Professional Documents
Culture Documents
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 2 of 57
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 3 of 57
AMR Configuration ID
Support AMR Codec
Use cell AMR parameter
AMR full Active Codec Set(4.75kbps)
AMR full Active Codec Set(5.15kbps)
AMR full Active Codec Set(5.9kbps)
AMR full Active Codec Set(6.7kbps)
AMR full Active Codec Set(7.4kbps)
AMR full Active Codec Set(7.95kbps)
AMR full Active Codec Set(10.2kbps)
AMR full Active Codec Set(12.2kbps)
AMR Half Active Codec Set(4.75kbps)
AMR Half Active Codec Set(5.15kbps)
AMR Half Active Codec Set(5.9kbps)
AMR Half Active Codec Set(6.7kbps)
AMR Half Active Codec Set(7.4kbps)
AMR Half Active Codec Set(7.95kbps)
Thresholds of AMR FR 1
Thresholds of AMR FR 2
Thresholds of AMR FR 3
Thresholds of AMR FR 4
Thresholds of AMR FR 5
Thresholds of AMR FR 6
Thresholds of AMR FR 7
Thresholds of AMR HR 1
Thresholds of AMR HR 2
Thresholds of AMR HR 3
Thresholds of AMR HR 4
Thresholds of AMR HR 5
Hysteresis of AMR FR 1
Hysteresis of AMR FR 2
Hysteresis of AMR FR 3
Hysteresis of AMR FR 4
Hysteresis of AMR FR 5
Hysteresis of AMR FR 6
Hysteresis of AMR FR 7
Hysteresis of AMR HR 1
Hysteresis of AMR HR 2
Hysteresis of AMR HR 3
Hysteresis of AMR HR 4
Hysteresis of AMR HR 5
Enable AMR FR noise control
AMR FR Initial codec mode
AMR FR Start mode
Enable AMR HR noise control
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 4 of 57
MAX value of MS Radio link
MAX value of MS Radio link
MAX value of MS Radio link
AMR Configuration ID
Abbreviation GCellAmr
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 5 of 57
Instance None
Unit N/A
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrSupport
Instance Cell
0: Not Support
Value Range and Step 1: Support
Unit N/A
Default Value 1
Default Value Configuration Reason The AMR function is restricted by LICENSE, so the default setting is Not Supported.
Configuration Rule and Adjustment Suggestion Configure this parameter in accordance with the LICENSE.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 6 of 57
Abbreviation useCellAmrParam
This parameter indicates whether the AMR parameters of the cell are enabled.
If no, the AMR parameters set in the BSC are preferred.
Description If yes, the AMR parameters of the cell are preferred.
Instance Cell
0: No
Value Range and Step 1: Yes
Unit N/A
Default Value 0
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs1
Description This parameter specifies whether the ACS of AMR FR contains the 4.75kbps codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 7 of 57
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs2
Description This parameter specifies whether the ACS of AMR FR contains the 5.15 kbps codec mode.
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs3
Description This parameter specifies whether the ACS of AMR FR contains the 5.9 kbps codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 8 of 57
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs4
Description This parameter specifies whether the ACS of AMR FR contains the 6.7 kbps codec mode.
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs5
Description This parameter specifies whether the ACS of AMR FR contains the 7.4 kbps codec mode.
Instance Cell
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 9 of 57
Unit N/A
Default Value 1
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs6
Description This parameter specifies whether the ACS of AMR FR contains the 7.95 kbps codec mode.
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs7
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 10 of 57
Description This parameter specifies whether the ACS of AMR FR contains the 10.2 kbps codec mode.
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFullAcs8
Description This parameter specifies whether the ACS of AMR FR contains the 12.2 kbps codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Use both high rate and low rate.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 11 of 57
Abbreviation amrHalfAcs1
Description This parameter specifies whether the ACS of AMR HR contains the 4.75 kbps codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Using both high rate and low rate is widely applicable.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHalfAcs2
Description This parameter specifies whether the ACS of AMR HR contains the 5.15 kbps codec mode.
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Using both high rate and low rate is widely applicable.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 12 of 57
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHalfAcs3
Description This parameter specifies whether the ACS of AMR HR contains the 5.9 kbps codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Using both high rate and low rate is widely applicable.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHalfAcs4
Description This parameter specifies whether the ACS of AMR HR contains the 6.7 kbps codec mode.
