Professional Documents
Culture Documents
The series of EPM motors have a low speed, high torque capability. Converting hydraulic energy into
mechanical energy they are used where the power up to 11 kW is needed.
These units provide high output torque from relatively small packages. The motors are available in
displacement from 25,0 cm3/rev. to 623,6 cm3/rev. with speeds up to 1500 RPM.
The EPM motors are fixed displacement, gerotor type units that are known for compactness and economy.
All EPM motors have built-in check valves assuring pressure on the shaft seal never exeeds pressure levels seen in the
return line.
B B B
11 11
EPM
MOTORS
SPECIFICATION DATA
* Intermittend operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur fot max. 1% of every minute.
*** For speeds of 10 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simulateneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommended using a premium quality, anti-wear type mineral based hydrauliv oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm/s at operating temperatures..
0
5. Recommended maximum system operating temperature is 82 C..
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
13
EPM
MOTORS
SPECIFICATION DATA (continued)
* Intermittend operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur fot max. 1% of every minute.
*** For speeds of 10 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simulateneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommended using a premium quality, anti-wear type mineral based hydrauliv oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm/s at operating temperatures..
0
5. Recommended maximum system operating temperature is 82 C..
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
14
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPM 25
EPM 32
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
15
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPM 40
EPM 50
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
16
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPM 80
EPM 100
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
17
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPM 125
EPM 160
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
18
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPM 200
EPM 250
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
19
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAM
EPM 315
EPM 400
The function diagram data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
20
EPMM
EPM
Motoren
MOTORS
FUNCTION DIAGRAM
EPM 500
EPM 630
The function diagram data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
21
EPM
MOTORS
DIMENSIONS AND MOUNTING DATA
max L
Porting Mounting
Standard Mounting Flange
550,1
2x 13,35 +0,4
Side Ports
4x 13,35 +0,4
E - Rear Ports
550,1
Q - Square
550,1
C : 4xM8 - 13 mm depth
P (A, B): 2xG1/2 or 2xM22x1,5 - 20 mm depth min 15
22
EPM
MOTORS
DIMENSIONS AND MOUNTING DATA - EPMW (WHEEL MOTOR)
W - Mounting Flange
min 20
max L
P(A,B)
max 105
550,1
Prad
daN
-1
1: Drawing by n=200 min
1030,1 (Max. radial shaft load)
-1
2: Drawing by n=300 min
-1
3: Drawing by n=500 min
-1
Type L, mm L 1, mm 4: Drawing by n=800 min
Pamax=200 daN
23
EPM+EPRM
MOTORS
SHAFT VERSIONS FOR EPM AND EPRM MOTORS
C - 25, straight keyed, key A8x7x32 DIN 6885 CB - 32, straight keyed, key A10x8x45 DIN 6885
Max. Torque 34 daNm Max. Torque 77 daNm
min16
min 16
43,20,5 +0,4
56,5 -1,0
CO - 1", straight keyed, key "x"x1" BS46 SB - splined A25x22xH10 DIN 5482
Max. Torque 34 daNm Max. Torque 34 daNm
250,210
220,130
min16
43,20,5
SH - splined, BS 2059 (SAE 6B) KB - tapered 1:10, key B6x6x20 DIN 6885
Max. Torque 34 daNm Max. Torque 77 daNm
580,4
360,7
25,320,03
4,50,1
M8
min 16 Deep
350,01
min 26,4
K - tapered 1:10, key B5x5x14 DIN 6885 OB - tapered 1:8 SAEJ 501, key 5
16"x 5 16"x1" BS46
Max. Torque 40 daNm Max. Torque 77 daNm +0,4
56,5 -1,0
350,6
4,50,1 4
28,560,01
5-0,75 50,25
SA - splined, B25x22h9 DIN 5482 HB - 14T splined, 1" ANS B92.1-1976 Norm
Max. Torque 40 daNm Max. Torque 77 daNm
M8
min 16 Deep
min 16
43,20,5
D +0,4
24
EPM+EPRM
MOTORS
PERMISSIBLE SHAFT LOADS FOR EPM AND EPRM MOTORS
The permissible radial shaft load Prad depends on the speed (RPM) and distance (L) from the point of load
to the mounting flange.
