Professional Documents
Culture Documents
Service Manual
XA25
XA20
VIXIA HF G30
LEGRIA HF G30
English Edition
SAFETY PRECAUTIONS
The following precautions should be observed when servicing.
1. Since many parts in the unit have special safety-related characteristics, always use genuine CANON replacement parts.
Especially critcal parts in the power circuit block should not be replaced with other makes.
Critical parts are marked with in the schematic diagrams.
2. When servicing, observe the orginal lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
4. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
4-1 Leakage Current Cold Check
1) Unplug the AC cord and connect a jumper between the two prongs on the plug.
2) Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metalic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metalic part
has a return path to the chassis, the reading should be between 1M and 5.2M. When the exposed metal does not have a return path to the chassis, the reading must be .
4-2 Leakage Current Hot Check
1) Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2) Connect a 1.5K 10 watt resistor, paralleled by 0.15F capacitor, between each exposed metalic parts on the unit and a good earth ground such as a water pipe, as shown in the figure below.
3) Use an AC voltmeter, with 1000 / volt or more sensitivity, to measure the potential across the resistor.
4) Check all exposed metallic parts of the cover (Cable connection, Handle bracket, metallic cabinet. Screwheads, Metallic overlays, etc),
and measure the voltage at each point. AC VOLTMETER
5) Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6) The potential at any point should not exceed 0.75V RMS.
A leakage current tester (FLUKE MODEL : 8000A equivalent) may be used to make the hot checks.
DEVICE
Leakage current must not exceed 0.5 milliamp. UNDER
TEST 1.5K
In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and corrective action must be taken Test all
before returning the instrument to the customer. exposed 0.15F
metal parts
Water pipe
(Earth Ground)
AC OUTLET Figure 1. Leakage Current Hot Check
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 TECHNICAL DESCRIPTION
CONTENTS
1: PCB Functions.............................................................................................................................................................................................. 2
2: Interconnection Diagram............................................................................................................................................................................... 3
3: Power Fuses................................................................................................................................................................................................. 4
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 TECHNICAL DESCRIPTION
1: PCB Functions
MAIN UNIT HANDLE UNIT HDU-1
(1) MAIN PCB (15) XLR AUDIO PCB
Camera signal processing, Recorder signal processing(DIGIC DV 4) XLR audio signal processing, XLR amplifier
FLASH ROM for DIGIC DV4(256Mbit) INPUT SELECT SW(CH1/CH2), INPUT SENS SW(CH1/CH2), ON/OFF SW
DDR SDRAM for DIGIC DV4(4Gbit) REC LEVEL VOLUME(CH1/CH2)
System control Infrared light, Tully lamp
Lens driving/control (16) XLR POWER PCB
Power DC/DC converter Power DC/DC converter
Electric charge control (17) XLR MICOM PCB
Wi-Fi control(LUGH) Key detection on the handle unit
DDR SDRAM for LUGH(256Mbit) START/STOP button, Zoom-Wide SW, Zoom-Tele SW
FLASH ROM(4M bits) for Wi-Fi user setting storage (18) XLR JACK PCB
Analog input/output signal processing for AUDIO XLR1 jack, XLR2 jack
HDMI control
SDI signal processing(XA25 only)
Velocity detection(ROLL)
(2) CMOS SENSOR PCB
CMOS image sensor
Sensor output signal A/D conversion
(3) CARD-A PCB
Card slot A
Velocity detection(YAW, PITCH)