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Using both high rate and low rate is widely applicable.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 13 of 57
Configuration Rule and Adjustment Suggestion Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHalfAcs5
Description This parameter specifies whether the ACS of AMR HR contains the 7.4 kbps codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Using both high rate and low rate is widely applicable.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHalfAcs6
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 14 of 57
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Using both high rate and low rate is widely applicable.
Generally, select both high rate and low rate. When the radio signals in a cell are comparatively good, select high rate
Configuration Rule and Adjustment Suggestion
only. When the radio signals in a cell are comparatively bad, select low rate only.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR FR 1
Abbreviation amrFrThresholds1
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 4.75kbps.
Instance Cell
Unit N/A
Default Value 13
Relationship N/A
Impact on Equipment 0
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 15 of 57
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR FR 2
Abbreviation amrFrThresholds2
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 5.15 kbps.
Instance Cell
Unit N/A
Default Value 14
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR FR 3
Abbreviation amrFrThresholds3
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 16 of 57
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 5.9kbps.
Instance Cell
Unit N/A
Default Value 15
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR FR 4
Abbreviation amrFrThresholds4
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 6.7kbps.
Instance Cell
Unit N/A
Default Value 17
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 17 of 57
amrFrThresholds6
amrFrThresholds7
amrFrHysteresis1
amrFrHysteresis2
amrFrHysteresis3
amrFrHysteresis4
amrFrHysteresis5
amrFrHysteresis6
amrFrHysteresis7
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR FR 5
Abbreviation amrFrThresholds5
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 7.4kbps.
Instance Cell
Unit N/A
Default Value 18
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 18 of 57
Thresholds of AMR FR 6
Abbreviation amrFrThresholds6
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 7.95kbps.
Instance Cell
Unit N/A
Default Value 20
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR FR 7
Abbreviation amrFrThresholds7
Description This parameter specifies the C/I threshold for reducing the AMR FR codec mode to 10.2kbps.
Instance Cell
Unit N/A
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 19 of 57
Default Value 23
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR HR 1
Abbreviation amrHrThresholds1
Description This parameter specifies the C/I threshold for reducing the AMR HR codec mode to 4.75kbps.
Instance Cell
Unit N/A
Default Value 18
Default Value Configuration Reason The CIR when different AMR rates are at 1% FER, which is obtained by system simulation
Relationship N/A
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 20 of 57
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR HR 2
Abbreviation amrHrThresholds2
Description This parameter specifies the C/I threshold for reducing the AMR HR codec mode to 5.15kbps.
Instance Cell
Unit N/A
Default Value 20
Default Value Configuration Reason The CIR when different AMR rates are at 1% FER, which is obtained by system simulation
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR HR 3
Abbreviation amrHrThresholds3
Description This parameter specifies the C/I threshold for reducing the AMR HR codec mode to 5.9kbps.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 21 of 57
Instance Cell
Unit N/A
Default Value 23
Default Value Configuration Reason The CIR when different AMR rates are at 1% FER, which is obtained by system simulation
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR HR 4
Abbreviation amrHrThresholds4
Description This parameter specifies the C/I threshold for reducing the AMR HR codec mode to 6.7kbps.
Instance Cell
Unit N/A
Default Value 26
Default Value Configuration Reason The CIR when different AMR rates are at 1% FER, which is obtained by system simulation
Relationship N/A
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 22 of 57
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Thresholds of AMR HR 5
Abbreviation amrHrThresholds5
Description This parameter specifies the C/I threshold for reducing the AMR HR codec mode to 7.4kbps.
Instance Cell
Unit N/A
Default Value 30
Default Value Configuration Reason The CIR when different AMR rates are at 1% FER, which is obtained by system simulation
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 1
Abbreviation amrFrHysteresis1
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 4.75kbps.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 23 of 57
Instance Cell
Unit N/A
Default Value 3
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 2
Abbreviation amrFrHysteresis2
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 5.15kbps.
Instance Cell
Unit N/A
Default Value 3
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 24 of 57
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 3
Abbreviation amrFrHysteresis3
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 5.9kbps.
Instance Cell
Unit N/A
Default Value 3
Relationship N/A
Impact on Equipment 0
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 25 of 57
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 4
Abbreviation amrFrHysteresis4
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 6.7kbps.
