. Para
conservarlos, grabe primero el programa ( p.28).
AVISO
Cuando active/desactive un determinado
mdulo, se encender la tecla [STORE/SWAP].
En el modo manual, puede utilizar los mandos
del panel como en el modo de reproduccin
para ajustar los parmetros de pre-
amplificacin, el nivel del programa, el
Accelerator y el Energizer. Para ms informacin
sobre estos procedimientos, vea "Ajuste del
sonido" en la seccin del modo de reproduccin
( p. 15).
Puede cambiar desde el modo manual al de
edicin para editar programas. Para ms
informacin sobre este modo, vea la pgina 24.
20 ZOOM G9.2tt
speG9.book Page 21 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 21
speG9.book Page 22 Thursday, March 16, 2006 9:52 PM
E Nota
Indicador Indicador
Nota [GROUP/BANK] Nota [GROUP/BANK] Despus de encender el G9.2tt, el tono de
AbB D referencia es siempre 440 Hz (La central = 440
A EB Hz). El rango de ajuste utilizando el mando de
BB E parmetro 3 es La central = 435 445 Hz, a
B F intervalos de 1-Hz.
C GB
DB G CHROMATC 442Hz
><
Los smbolos > < en la parte inferior de la pantalla
le indican el grado de desafinacin del tono con
respecto a la nota que aparece en pantalla. AVISO
Cuando apague el G9.2tt y lo vuelva a encender de
nuevo, el tono de referencia ser reiniciado a 440 Hz.
CHROMATC 440Hz
>< 5. Cuando haya terminado con la
El tono afinacin, pulse uno de los pedales
> est bajo de disparo BANK [W]/[Q].
>
>
>
El tono es
>< el correcto
< El G9.2tt volver al modo previo. Si el G9.2tt
estaba en el modo de edicin, cambiar al modo
< de reproduccin.
<
El tono
< est alto AVISO
Para cancelar el estado de bypass/anulacin,
pulse la tecla [BYPASS/TUNER], [EXIT] o uno de
3. Afine la cuerda de su instrumento los pedales de disparo 1 5.
mientras observa las indicaciones de
nota y tono.
22 ZOOM G9.2tt
speG9.book Page 23 Thursday, March 16, 2006 9:52 PM
DB OPEN A
><
440Hz
Str2
6. Afine otras cuerdas de la misma manera.
Nota correcta para la cuerda elegida N de cuerda 7. Cuando haya terminado con la
afinacin, pulse uno de los pedales
de disparo BANK [W]/[Q].
3. Si es necesario, gire el mando de
parmetro 3 para modificar el tono de El G9.2tt volver al modo previo. Si el G9.2tt
referencia del afinador. estaba en el modo de edicin, cambiar al modo
de reproduccin.
El rango para este ajuste es La central = 435 445
Hz, a intervalos de 1-Hz.
AVISO
Cuando haya elegido otro afinador distinto del Cuando apague el G9.2tt y vuelva a encenderlo, el
cromtico, al girar el mando de parmetro 3 hacia tipo de afinador ser reiniciado a su ajuste por
la izquierda ms all del ajuste "435" elegir el defecto (afinador cromtico).
ajuste "b" (un semitono por debajo), "bb" (dos por
debajo) y "bbb" (tres semitonos por debajo).
ZOOM G9.2tt 23
speG9.book Page 24 Thursday, March 16, 2006 9:52 PM
[Configuracin de programa]
ENVIO RETORNO Seccin de preamplificacin
Canal B
ZNR PRE-AMP EQ
ENTRADA COMP WAH/EFX1 EXT LOOP ZNR PRE-AMP EQ CABINET MOD/EFX2 DELAY REVERB SALIDA
Canal A
24 ZOOM G9.2tt
speG9.book Page 25 Thursday, March 16, 2006 9:52 PM
Tecla [WAH/EFX1] Tecla [ZNR] Tecla [EQ] Tecla [MOD/EFX2] Tecla [REVERB]
Tecla [COMP] Tecla [EXT LOOP] Tecla [PRE-AMP] Tecla [CABINET] Tecla [DELAY] Tecla [TOTAL/FUNCTION]
encendidas). Cuando pulse una tecla para elemento recupere su valor original. Sin embargo,
seleccionar un mdulo, el color de la tecla cambiar si haba modificado algn otro elemento ms, la
a naranja (o a verde si el mdulo est desactivado). tecla [STORE/SWAP] permanecer encendida.
[Mdulo PRE-AMP]
NOTA
Puede ajustar a on u off los mdulos PRE-AMP, ZNR
PRE-AMP y EQ independientemente para cada canal (A/B).
FD Clean
Nombre tipo efecto Representacin grfica 4. Para editar el mdulo seleccionado,
simplificada de los haga lo siguiente:
ajustes de EQ
[Mdulo EQ] Cuando haya seleccionado otro mdulo
distinto de PRE-AMP/EQ
Equalizer Para cambiar de tipo de efecto, utilice el mando
Off [TYPE] (para los mdulos que tengan varios tipos
de efectos); use los mandos de parmetros 1 4
para ajustar los parmetros del tipo de efecto. Los
NOTA parmetros asignados a los mandos de parmetros
Si ha activado el modo de edicin desde el 1 4 sern diferentes dependiendo del mdulo y
modo de reproduccin, podr utilizar los del tipo de efecto ( p. 60 75).
pedales de disparo 1 5 para cambiar de
programa. Pero tenga en cuenta que los
cambios realizados se perdern en cuanto
cambie de programa durante la edicin.
Si ha activado el modo de edicin desde el
modo manual, podr utilizar los pedales de
disparo 1 5 para activar o desactivar un Mando [TYPE] Mandos de parmetro 1 - 4
determinado mdulo.
Cuando gire un mando de parmetro, aparecer
3. Para activar o desactivar el mdulo la siguiente pantalla:
seleccionado, pulse de nuevo la
misma tecla de mdulo.
Cuando el mdulo est desactivado, en pantalla MOD:Chorus
aparecer la indicacin "Module Off". Si pulsa Depth = 80
otra vez la misma tecla, activar el mdulo.
N del mando de Valor del parmetro
parmetro usado y
AVISO nombre del parmetro
Si ha modificado el estado de activacin/
desactivacin de algn mdulo, la seleccin del
tipo de efecto o el ajuste de algn parmetro, se AVISO
encender la tecla [STORE/SWAP] y al lado del En aquellos mdulos de efectos con un nico tipo
elemento aparecer la indicacin "E". de efecto (mdulo EQ, CABINET, etc.), no podr
La indicacin "E" desaparecer cuando el cambiar de tipo de efecto.
ZOOM G9.2tt 25
speG9.book Page 26 Thursday, March 16, 2006 9:52 PM
Cuando est seleccionado el mdulo PRE-AMP/EQ mientras que cuando est ajustando un
Siempre podr ajustar los parmetros de los parmetro EQ, lo ser el mdulo EQ.
mdulos PRE-AMP y EQ con los mandos y Los mdulos PRE-AMP, ZNR y EQ le permiten
teclas de la seccin de preamplificador, realizar ajustes de parmetros independientes
independientemente del mdulo activo en ese en los dos canales (A/B). Elija primero el canal y
momento. Las funciones de los mandos y teclas despus ajuste el parmetro.
aparecen indicados en la figura 1.
5. Repita los pasos 2 4 para editar
Cuando la tecla de mdulo de efectos [PRE- otros mdulos de la misma forma.
AMP]/[EQ] est seleccionada, podr utilizar los
mandos de parmetros 1 4 para ajustar otros 6. Cuando haya terminado con el proceso
parmetros del mdulo PRE-AMP/EQ. Las de edicin, pulse la tecla [EXIT].
funciones de los mandos vienen indicadas en la
figura 2.
AVISO
Si est ajustando el parmetro PRE-AMP de la
seccin de pre-amplificacin, el mdulo PRE- El G9.2tt volver al modo previo.
AMP ser seleccionado automticamente,
Figura 1
[Edicin del mdulo PRE-AMP/EQ con la seccin de previo]
Teclas [PRE-AMP A/B]
Selecciona uno de los dos canales de la seccin de previo.
Figura 2
[Edicin del mdulo PRE-AMP/EQ con los mandos de parmetros 1 4 ]
26 ZOOM G9.2tt
speG9.book Page 27 Thursday, March 16, 2006 9:52 PM
NOTA
3. Gire el mando de parmetro 4 para
desplazar la posicin de introduccin
Los cambios que haya realizado en un
programa se perdern en cuanto elija otro. Para de caracteres y utilice los mandos 1
conservarlos, grabe primero el programa ( p. 3 para elegir el nuevo carcter.
28). Los mandos de parmetros 1 3 le permiten
No podr modificar el nivel del programa (nivel elegir los siguientes caracteres.
de salida del programa individual) en el modo de
edicin. Utilice el modo de reproduccin o
Mando de parmetro 1 (nmeros): 0 9
manual para ajustar el nivel.
Mando de parmetro 2 (letras): A Z, a z
Mando de parmetro 3 (smbolos): (espacio)
AVISO $
Si ha entrado en el modo de edicin desde el
modo de reproduccin, podr volver al modo de 4. Repita el paso 3 hasta que haya
reproduccin pulsando los pedales de disparo terminado de introducir el nombre
BANK [W]/[Q] o 1 5. En este caso, cambiar a la que quiera. Pulse despus la tecla
vez el banco/programa.
[EXIT].
Cambio de nombre de un
programa
Puede modificar el nombre de un programa
editado. Para ello, haga lo siguiente:
:0 :A :@ :
NAME:[ewDrive]
El recuadro negro que aparece alternativamente ( )
le indica que puede modificar este carcter.
ZOOM G9.2tt 27
speG9.book Page 28 Thursday, March 16, 2006 9:52 PM
NOTA
Si aparece la indicacin "BANK", la operacin
posterior se realizar para todo el banco.
The G9.2tt entrar en el modo de espera de Asegrese de que aparezca la indicacin correcta.
grabacin y el programa seleccionado entonces se
convertir en la fuente de la operacin de 3. Gire el mando de parmetro 2 para
grabacin/intercambio. que aparezca en pantalla la
El indicador [GROUP/BANK] le mostrar el indicacin "STORE?" o "SWAP?".
nombre del grupo y el nmero del banco destino
de la operacin de grabacin/intercambio.
NEWDrive :PATCH
Le indica que el programa ha sido editado. STORE?U0-1
Nombre del programa fuente de grabacin/intercambio
@0 NEWDrive :PATCH
STORE?U0-1
Cuando est seleccionado "STORE?", el
programa activo podr ser grabado como un
Nombre grupo, n banco, programa de usuario.
Nombre grupo/n banco
destino de grabacin/ n programa destino de Cuando aparezca "SWAP?", el programa de
intercambio. grabacin/intercambio usuario activo podr ser intercambiado con otro
programa de usuario.
AVISO NOTA
Cuando la unidad viene de fbrica, los grupos
Si el programa fuente pertenece a un grupo
de usuario (U, u) contienen los mismos
prefijado, no aparecer la indicacin "SWAP?".
programas que los grupos prefijados (A, b).
Si ha editado un programa, este ser grabado o
intercambiado tal como lo haya editado.
4. Use el mando [TYPE] o los pedales de
disparo BANK [W]/[Q] para elegir el
Si ha elegido un programa de un grupo
prefijado, cuando pulse la tecla [STORE/SWAP], nombre del grupo/nmero de banco
se elegir como destino de grabacin el primer de destino de la operacin de
programa de grupo de usuario. grabacin/intercambio.
28 ZOOM G9.2tt
speG9.book Page 29 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 29
speG9.book Page 30 Thursday, March 16, 2006 9:52 PM
All Initialize?
Y:STORE N:EXIT
2. Pulse de nuevo la tecla [STORE/
SWAP].
Todos los programas recuperarn sus ajustes de
fbrica y el G9.2tt cambiar al modo de
reproduccin. Si pulsa la tecla [EXIT] antes de
ejecutar el paso 2, anular el proceso.
30 ZOOM G9.2tt
speG9.book Page 31 Thursday, March 16, 2006 9:52 PM
P1-2
Mdulo MOD/EFX2
Rate AVISO
Puede ajustar el rango del parmetro cubierto
P1-3 por los pedales de expresin 1 y 2 para cada
Mdulo DELAY destino de control independientemente.
Feed Back En el modo bypass, ambos pedales de
expresin funcionan como pedales de volumen
P1-4 cuando los mueva en direccin vertical. (El
Mdulo REVERB mover el pedal de expresin 2 en direccin
Mix horizontal 2 no tendr efecto).
En el modo de anulacin, ambos pedales de
expresin no tienen efecto.
El pedal de expresin 2 situado en la parte
derecha o pedal Z es sensible no solo al
movimiento vertical sino tambin al horizontal. NOTA
El pedal de expresin 2 del G9.2tt ha sido diseado
Tiene cuatro destinos de control en direccin
para su manejo con los pies. Una vez que haya
vertical (P2V1 a P2V4) y cuatro en direccin girado el pedal totalmente hacia la derecha, si lo
horizontal (P2H1 a P2H4). A cada destino de fuerza hacia abajo, lo golpea, o ejerce sobre l una
control puede asignarle un parmetro. presin excesiva, podra daarlo. Asegrese de
utilizar el pedal solo en el rango para el que ha sido
Con un ajuste como el que aparece en el ejemplo de diseado.
la derecha, cuando mueva el pedal en direccin
ZOOM G9.2tt 31
speG9.book Page 32 Thursday, March 16, 2006 9:52 PM
Asignacin de destinos de
control al pedal de expresin 1
Esta seccin le describe cmo asignar un destino
de control al pedal de expresin 1. Conforme vaya girando el mando de parmetro 1,
ir cambiando el parmetro y el mdulo de efectos.
1. En el modo de reproduccin, elija el
programa.
AVISO
Para ms informacin sobre los parmetros que
AVISO puede elegir como destino de control, vea
Puede ajustar individualmente para cada programa Tipos de efectos y parmetros en las pginas
60 - 75.
los parmetros a ser controlados por los pedales
de expresin 1/2 y el rango de ajuste. Cuando elija Volume como destino de control,
el pedal de expresin 1 funcionar como un
pedal de volumen.
2. Pulse la tecla [PEDAL 1 SETTING]. Si aparece la indicacin NOT Assign, no habr
Aparecer la siguiente pantalla: ningn parmetro asignado al destino de control
activo. Asignando los cuatro destinos de control
Indicacin de destino de control Nombre del parmetro a NOT Assign, desactivar el pedal de
(P1-1 - P1-4) destino de control expresin 1.
P1-1=Resonance NOTA
WAH:AutoWah Si elige NOT Assign, no podr ejecutar los pasos
Nombre de mdulo Nombre del tipo de efecto 5 y 6.
PDL1 :Target1
min= 50
Valor mnimo
Los pasos posteriores son los mismos para P1-1 a Cuando utilice el mando de parmetro 3
P1-4 .
PDL1 :Target1
4. Gire el mando de parmetro 1 para MAX=100
elegir el parmetro a controlar. Valor mximo
32 ZOOM G9.2tt
speG9.book Page 33 Thursday, March 16, 2006 9:52 PM
AVISO
9. Si es necesario, grabe el programa.
El rango disponible para el ajuste depender del
parmetro elegido en el paso 4.
NOTA
Tambin es posible ajustar min a un valor Los cambios que haya realizado en los ajustes del
superior que MAX. En este caso, el parmetro pedal se perdern en cuanto elija un nuevo
estar al mnimo cuando pulse a tope el pedal,
programa. Para conservarlos, grabe el programa
mientras que estar al mximo cuando levante
( p. 28).
el pie del pedal.
ZOOM G9.2tt 33
speG9.book Page 34 Thursday, March 16, 2006 9:52 PM
PDL2-V:Target1
min= 50
Los pasos posteriores son los mismos para P2V1 Valor mnimo
a P2V4. Cuando utilice el mando de parmetro 3
AVISO
El rango disponible para el ajuste depender del
parmetro elegido en el paso 4.
Conforme vaya girando el mando de parmetro 1, Tambin es posible ajustar min a un valor
ir cambiando el parmetro y el mdulo de efectos . superior que MAX. En este caso, el parmetro
estar al mnimo cuando pulse a tope el pedal, y
al mnimo cuando levante el pie del pedal.
AVISO
Para ms informacin sobre los parmetros que
puede elegir como destino de control, vea Tipos 6. Para utilizar el pedal de expresin 2
de efectos y parmetros en las pginas 60 75. para activar o desactivar el mdulo,
Cuando elija Volume como destino de control, gire el mando de parmetro 4 y elija
el pedal de expresin 2 funcionar como un Enable.
pedal de volumen. El pedal de expresin 2 tiene un interruptor que se
Si aparece la indicacin NOT Assign, no habr dispara cuando pise en direccin vertical el pedal
ningn parmetro asignado al destino de control un poco ms all del tope. Se activar o
activo. Asignando los cuatro destinos de control
a NOT Assign, desactivar el pedal de
desactivar el mdulo al cual pertenece el
expresin 2. parmetro seleccionado.
