Professional Documents
Culture Documents
Addressable Fire
Control Panels
Installer Manual
www.fireclass.net
This Fire Control panel can be programmed only using
the Software FireClass500 Console release 2.0 or hi-
gher. 0051
Control panel FW ver. 2.0 or higher. Tyco Fire & Security GmbH
TYCO shall not assume the responsibility for damage ari- Victor von Bruns-Strasse 21
sing from improper application or use. This Fire Control 8212 Neuhausen am Rheinfall
Switzerland
panel has been designed and manufactured to the hi- 09
ghest standards of quality and performance. DoP-2015-4212 (FC510)
Installation of this Control panel must be carried out DoP-2015-4213 (FC520)
strictly in accordance with the instructions described in EN 54-2:1997+A1:2006 EN54-4: 1997+A1:2002+A2:2006
this manual, and in compliance with the local laws and Control and indicating equipment with integrated power supply
bylaws in force equipment for fire detection and fire alarm systems for buildings.
The FC510 and FC520 Fire Control panels comply with EXPECTED OPTIONS
the essential requirements of standards EN54-2; Fault signals from points
EN54-4. Dependencies on more than one alarm signal: type A and B
Delays to outputs
Recycling information Disablement of addressable point
The manufacter recommends that customers dispose of their used equip- Test condition
ments (panels, detectors, sirens, and other devices) in an environmentally Output to fire alarm device
sound manner. Potential methods include reuse of parts or whole pro- EN 54-2 ESSENTIAL CHARACTERISTICS
ducts and recycling of products, components, and/or materials. Performance under fire conditions Passed
Response delay (response time to fire) Passed
Waste Electrical and Electronic Equipment (WEEE) Di- Operational reliability Passed
Durability of operational reliability, Temperature resistance Passed
rective
Durability of operational reliability, Vibration resistance Passed
Durability of operational reliability, Electrical stability Passed
Durability of operational reliability, humidity resistance Passed
In the European Union, this label indicates that this product EN 54-4 ESSENTIAL CHARACTERISTICS
should NOT be disposed of with household waste. It should be depo- Performance of power supply Passed
sited at an appropriate facility to enable recovery and recycling. Operational reliability Passed
Durability of operational reliability, Temperature resistance Passed
NOTE- The series FC500 Fire control panel can support several ad- Durability of operational reliability, Vibration resistance Passed
dressable devices (Detectors, Modules, Manual call Points, etc). The Durability of operational reliability, Electrical stability Passed
present manual includes the instructions for their programming, but Durability of operational reliability, humidity resistance Passed
for further informations on those devices and their accessories, plea-
se visits: www.fireclass.net.
INTRODUCTION 5 PC PROGRAMMING 29
FC500 Fire Contro Panel 5 Introduction 29
Accessory Items 5 Installation 29
Description 5 Select language 29
Input 5 Software window Look 29
Outputs 5 Control panel connections 29
Operating Features 6 Main window 29
Interface 8 Icons description 30
Access to Signalling and Commands 8 File 30
Power Supply 8 Communication 31
Options 31
Database 31
PARTS IDENTIFICATION 9 Mode setup 31
The status LED 9 Help 31
Description of Parts 14 Devices programming 31
LEDs and KEYs Labels 17 Description of the icons in the tool bar. 31
Description of the Control keys 18 Parameters detectors programming 32
Input modules programming 33
Output modules programming 33
Multiple Input-Output Module - Programming
INSTALLATION 19 Parameters (FC410MIO) 33
Installing accessory boards 19 Manual Call Point programming parameters 34
Installing the Control panel 19 Zones programming 34
Installing FC500REP Repeaters 19 Outputs Programming 34
Installing the FC500PS e FC500IP board 19 NAC1, NAC2 and NAC3 Outputs 34
Installing the FC500 Slave control panel 19 OS1....OS8 Outputs 35
Description of the Terminals 20 O9....O16 Outputs 35
Main Board terminals 20 General Options programming 35
The System Wiring 21 PSTN interface 36
Connecting Addressable Analogue Devices 21 IP interface 37
Connecting Conventional Devices 22 CLOCK 37
Connecting Repeater and Slave Control panel LOG 37
23 Battery Calculation 37
Connecting Output Devices 23 Loop Wiring calculation 37
Bell Outputs 23 User mode 40
Connecting a Power Supply 24
Thermal Probe 25
Installing the 38Ah battery metal Box 27
Maintenance 27
PROGRAMMING FROM THE PANEL 41 FC430SAB/SAM - Sounder Base Address
Using the system 41 Modules 55
L1= First Level: this level allows the Reading FC430SB - Loop Low Power Sounder Base 55
Parameters ONLY: 41 4B-I - Isolator Base 56
L2= Second Level or USER Level: access to this FC490ST - Loop Service Tool 56
level requires entry of the USER PIN (Access Level FC410BDM - Beam Detector Module 56
2). 41 FC410CIM - Contact Input Module 56
L3= Third Level or INSTALLER Level: access to FC410DIM - Detector Input Module 56
this level requires entry of the INSTALLER PIN FC410RIM - Relay Interface Module 56
(Access Level 3). 41 FC400CH - Addressable Carbon Monoxide + Heat
Operating the system 41 Detector 56
Main Page - Accessing the system 42 801RIL - Remote LED Indicator 56
Insert password 43 801HL - Remote LED Indicator 56
Programming Page 44 HVR800-High Voltage Relay 56
1 KEY- Auto Enrolling (Autolearning 44 MP69-Duct Probe Unit 57
Warning Enrolling (Autolearning) 44 FIRERAY 50-Optical Beam Smoke Detector 57
0 KEY - insert-Modify password 45 FC410LPSY and FC410LPAV loop powered
9 KEY- Restore Default 46 sounders and sounder-beacons 57
KEY 2 -Device 46 FC430LPSB and FC430LPASB Loop Powered
KEY 3- SW zone 47 Addressable Sounder/Beacon Base 57
Detector alarm verification (Smoke delay) 47 FC410SNM Sounder Notification Module 57
4 KEY- OUTPUT 48 FC410TSM – door control module 57
Choose Output 48 FC410DDM – Universal fire and gas detector
NAC active on disablements 48 module 57
5 Key- Network 49 FC410QIO Quad input output module 58
FC500-MFI programming Procedure 49 FC410QRM Quad relay module 58
KEY 6-TELECOM 50 FC410LPBS-R/W loop powered sounders and
KEY 7-OPTIONS 50 sounder-beacons (EN54-23) 58
KEY 8-SYSTEM 51 FC430LPBSB Loop Powered Addressable
FC500REP Repeater Address Sounder/Beacon Base (EN54-23) 58
from the Repeater panel ONLY 51
NETWORK Configuration 51
QUICK GUIDE 59
Technical features 59
QUICK START-UP PROCEDURE 52 Description of the terminals 59
PROCEDURE 52
Detectors 52
Modules 52
Zones 53
Panel outputs 53
Conventional zone 53
Panel general option 53
ACCESSORY 54
FC500IP - IP Module 54
FC500PSTN - Telecom Module 54
4B - Universal Base 54
FC400H or FC460H - Addressable Heat Detector 54
FC400P or FC460P - Addressable Optical
Smoke 54
FC400PH or FC460PH - Addressable Optical
Smoke & Heat Detector 54
FC410LI - Line Isolator Module 55
FC410MIM - Mini Input Module 55
FC410MIO - Small Addressable Multi I/0 Module 55
FC410SIO - Single Input/Output Module 55
FC420CP - Addressable Break Glass Callpoint
(indoor) 55
FC421CP - Addressable Break Glass Callpoint
(outdoor) 55
INTRODUCTION
In this manual we will use the term FC500 control panel FC500REP This Repeater panel is intended for con-
to indicate the common features of Fire control panel. nection (via 4 wires) to FC500 Control panels. It provi-
Otherwise we will use the specific terms. des all the visual and audible warnings generated by
the Control panel and allows end-users to manage the
FC500 Fire control panel is avalaible in the following system from a remote location (up to 1000 m, with dou-
models: ble twist shielded cable).
Ø FC510 - Analogue addressable Fire Control Panel The FC500 "Master" Control panels can support up to
with one not expandable Loop and with Switching (8) eight FC500REP Repeater panels.
Power supply 5,5 A;
Ø FC520 - Analogue addressable Fire Control Panel FC500 Slave The FC500 "Master" Control panels can
with two not expandable Loops and with Switching support up to (7) seven FC500 Slave Control panels.
Power supply 5,5 A; These Control Panels can be used to expand the
FC500 system, in modular way.
+ The components of these Control panels operate
as intended when the external ambient conditions Software FireClass500 Console This user-friendly
comply with the requirements of class EN software application (Windows) offers a quick and easy
60721-3-3:1995. way to program the Control panel and provides event
log functions.
The Loops of FC500 control panel provide the follo-
wing features:
Ø max 250 analogue devices. Description
Ø The conventional line of the FC500 contro Panel can
support up to 30 devices. n Input
In any case, FC500 Fire control panel cannot sup- 250 devices max every Loop
port more than 2000 devices (500 devices for every
couple of Loop) (up to 2000 m (Loop) with shielded 30 devices max on the conventional line
cable 2x2.5).
The FC500 control panel must be powered by n Outputs
BAQ140T24 (27,6 V - 5,5 A ) switching power supply. This section describes how the Control panel outputs
operate.
Moreover all FC500 models provide housing for an LCD
module with 40 characters for line and 4 lines backlit, Supervised outputs The Control panel will be able to
which provides written information regarding the detect and signal short-circuits and power supply inter-
system status and for programming the control panel. ruptions on this type of output.
INTRODUCTION 5
n Operating Features During Silence status (Silence LED glowing), it is pos-
sible to use the Silence key to release the Silenceable
Warning The FC500 control panel can be program- outputs, and the Reset key to restore standby status.
med to provide WARNINGS or PREALARMS status be-
fore ALARM status.
This status will be signalled by the WARNING display.
+ IfLED
the Control panel is in Night Mode (Day Mode
OFF), the Control panel will exit Silence sta-
The panel will generate a warning when an input point tus when the programmed Night mode Silence
(detector) exceeds its warning threshold and there is time expires
risk of an alarm.
Day/Night Mode The control panel can operate in
-WARNING STATUS will be signalled by: DAY or NIGHT Mode. See "PC PROGRAMMING"
Ø a screen on LCD display chapter.
Ø the WARNING output points if the Pre-alarm option If the system is silenced during DAY Mode, SILENCE
is enabled; status will be held until the system is unsilenced (i.e. un-
less new alarms). If the system is silenced during
Pre-alarm If a zone generates an alarm during Day NIGHT Mode, SILENCE status will be held until the
Mode, the Control panel will start the Pre-alarm Time. Night Mode Silence time expires.
This status will be signalled by: On power up (at default) the system will set to DAY
Ø a slow intermittent beep;
Mode. During this operating mode, silenced alarms/fa-
Ø glowing on the Pre-al. LED; ults will not be unsilenced automatically until the Night
Ø a screen on LCD display
Mode Silence time expires.