Mounting Flange
Radial Shaft Load Prad for EPMN (EPRMN) Radial Shaft Load Prad for all Versions
Prad EPM and EPRM by L=30 (24) mm
daN Prad
Standard and F
Versions
Q - Version
Prad
daN
L, mm
L
1 - Drawing by n 200 min-1
Prad
2 - Drawing by n 300 min-1
3 - Drawing by n 500 min-1
4 - Drawing by n 800 min-1
bar
250
The shaft seal pressure
equals the average of
200 input presure and return
150 pressure
100 Pinp.+Pret.
P=
2
50
0
100 200 300 400 500 600 700 RPM
25
EPM
MOTORS
ORDERING INFORMATION
E P M
Euro
Planetary
Motor
Mounting Flange
no symbol - SAE A, two holes
F - magneto, four holes
Q - square, four bolts
W - wheel motor
Option
no symbol - without needle bearings
N* - with needle bearings
Porting
no symbol - side ports
E - rear ports
Displacement code
25 50 125 250 500
32 80 160 315 630
40 100 200 400
Threaded Ports
no symbol - Cilindrical seal thread - ISO 228
M - Metric thread - ISO 262
NOTES:
* Only with "D" Shaft Seal Versions!
** The permissible output torque for shafts must be not exceeded!
The following combinations are not allowed- Q, W, N versions with ...B shafts.
*** The following combinations are not allowed: Q flange, ...B- shafts and N options with U option.
The hidraulic motors are mangano-phosphatized as standard. Upon customer request they can be
additionally protected (painted).
26
HYDRAULIC MOTORS EPMM
The series of EPMM motors have a low speed, high torque capability. Converting hydraulic energy
into mechanical energy they are used extensively in the mobile, agriculture and industrial equipment
markets.
These units provide high output torque from a very small package. The motors are available in displacements from
8,2 cm /rev. to 50 cm /rev.
The EPMM motors are fixed displacement, gerotor type units that are known for compactness and economy.
All EPMM motors have built-in check valves assuring pressure on the shaft seal never exceeds pressure levels seen
in the return line.
EPMM series with EPMMP Series with Pressure Valve EPMMP Series with Pressure Valve
Check Valves A B, Dp=100 bar (50 bar) B A, Dp=100 bar (50 bar)
A
A A
B B
B
3
EPMM
MOTORS
SPECIFICATION DATA
* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 30 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
0
4. Recommended minimum oil viscosity 13 mm/s at operating temperature 50 C.
5. Recommended maximum system operating temperature is 82C.
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 15-30 min.
4
EPMM
EPMM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPMM 8
EPMM 12,5
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
5
EPMM
EPMM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPMM 20
EPMM 32
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
6
EPMM
EPMM
Motoren
MOTORS
FUNCTION DIAGRAMS
EPMM 40
EPMM 50
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
7
EPMM
MOTORS
DIMENSIONS AND MOUNTING DATA
max L
Porting Mounting
Rear Ports Standard Mounting
(without flange)
5,40,1 450,2
F - Mounting Flange
max L
11,70,3
21,20,15
C : 3xM6 12 mm depth
P (A, B): 2xG3/8; (M18x1,5), 12 mm depth
T : G1/8; (M10x1), 10 mm depth
40,30,3
Type L,mm Type L,mm Type L,mm Type L,mm Type L,mm Type L,mm Type L,mm Type L,mm L1,mm
EPMM 8 104 EPMMS 8 105 EPMMF 8 107,5 EPMMFS 8 108,5 EPMMP 8 115 EPMMPF 8 118,5 EPMMD 8 134 EPMMD(F) 8 137,5 3,5
EPMM12,5 106 EPMMS12,5 107 EPMMF12,5 109,5 EPMMFS12,5 110,5 EPMMP12,5 117 EPMMPF12,5 120,5 EPMMD12,5 136 EPMMD(F)12,5 139,5 5,5
EPMM 20 109 EPMMS 20 110 EPMMF 20 115,5 EPMMFS 20 116,5 EPMMP 20 120 EPMMPF 20 123,5 EPMMD 20 139 EPMMD(F) 20 145,5 8,5
EPMM 32 114 EPMMS 32 115 EPMMF 32 117,5 EPMMFS 32 118,5 EPMMP 32 125 EPMMPF 32 128,5 EPMMD 32 144 EPMMD(F) 32 147,5 13,5
EPMM 40 117,5 EPMMS 40 118,5 EPMMF 40 121 EPMMFS 40 122 EPMMP 40 128,5 EPMMPF 40 132 EPMMD 40 147,5 EPMMD(F) 40 151 17