34 ZOOM G9.2tt
speG9.book Page 35 Thursday, March 16, 2006 9:52 PM
NOTA
Tambin es posible elegir el mismo parmetro para
ms de un destino de control, si bien en algunos
casos, los cambios extremos en el valor del PDL Calibration
parmetro producen ruido. Esto no es ningn defecto . PEDAL1...min
11. Cuando haya realizado todos los 2. Con el pedal de expresin 1 en la
ajustes para el pedal de expresin 2, posicin de puntera arriba, pulse
pulse la tecla [EXIT]. [STORE/SWAP].
Pedal arriba
del todo
La unidad volver al modo de reproduccin.
ZOOM G9.2tt 35
speG9.book Page 36 Thursday, March 16, 2006 9:52 PM
PDL Calibration
Pulse hasta el fondo,
de modo que el
PEDAL2-V...min
pedal toque aqu
2. Con el pedal de expresin 2 en la
posicin de puntera arriba, pulse
[STORE/SWAP].
PDL Calibration
Ya habr terminado con el ajuste del pedal de PEDAL2-V...MAX
expresin y la unidad volver al modo de
reproduccin. 3. Pulse a tope el pedal de expresin 2
en direccin vertical y despus
levante el pie del pedal y pulse la
AVISO
tecla [STORE/SWAP].
El punto en el que el mdulo es activado o
desactivado al pulsar el pedal de expresin 1 es
siempre el mismo, independientemente de la
accin realizada en el paso 3.
Pulse hasta el fondo,
Para ms informacin sobre la funcin de de modo que el
activacin/desactivacin del mdulo, vea la pedal toque aqu
pgina 33.
Si aparece en pantalla la indicacin ERROR,
repita el procedimiento desde el paso 2.
36 ZOOM G9.2tt
speG9.book Page 37 Thursday, March 16, 2006 9:52 PM
PDL Calibration
PEDAL2-H...min
4. Saque el tope del pedal de expresin
2 para fijar el pedal. Desplace
despus el pedal de expresin
totalmente hacia la derecha y pulse la
tecla [STORE/SWAP].
Pedal de expresin 2
PDL Calibration
PEDAL2-H...MAX
5. Pulse el tope del pedal de expresin 2,
desplace despus el pedal de
expresin totalmente hacia la derecha
y pulse la tecla [STORE/SWAP].
AVISO
Si aparece en pantalla la indicacin ERROR,
repita el procedimiento desde el paso 2.
ZOOM G9.2tt 37
speG9.book Page 38 Thursday, March 16, 2006 9:52 PM
AVISO
BPM TAP
Puede realizar la asignacin del pedal de disparo de
funcin 1/2 independientemente para cada programa. El pedal de disparo de funcin se utiliza para
especificar el tempo individual para un programa
2. Pulse la tecla de mdulo de efectos ( p. 39). Cuando pulse el pedal repetidamente,
[TOTAL/FUNCTION]. el tempo ser ajustado al intervalo transcurrido
entre las dos ltimas pulsaciones.
La asignacin del pedal de disparo de funcin
forma parte del mdulo [TOTAL/FUNCTION].
Aparecer la siguiente pantalla: AVISO
Utilizando el tempo ajustado aqu, podr
sincronizar determinados parmetros (Time y Rate)
TOTAL:Tempo en unidades de notas ( p. 40).
BPM =120
Delay TAP
3. Gire los mandos de parmetro 2/3 El pedal de disparo de funcin sirve para especificar
para elegir la funcin que quiera el parmetro Time para el mdulo DELAY.
asignar a los pedales de disparo de
funcin 1/2.
AVISO
Utilice el mando de parmetro 2 para el pedal de Mientras que BPM TAP especifica el tempo para
disparo de funcin 1 y el mando de parmetro 3 un programa individual, Delay TAP usa el
para el pedal de disparo de funcin 2. intervalo de las pulsaciones del pedal para
Aparecer la siguiente pantalla: ajustar directamente el valor del parmetro Time
(tiempo de retardo).
Cuando gire el mando de parmetro 2 Para poder usar Delay TAP, el mdulo DELAY
debe estar activado para ese parmetro.
TOTAL:Function1
PRE-AMP CH A/B Hold Delay
Funcin asignada al pedal de El pedal de disparo de funcin controla la
disparo de funcin 1 activacin/desactivacin de la funcin de
mantenimiento de retardo. Cuando escoja un
Cuando gire el mando de parmetro 3
programa que utilice la funcin de
TOTAL:Function2 mantenimiento, al pulsar el pedal de disparo de
BPM TAP funcin activar el mantenimiento, haciendo
que se repita el sonido retardado activo. Si
Funcin asignada al pedal de pulsa el pedal de disparo de funcin de nuevo
disparo de funcin 2
desactivar el mantenimiento y el sonido
retardado pasar a tener una fase de
Puede asignar las siguientes funciones al pedal de decaimiento como ocurre normalmente (vea la
disparo de funcin 1/2. imagen que hay en la pgina siguiente).
38 ZOOM G9.2tt
speG9.book Page 39 Thursday, March 16, 2006 9:52 PM
Sonido
original
Sonido retardado
Mantenimiento
AVISO
Para poder utilizar Hold Delay, el mdulo DELAY
debe estar activado para ese programa.
Delay Mute
NOTA
El pedal de disparo de funcin activa o Los cambios que haya realizado en las
desactiva la anulacin de la seal de entrada del asignaciones del pedal se perdern en cuanto elija
mdulo DELAY. un nuevo programa. Para conservarlos, grabe el
programa ( p. 28).
Bypass OnOff, Mute OnOff
El pedal de disparo de funcin controla la
Cuando cargue el programa grabado, el pedal de
activacin/desactivacin de la funcin bypass o
disparo de funcin controlar la funcin
mute. Cuando est activado alguno de estos seleccionada.
modos, aparecer la pantalla del afinador.
Manual Mode
El pedal de disparo de funcin servir para Ajuste del tempo de un
cambiar entre el modo de reproduccin y el programa
modo manual.
COMP OnOff, WAH/EFX1 OnOff, EXT El G9.2tt le permite especificar el tempo para cada
LOOP OnOff, ZNR OnOff, PRE-AMP programa a nivel individual y sincronizar
OnOff, EQ OnOff, MOD/EFX2 OnOff, determinados parmetros a este tempo en unidades
DELAY OnOff, REVERB OnOff de notas. Este apartado le explica cmo especificar y
El pedal de disparo de funcin se utilizar para utilizar el ajuste del tempo para un programa:
activar/desactivar el correspondiente mdulo.
1. En el modo de reproduccin, elija el
programa.
HINT
Cuando elija PRE-AMP CH A/B, el piloto del
correspondiente pedal de disparo de funcin se
2. Pulse la tecla de mdulo de efectos
encender en rojo (A) o en verde (B). Cuando
[TOTAL/FUNCTION].
seleccione BPM TAP o Delay TAP, el LED El ajuste de tempo para cada programa forma
parpadear en naranja de forma sincronizada parte del mdulo [TOTAL/FUNCTION].
con el ajuste BPM. Cuando pulse la tecla del mdulo de efectos
Tambis es posible asignar la misma funcin a [TOTAL/FUNCTION], aparecer en pantalla el
ambos pedales de disparo. ajuste de tempo activo.
ZOOM G9.2tt 39
speG9.book Page 40 Thursday, March 16, 2006 9:52 PM
x2 Negra x 2
4. Para sincronizar un parmetro
: :
respecto al tempo especificado, elija
el tipo de efecto y el parmetro de x20 Negra x 20
efectos a sincronizar y seleccione el
smbolo de la nota a cuyo valor quiera NOTA
sincronizar el parmetro. El rango de ajuste disponible depender del
El valor ajustado para parmetros de efectos que parmetro.
admitan sincronizacin respecto al tempo puede ser
seleccionado en unidades de notas, utilizando como Cuando haya seleccionado el ajuste de corchea, el
referencia el tempo especfico del programa. parmetro Time ser ajustado a un valor que
corresponde a una corchea en el tempo especfico
Por ejemplo, el parmetro Time del tipo de efecto del programa. Cuando modifique el tempo,
TAPE ECHO en el mdulo MOD/EFX2 admite la tambin cambiar el tiempo de retardo de acuerdo
sincronizacin con el tempo de un programa a l.
concreto. Para utilizar esta opcin, gire el mando
de parmetro correspondiente desde el ajuste
NOTA
mximo (2000) hacia la derecha hasta que Dependiendo de la combinacin del ajuste de
aparezca en pantalla un smbolo de nota. tempo y del smbolo de nota elegido, el rango
mximo de valores del parmetro (como 2000 ms)
puede ser sobrepasado. En este caso, el valor ser
AVISO automticamente dividido por la mitad (o ajustado
En la seccin Tipos de efectos y parmetros (
a 1/4 si el rango ha sido sobrepasado
pginas 60 75), los parmetros que admiten
excesivamente.
sincronizacin respecto al tempo vienen indicados
mediante un smbolo de nota.
6. Cuando haya terminado con el ajuste
del tempo y de los parmetros, pulse
5. Escoja un valor para el parmetro
la tecla [EXIT].
eligiendo un smbolo de nota.
La unidad volver al modo de reproduccin.
Puede escoger entre los siguientes ajustes:
Grabe el programa si quiere.
3 Tresillo de blancas
40 ZOOM G9.2tt
speG9.book Page 41 Thursday, March 16, 2006 9:52 PM
EXT LOOP
Efecto externo SendLevel= 50
NOTA
Cuando aparezca la indicacin "EXT LOOP
Module OFF", el mdulo EXT LOOP estar
entonces desactivado. Pulse la tecla [EXT LOOP]
para activarlo.
ZOOM G9.2tt 41
speG9.book Page 42 Thursday, March 16, 2006 9:52 PM
EXT LOOP
Dry Level= 80
AVISO
Si el efecto externo es de alguno de los tipos
que mezcla el sonido con efectos con el sonido
original (como una reverb, chorus o retardo),
ajuste el balance de nivel entre el sonido original
y el sonido con efectos ajustando el nivel de
retorno y el nivel de la seal seca.
Si el efecto externo es de alguno de los tipos
que procesa la seal de entrada para su salida
(como un compresor o un ecualizador), el nivel
de seal seca debe ser ajustado normalmente a
0 y el nivel de seal debe regulado con el
parmetro de nivel de retorno.
AVISO
Si la unidad de efectos externa admite los cambios
de programa va MIDI, el G9.2tt podr controlar los
efectos enviando mensajes de cambio de
programa. De esta forma, puede sincronizar el
cambio de programa y el cambio de lista de
programas en el G9.2tt ( p. 44).
42 ZOOM G9.2tt
speG9.book Page 43 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 43
speG9.book Page 44 Thursday, March 16, 2006 9:52 PM
Envo y recepcin de
MIDI 5/28 informacin de cambio de
Tx Ch=1 programa va MIDI (cambio
5. Gire el mando de parmetro 1 para
de programa)
elegir el canal MIDI (1 16) en el que
Puede enviar y recibir informacin de cambio de
el G9.2tt enviar mensajes MIDI. programa en el G9.2tt va MIDI a travs de
mensajes de cambio de programa o seleccin de
6. Cuando haya terminado el ajuste, banco + cambio de programa.
pulse la tecla [EXIT] para salir del Hay dos formas de hacer esto (modos de cambio
men AMP SELECT/SYSTEM. de programa):
En pantalla aparecer el mensaje Store...?, que
le preguntar si quiere grabar las modificaciones Modo directo
realizadas. Con este mtodo, se utiliza una combinacin de
mensajes de seleccin de banco MIDI y de
cambio de programa para indicar el programa.
Store... ? En el ajuste por defecto, todos los programas
Y[STORE] N[EXIT] del G9.2tt estn asignados a un nmero de
banco MIDI y un nmero de cambio de
programa MIDI. Puede utilizar estos para
7. Pulse [STORE/SWAP] para grabar los
especificar directamente un programa.
cambios.
AVISO
Los mensajes MIDI de seleccin de banco son
un tipo de mensajes para especificar la
categora de sonido de un sintetizador o
dispositivo similar. Se usan en combinacin de
El ajuste del canal MIDI ser aceptado y la unidad mensajes de cambio de programa.
volver al modo de reproduccin. Normalmente, la seleccin de banco se especifica
En la situacin anterior, solo estarn activas las en dos partes, utilizando el valor MSB (bit ms
teclas [STORE/SWAP] y [EXIT]. Para anular los significativo) y LSB (bit menos significativo).
cambios y volver al modo de reproduccin sin
grabar nada, pulse la tecla [EXIT].
Modo de distribucin o mapeo
En este mtodo, solo se utilizan mensajes de
cambio de programa MIDI para especificar el
programa. Para asignar los nmeros de cambio
de programa 0 127 a los programas se utiliza
un mapa de cambio de programa, para que la
seleccin se realice usando esta informacin.
Con este mtodo puede especificar un mximo
de 128 programas.
44 ZOOM G9.2tt
speG9.book Page 45 Thursday, March 16, 2006 9:52 PM
Store... ? AVISO
Para ms informacin acerca de qu nmero de
Y[STORE] N[EXIT] cambio de programa/nmero de banco est
asignado a cada programa, vea la lista que
5. Pulse la tecla [STORE/SWAP] para aparece al final de este manual ( p. 79).
grabar los cambios.
El ajuste ser aceptado y la unidad volver al 4. Cuando haya terminado con el ajuste,
modo de reproduccin. pulse [EXIT] para salir del men AMP
En la situacin anterior, solo estarn activas las SELECT/SYSTEM.
teclas [STORE/SWAP] y [EXIT]. Si pulsa Si ha modificado algn ajuste del men AMP
ZOOM G9.2tt 45
speG9.book Page 46 Thursday, March 16, 2006 9:52 PM
46 ZOOM G9.2tt
speG9.book Page 47 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 47
speG9.book Page 48 Thursday, March 16, 2006 9:52 PM
Asignacin de nmeros de
AMP Select 1/28 cambio de control
Puede asignar nmeros de cambio de control al
FRONT pedal de expresin y a las teclas del G9.2tt. Para
ello, haga lo siguiente:
2. Para permitir que el G9.2tt pueda
recibir mensajes de cambio de
control, gire el mando [TYPE] para NOTA
que aparezca el parmetro MIDI Antes de llevar a cabo los siguientes pasos,
CTRL Rx (recepcin de cambio de compruebe que el ajuste del canal MIDI de envo/
control) y gire el mando de parmetro recepcin del G9.2tt sea correcto ( p. 43) y que
1 para seleccionar el ajuste ON. est activado el envo/recepcin de mensajes de
cambio de control ( p. 47).
Store... ?
Y[STORE] N[EXIT] AVISO
La asignacin de nmero de cambio de control
siempre se aplica tanto al envo como a la
5. Pulse la tecla [STORE/SWAP] para recepcin.
grabar los cambios.
El ajuste ser aceptado y la unidad volver al 3. Gire el mando de parmetro 1 para
modo de reproduccin. especificar un nmero de cambio de
En la situacin anterior, solo estarn activas las control.
teclas [STORE/SWAP] y [EXIT]. Si pulsa
[EXIT], anular los cambios y la unidad volver
al modo de reproduccin sin grabar nada.
48 ZOOM G9.2tt
speG9.book Page 49 Thursday, March 16, 2006 9:52 PM
ZOOM G9.2tt 49
speG9.book Page 50 Thursday, March 16, 2006 9:52 PM
50 ZOOM G9.2tt
speG9.book Page 51 Thursday, March 16, 2006 9:52 PM
BulkDumpTx 27/28
ExctePress[PAGE]
ZOOM G9.2tt 51
speG9.book Page 52 Thursday, March 16, 2006 9:52 PM
Otras funciones
ARRM=Mix
MOD:Chorus La diferencia entre un rango de ajuste para un
parmetro comprendido entre 0 (mnimo) 100
Nombre mdulo Nombre tipo de efecto (mximo) y 20 (mnimo) 80 (mximo) queda
perfectamente clara en el grfico que aparece en
3. Gire el mando de parmetro 1 para la pgina siguiente.
seleccionar el parmetro de destino
de control.
52 ZOOM G9.2tt
speG9.book Page 53 Thursday, March 16, 2006 9:52 PM
Otras funciones
Sinusoidal
7
(Sine)
AVISO
El ajuste que podr hacer del rango depende del 8 Cuadrada
parmetro. (Square)
Tambin es posible ajustar min a un valor
superior a MAX. En este caso, se invertir la 7. Gire el mando de parmetro 2 para
direccin del cambio de control. seleccionar el ciclo de la forma de
onda de control.