(4) CARD-B PCB
Card slot B
(5) WIFI PCB
Wireless LAN module
(6) MIC JACK PCB
MIC jack, HEADPHONE jack
(7) TRIGGER PCB(In LEFT COVER UNIT)
START/STOP button, FUNC. button, Joystick
(8) MODE PCB(In LEFT COVER UNIT)
AUTO/M/CINEMA mode SW
(9) DC JACK PCB
DC jack, AV jack
(10) CARD OPEN PCB
Card cover open/close detection SW
(11) JACK PCB
HDMI jack, USB jack, REMOTE jack
(12) LCD PCB
Touch panel control, LCD to LVDS/PARALLEL signal conversion
(13) LCD B/T SW PCB(In RIGHT COVER UNIT)
Panel reversal detection SW
(14) CVF PCB(In CVF UNIT)
CVF to LVDS/PARALLEL signal conversion, CVF signal processing/driving
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 TECHNICAL DESCRIPTION
2: Interconnection Diagram
HANDLE UNIT
LEFT COVER ASS'Y
(XA25, XA20 only)
CN5300
IC5361 IC5360
CN5471
CN5301
IC5301 CN5470
CN621
IC5302
XLR AUDIO PCB
IC5300
IC620
XLR JACK PCB
CN600
IC621
CN620
CN601
IC5384 IC5385
IC3400
HDMI USB
JACK JACK
CN122 CN1701
CN1700 MAIN-HANDLE FPC
(XA25, XA20 only)
MAIN-ACC FPC
(VIXIA HF G30, LEGRIA HF G30 only)
AV DC
JACK JACK
CN900
CN1040
CN802
IC1100 IC102
CN1100
IC701
MAIN PCB IC3200
IC104
CN1801
IC1800
IC2800 IC103 IC3430
IC2850 IC100 IC3420
CN1802
IC3450
IC2851 IC2230
CN2800
IC6000 IC901
CN1105 IC6001
CN2801 CN2900 CN801
CN4000
CN902
CN103
CN102
CN901
AF SENSOR ASS'Y IC905
LCD PCB
CN903
CN4501
IC4501
Metal contact (Pins' face down) Metal contact (Pins' face up)
CN4100
CN4200
BAT100
CN120
CN170
Metal contact Metal contact
CARD B PCB CARD A PCB
CN171
RIGHT COVER ASS'Y
CARD OPEN PCB
CMOS DIAL ASS'Y
REAR COVER ASS'Y
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 TECHNICAL DESCRIPTION
3: Power Fuses
Handle Unit HDU-1 (XA25, XA20 only)
Camera Body XLR POWER PCB
MAIN PCB FU3200 FU3400
SHOE UNREG CN1901 ACC. SHOE REAR CN CN600 DC/DC
FU3201 FU3401
VTR UNREG 8.5V, P5V, 48V,
AA8.5V, 5V, F48V_OUT
FU3300
1.0V, 1.8V, 3.3V
FU3301
REAR FPC 1.2V
BATT TERMINAL CN1802
FU3302
BATT+ BATT+ P5V, AA4.6V
FU3304
CN1800 Q1801 3.2V
DC+
FU3305
DC JACK PCB 3.8V
DC JACK CN1801
FU3206 FU1800
DC+ DC+ CHARGE UNREG
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
CONTENTS
1: Disassembling and Reassembling....................................................................... 2 1-27: Disassembly of Handle Unit 4..............................................................................27
1-1: Disassembling / Reassembling Flowchart...............................................................3 1-28: Disassembly of Handle Unit 5..............................................................................28
1-2: Separation of Handle Unit (XA25, XA20 only) and Lens Hood................................4 1-29: List of Screws Used.............................................................................................29
1-3: Separation of Bottom Cover.....................................................................................4
1-4: Separation of Top Cover Ass'y.................................................................................5
1-5: Separation of Left Cover Ass'y.................................................................................6
1-6: Separation of Rear Top Cover Ass'y and WIFI PCB................................................7
1-7: Separation of R-LCD Unit........................................................................................8
1-8: Separation of Front Cover Ass'y..............................................................................9
1-9: Separation of Top Frame and Top Heatsink Sheet.................................................10
1-10: Separation of MAIN-HANDLE FPC (XA25, XA20 only) and
MAIN-ACC FPC (VIXIA HF G30, LEGRIA HF G30 only)....................................11
1-11: Separation of Color View Finder Ass'y.................................................................12
1-12: Separation of Rear Cover Ass'y...........................................................................12