Ø Activation of respective outputs , if the Pre-alarm
option is enabled;
Fault This Control panel can detect and signal the
+ This
Faults shown in the Table n.1:
Control panel will generate an Instant Alarm if
alarm conditions are detected during Night Mode
Fault conditions will be signalled by:
or if an alarm is triggered from a Callpoint.
Ø a slow intermittent beep (at 1 second intervals);
Ø glowing on the Fault LED and on relative Fault LED;
During Pre-alarm status, you will be able to:
Ø a screen on LCD display;
Ø activate an Evacuation Alarm by pressing and hol-
Ø activation of the Fault output;
ding the Evacuate Key (Access Level 1 — refer to
Ø activation of other programmed outputs;
“Access to signalling and commands”),
Ø slow blinking on the Fault LED.
Ø stop the Silenceable outputs and interrupt the
Pre-alarm Time by pressing the Silence key
The Fault output and other outputs (if duly program-
(Access Level 2).
med by your Installer) will restore to standby automati-
cally when fault conditions clear.
During Silence status (Silence LED glowing), it is pos- Under certain circumstances, fault conditions may clear
sible to use the Silence key to release the Silenceable spontaneously, if this occurs, the event will be stored in
outputs, or use the Reset key to restore standby status. the memory until the Control panel Resets.
+ IfControl
Stored Fault events will be signalled by:
the Control panel is operating in Night Mode, the Ø slow blinking on the Fault LED.
panel will exit Silence status automatically
when the programmed Night mode Silence time
expires.
Loop signal open Loop positive signal open Transistor NAC 2 "
Loop local short Local short on Loop controller Transistor NAC 3 "
Loop right short Right side Loop short Device not Device on the loop without
INTRODUCTION 7
Disabled This Control panel can disable: Access Level 2 (L2) Operating the system (PIN Code
the devices on the Loop (input and Output devices), entered): PIN Code Users can operate the system.
the bell outputs, the software zones; (User level)
the network devices (Repeaters or Slave control pa-
nels). Access Level 3 (L3) Programming and Opening the
Control panel (PIN Code entered): ONLY Qualified
DISABLED zones cannot generate alarms or warnings persons with authorization are allowed to open the
of any kind, and DISABLED outputs cannot be activa- Control panel door (requires removal of the screws) for
ted. maintenance purposes or replace batteries. (Installer
Level).
Disabled status will be signalled by:
Ø glowing on the Disabled LED; Access Level 4 Repairing or replacing the PCB:
ONLY the Manufacturer should be allowed to repair or
+ vel
Only when the control panel is at Level 2 or at Le-
3 can DISABLE zones and/or outputs.
replace the PCB, (requires removal of the screws).
n Power Supply
Reset Resetting the Control panel will restore the out- The power supply system of the FC500 Control panels
puts to standby status, clear the memory, and interrupt complies with EN54-4.
the power supply to terminals 24R. All models are powered by the Mains (110/230 V~,
60/50 Hz):
+ Only when the control panel is at Level 2 or at Le-
vel 3 can Reset the system.
Ø the FC510 model has Switching Power Supply which
supplies up to 5.5 A at 27.6 V;
Ø the FC520 model has Switching Power Supply which
n Interface supplies up to 5.5 A at 27.6 V;
All models can house two 12 V batteries which, when
Visual Signalling The system status will be signalled connected in series, will supply 24 V to the Control pa-
on the Control panel LEDs as follows: nel and peripherals in the event of black-out, and will
GREEN indicates normal operating conditions; also provide any pickup currents which exceed the ma-
AMBER indicates specific operating modes (for exam- ximum current supplied by the Switching Power Supply.
ple Day or Night mode), and/or Fault conditions;
RED indicates Alarm conditions. The FC510 and FC520 model can house two 12V 17 Ah
batteries (YUASA NP 17-12 FR model or similar — flame
Memory The Control panel will signal Fault events class UL94-V2 or higher).
(FAULT LED blinking) until the system Resets, even if
the event clears in the meantime.
+ Ifrequirements
necessary, (Full configured Loop or for particular
of the system) FC510 or FC520 con-
trol panel model can be connected to two 12V
Audible Signalling The Buzzer will signal the Control 38 Ah batteries in an external metal box (see Figu-
panel status as follows: re 16).
Status Sound Pause Description This Control panel can detect, signal and store in memory
Warning 2s 2s Slow Intermittent Beep the following power faults: shorted 24V or 24R outputs;
Low battery, Battery fault or Battery disconnected (Low
Prealarm 0,5 s 0,5 s Intermittent beep
Battery LED and No Battery LED), Ground fault (Earth
Alarm 0,2 s 0,2 s Fast Intermittent Beep LED) and Mains failure (Mains LED).
Fault 1s 1s Slow Intermittent Beep
Reset no sounds + The “No Battery or Low Battery” fault may be si-
gnalled with a delay up to 1 minute. The “Mains”
Test no sounds
(Amber) fault will be signalled when the program-
Table 2 Buzzer signalling med delay expires.
LEDs DESCRIPTION
FIRE Glowing indicates Alarm status. In the event of an Alarm, the Control panel will activate the
unbypassed alarm outputs.
More Alarms Glowing indicates more Alarm status.
Pre-alarms Blinking indicates Pre-alarm status.
Communicator Glowing indicates that transmission was successful.
(Red) Blinking indicates that transmission is in progress.
On display of control panel it is possible to know the connection type: PSTN, GSM, or LAN network.
FAULT Glowing indicates the presence of a Fault: the following LEDs or the screen on the display indicate
the type of the Fault. Slow blinking indicates a fault event in memory (Reset turns OFF ).
Logic Unit Glowing indicates a blocked Control panel. IMPORTANT: Maintenance required.
NOTE – When the Control panel is switched on for the first time, this LED will blink until a Reset has
been performed.
Lost Device Glowing indicates that a Loop device has disappeared (missing address).
Communicator Glowing indicates the Dialer has been disabled; Slow blinking indicates that the dialer has broken
(Amber) down
Nac Fire Glowing indicates that NAC FIRE Output is bypassable (disabled), Slow blinking indicates the
Output presence of a Fault on NAC FIRE Output.
Earth Glowing indicates a Voltage leakage to Earth.
IMPORTANT: Check wiring insulation
Low Battery Glowing indicates Batteries empty or faulty. If this condition persists, the batteries will be unable to
function as intended in the event of blackout, IMPORTANT: New batteries required.
NO Battery Glowing indicates Batteries empty or disconnected ; check if the connections are correct.
MAINS Glowing indicates Mains failure or Switching Power supply fault. During this condition, the Con-
(amber) trol panel will be powered by the batteries.
Day mode Glowing indicates that the Control panel is operating in Day Mode
OFF indicates that the Control panel is operating in Night Mode
Disabled Glowing indicates the Disabled status of any bypassable entity.
Silence Glowing indicates that Silenceable outputs have been forced to standby by means of SILENCE key;
in Day Mode the SILENCE will remain until the SILENCE key will not been pressed again,
while in Night Mode after the Silence Time expires automatically the SILENCE will end.
Test Glowing indicates Test conditions on at least one zone.
MAINS OFF indicates Mains failure.
(Green) IMPORTANT: Power must be restored before the batteries empty.
PARTS IDENTIFICATION 9
a) 5
1 1
F1
F2
FIRE
F3
FAULT
F4
LAMP
MORE ALARMS LOST DEVICE BUZZ
TEST
1 2 3
PRE-ALARM LOGIC UNIT
SILENCE
ABC DEF GHI
COMMUNICATOR COMMUNICATOR
INVESTIGATE
4 5 6
DAY MODE NAC FIRE OUTPUT
JKL MNO PQR
TEST NO BATTERY
ESC 0
MAINS MAINS
EVACUATE
FC500
3 1 4
Figure 1 Front view of the FC510, FC520 control panel (a), and of Repeater FC500REP (b)
2 1
2 3 1 5 2
b)
F1
F2
FIRE
F3
FAULT
F4
LAMP
MORE ALARMS LOST DEVICE BUZZ
1
TEST
1 2 3 1
PRE-ALARM LOGIC UNIT
SILENCE ABC DEF GHI
COMMUNICATOR COMMUNICATOR
INVESTIGATE 4 5 6
DAY MODE NAC FIRE OUTPUT
JKL MNO PQR
SILENCE
DISABLED HEARTH
BUZZER
7 8 9
SILENCE LOW BATTERY ESC
MIC RESET STU VWX YZ
NO BATTERY
TEST
EVACUATE
ESC 0
MAINS MAINS FC500
2 1 4 2
2 3
PARTS IDENTIFICATION 11
7 7 8 7 9 10
+ - 24V
RS485
7 6 7 14 7 13 7 23
Figure 2 Configuration of the FC510, FC520 control panel.
0 12 11 24 15 25 26a 26b 26 16 12
SP
- LI
LE
NAC3 12V
+
-
NAC2
+
-
NAC1
+
-
NAC FIRE
+
-
O16
O15
O14
O12O13
O11
O10
O9 OS8
OS7
OS6
OS5
OS4
OS3
OS2
F 10A/25ØV
OS1
+V
B–
L
12 20 22 21 21 20 19 18 17 12
PARTS IDENTIFICATION 13
Description of Parts P. Description
8 Flat cable: for the Display module board con-
This section describes the components of the FC500 nection with User interface board
serie Control panels, and FC500REP Repeater. 9 Jack for the connection between display mo-
dule and User interface board
Unless otherwise stated, the numbers in boldface in this 10 Flat cable: for the User interface board con-
Manual refer to the Tables ands Diagrams in this sec- nection with Main board
tion. 11 Jumper to Default programming (Future use)
(Default //)
The parts identification numbers in the diagrams go cloc- 12 Anchor screw locations
kwise. 13 Signalling LEDs Label
14 Identification Keys Label
P. Description 15 Main Board
1 Surface Cable conduit entry 16 Switching power supply support
2 Door screws 17 Switching power supply screw
3 LED label slots 18 Switching power supply
4 KEYs label slots 19 Anchor for power supply wires
5 Display 20 Batteries (NOT supplied):
6 User interface board FC510, FC520 = 2 da 12 V 17 Ah
7 Nuts to secure the User interface board on the (Accessory item: 2 da 12V 38 Ah -see figure 16-
cover of Control Panel or Repeater 21 Chased cable conduit entry
7a Earth connection (see figure 3) 22 Thermal probe
2 7 7 7 2
a)
+ - 24V
RS485
2 7 7 14 7 6 13 7a 23 2
NAC3 12V
+
-
NAC2
+
-
NAC1
+
-
NAC FIRE
+
-
O16
O15
O14
O13
Figure 4 FC500IP board connection with the motherboard via the flat cable.