Instance Cell
Unit N/A
Default Value 3
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 5
Abbreviation amrFrHysteresis5
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 26 of 57
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 7.4kbps.
Instance Cell
Unit N/A
Default Value 3
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 6
Abbreviation amrFrHysteresis6
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 7.95kbps.
Instance Cell
Unit N/A
Default Value 4
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 27 of 57
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR FR 7
Abbreviation amrFrHysteresis7
Description This parameter specifies C/I hysteresis for increasing the AMR HR codec mode from 10.2kbps.
Instance Cell
Unit N/A
Default Value 4
Relationship N/A
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 28 of 57
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR HR 1
Abbreviation amrHrHysteresis1
Description This parameter specifies C/I hysteresis for increasing the AMR FR codec mode from 4.75kbps.
Instance Cell
Unit N/A
Default Value 3
Determine whether the Hysteresis parameter value is appropriate by observing the frequency of rate adjustment (for
Configuration Rule and Adjustment Suggestion example, through test analysis or by using the AMR rate monitoring tool). When rate adjustment is frequently
performed, set this parameter to a larger value.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR HR 2
Abbreviation amrHrHysteresis2
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 29 of 57
Description This parameter specifies C/I hysteresis for increasing the AMR FR codec mode from 5.15kbps.
Instance Cell
Unit N/A
Default Value 3
Determine whether the Hysteresis parameter value is appropriate by observing the frequency of rate adjustment (for
Configuration Rule and Adjustment Suggestion example, through test analysis or by using the AMR rate monitoring tool). When rate adjustment is frequently
performed, set this parameter to a larger value.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR HR 3
Abbreviation amrHrHysteresis3
Description This parameter specifies C/I hysteresis for increasing the AMR FR codec mode from 5.9kbps.
Instance Cell
Unit N/A
Default Value 3
Determine whether the Hysteresis parameter value is appropriate by observing the frequency of rate adjustment (for
Configuration Rule and Adjustment Suggestion example, through test analysis or by using the AMR rate monitoring tool). When rate adjustment is frequently
performed, set this parameter to a larger value.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 30 of 57
amrHrThresholds5
amrHrHysteresis1
amrHrHysteresis2
amrHrHysteresis4
amrHrHysteresis5
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR HR 4
Abbreviation amrHrHysteresis4
Description This parameter specifies C/I hysteresis for increasing the AMR FR codec mode from 6.7kbps.
Instance Cell
Unit N/A
Default Value 4
Determine whether the Hysteresis parameter value is appropriate by observing the frequency of rate adjustment (for
Configuration Rule and Adjustment Suggestion example, through test analysis or by using the AMR rate monitoring tool). When rate adjustment is frequently
performed, set this parameter to a larger value.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMR HR 5
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 31 of 57
Abbreviation amrHrHysteresis5
Description This parameter specifies C/I hysteresis for increasing the AMR FR codec mode from 7.4kbps.
Instance Cell
Unit N/A
Default Value 4
Determine whether the Hysteresis parameter value is appropriate by observing the frequency of rate adjustment (for
Configuration Rule and Adjustment Suggestion example, through test analysis or by using the AMR rate monitoring tool). When rate adjustment is frequently
performed, set this parameter to a larger value.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFrNscb
This parameter specifies whether the AMR noise suppression on the MS is disabled for the AMRFR speech version.
The noise suppression function on the MS keeps the speech quality by controlling the background noise.
No: Noise control can be enabled.
Description Yes: Noise control is disabled.
Instance Cell
0: No
Value Range and Step 1: Yes
Unit N/A
Default Value 0
Default Value Configuration Reason Enabling noise suppression can eliminate noise and improve voice quality.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 32 of 57
Generally, enable the noise suppression function. When speech voice is degraded, pay attention to the parameter
setting.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrFrIcm
This parameter indicates the initial speech codec mode of AMR FR employs the mode specified by Startmode or the
default initial codec mode specified in protocol 45.009. The initial codec mode specified in the protocol is described as
follows:
1. When there is one codec mode, this mode is employed as the initial mode.
2. When there are two or three codec modes, the lowest speed mode is employed as the initial mode.
3. When there are four modes, the mode with the second lowest speed is employed as the initial mode.
For the A interface using IP, this parameter is not used. Instead, the system control parameter IpaAMRStartMode
Description decides the initial codec mode.