1-13: Separation of DC PCB.........................................................................................13
1-14: Separation of L Jack Unit.....................................................................................14
1-15: Disassembly of L Jack Unit..................................................................................15
1-16: Separation of AF Sensor Ass'y............................................................................16
1-17: Separation of MAIN PCB.....................................................................................17
1-18: Separation of Main R Frame Unit.........................................................................18
1-19: Separation and Disassembly of Card Holder Unit...............................................19
1-20: Disassembly of R-LCD Unit.................................................................................20
1-21: Separation of LCD Unit........................................................................................21
1-22: Disassembly of LCD Unit.....................................................................................22
1-23: Disassembly of Camera Unit...............................................................................23
1-24: Disassembly of Handle Unit 1..............................................................................24
1-25: Disassembly of Handle Unit 2..............................................................................25
1-26: Disassembly of Handle Unit 3..............................................................................26
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(1) When replacing the flat cable with a new one, allow it to remain folded the same as the original Item Name Item Number Purpose Remarks
part. Adhesive Tape, No. 354E DY9-3032-000 General-purpose adhesive White
(W L T : 9mm 50m 0.15mm, UL type) tape
(2) The flat cable has a contact orientation to be engaged with the connector. Refer to the instructions Adhesive Tape, No. 501F DY9-3034-000 General-purpose
in the disassembly procedure diagram and interconnection diagram for boards. (W L T : 10mm 50m 0.16mm, UL type) double-sided adhesive tape
Three Bond 1401C CY9-8011-000 For preventing screws from AF Sensor Ass'y
loosening
Lateral engaging connector Lengthwise engaging connector Hanarl FL-778 DY9-3026-010 Lubrication Rear Connector
(The instructions are given in the disassembly procedure (The instructions are given in the disassembly Cushion
Insulating Tape CY9-4044-000 General-insulating tape Transparency
diagram and board interconnection diagram.) procedurediagram and board interconnection diagram.) (W L T : 25mm 30m 0.05mm)
:Contacts are positioned downward. Indicated by Arrowheads indicate the contacts, and Sucker Commercial item For detaching LCD Top Disasembly of
(Diameter : About 25-30mm, Cover Ass'y Panel section.
(board side) the shafts indicate the noncontacts.
Diameter of the adsorption time : 50mm or less)
:Contacts are positioned upward.
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
START
Main Flow
Sub Flow
1-2 : Handle Unit *1 1-24 : Microphone Holder Ass'y 1-25 : XLR POWER PCB 1-26 : XLR JACK PCB 1-27 : XLR AUDIO PCB 1-28 : Front Screw Cover *1: XA25/XA20 only
XLR MICON PCB Handle Front Screw Sleeve
(Note) XA20: The Handle Unit of JP Model is sold separately.
Handle Front Ring *2: VIXIA HF G30/
Handle Front Shoe Screw LEGRIA HF G30 only
Handle Front Shoe Plate
1-2 : Dash Cover *4 *3: XA25 only
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
1-2: Separation of Handle Unit (XA25, XA20 only) and Lens 1-3: Separation of Bottom Cover
Hood (1) Detach the Grip Belt.
(1) Loosen Rotate Ring and two screws, and then detach the Handle Unit. (XA25, XA20 only) (2) Remove 12 screws (b9, c2, d1), and then detach the Bottom Cover.