5. Para elegir el tipo de forma de onda Aparecer la siguiente pantalla:
de control y el ciclo, pulse una vez la
tecla [PAGE] para cambiar de pgina.
TOTAL:ARRM SYNC
Sync=x2
ZOOM G9.2tt 53
speG9.book Page 54 Thursday, March 16, 2006 9:52 PM
Otras funciones
Software
DAW
G9.2tt
[INPUT] USB
Efectos
[USB]
[OUTPUT]
Fig. 2: Flujo de seal durante la reproduccin (1)
Software
[INPUT]
G9.2tt DAW
Efectos
USB
[OUTPUT] [USB]
Fig. 3: Flujo de seal durante la reproduccin (2)
[INPUT]
G9.2tt Software
Efectos DAW
USB
[OUTPUT] [USB]
54 ZOOM G9.2tt
speG9.book Page 55 Thursday, March 16, 2006 9:52 PM
Otras funciones
AVISO
El ajuste del parmetro USB Monitor ser
Anulacin de la salida reinicializado a su valor por defecto (USB+DIRECT)
directa cuando est cuando apague la unidad y vuelva a encenderla de
nuevo.
usando una conexin USB
Cuando el G9.2tt est conectado a un ordenador y
lo utilice como interface audio, si quiere puede
anular la seal que aparece en la toma OUTPUT
despus del procesado de efectos. Para ello, haga
lo siguiente:
ZOOM G9.2tt 55
speG9.book Page 56 Thursday, March 16, 2006 9:52 PM
Otras funciones
LCD 2/28
Contrast:2
56 ZOOM G9.2tt
speG9.book Page 57 Thursday, March 16, 2006 9:52 PM
Enlace de efectos
Los programas del G9.2tt constan de diez mdulos de efectos, como puede ver en la imagen de abajo.
Puede utilizar todos los mdulos de efectos a la vez o puede usar selectivamente determinados mdulos
activndolos o desactivndolos.
Canal B
Seccin de previo
ZNR PRE-AMP EQ
ZNR FD Clean EQ
COMP WAH/EFX1 EXT LOOP ZNR PRE-AMP EQ CABINET MOD/EFX2 DELAY REVERB
Compressor AutoWah Noise
ZNR FDVX Clean
Clean EQ CABINET Chorus Delay Hall
Gate
RackComp A-Resonance Noise VXJC Clean
Clean ST-Chorus PingPongDly Room
Dirty
Gate
Limiter Booster Gate JCHW Clean
Clean Ensemble Echo Spring
Dirty
Tremolo Gate HW Clean ModDelay PingPongEcho Arena
La serie de cinco mdulos EXT LOOP, ZNR, Cuando est activado el mdulo
PRE-AMP, EQ y CABINET funciona como un CABINET
previo virtual con dos canales. Los mdulos ZNR, El algoritmo para grabaciones directas queda
PRE-AMP y EQ pueden tener distintos ajustes seleccionado en el mdulo PRE-AMP. Este
para los canales A y B, lo que le permite cambiar algoritmo optimiza el sonido para la
de canal tambin dentro del mismo programa. reproduccin a travs de un sistema de
respuesta plana. Esta es la opcin recomendada
cuando el G9.2tt est conectado a una
Cambio entre el sonido en grabadora o un sistema hifi.
vivo y el sonido de
grabacin directa
PRE-AMP EQ CABINET
El mdulo PRE-AMP del G9.2tt dispone de 44 Algoritmo para On
grabacin directa
tipos de efectos, pero cada uno de esos tipos de Off
efectos tiene dos algoritmos, uno para actuaciones Algoritmo para
en vivo y otro para grabaciones directas. Esto actuaciones en vivo
supone que tiene acceso a 88 tipos de efectos.
ZOOM G9.2tt 57
speG9.book Page 58 Thursday, March 16, 2006 9:52 PM
Enlace de efectos
58 ZOOM G9.2tt
speG9.book Page 59 Thursday, March 16, 2006 9:52 PM
Enlace de efectos
COMP WAH/EFX1 EXT LOOP ZNR PRE-AMP EQ CABINET MOD/EFX2 DELAY REVERB
COMP EXT LOOP ZNR PRE-AMP EQ CABINET WAH/EFX1 MOD/EFX2 DELAY REVERB
COMP WAH/EFX1 MOD/EFX2 DELAY EXT LOOP ZNR PRE-AMP EQ CABINET REVERB
COMP MOD/EFX2 DELAY EXT LOOP ZNR PRE-AMP EQ CABINET WAH/EFX1 REVERB
ZOOM G9.2tt 59
speG9.book Page 60 Thursday, March 16, 2006 9:52 PM
Parmetros de efectos 1 4
Cuando est seleccionado este tipo de efecto, podr ajustar los
cuatro parmetros que aparecen aqu con los mandos 1 - 4.
Mdulo de efectos Tambin aparecer indicado el rango para cada parmetro.
Algunos parmetros de efectos se ajustan con los mandos de la
Tipo de efectos seccin de previo.
WAH/EFX1 module
This module comprises wah and fi lter effects as well as special effects such as ring
modulator and octave.
AutoWah
This effect varies wah in accor dance with picking intensity .
A-Resonance
This effect varies the resonance filter frequency in accordance with picking intensity .
The above two effect types have the same parameters.
PARM1 PARM2 PARM3 PARM4
Delay
This is a long delay with a maximum setting of 5000 ms.
Sincronizacin de tempo
El smbolo de nota ( ) en la tabla le indica que puede sincronizar el parmetro al tempo
especfico del programa. Si elige el smbolo de nota como valor para el parmetro durante el
ajuste en el G9.2tt, el valor del parmetro ser sincronizado al tempo especfico del programa en
unidades de notas ( p. 39).
Pedal de expresin
Un icono de pedal ( ) en la tabla le indica que el parmetro puede ser controlado por medio
del pedal de expresin 1/2. Si elige el parmetro como destino de control durante el ajuste en el
G9.2tt ( p. 32 35), el pedal de expresin 1/2 controlar el parmetro en tiempo real cuando
seleccione el programa. Tambin puede elegir como destinos de control para la funcin ARRM
los parmetros con un icono de pedal.
60 ZOOM G9.2tt
speG9.book Page 61 Thursday, March 16, 2006 9:52 PM
Mdulo COMP
Atena los agudos y realza los graves, colocando el nivel global de seal dentro de un
determinado rango.
Compressor
Es un compresor de tipo MXR Dynacomp.
PARM1 PARM2 PARM3 PARM4
Sense 0 10 Attack Fast, Slow Tone 0 10 Level 2 100
Ajusta la sensibilidad del
Le permite elegir entre dos Ajusta el nivel de la seal
compresor. Cuanto mayor sea Ajusta la calidad tonal del
velocidades de ataque: rpida despus de pasar por el
el valor introducido mayor sonido.
o lenta. mdulo.
ser la sensibilidad.
RackComp
Este tipo de efecto le permite realizar un ajuste ms detallado que el de "Compressor".
PARM1 PARM2 PARM3 PARM4
Threshold 0 50 Ratio 1 10 Attack 1 10 Level 2 100
Ajusta el nivel de la seal de Ajusta el nivel de la seal
Ajusta la velocidad de ataque
referencia que har que se Ajusta el ratio de compresin. despus de pasar por el
del compresor.
active el compresor. mdulo.
Limiter
Es un limitador que suprime los picos de seal por encima de un determinado nivel de referencia.
PARM1 PARM2 PARM3 PARM4
Threshold 0 50 Ratio 1 10 Release 1 10 Level 2 100
Ajusta el retardo entre el punto
Ajusta el nivel de la seal de Ajusta el nivel de la seal
Ajusta el ratio de compresin en el que el nivel de seal cae
referencia que har que se despus de pasar por el
del limitador. por debajo del nivel umbral y
active el limitador. mdulo.
la salida del limitador.
Mdulo WAH/EFX1
Incluye efectos de wah y de filtro as como efectos especiales como el modulador de
repique y un octavador.
AutoWah
Este efecto produce un sonido wah que depende de la intensidad de pulsacin.
Para conocer los parmetros de efectos, vea A-Resonance (el siguiente efecto).
A-Resonance
Este efecto modifica la banda de frecuencias del filtro de resonancia dependiendo de la intensidad del punteo.
PARM1 PARM2 PARM3 PARM4
Booster
Aumenta la ganancia de seal.
PARM1 PARM2 PARM3 PARM4
Range 15 Tone 0 10 Gain 0 10 Level 2 100
Elige la banda de frecuencias Ajusta la calidad tonal del Ajusta el nivel de la seal
Ajusta la cantidad de realce.
que ser realzada. sonido. despus de pasar por el mdulo.
ZOOM G9.2tt 61
speG9.book Page 62 Thursday, March 16, 2006 9:52 PM
Tremolo
Este efecto modifica peridicamente el volumen.
PARM1 PARM2 PARM3 PARM4
UP 0 9,
Depth 0 100 Rate 0 50 Wave DWN 0 9, Level 2 100
TRI 0 9
Le permite elegir la forma de
onda de modulacin. Los ajustes
disponibles son: "UP" (dientes
de sierra hacia arriba), "DWN" Ajusta el nivel de seal
Ajusta la profundidad de Ajusta la velocidad de
(dientes de sierra hacia abajo) y despus de pasar por el
modulacin. modulacin.
"TRI" (triangular). Cuanto mdulo.
mayor sea el valor, mayor ser la
saturacin de los picos de onda,
lo que reforzar el efecto.
Phaser
Este efecto produce un sonido con un carcter de pulsacin.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Rate 0 50 Color 14 Level 2 100
Elige la posicin de conexin del
mdulo WAH/EFX1. Los ajustes Ajusta el nivel de seal
Ajusta la velocidad de
disponibles son: "Befr" (antes de Ajusta el color del sonido. despus de pasar por el
modulacin.
la seccin de preamplificacin) o mdulo.
"Aftr" (despus del previo).
FixedPhaser
Es un modulador de fase fijo que puede ser utilizado como un ecualizador.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Frequency 1 50 Color 14 Level 2 100
Elige la posicin de conexin del
mdulo WAH/EFX1. Los ajustes Ajusta el nivel de seal
Ajusta la banda de frecuencias
disponibles son: "Befr" (antes de Ajusta el color del sonido. despus de pasar por el
que ser reforzada.
la seccin de preamplificacin) o mdulo.
"Aftr" (despus del previo).
RingModulate
Este efecto produce un sonido metlico de repique. Al ajustar el parmetro "Freq" obtendr un cambio drstico del
carcter del sonido.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Frequency 1 50 Balance 0 100 Level 2 100
Elige la posicin de conexin del
mdulo WAH/EFX1. Los ajustes Ajusta el nivel del sonido con Ajusta el nivel de seal
Ajusta la frecuencia utilizada
disponibles son: "Befr" (antes de efectos que es mezclado con el despus de pasar por el
para la modulacin.
la seccin de preamplificacin) o sonido original. mdulo.
"Aftr" (despus del previo).
SlowAttack
Este efecto reduce la velocidad de ataque, produciendo un sonido de tipo violn.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Time 1 50 Curve 0 10 Level 2 100
Elige la posicin de conexin del
mdulo WAH/EFX1. Los ajustes Ajusta el nivel de seal
Ajusta el tiempo de Ajusta la curva de cambio de
disponibles son: "Befr" (antes de despus de pasar por el
crecimiento. aumento de volumen.
la seccin de preamplificacin) o mdulo.
"Aftr" (despus del previo).
62 ZOOM G9.2tt
speG9.book Page 63 Thursday, March 16, 2006 9:52 PM
PedalVox
Simulacin del clsico pedal wah Vox.
Para consultar sus parmetros de efectos, vea PedalCry (el siguiente efecto).
PedalCry
Simulacin del clsico pedal wah Crybaby.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Frequency 1 50 DryMix 0 10 Level 2 100
Elige la posicin de conexin Ajusta la frecuencia que ser
del mdulo WAH/EFX1. Los enfatizada. Cuando no use
Ajusta el nivel del sonido con Ajusta el nivel de seal
ajustes disponibles son: "Befr" ningn pedal de expresin, el
efectos que es mezclado con el despus de pasar por el
(antes de la seccin de previo) efecto equivale a pulsar el
sonido original. mdulo.
o "Aftr" (despus de la seccin pedal hasta la mitad de su
de preamplificacin). recorrido.
MultiWah
Es un efecto wah que le permite elegir la curva que seguir la frecuencia reforzada.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Frequency 1 50 Curve 1 10 Level 2 100
Elige la posicin de conexin Ajusta la frecuencia que ser
del mdulo WAH/EFX1. Los enfatizada. Cuando no use
Ajusta el nivel de seal
ajustes disponibles son: "Befr" ningn pedal de expresin, el Ajusta la curva que seguir la
despus de pasar por el
(antes de la seccin de previo) efecto equivale a pulsar el frecuencia (PARM2).
mdulo.
o "Aftr" (despus de la seccin pedal hasta la mitad de su
de preamplificacin). recorrido.
P-Resonance
Pedal wah con un carcter potente.
PARM1 PARM2 PARM3 PARM4
Position Befr, Aftr Frequency 1 50 Resonance 0 10 Level 2 100
Elige la posicin de conexin
del mdulo WAH/EFX1. Los
Ajusta el nivel de seal
ajustes disponibles son: "Befr" Ajusta la frecuencia de Ajusta la intensidad de la
despus de pasar por el
(antes de la seccin de previo) modulacin. resonancia.
mdulo.
o "Aftr" (despus de la seccin
de preamplificacin).
Octave
Le aade al sonido original un componente una octava inferior.
PARM1 PARM2 PARM3 PARM4
OctLevel 0 100 DryLevel 0 100 Tone 0 10 Level 2 100
Ajusta el nivel del Ajusta la calidad tonal del Ajusta el nivel de seal
Ajusta el nivel del sonido
componente de sonido una componente de sonido una despus de pasar por el
original.
octava inferior. octava inferior. mdulo.
ZOOM G9.2tt 63
speG9.book Page 64 Thursday, March 16, 2006 9:52 PM
Mdulo ZNR
Este mdulo sirve para reducir el ruido durante las pausas de ejecucin. Le ofrece una
opcin de reduccin de ruido y otra de puerta de ruidos (corta el sonido durante las pausas
de ejecucin).
ZNR (ZOOM NOISE REDUCTION)
La reduccin de ruidos original desarrollada por ZOOM corta el ruido durante las pausas de ejecucin sin afectar al
tono global.
NoiseGate
Es una puerta de ruidos que corta totalmente el sonido durante las pausas de ejecucin.
DirtyGate
Es una puerta de ruidos clsica con caractersticas de corte especiales.
Los tres tipos de efectos anteriores tienen los mismos parmetros.
PARM1
Threshold 1 16
Ajusta la sensibilidad del ZNR. Para la mxima
reduccin de ruido, ajuste el valor tan alto como
sea posible sin que el sonido tenga un decaimiento
totalmente artificial.
64 ZOOM G9.2tt
speG9.book Page 65 Thursday, March 16, 2006 9:52 PM
JC Clean HW Clean
Sonido limpio de la serie JC de Roland con chorus Sonido limpio del legendario Hiwatt Custom 100 de
interno que da lugar a un sonido amplio y limpio. Britain totalmente a vlvulas.
UK Blues US Blues
Sonido crunch del combo de 1962 Bluesbreaker de Sonido crunch de un Fender Tweed Deluxe de 1953.
Marshall.
TweedBass BG Crunch
Sonido crunch del Fender Bassman, un amplificador de Sonido crunch del combo Mesa Boogie MkIII.
bajo con una gran presencia.
VX Crunch Z Combo
Sonido crunch del combo Vox AC30TBX, funcionando Sonido crunch de un combo original de Zoom.
en el modo de clase A.
MS #1959 MS Crunch
Sonido de una torre Marshall JCM800 cuyo rango va
Sonido crunch del legendario Marshall de 1959. desde un sonido limpio hasta uno crunch.
HK Clean HK Crunch
Sonido limpio del famoso modelo Triamp MKII de Sonido crunch del famoso modelo Triamp MKII de
Hughes & Kettner (Amp 1). Hughes & Kettner (Amp 2).
HK Drive DZ Clean
Sonido de alta ganancia del famoso modelo Triamp MKII Sonido limpio del canal 1 del amplificador de guitarra
alemn Diezel Herbert (fabricado a mano), con tres
de Hughes & Kettner (Amp 3). canales controlables por separado.
DZ Crunch DZ Drive
Sonido crunch del canal 2 del amplificador Diezel Herbert. Sonido de alta ganancia del canal 3 del amplificador Diezel Herbert.
Z Stack OverDrive
Sonido de alta ganancia de cabezal de amplificacin original de Zoom. Simulacin del Boss OD-1, pionero en el concepto de saturacin.