Instance Cell
0: No
Value Range and Step 1: Yes
Unit N/A
Default Value 1
Default Value Configuration Reason Set the initial codec mode as required
If initial rate needs no special consideration, set this parameter to "Start Coding Mode", meaning the default initial rate
Configuration Rule and Adjustment Suggestion
specified in the protocol.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 33 of 57
Abbreviation amrFrStartMode
This parameter decides the initial codec mode for the AMR FR speech version. The value must not be larger than the
number of codec modes contained in the ACS. The parameter values are described as follows:
1: the initial codec mode employs the one with the lowest speed
2: the initial codec mode employs the one with the second lowest speed
3: the initial codec mode employs the one with the third lowest speed
Description 4: the initial codec mode employs the one with the forth lowest speed
Instance Cell
Unit N/A
Default Value 4
Using the lowest coding mode can ensure that comparatively good voice quality can be provided in bad radio
Default Value Configuration Reason
condition.
Configuration Rule and Adjustment Suggestion If the radio quality is good, use a higher initial rate.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHrNscb
This parameter specifies whether the AMR noise suppression on the MS is disabled for the AMRHR speech version.
The noise suppression function on the MS keeps the speech quality by controlling the background noise.
No: Noise control can be enabled.
Description Yes: Noise control is disabled.
Instance Cell
0: No
Value Range and Step 1: Yes
Unit N/A
Default Value 0
Default Value Configuration Reason Enabling noise suppression can eliminate noise and improve voice quality.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 34 of 57
Configuration Rule and Adjustment Suggestion Generally, enable the noise suppression function. When speech voice is degraded, pay attention to the parameter
setting.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrHrIcm
This parameter indicates the initial speech codec mode of AMR HR employs the mode specified by Startmode or the
default initial codec mode specified in protocol 45.009. The initial codec mode specified in the protocol is described as
follows:
1. When there is one codec mode, this mode is employed as the initial mode.
2. When there are two or three codec modes, the lowest speed mode is employed as the initial mode.
3. When there are four modes, the mode with the second lowest speed is employed as the initial mode.
For the A interface using IP, this parameter is not used. Instead, the system control parameter IpaAMRStartMode
Description decides the initial codec mode.
Instance Cell
Unit N/A
Default Value 1
Default Value Configuration Reason Set the initial codec mode as required
If initial rate needs no special consideration, set this parameter to "Start Coding Mode", meaning the default initial rate
Configuration Rule and Adjustment Suggestion
specified in the protocol.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 35 of 57
Abbreviation amrHrStartMode
This parameter decides the initial codec mode for the AMR HR speech version. The value must not be larger than the
number of codec modes contained in the ACS. The parameter values are described as follows:
1: the initial codec mode employs the one with the lowest speed
2: the initial codec mode employs the one with the second lowest speed
3: the initial codec mode employs the one with the third lowest speed
Description 4: the initial codec mode employs the one with the forth lowest speed
Instance Cell
Unit N/A
Default Value 3
Using the lowest coding mode can ensure that comparatively good voice quality can be provided in bad radio
Default Value Configuration Reason
condition.
Configuration Rule and Adjustment Suggestion If the radio quality is good, use a higher initial rate to improve the voice quality.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrAdjMode
The AMR rate regulation mode falls into two types: AMR quick regulation where the BTS perform self-control, and
Description quick regulation mode where the BTS use the default time (960ms).
Instance Cell
Unit N/A
Default Value 0
Default Value Configuration Reason Due to the practical application of the net
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 36 of 57
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrAdjInterval
This parameter specifies the interval for AMR codec adjustment. This parameter is valid when the AmrAdjMode
Description parameter is set to "Interval-based adjustment mode". Refer to the description of AmrAdjMode for more information.
Instance Cell
Unit 480ms
Default Value 1
Default Value Configuration Reason Due to the practical application of the net
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Full Name BSS radio link timer's max value for AMR FR
Abbreviation bsRadioLkTmOutAMRFR
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 37 of 57
This parameter indicates the maximum value (initial value) of S that is the counter for AMR-FRvoice service failure.
GSM rule specifies that BTS needs a counter S, which is rendered a value recorded in parameter BsRadioLkTmout
when the call starts. Once BTS fails to decode a correct SACCH message when it should, S will decrease by 1. Once
BTS decodes a correct SACCH message, S is increased by 2. The value of S cannot exceed BsRadioLkTmout.
