Professional Documents
Culture Documents
Installation Guide
Typical iVIZION-xx-SS
(Not Included)
JCM is a registered trademark of JCM American Corporation. All other product names
mentioned herein may be registered trademarks or trademarks of their respective companies.
Furthermore, , and are not always mentioned in each case throughout this publication.
Connection
Required for
Download
Typical UBA/iVIZION JCM Tool Suite Installation Equipment & Cable Requirements
For the Americas & Oceania, E-mail: support@jcmglobal.com
For the UK, Ireland, Europe, Africa, Russia & Middle East, E-mail: support@jcmglobal.eu Figure 1 Typical JCM Tool Suite Hardware Component Interconnections
For Asia E-mail: asiapactechsupport@jcmglobal.com
Part No. 960-100923R_ Rev. 2 24 2012, JCM Global, Corporation Part No. 960-100923R_ Rev. 2 1 2012, JCM Global, Corporation
JCM Tool Suite Software Installation Guide Installation Guide March, 2012
The "JCM Tool Suite Standard Edition" Application also allows AccLoad
information to be accessed on a UBA using only the front USB Port of the
UBA Unit. The "JCM Tool Suite Standard Edition" also works with the
iVIZION Units containing current released versions of the iVIZION Soft-
ware.
The JCM Tool Suite Standard Edition Application is Windows XP, Vista
and Windows 7 compatible, and is available for download at the JCM Website
(http://www.jcmglobal.com/en/support/downloads/tools.aspx).
INSTALLING RELATED DEVICE DRIVERS UBA BARCODE TICKET/COUPON REJECT ERROR CODES
NOTE: The JCM Device Drivers will only need to be installed if a UBA Application was not Table 4 lists the UBA and Barcode Ticket/Coupon Reject Error Codes
previously installed on the PC. mentioned on Sheet 4 of the AccLoad Application Program.
The UBA/iVIZION USB Device Drivers need to be installed when using the Table 4 UBA Barcode Ticket/Coupon Reject Error Codes
JCM Tool Suite Application.
To install the necessary Drivers, follow these steps: Error No. Error Description Possible Cause
1. Connect power to the UBA or iVIZION Unit. Barcode Function not
1 Acceptance of ticket is disabled
2. Attach a Male A to Male B Type USB Cable between an open Port on the PC set
and the UBA or attach a Male A to Mini-B Type USB Cable iVIZION 2 Format Unknown Incorrect Barcode format
Unit. 3 Character Length Improper character length
3. When communication is established, a "Found New Hardware Wizard prompt 4 Start Character Could not find the start character
will appear (See Figure 2). 5 Stop Character Could not find the stop character
6 Barcode Type error Barcode format error
7 Reserved N/A
8 Ticket Transparency Double Tickets detected
9 Reserved N/A
10 Photo Level Barcode too light
11 Upside down Ticket Index mark on the wrong side
12 Reserved N/A
13 Ticket Length Ticket length is too long or too short
a 14 Reserved N/A
15 Reserved N/A
c b NOTE: iVIZION Error Codes are listed in the iVIZION Operations and Maintenance Manual
(JAC Part No. 960-100929R). Retrieve this Service Manual from the JCM Global Website at:
http://www.jcmglobal.com/en/support/downloads/Manuals.aspx
The Figure 4 example shown is for a UBA Unit; a similar display will appear when UBA ERROR CODES REJECT NOTE ERRORS (CONTINUED)
connecting an iVIZION Unit. Table 2 lists the UBA Reject Note Error Codes mentioned on Sheet 2 of the
AccLoad Application Program.
