Professional Documents
Culture Documents
CDJ-1000MK3
Operating Instructions
Manual de instrucciones
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory
drawings. However the method of connecting and operating the unit is the same. K015 En
WARNING
IMPORTANT This equipment is not waterproof. To prevent a fire
CAUTION or shock hazard, do not place any container filed
with liquid near this equipment (such as a vase or
RISK OF ELECTRIC SHOCK
DO NOT OPEN flower pot) or expose it to dripping, splashing, rain
or moisture. D3-4-2-1-3_A_En
The lightning flash with arrowhead symbol, CAUTION: The exclamation point within an equilateral
within an equilateral triangle, is intended to TO PREVENT THE RISK OF ELECTRIC triangle is intended to alert the user to the WARNING
alert the user to the presence of uninsulated SHOCK, DO NOT REMOVE COVER (OR presence of important operating and Before plugging in for the first time, read the following
"dangerous voltage" within the product's BACK). NO USER-SERVICEABLE PARTS maintenance (servicing) instructions in the
enclosure that may be of sufficient INSIDE. REFER SERVICING TO QUALIFIED literature accompanying the appliance.
section carefully.
magnitude to constitute a risk of electric SERVICE PERSONNEL. The voltage of the available power supply differs
shock to persons. according to country or region. Be sure that the
D3-4-2-1-1_En-A
power supply voltage of the area where this unit
CAUTION will be used meets the required voltage (e.g., 230V
This product is a class 1 laser product, but this or 120V) written on the rear panel. D3-4-2-1-4_A_En
CAUTION : USE OF CONTROLS OR ADJUSTMENTS If the AC plug of this unit does not match the AC
OR PERFORMANCE OF PROCEDURES outlet you want to use, the plug must be removed
OTHER THAN THOSE SPECIFIED and appropriate one fitted. Replacement and POWER-CORD CAUTION
HEREIN MAY RESULT IN HAZARDOUS mounting of an AC plug on the power supply cord of Handle the power cord by the plug. Do not pull out the
RADIATION EXPOSURE. this unit should be performed only by qualified plug by tugging the cord and never touch the power
CAUTION : THE USE OF OPTICAL INSTRUMENTS service personnel. If connected to an AC outlet, the cord when your hands are wet as this could cause a
WITH THIS PRODUCT WILL INCREASE cut-off plug can cause severe electrical shock. Make short circuit or electric shock. Do not place the unit, a
EYE HAZARD. D6-8-2-1_En sure it is properly disposed of after removal. piece of furniture, etc., on the power cord, or pinch the
The equipment should be disconnected by removing cord. Never make a knot in the cord or tie it with other
the mains plug from the wall socket when left cords. The power cords should be routed such that they
Information to User
unused for a long period of time (for example, when are not likely to be stepped on. A damaged power cord
Alteration or modifications carried out without
on vacation). can cause a fire or give you an electrical shock. Check
appropriate authorization may invalidate the user’s D3-4-2-2-1a_A_En
the power cord once in a while. When you find it
right to operate the equipment.
D8-10-2_En damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement. S002_En
CAUTION: This product satisfies FCC regulations
when shielded cables and connectors are used to
connect the unit to other equipment. To prevent
electromagnetic interference with electric appliances AC power cord
such as radios and televisions, use shielded cables The type of cord which can be used depends on the power voltage in each region or
and connectors for connections. D8-10-3a_En country. Please make sure you use the correct cord due to the possibility of fire or other
Operating Environment hazard if used incorrectly (see below).
Operating environment temperature and humidity:
+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH
AC power cord and converter plug use
(cooling vents not blocked) Region Plug type
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
For European type region
strong artificial light) D3-4-2-1-7c_A_En Caution
Do not use this power cord set in Taiwan.
CAUTION
The POWER switch on this unit will not completely
shut off all power from the AC outlet. Since the
European two-pin plug
power cord serves as the main disconnect device for
the unit, you will need to unplug it from the AC outlet For Taiwan exclusively
to shut down all power. Therefore, make sure the Caution
unit has been installed so that the power cord can For use in Taiwan only.
be easily unplugged from the AC outlet in case of an In other areas, please do not use.
accident. To avoid fire hazard, the power cord should
also be unplugged from the AC outlet when left Taiwanese two-pin flat-bladed plug
unused for a long period of time (for example, when
on vacation). D3-4-2-2-2a_A_En
2
En <DRB1398>
Enhorabuena por la adquisición de este producto Pioneer.
Lea completamente este manual de instrucciones para aprender a operar correctamente el aparato. Después de haber terminado la
lectura de las instrucciones, guarde el manual en un lugar seguro para poderlo consultar en el futuro.
En algunos países o regiones, la forma de la clavija de alimentación y del enchufe de corriente pueden ser diferentes de la mostrada en
las ilustraciones de explicación. Sin embargo, el método de conexión y operación del aparato es el mismo. K015 Sp
English
IMPORTANTE ADVERTENCIA
Este aparato no es impermeable. Para evitar el
CAUTION riesgo de incendio y de descargas eléctricas, no
RISK OF ELECTRIC SHOCK ponga ningún recipiente lleno de líquido (como
DO NOT OPEN
pueda ser un vaso o un florero) cerca del aparato ni
lo exponga a goteo, salpicaduras, lluvia o
La luz intermitente con el símbolo de punta ATENCIÓN: El punto exclamativo dentro un triángulo
de flecha dentro un triángulo equilátero. PARA PREVENIR EL PELIGRO DE CHOQUE equilátero convenido para avisar el usuário humedad. D3-4-2-1-3_A_Sp
Está convenido para avisar el usuario de la ELÉCTRICO NO REMOVER LA TAPA NI LAS de la presencia de importantes
Español
presencia de “voltaje peligrosa” no aislada PARTES DENTRO NO UTILIZADAS, instrucciones sobre el funcionamiento y la ADVERTENCIA
dentro el producto que podría constituir un LLAMAR UNA PERSONA CUALIFICADA manutención en la libreta que acompaña el
peligro de choque eléctrico para las aparato.
Antes de enchufar el aparato a la corriente, lea la
personas. sección siguiente con mucha atención.
D3-4-2-1-1_Sp
La tensión de la red eléctrica es distinta según el
país o región. Asegúrese de que la tensión de la
PRECAUCIÓN alimentación de la localidad donde se proponga
Este aparato es un producto de láser de clase 1, pero contiene utilizar este aparato corresponda a la tensión
un diodo de láser de clase superior a 1. necesaria (es decir, 230 V ó 120 V) indicada en el
Para mantener la seguridad en todo momento, no quite CLASS 1 panel posterior. D3-4-2-1-4_A_Sp
ninguna cubierta ni intente acceder al interior del aparato.
Solicite todo el servicio técnico a personal cualificado.
LASER PRODUCT ADVERTENCIA
En su aparato encontrará la siguiente etiqueta de precaución. Para evitar el peligro de incendio, no ponga nada
Ubicación: Parte inferior del reproductor con fuego encendido (como pueda ser una vela)
D3-4-2-1-8_A_Sp
encima del aparato. D3-4-2-1-7a_A_Sp
3
<DRB1398> Sp
Contents/Specifications
Contents
Before Operating Advanced Operations
Specifications ........................................................................... 4 Advanced Operations ............................................................. 30
Features ................................................................................... 6 Scratch play ...................................................................... 30
Handling Precautions ............................................................... 8 Spin play ........................................................................... 31
Discs Usable with This Unit ................................................... 10 Braking ............................................................................. 31
Connections ........................................................................... 13 Loop playback ................................................................... 31
Names and Functions of Parts ............................................... 15 To perform hot cue ........................................................... 32
Reverse play ..................................................................... 32
Basic Operations About fader start play ....................................................... 33
Loading and Removing Discs ................................................. 20 Relay play using two players ............................................ 33
DJ Player Operation ............................................................... 22 Operations Using Memory Cards ........................................... 34
Auto cueing ...................................................................... 22 Recording to memory cards ............................................. 35
Starting playback .............................................................. 22 To call up recorded data .................................................... 36
To stop playback ............................................................... 23 To delete information recorded on memory cards ........... 36
To pause playback ............................................................ 23 To copy memory card data ............................................... 37
Fast forward / Fast reverse .............................................. 23 Display during recording of cue and loop points .............. 37
Track search ...................................................................... 24
Folder search (MP3 only) .................................................. 24 Other
Cue point settings ............................................................ 25 Troubleshooting ...................................................................... 38
To change the playing speed ............................................ 26
Applying master tempo .................................................... 27
Jog dial functions ............................................................. 27
Jog sensitivity adjustment ................................................ 28
Mixing different tracks ..................................................... 28
About WAVE display ......................................................... 29
About TEXT display .......................................................... 29
Specifications
1. General 3. Accessories
System ................................ Compact disc digital audio system ÷ Operating instructions ......................................................... 1
Power requirements ..................... AC 110 V to 240 V, 50/60 Hz ÷ Power cord (☞ P. 2) ............................................................. 2
Power consumption .......................................................... 27 W ÷ Audio cable .......................................................................... 1
Operating temperature..................................... +5 °C to +35 °C ÷ Control cord ......................................................................... 1
Operating humidity................................................ 5 % to 85 % ÷ Forced eject pin
(There should be no condensation of moisture.) (housed in a groove in the bottom panel) ............................ 1
Weight .............................................................................. 4.2 kg ÷ SD memory card .................................................................. 1
Dimensions ............................. 320 (W) x 370 (D) x 105 (H) mm
NOTE:
2. Audio section Specifications and design are subject to possible modification
Frequency response .......................................... 4 Hz to 20 kHz without notice.
Signal-to-noise ratio ............................... 115 dB or more (JEITA)
Distortion .......................................................... 0.006 % (JEITA)
4
En <DRB1398>
Índice/Especificaciones
Índice
Antes de la operación Operaciones avanzadas
Especificaciones ....................................................................... 5 Operaciones avanzadas .......................................................... 30
English
Características .......................................................................... 7 Reproducción rascada ...................................................... 30
Precauciones de manejo .......................................................... 9 Reproducción con rotación ............................................... 30
Discos utilizables con esta unidad .......................................... 11 Frenado ............................................................................ 31
Conexiones ............................................................................ 13 Reproducción de bucle ..................................................... 31
Nomenclatura y funciones de las partes ................................ 15 Para realizar la localización rápida ..................................... 32
Reproducción en inversión ............................................... 33
Operaciones básicas Acerca de la reproducción de inicio con fundido .............. 33
Reproducción por relevos con dos reproductores ............ 33
Español
Carga y extracción de discos .................................................. 20
Operación del reproductor para DJ ........................................ 22 Operaciones utilizando tarjetas de memoria .......................... 34
Localización automática .................................................... 22 Grabación en tarjetas de memoria ................................... 35
Inicio de la reproducción ................................................... 22 Para llamar datos grabados .............................................. 36
Para detener la reproducción ............................................ 22 Para borrar la información grabada en tarjetas
Para pausar la reproducción ............................................. 23 de memoria ...................................................................... 36
Avance rápido/inversión rápida ......................................... 23 Para copiar datos de una tarjeta de memoria ................... 37
Búsqueda de pistas .......................................................... 24 Visualización durante la grabación de puntos de
Búsqueda de carpetas (sólo MP3) .................................... 24 localización y de bucle ...................................................... 37
Ajustes de puntos de localización .................................... 24
Para cambiar la velocidad de reproducción ...................... 26 Solución de problemas
Aplicación del tempo principal .......................................... 26 Solución de problemas ........................................................... 39
Funciones del mando de lanzadera .................................. 26
Ajuste de la sensibilidad del mando de lanzadera ............ 28
Mezcla de pistas distintas ................................................ 28
Acerca de la visualización de ondas (WAVE) ..................... 29
Acerca de la visualización de texto (TEXT) ....................... 29
Especificaciones
1. Generalidades 3. Accesorios
Sistema ................... Sistema audiodigital de discos compactos ÷ Manual de instrucciones ...................................................... 1
Alimentación .................................. CA 110 V a 240 V, 50/60 Hz ÷ Cable de alimentación (☞ P. 3) ............................................ 2
Consumo ........................................................................... 27 W ÷ Cable de audio ..................................................................... 1
Temperatura de funcionamiento ......................... +5 ˚C a +35 ˚C ÷ Cable de control ................................................................... 1
Humedad de funcionamiento .................................. 5 % a 85 % ÷ Pasador de expulsión forzada
(No deberá haber humedad de condensación) (colocado en una ranura del panel inferior) .......................... 1
Peso ................................................................................. 4,2 kg ÷ Tarjeta de memoria SD ........................................................ 1
Dimensiones ........................ 320 (An) x 370 (Prf) x 105 (Al) mm
NOTA:
2. Sección de audio Las especificaciones y el diseño están sujetos a cambios sin
Respuesta de frecuencia ...................................... 4 Hz a 20 kHz previo aviso con motivos de mejoras.
Relación señal a ruido ........................... Más de 115 dB (JEITA)
Distorsión ......................................................... 0,006 % (JEITA)
5
<DRB1398> Sp
Features
Features
The CDJ-1000MK3 compact disc player is designed for use by ¶ TEMPO CONTROL RANGE
DJs providing all the functions and performance required in disco The maximum variable range can be set to four variable ranges:
clubs while offering performance, sound quality and functional- ±6 %, ±10 %, ±16 % and WIDE to facilitate adjustment.
ity superior to any analog player. ¶ TEMPO CONTROL RESET
Resets the tempo to 0 % regardless of slider position.
JOG DIAL ¶ MASTER TEMPO
Changes music tempo without changing pitch.
The large 206 mm diameter jog dial enables better handling
than an analog turntable.
¶ PITCH BEND CUE
This function changes the music tempo depending on direction ¶ BACK CUE
of jog dial rotation and speed of movement. After storing the cue point in memory, press the CUE button
¶ SCRATCH PLAY while playing the unit to go back to the cue point and start over.
In the VINYL mode when the surface of the jog dial is pressed ¶ AUTO CUE
playback is discontinued and then continues according to the Auto cue automatically locates the song’s start point even if it
direction and speed the dial is rotated. You can also adjust the differs from the track’s frame, allowing the player to start in-
startup when the jog dial is touched and released to create new stantly at a press of the PLAY button.
DJ techniques. ¶ CUE POINT SAMPLER
¶ FRAME SEARCH The sound from the memorized cue point can be reproduced by
Moves the disc from pause position in frame increments (1/75 one touch, which can be used as the start point check and the
sec) when the jog dial is rotated in pause mode. sampler.
¶ SUPER FAST SEARCH
Rotate the jog dial while holding depressed the SEARCH button, REAL TIME SEAMLESS LOOP
TRACK SEARCH button, or FOLDER SEARCH button. When this
This function simplifies setting and releasing loops. This func-
is done, search will be performed faster than the normal search,
tion lets you set a loop while you are playing a track. A loop can
track search, or folder search operations.
also be set at the end of the track so that the track does not
¶ JOG ADJUST (Jog Sensitivity Adjustment)
stop. In addition, an ADJUST mode has been added to enable
This function allows you to adjust the felt resistance when rotat-
one-touch adjustments to Loop-in and Loop-out points and facili-
ing the jog dial.
tate loop operation.
6
En <DRB1398>
Before Operating
Características
(Features)
Características
El reproductor de discos compactos CDJ-1000MK3 está diseñado para ¶ MARGEN DE CONTROL DEL RITMO
que lo empleen DJ, ofreciéndoles todas las funciones y operaciones El margen máximo variable puede ajustarse en cuatro márgenes vari-
English
necesarias para emplearlo en discotecas con un rendimiento, calidad de ables: ±6 %, ±10 %, ±16 % y WIDE para facilitar el ajuste.
sonido y funcionalidad superiores a cualquier reproductor analógico. ¶ REPOSICIÓN DEL CONTROL DEL RITMO
Repone el ritmo al 0 % independientemente de la posición del control
MANDO DE LANZADERA deslizante.
¶ RITMO PRINCIPAL
El mando de lanzadera de diámetro grande, de 206 mm, permite
Cambia el ritmo de la música sin cambiar el tono.
una mejor manipulación que un giradiscos analógico.