EPMM 50 121,5 EPMMS 50 122,5 EPMMF 50 125 EPMMFS 50 126 EPMMP 50 132,5 EPMMPF 50 136 EPMMD 50 151,5 EPMMD(F) 50 155 21
8
EPMM
MOTORS
SHAFT VERSIONS
0,4
0,4
* * *
0
0
* For F Flange Motor - Mounting Surface
13040
Prad= (61,5+L) , [daN]
Prad
daN
[L in mm; L 80]
9
EPMM
MOTORS
ORDERING INFORMATION
E P M M
Euro
Planetary
Motor
Miniature
Adjustment Option
no symbol - without valve
P - side ports with pressure valve
D - side ports with dual cross port relief valve
Mounting
no symbol - without mounting flange, three bolts
F - with flange, two holes
Displacement code
8
12,5
20
32
40
50
Shaft *
C - 16, straight key 5x5x16 DIN 6885
VC - 16, straight key 5x5x16 DIN 6885 with corrosion resistance bushing
SH - splined, B17x14 DIN 5482
CK - 14, straight key 5x5x16 DIN 6885
Threaded Ports
no symbol - Cylindrical seal thread - ISO 228
M - Metric thread - I SO 262
Line to controled **
L -B A (left running)
R -A B (right running)
NOTES:
* The permissible output torque for shafts must be not exceeded!
** For P version useful only.
*** For P and D version useful only.
The hidraulic motors are mangano-phosphatized as standard. Upon customer request they can be
additionally protected (painted).
10
HYDRAULIC MOTORS EPMS
The gear set of the EPMS motor is comprised of rotor, stator and rollers. Apart of increasing the motor performance and
efficiency, the rollers reduce the friction and therefore increase the life of the motor.
To further improve the performance of the motors and reduce the power loss, M+S Hydraulic integrates a disc vale into the
motor. Moreover, the output shaft is mounted into a tapered roller bearing, which allows for the motors to withstand very
high radial and axial loads.
Based on its expertise in the production of hydraulic motors M+S Hydraulic has developed additional designs for specific
applications; the "W" design - for applications where is necessary to have direct drive such as in the "off highway"
equipment, and the "B" design - for applications with reverse brakes.
B
40
EPMS
MOTORS
SPECIFICATION DATA
* Intermittierent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 5 RPM lower than given, consult factory or your regional manager.
1) Intermittent speed and intermittent pressure must not occur simultaneously.
2) Recommended filtration is per ISO cleanliness code 20/16. A nominal foltration of 25 micron or better.
3) Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4) Recommended minimum oil viscosity 13mm/s at operating temperatures.
0
5) Recommended maximum system operating temperature is 82 C.
6) To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
41
EPMS
MOTORS
* Intermittierent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 5 RPM lower than given, consult factory or your regional manager.
1) Intermittent speed and intermittent pressure must not occur simultaneously.
2) Recommended filtration is per ISO cleanliness code 20/16. A nominal foltration of 25 micron or better.
3) Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4) Recommended minimum oil viscosity 13mm/s at operating temperatures.
0
5) Recommended maximum system operating temperature is 82 C.
6) To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
42
EPMS
MOTORS
FUNCTION DIAGRAMS
EPMS 80
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
EPMS 100
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
43
EPMS
MOTORS
FUNCTION DIAGRAMS
EPMS 125
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
EPMS 160
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
44
EPMS
MOTORS
FUNCTION DIAGRAMS
EPMS 200
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
EPMS 250
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
45
EPMS
MOTORS
FUNCTION DIAGRAMS
EPMS 315
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
EPMS 400
M
daNm
Int.