(1) Remove two screws (a2), and then detach the Dash Cover. (XA20 (JP Model) only)
(2) Detach the Lens Hood and Lens Cap.
b DB1-6044-000 (BLACK)
6.0mm
b
XA25, XA20 only b b M1.7
(SELF TAP)
5.0mm
Screw b M1.7
(SELF TAP)
(1)
(1)
Grip Belt
(1) Dash Cover
(2) c
Lens Hood
(2)
(2) (1)
a DB1-6208-000 (BLACK)
(1)
(2)
8.0mm
M3.0
Lens Cap
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
e e
f DB1-0948-000 (BLACK)
(1)
f
4.5mm
M1.7 Step 1
(2)
Insert the rib under the Left Cover Ass'y
Top Cover Ass'y and attach the Top Cover Ass'y.
(2)
Step 2
Fasten the screws with the Front Handle Shoe
e pressed Left Cover Ass'y to the arrow direction.
(2) Press
LCD
Step 3
Fasten the four screws f.
(2)
f
(2)
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(1) Attach the Left Cover Ass'y as shown in the figure. Screw holes
Jack Cover
c DA3-8806-000 (BLACK) d DB1-6045-000 (BLACK) g DA3-8804-000 (BLACK) Left Cover Ass'y
Step 1
5.0mm 5.5mm 2.5mm
M1.7 Attach the Jack Cover, position with
M1.7 M1.7 SELF LOCK SCREW respect to the screw holes, and
(SELF TAP) (2) attach the Left Cover Ass'y.
Finder Part
Speaker Holder
i Press
(1)
g Left Cover Ass'y
d
(1)
g Press
(1) Step 3
Fasten the remaining screws.
Then, fasten the screws of the upper section with
(1) d the Left Cover Ass'y pressed in the direction of
c c c the arrow.
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(2) (2)
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(2)
m CN103
m R-LCD Unit LCD f IR Knob
CN900
Step 2 l
Align the phase. Step 3
m Step 1
Fasten the screws of the R-LCD Unit side
(2) Align the phase of the IR Knob with that Connect the CN103, CN122,
m of the switch and attach the R-LCD Unit.
face first. After fastening the screws, check
and CN900 and engage the
if the Cassette IR Knob operates.
LCD cables with the ribs.
(2) Note on Reassembling (2) Connect the CN900 as shown in the figure.
(2) (Hereafter, connect connectors of identical
configuration in the same way.)
(2) Protrusion from the bottom Insert the connector by applying simultaneous, even
(2) section of the main unit is pressure with the fingers to the locking sections at
not allowed. the ends.
f
Insulating Tape (9 30mm)
R-LCD Unit Do not press the center of After attaching, check
(1) Insulating Tape (9 30mm) the connector. Position the if there is no floating
Insulating Tape (9 30mm)
l R-LCD Unit
connectors in parallel to at the connector.
Disengage the wire insert as shown in the figure.
from the ribs.
CN122 Disconnect the CN900 as shown in the figure.
(Hereafter, disconnect connectors of identical Note on Reassembling (3) UL Tape (9 20mm)
f DB1-0948-000 (BLACK) l DA3-8809-000 (SILVER)
configuration in the same way.) CN900
4.5mm 4.0mm Insert the tweezers into the edge of the locked
M1.7
areas at the ends of the connector and disconnect
M1.7 these areas one at a time.
(SELF TAP) Fix the LCD Wire with the
CN103 UL Tape at the illustrated
m DB1-0947-000 (BLACK)
UL Tape position. Should not
3.5mm (9 20mm) overlap the marking-off line.
M1.7
Do not pull the cable as
CN900
it may break. Marking-off line LCD Wire
Insulating Tape (9 30mm)
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Note 2
j
Mic Wire
CN781
(1)
CN781
j DB1-6041-000 (SILVER)
Fasten the screws with the Front Cover Ass'y pressed to the arrow direction.
CN1701 4.5mm
Treat the Mic Wire as shown in the figure.
M1.7
SELF LOCK SCREW
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(1)
h
(1)
Top Heatsink Sheet
Step 1
Push in the ribs.
(2)
Rib
h DB1-6040-000 (SILVER)
2.5mm
M1.7
SELF LOCK SCREW
UL Tape (9 20mm)
j DB1-6041-000 (SILVER)
The Top Heatsink Sheet should be
4.5mm Rib pressed right down.