¶ INFLEXIÓN DEL TONO
Esta función cambia el ritmo de la música dependiendo de la dirección LOCALIZACIÓN
de rotación del mando de lanzadera y de la velocidad de movimiento. ¶ LOCALIZACIÓN REGRESIVA
Español
¶ REPRODUCCIÓN RASCADA Después de haber memorizado el punto de localización, presione el botón
En el modo VINYL, cuando se presiona la superficie del mando de de localización (CUE) mientras se reproduce la música para volver al punto
lanzadera, se interrumpe la reproducción y luego continúa de acuerdo de localización y volver a empezar desde ahí.
con la dirección y velocidad con la que se gira el mando. También podrá ¶ LOCALIZACIÓN AUTOMÁTICA
ajustar el inicio cuando se acciona y suelta el mando de lanzadera para La función de localización automática encuentra automáticamente el
crear nuevas técnicas de DJ. punto de inicio de la canción aunque sea distinto de la trama de la canción,
¶ BÚSQUEDA POR TRAMAS para que el reproductor pueda comenzar instantáneamente al presionar
Mueve el disco desde la posición de pausa en incremento de tramas el botón de reproducción (PLAY).
(1/75 de seg.) cuando se gira el mando de lanzadera en el modo de pausa. ¶ MUESTREADOR DEL PUNTO DE LOCALIZACIÓN
¶ BÚSQUEDA SÚPER RÁPIDA El sonido del punto de localización memorizado puede reproducirse
Gire el mando de lanzadera manteniendo presionado el botón SEARCH, mediante un accionamiento, y puede utilizarse como comprobación del
el botón TRACK SEARCH, o el botón FOLDER SEARCH. Cuando lo haga, punto de inicio y muestreador.
la búsqueda se realizará con mayor rapidez que durante las operaciones
de búsqueda normal, búsqueda de pistas o de búsqueda de carpetas.
BUCLE CONTINUO EN TIEMPO REAL
¶ AJUSTE DEL MANDO DE LANZADERA (Ajuste de la sensibilidad
del mando) Esta función simplifica el establecimiento y desactivación de bucles. Esta
Esta función le permitirá ajustar la resistencia que se nota al girar el mando función le permite establecer un bucle mientras está reproduciendo una
de lanzadera. canción. También podrá establecer un bucle al final de la canción para
que la canción no se detenga. Adicionalmente, se ha añadido un modo
de ajuste (ADJUST) para permitir ajustes de un accionamiento para los
VISUALIZADOR DEL MANDO DE puntos de entrada y salida de bucle y para facilitar la operación con bucles.
LANZADERA
En el centro del mando de lanzadera se visualiza información relacionada REPETICIÓN DE BUCLES
con el estado del disco, posición del punto de localización, estado de la Le permite reproducir repetidamente un bucle las veces que desee.
memoria de sonido, detección de accionamiento del mando de lanzadera, Presione el botón de repetición (RELOOP) de bucle después de desactivar
y el modo VINYL. la reproducción de bucle para volver al punto de inicio del bucle. El empleo
perspicaz de la activación y desactivación en combinación con el ritmo
VISUALIZADOR DE ONDAS hará posible la creación de nuevos efectos sonoros.
LECTURA MÚLTIPLE
REPRODUCCIÓN HACIA ATRÁS
Permite la reproducción de discos CD-R y CD-RW (grabados en el formato
Ajuste el selector de dirección (DIRECTION) en la posición de avance CD de audio o MP3). (Tenga presente que es posible que algunos discos
(posición [REV]) para reproducir la música hacia atrás. no se reproduzcan correctamente debido a las características de los dis-
cos individuales, de la grabadora, o a suciedad y rayadas en los discos.)
CONTROL DEL RITMO
El control deslizante de 100 mm de alta precisión acoplado con un REPRODUCCIÓN DJ DE ARCHIVOS MP3
visualizador digital de incrementos del 0,02 % (dentro de un margen de Los archivos MP3 grabados en discos CD-ROM pueden reproducirse
±6 %) permite el control exacto de la velocidad para que el ajuste del con las funciones de DJ.
ritmo sea fácil y preciso.
7
<DRB1398> Sp
Handling Precautions
Handling Precautions
Installation location Moving the unit
¶ Placing and using the player for long periods on heat-generat- ■ Never move the unit during playback!
ing sources such as amplifiers or near spotlights, etc. will af- During playback, a disc rotates at very high speed; moving the
fect product performance. Avoid placing the player on heat- player during playback may result in scratches or other damage
generating sources. to the disc.
¶ Install this player as far as possible away from tuners and TV
sets. The player installed in close proximity to such equip- ■ When moving the unit is necessary
ment may cause noise or degradation of the picture. Before moving the unit, remove any disc and disconnect the
Noise may be noticeable when an indoor antenna is used. In power. Malfunctions or damage may result if the unit is moved
such cases, make use of an outdoor antenna or turn off power with a disc loaded.
to the player.
¶ When the unit is used in a loud-sound environment, e.g., near About the carrying case
a speaker, sound skip may occur. Install the unit away from
The upper surface of the jog dial is equipped with a touch-sensi-
the speaker or reduce the listening volume.
tive switch. When placing the player in its carrying case, avoid
¶ Place this unit on a level surface and a stable platform.
placing any pressure on the jog dial.
Take adequate note of the following precautions when pre-
paring a place for installation:
Condensation
Be sure the player, including its video, audio and power supply
cords, does not touch vibrating materials. Any vibration other When this unit is brought into a warm room from previously cold
than that transmitted through the insulators may cause the disc surroundings or when the room temperature rises sharply, con-
to skip. Take special care when using the player while it is in- densation may form inside the unit and impair its performance.
stalled in a carrying case. In such cases, allow the unit to stand for about an hour or raise
the room temperature gradually.
8
En <DRB1398>
Before OperatingPrecauciones
(Handling Precautions)
de manejo
Precauciones de manejo
Lugar de instalación Movimiento de la unidad
¶ La colocación y utilización del reproductor durante mucho tiempo ■ ¡No mueva nunca la unidad durante la
English
sobre fuentes de generación de calor, tales como amplificadores, reproducción!
o cerca de lámparas, etc. Afectará el rendimiento del reproductor. Durante la reproducción, el disco girará a velocidad muy alta. Si
Evite colocar el reproductor sobre fuentes que generan calor. moviese el reproductor durante la reproducción, el disco podría
¶ Instale este reproductor lo más alejado posible de sintonizadores rayarse o sufrir otros daños.
y televisores. Si lo instalase cerca de tales equipos, podría
producirse ruido y la degradación de las imágenes. Esto puede ■ Cuando sea necesario mover la unidad
notarse más cuando se utilice una antena interior. En tales casos, Antes de mover la unidad, extráigale el disco y desconecte la
utilice una antena exterior o desconecte la alimentación del
Español
alimentación. Si moviese la unidad con un disco cargado, podrían
reproductor. producirse daños.
¶ Si utiliza la unidad en un ambiente ruidoso, por ejemplo, cerca
de un altavoz, es posible que se produzca salto de sonido. En Acerca de la caja de transporte
tal caso, instale la unidad separada del altavoz, o reduzca el
nivel de escucha. La superficie superior del mando de lanzadera está equipada con un
¶ Coloque este aparato sobre una superficie plana y estable. interruptor sensible al tacto. Cuando coloque el reproductor en su
Tenga en cuenta las precauciones siguientes cuando prepare caja de transporte, evite aplicar presión sobre el mando de lanzadera.
un lugar para la instalación:
Condensación
Asegúrese de que el reproductor, incluyendo sus cables de au-
dio y de alimentación eléctrica, no toquen materiales que vibren. Cuando el reproductor se desplaza de un lugar frío a otro cálido, o
Las vibraciones que los aisladores no puedan absorber podrán cuando la temperatura de la sala aumenta repentinamente, puede
ser la causa de que salte el disco. Tenga cuidado especial cuando condensarse humedad en el interior, y es posible que el reproductor
utilice el reproductor mientras está instalado en una caja para el no rinda al máximo. En tal caso, deje el reproductor en reposo du-
transporte. rante una hora o aumente gradualmente la temperatura de la sala.
9
<DRB1398> Sp
Discs Usable with This Unit (Types of discs playable on this unit/Playing MP3 files)
MP3 format MPEG-1 Supports Audio Layer-3 sampling frequency 32 kHz, 44.1 kHz, 48 kHz,
Bit Rate 32 Kbps to 320 Kbps.
MPEG-2 Supports Audio Layer-3 sampling frequency 16 kHz, 22.05 kHz, 24 kHz,
Bit Rate 16 Kbps (stereo) to 160 Kbps.
ID3 tag Supports ID3 Vers. 1.0/1.1/2.2/2.3/2.4.
Displays title, album, artist.
Disc format File extension .mp3, .MP3, .mP3, .Mp3
Folder layers Maximum 8 layers; files in folders exceeding 8 layers cannot be
played.
Maximum number of folders 99 (99 folders + 1 root)
Maximum number of files 999 (per folder)
CD-R recording method Record following the ISO9660 CD-ROM file system.
Supports only Disc At Once or Track At Once.
CDJ-1000MK3 does not support Packet Write recorded discs.
* CDJ-1000MK3 is not equipped with a File Sort function; tracks will be played in the order in which they were recorded.
* Plays MP3 files stored on CD-ROM. Cannot play MP3 files stored on SD memory cards or MultiMedia cards (MMC).
* Startup time increases with the number of folders.
10
En <DRB1398>
Discos utilizables con esta unidad (Tipos de discos reproducibles en esta unidad/Reproducción de archivos MP3)
English
etiquetas, las envolturas, o las fundas de los discos. autónomas o unidades de ordenador pueden no reproducirse
en este reproductor debido a gran variedad de razones, como
Tipos y logotipos de los discos reproducibles las características de los discos, rayas, suciedad, suciedad en
el objetivo del reproductor, condensación de humedad, etc.
CD CD-TEXT (Nota 1) CD-R (Nota 2) CD-RW (Nota 2)
¶ Algunos discos grabados en unidades de ordenador pueden
no reproducirse en este reproductor dependiendo de la
aplicación de grabación utilizada, los ajustes, y el entorno de
operación. Cerciórese de utilizar el formato correcto para los
Español
discos que use. Con respecto a los detalles, consulte al autor
Nota 1) Acerca de la visualización de TEXT: de la aplicación.
El número de caracteres que podrán visualizarse es de un máximo ¶ Este reproductor no podrá reproducir discos CD-R ni CD-RW
de 48. Cuando una visualización sobrepase 16 caracteres, ésta parcialmente grabados que no se hayan finalizado.
se desplazará. Solamente podrán visualizarse caracteres ¶ Con respecto a la información detallada sobre el manejo de
alfanuméricos y un número limitado de símbolos (☞ P. 29) los discos CD-R/CD-RW, consulte las precauciones de manejo
suministradas con cada disco.
Nota 2) Acerca de los discos CD-R/CD-RW:
Este reproductor puede reproducir discos CD-R/CD-RW grabados
en el formato CD de audio o MP3. ■ Acerca de los discos CD-R/RW
* Con respecto a los detalles, consulte el Manual de Debido a la fabricación particular de los discos CD-R/RW, si se
instrucciones de su grabadora. dejan durante períodos prolongados de tiempo en el estado de
pausa (o de espera de localización) en un mismo punto, es posible
Para reproducir discos CD de 8 cm, utilice siempre un adaptador que se dificulte la reproducción del disco en dicho lugar. Puede
para discos CD de 8 cm (☞ P. 21). producirse el mismo síntoma si se emplea la función de bucle
para reproducir excesivamente un mismo punto del disco.
Como resultado, se aconseja a los usuarios que creen discos de
copia de seguridad cuando reproduzcan discos que contengan
datos importantes.
Formato MP3 MPEG-1 Compatible con Audio Layer-3 con frecuencias de muestreo de
32 kHz, 44,1 kHz, 48 kHz, y velocidad en bits de 32 Kbps a 320 Kbps.
MPEG-2 Compatible con Audio Layer-3 con frecuencias de muestreo de 16
kHz, 22,05 kHz, 24 kHz, y velocidad en bits de 16 Kbps (estéreo) a 160
Kbps.
Etiqueta ID3 Es compatible con ID3 de las versiones 1.0/1.1/2.2/2.3/2.4.
Visualiza el título, el álbum, y el artista.
Formato del disco Extensión de archivo .mp3, .MP3, .mP3, .Mp3
Capas de carpetas Máximo de 8 capas; los archivos ubicados en carpetas que exceden
de 8 capas no pueden reproducirse.
Número máximo de carpetas 99 (99 carpetas + 1 de raíz)
Número máximo de archivos 999 (por carpeta)
Método de grabación de discos Grabe según el sistema de archivos de CD-ROM ISO9660.
CD-R Sólo es compatible con “Disc At Once” o “Track At Once”.
El CDJ-1000MK3 no es compatible con discos grabados con el
método de escritura por paquetes.
* El CDJ-1000MK3 no está equipado de una función de clasificación de archivos; las pistas se reproducirán en el orden con el que
fueron grabadas.
* Reproduce los archivos MP3 almacenados en el CD-ROM. No puede reproducir los archivos MP3 grabados en tarjetas de
memoria SD ni en tarjetas MultiMedia (MMC).
* El tiempo de inicio aumenta según el número de carpetas.
11
<DRB1398> Sp
Discs Usable with This Unit (Handling discs)/Discos utilizables con esta unidad (Manejo de los discos)
■ Discs rotate at high speeds inside the player. Do not use dam-
aged, cracked or warped discs. ■ Los discos giran a gran velocidad dentro del reproductor. No
emple discos dañados, rajados o alabeados.
■ Storing discs
¶ Discs are made of the same kinds of plastic used for conven- ■ Almacenamiento de los discos
tional analog audio records. Be careful not to allow discs to warp. ¶ Los discos están hechos del mismo tipo de plástico que el
Always store discs in their cases vertically, avoiding locations que se utiliza para los discos de audio analógicos
with high heat, humidity, or extremely low temperatures. Avoid convencionales. Tenga cuidado de no permitir que se comben
leaving discs in cars; the interior of a car in direct sunlight can los discos. Ponga siempre los discos en sus cajas
become extremely hot. verticalmente, evitando lugares con mucho calor o humedad,
¶ Always read and abide by the precautionary notes listed on o temperaturas extremadamente bajas. No deje los discos
disc labels. dentro de automóviles, porque el asiento de un automóvil
bajo la luz directa del sol puede ponerse muy caliente.
¶ Lea y respete siempre las notas de precaución que se listan
■ Cleaning discs en las etiquetas de los discos.
¶ Always keep your discs clean by wiping them gently with a
soft cloth from the inner edge toward the outer edge. ■ Limpieza de los discos
¶ When cleaning discs, the use of a commercial CD cleaning kit ¶ Mantenga siempre limpios los discos frotándolos ligeramente
is recommended. con un paño suave desde el borde interior hacia el exterior.
¶ Para limpiar los discos, se recomienda utilizar un juego de
limpieza de discos CD adquirido en un establecimiento del
ramo.
12
En/Sp <DRB1398>
Before Operating (Names
Connections/Conexiones
and Functions
Connections
of Parts)
Connections Conexiones
Always turn off power switch and disconnect power cord Antes de realizar o cambiar conexiones, desconecte siempre
when making or changing connections. el interruptor de la alimentación y desenchufe el cable de
English
alimentación.
Español
be used to control this unit for fader start play and back cue operations. emplear la consola de mezcla para DJ para controlar esta unidad y poder
Note that digital connections can be made only with mixers equipped realizar las operaciones de reproducción de inicio con fundido y de
with digital input connectors (models DJM-800, DJM-1000, etc.). Use a localización regresiva.
commercially available coaxial digital cable to connect this unit’s DIG- Recuerde que las conexiones digitales sólo pueden realizarse con
ITAL OUT connector to the DJ mixer’s DIGITAL IN connector. consolas de mezcla equipadas con conectores de entrada digital (modelos
DJM-800, DJM-1000, etc.). Emplee un cable digital coaxial, de venta en
los establecimientos del ramo, para conectar el conector DIGITAL OUT
de esta unidad al conector DIGITAL IN de la consola de mezcla para DJ.