Description When S reaches 0, BTS will report radio link fault. This counter is designed for AMR-FR voice service.
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit SACCH mf
Default Value 15
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Full Name BSS radio link timer's max value for AMR HR
Abbreviation bsRadioLkTmOutAMRHR
This parameter indicates the maximum value (initial value) of S that is the counter for AMR-HRvoice service failure.
GSM rule specifies that BTS needs a counter S, which is rendered a value recorded in parameter BsRadioLkTmout
when the call starts. Once BTS fails to decode a correct SACCH message when it should, S will decrease by 1. Once
BTS decodes a correct SACCH message, S is increased by 2. The value of S cannot exceed BsRadioLkTmout.
Description When S reaches 0, BTS will report radio link fault. This counter is designed for AMR-HR voice service.
Instance Cell
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 38 of 57
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
15: 64
Unit SACCH mf
Default Value 15
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation msRadioLkTmOutAMRFR
This parameter indicates the maximum value of the MS-side radio link counter S that is used for AMR FR. The
parameter value is transmitted on the BCCH or SACCH by the BSS.
The radio link counter S is used to evaluate radio link failures.
S is decreased by one when the MS fails to decode an SACCH message (BFI=1).
S is increased by two when the MS receives an SACCH message (BFI=0).
Description When S=0, which indicates a radio link failure, the call is reestablished or released.
Instance Cell
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 39 of 57
12: 52
13: 56
14: 60
15: 64
Unit N/A
Default Value 15
Default Value Configuration Reason MS calls to increase error tolerance for the wireless link
Relationship N/A
Related Interfaces Um
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation msRadioLkTmOutAMRHR
This parameter indicates the maximum value of the MS-side radio link counter S that is used for AMR HR. The
parameter value is transmitted on the BCCH or SACCH by the BSS.
The radio link counter S is used to evaluate radio link failures.
S is decreased by one when the MS fails to decode an SACCH message (BFI=1).
S is increased by two when the MS receives an SACCH message (BFI=0).
Description When S=0, which indicates a radio link failure, the call is reestablished or released.
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit N/A
Default Value 15
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 40 of 57
Default Value Configuration Reason MS calls to increase error tolerance for the wireless link
Relationship N/A
Related Interfaces Um
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation SUPPORTAMRWB
Description This parameter indicates whether the AMR-WB is supported in a cell. It is configured for individual cells.
Instance Cell
0: Not Support
Value Range and Step 1: Support
Unit N/A
Default Value 0
Default Value Configuration Reason the parameter is a feature switch, default value is No.
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMRWFS 1
Abbreviation amrWfsHysteresis1
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 41 of 57
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
Description amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 3
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
Relationship The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMRWFS 2
Abbreviation amrWfsHysteresis2
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
Description amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 3
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 42 of 57
Configuration Rule and Adjustment you can decide whether this parameter is set properly. When the rate
Suggestion is adjusted too frequently, you can set the parameter to a higher
value.
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
Relationship The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMRWFS 3
Abbreviation amrWfsHysteresis3
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
Description amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 3
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
Relationship The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 43 of 57
Hysteresis of AMRWFS 4
Abbreviation amrWfsHysteresis4
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
Description amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 3
The hysteresis for changing AMRWFS mode includes four factors, which are represented by four parameters:
amrWfsHysteresis1, amrWfsHysteresis2, amrWfsHysteresis3, and amrWfsHysteresis4.
Relationship The four parameter values must meet the following condition:
amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMROWFS 1
Abbreviation amrOwfsHysteresis1
The hysteresis for changing AMROWFS mode includes two factors, which are represented by two parameters:
amrOwfsHysteresis1 and amrOwfsHysteresis2.
The two parameter values must meet the following condition:
Description amrOwfsThresholds1 amrOwfsHysteresis1amrOwfsThresholds2 amrOwfsHysteresis2
Instance Cell
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 44 of 57
Unit N/A
Default Value 3
The hysteresis for changing AMROWFS mode includes two factors, which are represented by two parameters:
amrOwfsHysteresis1 and amrOwfsHysteresis2.