M1.7
SELF LOCK SCREW Insert two ribs and secure the unit with UL Tape.
10
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
1-10: Separation of MAIN-HANDLE FPC (XA25, XA20 only) and MAIN-ACC FPC (VIXIA HF G30, LEGRIA HF G30 only)
(1) Remove two screws (n2), disconnect the CN1901, and then detach the MAIN-HANDLE FPC (XA25, XA20 only) and MAIN-ACC FPC (VIXIA HF G30, LEGRIA HF G30 only).
(2) Remove two screws (o2) and detach the Raar Base Plate while disengaging the FPC.
<Note on Reassembling>
(1) Attach the Raar Base Plate as shown in the figure.
MAIN-HANDLE FPC
(XA25, XA20 only)
n
MAIN-ACC FPC
(VIXIA HF G30, LEGRIA HF G30 only)
(1)
(2)
(1)
CN1901
Flexible cable
Dowel
n DB1-2575-000 (SILVER)
Pass the Rear Base Plate under
3.0mm the flexible cable and engage
M1.7 it with the dowel.
WITH WASHER
5.0mm
Fold the flexible cable
M1.7 to the back side.
(SELF TAP)
11
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
1-11: Separation of Color View Finder Ass'y 1-12: Separation of Rear Cover Ass'y
(1) Remove one screw (h1), disconnect the CN1501, and then detach the Color View Finder (1) Remove two screws (m2), disconnect the CN1802, and then detach the Rear Cover Ass'y.
Ass'y FPC. <Note on Reassembling>
Note: The screw h is not reusable. When removed, use a new service part. (1) Attach the Rear Cover Ass'y as shown in the figure.
(2) Draw out the CVF, remove four screws (d2, i2), and then detach the Color View Finder
Ass'y.
(3) Detach the CVF Eye Cup.
<Note on Reassembling>
(1) Attach the Color View Finder Ass'y as shown in the figure. CVF Eye Cup
d DB1-6045-000 (BLACK) h d
5.5mm (1) Color View Finder
Ass'y
M1.7 Rear Cover Ass'y
(2)
h DB1-6040-000 (SILVER)
2.5mm
M1.7
SELF LOCK SCREW (3)
(1)
i XA4-9170-407 (SILVER)
(2)
4.0mm (1)
M1.7 (2)
(SELF TAP) i
(1)
CN1802
(2)
(1) Note on Reassembling (1)
CN1501
Rear Cover Ass'y
Note on Reassembling (1)
m
Color View Finder Ass'y
Flexible cable
Slide
12
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
DC PCB
DC Wire
Step 1
Connect the DC Wire2 and DC FPC CN2821
(2) CN1862 to the connector of the DC PCB. DC FPC
CN1861 (2)
j DC PCB
CN2821
(2)
Note 2
DC Wire (1)
DC FPC CN1802
DC FPC
DC Wire
CN1802
(1) DC PCB
Pass through the gap
Disconnect from the front side CN1800
with the standing wall.
of the connector. CN1801 Either
CN1800
connector
(1) can be
CN1801 connected to.
DC FPC
DB1-6041-000 (SILVER)
j 4.5mm DC Wire
M1.7 Step 2
SELF LOCK SCREW Attach the DC PCB and connect the connector of the MAIN PCB.
13
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
CN701 (1)
SDI Wire
AF SENSOR FPC
MIC JACK FPC
L Jack Unit
(1)
CN782 CN1700
Bottom Side
CN2800 Disengage from
(B to B) j the groove. Note on Reassembling (2)
j
Insert under the rib.