P. Description P. Description
23 Jack for the connection between the User interfa- 26a Connection FC500IP with PCLINK cable,see
ce to Repeater (RS485 interface accessory item) note*(2)
24 FC500PS Telecom Module
25 Loudspeaker 26b Power FC500IP,see note*(2)
26 FC500IP board
b)
1
12 12
Washer
Nut M3
Plastic Frame
Repeater PCB
1 1
Support Repeater Cover
Earth connection
12 21 1 12
PARTS IDENTIFICATION 15
26c Connection FC500IP with Flat cable, see + *(2) If you connect the FC500 IP board with the mot-
herboard via flat cable (26c) (Fig. 4) the Digital Com-
note*(2)
municator function will be activated. If the Digital
27 Mains indicator LED (switching power supply)
Communicator function only is requested the
28 Switching-power-supply anchor hole PCLINK cable (26a) and the cables for board power
29 Switching-power-supply output voltage con- are not necessary (26b) (see Figure 4). If both Digital
trol input (connected at factory) Communicator than PC interface functions are re-
30 Fine trimmer for the Switching-power-supply quested the flat cable and the PCLINK cable are ne-
output Voltage cessary, but not the power connection (26b).
! Be
31 Auxiliary power-supply terminals (27.6 V)
sure that the main voltage is the same of the
32 Mains power terminals (110/230V~ 60/50 Hz) input voltage set on the BAQ140T24 power
33 Switching-power-supply screws supplier. Move the switch 35a if the BAQ140T24
34 Switching-power-supply fuse — protects aga- input voltage is different from the main voltage,
inst overload: ONLY when the power supplier is not connec-
BAQ140T24 = F 4A 250V ted to the main power. Please note that the po-
wer supplier will be damaged if it is connected
35 Cable: connects the Switching power supply
to the 230 V main power when it is set for 110 V.
to the Main board (connected at factory)
35a Voltage switch (110V or 230V)
36 Switching-power-supply anchor
37 Switching-power-supply closure rivet
38 Jack for the User interface board
39 Microprocessor
40 RS232 Serial Port
41 Terminal board
42 Terminal board
43 Jack for the thermal probe
44 Jack for the BAQ140T24 Switching power
supply
45 Battery output voltage control panel (connec-
ted at factory)
46 RS485 terminal board
47 Jack for Extinguishment Module (Future use)
48 Jack (Future use)
49 Jack (Future use)
50 Jumper for Earth Fault (Leakage to Earth)
signalling (Default // ) *(1)
110V
Input voltage avoiding damage
Before power on please check
110/220 is selected by switch.
51 Microphone
52 Jack for the connection between User Interfa-
ce board and the Main board
220V
53 Buzzer
54 Control Panel Backplate
55 38Ah Batteries Backplate
56 Connecting Threaded tube
57 Nuts on Control Panel Backplate
58 Nuts on 38Ah Batteries Backplate
F 4A/25ØV
+V
B–
L
* NOTE (1)
Before connecting the Fire control panel to PC for the PC
programming phase, remove the jumper 50 of main bo-
ard.
After the programming phase is finished, replace the
jumper otherwise the Earth fault (Leakage to Earth) will Figure 5 BAQ140T24 Switching-power-supply
not be detected.
+ - 24V
23
RS485
User Interface (see Figure 2, parts 13 and 14) work
through the following steps:
53
1) Remove the screws 2 and open the Control panel or 9
Repeater FC500REP (see Figure 3).
38 49 11 39 50 40 41
NAC3 12V
+
-
NAC2
+
-
NAC1
+
-
NAC FIRE
+
-
O16
O15
O14
O12O13
O11
O10
O9 OS8
OS7
OS6
OS5
48
OS4
OS3
OS2
OS1
42
+ L2 - + L2 - + L1 - + L1 - + - 24V 24A 24R NC NO C NC NO C + - + -
LEFT RIGHT LEFT RIGHT LC RS485 AUX AUX-RES FIRE FAULT BAT2 BAT1 PS1 PS2
47 46 45 44 43 42
Figure 7 Identification of the parts: a) Main board .
PARTS IDENTIFICATION 17
Description of the Control keys
KEY DESCRIPTION
Lamp/Buzz This key can be used to test the buzzer and LEDs . If this key is pressed (when the Control panel is
Test functioning as intended), all the LEDs will glow and the buzzer will emit a continuous beep.
Silence This key can be used to restore the Silenceable outputs to standby status. Silence status will be held
until the Silence key is pressed again in Day Mode, or if the Control panel is operating in Night
Mode, until the Night mode Silence time expires or until a new Alarm/Trouble condition is detec-
ted.
Investigate This key can be used to refresh the “PreAlarm Time”: if this key is pressed during “PreAlarm”, the
remaining PreAlarm time will be increased with the programmed "Recognition delay".
Silence Key to silence the local buzzer of the control panel: the buzzer will be operating every time a new
Buzzer event will be activated
Reset This key can be used to reset the Fire detectors and restore all outputs to standby status (Supervi-
sed/Silenceable outputs, NON-Supervised/Non-Silenceable outputs and Alarm zone outputs)
Evacuate key to activate the evacuation: if this key is pressed for over 2 seconds, the system will generate an
alarm.
F1, F2, F3, F4 Function keys of the Display; their function will be various according to different screen of display
To install the control panel work through the following Installing FC500REP Repeaters
steps:
Ø Choose suitable mounting locations for the Control Repeaters can be wall mounted, or flush mounted to an
panel, detectors, fire warning and fire control devi- ave® BL08 outlet box (or similar).
ces.
Ø Lay the cables between the Control panel and the Work carefully through the following steps.
system peripherals.
Ø If necessary, install any accessory modules. 1. Lay the connection cables (refer to “Connecting
Ø Before mounting the Control panel to the wall, insert Repeaters”).
the LED and Keys Labels (supplied) in the Interface
User (see pag.17). 2. Remove the screws 2 (see Figure 3) and open the
Ø Carry out the necessary connections, leaving the po- Repeater FC500REP.
wer-supply connection until last.
Ø Program the Control panel in accordance with the in- 3. If you are flush mounting the Repeater, go to step
structions in the “PROGRAMMING” section. 5. If you are wall mounting the Repeater, drill the
Ø Test the entire system (Control panel, detectors, fire anchor screw holes 12.
warning and fire control devices).
4. Pull the wires through the wire entry 21, then, using
+ Accessory Modules should be installed before mo-
unting the Control panel to the wall.
the anchor screws, secure the Repeater to the wall.
1. Remove the screws (2) and open the Control panel. Installing the FC500 Slave control panel
2. Drill the anchor screw holes. See "Installing the Control panel paragraph".
INSTALLATION 19
Description of the Terminals [NC][NO][C] FIRE Non-supervised fire output. Dry
contact relay for non-supervised devices:
This section describes the Control panel terminals.
Ø During standby status —— terminal [C] closes to ter-
n Main Board terminals minal [NC];
Ø In the event of fire —— terminal [C] closes to terminal
+L1-/LEFT (+)Loop 1-Positive signal, left side. [NO].
(-)Loop 1-Negative signal (return), left side.
[NC][NO][C] FAULT Non-supervised fault output. Dry
+L1-/RIGHT (+)Loop 1-Positive signal, right side. contact relay for non-supervised devices:
(-)Loop 1-Negative signal (return), right side.
Ø During standby status —— terminal [C] closes to ter-
+L2-/LEFT (+)Loop 2-Positive signal, left side. minal [NC];
(-)Loop 2-Negative signal (return), left side. Ø In the event of fault —— terminal [C] closes to termi-
nal [NO].
+L2-/RIGHT (+)Loop 2-Positive signal, right side.
(-)Loop 2-Negative signal (return), right side.
+ EN54-2 cerification applies ONLY when, FAULT
output is not J (EN 54-1) type, therefore this output
+ Each Loop supports 250 (Analogue detectors, Input
modules, Conventional Zone modules, Manual callpo-
MUST NOT UTILIZED to manage Fault transmis-
sion devices.
ints, Output modules and Sounders). In all the control
panel supports up to 500 devices with 2 Loop. +BAT2- Terminals to connect the batteries inside the
FC500 control panel (see Figure2).
LC Conventional Input Line - Supervised and
Bypassable (Disabled) — This line supports 30 con- +BAT1- Terminal to connect remote batteries or Po-
ventional fire devices (Optic Smoke detectors, Heat de- wer supply.
tectors, Manual callpoints).
PS1 BAQ140T24 power supply first connector.
Connect terminal [LC] to ground terminal [ M]) using a
PS2 BAQ140T24 power supply second connector.
3900 ohm resistor (orange-white-red). A 680 ohm resi-
stance (normal value for Fire detectors) parallel to the
OS1...OS8 Programmable, Silenceable, Bypassa-
3,900 ohm resistor will activate the programmed actions
and preset times of the Conventional Line outputs and the ble (Disabled), Supervised Outputs.
Non-supervised output (terminals NC, NO and C). These are normally-open terminals (open-collector)
which will close to ground, when the connected event
+ NOTE:
voltage terminals [M] and [24V].
The EOL resistor must be connected to
AUX Auxiliary power 24 V (0.5A max) Power supply to the last device on the Supervised output. Connect
devices that operate at 24 V (powered by the standby a diode (1N4002 or 1N4007) in series to the devi-
batteries): ces connected to these outputs.
27,6V
FireClass
LOAD
Osx
1N4007
27K
SUPERVISED
INSTALLATION 21
LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT
+ L2 - + L2 - + L1 - + L1 - FireClass + L2 -+ L2 - + L1 - + L1 - FireClass
L- L- L- L-
L+ L+ L+ L+
A A A A
L- L- L- L-
L+ L+ L+ L+
L- L-
B B
L+ L+
1) 2)
L- L-
B B
L+ L+
L- L-
B B
L+ L+
L- L-
B B
L+ L+
L+ L- L+ L-
B B
Figure 9 1) Wiring diagram of a 2-wire connection - 2) Wiring diagram of a 4-wire connection: a) Insulators; b) Com-
patible analogue devices (Fire detector, Input modules, Output modules, Conventional Zone modules, Manual callpo-
ints); c) T connection.
+ Ifonthetheconnection
left
is 2-wire connection type, connect Connect the Conventional Fire detectors in parallel to
terminals [LC] and [M].
The resistor (3,900 ohm) connected to these terminals
n Connecting Conventional Devices must be moved to the terminals indicated in the instruc-
Connect Conventional devices to terminals [M] and tions of the last device on the Conventional Line (see
[LC]. Fire detectors and Manual call point. figure 9a).
A)
FireClass
LC
A+ B+ NA A+ B+
680 W
EOL End of
line resistor
(3K9 1/4 W)
B)
FireClass
LC
A+ B+ A+ B+ NA
680 W
EOL End of
line resistor
(3K9 1/4 W)
C
RS485
Figure 11 Wiring diagram of two FC500REP Repeaters and two FC500 Slave Control panels connected to the RS485
n Connecting Repeater and Slave Control panel When several Control panels are in the system, the Re-
An example of how to connect two FC500REP repea- peaters supply Load can be shared between these
ters and two FC500 SLAVEs is shown in Figure 10. Control panels (see Figure 11).