Cont.
Cont. Int. n
-1
min (rpm)
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
46
EPMS
MOTORS
Mounting
Porting Standard Mounting Flange
Side Ports
+0,2 +0,2
52 4x13,5 -0,1
C
106,40,2
max L
320,3
plugged
106,40,2
320,3
P(A,B)
106,40,2
C: 2xM10-12 mm depth
P(A,B): 2xG1/2 or 2xM22x1,5-20 mm depth
T: G or M14x1,5- 12 mm depth (plugged)
SHAFT VERSIONS
C 32, Paralel key A10x8x45 DIN 6885 K Tapered 1:10, Paralel key B6x6x20 DIN 6885
Max. Torque 77 daNm Max. Torque 77 daNm
4,50,1
35-0,039
min 16
56,50,4 +0,25
5
S=41, Tightening torque 580,4
201 daNm
CO 1" ,Paralel key 5 16"x 5 16 "x 1"BS46 SH Splined, 1" ANS B92.1-1976 standard
Max. Torque 77 daNm Max. Torque 77 daNm
min 19 min 16
Pitch 12/24
0,4 +2
Teeth 14 36
0
Pressure angle 30 56,50,4
1000,4
761
380,25
D
Motor - Mounting Surfase
48
EPMS
EPMS
Motors
MOTORS
T
max L
C
P(A,B)
+0,5
52
+0,2
-0,1
WE Version A
320,3 320,3
plugged
max L
P(A,B)
Acuating the brake level, the brake shaft is turned. The restangular shape of the inner part
of this shaft forces the brake pads to be pressed against the brake drum. This brakes the
wheel or the winch drum. Releasing the level, the spings pull it and the brake pads back A B
to the initial position. The motor output shaft is released.
0
Minimum angle adjustment is 10 . It can be adjusted by dismanting the level.
Depending on the application You can choose the acuating direction of the brake level.
The rod connection acuating the brake should be capable of moving at last 25 mm from
neutral to extreme position.
B Mounting Flange
F(s=5) D
E
max L
10,30,15
T
C
P(A,B)
+0,5
53
BE Version A
320,3 320,3
EPMSBR
plugged
max L
P(A,B)
EPMSBL
700,1
PL
A
MD
Type L, mm *L 1, mm L 2 , mm Type L, mm
PL
EPMSB 80 117 11,0 71 EPMSBE 80 127 900,2
max L
T
Mounting
min 23,8
max 27,1
Porting 4
+0,2
4x13,5 -0,1
Side Ports
60,2
plugged
320,3
C: 2xM10-12 mm depth
P(A,B): 2xG1/2 or 2xM22x1,5-20 mm depth +0,5
52
T: G or M14x1,5 - 12 mm depth (plugged)
46 -0,4
-1,0
For EPMSS
8,20,2
0,1 K
I T
2,30,05
0,25 K
+0,087
1070,2
290,5
400,1
350,5
min40
K
min 4
100
55 +1
321
15
G
F J
H 271
+0,2
27 +0,5
340,2
520,3
For EPMSZ
0,1 K
6,8+0,2 I T
min 29,7
2,30,05
0,125 K
-0, 25
13,21
+0,03
+0,054
min 15,3
+0,2
min 41,2
+0,05
34,8 +0,02
+0,1
27,8
34,82
109,5
43,9
101,6
-0,04
44
3
N
G
J
20
0
O
26,8 24,40,2
41,6
+0,5
17+0,5 0,8
52
EPMS
MOTORS
For EPMSV
H
E
53
EPMS
MOTORS
1
Pa=0daN
"A" and "B" are indicated on the end of the motor valve housing Pamax=500daN
max 67,15
Pamax=500daN
MD [daNm] 47
Pamax=500daN
MB [daNm]
54
EPMS
MOTORS
ORDERING INFORMATION
E P M S
Euro
Planetary
Motor
Model Series
Type
no symbol - standard motor
B - motor with drum brake
F - F mounting flange
Q - squere, mounting flange
S - short motor
V - very short motor
W - wheel mounting flange
Z - short motor, with place for needle bearing
Porting
no symbol - side ports
E - rear ports
Displacement code
80 160 315
100 200 400
125 250
Shaft*
C - 32, straight key A10x8x45 DIN6885
5 5
CO - 1" , straight key /1 6x /1 6x1 BS46
K - tapered 1:10 (35 under the seal)
SL - splined,p.t.o. DIN 9611 Form 1
SH - splined 14T ANS B92.1-1976
Threaded Ports
no symbol - Cylindrical seal thread - ISO 228
M - Metric thread - ISO 262
Actuating Direction**
R - right
L - left
NOTES:
* The permissible output torque for shafts must be not exceeded!