CONTROL CONTROL
R R
DIGITAL DIGITAL
CD CD
Commercially available
coaxial digital signal cable/
Cable de señal digital coaxial
de venta en los
establecimientos del ramo
CDJ-1000MK3 CDJ-1000MK3
B A
¶ When making connections to the DJM-1000, the furnished audio ca- ¶ Cuando efectúe conexiones con la DJM-1000, podrá utilizar los cables
bles can be used to connect one set of the CD/LINE connectors to de audio suministrados para conectar un juego de conectores CD/
player A, and the other set of CD/LINE connectors to a second player LINE al reproductor A, y el otro juego de conectores CD/LINE a un
B. When making digital audio connections, a commercially available segundo reproductor B. Cuando efectúe conexiones de audio digital,
coaxial digital signal cable must be used to connect the CD player’s deberá emplear un cable de señal digital coaxial, de venta en los
DIGITAL OUT connector to one of the DIGITAL IN connectors (4 to 6) establecimientos del ramo, para conectar el conector DIGITAL OUT
of the DJM-1000 mixer. del reproductor de discos CD a uno de los conectores DIGITAL IN
¶ When connecting to the DJM-600, DJM-300, or DJM-500, use the (4 a 6) de la consola de mezcla DJM-1000.
furnished audio cables to connect the CD1 connectors to player A, ¶ Cuando conecte la DJM-600, DJM-300, o DJM-500, utilice los cables
and CD2 connectors to player B. de audio suministrados para conectar los conectores CD1 al
¶ When connecting to DJM-909 or DJM-707, use the furnished audio reproductor A, y los conectores CD2 al reproductor B.
cables to connect the CH1 CD connectors to player A, and CH2 CD ¶ Cuando conecte la DJM-909 o DJM-707, utilice los cables de audio
connectors to player B. suministrados para conectar los conectores CH1 CD al reproductor
¶ When connecting to DJM-3000, connect player A to CH-1 LINE 1, A, y los conectores CH2 CD al reproductor B.
and player B to CH-2 LINE 3.
13
<DRB1398> En/Sp
Connections/Conexiones
¶ When connecting this CD player to other audio mixers, connect the ¶ Cuando conecte la DJM-3000, conecte el reproductor A a CH-1 LINE
player’s AUDIO OUT connectors to the mixer’s LINE IN or AUX IN 1, y el reproductor B a CH-2 LINE 3.
connectors. (★ DO NOT connect to the PHONO connectors, since ¶ Cuando conecte este reproductor de discos CD a otras consolas de
it may result in distorted sound or improper playback.) mezcla de audio, conecte los conectores AUDIO OUT del reproductor
a los conectores LINE IN o AUX IN de la consola de mezcla. (★ NO
conecte los conectores PHONO, porque podría distorsionarse el
sonido o ocasionar una reproducción inapropiada.)
CDJ-1000MK3 CDJ-1000MK3
Stereo amplifier/
Connect to CD or AUX IN connectors. (Do not connect to PHONO IN connectors.)/
Amplificador estéreo
Conecte a los conectores CD o AUX IN. (No conecte a los conectores PHONO IN.)
CDJ-1000MK3
¶ The DIGITAL OUT connectors produce audio data only (without ¶ Los conectores DIGITAL OUT sólo producen datos de audio (sin
subcodes; CD graphics are not supported). subcódigos; no hay compatibilidad con gráficos de CD).
Depending on the CD recorder or other component connected, some Dependiendo de la grabadora de discos CD u otro componente
recording or other functions may be limited. For details, consult the conectado, pueden limitarse algunas funciones de grabación u otras.
operating instructions for the connected component. Con respecto a los detalles, consulte el manual de instrucciones del
componente conectado.
14
En/Sp <DRB1398>
Names and Functions of Parts/Nomenclatura y funciones de las partes
English
Rear panel/Panel posterior
12
13
35 14
Español
15
34
37 38 36
16 39 40
33
17
32
18
31 19
29
28 21
27 22
26 25 24 23 41 42 43 44
1. Display selector button (TEXT MODE) 1. Botón selector de la visualización modo de texto
Each time this button is pressed, the display alternates between (TEXT MODE)
WAVE and TEXT (track name/album name/artist name). ☞ P. 29 Cada vez que se presiona este botón, la visualización cambia entre WAVE
When playing MP3, WAVE display may not be possible, depending y TEXT (nombre de pista/nombre del álbum/nombre de artista). ☞ P. 29
on the track. Cuando reproduzca archivos MP3, dependiendo de la pista, es posible
que no se muestre la visualización de WAVE.
2. TIME MODE/AUTO CUE button
2. Botón de modo de tiempo/localización automática
TIME MODE:
Each time the button is pressed, the display’s time display alternates
(TIME MODE/AUTO CUE)
TIME MODE:
between the current elapsed play time and the remaining play time
Cada vez que presione el botón, la visualización de tiempo mostrado
(REMAIN). cambiará alternativamente entre el tiempo transcurrido de
When playing MP3, the REMAIN time may not display immediately, reproducción y el tiempo restante de reproducción (REMAIN).
depending on the track. Cuando reproduzca archivos MP3, dependiendo de la pista, es posible
¶ The current TIME MODE setting is retained in memory even when que no se muestre inmediatamente el tiempo de REMAIN.
the power is turned off. ¶ El ajuste actual de TIME MODE permanecerá memorizado incluso
AUTO CUE: aunque desconecte la alimentación.
When the button is held depressed for 1 second or more, the AUTO AUTO CUE:
CUE mode is alternately enabled and disabled. Cuando se mantiene presionado el botón durante 1 o más segundos,
se habilita e inhabilita alternadamente el modo AUTO CUE.
When the button is held depressed for 5 seconds or more, the AUTO
Cuando se mantiene presionado el botón durante 5 o más segundos,
CUE level is toggled. ☞ P. 22 se cambia el nivel de AUTO CUE. ☞ P. 22
¶ The current AUTO CUE on/off and AUTO CUE level settings are ¶ Los ajustes actuales de activación/desactivación de AUTO CUE y
retained in memory even when power is turned off. del nivel de AUTO CUE permanecerán memorizados incluso
3. LOOP IN/REALTIME CUE (IN ADJUST) button/indicator aunque desconecte la alimentación.
Realtime cue ☞ P. 26 3. Botón/indicador de entrada de bucle/localización en tiempo
Loop-in point input ☞ P. 31 real (ajuste de entrada) (LOOP IN/REALTIME CUE (IN ADJUST))
Loop-in point adjust ☞ P. 31 Localización en tiempo real ☞ P. 25
4. LOOP OUT (OUT ADJUST) button/indicator Introducción del punto de entrada de bucle ☞ P. 31
Loop-out point input ☞ P. 31 Ajuste del punto de entrada de bucle ☞ P. 31
Loop-out point adjust ☞ P. 31 4. Botón/indicador de salida de bucle (ajuste de salida)
5. RELOOP/EXIT button ☞ P. 32 (LOOP OUT (OUT ADJUST))
Introducción del punto de salida de bucle ☞ P. 31
6. Display ☞ P. 18 (51 to 66) Ajuste del punto de salida de bucle ☞ P. 31
5. Botón de repetición de bucle/salida (RELOOP/EXIT)
☞ P. 32 15
<DRB1398> En/Sp
Names and Functions of Parts/Nomenclatura y funciones de las partes
English
Flashes in the pause mode to slow that a new cue point can be
25. Mando de lanzadera (+FWD/–REV) ☞ P. 26
input.
26. Indicador de reproducción/pausa
29. CUE button Permanecerá encendido durante la reproducción, y parpadeará du-
Cue point setting ☞ P. 25 rante el modo de pausa.
Back cue ☞ P. 26 27. Botón de reproducción/pausa (PLAY/PAUSE) (6) ☞ P. 22
Cue point sampler ☞ P. 26 28. Indicador de localización ☞ P. 22
30. SEARCH buttons (1, ¡) ☞ P. 23 Se encenderá cuando se haya establecido un punto de localización,
31. TRACK SEARCH buttons (4, ¢) ☞ P. 24 excepto durante la búsqueda.
32. Reverse indicator (REV) Parpadea en el modo de pausa para mostrar que puede introducirse
Español
Lights when DIRECTION selector switch is set to reverse [REV]. un nuevo punto de localización.
33. DIRECTION selector switch (FWD/REV) 29. Botón de localización (CUE)
Ajuste de puntos de localización ☞ P. 24
When set to [REV] (near side), reverse play is enabled. ☞ P. 32 Localización regresiva ☞ P. 26
34. HOT CUE REC MODE button ☞ P. 32 Muestreador de puntos de localización ☞ P. 25
Switches the function of the HOT CUE button (record/call) 30. Botones de búsqueda (SEARCH) (1, ¡) ☞ P. 23
¶ Defaults to call mode when power is first turned on. 31. Botones de búsqueda de pistas (TRACK SEARCH)
35. HOT CUE button/indicator (A, B, C) ☞ P. 32 (4, ¢) ☞ P. 24
When the indicators A, B, C light red, the hot cue point recording 32. Indicador de inversión (REV)
mode is enabled for that point. When any of the indicators A, B, C Se encenderá cuando ponga el selector de sentido DIRECTION en
light green (HOT CUE point) or orange (HOT LOOP point), the re- inversión [REV].
spective call-up mode is enabled, and if the corresponding button is 33. Selector de sentido de avance/inversión
pressed, playback starts from the set hot cue (loop) point. When an (DIRECTION FWD/REV)
indicator is not lighted, no hot cue (loop) point has been recorded. Cuando se ajusta en [REV] (lado cercano), se habilita la reproducción
en el sentido de inversión. ☞ P. 33
Rear Panel 34. Botón de modo de grabación con localización rápida
36. CONTROL connector (HOT CUE REC MODE) ☞ P. 32
Cambia la función del botón HOT CUE (grabación/llamada).
When the accessory control cord is used to connect this connector ¶ Se ajusta al modo predeterminado de llamada cuando se conecta
to the corresponding CONTROL connector on a Pioneer DJ mixer, la alimentación.
the DJ mixer can be used to control the CD player for fader start play 35. Botón/indicador de localización rápida (HOT CUE)
and back cue. (A, B, C) ☞ P. 32
Also, by connecting this connector to the CONTROL connector on Cuando los indicadores A, B, C se encienden en rojo, se habilita el
another Pioneer DJ CD player, automatic relay play can be performed. modo de grabación con punto de localización rápida para este punto.
☞ P. 33 Cuando alguno de los indicadores A, B, C se enciende en verde (punto
37. AUDIO OUT L, R connectors HOT CUE) o en naranja (punto HOT LOOP), se habilita el modo de
RCA-type analog audio output jacks. llamada respectivo, y si se presiona el botón correspondiente, la
38. DIGITAL OUT connector reproducción se inicia desde el punto ajustado de localización (bucle)
rápida. Cuando un indicador no esté encendido, no se habrá grabado
RCA type coaxial digital output connectors used to connect a DJ ningún punto de localización (bucle) rápida.
mixer or AV amplifier, CD player, etc., equipped with digital input
connectors. The digital outputs here support all DJ and other func- Panel posterior
tions, but only audio data is output (without subcodes; CD graphics 36. Conector de control (CONTROL)
are not supported). Cuando se emplea el cable de control accesorio para conectar este
39. POWER — OFF/_ ON switch conector con el conector de CONTROL correspondiente de una
40. AC inlet (AC IN) consola de mezcla para DJ Pioneer, podrá utilizarse la consola de
Use the accessory power cord to connect this inlet to a standard AC mezcla para DJ para controlar el reproductor de discos CD para la
power outlet. reproducción de inicio con fundido y localización regresiva.
Adicionalmente, conectando este conector al conector de CONTROL
de otro reproductor de discos CD para DJ Pioneer, podrá realizarse
Front Panel la reproducción por relevos automáticamente. ☞ P. 33
41. Memory card indicator ☞ P. 34 37. Conectores de salida de audio izquierdo y derecho
This indicator lights with a memory card is loaded and the door is (AUDIO OUT L, R)
closed, and flashes during memory card access. Tomas de salida de audio analógico de tipo RCA.
¶ Do not open the door or turn off power while the indicator is flash- 38. Conector de salida digital (DIGITAL OUT)
ing. Los conectores de salida digitales coaxiales del tipo RCA se emplean
42. Memory card door and slot ☞ P. 34 para conectar una consola de mezcla para DJ o un amplificador au-
diovisual, reproductor de discos CD, etc. , provistos de conectores
43. Forced eject hole ☞ P. 21 de entrada digitales. Las salidas digitales son compatibles con todas
44. Disc loading slot ☞ P. 20 las funciones de DJ y otras, pero sólo se emiten datos de audio (sin
subcódigos; no hay compatibilidad con gráficos de CD).
39. Interruptor de desconexión/conexión de la alimentación
(POWER — OFF/_ ON)
40. Entrada de CA (AC IN)
Emplee el cable de alimentación accesorio para conectar esta toma
de entrada a una toma de corriente de CA normal.
Panel frontal
41. Indicador de tarjeta de memoria ☞ P. 34
Este indicador se enciende cuando se carga una tarjeta de memoria y se
cierra la puerta, y parpadea durante el acceso a la tarjeta de memoria.
¶ No abra la puerta ni desconecte la alimentación mientras el
indicador esté parpadeando.
42. Puerta y ranura de tarjeta de memoria ☞ P. 34
43. Orificio de expulsión forzada ☞ P. 21 17
44. Ranura de carga del disco ☞ P. 20 <DRB1398> En/Sp
Names and Functions of Parts/Nomenclatura y funciones de las partes
51 52 53 54 55 56 57 58 59 60 61 62
63 64 65 66
18
En/Sp <DRB1398>
Names and Functions of Parts/Nomenclatura y funciones de las partes
65. BPM display (0 to 360 BPM) ¶ Durante la visualización del tiempo transcurrido, los segmentos
This display shows the Beats-Per-Minute (BPM) of the currently play- del indicador del gráfico de barras se encienden de izquierda a
ing track (detection range 70 to 180 BPM). The automatic BPM coun- derecha.
ter may be unable to compute the correct BPM for some tracks. ¶ Durante la visualización del tiempo remanente, los segmentos del
66. Tempo control range display (±6, ±10, ±16, WIDE) indicador del gráfico de barras se apagan de izquierda a derecha.
English
Displays the variable range of the tempo adjust slider as selected ¶ Cuando una pista tiene menos de 30 segundos de tiempo
with the tempo control range selector button. remanente de reproducción, el gráfico parpadea lentamente;
cuando el tiempo remanente es de menos de 15 segundos, el
parpadeo pasa a ser más rápido.
65. Visualización de BPM (0 a 360 BPM)
Esta visualización muestra los tiempos por minuto (BPM) de la pista
actualmente en reproducción (margen de detección de 70 a 180
BPM). Es posible que el contador automático de BPM no pueda
calcular el valor de BPM correcto de algunas pistas.
Español
66. Visualización del margen de control del tempo (±6, ±10,
±16, WIDE)
Visualiza el margen variable del mando deslizante de ajuste del tempo
como se haya seleccionado con el botón selector del margen de
control del tempo.
71
72
73
74
75
19
<DRB1398> En/Sp
Loading and Removing Discs/Carga y extracción de discos
1. Set the rear panel POWER switch to ON. 1. Ponga el interruptor POWER del panel posterior en ON.
Do not attempt to force a disc into the slot when the POWER No intente insertar a la fuerza un disco en la ranura cuando el
switch is turned OFF, since the disc or loading mechanism may interruptor POWER esté en OFF, ya que el disco o el mecanismo
be damaged. de carga podrían dañarse.
2. Insert the disc into the loading slot. 2. Inserte el disco en la ranura de carga del mismo.
¶ Hold the disc with label surface upwards and insert evenly into ¶ Sujete el disco con la superficie de la etiqueta hacia arriba, e
the front-panel disc loading slot. insértelo nivelado en la ranura de carga del disco del panel frontal.
¶ When using 8 cm discs, place the disc into an adapter first. ¶ Para utilizar un disco compacto de 8 cm, colóquelo primero en un
adaptador.
This unit spins at high speed to provide high performance.
When playing 8 cm discs with an adaptor, for safety rea- Esta unidad gira a alta velocidad para conseguir su alto
sons the rotation speed is reduced as a result scratch and rendimiento. Cuando se reproducen discos de 8 cm con un
reverse speeds will be lower. adaptador, se restringe la velocidad de rotación por razones
de seguridad, por lo que las velocidades de rascado y de
¶ Only one disc can be loaded at a time. Do not attempt to load two inversión serán inferiores.
or more discs simultaneously, or to load a second disc when an-
other disc is already loaded. ¶ Solamente podrá cargarse un disco a la vez. No intente cargar
¶ When loading a disc, do not apply bending force on the disc, or simultáneamente dos o más discos, ni cargar un segundo disco
attempt to force the disc into the mechanism. Also, when the load- cuando ya haya otro cargado.
ing mechanism begins to pull the disc into the player or to eject a ¶ Cuando cargue un disco, no lo doble, ni intente insertarlo a la fuerza
disc, do not attempt to forcibly override the mechanism’s move- en el mecanismo. Además, cuando el mecanismo de carga comience
ment, since the disc or loading mechanism may be damaged. a tirar del disco para cargarlo o a expulsarlo, no intente impedir a la
3. When the EJECT UNLOCK/LOCK switch is set to [UNLOCK], fuerza el movimiento del mecanismo, ya que el disco o el mecanismo
press the EJECT (0) button to eject a loaded disc. de carga podrían dañarse.