TS808 Centaur
Simulacin del conocido Ibanez TS808 utilizado por Simulacin del KLON Centaur muy apreciado entre los
muchos guitarristas como realzador. profesionales y utilizado tambin como realzador.
ZOOM G9.2tt 65
speG9.book Page 66 Thursday, March 16, 2006 9:52 PM
Guv'nor RAT
Simulacin del efecto de distorsin Guv'nor de Marshall. Simulacin del PROCO Rat famoso por su cortante
sonido de distorsin.
DS-1 dist +
Simulacin de la distorsin Boss DS-1, una de los Simulacin del MXR distortion+ que populariz la
grandes favoritas. distorsin.
HotBox FuzzFace
Simulacin del Fuzz Face que se convirti en parte de la
Simulacin del previo a vlvulas HotBox de Matchless. historia del rock con su extrao aspecto e increble sonido.
BigMuff MetalZone
Simulacin del Electro-Harmonix Big Muff, preferido de Simulacin del sonido clsico del pedal METALZONE
muchos artistas por su dulce y grueso sonido fuzz. famoso por su prolongado sustain y rango de medios.
TS+F_Cmb SD+M_Stk
Combinacin del sonido de un amplificador de tipo torre
Combinacin de sonido de combo Fender e Ibanez TS-9. y del Boss SD-1.
FZ+M_Stk Z OD
Combinacin de sonido Fuzz Face y del de un Saturacin original de Zoom con distorsin natural.
amplificador de tipo torre Marshall.
ExtremeDS DigiFuzz
Sonido de alta ganancia con la mxima ganancia posible Ataque fuzz de alta ganancia.
en cualquier efecto de distorsin.
Z Clean
Sonido limpio directo original de Zoom.
Los 43 tipos de efectos anteriores tienen los mismos parmetros.
GAIN LEVEL
Gain 0 100 Level 1 100
Ajusta la ganancia de previo Ajusta el nivel de la seal
(profundidad de distorsin). despus de pasar por el mdulo.
PARM1 PARM2
Tone 0 30 Chain Pre, Post
Elige la posicin de conexin
de la seccin de previo. Los
Ajusta la calidad tonal del ajustes disponibles son "Pre"
sonido. (antes del mdulo MOD/
EFX2) o "Post" (despus del
mdulo DELAY).
Aco. Sim
Este efecto hace que una guitarra elctrica suene como
una acstica.
GAIN LEVEL
Top 0 10 Level 1 100
Ajusta el tono especial de Ajusta el nivel de la seal
cuerda caracterstico de una despus de pasar por el
guitarra acstica. mdulo.
PARM1 PARM2
Body 0 10 Chain Pre, Post
Elige la posicin de conexin
de la seccin de previo. Los
Ajusta el caracterstico sonido
ajustes disponibles son "Pre"
de caja de una guitarra
(antes del mdulo MOD/
acstica.
EFX2) o "Post" (despus del
mdulo DELAY).
66 ZOOM G9.2tt
speG9.book Page 67 Thursday, March 16, 2006 9:52 PM
Mdulo EQ
Es un ecualizador de 6 bandas. En el modo de edicin, el mdulo se ajusta utilizando los
mandos [BASS], [MIDDLE], [TREBLE] y [PRESENCE] de la seccin de pr evio y los mandos de
parmetros 3 y 4.
BASS MIDDLE TREBLE PRESENCE
Low-Mid 12 Harmonics 12
400Hz 12kHz
Ajusta el realce/corte en el Ajusta el realce/corte en el
rango de medios-graves. rango de armnicos.
Mdulo CABINET
Este efecto simula el sonido que se consigue al grabar la seal de un recinto acstico captada
por un micrfono. Puede elegir el tipo de micro simulado y su posicin. El estado on/off de este
mdulo controla la seleccin automtica del algoritmo del mdulo PRE-AMP ( p. 65).
PARM1 PARM2 PARM3
Mdulo MOD/EFX2
Incluye efectos de modulacin como chorus y flanger, efectos de retardo y efectos de
modulador de tono.
Chorus
Este efecto mezcla el sonido original con un componente de tono modificado variable, produciendo un sonido
totalmente resonante.
PARM1 PARM2 PARM3 PARM4
Depth 0 100 Rate 1 50 Tone 0 10 Mix 0 100
Ajusta el nivel del sonido con
Ajusta la profundidad del Ajusta la velocidad de Ajusta la calidad tonal del
efectos que es mezclado con el
efecto. modulacin. sonido.
sonido original.
ST-Chorus
Esto es un chorus stereo con un sonido limpio.
PARM1 PARM2 PARM3 PARM4
Depth 0 100 Rate 1 50 Tone 0 10 Mix 0 100
Ajusta el nivel del sonido con
Ajusta la profundidad del Ajusta la velocidad de Ajusta la calidad tonal del
efectos que es mezclado con el
efecto. modulacin. sonido.
sonido original.
ZOOM G9.2tt 67
speG9.book Page 68 Thursday, March 16, 2006 9:52 PM
Ensemble
Es un bloque de chorus con movimiento tridimensional.
PARM1 PARM2 PARM3 PARM4
Depth 0 100 Rate 1 50 Tone 0 10 Mix 0 100
Ajusta la profundidad del Ajusta la velocidad de Ajusta la calidad tonal del Ajusta el nivel del sonido con
efectos que es mezclado con el
efecto. modulacin. sonido. sonido original.
ModDelay
Es un retardo que le permite el uso de modulacin.
PARM1 PARM2 PARM3 PARM4
1
Time 2000 FeedBack 0 100 Rate 1 50 Mix 0 100
mS
Ajusta la cantidad de
realimentacin. Cuanto mayor Ajusta el nivel del sonido con
Ajusta la calidad tonal del
Ajusta el tiempo de retardo. sea el valor, ms alto ser el efectos que es mezclado con el
nmero de repeticiones del sonido.
sonido original.
sonido retardado.
Flanger
Este efecto produce un sonido resonante totalmente ondulante.
PARM1 PARM2 PARM3 PARM4
PitchShift
Este efecto hace que aumente o disminuya el tono del sonido original.
PARM1 PARM2 PARM3 PARM4
PedalPitch
Este efecto le permite utilizar un pedal para modificar el tono en tiempo real.
PARM1 PARM2 PARM3 PARM4
Color 18 Mode Up, Down Tone 0 10 PdlPosi 0 100
Ajusta la cantidad en la que ser
Elige el tipo de cambio de Elige la direccin del cambio modificado el tono.
Ajusta la calidad tonal del Dependiendo del ajuste "Color",
tono realizado por el pedal de tono (hacia arriba o up y tambin se ver afectado el
sonido.
(vea la tabla 1). hacia abajo o down). balance de mezcla entre sonido
original y sonido con efectos.
[Tabla 1]
Color Modo Valor mnimo pedal Valor mximo pedal Color Modo Valor mnimo pedal Valor mximo pedal
Up -100 cent Solo sonido original Up -1 octava + SECO +1 octava + SECO
1 Down Solo sonido original -100 cent 5 Down +1 octava + SECO -1 octava + SECO
Up DOBLAJE Desafinacin + SECO Up -700 cent + SECO +500 cent + SECO
2 Down Desafinacin + SECO DOBLAJE 6 Down +500 cent + SECO -700 cent + SECO
Up 0 cent +1 octava Up - (0 Hz) + SECO +1 octava
3 Down +1 octava 0 cent 7 Down +1 octava - (0 Hz) + SECO
Up 0 cent -2 octavas Up - (0 Hz) + SECO +1 octava + SECO
4 Down -2 octavas 0 cent 8 Down +1 octava + SECO - (0 Hz) + SECO
68 ZOOM G9.2tt
speG9.book Page 69 Thursday, March 16, 2006 9:52 PM
Vibe
Efecto de vibrato automtico.
PARM1 PARM2 PARM3 PARM4
Depth 0 100 Rate 0 50 Tone 0 10 Balance 0 100
Ajusta el balance de mezcla
Ajusta la profundidad del Ajusta la velocidad de Ajusta la calidad tonal del
entre el sonido original y el
efecto. modulacin. sonido.
sonido con efectos.
Step
Efecto especial que modifica el sonido siguiendo un patrn en escalera.
PARM1 PARM2 PARM3 PARM4
Depth 0 100 Rate 0 50 Resonance 0 10 Shape 0 10
Ajusta la profundidad del Ajusta la velocidad de Ajusta la intensidad de la Ajusta el efecto de la
efecto. modulacin. resonancia. envolvente sobre el sonido.
Delay
Es un retardo cuyo ajuste mximo es 2000 ms.
Para consultar los parmetros de efectos, vea TapeEcho (el siguiente efecto).
TapeEcho
Este efecto simula un eco de cinta.
PARM1 PARM2 PARM3 PARM4
1
Time 2000 FeedBack 0 100 HiDamp 0 10 Mix 0 100
mS
Ajusta la cantidad de
Ajusta la atenuacin de
realimentacin. Cuanto mayor Ajusta el balance de mezcla
agudos del sonido retardado.
Ajusta el tiempo de retardo. sea el valor mayor ser el entre el sonido original y el
Cuanto menor sea el valor ms
nmero de repeticiones del sonido con efectos.
suave ser el sonido retardado.
sonido retardado.
DynamicDelay
Es un retardo dinmico en el que el volumen del efecto vara dependiendo del nivel de la seal de entrada.
PARM1 PARM2 PARM3 PARM4
1
Time Amount FeedBack Sense -10 -1,
2000 0 100 0 100
1 10
mS
Ajusta la sensibilidad del efecto.
Para valores positivos, el volumen
del sonido con efectos aumenta al
Ajusta el balance de mezcla
Ajusta la cantidad de aumentar el nivel de la seal de
Ajusta el tiempo de retardo. entre el sonido original y el
realimentacin. entrada. Con valores negativos, el
sonido con efectos.
volumen del sonido con efectos
disminuye al aumentar el nivel de
la seal de entrada.
ZOOM G9.2tt 69
speG9.book Page 70 Thursday, March 16, 2006 9:52 PM
DynamicFlang
Es un flanger dinmico en el que el volumen del efecto vara dependiendo del nivel de la seal de entrada.
PARM1 PARM2 PARM3 PARM4
MonoPitch
Es un modulador de tono monofnico (interpretaciones de notas sueltas), con una baja fluctuacin de sonido.
PARM1 PARM2 PARM3 PARM4
Shift -24 +24 Tone 0 10 Fine -25 25 Balance 0 100
Realiza un ajuste preciso de la
Ajusta en semitonos la Ajusta el balance de mezcla
Ajusta la calidad tonal del cantidad de modulacin de
cantidad de modulacin de entre el sonido original y el
sonido. tono en centsimas (1/100
tono. sonido con efectos.
semitono).
PdlMonoPitch
Es un modulador de tono monofnico (interpretaciones de notas sueltas), que le permite modular el tono en tiempo
real con un pedal de expresin.
PARM1 PARM2 PARM3 PARM4
Color 18 Mode Up, Down Tone 0 10 PdlPosi 0 100
Ajusta la cantidad en la que
ser modificado el tono.
Elige el tipo de cambio de Elige la direccin del cambio Dependiendo del ajuste
Ajusta la calidad tonal del
tono realizado por el pedal de tono (hacia arriba o up y "Color", tambin se ver
sonido.
(vea la tabla 1). hacia abajo o down). afectado el balance de mezcla
entre el sonido original y los
efectos.
70 ZOOM G9.2tt
speG9.book Page 71 Thursday, March 16, 2006 9:52 PM
Cry
Este efecto modifica el sonido igual que un modulador de voz.
PARM1 PARM2 PARM3 PARM4
ReverseDelay
Es un retardo especial en el que los efectos suenan como si estuvieran siendo reproducidos al revs.
PARM1 PARM2 PARM3 PARM4
10
Time 1000 FeedBack 0 100 HiDamp 0 10 Balance 0 100
BendChorus
Este efecto le ofrece una inflexin tonal que utiliza la seal de entrada como disparador y procesa cada nota individualmente.
PARM1 PARM2 PARM3 PARM4
Depth -50 50 Attack 1 10 Release 1 10 Balance 0 100
Ajusta el tiempo de ataque Ajusta el tiempo de salida para
para el efecto de inflexin. el efecto de inflexin. Cuanto Ajusta el balance de mezcla
Ajusta la profundidad del
Cuanto mayor sea el valor de mayor sea el valor de este entre el sonido original y el
efecto.
este parmetro ms lento ser parmetro ms lenta ser la sonido con efectos.
el ataque. salida.
CombFilter
Este efecto utiliza las caractersticas de un combo generado usando una modulacin fi ja en el flanger como un ecualizador.
PARM1 PARM2 PARM3 PARM4
Frequency 1 50 Resonance -10 10 HiDamp 0 10 Mix 0 100
Ajusta el nivel de mezcla entre
Ajusta la frecuencia que ser Ajusta la intensidad de Ajusta la atenuacin de
el sonido original y el sonido
enfatizada. resonancia. agudos del sonido con efectos.
con efectos.
Air
Este efecto reproduce el ambiente de una sala, para crear una profundidad espacial.
PARM1 PARM2 PARM3 PARM4
Size 1 100 Reflex 0 10 Tone 0 10 Mix 0 100
Ajusta el nivel de mezcla entre
Ajusta el tamao del espacio Ajusta la cantidad de Ajusta la calidad tonal del
el sonido original y el sonido
simulado. reflexiones. sonido.
con efectos.
ZOOM G9.2tt 71
speG9.book Page 72 Thursday, March 16, 2006 9:52 PM
Mdulo DELAY
Es un mdulo de retardo que le permite utilizar la funcin de mantenimiento. Los
parmetros de efectos estn descritos abajo, despus de los tipos de efectos.
Delay
Es un retardo con un ajuste mximo de 5000 ms.
PingPongDly
Es un retardo de tipo ping-pong en el que el sonido retardado va alternando entre la izquierda y la derecha.
Echo
Simula un eco de cinta con una duracin de hasta 5000 ms.
PingPongEcho
Es un retardo de tipo ping-pong en el que el sonido retardado va alternando entre la izquierda y la derecha. La
duracin del retardo puede ser de hasta 5000 ms.
AnalogDelay
Simula un retardo analgico con una duracin de hasta 5000 ms.
Los 5 tipos de efectos anteriores tienen los mismos parmetros.
PARM1 PARM2 PARM3 PARM4
Time 1 HiDamp
FeedBack 0 100 0 10 Mix 0 100
5000
Ajusta el balance de mezcla
Ajusta la cantidad de Ajusta la atenuacin de
Ajusta el tiempo de retardo. entre el sonido original y el
realimentacin. agudos del sonido con efectos.
sonido con efectos.
ReverseDelay
Es un retardo inverso con una duracin de hasta 2500 ms.
PARM1 PARM2 PARM3 PARM4
Time 10 HiDamp
FeedBack 0 100 0 10 Balance 0 100
2500
Ajusta el balance de mezcla
Ajusta la cantidad de Ajusta la atenuacin de
Ajusta el tiempo de retardo. entre el sonido original y el
realimentacin. agudos del sonido con efectos.
sonido con efectos.
Air
Este efecto reproduce el ambiente de una sala, para crear una profundidad espacial.
PARM1 PARM2 PARM3 PARM4
Size 1 100 Reflex 0 10 Tone 0 10 Mix 0 100
Ajusta el nivel de mezcla entre
Ajusta el tamao del espacio Ajusta la cantidad de Ajusta la calidad tonal del
el sonido original y el sonido
simulado. reflexiones. sonido.
con efectos.
72 ZOOM G9.2tt
speG9.book Page 73 Thursday, March 16, 2006 9:52 PM
Mdulo REVERB
Este mdulo incluye varios tipos de reverb, reflexiones iniciales y retardos multifase. Los
parmetros de efectos estn descritos abajo, despus de los tipos de efectos.
Hall
Esta reverb simula la acstica de una sala de conciertos.
Room
Esta reverb simula la acstica de una habitacin.
Spring
Este efecto simula una reverb de muelles.
Arena
Este efecto reverb simula la acstica de una gran sala de actuaciones como un pabelln de deportes, por ejemplo.
TiledRoom
Simula la acstica de una habitacin alicatada (tipo bao/cocina).
ModernSpring
Este efecto simula una reverb de muelles con un sonido brillante.
Los seis tipos de efectos anteriores tienen los mismos parmetros.
PARM1 PARM2 PARM3 PARM4
Decay 1 30 PreDelay 1 100 Tone 0 10 Mix 0 100
Ajusta el retardo entre la Ajusta el nivel de mezcla entre
Ajusta la duracin de la Ajusta la calidad tonal del
entrada del sonido original y el el sonido original y el sonido
reverb. sonido.
inicio del sonido de la reverb. con efectos.
E/Reflection
Este efecto aisla solo los componentes de reflexiones iniciales de la reverb.