** Only for EPMSB
The hidraulic motors are mangano-phosphatized as standard. Upon customer request they can be
additionally protected (painted).
55
HYDRAULIC MOTORS EPMT
The new and more powerful EPMT series hydraulic motors have working displacements from
160 to 725 cm3/rev. and deliver 40 kW of power. Some of the main characteristics of this type
motors is that they have constant working displacement and achieve high torque at low speed.
The EPMT motor puts hydraulic power into work which is expressed in the direct relation between
flow rate and speed, and pressure and torque.
The main part of the EPMT motor is the gear set comprised of; rotor with 8 teeth, stator with 9
teeth and rollers. Apart of increasing the motor performance and efficiency, the rollers reduce
the friction and therefore increase the life of the motor.
The know how and expertise in the production of hydraulic motors has allowed M+S Hydraulic to achieve 129 (47)
daNm torque at 210 bar pressure and 172 (625) rev. at 125 l/min flow rate. In addition, by mounting the output shaft
into a tapered roller bearing, the EPMT series motors can withstand very high radial and axial loads.
The W design was developed specifically for applications where is necessary to have direct drive such as in the off
highway equipment.
EPMT Series
with Check Valves Pressure Losses
B
56
EPMT
MOTORS
SPECIFICATION DATA
* Intermittierent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 5 RPM lower than given, consult factory or your regional manager.
57
EPMT
MOTORS
FUNCTION DIAGRAMS
EPMT 160
Cont.
Cont.
EPMT 200
Cont.
Cont.
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
758
EPMT
MOTORS
FUNCTION DIAGRAMS
EPMT 250
EPMT 315
Cont.
Cont.
759
EPMT
MOTORS
FUNCTION DIAGRAMS
EPMT 400
Cont.
Cont.
EPMT 500
Cont.
Cont.
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
760
EPMT
MOTORS
Porting Mounting
Side Ports Standard Mounting Flange
P(A,B)
W Mounting Flange
E Rear Ports
P(A,B)
plugged
T
C: 4xM10-10 mm depth
P(A,B): 2xG3/4 or 2xM27x2-17 mm depth
T: G 1/4 or M14x1,5 - 12 mm depth (plugged)
Shaft Versions
C 40, Parallel key A12x8x70 DIN 6885 K Tapered 1:10, Parallel key B12x8x28 DIN 6885
Max. Torque 132,8 daNm Max. Torque 210,7 daNm
+0,2
6,3
56
min 25
90,25
79,50,2
540,4
820,2
CO 1" ,Parallel key 3 8"x 3 8"x 21 4" BS46 SH 17T Splined, 1" DP 12/24 ANS B92.1-1976 standard
Max. Torque 132,8 daNm Max. Torque 132,8 daNm
min 25 min 25
45
O
45O
78,50,2 78,50,2
62
EPMT
MOTORS
Porting Mounting
Side Ports S - Short Mounting Flange
max 36,1
min 32,9
C 4x14,2
+0,4
P(A,B)
"O" Ring 125x3
T 80,2
Drain port
720,2
max L
max +0,5
max L 90,5 -1,6
C : 4xM10-10 mm depth
P (A,B): 2xG3/4 or 2xM27x2-17 mm depth
T : G or M14x1,5 - 12 mm depth (plugged)
63
EPMTS
EPMT
MOTORS
DIMENSIONS OF THE ATTACHED COMPONENT
EPMTS
+1
92
EPMTV
depth min
Four
64
EPMT
Motoren
MOTORS
1000
0
50 100 150 180 (mm)
max 114
DIRECTION OF SHAFT ROTATION
Pamax=1000 daN
B A B A
max 181
Pamax=1000 daN
65
EPMT
MOTORS
ORDERING INFORMATION
E P M T
Euro
Planetary
Motor
Toil Series
Type
no symbol - standard motor
S - short motor
V - very short motor
W - wheel mounting flange
Porting
no symbol - side ports
E - rear ports
Shaft*
C - 40, straight key A12x8x70 DIN 6885
3 3
CO - 1" , straight key /8x /8x2 BS46
K - tapered 1:10 (45 under the seal)
SL - splined,p.t.o. DIN 9611 Form 1
SH - splined 17T ANS B92.1-1976
Threaded Ports
no symbol - Cylindrical seal thread - ISO 228
M - Metric thread - ISO 262
Note: * The permissible output torque for shafts must be not exceeded!