If the EJECT UNLOCK/LOCK switch is set to [LOCK] , dur- 3. Para extraer un disco cargado, con el interruptor EJECT
ing playback press the PLAY/PAUSE (6) button to first UNLOCK/LOCK ajustado a [UNLOCK], presione EJECT (0).
stop the disc, then press the EJECT (0) button. If a cue Si el interruptor EJECT UNLOCK/LOCK está ajustado a
point has been set, during playback press the CUE button [LOCK], durante la reproducción presione en primer lugar
to initiate back cue, then press the EJECT (0) button to el botón PLAY/PAUSE (6) para parar el disco, y después
eject the disc. presione el botón EJECT (0). Si había ajustado un punto
¶ When the button is pressed, disc rotation will stop and the disc de localización, durante la reproducción presione el botón
will be ejected partway from the loading slot. CUE para iniciar la localización regresiva, y después
presione el botón EJECT (0) para extraer el disco.
Note: ¶ Cuando presione este botón, el disco dejará de girar y saldrá
Do not attempt to press the disc back into the slot while the [EJECT] expulsado en parte por la ranura de carga.
indicator is lighted. If the disc is pressed back in while the [EJECT]
indicator is lighted, the loading mechanism may stop. In this case, Nota:
press the EJECT (0) button again, and do not attempt to reload the No intente presionar el disco para insertarlo en la ranura mientas el
disc until the [EJECT] indicator has turned OFF. indicador [EJECT] esté encendido. Si presionase el disco para
insertarlo con el indicador [EJECT] encendido, el mecanismo de carga
podría pararse. En este caso, vuelva a presionar el botón EJECT
(0), y no intente volver a cargar el disco hasta que se apague el
indicador [EJECT].
20
En/Sp <DRB1398>
Loading and
Before
Removing
Operating
Discs/Carga
(Names and
y extracción
Functionsde
of discos
Parts)
English
ately press the EJECT (0) button and remove the disc. If the mediante las lengüetas del adaptador. Si carga un disco de 8 cm
disc is not ejected the first time the EJECT (0) button is pressed, por error sin adaptador, presione inmediatamente el botón EJECT
press the button again. (0) y extraiga el disco. Si el disco no sale expulsado la primera
2 Use only 8 cm disc adapters that feature the ' logo mark (rec- vez que presione el botón EJECT (0), vuelva a presionar el botón.
ommended compatible adapters). When mounting the disc to 2 Utilice solamente adaptadores para discos de 8 cm que tengan la
an adapter, confirm that the disc is able to rotate freely, and is marca de logotipo ' (adaptadores compatibles recomendados).
not bent or warped. Cuando monte un disco en un adaptador, confirme que el disco
pueda girar libremente, y que no esté doblado ni alabeado.
Español
Forced eject function
If a disc fails to be ejected when the EJECT (0) button is Función de expulsión forzada
pressed or otherwise when you cannot remove a disc, in-
Si el disco falla en salir expulsado cuando se presione el
sert the provided pin into the forced eject hole at the front of
botón EJECT (0), o no pueda extraerlo por alguna otra causa,
the player (see illustration) and press to eject the disc.
inserte el pasador suministrado en el orificio de expulsión
When using the forced eject function, be sure to following
forzada de la parte frontal del reproductor (consulte la
the accompanying precautions.
ilustración), y presiónelo para expulsar el disco.
1 Turn off the player’s power and wait for at least one
Cuando utilice la función de expulsión forzada, tenga en
minute.
cuenta las precauciones siguientes.
1 Desconecte la alimentación del reproductor y espere un
Attempting the forced eject function im-
minuto por lo menos.
mediately after turning off the power may
cause the following dangers:
Si intentase utilizar la función de expulsión
¶ The disc may be ejected while still rotating, resulting
forzada inmediatamente después de haber
in personal injury.
desconectado la alimentación, podrían
¶ The disc may be damaged due to the disc clamp’s
producirse los peligros siguientes:
rotating in an unstable condition.
¶ El disco puede salir expulsado mientras esté girando
todavía, lo que podría resultar en lesiones personales.
2 Use only the provided accessory pin for this procedure
¶ El disco podría dañarse debido a que al giro en
(do not use other pointed objects). The forced eject pin
condición inestable del sujetador del disco.
is located on the bottom surface of the player.
When the accessory pin is inserted fully into the forced
2 Para este procedimiento utilice solamente el pasador
eject hole, the disc will be ejected from the loading slot
accesorio suministrado (no utilice ningún otro objeto
by about 5 mm to 10 mm. It can then be grasped with the
puntiagudo). El pasador de expulsión forzada se
fingers and removed.
encuentra en la superficie inferior del reproductor.
Cuando inserte completamente el pasador accesorio en
el orificio de expulsión forzada, el disco saldrá expulsado
por la ranura de carga unos 5 mm a 10 mm. Podrá tomarse
con los dedos y extraerse.
Orificio de expulsión
forzada
21
<DRB1398> En/Sp
DJ Player Operation/Operación del reproductor para DJ
English
press the PLAY/PAUSE button (6) during playback, or que estaba antes de presionarse el botón EJECT. No obstante, la
when a Cue point has been set, press the CUE button salida de audio se detendrá durante este proceso.
(back cue) before pressing the EJECT button (0) to eject ¶ Después de la expulsión del disco, si se vuelve a insertar el mismo
the disc. disco, la unidad volverá al mismo estado en el que estaba antes de
¶ Playback will stop and the disc will be ejected. expulsar el disco (con la excepción de bucles).
¶ Note that the CDJ-1000MK3 does not come with a stop button. ¶ Después de la expulsión del disco, si se presiona el botón FOLDER
Resume function SEARCH (|, \) o TRACK SEARCH (4, ¢), se cancelará la función
¶ When the EJECT UNLOCK/LOCK switch is in the [UNLOCK] posi- de reanudación.
tion, even if the EJECT button is pressed by mistake, if the PLAY/
Español
PAUSE button is pressed quickly (before the [EJECT] indicator lights Para pausar la reproducción
in the display), the unit will revert to the status it was in before the Durante la reproducción, presione el botón PLAY/PAUSE
EJECT button was pressed. However, the audio output will stop dur-
(6).
ing that time.
¶ Los aros exteriores del botón PLAY/PAUSE y del botón CUE
¶ Following disc eject, if the same disc is reinserted, the unit will return
parpadearán, y la reproducción se interrumpirá.
to the same status it was in before the disc was ejected (with excep-
¶ Si se presiona el botón PLAY/PAUSE, el aro exterior del botón se
tion of loop).
encenderá y se reanudará la reproducción.
¶ Following disc eject, if the FOLDER SEARCH button (|, \) or TRACK
¶ En el modo CDJ, saldrá sonido distorsionado de reproducción incluso
SEARCH button (4, ¢) is pressed, the resume function will be
durante la pausa. Si no desea que salga sonido, reduzca el nivel de
canceled.
salida de la consola de mezcla de audio.
¶ En el modo VINYL, el ajuste del mando VINYL SPEED ADJUST
To pause playback TOUCH/BRAKE modifica la velocidad de desaceleración hasta que
During playback, press the PLAY/PAUSE button (6). la reproducción llega a la pausa completa. Al girar el mando hacia la
¶ The outer rings of the PLAY/PAUSE button and CUE button will flash, derecha, el disco se desacelera lentamente antes de establecerse la
and playback will be interrupted. pausa.
¶ If the PLAY/PAUSE button is pressed again, the button’s outer ring ¶ En el modo VINYL, el ajuste del mando VINYL SPEED ADJUST RE-
will light and playback will resume. LEASE/START modifica la velocidad de aceleración del disco cuando
¶ In CDJ mode, broken playback sound will be output even during pause. se libera la pausa hasta que llega a la velocidad tope de reproducción.
If you wish for no sound to be output, lower the output level of the Al girar el mando hacia la derecha, el disco se acelera con más lentitud
audio mixer. antes de llegar a la velocidad tope.
¶ In VINYL mode, setting the VINYL SPEED ADJUST TOUCH/BRAKE ¶ Después de establecer la unidad en el modo de pausa, si no se efectúa
dial modifies the speed of deceleration until playback reaches full ninguna otra operación durante 100 minutos, la rotación del disco se
pause. Rotating the dial clockwise causes the disc to decelerate slowly detendrá automáticamente. En este caso, presione el botón PLAY/
before the pause. PAUSE para reanudar la reproducción.
¶ In VINYL mode, setting the VINYL SPEED ADJUST RELEASE/
START dial modifies the speed at which the disc accelerates when Avance rápido/inversión rápida
pause is released until reaching full playback speed. Rotating the dial
Presione uno de los botones SEARCH (1, ¡) durante la
clockwise causes the disc to accelerate more slowly to full speed.
¶ After setting the unit to pause, if no subsequent operation is per-
reproducción.
formed for 100 minutes, the disc rotation will automatically stop. In Presione y mantenga presionado el botón ¡ para realizar el avance
this event, pressing the PLAY/PAUSE button will cause playback to rápido en el disco; presione y mantenga presionado el botón 1 para
realizar la inversión rápida.
resume.
¶ Durante la reproducción de archivos MP3, el avance rápido/inversión
rápida sólo pueden realizarse para las pistas de dentro de la misma
Fast forward/Fast reverse carpeta.
Press one of the SEARCH buttons (1, ¡) during playback. ¶ Durante la reproducción de archivos MP3, los tiempos del avance
Press and hold the ¡ button for fast forward the disc; press and hold rápido/inversión rápida pueden ser más lentos dependiendo de la pista.
the 1 button for fast reverse. 7 Búsqueda súper rápida
¶ When playing MP3, fast forward/fast reverse are supported only for Gire el mando de lanzadera mientras presiona uno de los
tracks inside the same folder. botones SEARCH (1, ¡).
¶ When playing MP3, fast forward/fast reverse times may be slower
¶ Mantenga presionado uno de los botones SEARCH (1, ¡) mientras
depending on the track.
gira el mando de lanzadera en la dirección deseada para establecer el
7 Super-fast search modo de avance súper rápido o de inversión súper rápida.
Rotate the jog dial while pressing one of the SEARCH but- ¶ La velocidad de la operación de búsqueda varía en respuesta a la
tons (1, ¡). velocidad a la que se gira el mando de lanzadera.
¶ Hold down one of the SEARCH buttons (1, ¡) while turning the ¶ Durante la búsqueda súper rápida, la dirección de búsqueda se
jog dial in the desired direction to enter super-fast forward or super- determina por la dirección en la que se gira el mando de lanzadera. Se
fast reverse mode. ignora la dirección del botón SEARCH (1, ¡) presionado.
¶ The speed of the search operation varies in response to the speed at ¶ Cuando se deja de girar el mando de lanzadera, el aparato retorna al
which the jog dial is turned. modo de reproducción.
¶ During super-fast search, the search direction is determined by the ¶ Cuando se suelta el botón SEARCH (1, ¡), se cancela la búsqueda
direction the jog dial is turned. The direction of the pressed SEARCH súper rápida.
button (1, ¡) is ignored. ¶ Durante la reproducción de archivos MP3, el avance rápido/inversión
¶ When the jog dial rotation stops, the unit returns to playback mode. rápida sólo pueden realizarse para las pistas de dentro de la misma
¶ When the SEARCH button (1, ¡) is released, super-fast search is carpeta.
canceled. ¶ Durante la reproducción de archivos MP3, los tiempos del avance
¶ When playing MP3, fast forward/fast reverse is supported only tracks rápido/inversión rápida pueden ser más lentos dependiendo de la pista.
inside the same folder.
¶ When playing MP3, fast forward/fast reverse times may be slower
depending on the track.
23
<DRB1398> En/Sp
DJ Player Operation/Operación del reproductor para DJ
24
En/Sp <DRB1398>
DJ Player
Before
Operation/Operación
Operating (Names del
andreproductor
Functions of
para
Parts)
DJ
¶ Folders with no playable tracks (empty folders) will be ignored, and 7 Ajuste del punto de localización en el modo CDJ
the next folder will be searched. 1. Durante la reproducción, presione el botón PLAY/PAUSE
7 Super-fast folder search (6) para pausar la reproducción en el punto que usted
Rotate the jog dial while pressing one of the FOLDER desee iniciar la reproducción.
SEARCH buttons (|, \). 2. Busque la posición precisa del punto de localización.
English
¶ By turning the jog dial in the intended search direction while pressing ¶ Empleo de los números de trama para especificar los puntos
either of the FOLDER SEARCH buttons, folder numbers will be de localización.
searched corresponding to the direction of rotation of the jog dial. Los puntos de localización pueden especificarse en unidades de 1
¶ During super-fast folder search, the search direction is determined by trama (75 tramas equivalen a 1 segundo).
the direction the jog dial is rotated. The direction indicated by the Emplee el mando de lanzadera o los botones SEARCH (1, ¡)
pressed FOLDER SEARCH button is ignored. para hacer avanzar las tramas. Una rotación del mando de lanzadera
¶ When the FOLDER SEARCH button is released, super-fast folder equivale a 135 tramas; cuando se presione el botón SEARCH, el
search is canceled. reproductor avanzará 1 trama en la dirección especificada.
¶ Escuche el sonido en la trama actual para determinar el punto
Español
Cue point settings de localización.
Once a cue point has been stored in memory, during playback it can be Gire lentamente el mando de lanzadera y luego retórnelo a justo
used to place the player in a state where it is ready to begin playback antes del punto desde el que desee iniciar la reproducción. (El
from the cueing position by pressing the CUE button. punto de localización de este modo definido constará de este punto
directamente después del sonido que puede oírse durante una
7 Setting the cue point in the CDJ mode
pausa de localización.)
1. During playback, press the PLAY/PAUSE button (6) to
3. Presione el botón CUE cuando llegue al número de la
pause playback at the point you wish to begin playback.
trama deseada o cuando oiga el sonido en el punto desde
2. Search for the precise position of the cue point.
el que desea iniciar la localización.
¶ Using frame numbers to specify cue points.
¶ El sonido se silencia y aparece la visualización del tiempo actual,
Cue points may be specified in 1-frame units (where 75 frames
indicando que queda el punto de localización ha sido almacenado
are equivalent to 1 second).
en la memoria.
Use the jog dial or the SEARCH button (1, ¡) to advance
¶ Cuando almacene un nuevo punto de localización en la memoria,
frames. One rotation of the jog dial is equivalent to 135 frames;
el ajuste previamente almacenado se borrará.
when the SEARCH button is pressed, the player advances 1 frame
in the specified direction.
[Enmienda del punto de localización]
¶ Listen to the sound at the current frame to determine the cue 1. Durante la reproducción, presione el botón CUE.
point. ¶ El reproductor volverá al punto de localización especificado.
Turn the jog dial slowly and then return it to just before the point 2. Presione uno de los botones SEARCH (1, ¡) para
from which you wish to begin playback. (The cue point thus de- establecer el modo de pausa audible.
fined will consist of that point directly after the sound which can 3. En el modo CDJ, para ajustar el punto de localización
be heard during a cueing pause.) realice los pasos 2 y 3 como se ha indicado anteriormente.
3. Press the CUE button when you reach the desired frame
7 Ajuste del punto de localización en el modo VINYL
number or hear the sound at the point from which you
1. Durante la reproducción, cuando la reproducción llegue
wish to begin cueing.
¶ The sound will mute and the current time will appear in the dis- al punto de localización deseado, presione y mantenga
play, indicating that the cue point has been stored to memory. presionada la superficie del mando de lanzadera, o
¶ When a new cue point is stored in memory the previous setting presione el botón PLAY/PAUSE (6) para pausar la
will be erased. reproducción.
[Amending the cue point] 2. Mientras sigue presionando la superficie del mando de
1. During playback, press the CUE button. lanzadera, gírelo para que la reproducción vuelva al punto
¶ The player will return to the specified cue point. de audio de antes del punto desde el que usted desea
2. Press one of the SEARCH buttons (1, ¡) to set to au- que se inicie la reproducción.
dible pause mode. 3. Cuando el audio esté en el punto de localización deseado,
3. In the CDJ mode, to set the cue point, go through steps 2 presione el botón CUE mientras sigue presionando la
and 3 as mentioned above. superficie del mando de lanzadera.