SDI Wire
(1) MIC JACK FPC
CN2801
(1) CN782
j
(1)
j DB1-6041-000 (SILVER)
4.5mm j
M1.7
SELF LOCK SCREW CN701
CN1700
14
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Attachment
reference
o
SDI Jack Ass'y
o (1)
SDI Holder Sheet
(XA25 only)
(6) (1)
h DB1-6040-000 (SILVER)
2.5mm
M1.7
SELF LOCK SCREW
EMI Wire Sheet (1)
(XA25 only) SDI Wire SDI Jack Ass'y
(XA25 only) (XA25 only)
i XA4-9170-407 (SILVER) o XA4-9170-507 (SILVER) (3)
EMI Wire Sheet
Wrap around the
4.0mm 5.0mm
(XA25 only)
SDI Gasket i
SDI Wire SDI Wire. M1.7 M1.7
(SELF TAP) (SELF TAP)
15
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Note
AF Screw
AF Sensor Ass'y
Lens section
p AF Sensor Ass'y
(1) AF Screw
Lens face
16
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
17
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(1)
j
m DB1-0947-000 (BLACK)
Pass through
3.5mm the Opening.
M1.7
m
Take care not to pinch
the flexible cable.
o XA4-9170-507 (SILVER)
5.0mm m o
M1.7
(SELF TAP)
18
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
o CN4200
Card Holder Ass'y Card Holder
(1)
Cushion
19
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Note 2: The screw h is not reusable. When removed, use a new service part.
(1) Peel off the UL Tape, disconnect the CN170, remove one screw (q1), detach the LCD Wire and then detach the Custom Dial Ass'y.
R Card Frame
(2) Remove three screws (o2,q1) and detach the R Frame and Right Cover Bottom Key.
(3) Remove three screws (h3) and detach the LCD OPEN FPC ASS'Y.
Pass the IR Knob through.
(4) Open the Card Lib, remove three screws (i2, q1), and then detach the R Card Frame while disengaging the IR Knob and Card Open Wire.
(5) Remove one screw (h1), disconnect the CN120, and then detach the CARD OPEN PCB and Card Open Wire.
<Note on Reassembling> CARD OPEN PCB
(1) Attach the CARD OPEN PCB and Card Open Wire as shown in the figure. Card Lib
Engage with the cutout section.
(2) Attach the LCD OPEN FPC ASS'Y as shown in the figure. Open the Card Lib and attach the R Card
(3) Attach the R Frame as shown in the figure. Frame, CARD OPEN PCB, and Card
Card Open Wire Open Wire as a unit.
(4) Attach the Custom Dial Ass'y and UL Tape as shown in the figure.
Note on Reassembling (2) Note on Reassembling (3)
<Instruction for Supply>
R Card Frame LCD Place the R Frame inside.
UL Tape (DY9-3032-000) R Frame
i (Opening/closing SW) Hinge Base Plate
CN120 (4)
(4) IR Knob
h
(5) (4)
(5)
q
h DB1-6040-000 (SILVER)
o XA4-9170-507 (SILVER)
UL Tape (9 20mm)
Note on Reassembling (4) Align with the end of the sheet metal.
Attachment reference
(3) (1) Custom Dial Ass'y
5.0mm Align with the end
(2) of the sheet metal.
M1.7 o h LCD Wire
Right Cover Ass'y
(SELF TAP) (2) h Right Cover Attachment
(3) Bottom Key reference
q XA4-9170-607 (SILVER) (1) (Opening/closing SW)
q (3) Rib Dowels LCD Wire
6.0mm
(1)
h
M1.7
q (1) CN170 (3)
CN170
(SELF TAP) Engage with the two dowels and UL Tape (9 17mm)
Custom Dial Ass'y (1) Engage with the
LCD OPEN FPC ASS'Y put the rib in Right Cover Ass'y. cutout section. CUSTOM DIAL FPC
20
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
i XA4-9170-407 (SILVER)
Sucker
4.0mm
Lift the panel with a Sucker and Claws B M1.7
remove the LCD Top Cover Ass'y
(SELF TAP)
through the gap.