PARM1 PARM2 PARM3 PARM4
Decay 1 30 Shape 10 Tone 0 10 Mix 0 100
Ajusta la envolvente del
sonido con efectos. En el
rango negativo, se invierte la Ajusta el nivel de mezcla entre
Ajusta la duracin de la Ajusta la calidad tonal del
envolvente. Con un ajuste de el sonido original y el sonido
reverb. sonido.
0, el efecto es una reverb con con efectos.
puerta. En el rango positivo, es
una envolvente de atenuacin.
MultiTapDly
Este efecto produce varios componentes con distintos tiempos de retardo.
PARM1 PARM2 PARM3 PARM4
ZOOM G9.2tt 73
speG9.book Page 74 Thursday, March 16, 2006 9:52 PM
PanDelay
Es un retardo stereo con un tiempo de retardo de hasta 3000 ms.
PARM1 PARM2 PARM3 PARM4
L50 L2,
Time 1 HiDamp
FeedBack 0 100 0 10 Pan 0,
3000
R2 R50
Ajusta la cantidad de Ajusta la atenuacin de Ajusta la posicin de panorama
Ajusta el tiempo de retardo.
realimentacin. agudos del sonido con efectos. (izquierda/derecha) del sonido.
PingPongDly
Es un retardo con un tiempo de retardo de hasta 3000 ms.
Para consultar los parmetros de efectos, vea PingPongEcho (el siguiente efecto).
PingPongEcho
Es un retardo de tipo ping-pong en el que el sonido retardado va alternando entre la izquierda y la derecha. La
duracin del retardo puede ser de hasta 3000 ms.
PARM1 PARM2 PARM3 PARM4
AutoPan
Este efecto desplaza cclicamente la posicin de panorama del sonido.
PARM1 PARM2 PARM3 PARM4
L50 L2,
Width 0, Rate 0 50 Depth 0 10 Wave 0 10
R2 R50
Elige una forma de onda para la
modulacin. Cuanto mayor sea
Ajusta el rango de movimiento Ajusta la velocidad de Ajusta la profundidad de
el valor, mayor ser la
de la posicin del sonido. modulacin. modulacin.
saturacin de los picos de onda,
lo que reforzar el efecto.
74 ZOOM G9.2tt
speG9.book Page 75 Thursday, March 16, 2006 9:52 PM
Mdulo TOTAL
Este mdulo incluye los parmetros que afectan a todo el programa.
TOTAL
Especifica el tempo del programa y la accin del pedal de disparo de funcin 1/2.
PARM1 PARM2 PARM3
NAME
Especifica el nombre del programa ( p. 27).
ARRM
Realiza los ajustes para la funcin ARRM ( p. 52). Utilice la tecla [PAGE] para cambiar entre las pginas 1 y 2.
PAGE1
PARM1 PARM2 PARM3
min (valor Vea la MAX (valor Vea la
ARRM control target
mnimo) pgina 52 mximo) pgina 52
Elige el destino de control
Especifica el valor que tendr Especifica el valor que tendr
ARRM. Cuando est
el parmetro cuando la forma el parmetro cuando la forma
seleccionado el ajuste "NOT
de onda de control alcance su de onda de control alcance su
Assign", la funcin ARRM
punto ms bajo. punto ms alto.
estar desactivada.
PAGE2
PARM1 PARM2
ZOOM G9.2tt 75
speG9.book Page 76 Thursday, March 16, 2006 9:52 PM
Resolucin de problemas
No hay sonido o el volumen es muy bajo Ajuste el control [TUBE] de la seccin del
Compruebe que el interruptor POWER est Accelerator a un valor inferior al obtenido al
en la posicin on. colocar este control en la posicin de las 3
Pruebe a ajustar el mando LEVEL. en punto.
Asegrese de que est correctamente El Accelerator tambin funciona en el estado
conectada la guitarra a la toma INPUT, y el bypass.
amplificador de guitarra a la toma OUTPUT
L/MONO ( OUTPUT R). Elevados niveles de ruido
Compruebe que el blindaje del cable no est Utilice solo un adaptador ZOOM CA.
daado. Ajuste el valor ZNR.
Ajuste el nivel del programa ( p. 16). Desplcese por la habitacin para localizar
Compruebe que el G9.2tt no est en el modo ruidos RF relacionados con las pastillas, etc.
de anulacin ( p. 21). Disminuya el ajuste de los parmetros Gain
En algunos programas puede ajustar el y Level del mdulo PRE-AMP.
volumen con el pedal de expresin. Revise los ajustes de los pedales de
Compruebe que ha seleccionado un ajuste de expresin 1/2 ( p. 33 35).
volumen correcto con el pedal. Dependiendo de los parmetros asignados a
Cuando ambos controles de la seccin los pedales de expresin 1/2, una variacin
Accelerator estn al mnimo no habr del pedal que provoque un cambio drstico
sonido. Debe subir parcialmente al menos de parmetro puede dar lugar a ruidos.
uno de ellos.
No se puede enviar o recibir mensajes MIDI
El sonido est distorsionado Compruebe que estn conectados
Disminuya el ajuste de los parmetros Gain correctamente el conector MIDI IN del
y Level del mdulo PRE-AMP. G9.2tt y la toma MIDI OUT de la otra
Reduzca el ajuste de los controles [TUBE] y unidad MIDI y el conector MIDI OUT del
[BOOST]de la seccin del Energizer. G9.2tt y la toma MIDI IN de la otra unidad.
Reduzca el ajuste del control [TUBE] de la Revise el ajuste del canal MIDI ( p.43).
seccin del Accelerator. Compruebe si est activado el envo/
recepcin del tipo de mensaje MIDI
Los pedales de disparo no funcionan respectivo ( p. 44, 47).
correctamente
Revise el ajuste de los pedales de disparo de La conmutacin On/off con el pedal de
funcin 1/2 ( p. 38). expresin no funciona correctamente
Compruebe el modo operativo actual. La Compruebe que el parmetro 4 (on/off de
accin del pedal de disparo es distinta en el mdulo) del pedal de expresin 1 (P1-1 a P1-
modo de reproduccin y en el modo manual. 4) o el funcionamiento del pedal de
expresin del pedal 2 en direccin vertical
El sonido en el estado bypass es raro (P2V1 a P2V4) estn ajustados a "Enable" en
el mdulo TOTAL ( p. 33, 34).
Reduzca el ajuste de los controles [TUBE] y
[BOOST]de la seccin del Energizer. La funcin de activacin/desactivacin de
mdulo no est disponible para el pedal 2 en
El Energizer tambin funciona en el estado
direccin horizontal (P2H1 a P2H4)( p. 34).
bypass.
76 ZOOM G9.2tt
speG9.book Page 77 Thursday, March 16, 2006 9:52 PM
Especificaciones tcnicas
Nmero tipos de efectos 106
Nmero mdulos efectos 10 mdulos simultneamente
Memoria de programas Area de usuario: 5 programas x 20 bancos = 100 (lectura/escritura)
Area prefijada: 5 programas x 20 bancos = 100 (solo lectura)
Total: 200 programas
Frecuencia de muestreo 96 kHz
Conversin A/D 24 bits, 64x
Conversin D/A 24 bist, 128x
Procesado de seal 32 bits
Respuesta de frecuencia 20 Hz - 40 kHz +1.0 dB, -3.0 dB (con 10 kilohmios de carga)
Interface USB
Interface PC 16 bits (configuracin stereo para grabacin/reproduccin)
Frecuencias de muestreo 32 kHz, 44.1 kHz, 48 kHz
Peso 5.5 kg
ZOOM G9.2tt 77
speG9.book Page 78 Thursday, March 16, 2006 9:52 PM
Especificaciones tcnicas
78 ZOOM G9.2tt
speG9.book Page 79 Thursday, March 16, 2006 9:52 PM
Especificaciones tcnicas
ZOOM G9.2tt 79
speG9.book Page 80 Thursday, March 16, 2006 9:52 PM
ZOOM CORPORATION
ITOHPIA Iwamotocho 2chome Bldg. 2F, 2-11-2, Iwamoto-cho,
Chiyoda-ku, Tokyo 101-0032, Japan
Pgina web: http://www.zoom.co.jp
G9.2tt - 5005-1
spG9flyerE.fm Page 1 Fr day, March 17, 2006 10:02 PM
3 4
[Tabla 2] La tabla de abajo le muestra un ejemplo de funcionamiento del pedal Z cuando la direccin vertical est
ajustada a "PdlPosi V" y la horizontal a "PdlPosi H". Ajuste del giro del pedal de expresin
Direccin Direccin Direccin Direccin
Color min horizontal max Color vertical min horizontal max
vertical
2
max
min
+1 octava
0 centsimas
1500 centsimas
300 centsimas
6
max
min
+1 octava
0 centsimas
+2 octava
0 centsimas 1 Coloque en la posicin de puntera arriba
el pedal de expresin 2 situado en la
La abertura para el ajuste del
max 300 centsimas +1 octava max +1 octava - (0 Hz) pedal es visible en el panel
3 min 0 centsimas 0 centsimas 7 min 0 centsimas 0 centsimas parte derecha de la unidad. trasero del pedal de expresin 2.
max 500 centsimas +1 octava max 500 centsimas -1 octava
4 min 0 centsimas 0 centsimas 8 min -700 centsimas +1 octava
Z-Talking
Este efecto transforma el sonido de guitarra en una voz. Cuando utilice el pedal Z, puede modifi car la vocalizacin de
distintas formas moviendo el pedal en direccin horizontal o vertical.
Pruebe a asignar la direccin vertical del pedal Z (P2V1 - P2V4) al parmetr o "Formant V" y la direccin horizontal
Apretar
(P2H1 - P2H4) al parmetro "Formant H".
PARM1 PARM2 PARM3 PARM4
2 Introduzca una llave Allen de 3 mm en la
abertura de la parte exterior del panel. Para
Variation 15 Tone 0 10 Formant V 0 100 Formant H 0 100 aumentar la resistencia del pedal, gire la llave
Ajusta las modulaciones Ajusta las modulaciones hacia la derecha y para disminuirla, grela
Elige el tipo de variacin de silbicas [picos del espectro de silbicas [picos del espectro de
sonido producido por el pedal Ajusta el tono. frecuencias acsticas que frecuencias acsticas que hacia la izquierda.
(vea la tabla 3). caracteriza la vocalizacin] caracteriza la vocalizacin] soltar
(direccin vertical del pedal). (direccin horizontal del pedal)
[Tabla 3] La tabla de abajo le muestra un ejemplo de funcionamiento del pedal Z cuando la direccin vertical est
ajustada a "Formant V" y la horizontal a "Formant H".
Variacin Direccin
Direccin
horizontal Variacin Direccin
Direccin
horizontal
Ajuste del giro horizontal para el pedal de expresin 1/2
vertical min max vertical min max
1
max
min
i
a
u
e
4
max
min
o
e
a
i 1 Apague el G9.2tt, desconecte
el adaptador CA de la unidad y Llave Allen de 3 mm 40 mm o ms
max u e max a i
2 5
min i o min o u colquela boca abajo.
max e o
3 min u a
3 4
[Tabla 2] La tabla de abajo le muestra un ejemplo de funcionamiento del pedal Z cuando la direccin vertical est
ajustada a "PdlPosi V" y la horizontal a "PdlPosi H". Ajuste del giro del pedal de expresin
Direccin Direccin Direccin Direccin
Color min horizontal max Color vertical min horizontal max
vertical
2
max
min
+1 octava
0 centsimas
1500 centsimas
300 centsimas
6
max
min
+1 octava
0 centsimas
+2 octava
0 centsimas 1 Coloque en la posicin de puntera arriba
el pedal de expresin 2 situado en la
La abertura para el ajuste del
max 300 centsimas +1 octava max +1 octava - (0 Hz) pedal es visible en el panel
3 min 0 centsimas 0 centsimas 7 min 0 centsimas 0 centsimas parte derecha de la unidad. trasero del pedal de expresin 2.
max 500 centsimas +1 octava max 500 centsimas -1 octava
4 min 0 centsimas 0 centsimas 8 min -700 centsimas +1 octava
Z-Talking
Este efecto transforma el sonido de guitarra en una voz. Cuando utilice el pedal Z, puede modifi car la vocalizacin de
distintas formas moviendo el pedal en direccin horizontal o vertical.
Pruebe a asignar la direccin vertical del pedal Z (P2V1 - P2V4) al parmetr o "Formant V" y la direccin horizontal
Apretar
(P2H1 - P2H4) al parmetro "Formant H".
PARM1 PARM2 PARM3 PARM4
2 Introduzca una llave Allen de 3 mm en la
abertura de la parte exterior del panel. Para
Variation 15 Tone 0 10 Formant V 0 100 Formant H 0 100 aumentar la resistencia del pedal, gire la llave
Ajusta las modulaciones Ajusta las modulaciones hacia la derecha y para disminuirla, grela
Elige el tipo de variacin de silbicas [picos del espectro de silbicas [picos del espectro de
sonido producido por el pedal Ajusta el tono. frecuencias acsticas que frecuencias acsticas que hacia la izquierda.
(vea la tabla 3). caracteriza la vocalizacin] caracteriza la vocalizacin] soltar
(direccin vertical del pedal). (direccin horizontal del pedal)
[Tabla 3] La tabla de abajo le muestra un ejemplo de funcionamiento del pedal Z cuando la direccin vertical est
ajustada a "Formant V" y la horizontal a "Formant H".
Variacin Direccin
Direccin
horizontal Variacin Direccin
Direccin
horizontal
Ajuste del giro horizontal para el pedal de expresin 1/2
vertical min max vertical min max
1
max
min
i
a
u
e
4
max
min
o
e
a
i 1 Apague el G9.2tt, desconecte
el adaptador CA de la unidad y Llave Allen de 3 mm 40 mm o ms
max u e max a i
2 5
min i o min o u colquela boca abajo.
max e o
3 min u a
The amp channel indicated by shading will be selected when the patch is called up.
The Z-pedal setting indicates the effect type name and the parameter name. Expression pedal 1 is always assigned to the Volume parameter.
DEMO The symbol indicates the vertical direction setting and the symbol the horizontal direction setting.
An effect listed in brackets ( ) in the Z-pedal setting can be turned on by depressing the pedal fully. MODELING
Patch name PRE-AMP PRE-AMP Patch name PRE-AMP PRE-AMP
For LIVE use For REC use CHANNEL A CHANNEL B FUNCTION1 FUNCTION2 Z-Pedal ( Expression pedal 2 )
For LIVE use For REC use CHANNEL A CHANNEL B FUNCTION1 FUNCTION2 Z-Pedal ( Expression pedal 2 )
G9 Drive DZ Clean PV Drive A/B Phaser on Z-MonoPitch : PdlPosi V ( +1 Oct ) Z-MonoPitch : PdlPosi H ( +2 Oct ) HiWatt HW Clean HW Clean A/B DelayTAP Delay : Mix Chorus : Mix
This patch simulates the new-generation warming sound of Rage Against The Machine guitarist Tom Morello. Moving the Z-pedal in the vertical direction gives a 1-octave higher pitch change, and the This patch is modeled on the clean tone of the Hiwatt Custom 100 with its lively midrange. The typical saturation characteristics of a tube amp are
u0 -1 v0 -1 horizontal direction adds one more octave, for extreme pitch changes. Channel A is modeled on the Diezel Herbert high-gain setting, and channel B on channel 1 clean sound of the Peavey 5150. u3 -2 v3 -2 faithfully preserved, resulting in confident, responsive sound. Immerse yourself in the sultry clean tone of a British amp. Channel B is a tonal variation.
CleanCMB FD Clean VX Clean A/B Hold Delay ModernSpring : Mix AnalogDelay : Mix AC30TBX VX Clean VX Crunch A/B Tremolo on Tremolo : Rate Tremolo : Depth
Ultimate clean tone recreating the saturation of a tube amp. Select either American Fender sound (channel A) or British Vox sound (channel B). By Simulation of the Vox AC30TBX crunch sound with the smooth high range typical of a class A amplifier, and its delicately detailed distortion. When you play a chord, the
u0 -2 v0 -2 making use of the Energizer tube circuitry, the sound can be given additional sheen. u3 -3 v3 -3 sound virtually jumps from the speaker in a way that is just not possible with other amps. Channel A gives the beautiful clean tone that is another hallmark of a class A amp.
CrosOver Z Clean OverDrive A/B BPM TAP AMP-B : Gain Delay : Mix TriAmp HK Clean HK Drive A/B DelayTAP AnalogDelay : Mix AnalogDelay : FeedBack
Versatile overdrive sound very popular in Fusion and Crossover of the nineteen-eighties. When playing a guitar solo, increase the gain by pushing down This patch simulates the smooth drive sound of the Hughes & Kettner Triamp MKII. Let the powerful low end and ample distortion propel your lead play.
u0 -3 v0 -3 the Z-pedal. Add delay by moving the Z-Pedal sideways. Channel A offers Z Clean sound for cutting. u3 -4 v3 -4 Channel A recreates the sound of the class A amp in the clean channel of the Triamp MKII.