7 Setting the cue point in the VINYL mode ¶ El ajuste de la memoria del punto de localización se completa
1. During playback, when playback reaches the desired cue cuando se enciende el tiempo actual en el visualizador.
point, either press and hold the surface of the jog dial, or ¶ Cuando almacene un nuevo punto de localización en la memoria,
el ajuste previamente almacenado se borrará.
press the PLAY/PAUSE button (6) to pause playback.
[Enmienda del punto de localización]
2. While continuing to press the surface of the jog dial, ro-
1. Durante la reproducción, presione el botón CUE.
tate it to return playback to the audio point just before
¶ El reproductor volverá al punto de localización especificado.
the point you wish playback to begin.
2. En el modo VINYL, para ajustar el punto de localización
3. When the audio is at the desired cue point, press the CUE
realice los pasos 2 y 3 como se ha indicado anteriormente.
button while continuing to press on the surface of the
¶ Ahora podrá utilizar los botones SEARCH (1, ¡) para modificar
jog dial. el punto de localización, del mismo modo que para el modo CDJ.
¶ Cue point memory setting is completed when the current time
lights in the display. 7 Localización en tiempo real
¶ When a new cue point is stored in memory the previous setting Durante la reproducción, presione el botón LOOP IN/
will be erased. REALTIME CUE en el punto de localización deseado.
[Amending the cue point] ¶ Este punto se grabará entonces como nuevo punto de localización.
1. During playback, press the CUE button.
¶ The player will return to the specified cue point.
7 Comprobación de los puntos de localización
2. In the VINYL mode, to set the cue point, go through steps (muestreador de puntos de localización)
2 and 3 as mentioned above. Después del ajuste de un punto de localización, mantenga
¶ The SEARCH buttons (1, ¡) can now be used to modify the presionado el botón CUE.
cue point, in the same way as for the CDJ mode.
25
<DRB1398> En/Sp
DJ Player Operation/Operación del reproductor para DJ
7 Realtime cue ¶ Mientras mantenga presionado el botón CUE, podrá oírse el sonido
During playback, press the LOOP IN/REALTIME CUE button del punto de localización ajustado.
at the desired cue point. ¶ Durante la función del muestreador de puntos de localización, si se
¶ This point will then be recorded as the new cue point. suelta el botón CUE, se efectuará la localización regresiva para el
punto de localización ajustado.
7 Checking cue points (Cue point sampler) ¶ En el caso de archivos MP3, la función del muestreador de puntos de
After setting a cue point, hold the CUE button depressed. localización sólo podrá realizarse dentro de la misma carpeta.
¶ As long as the CUE button is held depressed, the sound at the set
cued point can be heard. 7 Para volver a un punto de localización
¶ During cue point sampler, if the CUE button is released, back cue will (localización regresiva)
be performed to the set cue point. 1. Durante la reproducción, presione el botón CUE.
¶ In the case of MP3, cue point sampler can be performed only within ¶ El reproductor volverá al punto de localización especificado.
the same folder. 2. Presione el botón PLAY/PAUSE (6).
7 Returning to a Cue point (Back cue) ¶ La reproducción se iniciará inmediatamente desde el punto de
1. During playback, press the CUE button. localización especificado.
¶ The player will return to the specified cue point. ¶ En el caso de archivos MP3, la localización regresiva podrá
2. Press the PLAY/PAUSE button (6). efectuarse dentro de la misma carpeta. Mientras no se sobrescriba
¶ Playback will begin immediately from the specified cue point. el punto de localización por otro nuevo, quedará almacenado en la
¶ In the case of MP3, back cue can be performed within the same memoria también después de la búsqueda de la carpeta.
folder. So long as the cue point is not overwritten, it will remain in
memory after folder search as well.
Para cambiar la velocidad de reproducción
MP3 FOLDER SEARCH
|, \ Mueva el control deslizante de ajuste del tempo hacia delante
o hacia atrás.
Cuando se mueve hacia el usuario (+), se acelera la velocidad de
JOG reproducción (el tempo), y cuando se aleja del usuario (–), se aminora la
ADJUST velocidad de reproducción.
TEXT MODE
¶ El grado de cambio del tempo se muestra en el visualizador.
¶ Incluso cuando se cambia el tempo, el tono (la clave) puede conservarse
JOG estable (vea la sección siguiente “Aplicación del tempo principal”).
MODE
SELECT 7 Selección del margen de ajuste del tempo
TRACK TEMPO Presione el botón TEMPO ±6/±10/±16/WIDE.
±6/±10/±16/WIDE Cada vez que presione el botón, el margen variable del control deslizante
SEARCH
4, ¢ MASTER del tempo alternará en el orden de ±6 %/±10 %/±16 %/WIDE. Cuando
TEMPO
SEARCH TEMPO se selecciona ±6 %, la unidad de cambio será 0,02 %; cuando se
1, ¡ RESET selecciona ±10 %, la unidad de cambio será 0,05 %; cuando se selecciona
±16 %, la unidad de cambio será 0,05 %, y cuando se selecciona WIDE,
CUE la unidad de cambio será 0,5 %.
¶ El valor de ajuste variable se muestra en el visualizador.
PLAY/PAUSE
6 ¶ El margen variable en el ajuste WIDE es como sigue:
Jog dial/ Con reproducción de discos CD: ±100 %
Mando de lanzadera Tempo adjust slider/ Con reproducción de archivos MP3: +70 % a –100 %
Control deslizante de tempo ¶ Cuando se conecta la alimentación al principio, el ajuste vuelve al
predeterminado de ±10 %.
To change the playing speed ¶ En –100 %, se detiene la reproducción.
Move the tempo adjust slider forward or back. 7 Reposición del tempo
When moved toward the user (+) the playing speed (tempo) becomes Presione el botón TEMPO RESET.
faster, and when moved away (–) the playing speed becomes slower. El indicador de reposición del tempo se encenderá y el régimen de cambio
¶ The degree of change in tempo is shown on the display. del tempo pasará a ser “0” (tempo normal), independientemente de la
¶ Even when changing the tempo, the pitch (key) can be kept stable posición del mando deslizante de ajuste del tempo.
(see section below, “Applying master tempo”). ¶ Si vuelve a presionar el botón TEMPO RESET, la reposición se
cancelará (el régimen de cambio del tempo volverá al valor ajustado
7 Selecting the range of tempo adjustment con el mando deslizante de ajuste del tempo).
Press the TEMPO ±6/±10/±16/WIDE button. ¶ Cuando se conecta la alimentación al principio, esta función se
Each time the button is pressed the tempo adjust slider’s variable range establece en el ajuste predeterminado de OFF.
alternates in the order ±6 %/±10 %/±16 %/WIDE. When ±6 % is se-
lected, the unit of change is 0.02 %; when ±10 % is selected, the unit of Aplicación del tempo principal
change is 0.05 %; when ±16 % is selected, the unit of change is 0.05 %,
and when WIDE is selected, the unit of change is 0.5 %. Presione el botón MASTER TEMPO durante la reproducción.
¶ The variable setting value is shown on the display. Se encienden el botón MASTER TEMPO y el indicador [MT]. La velocidad
¶ The variable range in the WIDE setting is as follows: (el tempo) podrá ahora cambiarse empleando el mando deslizante de
With CD play: ±100 % ajuste del tempo, pero el tono (la clave) no cambiará.
With MP3 play: +70 % to –100 % ¶ La calidad del sonido se degradará cuando se someta a proceso digital.
¶ When power is first turned on, the setting defaults to ±10 %. ¶ Cuando se conecta la alimentación al principio, esta función se
¶ At –100 %, playback stops. establece en el ajuste predeterminado de OFF.
English
2. Reproducción rascada: Gire el mando de lanzadera du-
¶ Sound quality will be degraded when subjected to digital processing.
¶ When power is first turned on, this function defaults to OFF.
rante la reproducción.
Consulte el apartado “Reproducción rascada” de la sección de
Operaciones avanzadas.
Jog dial functions 3. Búsqueda por tramas: Gire el mando de lanzadera du-
1. Pitch bend: Rotate jog dial during playback. rante el estado de pausa.
(When the jog mode is set to [VINYL], touch only the sides of the jog Cuando se ajusta el modo de lanzadera en [CDJ], se habilita el modo
dial. If the top surface is touched a different function is performed.) de pausa audible y cuando se ajusta en [VINYL], se realiza la pausa
¶ In proportion to the amount of rotation, the playback speed is ac- inaudible; el audio del disco CD se reproduce a una velocidad
Español
celerated (FWD+) or decelerated (REV–). When in the reverse correspondiente a la velocidad de rotación del mando de lanzadera.
mode, the playback speed accelerates when the dial is rotated in ¶ La posición de pausa cambia en unidades de 1 trama.
the REV– direction, and decelerates when rotated in the FWD+ ¶ Una rotación del mando de lanzadera corresponde a 1,8 segundos
direction. de reproducción del disco CD (135 tramas).
¶ When dial rotation is stopped, playback reverts to the previous 4. Reproducción con rotación: Gire el mando de lanzadera
speed. durante la reproducción o pausa.
2. Scratch play: Rotate jog dial during playback. Consulte el apartado “Reproducción con rotación” de la sección de
See “Scratch play” in the Advanced Operations. Operaciones avanzadas.
3. Frame search: Rotate jog dial during pause. 5. Búsqueda súper rápida: Gire el mando de lanzadera du-
When jog mode is set to [CDJ], the audible pause mode is enabled rante la reproducción, mientras mantiene presionado el
and when set to [VINYL], inaudible pause is performed; the CD audio
botón SEARCH.
is played at a speed corresponding to the speed of jog dial rotation.
Para realizar la búsqueda a alta velocidad, mantenga presionado el botón
¶ The pause position will change in units of 1 frame.
SEARCH (1, ¡) mientras gira el mando de lanzadera en el sentido
¶ One rotation of the jog dial corresponds to 1.8 seconds of CD
en el que desee realizar la búsqueda; la búsqueda a alta velocidad se
playback (135 frames).
efectuará en proporción al grado de rotación del mando de lanzadera.
4. Spin play: Rotate jog dial during playback or pause.
¶ La velocidad de la operación de búsqueda varía en respuesta a la
See “Spin play” in the Advanced Operations.
velocidad a la que se gira el mando de lanzadera.
5. Super-fast search: Rotate jog dial during playback, while ¶ La búsqueda se efectúa en el sentido de rotación del mando de
holding SEARCH button depressed. lanzadera, sin tener importancia el botón SEARCH que se haya
To perform high-speed search, hold the SEARCH button (1, ¡) presionado.
depressed while rotating the jog dial in the desired direction of search; ¶ Cuando se deja de girar el mando, la reproducción retorna a la
high-speed search will be performed in proportion to the degree of normalidad.
jog dial rotation. ¶ Cuando se suelta el botón SEARCH, se cancela este modo.
¶ The speed of the search operation varies in response to the speed ¶ Durante la reproducción de archivos MP3, el avance rápido/
at which the jog dial is turned. inversión rápida sólo pueden realizarse dentro de la misma carpeta.
¶ The search is performed in the direction of jog dial rotation, with- 6. Búsqueda súper rápida de pistas: Gire el mando de
out regard to which SEARCH button is pressed. lanzadera mientras mantiene presionado el botón TRACK
¶ When dial rotation is stopped, playback returns to normal.
SEARCH.
¶ When the SEARCH button is released, this mode is canceled.
Para realizar la búsqueda de pistas a alta velocidad, mantenga
¶ When playing MP3, fast forward/fast reverse can be performed
presionado el botón TRACK SEARCH (4, ¢) mientras gira el
only within the same folder.
mando de lanzadera en el sentido en el que desee realizar la búsqueda;
6. Super-fast track search: Rotate jog dial while holding
la búsqueda de pistas a alta velocidad se efectuará en proporción a la
TRACK SEARCH button depressed. cantidad de rotación del mando de lanzadera.
To perform high-speed track search, hold the TRACK SEARCH but- ¶ La búsqueda se efectúa en el sentido de rotación del mando de
ton (4, ¢) depressed while rotating the jog dial in the desired lanzadera, sin tener importancia el botón TRACK SEARCH que se
direction of search; high-speed track search will be performed in pro- haya presionado.
portion to the amount of jog dial rotation. ¶ Cuando se suelta el botón TRACK SEARCH, se cancela este modo.
¶ The search is performed in the direction of jog dial rotation, with- ¶ Cuando se reproducen archivos MP3, la búsqueda sólo puede
out regard to which TRACK SEARCH button is pressed. efectuarse dentro de la misma carpeta.
¶ When the TRACK SEARCH button is released, this mode is 7. Búsqueda súper rápida de carpetas: Gire el mando de
canceled.
lanzadera mientras mantiene presionado el botón FOLDER
¶ When playing MP3, search is performed only within the same
folder. SEARCH (durante la reproducción de archivos MP3).
Para realizar la búsqueda súper rápida de carpetas, mantenga
7. Super-fast folder search: Rotate jog dial while holding
presionado el botón FOLDER SEARCH (|, \) mientras gira el mando
FOLDER SEARCH button depressed (during MP3 play).
de lanzadera en el sentido en el que desee realizar la búsqueda; la
To perform super-fast folder search, hold the FOLDER SEARCH but-
búsqueda súper rápida de carpetas se efectuará en proporción a la
ton (|, \) depressed while rotating the jog dial in the desired direc-
cantidad de rotación del mando de lanzadera.
tion of search; super-fast folder search will be performed in propor-
¶ La búsqueda se efectúa en el sentido de rotación del mando de
tion to the amount of jog dial rotation.
lanzadera, sin tener importancia el botón FOLDER SEARCH que
¶ The search is performed in the direction of jog dial rotation, with-
se haya presionado.
out regard to which FOLDER SEARCH button is pressed.
¶ Cuando se suelta el botón FOLDER SEARCH, se cancela este modo.
¶ When the FOLDER SEARCH button is released, this mode is
canceled.
Nota:
La superficie del mando de lanzadera está provista de un
Note:
interruptor incorporado; no apoye objetos sobre el mando ni le
The surface of the jog dial is equipped with a built-in switch;
aplique mucha fuerza. No ponga bebidas sobre la superficie,
do not rest objects on the dial or subject it to strong forces.
porque si algún líquido se introdujera en el mecanismo, causaría
Do not set drinks on the surface, since a spill could enter the
mal funcionamiento.
mechanism and cause malfunctions.
27
<DRB1398> En/Sp
DJ Player Operation/Operación del reproductor para DJ
English
Using the cross fader start function of a Pioneer DJ mixer, step 10 above Si el valor de BPM coincide, la mezcla de las pistas A y B sonará bien
can be eliminated for even simpler mixing. In addition, when the CROSS aunque el control deslizante CROSS FADER esté en la posición intermedia.
FADER slider is returned to its original position, the status returns to that
in step 9 (player CD2 at its cue point), so that you can repeat the same 7 Reproducción de inicio con fundido
play as many times as you like. Empleando la función de inicio con fundido de una consola de mezcla
para DJ Pioneer, podrá eliminarse el paso 10 anterior para simplificar
todavía más la mezcla. Adicionalmente, cuando se reponga el control
About the WAVE display deslizante CROSS FADER a su posición original, el estado vuelve al del
The WAVE display shows the changes in a track’s bass beat (bass drum, paso 9 (reproductor CD2 en su punto de localización), por lo que puede
Español
etc.), thus allowing the DJ to understand where breaks and end points repetirse la misma reproducción tantas veces como se desee.
come in the track. When the TEXT MODE button is set for WAVE dis-
play, the selected track is shown rescaled to fit within the full range (100
Acerca de la visualización de ondas (WAVE)
points) of the display. La visualización de WAVE muestra los cambios en el compás de los
¶ After a track change, some time is required before the entire track’s sonidos graves de la pista (bombo de batería, etc.), para que el usuario
WAVE display can be shown. By prerecording desired tracks’ WAVE pueda saber dónde se encuentran los puntos de interrupción y finalización
patterns on a memory card, the next time the track is played its WAVE de la pista. Cuando el botón TEXT MODE se ajusta para la visualización
pattern can be displayed instantly (☞ P. 35). de WAVE, se muestra la pista seleccionada graduada para que entre en
¶ If a track’s low-frequency beat changes are too low in volume, the toda la anchura (100 puntos) del visualizador.
¶ Después de un cambio de pista, se requiere cierto tiempo para que
break points in the track may not be displayed properly.
se muestre la visualización WAVE de la pista entera. Grabando de
¶ If a search or pause operation is performed during the time the wave-
antemano los patrones de WAVE de las pistas deseadas en una tarjeta
form is being read, the waveform will not be displayed properly.
de memoria, la vez siguiente que se reproduzca la pista, podrá
¶ Read-ahead of the WAVE pattern is not possible during MP3 play- visualizarse instantáneamente su patrón de WAVE (☞ P. 35).
back. ¶ Si los cambios rítmicos de bajas frecuencias de la pista tienen un
volumen demasiado bajo, es posible que los puntos de interrupción
About TEXT display de la pista no se visualicen correctamente.