LCD Top Cover Ass'y
21
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Claw
LCD Cushion
(Double Sided Tape side
LCD PCB O-EL Display
should be positioned on top.) Touch Panel flexible cable
(2) (2) Panel O-EL Display Panel
Step 1 LCD Cushion
CN902 3. Displace the Touch Panel flexible Step 2 Push the O-EL Display Panel against Step 3 The two concave sections of
(1) cable, press the concave section the dowels and inside of the Bottom the LCD Cushion must match
CN4501 of the LCD Cushion against the Cover, engage the two dowels, and the two end surfaces shown in
Claw
two dowels, and engage the two dowels. press the O-EL Display Panel against the figure and they must be
Claw the LCD Cushion. fully pushed down.
(1) LCD PCB
(2) Insert
(1)
o LCD KEY FPC ASS'Y LCD Frame CN902
r
(1) (1) o XA4-9170-507 (SILVER)
CN903 Dowel
5.0mm
M1.7 Dowel
(SELF TAP)
Dowels
r XA9-1151-000 (SILVER) Claw 4. Insert the LCD KEY FPC ASS'Y into
2.0mm the four dowels and pass the flexible
Claw cable through the hole. Engage the CN903 CN4501
M1.7
(NK GRIP) Dowels three claws and attach the LCD
LCD KEY FPC ASS'Y Frame and LCD PCB as a unit. 5. Connect the CN902, CN903 and CN4501.
22
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Lens Ring
Lens Ass'y
23
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(1) Attach the Handle Top Cover as shown in the figure. (1) Hanal FL-778
(DY9-3026-010)
(2) Attach the Handle Rear Connector Ass'y as shown in the figure.
(3) Attach the Handle Rear Connector section as shown in the figure.
q XA4-9170-607 (SILVER) u XB1-1300-609 (BLACK) Rear Connector Cushion
<Instruction for Supply> Handle Top Cover section
6.0mm (Detach from the Rear side)
6.0mm
Rear Connector Cushion : Hanarl FL-778 (DY9-3026-010) Rear Connector Screw
M1.7 M3.0
(SELF TAP)
Note on Reassembling (1) u Rear Connector
s DA3-8808-000 (BLACK) v XA9-1895-000 (BLACK)
(5) Cushion
M1.7
(5)
Rib
Note on Reassembling (2) t Handle Rear
Connector Ass'y
Rear Connector Screw
(5)
Connect the CN5300, engage the
screw holes and rib, and attach the v (3)
Handle Top Cover section.
CN5300 Rear Connector
v (5) q
(3)
Cushion
Handle Rear
Note on Reassembling (3) Screw
Dowels
Handle Rear
Push inward to
v (3)
Screw
reach the
Handle Rear deepest position. Handle Rear
Screw (2)
Step 2 Handle Rear Screw (2)
1.5mm
Plate
Handle Rear Step 3
Step 1 Connector Step 1
section Handle Rear s
Connector Ass'y Step 2
Step 2 Step 1 Handle Rear Cover
Step 3 Attach the Handle Rear
Connector Ass'y in the direction Handle Rear
q Be careful not to mistake the screw hole. shown in the figure. Connector section
24
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
(5) Remove four screws (o4), and then detach the Shoe Base Frame and Handle Top Frame. (1) (1)
(6) Remove two screws (o2), and then detach the Handle Frame.
<Note on Reassembling>
(1) Attach the Trigger Cushion as shown in the figure.
(2) Attach the XLR Knob Cushion as shown in the figure.
(3) Attach the XLR AUDIO FPC and Shoe Base Frame Sheet as shown in the figure.