X-Phase FD Clean VX Clean A/B Step on X-Phaser : Rate X-Phaser : X-Fade TweedDLX US Blues US Blues A/B BPM TAP E/Reflection : Mix TapeEcho : Mix
Compression + phaser sound great for funky cutting. Cross-fade the regular phaser with the original sound by moving the Z-pedal sideways. Add Sound modeled on the Fender Tweed Deluxe beloved by many Blues greats. Dry crunch sound with just the right amount of sustain brings out delicate
u0 -4 v0 -4 brushing and single-note riffs to really build that groove. Channel A is a clean sound variation based on the Fender Twin Reverb. u3 -5 v3 -5 shifts in dynamics that make all the difference. Lay your heart into those picking nuances. Channel B contains a Tweed Deluxe sound variation.
Wah&Pit! MS #1959 MS Drive A/B PdlMonoPitch on PedalVox : Frequency PdlMonoPitch : PdlPosi Breaker UK Blues UK Blues A/B MultiWah on ( MultiWah : Frequency ) TiledRoom : Mix
This patch is ideal for some tricky guitar play. Use the Z-pedal with one foot and turn into Steve Vai. Control wah with vertical pedal movement and The Marshall Bluesbreaker simulated by this patch is not an amp that provides heavy distortion like the Marshall JCM series. Its crunch sound faithfully follows
u0 -5 v0 -5 operate a mono pitch shifter in real time with horizontal pedal work. Channel A contains the Marshall 1959 crunch sound with moderate gain. u4 -1 v4 -1 each picking nuance and has the classic ring of British Blues in the vein of Eric Clapton. Channel B contains a variation with stronger drive feeling.
Z-Talker OFF FuzzFace A/B DelayTAP Z-Talking : Formant V Z-Talking : Formant H W Fender FD Clean TweedBass A/B ST-Chorus on ST-Chorus : Mix ModernSpring : Mix
Make the guitar talk with the Z-pedal. Moving the pedal in a V-shaped pattern during chord stroking creates a back-up chorus. Or switch to channel B Channel A of this patch contains the clean sound of a Fender Twin Reverb, while channel B recreates the crunch sound of the Fender Bassman. With
u1 -1 v1 -1 with the Fuzz Face sound for stronger impact. Channel A of the REC patch (u1-1) contains Z Clean sound. u4 -2 v4 -2 these two great choices, you can make optimum use of the stereo chorus while playing a wide variety of styles.
'70s Dry TS+F_Cmb SD+M_Stk A/B DelayTAP P-Resonance : Frequency AnalogDelay : Mix
ARTIST
Dry sound reminiscent of the seventies. Gradually moving the Z-pedal vertically brings up from the "woman tone" of Eric Clapton to brighter tone. Channel
u1 -2 v1 -2 A is a combination of Fender combo amp and Ibanez TS-9 crunch sound.
A patch that adds harmony in C major and delay to lead crunch sound. The Z-pedal lets you freely control the mixing ratio of delay and harmonized pitch BlackMor MS #1959 ENGL Drv A/B Booster on Ensemble : Mix Echo : Mix
u1 -4 v1 -4 shifter. Why not try your hand at guitar orchestration using delay tap and the Z-pedal. Channel A is a clean sound based on the same Vox AC30TBX.
Simulation of the famous Ritchie Blackmore sound. Channel A emulates the Marshall 1959 and channel B the ENGL Drv setting for Deep Purple and
u4 -4 v4 -4
AcoJazz Aco.Sim FD Clean A/B Ensemble on Hall : Mix Delay : Mix
Rainbow sound, respectively. Press function foot switch 2 to turn the booster on and get that great tone for lead play.
This patch uses the acoustic effect to modify the sound of an electric guitar in electroacoustic style. The beautiful ambience creates a Jazzy feel. SurfRock FD Clean dist+ A/B BendChorus on X-Vibe : TRM Rate X-Vibe : X-Fade
u1 -5 v1 -5 Recommended for use with single-coil front pickups. Channel B provides the Fender Twin Reverb clean sound.
The ideal sound for playing surf rock in the style of The Shadows or The Ventures. Get those phrases flowing and catch the wave. Move the Z-pedal
u4 -5 v4 -5 sideways to use both phaser and tremolo. Channel B is a dry sound using modeling of dist +.
Smash Rect Mdn DZ Drive A/B Delay on ( Delay : Mix ) Room : Mix
MODELING u5 -1 v5 -1
Simulates the punk rock sound pumped out by Offspring. The drive feeling will make you want to hit those power chords, but the sound still retains
enough crispness for speedy playing. Channel B notches up the aggressiveness with DZ Drive.
MS#1959 MS #1959 MS #1959 A/B Booster on ( Vibe : Rate ) Spring : Mix The Edge HW Clean BigMuff A/B BPM TAP ST-Chorus : Mix Echo : Mix
A patch modeled on the legendary Marshall 1959 SuperLead 100 used extensively by numerous rock guitarists. Enjoy distortion that is slightly different from Simulates the sound of the famous U2 guitarist Edge who jumped onto the world scene in the 1980s. Moving the Z-pedal sideways produces clear echo
u2 -1 v2 -1 modern high-gain stack amps. Pushing the Z-pedal all the way down turns vibrato on. Channel A is a variation of the same amp with lower gain setting. u5 -2 v5 -2 sound. Make optimum use of the pedal for those impressive solos. Channel B offers BigMuff type fuzz sound.
ENGL ENGL Drv ENGL Drv A/B Delay on X-Wah : Frequency X-Wah : X-Fade NotSubtl Z Clean DZ Drive A/B RingModulate on RingModulate : Frequency AnalogDelay : Mix
This patch simulates the sound of the ENGL E650 Ritchie Blackmore Signature 100. Ample distortion but never muddy, that is what Ritchie Blackmore's Simulates the loud and super-distorted sound of Slipknot, a major band on the modern heavy music scene. Moving the Z-pedal vertically gives the sound
u2 -2 v2 -2 sound is all about. Moving the Z-pedal horizontally brings X-WAH into play. Channel A is a variation of the same amp with lower gain setting. u5 -3 v5 -3 a more metallic ring, while the horizontal direction adds ambience for solos. Channel A provides Z Clean sound.
Rectify Rect Cln Rect Vnt A/B Hall on Hall : Mix Chorus : Mix SalasWah Z Clean Guv'nor A/B AutoWah on AutoWah : Resonance Room : Mix
Simulates the high-gain sound of the Mesa Boogie Rectifier, a world-wide standard for heavy music. Warm sound with a strong presence provides a This patch simulates the heavy auto wah sound of Stevie Salas. It uses the compressor + auto wah combination indispensable for true funk. Make free
u2 -3 v2 -3 mighty buildup whether playing riffs or lead. Channel A provides the clean channel sound (Rect Cln). u5 -4 v5 -4 use of brushing and single-note cutting to play those groovy phrases. Channel A contains a clean sound.
J-Chorus JC Clean JC Clean A/B ST-Chorus on ST-Chorus : Mix Hall : Mix BeckOct FD Clean RAT A/B DelayTAP Octave : OctLevel Echo : Mix
A simulation of the Roland JazzChorus sound with its beautiful chorus-based clean tone. Every guitarist needs a transparent clean sound with a wide range of uses, for cutting, arpeggios Simulates the octaver sound cherished by Jeff Beck. It's the ideal patch for playing passages in the fluid driving style of his famous song "Led Boots".
u2 -4 v2 -4 and many other situations. Stereo chorus can be turned on and off with the function foot switch. Channel A offers a tone variation of the same JazzChorus. u5 -5 v5 -5 Adjust the octaver level with the pedal. Channel A provides a Fender Twin Reverb clean sound.
800/2000 MS Crunch MS Drive A/B MultiWah on ( MultiWah : Frequency ) Hall : Mix KingTone FD Clean UK Blues A/B DelayTAP Echo : Mix ModernSpring : Mix
This patch recreates both the Marshall JCM800 and JCM2000. Channel A is modeled on the characteristically solid crunch sound of the JCM800, while channel B brings Clean tone like the choking guitar of the king of Blues, Mr. BB King. Recreate the moody solo from "The Thrill Is Gone", and use the pedal to control the
u2 -5 v2 -5 you the higher gain sound of the JCM2000. Toggle between channels A and B with the function foot switch, for quick access to two types of Marshall sound. u6 -1 v6 -1 ambience. Channel B has a drive sound modeled on the Marshall Bluesbreaker.
Diezel DZ Clean DZ Drive A/B AutoWah on Z-MonoPitch : PdlPosi V ( +1 Oct ) Z-MonoPitch : PdlPosi H ( +1500 Cent )
u3 -1 v3 -1
A simulation of the Diezel Herbert high gain sound popular among guitarists who want that extra heavy impact. Dry and penetrating distortion not available with other amps
sharply etches the outlines also of a heavily down-tuned guitar. Channel A uses "DZ Clean" which simulates the Diezel Herbert channel 1 with ultra-clean, transparent tone.
Manufacturer names and product names mentioned in this document are trademarks or registered trademarks of their respective
owners. The names are used only to illustrate sonic characteristics and do not indicate any affiliation with ZOOM CORPORATION. Continued overleaf
G9.2tt-Patchlist-E-1
G9.2tt Patch List
The amp channel indicated by shading will be selected when the patch is called up.
The Z-pedal setting indicates the effect type name and the parameter name. Expression pedal 1 is always assigned to the Volume parameter.
ARTIST The symbol indicates the vertical direction setting and the symbol the horizontal direction setting.
An effect listed in brackets ( ) in the Z-pedal setting can be turned on by depressing the pedal fully. SPECIAL FX
Patch name PRE-AMP PRE-AMP Patch name PRE-AMP PRE-AMP
For LIVE use For REC use CHANNEL A CHANNEL B FUNCTION1 FUNCTION2 Z-Pedal ( Expression pedal 2 )
For LIVE use For REC use CHANNEL A CHANNEL B FUNCTION1 FUNCTION2 Z-Pedal ( Expression pedal 2 )
Hendrix MS Crunch FuzzFace A/B Phaser on Vibe : Rate Hall : Mix SFX G9 FD Clean BigMuff A/B BPM TAP Z-Step : Frequency Z-Step : Mix
The wild and mighty fuzz sound of guitar god Jimi Hendrix. Push the pedal down and be transported to Woodstock in 1969. Shake the earth with your This patch produces a sound like bubbles forming under water. By moving the Z-pedal, you can make the bubbles burst. When listening with headphones, you'll feel immersed in a liquid universe.
u6 -2 v6 -2 thundering riffs. Channel A of the REC patch(u6-2) simulates the Marshall 1959 sound. u9 -3 v9 -3 As the name "SFX G9" indicates, this kind of sound is possible with the G9 only. Every guitarist is sure to find new inspiration here. Channel B contains dramatic BigMuff type fuzz sound.
Cream Z Clean UK Blues A/B DelayTAP AutoPan : Rate Echo : Mix Pdl-Osc Rect Vnt Rect Vnt A/B DelayTAP Z-Oscillator : Frequency Z-Oscillator : Balance
The Cream hit "Badge" which they also played at their reunion concert is driven by its beautiful melody and an enchanting combination of crunch and rotary speaker sound. That is the This Theremin style sound using the Z-Oscillator is generated when you move the Z-pedal. Expect to be amazed by a sound that goes far beyond what
u6 -3 v6 -3 sound contained in this patch. By assigning multiple effects to the pedal, even the speed control of the rotary speaker is convincingly reproduced. Channel A is a clean sound variation. u9 -4 v9 -4 guitar effects normally offer. Added reverb and delay help to create a fantastic world.
ZZ Drive FZ+M_Stk FZ+M_Stk A/B BPM TAP Delay : Mix Chorus : Mix RingMod FD Clean DZ Crunch A/B Z-Echo on RingModulate : Balance RingModulate : Frequency
Simulates the special drive sound of Billy Gibbons who gained fame as the guitarist of ZZ Top. When you push the Z-pedal hard, delay is added, and Drive sound using the ring modulator. Moving the Z-pedal alters the Z-Echo Time parameter and the RingModulate Frequency parameter assigned to the
u6 -4 v6 -4 horizontal movement adds chorus. Hold your guitar way down low and start the hard boogie. Channel B is high-gain variation. u9 -5 v9 -5 pedal, resulting in a spacy sound. Channel A contains a Fender Twin Reverb clean sound.
u7 -1 v7 -1
Simulates the lead tone of super guitarist Joe Satriani. The sound of the orange Boss DS-1, the quintessential distortion pedal, is a good match for
phrases that require real mastery of technique. Channel B features high-gain Marshall sound. Normal Clean Tube Pre-amp Clean-Tube Mix
LukeCLN Z Clean Rect Vnt A/B DelayTAP Delay : Mix ST-Chorus : Mix
Steve Lukather is largely responsible for the sophisticated sound of Toto that swept the world. In the eighties, he was using the clean tone that is
u7 -2 v7 -2 simulated by this patch. Channel B will let you produce the flashy lead sound of the Mesa Boogie Rectifier. Classic rock'n roll has never sounded better.
This patch simulates the Rockabilly sound of Brian Setzer who became instantly famous for his "Dirty Boogie" album. The quality feel of the sound will
u7 -4 v7 -4 have you swinging in a heartbeat. The TweedBass setting in channel A has reduced gain and a less pronounced tone.
BrianDly VX Crunch ENGL Drv A/B Hold Delay PingPongDly : Mix H.P.S : Mix Recommended settings for major guitar amps
Simulates the sound of guitar magician Brian May who created the dramatic allure of Queen. Use the Z-pedal to blend the alternating right/left delay with the harmonized
u7 -5 v7 -5 pitch shifter to weave some guitar magic. Channel A is a Vox crunch sound suitable for backing. Channel B of the REC patch (u7-5) provides PV Drive sound.
Marshall JCM-2000
KurtDRV Z Clean BigMuff A/B Ensemble on AMP-B : Gain Ensemble : Mix Live performance patches (U0U9, A0A9) Recording patches (u0u9, b0b9)
In the nineties, Kurt Cobain of Nirvana changed the music scene forever, with his grunge sound making dramatic use of distortion and modulation. This
u8 -1 v8 -1
EQUALISATION REVERB CLASSIC GAIN / CHANNEL A EQUALISATION REVERB CLASSIC GAIN / CHANNEL A
patch will make you want to play those riffs from "Smells Like Teen Spirit". Channel A recreates the clean sound for the intro. OFF 4 6 4 6 4 6 4 46 6 4
OFF 46 6 OFF 4 6 4 6 OFF 4 6 4 6 4 6 4 6 4 46 6 4 46 6 4 6 4 6 4 6
OFF OFF OFF OFF
2
0 8 2
2 8 2
5 2 8 2
48 8 2 2 8 8 2 28 8 2
2 8 2
0 8 2
0 8 2
1 2 8 2
58 8 2 2 8 8 2 28 8 2
2 8
This flanger based jet sound is the signature sound of hard rock. Move the Z-pedal in the horizontal direction to adjust the flanger amount. The REC patch (u8-2) 1 2 1 2
u8 -2 v8 -2 BRIGHT 543 98 654 654 BRIGHT 543 54 654 654
10
gives you two fighter planes that cross the stage from right and left when you move the Z-pedal horizontally. Channel A is a clean sound suitable for arpeggios.
876
3
7
876
21
987
321
987
321
876
21
987
321
987
321
8.5 5 5 4.5 5 5
654
21
PedalPan FD Clean DZ Drive A/B Z-Echo on X-Dimension : Depth X-Dimension : Pan
9
10 9 32 10 10 10 9 10 10 10
NORMAL NORMAL
OFF OFF
PdlPhase HW Clean TS808 A/B BPM TAP FixedPhaser : Frequency Echo : Mix HIGH
BRI VOLUME
5
TREBLE
5
MIDDLE
5
BASS
5
HIGH
BRI VOLUME
5
TREBLE
5
MIDDLE
5
BASS
5
This patch produces utterly clean, transparent sound. The Z-pedal allows versatile control of the phaser sound and echo sound. Channel B contains drive
u8 -5 v8 -5 sound modeled on the TS808. LOW OFF
5 5 5
LOW OFF
5 0 10 0~3
This patch produces an enigmatic sound that uses the oscillator effect. The Z-pedal lets you choose between guitar sound and synthesizer sound.
u9 -1 v9 -1 Channel A is a crunch sound modeled on the Fender Bassman. The recommended settings shown above are for the FRONT setting of the amp select feature.