24V
24V
24V
Figure 12 Network connection example: the Repeaters supply load is shared on several Control panel. In this case
the“Repeater 1” is supplied by "Master" panel while the “Repeater 2” is supplied by ”SLAVE” control panel.
INSTALLATION 23
+
+
1N4002 1N4002 1N4002
NAC FIRE
NAC FIRE
A+ A+ A+
3k9 3k9 3k9 3k9
-
-
(a) (b)
Figure 13 Wiring diagram of the connection of a single device (a) and several devices (b) to Bell outputs (device acti-
vated by positive (27.6 V) on terminal [A+]).
FireClass
NAC FIRE
–
+
AUX C NC NO
+N –L –A + – + –
Line
230 V Neutral
50 Hz
Earth
BLACK wire
RED wire Jumper
Automatic
+ – + – isolating
switch
12 V Battery 12 V Battery
INSTALLATION 25
NAC3 12V
+
-
NAC2
+
-
NAC1
+
-
NAC FIRE
+
-
O16
O15
O14
O12O13
O11
O10
O9 OS8
OS7
+ - 24V
OS6
RS485
OS5
OS4
OS3
OS2
F 10A/25ØV
OS1
AC/L AC/N FG GND +V
GND
B+
+V
B–
L
+ L2 - + L2 - + L1 - + L1 - + - 24V 24A 24R NC NO C NC NO C + - + -
LEFT RIGHT LEFT RIGHT LC RS485 AUX AUX-RES FIRE FAULT BAT2 BAT1 PS1 PS2
12 1 1
12
12
54 57 56
12 59 59
55 58
Figure 16 Control Panel and 38Ah Batteries metal Box connection (accessory item).
Work carefully through the following steps (see Figure The following operations must be carried out regularly.
16).
A Using a damp cloth (DO NOT USE SOLVENTS OF
1. Remove the screws (2) and open the metal box. ANY KIND), remove dust from the Control panel case.
2. Drill the anchor screw holes. B Using the Lamp/Buzz/Test key, check that the
LEDs and buzzer are functioning properly.
! Check for water pipes and electrical wiring be-
fore drilling. C Ensure that the batteries are sufficiently charged and
functioning properly. If not, replace them immediately.
3. If necessary, using a hammer or similar tool, remo-
ve the surface conduit wire knockouts 1. D Ensure that all cables and connections are intact.
4. Secure the metal backplate to the wall E Ensure that there are no unrelated objects inside the
Control panel case.
+ The cable conduit union with the case must be se-
cured by HB Flame Class (or higher) lock nuts. + Points A and B may be carried out by users.
Points C, D and E must be carried out by qualified
Pull the wires through the chased wire entry 1 and con- persons only.
nect them. See paragraph: Connecting a power supply.
a)
29,0
VOLTAGE (V)
28,0
27,4
27,0
26,0
-10 -5 0 5 10 15 20 22 25 30 35 40 45 50
TEMPERATURE (°C)
Figure 17 Switching Power Supply Output Voltage graph. To find the Output Voltage using the graph: — indicate the
Probe temperature on the TEMPERATURE (°C) axis; draw a line from the temperature value point up to the curve a);
draw a line from the intersection point across to the VOLTAGE (V) axis; adjust the Output Voltage of the Switching Po-
wer Supply to the resultant value. For example, if the Probe temperature is 22 °C, the Output Voltage of the Switching
Power Supply must be set at 27.4 V.
VOLTAGE (V) 29,0 28,8 28,6 28,2 28,0 27,8 27,4 27,2 27,0 26,8 26,6 26,4 26,2
Table 5 Switching Power Supply Output Voltage chart. To find the Output Voltage using the chart: — select the nea-
rest value to the Probe temperature on the TEMPERATURE (°C) row; read the respective value on the VOLTAGE (V)
row; adjust the Output Voltage of the Switching Power Supply to the indicated value. For example, if the Probe tempe-
rature is 22 °C, the Output Voltage of the Switching Power Supply must be set at 27.4 V.
INSTALLATION 27
a) b) c)
F 3.15A/25ØV
F 3.15A/25ØV
AC/L
AC/L
AC/N
AC/N
FG
FG
F 6.3A/25ØV
F 6.3A/25ØV
B+ B+
L L
B– B–
GND GND
+V +V
GND +V
GND +V
NO YES
Figure 19
1 1 13
6 6 25
2 2 12
7 7 24
3 3 11
8 8 23
4 4 10
9 9 22
5 5 9
21
a) DB9 Female 7- wire cable DB9 Female 8
20
Connector shield Connector 7
19
6
18
5 5
9 17
4 4
8 16
3 3
7 15
2 2
6 14
1 1
b) DB9 Female 7- wire cable DB25 Female
Connector shield Connector
Figure 18 Wiring diagram for the serial link between the Control panel and PC
You can program this system from the Control panel or Control panel connections
from a computer, using the FireClass 500 Console ap-
plication, inside the FireClass Suite. If you are using the Supervisory, Management, Downlo-
This section describes how to program the system from ading and Log Management functions, the control panel
a computer. If you intend programming the system from must be connected to your PC in local communication
the Control panel refer to the “PROGRAMMING FROM or remote by PSTN line, GPRS or LAN.
THE PANEL” section.
To connect the control panel in local:
(see note page n. 16)
Introduction
Using a CVSER/9F9F cable (accessory item) or similar
The FC500 software console contains: cable (see figure 18), connect the control panel serial
Ø FC500 console : the application to manage and pro- port (refer to “PARTS IDENTIFICATION”) to a serial
gram the FC500 series control panels. port on your PC.
Ø Select the PC serial port from the Option menu
(Choose serial port ) and then Click-on 3 OK,.
Installation For 25 pin serial ports, use an ADSER/9M25F adapter
(accessory item) or make a cable as per figure 18b.
Work carefully through the following steps to install the
FC500 software applications. If the control panel is not connected to your PC when
Ø Run the Setup.exe application contained in the you start the communication, the following warning will
CdRom "Fire Suite". be shown: "Communication error! Check serial link"
Ø Select a folder for the FC500 software applications. If the serial port for the local communication is invalid,
Ø Run as Administrator. the following warning will be shown: "Cannot open se-
rial port".
Select language
Main window
You can select the language of the FC500 Software,
from the Languages provided. The FC500 Software opens on the Main window (see
fig. 20). The following section describes the File,Com-
To Select the application language:
Ø Run the FC500 Software application;
Ø Select Options from the Main window;
Ø Select Language from the drop-down menu to open
a window with the language list;
Ø Select a language from the Language list;
Ø Click-on 3 OK,
The selected language will be immediately initialised.
PC PROGRAMMING 29
Figure 21 New panel window(Type of control panel)
n Icons description
Ø Click-on this icon to upload all the programming Ø Click-on this icon to remove the selected Slave
(via serial link) of the connected control panel. control panel, after a request of confirmation.
pansion board.
pansion board.
mer window.
Installer Password.
Exit Click-on "Exit", the FC500 software will be closed. Devices programming
Export configuration file: Click-on this option, all the Click-on Control panel name, and than on Loop1 or Lo-
data customer will be exported in a single file. op2, the devices programming window will shown (Fi-
gura 26).
Import configuration file: Click-on this option, all the
data customer will be imported from a single file.
+ Close Loop1 or Loop 2 name, in the round brackets
( ) there is the Loop devices number.
n Communication
In this menu: the option Firmware Upgrade only. n Description of the icons in the tool bar.
Firmware upgrade Click-on "Firmware Upgrade": the Ø New Device: select new devices;
window (see figure 23) will be shown.
From a source file, this option allow you to do the Fir- Ø Remove device: remove the installed devices;
mware Upgrade of all system interface: Mainboard, Ø Copy device on clipboard: allow you to copy the
User interface, Loop controller. devices data and after paste them in another customer.
n Options
In this menu you find the options: serial Port,
Language and Realtime options . See the pre-
vious paragraph: "Select language", "Control pa-
n Database
The Database menu provides the following op-
tions: Maintenance and database Options .
PC PROGRAMMING 31
Min.Static Max.Static
Typical application Max. Application
Detector Response Response
Temperature Temperature
Class Temperature Temperature
°C °C
°C °C
A1 25 50 54 65
A2 25 50 54 70
B 40 65 69 85
C 55 80 84 100
D 70 95 99 115
E 85 110 114 130
F 100 125 129 145
G 115 140 144 160
Table 6 Detector classification Temperature - Detector shall conform to one or more of the following classes: A1,
A2, B, C, D, E, F o G . Manufacturers may optionally give additional information concerning the type of response exhi-
bited by the detector, by adding the suffix S or R to the above classes.
Detectors, with a suffix S to their class, do not respond below the minimun static response temperature, even at high
rates of rise of air temperature.
Detectors, with a suffix R to their class, incorporate a rate of rise characteristic, which meets the response time requi-
rements for high rates of rise of air temperature even when starting at air temperature substantially below the typical
application temperature (EN54-5:2000).
+ As
for the detector (click on available bases).
Ø Processing section: different styles are selected, the electrical ope-
Processing: this determines the actions the control rating diagram changes
panel will perform when the device threshold is exce-
eded. n Output modules programming
Click-on an entered Output Modules, the relative pro-
Drift Compensation: Drift compensation effects analo-
gramming window will shown as per the following de-
gue smoke sensors only. It will supply a precise anal-
scription.
ysis about dust accumulation, and therefore, the alarm
threshold will be modified accordingly.
Output module section: as per the same Detectors sec-
tion;
Use zone setting: the detector uses the parameters
Assigned zones: each Output module can be associa-
of the assigned zone; if this options is disabled, the pro-
ted with up to 4 of the 64 avalaible software zones for
cessing type will be selected.
FC510 control panel, (128 for FC520). An Output mo-
dule will activated when the zones where is enabled will
Prealarm - the control panel will activate the ALARM
go into ALARM status.
delay;
Base In this section it is possible to select the base for
Warning - the control panel will activate a WARNING
the Output module, click on available bases (for
signal.
FC430SAM and FC430SAB only).
Beacon It is possible activate the blinking or glowing (ON)
Operating mode Heat detector:
Assigned points: each Output module can be associa-
Day mode-Night mode for Temperature detector (see
ted with 3 Input Points. If any one of its Input Points
table 6).
goes into ALARM status, the Output module will activa-
Operating mode Smoke detector: Day mode-Night
te. For each Point it is necessary to indicate:
mode for Smoke and Heath detectors:
Ø the loop the device is connected to (1 or 2);
Ø Default: for smoke detectors only (813P) and for
Ø the device address.
Smoke and Heath detectors only (801PH)
Options section: this option will allow you to select the
Ø Enhanched: (for Smoke and Heath detectors only)
conditions that will activate the output module:
Ø Sensitivity: Sensitivit can set:
Ø Zone warning, Zone fault, Zone Prealarm, Zone Alarm,
Low, Medium and High.