Relationship
The two parameter values must meet the following condition:
amrOwfsThresholds1 amrOwfsHysteresis1amrOwfsThresholds2 amrOwfsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMROWFS 2
Abbreviation amrOwfsHysteresis2
The hysteresis for changing AMROWFS mode includes two factors, which are represented by two parameters:
amrOwfsHysteresis1 and amrOwfsHysteresis2.
The two parameter values must meet the following condition:
Description amrOwfsThresholds1 amrOwfsHysteresis1amrOwfsThresholds2 amrOwfsHysteresis2
Instance Cell
Unit N/A
Default Value 3
The hysteresis for changing AMROWFS mode includes two factors, which are represented by two parameters:
amrOwfsHysteresis1 and amrOwfsHysteresis2.
Relationship
The two parameter values must meet the following condition:
amrOwfsThresholds1 amrOwfsHysteresis1amrOwfsThresholds2 amrOwfsHysteresis2
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 45 of 57
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMROWHS 1
Abbreviation amrOwhsHysteresis1
The hysteresis for changing AMROWHS mode includes two factors, which are represented by two parameters:
amrOwhsHysteresis1 and amrOwhsHysteresis2.
The two parameter values must meet the following condition:
Description amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Instance Cell
Unit N/A
Default Value 3
The hysteresis for changing AMROWHS mode includes two factors, which are represented by two parameters:
amrOwhsHysteresis1 and amrOwhsHysteresis2.
Relationship
The two parameter values must meet the following condition:
amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Hysteresis of AMROWHS 2
Abbreviation amrOwhsHysteresis2
Description The hysteresis for changing AMROWHS mode includes two factors, which are represented by two parameters:
amrOwhsHysteresis1 and amrOwhsHysteresis2.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 46 of 57
Instance Cell
Unit N/A
Default Value 3
The hysteresis for changing AMROWHS mode includes two factors, which are represented by two parameters:
amrOwhsHysteresis1 and amrOwhsHysteresis2.
Relationship
The two parameter values must meet the following condition:
amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrWfsThresholds1
There are four threshold values during AMRWFS mode change: amrWfsThresholds1, amrWfsThresholds2, amrWfsThresholds3, and
amrWfsThresholds4. The following condition must be met:
amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4 amrWfsThresholds1
amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3 amrWfsHysteresis3amrWfsThresholds4
Description amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Generally, you do not have to adjust the setting
Adjustment Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
Relationship There are four thresholds for changing AMRWFS mode, which are represented by four parameters: amrWfsThresholds1,
amrWfsThresholds2, amrWfsThresholds3, and amrWfsThresholds4.
The four parameter values must meet the following two conditions:
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 47 of 57
(1) amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4
(2) amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrWfsThresholds2
There are four threshold values during AMRWFS mode change: amrWfsThresholds1, amrWfsThresholds2, amrWfsThresholds3,
amrWfsThresholds4. The following condition must be met:
amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4 amrWfsThresholds1
amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3 amrWfsHysteresis3amrWfsThresholds4
Description amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Generally, you do not have to adjust the setting
Adjustment Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
There are four thresholds for changing AMRWFS mode, which are represented by four parameters: amrWfsThresholds1,
amrWfsThresholds2, amrWfsThresholds3, and amrWfsThresholds4.
The four parameter values must meet the following two conditions:
Relationship
(1) amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4
(2) amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrWfsThresholds3
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 48 of 57
There are four threshold values during AMRWFS mode change: amrWfsThresholds1, amrWfsThresholds2, amrWfsThresholds3,
amrWfsThresholds4. The following condition must be met:
amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4 amrWfsThresholds1
amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3 amrWfsHysteresis3amrWfsThresholds4
Description amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Generally, you do not have to adjust the setting
Adjustment Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
There are four thresholds for changing AMRWFS mode, which are represented by four parameters: amrWfsThresholds1,
amrWfsThresholds2, amrWfsThresholds3, and amrWfsThresholds4.
The four parameter values must meet the following two conditions:
Relationship
(1) amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4
(2) amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrWfsThresholds4
There are four threshold values during AMRWFS mode change: amrWfsThresholds1, amrWfsThresholds2, amrWfsThresholds3,
amrWfsThresholds4. The following condition must be met:
amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4 amrWfsThresholds1
amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3 amrWfsHysteresis3amrWfsThresholds4
Description amrWfsHysteresis4
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Generally, you do not have to adjust the setting
Adjustment Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 49 of 57
There are four thresholds for changing AMRWFS mode, which are represented by four parameters: amrWfsThresholds1,
amrWfsThresholds2, amrWfsThresholds3, and amrWfsThresholds4.