The hidraulic motors are mangano-phosphatized as standard. Upon customer request they can be
additionally protected (painted).
66
HYDRAULIC MOTORS EPRM
The series of EPRM motors have a low speed, high torque capability. Converting hydraulic energy into
mechanical energy they are used extensively in the mobile, agriculture and industrial equipment markets.
These units provide high output torque from relatively small packages. The motors are available in displacements
3 3
from 51,5 cm /rev. to 397 cm /rev. with speeds up to 1000 RPM.
The EPRM motors are fixed displacement, geroler type units that are known for dependability and performance.
All EPRM motors have built-in check valves assuring pressure on the shaft seal never exceeds pressure levels seen in
the return time.
B B
27
EPRM
MOTORS
SPECIFICATION DATA
* Intermittent operation: the permissble values may occur for max. 10% of every minute.
** Peak load: the permissble values may occur for max. 1% for every minute.
*** For speeds of 10 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simultaneously!
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommended using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm/s at operating temperatures.
5. Recommended maximum system operating temperature - 82C.
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 min.
28
EPRM
MOTORS
* Intermittent operation: the permissble values may occur for max. 10% of every minute.
** Peak load: the permissble values may occur for max. 1% for every minute.
*** For speeds of 10 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simultaneously!
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommended using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm/s at operating temperatures.
5. Recommended maximum system operating temperature - 82C.
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 min.
29
EPRM
MOTORS
* Intermittent operation: the permissble values may occur for max. 10% of every minute.
** Peak load: the permissble values may occur for max. 1% for every minute.
*** For speeds of 10 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simultaneously!
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommended using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm/s at operating temperatures.
5. Recommended maximum system operating temperature - 82C.
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 min.
30
EPRM
MOTORS
Type EPRM EPRM EPRMW EPRM EPRM EPRMW EPRM EPRM EPRMW
250 250...B 250 315 315...B 315 400 400...B 400
Displacement, [cm /u]
3
250,1 250,1 250,1 315,7 315,7 315,7 397 397 397
Max. Speed, cont. 240 240 240 190 190 190 150 150 150
[RPM] int.* 300 300 300 240 240 240 190 190 190
Max. Torque cont. 39 54 54 39 55 55 38 61 61
[daNm] int.* 58 61 61 57 63 63 60 69 69
peak** 71 71 71 83 83 83 87 87 87
Max. Output, cont. 6,5 10 10 6 9 9 4,8 7,8 7,8
[kW] int.* 10,5 12 12 9,6 11 11 8,8 10,6 10,6
Max. Pressure Drop cont. 110 175 175 90 135 135 70 115 115
[bar] int.* 175 200 200 140 160 160 115 140 140
peak** 225 225 225 210 210 210 175 175 175
Max. Oilflow cont. 60 60 60 60 60 60 60 60 60
[l/min] int.* 75 75 75 75 75 75 75 75 75
Max. Inlet Pressure cont. 175 175 175 175 175 175 175 175 175
[bar] int.* 200 200 200 200 200 200 200 200 200
peak** 225 225 225 225 225 225 225 225 225
Max. Return Pressure cont. 150 100 100 150 100 100 150 100 100
w/o Drain Line or 0-100 RPM
max. Pressure in Drain cont. 75 30 50 75 30 50 75 30 50
Line, [bar] 100-300 RPM
int.* 0-max. RPM 150 100 100 150 100 100 150 100 100
Max. Return Pressure cont. 175 175 175 175 175 175 175 175 175
with Drain Line int.* 200 200 200 200 200 200 200 200 200
[bar] peak** 225 225 225 225 225 225 225 225 225
Max. Starting Pressure 4 4 5 3 3 5 3 3 5
with Unloaded Shaft, [bar]
Min. Starting Torque at max. press. 31 50 50 33 50 50 30 49 49
[daNm] drop cont.