When the TEXT MODE button is used to select TEXT display, the dis- ¶ Si se efectúa una operación de búsqueda o de pausa durante el tiempo
play shows CD-TEXT, including the names of tracks, albums, and artists. en el que se lee la forma de onda, la forma de onda no se visualizará
correctamente.
During MP3 playback, the display shows ID3 tag track name (if no ID3
¶ La lectura adelantada del patrón WAVE no puede realizarse durante la
tag is recorded, the display shows the file name) / ID3 tag album name /
reproducción de archivos MP3.
ID3 tag artist name.
¶ Each item can display up to 48 characters of text; text longer than 16 Acerca de la visualización de texto (TEXT)
characters is scrolled.
¶ Text may include alphanumerics and some symbols. Cuando se emplea el botón TEXT MODE para seleccionar la visualización
¶ If no text is available, the [NO TEXT] message will be displayed. de TEXT, el visualizador muestra el texto del CD (CD-TEXT), incluyendo los
nombres de pista, de álbum, y del artista. Durante la reproducción de
archivos MP3, la visualización mostrará el nombre de la pista de la etiqueta
When a track name is selected in TEXT display, the [ ] icon will be
ID3 (si no está grabada la etiqueta ID3, la visualización mostrará el nombre
displayed followed by the track name (with MP3, the ID3 tag’s title name
de archivo)/nombre de álbum de la etiqueta ID3/nombre del artista de la
or file name will be displayed).
etiqueta ID3.
Also, during MP3 play, the bit rate will be displayed following the track ¶ Pueden visualizarse hasta 48 caracteres de texto de cada elemento;
name. el texto con más de 16 caracteres se desplaza.
¶ El texto puede incluir caracteres alfanuméricos y algunos símbolos.
¶ Si no hay texto disponible, se visualizará el mensaje [NO TEXT].
When an album name is selected in TEXT display, the [ ] icon will be Cuando se selecciona un nombre de pista en el visualizador de TEXT, se
displayed followed by the album name. visualizará el icono [ ] seguido del nombre de pista (en caso de MP3,
se visualizará el nombre de título o el nombre de archivo de la etiqueta
ID3).
Pioneer
Además, durante la reproducción de archivos MP3, se visualizará la
velocidad en bits después del nombre de pista.
When an artist name is selected in TEXT display, the [ ] icon will be
displayed followed by the artist’s name.
Pioneer DJ
29
<DRB1398> En/Sp
Advanced Operations/Operaciones avanzadas
30
En/Sp <DRB1398>
Before
Advanced
Operating
Operations
(Names/Operaciones
and Functions
avanzadas
of Parts)
English
then release your hand from the jog dial. ¶ Cuando se presiona el botón PLAY/PAUSE (6) otra vez para
reanudar la reproducción, el sonido se acelera a la velocidad ajustada
con el mando VINYL SPEED ADJUST RELEASE/START.
Braking
¶ During playback in VINYL mode, if the PLAY/PAUSE button (6) is Reproducción de bucle
pressed to pause playback, the sound decelerates at the braking speed
set with the VINYL SPEED ADJUST TOUCH/BRAKE dial. 7 Definición de un bucle
¶ When the PLAY/PAUSE button (6) is pressed once again to resume 1. Presione el botón PLAY/PAUSE (6) para iniciar la
playback, the sound accelerates at the speed set with the VINYL reproducción.
Español
SPEED ADJUST RELEASE/START dial. 2. Durante la reproducción o en estado de pausa, presione
el botón LOOP IN/REALTIME CUE.
Loop playback ¶ Esta operación no será necesaria si ya se ha ajustado un punto de
localización previamente grabado como el punto de inicio del bucle.
7 Defining a loop
3. Cuando la reproducción llegue al punto salida del bucle
1. Press the PLAY/PAUSE button (6) to begin playback.
deseado, presione el botón LOOP OUT.
2. During playback or pause, press the LOOP IN/REALTIME
¶ La reproducción se iniciará entre el punto de entrada del bucle y el
CUE button. de salida del bucle.
¶ This operation is not required if a prerecorded cue point has al- ¶ Durante la reproducción de archivos MP3, el bucle sólo puede
ready been set as the loop start point. ajustarse entre puntos ajustados dentro de la misma pista.
3. When playback reaches the desired loop-out point, press ¶ Cuando se haya ajustado el bucle, se encenderá el botón RELOOP/
the LOOP OUT button. EXIT.
¶ Playback will begin between the loop-in and loop-out points.
¶ During MP3 play, the loop can be set only between points set 7 Para cancelar un bucle
within the same track. Durante la reproducción de bucle, presione el botón RELOOP/
¶ When the loop has been set, the RELOOP/EXIT button lights. EXIT.
¶ Cuando la reproducción llegue al punto de salida del bucle, continuará
7 To cancel a loop con normalidad, sin volver al punto de entrada del bucle.
During loop playback, press the RELOOP/EXIT button.
¶ When the playback reaches the loop-out point, it will continue nor- 7 Para cambiar un punto de entrada de bucle
mally, without returning to the loop-in point. 1. Durante la reproducción de bucle, presione el botón LOOP
IN/REALTIME CUE (IN ADJUST).
7 To change a loop-in point ¶ El visualizador mostrará el tiempo del punto de entrada; el botón
1. During loop play, press the LOOP IN/REALTIME CUE (IN LOOP IN/REALTIME CUE empezará a parpadear con rapidez y se
ADJUST) button. apagará la luz del botón LOOP OUT.
¶ The display will show the in-point time; the LOOP IN/REALTIME 2. Presione el botón SEARCH (1, ¡) o gire el mando de
CUE button will change to quick flashing, while the LOOP OUT lanzadera.
button light will go out. ¶ El punto de entrada de bucle cambiará en incrementos de una trama.
2. Press the SEARCH button (1, ¡) or rotate the jog dial. El margen permisible para ajustar un punto de entrada es de ±30
¶ The loop-in point will change in one-frame increments. The per- tramas, y debe ajustarse antes de cualquier punto de salida.
¶ En el caso de archivos MP3, el ajuste de las posiciones del bucle
missible range for adjusting an in point is ±30 frames, and it must
sólo podrá efectuarse dentro de la misma pista en la que se
be set before any out point.
ajustaron los puntos de localización.
¶ In the case of MP3, adjustment of loop positions is possible only
¶ Los puntos de entrada de bucle no podrán modificarse durante la
within the same track where cue points are set. reproducción en inversión ni reproducción rascada.
¶ Loop-in point cannot be modified during reverse play and scratch ¶ Cuando se presiona el botón LOOP IN/REALTIME CUE o después
play. de haber transcurrido 30 segundos, se cancela el modo de ajuste
¶ When the LOOP IN/REALTIME CUE button is pressed or 30 sec- y se reanuda la reproducción de bucle.
onds elapses, the adjustment mode is canceled and loop play
resumes. 7 Para cambiar un punto de salida de bucle
1. Durante la reproducción de bucle, presione el botón LOOP
7 To change a loop-out point OUT (OUT ADJUST).
1. During loop play, press the LOOP OUT (OUT ADJUST) ¶ El visualizador mostrará el tiempo del punto de salida; el botón
button. LOOP OUT empezará a parpadear con rapidez y se apagará la luz
¶ The display will show the out-point time; the LOOP OUT button del botón LOOP IN/REALTIME CUE.
will change to quick flashing, while the LOOP IN/REALTIME CUE 2. Presione el botón SEARCH (1, ¡) o gire el mando de
button light will go out. lanzadera.
2. Press the SEARCH button (1, ¡) or rotate the jog dial. ¶ El punto de salida de bucle cambiará en incrementos de una trama.
¶ The loop-out point will change in one-frame increments. ¶ El punto de salida de bucle no podrá moverse a una posición ante-
¶ The loop-out point cannot be moved to a position before the loop- rior al punto de entrada de bucle.
in point. ¶ En el caso de archivos MP3, el ajuste de las posiciones del bucle
¶ In the case of MP3, adjustment of loop positions is possible only sólo podrá efectuarse dentro de la misma pista en la que se
within the same track where cue points are set. ajustaron los puntos de localización.
¶ Loop-out point cannot be modified during reverse play and scratch ¶ Los puntos de salida de bucle no podrán modificarse durante la
play. reproducción en inversión ni reproducción rascada.
¶ When the LOOP OUT button is pressed or 30 seconds elapses, ¶ Cuando se presiona el botón LOOP OUT o después de haber
the adjustment mode is canceled and loop play resumes. transcurrido 30 segundos, se cancela el modo de ajuste y se
reanuda la reproducción de bucle.
31
<DRB1398> En/Sp
Advanced Operations/Operaciones avanzadas
32
En/Sp <DRB1398>
Before
Advanced
Operating
Operations
(Names/Operaciones
and Functions
avanzadas
of Parts)
English
fader can also be used to control fader start on the player. Also, when de lanzadera funcionará al revés.
the fader lever is returned to its original position, the player can be made ¶ Durante la reproducción en inversión, no será posible crear nuevos
to return to its cue point (back cue). For details regarding connection, bucles ni editar puntos de salida de bucle.
☞ P. 13. ¶ Cuando realice la búsqueda de pistas o la reproducción de bucle, el
indicador de estado de la memoria de audio (visualización del mando
Relay play using two players de lanzadera) parpadeará durante 1 a 2 segundos, y es posible que
When the accessory control cord is used to connect the CONTROL jacks las operaciones de rascado/inversión queden temporalmente
of this player and another Pioneer CDJ series CD player, the two players inhabilitadas.
¶ En el caso de archivos MP3, no podrá efectuarse la reproducción en
Español
can be made to perform automatic relay play (☞ P. 14).
¶ Set the two players’ auto cue function to ON (the [A.CUE] indicator inversión si abarca varias carpetas.
lights in the display). ¶ Durante la reproducción de archivos MP3, es posible que la reproducción
¶ Set your audio mixer’s fader control to its center position. en inversión no se realice inmediatamente con algunas pistas.
1. Begin playback on the first player.
2. When the currently playing track finishes, the second Acerca de la
player automatically begins playback. reproducción de inicio con fundido
3. The first player then pauses at the beginning of the its Cuando se emplea el cable de control accesorio para conectar la toma
next track in the CUE standby mode. CONTROL de esta unidad con la toma CONTROL correspondiente de
¶ This process is repeated automatically, alternating playback on both una consola de mezcla para DJ Pioneer, al mover el atenuador de ca-
players. nales de la consola de mezcla se libera la espera de CUE del reproductor
¶ By exchanging the disc on the waiting player and cueing it to a de discos CD, y se inicia instantáneamente la reproducción. El fundido
desired track, you can play a continuing series of desired tracks cruzado de la consola de mezcla también podrá utilizarse para controlar
from different discs. el inicio con fundido en el reproductor. Además, cuando se repone la
¶ By setting a cue point on the waiting player, it is possible to start palanca de fundido a su posición original, el reproductor podrá hacerse
from playback from a specifically desired point on a track ☞ P. 25 retornar a su punto de localización (localización regresiva). Para más
“Cue point settings”. detalles relacionados con la conexión, ☞ P. 13.
Reproducción por
Note: relevos con dos reproductores
¶ Relay play may not occur properly if both players’ audio out- Cuando se emplea el cable de control accesorio para conectar las tomas
put connectors are not connected to the same audio mixer. CONTROL de este reproductor y de otro reproductor de discos CD de la
¶ If the power is disconnected to the currently operating player, serie CDJ Pioneer, podrá realizarse la reproducción automática por relevos
the waiting player may start playback in some cases. con los dos reproductores (☞ P. 14).
¶ Since the control cords require different connections, it is ¶ Active (ON) la función de localización automática de ambos
not possible to combine fader start and relay play simulta- reproductores (el indicador [A.CUE] se encenderá en el visualizador.)
neously. ¶ Ponga el control de fundido de la consola de mezcla de audio en su
posición central.
1. Inicie la reproducción en el primer reproductor.
2. Cuando finalice la pista actualmente en reproducción, el
otro reproductor iniciará automáticamente la reproducción.
3. El primer reproductor se establecerá entonces en el modo
de pausa al principio de la pista siguiente de su disco en
el modo de espera de localización (CUE).
¶ Este proceso se repite automáticamente, alternando la
reproducción de ambos reproductores.
¶ Reemplazando el disco del reproductor en espera y localizando en
él la pista deseada, podrá reproducir continuamente una amplia
variedad de pistas seleccionadas de distintos discos.
¶ Ajustando un punto de localización en el reproductor en espera, la
reproducción podrá ajustarse para que comience desde un punto
especialmente seleccionado de una pista ☞ P. 24 “Ajustes de
puntos de localización”.
Nota:
¶ La reproducción por relevos puede no realizarse adecuada-
mente si los conectores de salida de audio de los dos
reproductores no están conectados a la misma consola de
mezcla de audio.
¶ Si se interrumpe la alimentación del reproductor actual-
mente en reproducción, el otro reproductor podrá iniciar
automáticamente la reproducción en algunos casos.
¶ Puesto que es necesarios efectuar distintas conexiones con
los cables de control, no es posible combinar el inicio con
fundido simultáneamente con la reproducción por relevos.
33
<DRB1398> En/Sp
Operations Using Memory Cards/Operaciones utilizando tarjetas de memoria
Superficie de la
Memory card
tarjeta hacia arriba
Memory card door
Open the memory card door, and insert the memory card, label side up Tarjeta de memoria
and with the beveled edge toward the front. Insert the card slowly, hold- Puerta de la tarjeta de memoria
ing it flat, and push it in until it stops. Shut the memory card door.
The display will show [SD CARD] (for cards conforming to the SD memory
Abra la puerta de la tarjeta de memoria, e inserte la tarjeta de memoria,
card standard) or [CDJ CARD] (for cards formatted with the CDJ-1000 or
con el lado de la etiqueta arriba y con el borde biselado hacia delante.
CDJ-1000MK2), followed by the number of discs recorded on the card.
Inserte lentamente la tarjeta, manteniéndola plana, y empujándola hasta
¶ Removing the memory card el tope. Cierre la puerta de la tarjeta de memoria.
Open the memory card door and wait until the CARD indicator lamp El visualizador mostrará [SD CARD] (para tarjetas de la norma de tarjetas
goes out, then press in the memory card slightly and allow it to eject; de memoria SC) o [CDJ CARD] (para tarjetas formateadas con el CDJ-
grasp the end of the card and pull out carefully. 1000 o CDJ-1000MK2), seguido del número de discos grabados en la
tarjeta.
34
En/Sp <DRB1398>
Operations Using Memory Cards/Operaciones
Before Operating (Names
utilizando
andtarjetas
Functions
de memoria
of Parts)
English
drop them, or subject them to strong forces or impacts. Also,
avoid using or storing memory cards in environments subject Notas:
to static electricity or electrical noise. ¶ No abra la puerta de la tarjeta ni desconecte la alimentación
¶ Memory cards can be broken when subjected to impacts or mientras el indicador CARD esté parpadeando, porque podrían
static electricity. Be very careful when handling them, and make dañarse los datos grabados.
regular backups of important recorded data (☞ P. 37). ¶ Las tarjetas de memoria son dispositivos electrónicos de
Pioneer disclaims any responsibility for damage to or loss of precisión. No las doble, no deje que se caigan, ni las someta a
memory card data, or other incidental damages arising from presión o impactos fuertes. Además, evite utilizar y guardar
such loss. tarjetas de memoria en entornos sometidos a la electricidad
Español
estática o a ruido eléctrico.
¶ Las tarjetas de memoria pueden romperse si se someten a
golpes o a la electricidad estática. Tenga mucho cuidado cuando
CUE/LOOP las maneje, y haga copias de seguridad de los datos importantes
MEMORY grabados a intervalos regulares (☞ P. 37).
Pioneer no se hará responsable por los daños que pueda sufrir
CUE/LOOP la tarjeta ni por la pérdida de datos de las tarjetas de memoria,
DELETE
ni por otros daños que pueda causar tal pérdida.
CUE/LOOP
CALL
2, 3
To copy memory card data Para copiar datos de una tarjeta de memoria
1. With no disc or memory card loaded: 1. Sin haber cargado disco ni tarjeta de memoria:
Hold the CUE/LOOP MEMORY button pressed for 5 sec- Mantenga presionado el botón CUE/LOOP MEMORY
onds or more. durante 5 segundos o más.