Table 2 UBA Reject Note Error Codes
ACCLOAD ERROR CODE TABLES JCM TOOL SUITE FUNCTIONS - UBA OR IVIZION
UBA ERROR CODES REJECT ERRORS FUNCTIONS AVAILABLE
Table 1 lists the UBA Reject Data Error Codes mentioned on Sheet 4 of the The available Functions for the UBA Unit (Review Figure 4) using the JCM
AccLoad Application Program. Tool Suite include the following three types:
NOTE: To define a specific UBA Data Error Code, refer to the UBA Operations and Service Download
Manual on the JCM Global Website at: http://www.jcmglobal.com/en/support/downloads/ Statistics
Manuals.aspx. Sensor Adjustment.
Table 1 UBA Reject Data Error Codes When an iVIZION Unit (See Figure 5) is connected, the following functions
are available in the Operations Mode:
Error No. Error Description Possible Cause
Download
1 Slant Insertion Entrance Sensor, Validation Sensors Statistics
Magnetic Sensor Pattern Utility.
2 Clean Magnetic Head and Roller
Error If the iVIZION Unit is connected to the JCM Tool Suite while in Maintenance
3 Idle Detection
Check for jammed Banknote, clean Opti- Mode, the following additional functions will be available as well:
cal Sensors Lens Sensor Adjustment
Clean Upper or Lower Sensors Lens, Performance Test.
4 Sensor Adjustment Calibrate if error continues
Clean Belts and/or debris blocking the
5 Banknote Feed Error
Banknotes path
Banknote Identification Check Banknote Condition, clean
a
6
Error Sensors Lens
7 Bar Code Error Clean Barcode Readers Lens
Double Banknote inserted, clean Valida-
8 Double Detect
tion Sensors Lens
Banknote Disabled by Command or DIP
9 Inhibit Banknote
Switch setting
Return by Host
10 Banknote Returned by Host Command
Command
11 Reserved N/A
Banknote Detection Check all Banknote path Sensors,
12
Error clean the Sensor Lenses
Banknote Length Error Check
Banknote condition, clean Validat-
13
ing Sensors lens
Check for dirty/clouded Lenses; clean
14 Photo Pattern Error the Lenses, Upper and/or Lower Sensor b
Circuit Board failure.
d
Clean the UV Sensor and White Reflec-
15 UV Optical Sensor Error tive Block.
c e
Figure 5 iVIZION Unit Connected JCM Tool Suite Program Screen
b
a
c
a c
b
a
b
a
c
Figure 12 iVIZION Utility Tool Suite CIS Image Program Screen
The image information can then be read from the iVIZION, saved to a File or Figure 7 UBA Statistics AccLoad Program Screen
read from a File previously saved. To read the AccLoad Data from the UBA Memory, Mouse-click on the large
The UP CIS IMAGE Screen area (See Figure 12 a) shows the UP Side Sur- Read Screen Button (See Figure 7 a).
face of the Banknote as inserted, and the DOWN CIS IMAGE Screen area (See Further Information on using all of the Tabs and Fields on the Accload Pro-
Figure 12 b) shows the Down Side Surface of the Banknote as inserted. gram refer to the ACCLOAD Software Installation Guide, (Part No. 960-
The Read , File Save and File Read Screen Buttons 100918R_ Rev. A) available on the JCM Global Website.
(See Figure 12 c) collectively provide the ability to retrieve or save an image to
a File Folder.
d
a
f g
b
e c
d
a
Figure 8 iVIZION AccLoad Program Statistics Screen Figure 11 iVIZION Utility Tool Suite Program Primary Screen
To read the Accload information from an iVIZION Unit, Mouse-click on the
large "Read" Screen Button (See Figure 8 a).
d 2. Apply power to the iVIZION Unit. The Status Indicator on the front right side
c of the Unit will light Blue to indicate the iVIZION Unit is in Diagnostic Mode.
3. Enter the Performance Test Mode, by selecting "Performance Test" (Review Fig-
ure 5 e) using the Down Arrow to the right of the Service Mode Pull-Down
a Menu on the Screen (Review Figure 5 b), select "Performance Test" from the
b
Menu and the Figure 10 Screen will appear.