If a recording patch is selected while using a guitar amp, the desired effect may not be obtained and the sound may be unpleasant. Adjust the amp settings using
Bend4T Z Clean JC Clean A/B BPM TAP BendChorus : Balance Hall : Mix the above examples as reference.
Clean sound featuring ZOOM's traditional bend chorus. Play a solo with a Pop style bend, a great match for bands with alluring female vocals. Channel B is a clean The recommended settings shown above may need fine-tuning according to usage condition of the amplifier.
u9 -2 v9 -2 sound variation using JazzChorus. In the REC patch (u9-2), Z-Delay is assigned to the pedal, allowing you to change the position of the delay sound only.
G9.2tt-Patchlist-E-1
USB/Cubase LE Startup Guide USB/Cubase LE Startup Guide
This USB/Cubase LE Startup Guide explains how to install Cubase LE on a computer, how to make the connection and settings of this unit, and how to record your instrument play. Cubase LE Installation Connections and Preparations Recording with Cubase LE
Cubase LE Installation Connections and Preparations Recording with Cubase LE Windows XP Cubase LE Installation Connections and Preparations Recording with Cubase LE MacOS X
To connect this unit to a computer running Windows XP and to To connect this unit to a computer running MacOS X and enable
enable audio input/output, proceed as follows. Start Cubase LE. audio input/output, proceed as follows.
A window asking whether to check the audio input/output port Insert the CD-ROM supplied with this product into the
Install Cubase LE on the computer. appears. Click OK to perform the check.
CD-ROM drive of the Macintosh computer.
When you insert the CD-ROM supplied with this product into the CD- After Cubase LE has started up, access the "Devices" The "Cubase LE" icon appears on the desktop.
ROM drive of the computer, the installer will start up automatically. menu, select "Device Setup..." and click "VST
Follow the on-screen instructions to install Cubase LE. Multitrack" in the list of devices. Double-click the icon to open it, and use the "Cubase
LE Installer" to install Cubase LE.
Connect this unit to the computer using a USB cable.
AC adapter
Guitar or other instrument
Computer If another device is selected, use the pull-down menu to change the
[INPUT] jack selection to "USB Audio CODEC".
When the setting has been made, close Audio MIDI Setup.
or This unit
USB cable
[OUTPUT] jack Start Cubase LE.
Audio system or
other hi-fi playback Check whether "ASIO Multimedia Driver" is selected as ASIO driver
Batteries in the right part of the device setup window.
equipment
HINT
Click the "Control Panel" button in the device setup Connect this unit to the computer using a USB cable. The Cubase LE program is installed in the "Applications" folder.
NOTE window. In the window that appears, click the
If you monitor the audio signal during recording via the audio output "Advanced Options" button. When Cubase LE has started up, access the
of the computer, there will be an audible latency. Be sure to use the In the advanced options window, check whether "USB Audio "Devices" menu, select "Device Setup...", and click
[OUTPUT] jack of this unit to monitor the signal. CODEC" is selected as input port and output port. "VST Multitrack" in the list of devices.
AC adapter
When a device designed to use USB power is powered via the USB Guitar or other instrument Check whether "USB Audio CODEC(2)" is selected as ASIO driver in
cable, insufficient power may result in unstable operation or error Macintosh
[INPUT] jack the right part of the device setup window.
indications appearing on the display. In such a case, power the
device from an AC adapter or batteries.
Use a high-quality USB cable and keep the connection as short as or This unit
USB cable
possible. If power is supplied to a device designed to use USB
power via a USB cable that is more than 3 meters in length, the low [OUTPUT] jack
Audio system or
voltage warning indication may appear. other hi-fi playback
Batteries
equipment
HINT
No special steps are necessary for canceling the USB connection. NOTE
Simply disconnect the USB cable from the computer. If you monitor the audio signal during recording via the audio output
If not selected, click the respective box to place a check mark in it.
When the setting has been made, click the OK buttons to close the of the computer, there will be an audible latency. Be sure to use the
When you connect this unit for the first time to a computer running windows and return to the normal post-startup Cubase LE screen. [OUTPUT] jack of this unit to monitor the signal.
Windows XP, a message saying "New Hardware Found" will appear. When a device designed to use USB power is powered via the USB
Before proceeding, wait a while until this message disappears. cable, insufficient power may result in unstable operation or error
HINT If another item is selected, use the pull-down menu to change
indications appearing on the display. In such a case, power the the selection.
From the "Start" menu, select "Control Panel" and By clicking the Move up/Move down button in the advanced device from an AC adapter or batteries.
double-click "Sounds and Audio Devices". options window, you can change the priority sequence setting of When the setting has been made, click the OK button to close
Use a high-quality USB cable and keep the connection as short as the window.
the currently selected port. If you move "USB Audio CODEC" to the possible. If power is supplied to a device designed to use USB
The sounds and audio devices properties screen appears. Click the
top of the list, it will also be at the top in the following VST input power via a USB cable that is more than 3 meters in length, the low
"Audio" tab and check whether "USB Audio CODEC" is selected as Access the "Devices" menu and select "VST Inputs".
window. voltage warning indication may appear.
default device for audio playback and recording. The VST inputs window appears. Check whether the
When you edit any of the settings in the advanced settings window,
a window asking whether to check the audio input/output port input port is active.
appears. Click OK to perform the check. HINT
No special steps are necessary for canceling the USB connection.
Access the "Devices" menu and select "VST Inputs". Simply disconnect the USB cable from the computer.
The VST inputs window appears. Check whether the
input port is active. Open the "Applications" folder and then the "Utilities"
folder, and double-click "Audio MIDI Setup".
The Audio MIDI Setup screen appears. Active button
Click "Audio Devices" and check whether "USB Audio CODEC" is
Active button selected as default input/default output. If the Active button is Off (grayed out), click the button to set it to On.
If the Active button is Off (grayed out), click the button to set it to On.
Continued overleaf
If another device is selected, use the "Default Device" pull-down
menu to change the selection to "USB Audio CODEC". HINT
When the setting has been made, click the OK button to close the
When multiple input ports are available for selection, you should scroll
sounds and audio devices properties screen.
or enlarge the window and check the enable/disable settings for all
ports.
Continued overleaf
Continued from front Cubase LE Installation Connections and Preparations Recording with Cubase LE Windows XP MacOS X
After specifying the project file save location (such as Access the "Devices" menu and select "VST Inputs".
the desktop), click the OK button (Choose button in
MacOS 10.4). The VST inputs window appears.
A new project is created, and the project window for controlling most
This window shows the available input ports and their active/inactive 1. Move the fader
status. Channel assigned to audio track Master channel of the master
of the Cubase LE operations appears. channel (as
You can perform the following steps here.
4. Raise the fader of
displayed in step the master channel
3. Verify that the Record Standby button is shown in red. (If 15) fully down. to obtain a suitable
the button is grayed out, click the button to enable it. This volume.
2. Verify that the Active button for USB Audio CODEC will set the audio track to the recording standby condition.)
1/2 (USB Audio CODEC L/R on MacOS X) is enabled
(not grayed out). If the button is grayed out, click the
button to enable it.
HINT
When the Record Standby button is enabled, the level meter next to
the fader shows the input level for the audio track. When the button is
disabled, the output level for the audio track is shown.
Go to beginning of project Play button
While playing your instrument, adjust the output level
Project window of this unit to achieve a suitable recording level for 2. Use the controls on the 3. Click the Play button in
transport panel to move to the transport panel to
Cubase LE. the beginning of the project. start playback.
VST input window
To create a new audio track, access the "Project"
menu and select "Add track". In the submenu that 1. When there are multiple input ports,
drag here to enlarge the window.
appears, select "Audio". Level meter HINT
A new audio track is added to the project window. If no sound is heard when you click the Play button after recording,
When the audio track is in recording standby mode, check the settings in the VST input window (step 13) and the master
Connect the guitar or other instrument to the [INPUT] its recording level is shown by the level meter for the channel output port setting (step 15) once more.
jack of this unit and select the desired patch. assigned channel. The level should be set in such a
way that the meter registers to a fairly high value but
The sound selected here will be recorded on the computer via the remains below the maximum point. For optimum enjoyment
[USB] port.
While using Cubase LE, other applications may slow down drastically
Access the "Devices" menu and select "Mixer". NOTE or the message "Cannot synchronize with USB audio interface" may
The level meter shows the signal level after appear. If this happens frequently, consider taking the following steps
The mixer window appears. internal processing by Cubase LE. Therefore to optimize the operation conditions for Cubase LE.
This window shows the channels assigned to created tracks. a slight time lag may occur between playing a
guitar or other instrument and the meter
(1) Shut down other applications besides Cubase LE.
You can perform the following steps here. registering the change in level. This is normal
and not a defect.
In particular, check for resident software and utilities.
The audio tracks of Cubase LE will be
HINT recorded with correct timing exactly matched
(2) Reduce plug-ins (effects, instruments) used by Cubase LE.
You can add several tracks at once by accessing the "Project" menu, to your instrument play. There will be no lag When there is a high number of plug-ins, the computer's
selecting "Add track" and then selecting "Multiple..." in the submenu. between already recorded tracks and newly processing power may not be able to keep up. Reducing
added tracks. the number of tracks for simultaneous playback can also be
helpful.
If applications still run very slowly or the computer itself does not
Transport panel function properly, disconnect this unit from the computer and shut
down Cubase LE. Then reconnect the USB cable and start Cubase LE
If the transport panel is not shown, access the "Transport" menu and again.
select "Transport Panel".
G9.2tt Modeling Description Reference for drive effect types and its original models.
VX Clean
FD Clean US Blues TweedBass
Fender Twin Reverb '65 Fender Tweed Deluxe '53 Fender BASSMAN VOX AC30TBX VX Crunch
In the later half of 1963, a reverb unit was added to the Twin amp, which was the birth of The very first Fender amplifier was developed by Leo Fender and his trusty partner, the Among the many famous Fender amps, the Bassman has earned a special place. When Jim Tracing back the long history of Vox, one finds that it all began in 1958 under the moniker
the Twin Reverb model. In 1965, Fender company was sold to CBS because of Leo engineer Doc Kaufman in 1945-46. Actually, the earliest models were not made under the Marshall developed his original amplifier, he is said to have used the Bassman circuit as a "Jennings Musical Instruments" (JMI). Originally, this company built amps in the ten to
Fenders health problem. The program on this Zoom G series is modeled after the pre-CBS Fender brand but the K&F Manufacturing Corporation named after the Initials of the reference. When it first came out in 1951, the Bassman had an output of 26 watts and used fifteen watt range, but as time went on, the demand for higher-power amps became
Twin Reverb from 1965 aka Black Panel. This amp has four 7025 (12AX7), a 12AX7 two. The first amplifier using the Fender brand was the Model 26 in 1947. In 1949, a single Jensen 15-inch speaker. After various modifications, it reemerged in 1959 with a stronger, leading to the birth of the famous AC30. The original AC30 had two Alnico
and two 12AT7 pre-tubes, four 6L6GC power-tubes and silicon diodes for the rectifier circuit. the entry models called Champion 400/600 series followed. The so-called Tweed Amps 50-watt output and four Jensen 10-inch drivers. The simulation of the Zoom G series is Celestion 12" speakers, an EF86 tube preamp and EL84 tube power section, along with a
The diode rectifier is believed to give a tighter sound to the amplifier than the tube rectifier covered literally with tweeds all over were developed during the 1950s and the 1960s. In modeled on the "bright" channel of the '59 Bassman. Introduced at the 1951 NAMM show GZ34 rectifier. Around this time, the Shadows as well as the Beatles started using the AC30
does, which should be the key to the characteristic glittering sound of this Twin Reverb. these years, the company put out various tweed models like the Bassman or the along with the Precision Bass, this amp was originally intended for use with bass guitars. which quickly became very popular among guitarists. In the following years, musicians
This guitar amplifier has two 12 loudspeakers by Jensen and pus out 80w power. On the Bandmaster. The program of this Zoom G series is modeled after, among others, the But its reedy distortion made it a favorite with some of the early blues giants, and later with wanted even higher gain, and Vox responded with the Top Boost unit, an add-on that was
program in this Zoom G series, you can have the sound with the Bright switch on by most representative Tweed Deluxe aka the Wide Panel from 1953. This amplifier has a many rock guitarists. Of course, the amp continues to used by musicians to this day. later integrated in the AC30TBX. This is the model whose sound is simulated by the Zoom G
tweaking the Harmonics parameter in the 6 band EQ section. When you turn the 12AY7 and a 12AX7 pre-tubes, two 6V6GT power-tubes, a 5Y3GT rectifier tube and a 12 series. After Vox left the JMI stable, sales unfortunately dropped drastically. In recent years,
reverb effect on, you will get that Twin Reverb sound you have been longing for. Jensen loudspeaker and its output power is 10w. Recently the original amplifier is priced Korg has acquired the trademark rights to the Vox name and has started to produce a re-
quite highly and is very difficult to find in good condition. This amp has two inputs but one issue that is faithful to the original sound. The AC30TBX simulation in the Zoom G9.2tt
is the input for a microphone. It has just one tone knob for treble control. Therefore, it is duplicates the Hi gain inputs of the normal channel and brilliant channel. It delivers a clean
advisable to use this program on the Zoom G series with a flat tone setting except for the unsullied sound typical of a class A amplifier as well as smooth overdrive sound.
treble parameter so that you can enjoy the characteristic sound in the lower registers and
the unique sound in the higher registers of the original Fender amp.
Rect Cln
JC Clean HW Clean BG Crunch Rect Vnt
Roland JAZZ CHORUS HIWATT Custom 100 MESA/BOOGIE Mark III MESA/BOOGIE Dual Rectifier Rect Mdn
Simply put, the Roland JC-120 is the most familiar guitar amplifier among both The Custom 100 was the flagship amp from Hiwatt, a British manufacturer that ranks with The origin of the MESA/BOOGIE amplifier was the modified Fender Princeton. Randall The Rectifier was born by improving on the simul power circuit of the Mesa/Boogie Mark 1
professionals and amateurs. Released in 1975 from Roland, this amp became known as Marshall among the British legends. Vintage Hiwatt amplifiers made before the mid-1980s Smith, an amp tech in San Francisco, souped up those small guitar amps to put out 100w to 3 as well as increasing the preamp gain and applying other tweaks. From its five 12AX7
portable, loud and almost trouble-free (which are the very characteristics Japanese use high-grade military-spec parts and hand-soldered point-to-point wiring. This is the power and sold them. The first model was called Mark I. Carlos Santana tried one and preamp tubes and four 6L6GC power tubes, the amp produces an output of 100 watts.
products are known for!). You are pretty sure to find one in any live houses or studios all reason why production was limited to about 40 units per month. Because of their solid said, Shit man, that little thing really Boogies! -which gave the amplifier the brand name Unlike the Mark series, this model gives priority to tone, featuring a tone control circuit after
over the world. The key to that sound of JC-120 is its unique chorus effect: the slightly construction, these amplifiers have been likened to tanks. Their sound, in a word, is the BOOGIE. The second model Mark II had lead and rhythm channels and a 4-band the volume. With this model, the Mesa/Boogie brand image progressed from Fusion to
delayed vibrato sound comes from one of two 12 loudspeakers and the dry sound from epitome of clean. The pre-stage tubes are ECC83, while the power tubes are the same EL34 equalizer to give wider variety to the guitar tone. The special feature of this model was an Metal. The distinguishing feature of this amplifier, and its namesake, is of course the
another and both sounds are combined in the air, which creates that distinctive spacey as used by Marshall. Unlike the glittering clean sound of a Fender amp, the clean sound of a accomplished simul- power circuitry (the operation could be switched between class A and rectifier. The sound provided by this patch is based on the Dual Rectifier model which has
mood. This effect became very popular which is why Roland decided to release the chorus Hiwatt is darker, having that characteristic British tone. Especially in the "normal" channel, class AB). The power amplifier section had six power tubes. When the class A operation is two rectifier circuits, one of which is tube based and one configured with silicone diodes.
circuit independently as the CE-1 pedal. Incidentally, the chorus effect on the Zoom G turning up the volume to maximum will simply increase the sound pressure, without selected, two EL34 power tubes are activated and the amp puts out a really smooth sound. The diodes create a tight, high-powered sound, while the tube sound is more soft and
series is modeled after its follower CE-2. Another unique feature of JC-120 is its Bright breakup or loss of detail. In the high-gain "brilliant" channel, slight distortion is possible by When the class AB operation is selected, these two EL34s and other four 6L6GC power tubes warm. The Zoom G9.2tt simulates the orange channel with its characteristic warmth, and
switch. This function is not included in this modeling program but you can approximate the connecting a guitar with a high-output pickup such as a Les Paul. But the sound always are all activated and the amplifier puts out its full potential power. the high-gain red channel having vintage and modern modes. Both use the silicone diode
effect of this switch by tweaking the Harmonics parameter in the 6 band EQ section. remains detailed and transparent, allowing the listener to clearly pick out the individual Until the model Mark II, MESA/BOOGIE amps were quite expensive, hand-made amplifiers, rectifier, and the cabinet is the same as the Boogie with four Celestion 12" speakers.
notes that make up a chord. The "normal" and "brilliant" channel inputs can be linked with but the next model Mark III was more affordable. It has one 10 loudspeaker and 60w
a short shielded cable, for even higher sound pressure output. output power but retains all of the classic BOOGIE features; simul-power circuitry, the
This effect type simulates the linked sound as described above, much favored by Pete graphic EQ, and three (Rhythm1, Rhythm2 and Lead) separate channels. With this Zoom G
Townshend of The Who and Pink Floyd's David Gilmour. series, you can select the modeling of the combo type of this Mark III.
