Professional Documents
Culture Documents
UDC 669.14.018.4.018.8 – 41
BS 1449-2:1983
This British Standard was published under the direction of the Iron and Steel
Standards Committee ISM/-. Its preparation was entrusted to Technical
Committee ISM/10 upon which the following bodies were represented:
The following bodies were also represented in the drafting of the standard,
through subcommittees and panels:
© BSI 09-1999
Contents
Page
Committees responsible Inside front cover
Foreword ii
Section 1. General requirements
1.1 Scope 1
1.2 Definitions 1
1.3 General 1
1.4 Information to be supplied by the purchaser 1
1.5 Steelmaking process 3
Licensed Copy: Giorgio Cavalieri, ALSTOM, 2-Mar-01, Uncontrolled Copy. © BSI
© BSI 09-1999 i
BS 1449-2:1983
Foreword
This Part of BS 1449, prepared under the direction of the Iron and Steel
Standards Committee, is a revision of BS 1449-2:1975 which is withdrawn.
It constitutes a general updating of the requirements for stainless and
heat-resisting steels, in line with moves towards international harmonization of
these materials.
Included for the first time are definitions, based on those agreed internationally,
for the terms used and, additionally, a clause for the identification and marking
of the material. The tabular presentation of the specific requirements for
particular steel grades has been simplified.
The other Part of this standard is:
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 8, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on the
inside front cover.
ii © BSI 09-1999
BS 1449-2:1983
1)
Information regarding manipulation, finishing or ultimate service conditions to which the material will be subjected is of
assistance to the manufacturer in order that the most suitable material is supplied.
© BSI 09-1999 1
BS 1449-2:1983
c) the condition in which the steel is to be f) the condition in which the material is to be
supplied, if the softened condition is not required; tested if tests are required in a condition
d) the nominal dimensions and quantity of the other than the delivery condition [see item c)],
product required; e.g. BS 1449-2, steel 310S24,
plate, 6 m × 2 m × 8 mm, 24 off, surface
e) the surface finish required for each face of the
finish no. 1.
material (see 1.7.2 and Table 1);
Table 1 — Surface finishes
Finish No. Description Notes
2 © BSI 09-1999
BS 1449-2:1983
be used in making the steel and the ordered product the impossibility of rejecting portions of the coil. This should be
(see 1.5). taken into account by the purchaser in his assessment of the coil.
© BSI 09-1999 3
BS 1449-2:1983
1.9.2.2 Flat form. The flat product shall be supplied 1.11 Testing and manufacturer’s
with sheared or rotary sheared edges, unless a certificate
special edge condition is specified on the enquiry
and order. 1.11.1 General. The manufacturer shall carry out
tests to ensure that the material complies with the
NOTE Special edge conditions, e.g. as-rolled edges, rolled round
edges, slit and deburred edges, may be available for certain relevant requirements of this specification and to
products. enable him to provide a test certificate in accordance
with the order. When a certificate is required, the
1.10 Chemical composition order shall state:
1.10.1 Cast analysis. The chemical composition of a) that a certificate is required;
4 © BSI 09-1999
BS 1449-2:1983
Products manufactured in The batch of pieces from the same Piece length u 15 m 1 test
the flat form, heat treated cast and within 10 % of the same sample
Piece mass u 3 000 kg
in batches or in continuous nominal thickness, treated together
furnaces as one heat treatment batch or heat Piece length > 15 m 2 samples,
treated to the same procedure as a or Piece mass > 3 000 kg one from
production run of up to 40 pieces each end
of a long,
Licensed Copy: Giorgio Cavalieri, ALSTOM, 2-Mar-01, Uncontrolled Copy. © BSI
© BSI 09-1999 5
BS 1449-2:1983
% % % % % % % % % % %
309S24 Cr Ni 23/14 — 0.15 1.00 — 2.00 0.045 0.030 22.0 25.0 13.0 16.0
310S24 Cr Ni 24/20 — 0.15 1.00 — 2.00 0.045 0.030 23.0 26.0 19.0 22.0
6 © BSI 09-1999
BS 1449-2:1983
1 N/mm2 = MPa
a
Elongation measured on flat test pieces using 50 mm gauge length or 5.65ÆSo. For cylindrical test pieces, a gauge length
of 5.65ÆSo is used.
b
For items of adequate thickness the Brinell hardness test may be used, applying the same limiting HB hardness values as given
for HV.
c
See 1.8
© BSI 09-1999 7
Licensed Copy: Giorgio Cavalieri, ALSTOM, 2-Mar-01, Uncontrolled Copy. © BSI
blank
8
BS 1449-2:1983
Publications referred to
© BSI 09-1999
BS 1449-2:
1983
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
Information on standards
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the internationalstandardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
written permission of BSI must be obtained.