¶ En el visualizador se desplazarán los mensajes [COPY MODE]
English
¶ The display will scroll the [COPY MODE] [CARD A IN] messages.
2. Insert the original source memory card into the memory [CARD A IN].
2. Inserte la tarjeta fuente original en la ranura de inserción
card slot.
de la misma.
¶ The display will show the [READING] message; after several min-
¶ El visualizador mostrará el mensaje [READING], y después de
utes, the [CARD B IN] message will appear. varios minutos, aparecerá el mensaje [CARD B IN].
3. Remove the source card and insert the target memory 3. Extraiga la tarjeta fuente e inserte la tarjeta de memoria
card. de destino.
¶ Be sure to delete earlier contents of the target card to provide ¶ Cerciórese de borrar antes el contenido de la tarjeta de destino
sufficient recording capacity. para disponer de suficiente capacidad de grabación.
Español
¶ The display will show the [WRITING] message, and after several ¶ El visualizador mostrará el los mensaje [WRITING], y después de
minutes, the [CARD A IN] message will appear. varios minutos, aparecerá el mensaje [CARD A IN].
4. Remove the target card, and once more insert the origi- 4. Extraiga la tarjeta de destino, y vuelva a insertar la tarjeta
nal source card. fuente original.
¶ The display will show the [READING] message; after several min- ¶ El visualizador mostrará el mensaje [READING], y después de
varios minutos, aparecerá el mensaje [CARD B IN].
utes, the [CARD B IN] message will appear.
5. Repita los pasos 3 y 4 cuantas veces haga falta.
5. Repeat steps 3 and 4 as required.
¶ El proceso de copia se completará cuando el visualizador muestre
¶ The copying process is completed when the display shows the el mensaje [COMPLETE].
[COMPLETE] message. ¶ La copia de una tarjeta de memoria SD de 32 MB llena requerirá
¶ Copying of a full 32MB SD memory card will require a maximum un máximo de 4 ciclos de los pasos 3 y 4 de grabación.
of 4 cycles of recording steps 3 to 4. ¶ Si la tarjeta de destino tiene insuficiente capacidad de memoria para
¶ If the target card has insufficient memory capacity to complete the completar el proceso, aparecerá el mensaje [CAPACITY ERROR].
copying process, the [CAPACITY ERROR] message will appear.
¶ Si usted posee un ordenador con unidad de lectura/escritura de tarjetas
de memoria, podrá utilizar la unidad de lectura/escritura para copiar sus
¶ If you possess a computer with memory card reader/writer, the reader/ tarjetas de memoria SD. (Las tarjetas de memoria MultiMedia
writer can be used to copy your SD memory cards. (MultiMedia Cards formateadas en un CDJ-1000 o CDJ-1000MK2 no podrán copiarse
formatted on the CDJ-1000 or CDJ-1000MK2 cannot be copied using empleando un ordenador.) ☞ P. 34, Precauciones relacionadas con el
a computer.) formateo de tarjetas de memoria.
☞ P. 34, precautions regarding memory card formatting.
Visualización durante la grabación de
Display during recording of cue and loop puntos de localización y de bucle
points
Mensaje del
Significado
Display Message Meaning visualizador
[CARD MEMORY] Cue point or loop point has been success- [CARD MEMORY] El punto de localización o punto de bucle
ha sido almacenado con éxito en la tarjeta
fully stored in the memory card.
de memoria.
[CANNOT MEMORIZE Displayed during MP3 playback when a [CANNOT MEMORIZE Se visualiza durante la reproducción de
ON THIS CARD] card formatted on the CDJ-1000 or CDJ- ON THIS CARD] archivos MP3 cuando se ha insertado una
1000MK2 has been loaded and recorded tarjeta formateada con el CDJ-1000 o CDJ-
operations are performed. Point data 1000MK2 y se efectúan las operaciones
cannot be recorded to the card. grabadas. Los datos de puntos no están
grabados en la tarjeta.
[CARD FULL] Insufficient space remains on the memory
[CARD FULL] Queda insuficiente espacio en la tarjeta de
card. Point data is not recorded to the card. memoria. Los datos de puntos no están
[CARD PROTECTED] The memory card’s LOCK (wrote protect) grabados en la tarjeta.
function is enabled, and point data cannot [CARD PROTECTED] La función de bloqueo (LOCK) (protección
be written to the card. contra escritura) de la tarjeta de memoria
está habilitada, y no pueden escribirse
[INTERNAL MEMORY] No memory card is loaded. datos de puntos en la tarjeta.
followed by [NO CARD]
[INTERNAL MEMORY], No hay tarjeta de memoria cargada.
[INTERNAL MEMORY] A memory card is loaded, but the memory seguido por [NO CARD]
followed by [CLOSE card door has not been closed. Close the [INTERNAL MEMORY], Hay una tarjeta de memoria cargada, pero
CARD DOOR] door and retry. seguido por [CLOSE no se ha cerrado la puerta de la tarjeta de
CARD DOOR] memoria. Cierre la puerta y vuelva a
[UNFORMAT] The loaded memory card does not intentarlo.
conform to SD memory card standards, or
[UNFORMAT] La tarjeta de memoria cargada no cumple
to CDJ-1000, CDJ-1000MK2 (MMC)
las normas de tarjetas de memoria SD, o
formatting standards. Point data cannot las normas de formateado de los CDJ-
be recorded to the card. 1000 ó CDJ-1000MK2 (MMC). Los datos
[CARD ERROR] The loaded memory card appears to be de puntos no están grabados en la tarjeta.
damaged. [CARD ERROR] Parece ser que la tarjeta de memoria
cargada está dañada.
[POINT FULL] The total number of recorded cue points
and loop points has reached 100. [POINT FULL] El número total de puntos de localización
grabados ha llegado a los 100.
Insert memory card when recording cue point data, loop point data, hot Inserte la tarjeta de memoria para grabar datos de puntos de localización,
cue data, or WAVE data. If no memory card is loaded, point data will be datos de puntos de bucle, datos de localización rápida, o datos WAVE. Si
lost in the event the power is turned off or the current disc is removed. no se carga ninguna tarjeta de memoria, los datos de los puntos se
perderán si se desconecta la alimentación o si se extrae el disco actual.
37
<DRB1398> En/Sp
Troubleshooting
Troubleshooting
Incorrect operations can be mistaken as malfunctions. If you believe the unit is not operating correctly, consult the chart below. Sometimes incorrect
operation may be due to a malfunction in another component. If the problem is not fixed, check the other components used with the player. If the
problem still persists, contact your nearest Pioneer authorized service center or dealer for service.
38
En <DRB1398>
Before Operating (Names and
Solución
Functions
de problemas
of Parts)
Solución de problemas
Las operaciones incorrectas pueden confundirse con mal funcionamiento. Si cree que su unidad no está funcionando correctamente, consulte la tabla
siguiente. Algunas veces el funcionamiento incorrecto puede deberse a un mal funcionamiento en otro componente. Si no puede solucionar el problema,
compruebe los demás componente utilizados con el reproductor. Si el problema persiste, póngase en contacto con el centro de servicio autorizado por
English
Pioneer más cercano o con su proveedor Pioneer.
Español
botón EJECT (0).
La reproducción no se inicia ni ¶ La función de localización automática está ¶ Mantenga presionado el botón TIME MODE/
cuando se inserta un disco. activada. AUTO CUE durante 1 segundo o más para
desactivar la función de localización automática.
La reproducción se para ¶ El disco está cargado al revés. ¶ Cargue correctamente el disco con la cara de
inmediatamente después de la etiqueta arriba.
haberse iniciado. ¶ Hay suciedad en el disco, etc. ¶ Limpie la suciedad del disco.
Los archivos MP3 no pueden ¶ El formato es erróneo. ¶ Vea la sección de “Reproducción de archivos
reproducirse. MP3” en la página 11.
No pueden buscarse pistas MP3. ¶ Se ha intentado la búsqueda (avance rápido/ ¶ La búsqueda de archivos MP3 sólo puede
inversión rápida) de archivos en una carpeta distinta. efectuarse dentro de la misma carpeta.
No se oye el sonido. ¶ Los cables de salida no están correctamente ¶ Vuelva a comprobar las conexiones.
conectados o están aflojados.
¶ Operación inapropiada de la consola de mezcla de ¶ Compruebe los ajustes de los interruptores y
audio. controles de volumen del sonido de la consola
de mezcla de audio.
¶ Las clavijas y/o los terminales están sucios. ¶ Limpie la suciedad.
¶ El reproductor se encuentra en el modo de pausa. ¶ Presione el botón PLAY/PAUSE (6).
El sonido sale distorsionado, se oye ¶ Los cables de salida no están correctamente ¶ Conecte a los terminales LINE INPUT de la
ruido. conectados o están aflojados. consola de mezcla de audio. (No realice la
conexión a los terminales MIC.)
¶ Las clavijas y/o los terminales están sucios. ¶ Limpie la suciedad.
¶ Se capta interferencia de un televisor. ¶ Apague el televisor, o aleje el reproductor del
televisor.
Con ciertos discos, se produce un ruido ¶ El disco está rayado o deformado. ¶ Reemplace el disco.
fuerza o se detiene la reproducción. ¶ El disco está muy sucio. ¶ Limpie el disco.
Cuando se activa (ON) la función de ¶ Si la parte con sonido silenciado entre piezas es ¶ Mantenga presionado el botón TIME MODE/
localización automática, la búsqueda larga, se alargará el tiempo de búsqueda. AUTO CUE durante más de 1 segundo para
de pistas no finaliza. (Si el punto de localización no puede encontrarse desactivar (OFF) la función de localización
antes de diez segundos, el punto de localización automática.
se ajusta al principio de la pista.)
La función de localización regresiva ¶ Todavía no se ha ajustado el punto de localización. ¶ Ajuste un punto de localización. (Vea la página
no puede efectuarse aunque se ¶ En el caso de archivos MP3, la localización 24.)
presione el botón CUE en el modo regresiva no puede efectuarse si no hay ningún
de reproducción. punto de localización dentro de la carpeta que
actualmente se está reproduciendo.
Al presionar el botón LOOP OUT no ¶ No se han ajustado puntos de localización (puntos ¶ Ajuste un punto de localización.
se inicia la reproducción de bucle. de entrada de bucle).
¶ En el caso de archivos MP3, el bucle no puede
efectuarse si no hay ningún punto de entrada de
bucle dentro de la pista que actualmente se está
reproduciendo.
El mando de lanzadera no funciona ¶ El modo JOG MODE [VINYL/CDJ] se ha ajustado ¶ Presione el botón JOG MODE SELECT para
como se desea. incorrectamente. ajustar el modo deseado de JOG MODE
[VINYL] o [CDJ].
La imagen de la pantalla de TV ¶ Se capta interferencia del reproductor de discos ¶ Desconecte el interruptor de alimentación
fluctúa o la difusión de FM tiene CD. POWER del reproductor, o aleje el reproductor
interferencias de ruido. del televisor o sintonizador.
No gira el disco cuando se conecta ¶ La rotación del disco se detiene automáticamente ¶ La reproducción puede iniciarse presionando el
la alimentación. si no se ha efectuado ninguna operación durante botón PLAY/PAUSE (6). Presione el botón
100 o más minutos en el modo de pausa. EJECT (0) para expulsar el disco.
¶ Después de haber terminado la reproducción de
la última pista del disco, si la visualización [END]
prosigue durante 100 minutos sin introducir
ninguna otra operación, la rotación del disco se
detendrá automáticamente.
39
<DRB1398> Sp
Troubleshooting (Error message display)
¶ This component may fail to operate properly due to influence of static electricity or other external influences. In this case, try turning
off the POWER switch, and turn on the power again only when the disc has fully stopped rotating.
¶ This unit cannot play partially recorded CD-R or CD-RW discs that have not been finalized.
¶ This unit plays only standard 12 cm discs and 8 cm discs mounted in proper disc adapters; it cannot play irregularly shaped discs
(damage or malfunctions may occur).
¶ When playing 8 cm discs mounted on adapters, some speed loss may be experienced when using scratch and reverse operations.
This unit for high performance when rotating discs at high speed, but when 8 cm discs are mounted in adapters, the rotation speed
is reduced for safety. This is not a malfunction.
¶ BPM values measured with this unit may differ from published values found on CD labels, or those measured on Pioneer DJ mixers.
This is a result of differences in BPM measuring methods, and is not a malfunction.
¶ When playing CD-R/RW discs, some degradation in performance may be experienced depending on the recording quality of the
individual disc.
E–72 01 TOC READ ERROR Can’t read TOC data. Disc is cracked.
= Replace disc.
E–83 01 PLAYER ERROR Can’t play this disc properly. Disc is dirty.
E–83 02 = Clean disc.
E–83 03 If other discs operate normally, problem is with
this disc.
E-83 04 MP3 DECODER ERROR Can’t play this disc properly. Does not conform to MP3 format.
= Change to disc conforming to MP3 format.
E-83 05 DATA FORMAT ERROR
E–91 01 MECHANICAL TIME OUT Mechanical operation did not end within Foreign object in disc loading slot.
specified time. = Remove foreign object.
40
En <DRB1398>
Solución de problemas (Visualización de mensajes de error)
English
cargado una tarjeta MultiMedia grabada con el con un CDJ-1000 o CDJ-1000MK2 no puede
CDJ-1000 o CDJ-1000MK2. utilizarse para la grabación durante la
reproducción de archivos MP3.
¶ La tarjeta de memoria SD no está apropiadamente ¶ Inserte una tarjeta de memoria formateada
formateada. según las normas de tarjetas de memoria SD.
¶ La puerta de la tarjeta de memoria está abierta. ¶ Cierre la puerta de la tarjeta de memoria.
¶ Este componente falla en funcionar adecuadamente debido a la influencia de la electricidad estática o de otras influencias externas.
En este caso, pruebe desconectando y volviendo a conectar la alimentación solamente cuando el disco haya dejado completamente
Español
de girar.
¶ Este reproductor no podrá reproducir discos CD-R ni CD-RW parcialmente grabados que no se hayan finalizado.
¶ Este reproductor solamente podrá reproducir discos estándar de 12 cm y discos de 8 cm montados en adaptadores de discos
apropiados; no podrá reproducir discos de forma irregular (se podrían producir daños y mal funcionamiento).
¶ Cuando reproduzca discos de 8 cm montado en adaptadores, es posible que se experimente cierta pérdida de velocidad cuando se
utilicen las operaciones de reproducción con rascado y reproducción regresiva. Esta unidad ofrece un gran rendimiento haciendo
girar los discos a alta velocidad, pero cuando los discos de 8 cm están montados en adaptadores, la velocidad de rotación se reduce
por motivos de seguridad. Esto no significa mal funcionamiento.
¶ Los valores de BPM medidos con esa con esta unidad pueden diferir de los publicados en las etiquetas de los discos CD, o de los
medidos en los mezcladores para DJ Pioneer. Éste es el resultado de las diferencias en los métodos de medición de BPM, y no
significa mal funcionamiento.
¶ Cuando reproduzca discos CD-R/RW, es posible que experimente cierta degradación en el rendimiento dependiendo de la calidad
de cada disco individual.
E–72 01 TOC READ ERROR No es posible leer los datos de la TOC. El disco está rajado.
= Reemplace el disco.
E–83 01 PLAYER ERROR No es posible reproducir adecuadamente El disco está muy sucio.
E–83 02 este disco. = Limpie el disco.
E–83 03 Si otros discos funcionan normalmente, el
problema estará en este disco.
E-83 04 MP3 DECODER ERROR No es posible reproducir adecuadamente No cumple las normas del formato MP3.
este disco. = Cambie a otro disco que cumpla las normas
E-83 05 DATA FORMAT ERROR del formato MP3.
E–91 01 MECHANICAL TIME OUT La operación mecánica no finalizó dentro del Objetos extraños en la ranura de inserción del
tiempo especificado. disco.
= Elimine los objetos extraños.
