Professional Documents
Culture Documents
RMCS-3001
Brushless DC motor Driver
(Max. 48VDC and 5A per phase)
http://www.rhinomc.com
Page 1
Contents
2.3 Applications 6
http://www.rhinomc.com
Page 2
List of Tables
http://www.rhinomc.com
Page 3
Read this document carefully before installing and utilizing the drive
Use multi-meter to verify the voltage supplied is within Maximum ratings.
Never plug or unplug motor terminals while the driver is in ON condition; else it may
damage the driver.
To avoid personal injury and property loss, only qualified and service-trained personnel
should operate the driver.
Do not insert any object into the driver, which may cause damage to the driver.
If any fault occurs to the driver while operations, please return it for maintenance/repair.
Trying to repair the driver without any authorization or improper operation may cause
damage to the driver and void the warranty clause.
Input voltage to the driver must not exceed the maximum of 48VDC.
Supplying Reverse polarity input voltage will damage the Driver.
Connecting the power supply wires to the motor coil terminals will damage the
driver.
Excess humidity or condensation can damage the driver.
Heat sink is designed to dissipate heat from the driver circuitry as long as the
ambient temperature is less that 70C degrees Celsius. Ambient temperature in
excess of that may damage the driver.
While changing the Direction, apply 5V or 0V to DIR pin. Power reset is necessary for
implementing Dir change.
http://www.rhinomc.com
Page 4
The ENABLE, BRAKE and DIRECTION inputs are optically isolated. These inputs work with
3.3V or 5V logic drive signals. Motor will run on application of 3.3V/5V to ENABLE pins. To
facilitate the direction change of Motor shaft, dedicated DIR pin is given. After applying the
3.3V/5V to DIR pin, Power reset is required. BRAKE feature provided for braking the motor
rotation.
http://www.rhinomc.com
Page 5
2.3 Applications:
Typical applications include CNC routers, laser cutters, laser markers, medical equipments,
X-Y tables, measurement equipments, etc.
http://www.rhinomc.com
Page 6
http://www.rhinomc.com
Page 7
Specification Details
Weight 155gms
http://www.rhinomc.com
Page 8
There is a two LED on this drive for power and error status messages. Green LED is
provided for power and red LED is for error indication.
Resolution Description
Pot-1 Potentiometer for speed control
Pot-2 Current Setting (Inside chassis)
Potentiometer:
http://www.rhinomc.com
Page 9
Current:
The user can self test the driver if the power supply section is OK (if green LED glows).
For self testing connect the motor phase properly and make sure that LED status is
correct. Supply the 3.3v/5V to enable pin to enable the rotation of motor shaft. Also
change the current settings in potentiometer if necessary. Current setting
potentiometer is provided inside the drive. You need to remove the top to change the
current gain. Speed can be altered using external potentiometer. Also check whether
direction and Brake states are working by connecting the corresponding pins to +5V
with respect to ground. These are the steps to check the basic functionality of a drive.
The table given below shows some user level trouble shooting tips which may useful
while working with RMCS-3001 with an external pulse generator.
http://www.rhinomc.com
Page 10
Six-Month Warranty
Rhino Motion Controls (rhinomc.com) warrants its products against defects in materials and workmanship for a period of 6
months from shipment delivery. During the warranty period, Rhino Motion Controls will either, at its option, repair or
replace products which proved to be defective.
Exclusions
The above warranty does not extend to any product damaged by reasons of improper or inadequate handlings by
customer, improper or inadequate customer wirings, unauthorized modification or misuse, or operation beyond the
electrical specifications of the product and/or operation beyond environmental specifications for the product.
To obtain warranty service, please contact our customer service department at info@rhinomc.com before returning
product for service. Please make sure that you have gone through this entire installation manual and datasheet before
deciding that your product is liable for replacement or repair under this 6-month warranty Customer shall prepay shipping
charges for products returned to Rhino Motion Controls for warranty service, and Rhino Motion Controls shall pay for
return of products to customer.
Warranty Limitations
Rhino Motion Controls makes no other warranty, either expressed or implied, with respect to the product. Rhino Motion
Controls specifically disclaims the implied warranties of merchantability and fitness for a particular purpose. Some
jurisdictions do not allow limitations on how long and implied warranty lasts, so the above limitation or exclusion may not
apply to you. However, any implied warranty of merchantability or fitness is limited to the 6-month duration of this written
warranty.
Disclaimer
http://www.rhinomc.com
Page 11