Professional Documents
Culture Documents
https://ourtechplanet.com/pci-planning-facts-myths/
PCI planning is one of the most important things to understand while planning an LTE network
and it is usually left untouched in most of the LTE manuals and text-books. As already
explained, the PCI is decoded using the SSS and the PSS and can be given by the following
equation
PCI = 3*SSS + PSS
So, if SSS is equal to 5 and PSS is equal to 1 then the PCI would be 16. A basic rule of thumb is
that the neighboring cells should not have the same PSS value. Usually, a site with 3 cells use
same SSS value but different PSS value such that the PCIs for cell 1,2 and 3 will be 0,1 and 2.
Within the cell, the channels are scrambled using the PCI which means that the PCI serves as the
seed for the cells permutation algorithm. Thats why, the UE has to decode the PSS and SSS
before reading any other channel as it needs to get the PCI which tells about the permutation
used in the cell.
Since we have 504 PCIs so this rule is usually not difficult to follow.
The same site should not use the same PCI again on the same frequency
The NBRs of the site should not have the same PCI on the same frequency
Ideally, two NBRs of the site should not have same PCI between them. For instance,
Cell-A has NBR Cell-B and Cell-C and both of them have the same frequency, then the
PCI of Cell-B and Cell-C should not be identical. This is difficult to maintain in a LTE
network but this issue can cause PCI confusion and handover failures
However, if the system is only a single port system like most of the IBS systems, then the PCI
mod3 will not impact because there will be no reference signals on the second port. Instead, the
rule will change to PCI mod6.
An important point to remember is that most of the FDD LTE networks are not time
synchronized between sites so the symbols do not usually overlap in time. Therefore, for FDD
systems, this rule is not as important as it is for TDD LTE systems which are always time
synchronized.
In LTE, the PCFICH is one of the channels that gets its location determined based on the PCI.
This also means that every PCFICH will repeat its position for some PCIs. Basic rule is that
every 50th PCI will have same location of PCFICH for 20MHz channel while every 25th PCI
will have same location of PCFICH for 10MHz channels. Such a scenario can cause decoding
failures or higher block error rate on PCFICH and since PCFICH is required to decode PDCCH
so it can cause DTX (decoding failure of grants on PDCCH).
But once again it is difficult to observe in FDD systems and another fact that most of the
documents overlook is that PCFICH consists of 4REGs. Each REG has 4 REs but we have
reference signals in a LTE system after every 2 REs. So, each PCFICH REG will have Reference
Signals embedded inside and that means that 2 PCFICHs usually do not overlap each other
completely.
There is another known rule that is not really considered as it has no evident impact but I thought
it is worth mentioning. As explained, each PCI is made up of PSS and SSS. Each SSS is made up
of two length-31 binary m-sequences (m0 and m1) but since SSS are 168 in count so these
length-31 sequences are bound to repeat. So, each time m0 or m1 repeat itself, the overall
correlation between those 2 SSS values is much higher in other words such SSS can interfere
with each other. As an example, SSS value of 9 can have interference with 10 other SSS values.
However, this type of interference has no effect on KPIs and if the UE fails to decode SSS in
first subframe, it can still decode it in the 6th subframe as SSS repeats twice within 10ms. So,
such an issue, if observed might delay network entry by 5 to 10 ms which does not have any
considerable impact.
If you have any questions or feedback regarding PCI Planning, simply drop a comment below
and I will surely get back to you.