at max. press. 48 55 55 58 66 66 50 61 61
drop int.*
Min. Speed***, [RPM] 10 10 6 10 10 5 10 10 5
Weight, avg., [kg] EPRM (F) 8,4 8,5 9,1 9,2 9,8 9,9
EPRMW 7,8 8,6 9,3
EPRMQ 12,1 12,6 13,3
* Intermittent operation: the permissble values may occur for max. 10% of every minute.
** Peak load: the permissble values may occur for max. 1% for every minute.
*** For speeds of 10 RPM or lower, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure drop must not occur simultaneously!
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommended using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM (ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm/s at operating temperatures.
5. Recommended maximum system operating temperature - 82C.
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 min.
31
EPRM
MOTORS
FUNCTION DIAGRAMS
EPRM 50
EPRM 80
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
32
EPRM
MOTORS
FUNCTION DIAGRAMS
EPRM 100
EPRM 125
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
33
EPRM
MOTORS
FUNCTION DIAGRAMS
EPRM 160
EPRM 200
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
34
EPRM
MOTORS
FUNCTION DIAGRAMS
EPRM 250
EPRM 315
The function diagrams data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
35
EPRM
MOTORS
FUNCTION DIAGRAM
EPRM 400
The function diagram data was collected at back pressure 510 bar
and oil with viscosity of 32 mm/s at 50 C.
Dp
bar
1 1: Drawing for "D" Seal
150
2: Drawing for EPRMW Seal
3: Drawing for ...B" Shaft Seal
4: Drawing for Quadring
B B
A
2
A
100
80 3
60
36
EPRM
MOTORS
DIMENSIONS AND MOUNTING DATA
max L
Porting Mounting
Standard Mounting Flange
550,1
+0,4
2x13,35
Side Ports
max 107,5
E Rear Ports
550,1
max 107,5
Q - Mounting Flange 4-Holes
Square
550,1
C : 4xM8 - 13 mm depth
P (A,B) : 2xG1/2 or 2xM22x1,5 - 20 mm depth
min 15
T : G1/4 or M14x1,5 - 12 mm depth (plugged) max 107,5
37
EPRM
MOTORS
Lh=2500 h
38
EPRM
MOTORS
ORDERING INFORMATION
E P R M
Euro
Planetary
Motor
Mounting Flange
no symbol - SAE A, two holes
F - magneto, four holes
Q - square, four bolts
W - wheel motor with bearings
Option
no symbol - without needle bearings
N* - with needle bearings (not valid for EPRMW)
Porting
no symbol - side ports
E - rear ports
Displacement code
50 125 250
80 160 315
100 200 400
Threaded Ports
no symbol - Cilindrical seal thread - ISO 228
M - Metric thread - ISO 262
NOTES:
* Only with "D" Shaft Seal Versions!
** 1) The permissible output torque for shafts must be not exceeded!
2) The following combinations are not allowed- Q, N versions with ...B shafts.
3) EPRMW is only available with CB and KB shafts.
*** The following combinations are not allowed: Q and W flange, ...B- shafts and N options with U option.
The hidraulic motors are mangano-phosphatized as standard. Upon customer request they can be
additionally protected (painted).
39