HK Clean DZ Clean
ENGL Drv PV Drive HK Crunch DZ Crunch
ENGL E650 Ritchie Blackmore Signature 100 PEAVEY 5150 STACK Hughes & Kettner TriAmp MK2 HK Drive
Diezel Herbert DZ Drive
The German-born ENGL started out as a tube combo amp built in the mid-eighties by The 5150 and the 5150 MkII were very famous guitar amplifiers originally developed as Using a total of 13 tubes in the pre and power amp stages, with A and B settings for each, This modern three-channel amp features great tonal versatility, ranging from clean tone to
Edmund Engl. Towards the end of that decade, Heavy Metal ruled the music scene and high- the signature models for Eddie Van Halen. Unfortunately, he doesnt use it anymore this is a monster of an amplifier offering the equivalent of six channels to play with. AMP1 is distortion. In particular, the extremely dry and gritty distortion produced by channel 3 gives
gain amps were in great demand. ENGL rose to the challenge with a full-blown stack amp because of the expiration of the endorsement contract. The program on this Zoom G series a Fender type clean channel with bright and uncluttered sound. AMP2 is a classic British a piercing effect that is hard to produce with any other amp. It is a favorite of Heavy Rock
that caught the attention of professional musicians in Europe and cemented the reputation is modeled after the first version of the 5150. This amplifier has two (Rhythm and Lead) drive channel which covers the overdrive range from crunch to distortion. AMP2 has already bands such as Metallica and Limp Bizkit. The uncluttered sound sharply etches the outlines
of the brand. The head amp E650 uses three ECC83 tubes in the pre section and four 5881 channels and puts out 120w power using five 12AX7 pre-tubes and four 6L6GC power- fairly high gain, but it is surpassed by AMP3. While allowing deep distortion, the sound has also of a heavily down-tuned guitar. A DEEP control allows further boosting of the bass
(6L6GC) tubes in the power section. It has two channels (Clean/Lead), but since it allows tubes. The rectifier circuit employs silicon diodes. The uniqueness of the sound of this a solid core and remains wonderfully detailed. The reason why the TriAmp is so popular frequencies, for sound so low that it seems to hug the ground. The Zoom G9.2tt lets you
overall Lo/Hi gain switching, the amp can also be regarded as a four-channel unit. The Clean amplifier is characterized by its sharp attack, deep and smooth tone, fine distortion and fat among guitar pros is the fact that all three channels offer high-quality sound. The full range achieve the same effect by boosting the BASS control of the EQ module. While the amp is
channel provides a tight, bright Fender style clean sound that is unusual in a stack amp. The and clinging low registers. The program is modeled after the combination of the Lead from clean to high-gain distortion can be covered with a single amp. The Zoom G9.2tt justly famous for its distortion sound, the other channels also provide attractive choices.
Lead channel is more in the Marshall vein, but at higher gain settings, it becomes a unique channel of the 5150 head and a 5150SL, a four-12 cabinet. Just crank up the gain and simulates all three channels, letting you enjoy the same versatility as the monster amp itself. Channel 1 is ultra-clean, and channel 2 has a dry crunch sound with a character that clearly
ENGL sound. But another vital aspect of the ENGL sound is the solid and heavy E412VS play one of Van Halens hit Top Of The World! distinguishes it from Californian amps. The Zoom G9.2tt provides patches modeled on all
cabinet with its 4 x 12" Celestion Vintage 30 speakers. The Zoom G9.2tt simulates the Lead three channels.
channel of the E650 combined with the E412VS.
Such as product names and company names are all (registered) brand names or trade marks of each respective holders, and Zoom Corporation is not associated or affiliated with them. All product names, explanation and images are used for only purpose of identifying the specific products that were referenced during product development.
G9.2tt Modeling Description Reference for drive effect types and its original models.
The OD-1 released by BOSS in 1977 was originally developed for the simulation of the This is modeled on the early Tube Screamer introduced by Ibanez in 1979 for the non-US This pedal is well known for two things: its capability of producing pure distortion without The initial sales talk for this serious distortion pedal Guvnor bearing the Marshall brand
natural overdrive sound of tube amplifiers, but this stomp box turned out to be popular as market. In Japan, it was sold under the Maxon name as the OD808. As the moniker implies, impairing the original sound, and its high price. Being four-and-a-half years in the making, was that you could get the distortion sound of the Marshall amps with this small stomp box.
the booster unit to connect to the input of the real tube amplifier to get tighter and more when using the pedal on its own, it produces natural distortion such as when driving a tube the Centaur distinguishes itself from other famous pedals such as the Ibanez TS808 or the Depending on which guitar amps you combine, you can actually get the Marshall amps
punchy sound with the increased gain. The OD-1 employs the asymmetrical clipper amp hard. But it often was used simply as a booster, with gain at 0 and volume at 10, to Boss OD-1. It is also often used as a booster, but whereas these vintage pedals add their distortion. There are two different versions of the Guvnor: the Britain-made ones from
section in its circuit design that uses three diodes to create the overdrive sound that is mild drive a full-up amp even further. Normally, this would not change the amplifier's sound, but characteristics to the amp sound, the Centaur creates a tone as if it were driven by the amp. 1988 and the Korean-made ones from 1998. The program on this Zoom G series is modeled
and rich in nuances. The pedal had been in production from 1977 to 1985, but now it is a slight peak in the midrange results in a softer tone. after the original version from 1988. The Guvnors characteristic feature is the frequency
unexpectedly difficult to even find a used one. And if you could locate one, it would be This pedal is also famous for being used by blues guitar legend Stevie Ray Vaughan who point you can tweak using the TREBLE control. Even if you lower this parameter value,
astonishingly expensive. There have been many stomp boxes known as overdrive units. The tragically perished in a helicopter crash. the sound will get fat instead of getting dullish. As you raise the value, the sound will get
most famous one is probably the Tube Screamer but we chose this very original overdrive sweeter and clearer.
pedal OD-1. If you are lucky enough to use the real OD-1, we invite you to try blind
test to turn off all of the effect module except the OD-1 on the Zoom G series and
compare the sound of the modeling and that of the real one. We think that you will not
hear any difference.
This is one of the most widely used pedals. It has only three knobs (Distortion, Filter, This orange-colored pedal can be called the standard of distortion sound. Among the many MXR, a company founded in the seventies by two high school students, is famous for stomp The HOT BOX was released as a pedal preamp bearing the MATCHLESS brand. It uses
Volume), but each knob has a wide adjustment range, allowing various types of sound. With distortion pedals from Boss, it is a real long-seller, along with the SD-1. In Japan, sales of boxes such as the Dynacomp and Phase 90. In the early days, their products were actually two 12AX7A tubes for the truthful reproduction of the sound of the MATCHLESS guitar
distortion fully turned up, the fat, up-front sound is close to a Fuzz pedal. At the twelve the pedal ceased at one point (although production for the U.S. market continued), but as of built and painted in a garage and set out to dry in the garden. As the story goes, sometimes amplifiers. It has the compressed sound and the quick response, which are distinctive
o'clock position, the crunch sound brings out those fine picking nuances, allowing the player 2005, the product is available again. This is the only Boss pedal to be reintroduced to the small insects would get stuck on the surface, and the lot would be shipped out as is. The characteristics of tube amps. Its sound is fat and cuts through very well, too. Even if you
to tweak the sound by varying the playing style. As opposed to a regular tone control, the market in this fashion. The sound is trebly and very "distortion-like", but it can very well pedals soon gained worldwide fame in the seventies, but eventually lost their market share crank up the gain to get a distorted sound, you will retain the nuances of the original guitar
filter knob cuts the treble when turned clockwise. This is the secret behind the typical "RAT" hold its own in a band. Favored by Joe Satriani and Nirvana's Kurt Cobain. to "Made in Japan" products from Boss and others that provided high performance at lower sound. Although it is categorized as preamp, the ideal way to get the best possible sound is
sound. In the Zoom G series, this effect is simulated by the TONE parameter, but operation cost. MXR disappeared from the scene, but in the late eighties, Jim Dunlop bought the rights to connect it, like usual stomp boxes, to the input of your guitar amp. Its design is also
is reversed (treble is cut when turned counterclockwise). and is now producing a number of re-issue models. attractive: the case is polished like a mirror and the MATCHLESS logo lights up when you
This pedal much beloved by Randy Rhoads who made the "distortion" moniker and sound turn it on. This Hot Box is literally a magic box: you can get the signature sound of the
famous the world over. The hard-edged tone stays detailed also when playing fast solos or MATCHLESS amps regardless of the guitar amplifier you connect it to.
riffs with the lower strings muted. The world of heavy metal and hard rock wouldn't be the
same without it.
Dallas-Arbiter FUZZ FACE Electro-Harmonix BIG MUFF BOSS MT-2 Fender Combo + TS9
FuzzFace BigMuff MetalZone TS+F_Cmb
FUZZ FACE was originally released from the Dallas-Arbiter company in 1966 encased in a There are several versions of this pedal. The Zoom G series simulation is based on the so- The MT-2 (METAL ZONE) has the strongest distortion. Its unique distortion sound has Opinion may be divided, but it can be argued that the most powerful and fat guitar sound
uniquely designed housing that literally looked like a face. It is also famous as legendary called "Ram's Head" from the early seventies, characterized by very long sustain and rich very fat mid to low range and it has a parametric EQ in addition to the Hi and Low EQs, ever was created by Stevie Ray Vaughan. He did this by putting extremely heavy-gauge
guitarist Jimi Hendrixs favorite gear. He combined this FUZZ FACE with his Marshall distortion tapestry. Major names from the 70's associated with this sound are Carlos which is the key to the scooped metal sound. This stomp box is reputed for its flexibility in strings that would fit an acoustic guitar on his old and battered Stratocaster. Add to this the
amps because it was hard to get distorted sound from them at that time, and created avant- Santana and Robert Fripp of King Crimson. From the late eighties into the nineties, the sound because you can not only get that scooped metal sound by cutting the mid range and full-up Fender amp and a small Ibanez pedal, and you are approaching magic territory. Just
garde tones. The heavy and fat low end and the fuzz sound with long sustain are the grunge movement took over, with Nirvana's Cobain and J. Mascis of Dinosaur Jr. using the boosting the high and low range but also the overdrive sound by reducing the gain and like this effect type does. Connect a Stratocaster and bend the third string near the 14th fret.
characteristics of this effective device. The earliest model used two PNP germanium pedal to do their thing. Compared to an ordinary fuzz pedal, the BIG MUFF offers rich boosting the mid range. This is one of the best-selling stomp boxes among many of the Feel that smile appear on your face. If you want to express your feelings, give this one a go.
transistors and was very different in sound from the later models using silicon transistors. midrange and detailed distortion that maintain presence also when playing chords. The popular line-ups of BOSS products. Once connected, the Strat or the Les Paul will have the
The theory of creating distorted sound is simple. Have you tried to connect the guitar to a result is a wholly unique sound somewhere between distortion and fuzz. MT-2 sound regardless of the types of guitar pickups. It was first introduced in 1991 and
microphone input on your radio cassette recorder to emulate that sound? You cannot go is still in the BOSSs catalog; a truly a long-seller!
too wrong if you think that the circuitry of this device is similar to that. The program on this
Zoom G series is modeled after this earliest version most satisfactorily.
Ever since the dawn of rock, Marshall has been recognized as the best brand of amp for this At the Monterey Pop Festival in 1967, a guitar was smashed and burnt on stage, helped The Bluesbreaker or Bassman are wonderful combo amps, but nowadays, their gain can Which amplifier has the strongest distortion in the world? Is it the Rectifier, the Herbert, the
genre. With the JCM800 series that appeared in the eighties, Marshall again pulled ahead of along by Zippo lighter fluid. Just before this poor Stratocaster gave up the ghost, its seem a little low. Sometimes you just want to combine the transparency and dynamics of TriAmp? No, it is the Z Stack that you find right here. The distortion is so strong that simply
the pack. Among the various models of the series, the most successful must be the 100-watt psychedelic colors disintegrating, it had been played with furious intensity and produced a these combo amps with a more intense level of distortion and sustain. The Z Combo (great touching the fingerboard with your left hand (or right hand if you're left-handed) will
2203 featuring a master volume control. With its crisp and solid sound, it makes the guitar sound unlike anything heard before. And that is also what this effect type, combining a name!) is the answer to your prayers. You get a midrange sound like adding up a Marshall produce sound. (This makes right-hand playing a snap.) But amazingly, a 9th chord will
stand out gloriously in a band even over the vocals, something that hard rock guitarists Marshall SuperLead 100 with the FUZZ FACE from Dallas-Arbiter, attempts to do. It and a Fender and dividing them by two, plus distortion that equals notching up the volume remain clearly identifiable as such, because the sound does not lose its core. The biggest
really appreciate. However, for dashing leads with heavy riffs or right-hand playing, gain produces a wildly deformed sound that is not destined for delicate chords but for audacious from 10 to 15 (or from 12 to 17 on the Bassman). While not intended for jazz or heavy problem of this amplifier is that it does not exist--except in the Zoom G series, that is. Give it
with this amp alone was still not enough. Driving the Marshall JCM800 with an overdrive dramatic leads with heavy sustain. Such as those of the legendary Jimi Hendrix. metal, the sound is great for a wide range of other blues and rock styles. a try if you are after really heavy sound.
pedal was the answer. This effect type recreates the sound of those glitzy hairspray bands
from the eighties, using the Boss SD-1 as overdrive pedal.
When playing an electric guitar, distortion is of course one of the essential style elements, This distortion program is developed especially for the Zoom G series. We deliberately made Forty years ago, my fellow guitar player used to crank up his amp trying to distort his guitar This is a clean sound that makes the drive module virtually disappear. The bass is tight, and
but different guitarists will have different preferences. What this effect type does is use of the characteristics of digital devices and even emphasized the edge of the digital sound and make other guys of the band virtually deaf at the end of the rehearsal. When it a very slight treble emphasis creates vigor. Why choose this effect type, then? Try it when
exemplify the preferences of the Zoom G series developers. The smooth overdrive sound sound to get the distortion to the maximum. The TM-01 (Tri Metal) was the pedal that was difficult to get the distorted sound out of the amplifiers like in those days, some guys creating patches for arpeggios and cutting. You should get smoother and more rounded
should lend itself to many playing styles, allowing finely nuanced changes. Warmth is better had the deepest distortion sound among the stomp boxes from ZOOM but was made cuts in the cone loudspeakers to make the sound distorted, which was the origin of sound. If you want to produce clean guitar sound via a line input, excessive bass may make
than with any stomp box, and loud volume will not cause the sound to become unpleasant. discontinued. It had as much as three diode-clipping stages and had very high gain. The the sound of fuzz effects. The fuzz pedals were developed to reproduce that distortion-like it sound as if the pick got caught between the strings. This effect type should solve such
Just the right amount of sustain ensures that attack dynamics remain vibrant. Tracking your Extreme Distortion is programmed to get the gain even higher. It raises the signal level to sound. In other words, the trick of fuzz effect is to simulate the dirty distortion and that problems.
fingerwork with uncanny accuracy, the effect reproduces even the final tinge of the pick the maximum at the input stage and gets the wild distortion sound at the clipping stage. In broken feel. This Digital Fuzz has the very effect described above. Its drastic
when it leaves the string. We believe that many guitarists will find here what they were fact, you wont change the distortion rate even if you lower the volume on your guitar! Its distortion, relentless cut-offs and noises in the decay are the characteristics that one could
looking for. distortion is that deep. Contrary to the usual distortion effects whose sound gets thinner as simply describe as broken. Its fat and tight sound can be seriously recommended for the
you raise the gain, this Extreme Distortion wont lose the fatness and tightness of the fuzz maniacs to try. This is literally the Digital Dirty Fuzz that is only possible in the digital
sound. domain (are you brave enough to make cuts in your loudspeakers?).
Such as product names and company names are all (registered) brand names or trade marks of each respective holders, and Zoom Corporation is not associated or affiliated with them. All product names, explanation and images are used for only purpose of identifying the specific products that were referenced during product development.