Zone Double Knock;
Ø Point warning, Point fault, Point Prealarm, Point
+ Click-on yellow bar to open or close the relative
section of parameters programming
Alarm,
Ø Panel warning, Panel fault, Panel prealarm, Panel
+ Ifdule,
alarm,
a detector linked to an Output or Input-Output Mo-
Ø Network warning, Network fault, Network prealarm,
will be disabled (remove a tick [3] in the proper
Network alarm,
section), a window will shown to ask confirmation.
moreover it is possible to program the Output Module
Click on Detail to see further data (Figure 27).
as: Silenceable, Pass trough and Walk test.
PC PROGRAMMING 33
see the customized Manaul), the relative programming The procedure can be triggered via software or panel
window will shown. (see page 47)
The Zone option from the pull-down menu will allow you to
+ If the procedure to "restore the factory defaults" of
control panel will be executed (see Icon descrip-
access the software-zone parameters (see Figure 28). tion), even the FC500PSTN Interface is restored to
The software zones parameters will be applied automati- the factory defaults, while the programming data of
cally to all the devices associated with the zone concerned. FC500IP are not affected.
First section (see Figure 28) on the right;
Ø Enable: a tick [3] indicates if the zone is enable. Outputs Programming
Ø Label: this is for the editable device-label (up to 20
characters). The system will use the label as the The Outputs option from the pull-down menu will allow
zone identifier. you to access the outputs parameters. The relative pro-
Ø Preallarm Duration: an input device programmed with gramming will shown as per the following description
Prealarm time will generate ALARM status when the (see Figure 29).
prealarm time elapses. (see parameters programming
detector). n NAC1, NAC2 and NAC3 Outputs
Select the Prealarm time; Supervised/Silenceable/Bypassable (Disabled) Alarm
the default prealarm time is 1 minute. Outputs.
Enter values of 0.00 through 10.00 minutes with Output ACTIVE: positive pull-up to 27.6 V on the [+] ter-
steps of 5 seconds. minal; negative pull-down to 0 V on the [–] terminal.
Options section: many parameters can be program- Click-on a Output, the relative programming window will
med in this section. shown:
Ø Walk test: if this option is enabled, the zones in In the first sezione:
alarm status will activate the programmed
Outputs with Walk test, while the control panel
will not generate an alarm.
Ø Detector Warning: if this option is enabled the
control panel will activate a WARNING signal.
N.B. To activate the Warning option for a Mo-
dule, tick the corresponding box on the Module
programming screen.
Ø Prealarm: if this option is enabled, the control
panel will activate the ALARM delay.
Ø Drift Compensation: see the same option in
"Parameters detectors Programming";
Ø Double Knock: if this option is enabled and
the zone is in Prealarm status, when an other
devices (other address) associated to this
zone will be activated, the zone will immedia-
tely generate an Alarm status.
Ø Smoke delay: for each zone, you can program
the delayed activation of the smoke detectors. Figure 28 Zones Programming window.
+ the
When Program as NACFIRE has been ticked,
NACFIRE output indicator light blinks if the
NACFIRE output and/or NAC1 output breaks
down; it remains Glowing if the NACFIRE out-
put and/or NAC1 output is disabled.
Figure 30 General Options programming window.
Assigned zones: : each Output can be associated
with up to 4 of the avalaible software zones (64 for FC510 Linked Delay One of the 5 available timers (set using
128 for FC520 control panel). the General Options screen) may be associated with an
Assigned points: each Output can be associated with 3 output activated by a zone, point or control unit alarm. The
Input Points. If any one of its Input Points goes into output will be activated to coincide with the programmed
ALARM status, the Output will activate. For each Point it event, after the delay indicated by the Timer.
is necessary to indicate:
Ø the loop the output is connected to (1 or 2); General Options programming
Ø the address.
The Panel parameters can be programmed through the Ge-
Options Section: this options will allow you to select neral Options from the pull-down menu (see Figure 30).
the conditions that will activate the outputs; exaple: if
"Zone warning" option is enabled, the control panel will Delays section In this section it is possible to program:
activate the output when one of its associated points Ø Recognition delay: a Delay will be added automati-
goes into Warning status. cally to the Prealarm remaining delay, when the Inve-
Ø Zone Warning, Fault Zone, Prealarm Zone, Alarm stigate Key will be pressed.
Zone, Double knock (see Zones programming),
Pass trought, zone Walk Test ;
Ø Point Warning, Point Fault, Point Prealarm, Point
+ The sum of Recognition delay and Prealarm
Time must not exceded 10 minutes
Alarm, Network warning, Network fault;
Ø Panel Warning, Network Warning, Panel Fault, Main Fault delay: in this field it is possible to program
Network fault, Panel Prealarm, Network prealarm, the delay of signalling of Mains failure.
Panel Alarm, Network alarm, Backup PSTN line (see The green signalling LED (Main OK) will be OFF, the
FC500PS manual). Amber signalling LED (Main Fault) will be ON, the rela-
tiv event will be shown on the diplay.
n OS1....OS8 Outputs
Positive outputs - Programmable - SUPERVISED
—— Terminals for supervised devices activated
by positive (24 V):
Output active — positive (27.6 V) on terminal
[OS]; ground on terminal [M].
See the parameters descriptions as per Uscite
NAC1, NAC2, NAC3 Outputs.
n O9....O16 Outputs
These are programmed, NON-SUPERVISED,
non-silenceable, bypassable (Disabled) outputs.
These are normally-open terminals (open-collec-
tor) which close to ground when the correspon-
ding zones go into alarm status. These terminals
will remain closed to ground even after the gene-
rating event has ended.
See the parameters descriptions as per NAC1,
NAC2, NAC3 Outputs.
Figure 29 Outputs programming window.
PC PROGRAMMING 35
Prealarm duration: an input device programmed with
Prealarm time will generate ALARM status when the
+ The Slave control panel address can be inserted
from the User interface of the same control panel;
prealarm time elapses. the Repeater address can be inserted from the pa-
Prealarm status is signalled by: an audible signal emit- nel of the same Repeater (see Programming from
ted by the control panel; the panel).
Ø blinking on the PREALARM LED;
Ø the message on the display; The FC500PSTN interface and the FC500IP module
Ø activation of outputs with programmed Prealarms. are enabled in the Communicators section. A single
Silence duration: when the control panel is in Night click means the interface will be present but not active,
Mode the Silence delay is the maximum silence time of while a double-click enables the FC500PSTN or
the Outputs. FC500IP module. You may also choose whether to
Reset: program the Reset time ( min Time: 2 sec; max enable both alarm and breakdown events or just one of
Time: reset AUX-RES Output, see AUX-RES terminal). the two. The delay times corresponding to the zone, po-
Password section: the Password section will allow int and control panel alarms are set in the Alarm Ti-
you to change the Installer and User codes. Codes mers section.
with 1 to 5 digits (0 through 9).
Installer code allows to manage the 3 access Levels of Languages:in the Languages section, you have the
control panel: L1(View), L2 (User), L3 (Installer). option to change the system language from those avai-
The default installer code is 00000: every digit will be lable. Once in the Available Languages have loaded
hidden by *(star) symbol. the two languages among those available, press the
User code allows to manage 2 access Levels of con-
trol panel: L1(View) and L2 (User). button to overwrite one of the two languages in the
The default User code is 11111: every digit will be hid- panel memory. As soon as the download of the new lan-
den by *(star) symbol. guage will be completed, the plant will start to use it, and
update their device, if necessary. To change the lan-
Loop section: in this section select the required Loop guage currently active on the system, use the button
configuration: a 2 wire connection or a 4 wire connection. in the section Change system Language.
Language section: select the avalaible language the
display of Control panel and Repeater will use. It is pos- Advanced In the Advanced section you have the
sible to upload others languages from the software. possibility to set the thresholds for gas detection device
Day-Night mode section: select the DAY or NIGHT
mode, or a tick [3] on Automatic enter the time (hour FC410DDM, press the icon .
and minutes) when the day-night mode changes.
PSTN interface
+ When you set the time to transition from DAY to
NIGHT mode make sure that the time is less than
For an explanation of the various commands and pro-
the hour to be set for switching between Day and
gramming procedures, please refer to the dedicated
Night mode.
FC500PSTN manual.
FC500REP: a tick [3] enables the Repeater faults si-
gnalling.
Network: a tick [3] on Enable Network enables the
Slave control panel on the Network, and a a tick [3] on
Network Commands enables the Control pa-
nels that have the same tick [3] to do the com-
mands (Reset, Silence, Investigate) programmed
in other Network control panels.
Allow silence buzzer: If this option is enabled it is
possible to silence a device that is activated by
every part of the network.
For an explanation of the various commands and pro- The Battery calculation window allows you to see (Figu-
gramming procedures, please refer to the dedicated re 31):
FC500IP interface manual. Ø the FireClass500 Loads
Ø the Loop1,Loop 2 devices loads
CLOCK in the condition of Normal Load and Alarm Loads
(percentage of devices in alarm status), when the Ma-
The Date/Time option from the CLOCK menu is for the ins faults.
control panel clock settings. Below this window, in the option "Others Load", if nee-
Enter the required Time and Date. ded, the Loads on Auxliary terminals will be inserted.
In case schedule the automatic application of summer Automatically the Total Load and the Battery needed
time if required. will be shown.
PC PROGRAMMING 37
PR
200 200
INSER
WRONG
PASSWORD
INSTALLER Lev. 3
PASSWORD
310
1 2 3 4 5 6 7 8 9 0
AUTO DEVICE SW ZONE OUPUT NET TELECOM OPTION SYSTEM DEFAULT L3 PWD
Lev. 1 330
1 2 3 4 5 6
430 430
431
CHOOSE
LOOP
432
CHOOSE
DEVICE
Figure 32 Diagram of all possible operations from the panel, L1, L2 and L3 Levels
F1 F2 F3 F1 F2 F3
ROGRAM ANALYZE VIEW LOG F4 DIASABLE VIEW LIST MODIFY
200 200
WRONG INSERT USER
200 200
PASSWORD PASSWORD Lev. 2 WRONG INSERT USER
PASSWORD PASSWORD Lev. 2
323 320
SELECT WHAT TO BE DISABLED/ENABLED SELECT WHAT MODIFY
1 2 3 4 5 6 7 1 2 3 4
LIST DEVICE SW ZONE OUTPUT NET TELECOM CONV. ZONE CHANGE
DATE & TIME
PANEL NAME USER PWD
CLEAR LOG
INSERT INSERT
430 430 430 430 430 INSER PANEL NEW USER
CHOOSE CHOOSE CHOOSE CHOOSE CHOOSE NAME PASSWORD DATA & TIME
PANEL PANEL PANEL PANEL PANEL 800 200 800
431
CHOOSE LOG CLEARING
LOOP
432 440 440 440 440
CHOOSE CHOOSE CHOOSE CHOOSE NET CHOOSE
DEVICE SW ZONE OUTPUT EQUIPMENT INTERFACE
Lev. 1 340
VIEW LISTs
7 8 9 1 2 3 4 5 6 7
FW VERSION DISABLED DISABLED DISABLED SW ZONE IN WARNINGS ACTIVE
OM OPTION LOG FAULTS LIST
ZONE DEVICES PARTS WALK TEST LISTS WALK TEST
SCAN & SHOW SCAN & SHOW SCAN & SHOW SCAN & SHOW
SCAN & SHOW SCAN & SHOW SCAN & SHOW
SW ZONES ACTIVE DEVICES IN
DISABLED SW ZONES DISABLED DEVICES DISABLED PARTS IN WALK TEST ACTIVE FAULTS WARNINGS WALK TEST
A70* A70* A70* A70* F00 F00 F00
F00
F1
ALARM
F2 F3 F4
F00
PRE ALARM
F2 F3 F4
F00
FAULT
F2 F3 F4
F00
WARNING
F2 F3 F4
F00
WALK TEST
F2 F3 F4
PC PROGRAMMING 39
+ The wire database data is stored in the file "Wire-
sList.fcw" inside the FireClass 500 Console Lan-
guage folder. The database can be moved from
one system to another. The Console searchs for
the wire database while starting, so, if the user can-
not access a moved database, simply close the
software, and start it again.