XLR AUDIO FPC
Shoe Base
e DB1-0420-000 (BLACK) o XA4-9170-507 (SILVER) q XA4-9170-607 (SILVER)
Frame Sheet
4.5mm
q
5.0mm 6.0mm
M1.7 M1.7
o
M1.7 (4)
(NK GRIP) (SELF TAP) (4) (5)
(SELF TAP) (4)
XLR MICOM PCB (5)
Note on Reassembling (1) Note on Reassembling (3)
HANDLE REAR XLR POWER o
Trigger Cushion Shoe Base End of the sheet metal FPC (2)
Frame Sheet Attachment
CONNECTER FPC o
XLR MICOM PCB XLR AUDIO FPC reference:1mm XLR POWER (4) Shoe Base
(3)
PCB (2) CN622 Frame
CN620
No protrusion CN600
is allowed. Trigger
(3) CN601 Cushion (4) (5)
Swich Attachment
reference:1mm
(3)
Attach the both sides of the Trigger Cushion so End of the Shoe Base Frame
as to prevent it from pushing the switch. sheet metal o
CN622
Note on Reassembling (2) (6) Handle Top Frame
(6)
25
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
CN5471
(1) (2)
o LED
(1)
26
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
XLR Frame
(1) (4)
Switch
XLR Knob Cushion 3 XLR Knob Cushion
27
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
Handle Screw
Rear Washer Handle Rear
Screw
Handle Screw
Rear Cushion Front Screw Handle Rear
Cover Screw
Handle Front
Shoe Plate Handle Lock
(1) (3)
Spring
(3)
Handle Rear
Screw Handle Lock (3)
Pin
Chamfered part (3)
With the Handle Screw Rear Cushion directed Handle Lock
as shown in the figure, insert in the Handle Rear Screw. Guide Handle Screw
Handle Front Screw Section Handle Screw
Rear Washer
Rear Washer
Handle Front
Screw Sleeve
(2) Handle Screw Rear Cushion
Handle Lock
Spring Handle Front
Ring
Handle Lock
Pin
Handle Front (2)
Handle Lock Shoe Plate (1) Handle Front
Guide Shoe Plate
28
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 DISASSEMBLING
a DB1-6208-000 (BLACK) b DB1-6044-000 (BLACK) c DA3-8806-000 (BLACK) d DB1-6045-000 (BLACK) e DB1-0420-000 (BLACK) f DB1-0948-000 (BLACK) g DA3-8804-000 (BLACK)
h DB1-6040-000 (SILVER) i XA4-9170-407 (SILVER) j DB1-6041-000 (SILVER) k DB1-6043-000 (SILVER) l DA3-8809-000 (SILVER) m DB1-0947-000 (BLACK) n DB1-2575-000 (SILVER)
o XA4-9170-507 (SILVER) p DB1-1072-000 (SILVER) q XA4-9170-607 (SILVER) r XA9-1151-000 (SILVER) s DA3-8808-000 (BLACK) t DB1-2682-000 (BLACK) u XB1-1300-609 (BLACK)
29
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 SERVICE HINT
CONTENTS
1: Current Consumption................................................................................................................................................................................... 2
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 SERVICE HINT
1: Current Consumption
The following table shows the actual measured value of current consumption in each state.
Measuring conditions: Product state, panel (Brightness: Standard), AVCHD 24Mbps, Frame rate (59.94P/50.00P),
SD CARD (SDHC 32GB)
Preset voltage: 7.4V (BATT terminal)
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 SERVICE HINT
* Since nonconformance to the standard is considered to be caused by an adjustment error, perform R-Y R-Y
adjustment again.
B-Y B-Y
8mm
8mm
3
Service Manual XA25, XA20, VIXIA HF G30, LEGRIA HF G30 CHARTS
CONTENTS
1: IS Adjustment Chart.....................................................................................................................................................................................2
2: CZ Chart.......................................................................................................................................................................................................3
IS adjustment chart
4.03
AF SENSOR LINEARITY
CHART 2900mm (LEFT)
AF SENSOR LINEARITY
CHART 2900mm (RIGHT)
AF SENSOR LINEARITY
CHART 800mm