The four parameter values must meet the following two conditions:
Relationship
(1) amrWfsThresholds1amrWfsThresholds2amrWfsThresholds3amrWfsThresholds4
(2) amrWfsThresholds1 amrWfsHysteresis1amrWfsThresholds2 amrWfsHysteresis2amrWfsThresholds3
amrWfsHysteresis3amrWfsThresholds4 amrWfsHysteresis4
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrOwfsThresholds1
There are two thresholds for changing AMROWFS mode, which are represented by two parameters: amrOwfsThresholds1
and amrOwfsThresholds2.
The two parameter values must meet the following two conditions:
(1) amrOwfsThresholds1amrOwfsThresholds2
Description (2) amrOwfsThresholds1 amrOwfsHysteresis1 amrOwfsThresholds2 amrOwfsHysteresis2
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Adjustment Generally, you do not have to adjust the setting
Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
There are two thresholds for changing AMROWFS mode, which are represented by two parameters: amrOwfsThresholds1
and amrOwfsThresholds2.
Relationship The two parameter values must meet the following two conditions:
(1) amrOwfsThresholds1amrOwfsThresholds2
(2) amrOwfsThresholds1 amrOwfsHysteresis1 amrOwfsThresholds2 amrOwfsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 50 of 57
Abbreviation amrOwfsThresholds2
There are two thresholds for changing AMROWFS mode, which are represented by two parameters: amrOwfsThresholds1
and amrOwfsThresholds2.
The two parameter values must meet the following two conditions:
(1) amrOwfsThresholds1amrOwfsThresholds2
Description (2) amrOwfsThresholds1 amrOwfsHysteresis1 amrOwfsThresholds2 amrOwfsHysteresis2
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Adjustment Generally, you do not have to adjust the setting
Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
There are two thresholds for changing AMROWFS mode, which are represented by two parameters: amrOwfsThresholds1
and amrOwfsThresholds2.
Relationship The two parameter values must meet the following two conditions:
(1) amrOwfsThresholds1amrOwfsThresholds2
(2) amrOwfsThresholds1 amrOwfsHysteresis1 amrOwfsThresholds2 amrOwfsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrOwhsThresholds1
There are two thresholds for changing AMROWHS mode, which are represented by two parameters: amrOwhsThresholds1
and amrOwhsThresholds2.
The two parameter values must meet the following two conditions:
(1) amrOwhsThresholds1amrOwhsThresholds2
Description (2) amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Adjustment Generally, you do not have to adjust the setting
Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 51 of 57
There are two thresholds for changing AMROWHS mode, which are represented by two parameters: amrOwhsThresholds1
and amrOwhsThresholds2.
Relationship The two parameter values must meet the following two conditions:
(1) amrOwhsThresholds1amrOwhsThresholds2
(2) amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation amrOwhsThresholds2
There are two thresholds for changing AMROWHS mode, which are represented by two parameters: amrOwhsThresholds1
and amrOwhsThresholds2.
The two parameter values must meet the following two conditions:
(1) amrOwhsThresholds1amrOwhsThresholds2
Description (2) amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Instance Cell
Unit N/A
Default Value 6
Configuration Rule and Adjustment Generally, you do not have to adjust the setting
Suggestion of this parameter unless the FER measured by the BTS exceeds 1%.
There are two thresholds for changing AMROWHS mode, which are represented by two parameters: amrOwhsThresholds1
and amrOwhsThresholds2.
Relationship The two parameter values must meet the following two conditions:
(1) amrOwhsThresholds1amrOwhsThresholds2
(2) amrOwhsThresholds1 amrOwhsHysteresis1amrOwhsThresholds2 amrOwhsHysteresis2
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 52 of 57
Abbreviation msRadioLkOutAmrWfs
This parameter indicates the maximum value of the MS-side radio link counter S used for AMR WFS. The parameter
value is transmitted on the BCCH or SACCH by the BSS.
The radio link counter S is used to evaluate radio link failures.
S is decreased by one when the MS fails to decode an SACCH message (BFI=1).
S is increased by two when the MS receives an SACCH message (BFI=0).
