You are on page 1of 9

EMCPII Service mode

OP1
PHASE ENGINE LAMP ALARM SERVICE
EXIT
SELECT METER TEST CODE MODE

SCROLL SCROLL SCROLL SELECT ENTER


RIGHT UP DOWN

OP1 FAULT LOG VIEWING


OP4 Fault log clearing
OP2 SETPOINT VIEWING
OP5 Set point programming
OP3 PASSWORD ENTRY
OP6 Spare Input/Output programming

OP7 Hourmeter programming

PE: 13231 OP8 Voltmeter/Ammeter programming

OP9 Engine setpoint verification

OP10 AC offset adjustment


EMCPII+ Service mode

OP1
PHASE ENGINE LAMP ALARM SERVICE
EXIT
SELECT METER TEST CODE MODE

SCROLL SCROLL SCROLL SELECT ENTER


RIGHT UP DOWN

OP1 FAULT LOG VIEWING


Fault log clearing
OP4
ENGINE / GENERATOR
OP2-0 SETPOINT VIEWING OP5-0 Engine/Generator programming
PROTECTIVE RELAYING
OP2-1 SETPOINT VIEWING OP5-1 Protective Relaying programming

OP2-2 FACTORY CALIBRAT OP6 Spare Input/Output programming

OP3 PASSWORD ENTRY


OP7 Hourmeter programming

OP8 Voltmeter/Ammeter programming

OP9 Engine setpoint verification


PE: 13231 OP10 AC offset adjustment
EMCP II+ OP5-0 setpoints
P001 fuel solenoid type 0=ETR, 1=ETS
P002 Units shown 0=Eng, metric
P003 Shutdown override for Engine fault 0=Shutdown, 1=Alarm
P004 Shutdown override for for Sensor fault 0=Alarm, 1=Shutdown
P005 Coolant loss sensor installed 0=w/o sensor, 1=w/sensor
P006 Shutdown override for coolant loss fault 0= shutdown, 1= alarm
P007 System voltage 24 volts or 32 volts
P008 Not used NA
P009 Number of ring gear teeth 95 to 350 teeth
P010 Engine overspeed 500 to 4330 rpm
P011 Crank terminate speed 100 to 1000 rpm
P012 Oil step speed 400 to 1800 rpm
P013 Low oil pressure shutdown at Rated speed 34 to 240 kPa (5 to 61 psi)
P014 Low oil pressure shutdown at Idle speed 20 to 336 kPa (3 to 49 psi)
P015 High water temperature shutdown 85 to 123 C (185o to 253oF)
P016 Low water temperature alarm 0 to 36oC (32 to 97oF)
P017 Total cycle crank time 5 to 360 seconds
P018 Cycle crank time 5 to 300 seconds
P019 Cooldown time 0 to 30 minutes
P020 AC voltage 150V to 30.0 kV
P021 AC current full scale 75A to 4000A
P022 GSC Engine Number 01 to 08
P023 Engine type 0=MUI, 1=Gas, 2=EUI
P024 Crank time delay (only for gas) 0 to 20 seconds
P025 Oil temperature sensor installed 0=w/o sensor, 1=w/sensor
P026 High oil temperature shutdown 85 to 123oC (185 to 253oF)
P027 Shutdown enable for high oil temperature 0=alarm, 1=shutdown
P028 Name plate voltage 100 to 25kV
P029 Name plate Current 0 to 4000A
P030 Name plate power 0 to 10MW
P031 Rated frequency 50, 60 or 400 Hz
P032 Connection configuration of generator 0=wye, 1=delta
P033 Number of generator poles 0 to 254
E M C P II
The response of the EMCP to a fault will depend
on the set point programming ( OP-5 )

P03 Shutdown override for ENGINE fault


This set point tells the GSC how to respond to a low engine oil pressure or
high coolant temperature fault.
They are not diagnostic faults but engine faults.
The setting are : 0 - for shutdown
1 - for alarm only

P04 Shutdown override for SENSOR fault


The diagnostic faults are : Oil pressure sensor
Coolant temp sensor
Coolant loss sensor
Sensor power supply
They are diagnostic faults (bad sensor, wiring)not engine faults.
The setting are : 0 - for shutdown
1 - for alarm only
EMCPII & ECM

Cat data link

MPU
EMCP II

ECM
GEN

Speed/timing Sensor

Engine Coolant Engine oil


Temperature Sensor Pressure Sensor
E M C P II & E C M

If there is an E present in the diagnostic


code the ECM is generating the code, proceed
to troubleshot using SENR1003 3500B Gen
Set Engine Troubleshooting Service Manual.

91 E 8
ECM is generating the diag code
E M C P II & E C M

91 E 8 Speed control output Signal is Abnormal


Marine
This is a common fault when you have a
3500B using a load sharing module and the
engine is not running (there is no power to the
LSM therefore there is no PWM output to the ECM)
Truck

EPG
TRIM
POT

Load sharing module


1 2 3
Speed control
Gain Droop
(Converter)
-B S D +B
EMCP II Service Manual
Publications

SERVICE MANUALS EMCPII EMCPII+


MUI SENR5809-04 SENR5832-01
PEEC SENR5827-01 RENR1254
EUI SENR5398-02 RENR1200-01
GAS SENR5394 RENR1201

FG Wilson Packages RENR1250 (3306,3406 MUI) RENR1260 (3500 EUI)


RENR1261 (3412,3500 MUI) RENR1249 (3306,3406 MUI)
RENR1259 (3500 EUI) RENR1253 (3412,3500 MUI)

You might also like