User mode
Read through the following section carefully, in order to n L3= Third Level or INSTALLER Level: access to
get an overall view of how to use the User interface Pro- this level requires entry of the INSTALLER PIN
gramming (Main panel) of control panel. (Access Level 3).
This level allows all the operations of the First and Se-
For details regarding the parameters of each phase, re- cond Level, moreover allows to program the security
fer to the respective paragraph in the system; the Programming phase allows the installer to
“PROGRAMMING FROM A PC” chapter. program the control panel and peripheral devices (de-
tectors, modules, repeater and slave panels), in details:
AUTO, DEVICES, SW ZONES, OUTPUTS,
Using the system NETWORK, TRANSM., OPTIONS, SYSTEM,
DEFAULT and PWD L3
The FC500 system can be managed from the User in-
terface (main panel) and/or through the FireClass500 n Operating the system
Console application (the computer must be connected To manage the system from the User interface (Main
locally via RS232 serial port). The User interface (main panel) is used the Alphanumeric keypad, the Cursor
panel) allows access to different Level authorized. keys, the ESC Key ESC
, the ENTER key and the
F1 F2 F3 F4
There are three different access levels, as follows. Functions Keys F1 ,F2 , F3 and F4 .
n L1= First Level: this level allows the Reading + Insordetail the use of Alphanumeric keypad, the Cur-
keys, the ESC Key , the ENTER key and the
Parameters ONLY:
- F2-ANALYZE button (see Figure 36) views the status Functions Keys F1, F2, F3 and F4 is shown in
of the: LOOP, DEVICE, SW ZONES, OUTPUT, every page of
NETWORK, TELECOM, OPTIONS, LOG and the FW PROGRAMMING/DISABLE/MODIFY/READING
Vers.; PARAMETERS.
In this phase:
Current phase
Figure 33 The Main Page of Display
the default installer code is 00000: every digit will be Master Panel lev.3 : PROGRAM
INSTALLER
hidden by *(star) symbol.
Wrong Password
From Main page, use the F1 Key to select the Program- The Auto option from the PROGRAMMING menu will
ming phase. Insert the password (installer code) and allow you to enrol the loop devices and the RS485 net-
then the page is shown in Figure 36: work devices automatically.
ENROLLING IN PROGRESS
PLEASE WAIT
b)
Differences found!
1:New configuration
2:Add new devices
3:Discard changes
Figure 37 Auto (Enrolling) results pages Figure 38 Insert-Modify password (Installer code).
The Restore Default option from the PROGRAMMING The Device command in the PROGRAMMING menu
menu will allow you to restore default setting. activates the screen used to select and program the de-
vices on the loops;
Use the 9 Key to select Restore Default, the display
will show the Figure 39: The Alphanumeric keypad The Alphanumeric key-
pad is used to digit the address of the device.
in this phase:
Cursor Keys No function is related to UP Key;
Alphanumeric keypad No function is related to No function is related to Down Key;
Alphanumeric keypad. The Right key selects the next available device;
The Left key selects the previous available device
Cursor Keys No function is related to UP Key;
No function is related to Down Key; ESC key : ESC key deletes the procedure and returns
No function is related to Right Key; to the previous page;
No function is related to Left Key .
ENTER The ENTER key accepts the selection and acti-
ESC Key The ESC Key deletes the procedure and re- vates the corresponding programming page.
turns to the previous page;
Function Keys No function is related to F1 key;
ENTER key The ENTER Key starts the default settings No function is related to F2 key;
restore procedure. The F3 key resets the address value entered using the
numeric keypad;
Function Keys No function is related to F1 key; No function is related to F4 Key.
No function is related to F2 key;
No function is related to F3 key;
No function is related to F4 Key.
Control panel
Access Level Status
Programmed
address
Detector
to program
Figure 39 Restore default page Figure 40 Pages of Selecting and programming Devi-
ces on Loop
The SW zone command in the PROGRAMMING menu For each zone, you can program the delayed activation
activates the screen used to select and program the of smoke detectors, according to the following schedule:
Software zone on the loops; when the smoke level exceeds the threshold of alarm,
the panel does not signal anything at first;
The Alphanumeric keypad The Alphanumeric key- - after 60 seconds if the smoke level is still above the
pad is used to select the number of the zones. threshold, the system goes into alarm condition, other-
wise there are no signals;
Cursor Keys No function is related to UP Key; - within 30 minutes, a new level exceeded the threshold
No function is related to Down Key; of alarm or activation of another sensor in the same
No function is related to Right key; zone causes the alarm of control panel.
No function is related to Left key.
To program the delay on the activation of smoke detec-
ESC key The ESC key deletes the procedure and re- tors, from Programming menu: SW Zone (KEY 3).
turns to the previous page; - After selecting the SW Zone, on the following display
about the zone to test, select OFF and press Enter.
ENTER The ENTER key accepts the selection and acti- - on the following display about the new option "Detec-
vates the corresponding programming page. tor alarm verification", select ON (to enable) and press
Enter.
Function Keys No function is related to F1 key; In this phase:
No function is related to F2 key;
The F3 key resets the value entered using the numeric Cursor Keys No function is related to Up key;
keypad; No function is related to Down key;
No function is related to F4 Key. Use the Righ key to select: On-OFF;
Use the Left key to select: On-OFF.
After selecting the SW Zone, you will be able to enable
or disable the option Zone in TEST (ON) or not (OFF); in ESC key Use ESC key to delete the operation and to
this phase: step back to previous page.
Cursor Key No function is related to UP Key; ENTER key Use the ENTER to accept the selection
No function is related to Down Key; and activate the programming page.
Right key: selects ON -OFF;
Left key: selects ON-OFF.
c)
b)
SW Zone lev 3: PROGRAM
SW Zone lev 3: PROGRAM DELAY.SMOKE Master Panel
ZONE IN WALK TEST Master Panel Name of
selected On OFF
On OFF Control Panel ^
Figure 41 Pages of Selecting and programming of Figure 42 Page of programming option delay Detec-
SW zones tor alarm verification
The Outputs command in the PROGRAMMING menu The programming NAC Outputs can be activated on di-
activates the output programming screen. If KEY 4 is sablements of any part of the system.
used to select Output programming, you will be asked
to select the output you wish to program; this will be fol- From PROGRAMMING Menu select Output (KEY 4)
lowed by the programming procedure for that output. and than work through the following steps:
n Choose Output -insert the number of NAC you want to program the op-
In this phase: tion "NAC active on disablements";
-in the following diplay insert the name of Output and
Alphanumeric keypad The Alphanumeric keypad is than press ENTER;
used to select the number of the Output. -in the following diplay, press ON to enable the new op-
tion and than press ENTER.
Cursor Keys The UP Key: shows the next/previous
output category (NAC-OC-OS); In this phase:
The Down Key shows the previous output category;
No function is related to Right key. Cursor Keys No function is related to Up key;
No function is related to Left key. No function is related to Down key;
Use the Righ key to select: On-OFF;
ESC Key Use ESC key to delete the operation and to Use the Left key to select: On-OFF.
step back to previous page.
ESC key Use ESC key to delete the operation and to
ENTER Key Use the ENTER to accept the selection step back to previous page.
and activate the view of the next page.
ENTER key Use the ENTER to accept the selection
Function Keys No function is related to F1 key; and activate the programming page.
No function is related to F2 key;
Use the F3 key to reset the value entered using the al-
phanumeric keypad (if incorrect). Navigate using the
+ Ifsilenceable.
a NAC has this option programmed, it shall be not
Outputs type
Master Panel lev 3: PROGRAM
NAC Output: 001 Control panel
Output
Access Level Status
Up or Down to select the type Number
Enter the NAC Output number
NAC Output 001 lev.3 :PROGRAM
Outputs type
OUTPUT NAME
Output Control panel
Number Access Level Status [ ]
At default, every FC500 Control panel is a Master Con- To program the module FC500MFI, do the following
trol Panel disabled in the Network. from Programming menu (Network), press 5 key.
+ Ifverify,
a control panel is already configured as "Master",
via PC, if it is enabled in the Network.
In the programming page "Network" press the ENTER
key to confirm the type of panel (FC500MFI),
If a control panel is already configured as "Slave",
in the new installation, insert the Slave address Select and enable one or more FC500MFI modules
from the user interface of the Contro panel itself. (max 4);
In the Network ONLY one Master control panel select a module by the arrow ï or ð (the symbol ^ un-
must be present. der the name show the selected module),
enable a module by the arrow ñ or disable it by the ar-
When all the Control panels and the Repeaters are con- row ò:
nected in the Network, the system can be supplied. the module name, if enabled, will appear in uppercase
Now it is necessary to configure the Network, so work (see figure n.46).
through the following steps: Press the Enter key to confirm.
1- use the 5 Key to select Network, from Programming
page (Figure 45) in the User interface of the control pa-
nel to be configured;
+ For an explanation of the features and program-
ming (addresses), see the dedicated manual of the
2- the Display of Figure 45 will be shown; FC500MFI module.
3- use the cursor keys to select the type of control panel
assigned as "Slave" (address); in this phase:
4- use the Enter key to confirm.
Alphanumeric keypad No function is related to the
+ Every "Slave" control panel inserted in the Network
must have a different address.
Alphanumeric keypad.
No function
Function Keys
is related to F1 key;
No function is related to F2 key;
No function is related to F3 key;
No function is related to F4 Key.
Figure 45 Page to program the address of Slave con- Figure 46 Display to enable the FC500-FMI module
trol panel.
The Telecom option in the PROGRAMMING menu ac- The term OPTIONs in the PROGRAMMING menu acti-
tivates the transmission device programming page. If vates the DAY-NIGHT-AUT mode programming page.