Description When S=0, which indicates a radio link failure, the call is reestablished or released.
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit N/A
Default Value 15
Default Value Configuration Reason MS calls to increase error tolerance for the wireless link
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation msRadioLkOutAmrOwfs
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 53 of 57
This parameter indicates the maximum value of the MS-side radio link counter S that is used for AMR-WB OWFS. The
parameter value is transmitted on the BCCH or SACCH by the BSS.
The radio link counter S is used to evaluate radio link failures.
S is decreased by one when the MS fails to decode an SACCH message (BFI=1).
S is increased by two when the MS receives an SACCH message (BFI=0).
Description When S=0, which indicates a radio link failure, the call is reestablished or released.
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit N/A
Default Value 15
Default Value Configuration Reason MS calls to increase error tolerance for the wireless link
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Abbreviation msRadioLkOutAmrOwhr
This parameter indicates the maximum value of the MS-side radio link counter S that is used for AMR-WB OWHS. The
parameter value is transmitted on the BCCH or SACCH by the BSS.
The radio link counter S is used to evaluate radio link failures.
S is decreased by one when the MS fails to decode an SACCH message (BFI=1).
S is increased by two when the MS receives an SACCH message (BFI=0).
Description When S=0, which indicates a radio link failure, the call is reestablished or released.
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 54 of 57
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit N/A
Default Value 15
Default Value Configuration Reason MS calls to increase error tolerance for the wireless link
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Full Name BSS radio link timer's max value for FR-AMR-WB
Abbreviation bsRadioLkOutAMRWFS
This parameter indicates the maximum value (initial value) of the BSS-side radio link counter S that is used for failure
detection in the case of FR-AMR-WB voice traffic. As specified in GSM protocols, the counter S is required in the BTS.
This counter is assigned an initial value (the value of BsRadioLkTmout) before a call starts. When the BTS fails to
decode a received SACCH message correctly, S is decreased by one. When the BTS receives a SACCH message
correctly, S is increased by two. The S value must be less than the BsRadioLkTmout value. When S=0, the BTS reports
Description a radio link failure.
Instance Cell
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 55 of 57
10: 44
11: 48
12: 52
13: 56
14: 60
15: 64
Unit N/A
Default Value 15
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Full Name BSS radio link timer's max value for OFR-AMR-WB
Abbreviation bsRadioLkOutAmrOwfs
This parameter indicates the maximum value (initial value) of the BSS-side radio link counter S that is used for failure
detection in the case of OFR-AMR-WB voice traffic. As specified in GSM protocols, the counter S is required in the BTS.
This counter is assigned an initial value (the value of BsRadioLkTmout) before a call starts. When the BTS fails to
decode a received SACCH message correctly, S is decreased by one. When the BTS receives a SACCH message
correctly, S is increased by two. The S value must be less than the BsRadioLkTmout value. When S=0, the BTS reports
Description a radio link failure.
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit N/A
Default Value 15
Default Value Configuration Reason This parameter can have a big value, so there
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 56 of 57
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
Full Name BSS radio link timer's max value for AMR OWHR
Abbreviation bsRadioLkOutAmrOwhr
This parameter indicates the maximum value (initial value) of the BSS-side radio link counter S that is used for failure
detection in the case of OHR-AMR-WB voice traffic. As specified in GSM protocols, the counter S is required in the
BTS. This counter is assigned an initial value (the value of BsRadioLkTmout) before a call starts. When the BTS fails to
decode a received SACCH message correctly, S is decreased by one. When the BTS receives a SACCH message
correctly, S is increased by two. The S value must be less than the BsRadioLkTmout value. When S=0, the BTS reports
Description a radio link failure.
Instance Cell
0: 4
1: 8
2: 12
3: 16
4: 20
5: 24
6: 28
7: 32
8: 36
9: 40
10: 44
11: 48
12: 52
13: 56
14: 60
Value Range and Step 15: 64
Unit N/A
Default Value 15
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017
AMR Configuration (GCellAmr) Page 57 of 57
Relationship N/A
Impact on Equipment 0
Impact on service 0
Negotiation With CN No
OMC Access Path GUI: Managed Element->GSM Logical Configuration->Cell Information Configuration->AMR Configuration
http://127.0.0.1:8890/document?channelid=2&record=1&resultid=1&prese... 8/29/2017