Professional Documents
Culture Documents
L02-Model
* When speed is more than 40 mm/s and/or strokes longer than 350mm, check STROKE SETUP section.
** For 12 Vdc power supply currents are doubled and loads are 20% lower.
BEFORE OPERATING ACTUATOR MAKE SURE YOU READ AND UNDERSTOOD BASIC OPERATIONAL INSTRUCTIONS SHOWN ON
USERMANUALS, AVAILABLE FROM WEBSITE.
THIS DOCUMENT DISPLAYS MOST TYPICAL STANDARD FEATURES AND SETUPS: CONTACT OUR OFFICES FOR MORE.
57
L02 Version without limitswitches
Ø36
20
8
20 172 15 Ø48
+0.1 +0.1
Ø10 0 Ø10 0
Ø25
25
13 B + stroke 10
DIMENSION Stroke < to 320 mm. Stroke > to 320 mm.
B1 + stroke
Encoder Version B 228 + stroke 239 + stroke
B1 257 + stroke 268 + stroke
58
L02
STROKE SETUP: Useful tips for handling stroke and avoid run-on-block collision.
When stroke is more than 350 mm, Total stroke,to be stated in ordering-key.
add 50 mm extra-stroke as guidance,
and put corresponding value in ordering-key. Extra stroke gap Available workout stroke Extra stroke gap
FULL SPEED
RAMP-UP SLOW
SPEED DOWN
* *
WARNING: STROKE
SPEED-TIMING ALONG STROKELENGHT:
ramps are extremely important with high speed !!! Inverter or PWM drive recommended!
* The more speed raises the more extra stroke has to raise too.
BUCKLING: When stroke is longer than 500mm, BUCKLING can be a risk: please check mounting with our offices and/or see user-
manuals.
LOAD
Stroke longer
than 500-600
mm IMPORTANT:
BUCKLING
MOMENTUM Long strokes, even if load is low, can generate
significant buckling momentums, as sketch
slows.
This happens when actuator is in its all-opened
position: that’s the reason why we recommend
100 mm extra-stroke.
Pushtube will have this100 mm-portion always
inside the overtube, improving guidance against
buckling.
For more information on this, contact our office.
59
ORDERING KEY
L02 / 0250 / M01 / 24 / 2FCM0 / E10 / P1 / A1
MODEL:
L02 L02-FCM L02-VRS
STROKE:
es. 250 mm = 0250
min 50; with 50 as incremental
VERSION: (Pag. 57)
M00 = Not standard speed
MOTOR: (Pag. ACCESSORIES) +0.1 +0.1 +0.1 +0.1
12 = 12 Vdc Ø10 0 Ø10 0 Ø10 0 Ø12 0
Ø25
Ø25
24 = 24 Vdc
LIMIT SWITCHES: (Pag. ACCESSORIES)
25
25
None: Leave blank
ENCODER : (Pag. ACCESSORIES)
13 B = 228 + corsa/stroke 10 13 B = 239 + corsa/stroke 10
E10: Encoder 1 channel 4 ppr NPN (open Collector)
REAR END:
6
6
P1 = Yoke (standard)
8
P2 = Special (provide drawing)
20
20
8
8
FRONT END:
A1 = Eyelet (Std pag.58) 27
6
24
6
27
A3 = Yoke + Clip A1 = OCCHIO (STANDARD) A2 = FORCELLA FISSA
A4 = Rod end A1 = EYELET (STANDARD) A2 = YOKE
A7 = M10 male
+0.1 +0.1
Ø10 0 Ø10 0 Ø10 H7
NOTE: COMPLETE THE ORDERING KEY ADDING THE OPTIONSØ10YOU
H8 CAN FIND IN THE “ACCESSORIES AND OPTIONS” SECTION
Ø30
20
10.5
6
20
6
10
14
20
20
8
8
6
27 20 27
6
A3 = FORCELLA CON CLIP DIN 71752 / UNI 1676 A4 = TESTA A SNODO DIN 648 serie K / UNI 6126
A3 = YOKE WITH CLIP DIN 71752 / UNI 1676 A4 = ROD END DIN 648 serie K / UNI 6126
+0.1 +0.1
+0.1
Ø10 Ø10 +0.1
0 Ø10 0 Ø
0 Ø10 0
Ø25
M10
15
M10
25
25
P2
25
P1 13 B = 228 + corsa/stroke 10 13
13 B = 237 + corsa/stroke 13 B = 237 + corsa/stroke 32
66
6
“FCM” MAGNETIC
6
LIMITSWITCHES
20
20
88
20
8
20
Ch.19
27
66
Ch.19
6
27 27
6
20Ø25
25
25
A4
13 B = 228 + corsa/stroke 10 13 13 B B= =290
239+ +corsa/stroke
corsa/stroke 1210 13
A3
6
A7
6
820
6
10
A1
20
20
8
20
20
8
27 27
6
2024
6
27
6
15
20
Note: With encoder, dimension13 “B” is 30 mmBlonger = 290 + corsa/stroke 12 13 B = 294 + corsa/stroke 15
13
L02 = See pictures 13 B = 237 + corsa/stroke
10.5
20
66
10
14
L02-FCM = + 34 mm
20
20
20
8
8
88
20
27 27
66
27
L02-VRS = + 40 mm A3 = FORCELLA CON CLIP DIN 71752 / UNI 1676 A4
A5 =
= TESTA A FEMMINA
FILETTO SNODO DIN 648 serie K / UNI 6126
M10 A7 = FILETTO MASCH
Bellows + 20mm ( noA3for= versions
YOKE WITH CLIP DIN 71752 / UNI 1676
FCM ) A4
A5 =
= ROD FEMALE
M10 END DIN 648 serie K / UNI 6126 A7 = M10 MALE
+0.1 +0.1
60 Ø10 0 Ø10 0
M10
15
M10
60
25