Key 6 is used to select Telecom device programming, If Key 7 is used to select Functioning mode, Figure 48
you will be taken to the Voice message recording/repla- will show:
ying page, Figure 47:
in this phase: + For an explanation of Day mode and Night mode
operation, please refer to page 6. If you select Auto-
Alphanumeric keypad The Alphanumeric keypad is matic, switching between one mode and the other
used to select the number of the Voice message. will take place automatically.
ESC Key Use ESC key to cancel the operation and to Cursor Keys No function is related to UP Key;
step back to previous page. No function is related to Down Key;
Use the Righ key to select the next operating mode.
ENTER Key No function is related to ENTER Key. Use the Left key to select the previous voice message.
Function Keys No function is related to F1 key; ESC Key Use ESC key to cancel the operation and to
Use the F2 key to start the record of voice message; step back to previous page.
Use the F3 key to start the play of voice message;
Use the F4 Key to stop the record or the play of the voi- ENTER Key ENTER Key accepts the selection.
ce message.
Function Keys No function is related to F1 key;
+ The transmitter (Telecom module) can record 32
voice messages up to 8 seconds long – See chap-
No function is related to F2 key;
No function is related to F3 key;
ter “Appendix: FC500PSTN” No function is related to F4 key.
Mode type
Alphanumeric keypad No function is related to the ESC Key Use ESC key to cancel the operation and to
Alphanumeric keypad. step back to previous page.
Cursor Keys No function is related to UP Key; Tasto ENTER Use the ENTER Key to confirm the ad-
No function is related to Down Key; dress.
Use the Righ key to select the next language.
Use the Left key to select the previous language. Function Keys No function is related to F1, F2, F3, F4
keys.
ESC Key Use ESC key to cancel the operation and to
step back to previous page. + Ifgedforbyanymistake,
reason the address of a repeater is chan-
the system will show the message
ENTER Key ENTER Key accepts the selection. of the Figure 51, in this case the address of the re-
peater will be changed using the ESC key.
Function Keys No function is related to F1, F2, F3, F4
keys.
NETWORK Configuration
FC500REP Repeater Address Two ways are available to enrol the Network:
from the Repeater panel ONLY first:
1- the Master Control panel can do the Enrolling (autolear-
After the FC500 control panel has been connected, at ning) after one or more Slave Control panels and one or
the first start-up the FC500REP will verify the presence more Repeaters have been enabled in the network (see
of the address and its conformity. If the address is cor- previous paragraphs);
rect, the Repeater will start to work; on the contrary 1a- use the 1 Key to enroll (see page 47);
1b- use the "Upload from board" key (Software FireClass500
console) in the Master control panel;
second:
2- Use the Software (FireClass500 console) to insert one
This symbol shows the presence
of the connection between the or more Slave Control panels (from Master control panel);
User interface and the main Board.
Control panel Status The symbol KO will be shown
when the connection fails.
2a- Use the "General Options" section (FireClass500 con-
Access level
sole) in every Slave control panels to enable the Slave pa-
System lev.3: PROGRAM nel in the network;
LANGUAGE Master Panel
2b- Use the "General Options" section (FireClass500
ITA eng
^ console) in the Master control Panel to enable the Slave
Language choise Control panels, the Repeaters and the Master control pa-
nel itself in the network .
2c- Use the " Download to board" key.
Figure 50 Page to select the language of the system After the "Auto" Enrolling the system configure the Net-
work devices (Slave control panels and Repeaters) and
besides the Loop devices.
This symbol shows the presence
of the connection between the At the end of the "Auto" Enrolling, the "Master" control
FC500REP repeater the Master
Control Panel and the relative panel can manage the "Slave" control panels and the
address.
Repeaters.
FC500REP REPEATER
Insert the number of the address [1-8]
[_]
!!FAULT!!
Serial link is down
Space to insert the address unable to communicate with the system
press ESC to change repeater address
Figure 51 Display to insert a new FC500REP address Figure 49 Display "the repeater link is down"
These procedure allows the quick start-up of the The panel will start the enrolling procedure. At the end
FC510/520 fire detection system. of this phase will be presented the result of the enrolling
in terms of loop with devices connected (OK) or not
When the loops are wired, electrically verified and all (KO) and it will be possible view the details for each acti-
the devices have been programmed with their related ve loop (number of detectors, number of modules, cur-
address (using the special FC490ST Loop Service Tool) rent drawn), pressing the key [ESC] it is possible to
and installed to the loop, it is possible to connect the lo- reach again the main page.
ops terminals to the panel.
+ Ifredtheloopenrolling result differ from the previously sto-
+ Before powering-on the Fire control panel, ensure
that the Earth Line has been connected.
configuration a warning message will be di-
splayed and it is possible to reject the present
enrolling result ,maintaining the previous configura-
! Be sure that the main voltage is the same of the
input voltage set on the BAQ140T24 power
tion, or accept them.Suddenly after the enrolling
phase the panel starts the loops initialization phase.
supplier. Move the switch 35a if the BAQ140T24
input voltage is different from the main voltage, At the end of this phase, which duration is related to the
ONLY when the power supplier is not connec- number and type of the devices connected over the lo-
ted to the main power. Please note that the po- ops, the panel it is able to act according the directive of
wer supplier will be damaged if it is connected the EN54-2 standard.
to the 230 V main power when it is set for 110 V.
+ The enrolling function will not be activated if there
are present loop related faults.
PROCEDURE
The functional parameters of the panel and devices at
1. Power-on the panel the end of the enrolling procedure are listed below
At this point the panel will start the first system initializa- FC400P: standard mode, medium sensitivity
tion verifying the loops integrity, warming up the smoke
sensor circuitry, looking for not address programmed FC400PH: (temp. = A2S) + (Smoke = standard mode,
devices over the loops and searching devices with the medium sensitivity).
same address.
FC400CH: (temp. = A2S) + (Carbon Monoxide = stan-
+ NOTE: The panel in this phase is configured to ma-
nage closed loops (4 wires loop), if it is connected
dard mode, normal sensitivity).
n Panel outputs
“NAC FIRE” (output EN54-2 type C) active on alarm
event
n Conventional zone
Active,
pre-alarm on detector activation (680 W load),
Day mode
Loop configuration: 4 wires
The following is a list of accessories for control panel in FC400H or FC460H - Addressable Heat Detector
the FC500 series, with a description of the main featu-
res. For further information about these accessories, The FC400H heat detector forms part of the FC400 Se-
please refer to the instructions supplied with the acces- ries of Addressable Fire detectors.The detector is inten-
sories themselves or download them from the FireClass ded to plug into the following:
website: http://www.fireclass.net. Ø 5B 5”Universal Base
Ø FC450IB 5” Isolator Base
FC500IP - IP Module Ø FC430SB Low Power Sounder Base
Software within the controller is used to interpret the re-
The FC500IP is an IP Module which is used to connect turned heat values to raise an alarm or other appropria-
control units in the FC500 range to a LAN. te response according to the type of detector configured
The IP Module may be connected to a LAN using a pri- in Fire Class 500 Console.
vate IP address or a DHCP address. The mode of detector may be:
The same procedures may be performed using the Fi- Ø EN54-5 A1R, rate-of-rise normal ambient
o
reClass500 console application, either through the Ø EN54-5 A2S, fixed 60 C
serial port or the network. With a public IP address, it is Ø EN54-5 CR, rate-of-rise high ambient.
also possible to manage and monitor the control unit
form anywhere in the world, as long as you have access FC400P or FC460P - Addressable Optical
to the Internet. Smoke
FC500PSTN - Telecom Module The FC400P optical smoke detector forms part of the
FC400 Series Addressable Fire detectors.
FC500PSTN is a Telecom Module which allows implemen- Ø FC450IB Isolator Base
ting the functions of Channel Telephone Dialler and Telemo- Ø 5B 5” Universal Base
nitoring (functions E and J of standard EN54-1:1996), within
the control panels of the FC500 series. Software within the controller is used to interpret the re-
General features: turned optical and heat values to raise alarm or other
Ø Possibility of associating up to 3 voice messages for appropriate response according to the type of detector
each event. configured in Fire Class 500 Console.
Ø Built-in multiprotocol digital communicator.
Ø 32 programmable telephone numbers. FC400PH or FC460PH - Addressable
Ø Programming by PC. Optical Smoke & Heat Detector
Ø Check for telephone line cutting.
Ø Excluded line tone check. The FC400PH optical smoke and heat detector forms
Ø Overvoltage protection. part of the FC400 Series of Addressable Fire detec-
Ø Digital message recording playback. tors.The detector is intended to plug into one of the fol-
Ø Built-in speaker for message playback. lowing:
Ø 5B 5” Universal Base
4B - Universal Base Ø FC450IB 5” Isolator Base
Software within the controller is used to interpret the re-
The 4B Universal base is for use with the turned optical and heat values to raise alarm or other
FC460/FC400/600 series of detectors. appropriate response according to the type of detector
The base may be fixed directly to: configured in Fire Class 500 Console. The mode of de-
Ø British (fixing centres 50mm) or European (fixing tector may be:
centres 70mm) conduit box; Ø Mode 1 - Optical smoke only detector (sensitivity
Ø Euro Mounting Box AB-EM; High, Normal or Low)
Ø suspended ceiling, via the CTA adapter; Ø Mode 2 - Optical ( sensitivity High,
o
Normal or Low )
Ø Directly to the ceiling. and heat fixed temperature 60 C (A2S)
Ø Mode 3 - Heat only rate-of-rise (A1R) detector (no
sensitivity selection) o
Ø Mode 4 - Heat fixed temperature 60 C (A2S) (no sen-
sitivity selection)
ACCESSORY 55
4B-I - Isolator Base FC410DIM - Detector Input Module
The FC400/FC460 Series Detectors, as supplied, use a The Addressable FC410DIM provides the ability to con-
common 4B-I Isolator Base assembly. nect and Interface one or two zones of 24V dc 2-wire
The base may be fixed directly to: conventional detectors (non-addressable) to the Fire
Ø British (fixing centres 50mm) or European (fixing Alarm Controller.
centres 70mm) conduit box; The FC410DIM monitors the status of detectors and wi-
Ø Euro Mounting Box AB-EM; ring to detectors and signals detector and wiring status
Ø suspended ceiling, via the CTA adapter; back to the Controller.
Ø Directly to the ceiling.
FC410RIM - Relay Interface Module
FC490ST - Loop Service Tool
The FC410RIM Relay Interface Module provides one
The FC490ST Loop Service Tool is used to program volt-free relay changeover contact on a latching relay. The
the loop address into FC addressable devices. The relay is controlled by a command sent from the FC fire
FC490ST displays information and performs tests on controller via the addressable loop. The relay state (acti-
devices. It has a 32 character backlit LCD alphanume- vated, deactivated or stuck) is returned to the controller.
ric display, arranged in 2 rows of 16 characters and
four ‘softkeys’, F1, F2, F3 and F4. Power for the FC400CH - Addressable Carbon Monoxide
FC490ST is derived from 4 AA size nickel metal hydri- + Heat Detector
de rechargeable batteries. It may be run from an unre-
gulated +12V dc input ie, car cigarette lighter The FC400CH carbon monoxide plus heat detector forms
connection or 110/230V ac mains adaptor, both of part of the FC400 Series Addressable Fire detectors.
which will recharge the batteries as well. The detector is intended to plug into the following:
Ø 5B 5” Universal Base.
FC410BDM - Beam Detector Module Ø FC450IB 5” Isolator Base.
Ø FC430SB Low Power Sounder Base.
The FC410BDM Beam Detector Interface Module is de- The detector is designed to transmit, to a remote Fire
signed to interface FIRERAY 50 Beam Detectors to the Class controller, digital signals which represent status of
FC Digital Addressable Loop (it must not be used with the carbon monoxide and heat elements of the detector.
other types of beam detector). The FC410BDM moni- Software within the controller is used to interpret the re-
tors the Fire and Fault contacts and also monitors for turned carbon monoxide and heat values to raise alarm
open and short circuits on the connections between the or other appropriate response according to the type of
interface and the beam detector. For remote siting of detector configured in Fire Class 500 Console.
the FIRERAY 50 an optional BTM800 Terminal Module
can be used with 4 core cable. 801RIL - Remote LED Indicator
The FIRERAY 50 transmitter and receiver units are mo-
unted in the same housing. The 801RIL Remote Indicator is used where a detector
The FC410BDM Loop Powered Beam Detector Interfa- LED is not visible ie, when the detector is mounted in a
ce Module is contained on a double sided printed circuit roof void, lift shaft etc.The 801RIL is mounted to a single
board (PCB) which is fitted into a custom built fascia gang electrical box and is supplied with 2 x M3.5 screws.
plate with a protective cover being fitted over the PCB,
leaving only the connection terminals exposed. The fa- 801HL - Remote LED Indicator
scia plate is then fitted onto a standard dual-gang back
box with BESA fittings. The 801HL Remote Indicator is used where a detector
LED is not visible ie, when the detector is mounted in a
FC410CIM - Contact Input Module roof void, lift shaft etc.
The 801HL provides a larger indicator for use in place of
The FC410CIM FC Addressable Contact Input Module the 801RIL when longer distances are involved or in
is designed to monitor fire contacts such as extingui- VdS influenced markets.
shing system control, ventilation control, fire door con- The 801HL can be mounted to any suitable flat surface
trol etc. The FC410CIM can be configured as: and has fixing centres at 60 and 80mm.
Ø Two spur circuits (Class B) monitoring multiple nor-
mally open contacts, with short circuit giving a fault HVR800-High Voltage Relay
output.
Ø Two spur circuits (Class B) monitoring single nor- The HVR800 High Voltage Relay Interface is a non-ad-
mally closed contacts, with short circuit giving a fault dressable multi-voltage relay module (operating from
output. 24V dc, 24V ac, 120V ac and 240V ac).
Ø Two spur circuits (Class B) monitoring multiple nor- The encapsulated HVR800 provides a 10 amp volt-free
mally open contacts, with short circuit giving an alarm. contact that can be used to extend the contact ratings of
FC410RIM Addressable Relay Module applications.
A maximum of four HVR800s can be individually driven
ACCESSORY 57
FC410QIO Quad input output module FC410LPAV: Sounder-Beacon IP65 (outdoor use) - red
housing
The module provides four monitored digital inputs and The sounder has two volume settings ‘High’ (103 dB ±3)
four potential free relay changeover outputs. or ‘Low’ (90 dB ±3).
The outputs are monitored with parallel contacts of the The beacon has two flash rates ‘Slow Flash’ (1/2 Hz) or
relays. The outputs can be connected to an Auxiliary ‘Fast Flash’ (1 Hz).
Voltage source and its voltage can be monitored. The FC410LPBS devices are synchronised, but not
Additionally, all the outputs can be connected to the synchronous with other FireClass sounders and beacons
HVR800, for switching high power galvanic isolated loads. of the FC400 serie.
For more details refer to the HVR800 documentation. The first flash of the beacon is synchronised with the start
The module has an integral loop isolator. If this activa- of the tone.
tes a yellow LED illuminates. The activation remains in The FC410LPBS devices have a built in two port isolator.
place until the short is removed.
The digital input monitoring and isolator functions are FC430LPBSB Loop Powered Addressable
both configurable. Sounder/Beacon Base (EN54-23)
Maximum relay current: 2A.
Maximum relay voltage: 30V. The FC430LPBS Series of Loop Powered Addressable
Sounder/Sounder- Beacons are designed to be driven
FC410QRM Quad relay module
from an FC501 control panel via the addressable loop.
The module provides four potential free relay changeo- Tone, volume and flash rates are set in FireClass Console.
ver outputs. The outputs are monitored, with parallel The sounder has four volume settings ‘High’ (90dB ±3),
contacts of the relays. The outputs can be connected to ‘Mid High’ (80 ±3dB), ‘Mid Low’ (70 ±3dB)or ‘Low’ (60dB
an Auxiliary Voltage source and its voltage can be mo- ±3). The beacon has two flash rates ‘Slow Flash’
nitored. (1/2Hz) or ‘Fast Flash’ (1Hz).
Additionally, all the outputs are configurable to the HVR The FC430LPBS Series have a built-in line isolator.
(High Voltage Relay) mode, which allows you to con-
nect up to four HVR800 modules for switching; for The table below, cross connect the managed devices in
example 240V loads galvanically isolated. the current version and the new EN54-23.
The module has an integral loop isolator. If this activa-
tes a yellow LED illuminates. The activation remains in
place until the short is removed.
+ Itspondent
is possible to substitute old devices with corre-
new ones (EN54-23), keeping the same
Maximum relay current: 2A. program data. When the old device is physically re-
Maximum relay voltage: 30V. moved from the loop, the control panel will signal
the "No answer" fault. When the new device with
the same address is connected to the loop, the
FC410LPBS-R/W loop powered sounders control panel will restore the "No answer" fault and
and sounder-beacons (EN54-23) automatically update its internal database with the
new device type.
The FC410LPBS Series of Loop Powered Addressable It is not possible to substitute new devices
Sounder/ Sounder-Beacons are designed to be driven (EN54-23) with old ones (they are not EN54-23 ap-
from a FC501 control panel via the addressable loop. proved).
The FC410LPBS Series of sounders/sounder beacons
consist:
FC410LPBS-R: Sounder (indoor use) - red housing
FC410LPBS-W: Sounder (indoor use) - white housing
FireClass FireClass
FireClass Product FireClass Device
Description Product code Device name
code (Current Dev.) name (Current Dev.)
(EN54-23 Dev.) (EN54-23 Dev.)
Loop Powered Beacon
516.800.758 FC430LPASB 516.800.973 FC430LPBSB
Sounder Base
Loop Powered
516.800.763 FC410LPAVR FC410LPBS-R
Beacon/Sounder (indoor use) 516.800.970
red
Loop Powered
516.800.764 FC410LPAVW 516.800.971 FC410LPBS-W
Beacon/Sounder (indoor use)
white
Loop Powered
FC410LPBS
516.800.766 FC410LPAV Beacon/Sounder IP65 516.800.972
(outdoor use)
This quick guide is for installers with knowledge of the The following table shows the technical features of the
control panels, and fire control panels in general. This Repeater FC500REP.
chapter holds all the necessary installation details.
REPEATER FC500REP
Main voltage 27,6 V
Technical features Maximum current 180 mA
Temperature range -5 ÷ +40°
Some of the technical features, regarding the terminals Dimensions (W*H*D) 390x215x50 mm
on the Main, are described in the following paragraph. Weight 2,05 Kg
QUICK GUIDE 59
TERM. DESCRIPTION v(V) i(A)
MAIN BOARDS
+L1- (+)Loop 1-Positive signal, left side. — —
LEFT (-)Loop 1-Negative signal (return), left side
+L1- (+)Loop 1-Positive signal, right side. — —
RIGHT (-)Loop 1-Negative signal (return), right side
+L2- (+)Loop 2-Positive signal, left side.
— —
LEFT (-)Loop 2-Negative signal (return), left side.
+L2- (+)Loop 2-Positive signal, right side.
— —
RIGHT (-)Loop 2-Negative signal (return), right side.
CONVENTIONAL LINE:
balanced line with 3900 ohm è control panel in standby
[LC]
unbalanced line è Conventional Zone activated
— —
line in short-circuit or open è fault on the Conventional Zone
[M] Ground 0 —
+485- SERIAL BUS. Terminals to connect the FC500REP and SLAVE control Panel — —
24 V POWER Output for the FC500REP and SLAVE control Panel:
[M] 27,6 0,5(1)
Positive pull-up to 27.6 V on [24V] terminal
[24V] 0 —
Negative pull-down to 0 V on [M] terminal
24 V AUXILIARY POWER SUPPLY:
0
[AUX] negative present on terminal [M];
27,6 0,5(1)
positive present on terminal [24A].
24 V AUXILIARY POWER SUPPLY:
[AUX- 0
negative present on terminal [M];
RES] 27,6 0,5(1)
positive present on terminal [24A].
[NC]
FIRE ALARM OUTPUT - Non-Supervised:
[NO]
standby è [C] connected to [NC] with [NO] open;
[C]
in the event of ALARM è [C] connected to [NO] with [NC] open — —
FIRE
[NC]
FAULT ALARM OUTPUT - Non-Supervised:
[NO]
standby è [C] connected to [NC] with [NO] open
[C]
in the event of fault è [C] connected to [NO] with [NC] open — —
FAULT
+BAT2- BATTERY CONTROL PANEL POWER SUPPLY 27,6
+BAT1- BATTERY CONTROL PANEL POWER SUPPLY 27,6
[OS1]... Programmable Outputs(Open collector)- Silenceable-Bypassable (Disabled)-Supervised
27,6
[OS8] (The polarity is not programmable)
Programmable Outputs(Open collector)- Silenceable-Bypassable (Disabled)-NOT
[O9]...
Supervised
[O16] 0 1
(The polarity is not programmable)
Type C output (EN54-1) - Silenceable, Bypassable (Disabled), Supervised
-NAC
Terminals for supervised devices activated by positive (24 V):
FIRE+ 27,6
During ALARM status —— positive (27.6 V) on terminal [+]; negative on terminal [-].
[NAC1] Programmable—Supervised—Silenceable—Bypassable (Disabled) ALARM Outputs:
[NAC2] Panel in Standby è negative on [+] terminal; positive 27.6V on [–] terminal
(2)
[NAC3] Panel in Alarm è positive 27.6V on [+] terminal; negative 0 V on [–] terminal —
12 V AUXILIARY POWER SUPPLY:
[12V] on [12V] terminal è positive 13,8
—
on [M] terminal è negative 0
© FireClass