41
<DRB1398> Sp
感謝您購買本Pioneer產品。
請詳讀這些操作說明,這樣您才能瞭解如何正操作本產品。完成閱讀操作說明後,請將操作手冊放在安全的位置供將來參考時使用。
在有些國家或地區中,電源插頭和電源開關的形狀有時和說明圖片顯示的不同。但是連接和操作方法相同。
AC電源線
所能使用的電源線需視各地區或國家中的電壓而定。若是使用不當,則可能會導致起火或引發
其他危險,故請確實使用正確的電源線(請參閱以下說明)。
AC電源線及轉換插頭的使用
地區 插頭型式
歐規地區
注意
此種電源線切勿在台灣使用。
歐規雙腳插頭
台灣專用
注意
僅限於台灣使用。
在其他地區,請勿使用。
台規雙腳扁平插頭
42
ChH <DRB1398>
目錄/規格
目錄
操作之前 進階操作
規格 ................................................ 43 進階操作 ............................................ 58
特點 ................................................ 44 刮片播放(Scratch Play) ........................... 58
處理方面之安全須知 .................................. 45 旋轉播放(Spin Play) .............................. 58
可配合本機使用的光碟 ................................ 46 煞速(Braking) .................................... 58
接線 ................................................ 48 循環播放 ......................................... 58
控制元件名稱及功能 .................................. 50 欲執行熱點提示(hot cue)時 ........................ 59
反向播放 ......................................... 59
基本操作 關於淡化器啟動(fader start)播放 .................. 59
利用兩台雷射唱機進行接續播放(relay play) ......... 59
置入及取出光碟 ...................................... 53
使用記憶卡操作 ...................................... 60
DJ雷射唱機的操作 .................................... 54
錄到記憶卡上 ..................................... 60
自動提示功能(Auto cueing) ........................ 54
欲叫出所錄資料 ................................... 61
開始播放 ......................................... 54
欲刪除錄在記憶卡上的資訊時 ....................... 61
欲停止播放時 ..................................... 54
欲複製記憶卡上資料 ............................... 61
欲暫停播放時 ..................................... 54
提示及循環點錄製期間的顯示 ....................... 61
向前快轉/向後快轉 ................................ 54
音軌搜尋 ......................................... 55
資料夾搜尋(僅限MP3) .............................. 55 其他
提示點設定 ....................................... 55 故障排除 ............................................ 62
欲變更播放速度時 ................................. 56
應用主要節拍控制功能 ............................. 56
飛梭轉盤功能 ..................................... 56
飛梭靈敏度調整 ................................... 56
混合不同音軌 ..................................... 57
關於WAVE音階顯示 ................................. 57
關於TEXT文字顯示 ................................. 57
規格
1. 一般 3. 配件
系統 .................................... CD數位音響系統 ÷ 操作手冊 ........................................... 1
電源需求 ................... AC 110 V 至 240 V, 50/60 Hz ÷ 電源線(☞第42頁) ................................... 2
功率消耗 .......................................... 27 W ÷ 音頻線 ............................................. 1
操作溫度 ............................... +5 ℃ 至 +35 ℃ ÷ 控制線 ............................................. 1
操作濕度 ................ 5 % 至 85 % (不得有濕氣形成。) ÷ 強制退出針
重量 ........................................... 4.2公斤 (置於底部面板中的凹槽內) ........................... 1
尺寸 ................... 320(寬) X 370(深) X 105(高)釐米 ÷ SD記憶卡 ........................................... 1
2. 聲音部份 備註:
規格與設計如有變更,恕不另行通知。
頻率響應 ................................ 4 Hz 至 20 kHz
信噪比 ............................... 115 dB以上(JEITA)
失真度 .................................. 0.006 %(JEITA)
43
<DRB1398> ChH
特點
特點
CDJ-1000MK3 雷射唱機是專為DJ使用而設計,能提供DISCO舞廳專 ¶ 節拍控制範圍(TEMPO CONTROL RANGE)
用的所有功能和演出效果,且所提供的演出效果、音質及功能性 最大變動範圍可設定為四個變動範圍:± 6%、±10 %、±16 %
絕對優於任何一種類比播放器。 及WIDE以加速調整。
¶ 節拍控制鈷設(TEMPO CONTROL RESET)
飛梭轉盤(JOG DIAL) 可無視滑桿的位置,重新將節拍設定歸零(0 %)。
¶ 主要節拍控制(MASTER TEMPO)
206釐米的大直徑飛梭轉盤(Jog Dial)能讓類比唱盤的操作更加得 只改變音樂節拍而不改變音高。
心應手。
¶ 滑音控制(PITCH BEND)
本項功能讓您可根據飛梭轉盤旋轉的方向以及轉動的速度來改變
提示(CUE)
音樂的節拍。 ¶ 返回提示(BACK CUE)
¶ 刮片摭奏(SCRATCH PLAY) 在將提示點存入記憶體後,按下CUE鍵同時播放本機以回到提示點
在VINYL模式下,只要壓下飛梭轉盤的盤面,播放便能根據轉盤轉 並重新播放一次。
動的方向和速度時而中斷,時而繼續。當然,您也可以在按放之 ¶ 自動提示(AUTO CUE)
間創新DJ技術之時,來調整舞弄的方式。 就算音軌的音框(frame)各有差異,自動提示功能仍可自動找到歌
¶ 覓格彙尋(FRAME SEARCH) 曲的起點,讓播放者按下PLAY鍵立即開始播放。
讓您能在暫停模式下轉動飛梭轉盤時,逐格(1/75秒)的從暫停位 ¶ 提示點取樣器(CUE POINT SAMPLER)
置慢慢轉動碟盤。 只要(One touch)按一下就能將來自記憶提示點的聲音原音重現,
¶ 飛快搜尋(SUPER FAST SEARCH) 不僅可用來核對起點還能做為「取樣器」使用。
只要一邊按住SEARCH(手動搜尋)按鍵、TRACK SEARCH(音軌搜尋)
按鍵或FOLDER SEARCH(曲夾搜尋)按鍵的同時,又一邊轉動飛梭轉 即時連密循環播放(REAL TIME SEAMLESS LOOP)
盤,就能讓搜尋的速度遠比正常的搜尋、音軌搜尋或曲夾搜尋操
作來得更快。 本項功能可簡化設定和解除循環(releasing loop)的方式。本項
¶ 飛梭調整(飛梭靈敏度調整)(JOG ADJUST) 功能讓您可在播放一音軌的同時設定循環。也可將循環設定在音
本項功能讓您調整在轉動飛梭轉盤時所感覺到的阻力。 軌的結尾,好讓音軌欲罷不能。此外,加上ADJUST模式,按一下
就能調整「進入循環」(loop-in)和「退出循環」(loop-out)點,
進而促進循環的操作。
飛梭資訊顯示(ON JOG DISPLAY)
在飛梭轉盤中央會顯示關於光碟的情況、提示點位置、聲音記憶 重複循環播放(RELOOP)
狀態、飛梭轉盤的觸感以及VINYL模式等等的資訊。
讓您可不限次數地任意重複播放循環
在解除循環播放回到循環的起點時按下RELOOP鍵,巧妙的配合節
音階顯示(WAVE DISPLAY) 拍使用按(on)和放(off)的動作,便能創造出全新的音響效果。
此項顯示能讓您事前找到音軌之間的中斷點(breakpoint)並把它用
來做為混合點或曲終點,這與您藉由確認類比唱片軌槽中唱針位 播放位址(PLAYING ADDRESS)
置的方式,實有異同工之妙。
本條狀圖示提供一音軌播放進度的視覺呈現,讓您可以看見目前
所播放的位置,就如同藉由查看類比唱片唱針位置的方式一樣。
提示/循環記憶(CUE/LOOP MEMORY) 條狀進度圖的長度是目前播放到的位置,而閃爍的條狀則在事先
本機配備有一項功能可將每張光碟的提示點或循環點錄到SD記憶 告知音軌要播完了。
卡或MultiMedia Cards(MMC)上,然後在播放相關光碟的時候,就
可將所錄的資料叫出使用。 隨插即入(SLOT IN)
可以直接將光碟置入而不用打開蓋板或托盤,讓音軌的選擇更加
熱點提示(HOT CUE) 快速。
可預設多達三處的熱點提示(A、B、C),讓您能立即經從其中任何
一點位置來做播放。熱點提示功能不僅可用來錄製提示點,就連 淡化器啟動(FADER START)
循環點也可以。
在接上Pioneer DJ混音器(另售)時,混音器的淡化器操作便可用
來執行快速開始及返回提示(back cue)。
反向播放(REVERSE PLAY)
您可將DIRECTION開關撥至其前面位置([REV]位置),就可反向來播 多重讀取(MULTI READ)
放音樂。
可允許CD-R、CD-RW光碟(以音樂CD或MP3格式錄製)的播放。(請注
意有某些光碟可能因為各種光碟、錄影機的特性或光碟髒污和刮
節拍控制(TEMP CONTROL) 傷而無法正確播放。)
100 mm高精確速度滑桿結合0.02 %精確度的數位顯示(±6 %以內)
讓您能夠精確的控制速度,輕鬆又精確的調整節拍。 MP3 DJ播放(MP3 DJ PLAY)
錄在CD-ROM上的MP3檔案可以利用DJ功能播放。
44
ChH <DRB1398>
處理方面之安全須知
處理方面之安全須知
安裝位置 搬動本機
¶ 若打算長期置於擴大器或螢光燈等發熱來源上使用,將會對產 ■ 嚴禁於播放時搬動本機
品效能造成影響。請避免將雷射唱機置於發熱來源上。 播放時,光碟是以高速轉動;在播放時搬動雷射唱機可能會造成
¶ 播放器安裝請儘量遠離調諧器和電視機。安裝在這類設備附近 光碟刮傷或其他方面的損壞。
的播放器可能會產生雜音或降低畫面的品質。
雜音在接上室內天線時可能很明顯。此時,請確實改用室外天 ■ 有必要搬動機器時
線或是關閉雷射唱機的電源。 在搬動本機時,請事前先將光碟取出並切斷電源。若在當中還置
¶ 當在音量吵雜的環境中使用本機時,例如揚聲器的附近,可能 有光碟的情況下搬動本機,將可能會導致故障或損壞。
會產生跳音(sound skip)的現象。請將本機遠離本機安裝或是
降低聆聽音量。
¶ 將本機置於平坦而穩當的平台上。在策劃安裝位置時,請適當
關於攜行盒
注意以下安全須知: 飛梭轉盤的上半部配備有一觸控式開關。在將雷射唱機放入其攜
請確定雷射唱機,包含其視訊、音頻及電源線,不要碰到抖動中 行盒內時,請避免壓到飛梭轉盤。
的物品。任何不是經由絕緣體所傳來的抖動,都可能會造成跳片
的情形。在使用安裝於攜行盒中的雷射唱機時,須特別小心。 凝水
將本機從原先冰涼的環境帶到溫熱的室內或當溫度急遽上升時,
在本機內部即可能會形成凝水,進行影響其效能。此時,請將本
機靜置一小時或逐漸將室溫升高。
清潔雷射唱機
欲清潔雷射唱機時,請用擦亮劑或柔軟的乾布擦拭。對於頑垢,
切勿置於抖動中的
請將軟布沾以稀釋的中性溶劑(以5到6倍清水稀釋),再澈底擰乾,
物品上。
將髒污清除。再來用乾布將表面擦乾。請勿使用苯或稀釋劑揮發
液以免損壞本機。
關於讀取頭清潔劑
預留空間以供散熱
雷射唱機的讀取器在正常的使用下應不致會髒。若在某種情況
下,讀取頭沾上髒污而故障時,請您就近聯絡PIONEER授權服務中
心。雷射唱機的讀取頭清潔劑可於一般市面購得,但在使用上仍
須特別小心,有些可能會造成讀取頭損壞。
預留空間以供 預留空間以供
散熱 散熱 關於錄在記憶卡上的資料
使用者有責任定期備份記憶卡上的資料。Pioneer對於因播放器及記憶
卡的不相容問題、靜電或其他外力所造成記憶卡資料的損壞或遺失,或
其他意外的損壞,概不負責。
45
<DRB1398> ChH
可配合本機使用的光碟(可在本機上播放的光碟類型/播放MP3檔案)
可配合本機使用的光碟
可在本機上播放的光碟類型 備註:
¶ 有些在獨立式錄影機或電腦光碟機上錄製的CD-R/CD-RW光碟可
¶ 以下為會出現在光碟標籤、包裝或封套上的標示及圖標。
能會因為各種原因,包含光碟的特性、刮傷、髒污、雷射唱機
讀取頭髒污或凝水等等,而無法在本雷射唱機上播放。
可播放光碟的類型及圖標
¶ 某些在電腦光碟機可能無法在本台雷射唱機上播放,這須視錄
CD CD-TEXT (註1) CD-R (註2)
CD-RW (註2)
製所用的應用程式、其設定方式以及操作環境而定。請確定使
用正確的方式來格式化所用的光碟。關於細節,請向應用程式
的作者請教。
¶ 本機無法播放局部錄製,未做終結(finalized)的CD-R或CD-RW
光碟。
註1) 關於「文字」(TEXT)顯示
¶ 關於CD-R或CD-RW光碟處理的詳盡資訊,請參閱每種光碟所附的
字元的數量可以顯示多達到4 8個。當顯示的長度超出1 6 個字元
處理注意事項。
時,就會顯示捲動的畫面。所可顯示的只限於文數字元及一定數
量的符號。(☞第57頁)
■ 關於CD-R/CD-RW光碟
註2) CD-R/CD-RW光碟 由於CD-R/RW光碟的獨特結構,將光碟長時間在暫停(或提示待命)
本雷射唱機支援以音樂CD格式或MP3錄製的CD-R/CD-RW光碟的播 模式下停滯於某一點上,可能會使這些光碟變得難以從該位置播
放。 放。同樣的現象若是使用循環功能過度的播放光碟某一點時也可
* 相關細節請參閱您錄影機的操作手冊。 能會發生。
因此,建議使用者在播放含有重要資料的光碟時,能建立備份歸
在播放8公分CD時,請使用8公分CD轉換器(☞53頁) 檔光碟。
■ 關於DualDisc光碟
本產品為設計符合音樂CD的標準。如使用不符合這類音樂CD標準
的光碟,將不對操作或效能提供任何保證。
播放MP3檔案
MP3檔案須遵照以下所列的格式需求。
* CDJ-1000MK3不具「檔案排序」(File Sort)功能;音軌將會依照所錄次序播放。
* 可播放存在CD-ROM上的MP3檔案。無法播放存在SD記憶卡或MultiMedia cards(MMC)上的MP3檔案。
* 起動時間隨資料夾的數量而增加。
46
ChH <DRB1398>
可配合本機使用的光碟(光碟的處理)
光碟的處理
■ 手握光碟時,切勿摸到訊號面。請手握光碟兩邊或一邊和中間
的碟孔。
■ 光碟表面切勿貼上有膠的標籤或膠帶。另外,切勿刮傷或損壞
標籤。
■ 光碟在雷射唱機內部是高速旋轉。切勿使用壞了、龜裂或變形
的光碟。
■ 切勿播放形狀立異的光碟
¶ 切勿播放圓形以外形狀,如心形的光碟。否則可能會發生故
障。
■ 光碟的存放
¶ 光碟是以傳統類比音樂唱片所用同樣的塑材所製。請小心不要
讓光碟變形。請始終將光碟放入盒內垂直存放,避免置於高
熱、潮濕或極低溫的地方。避免將光碟留在車內;陽光直射的
車內會變得非常熱。
¶ 請確實閱讀並遵照光碟標籤上所列的安全注意事項。
■ 光碟的清潔
¶ 請始終用軟布由內往外輕輕將光碟擦拭乾淨。
¶ 在清潔光碟時,建議請使用一般市售的CD清潔工具組。
¶ 若光碟變得很髒,請將軟布沾水弄濕(再確實擰乾),然後輕輕
將髒污擦拭乾淨。再用另一塊軟質乾布將水滴擦乾。
¶ 切勿在光碟上使用唱片清潔噴劑或抗靜電清潔劑。嚴禁使用
苯、稀釋劑或其他揮發液來清潔光碟,否則可能會造成光碟表
面的損壞。
47
<DRB1398> ChH
接線
接線
在接線或更換接線之前,請始終先將電源關閉並脫離電源線。
1.連接至Pioneer DJ混音器(音訊輸出及控制接頭)
使用輔助音頻線,將白色插頭接至L(左聲道)插孔,而紅色插頭則接至R(右聲道)插孔。
此外,藉由接上所提供的控制線,DJ混音器便能用來控制本機淡化器啟動(fader start)播放和返回提示(back cue)的操作。
注意,數位接線方式僅限於配備有數位輸入接頭的混音器(DJM-800、DJM-1000型等)。
請使用一般市售的同軸數位連接線來將本機的DIGITAL OUT接頭連接至DJ混音器的DIGITAL IN接頭上。
DJM-800的連接範例:
DJM-800
SIGNAL GND DIGITAL IN
PHONO CD LINE CD
L L
CONTROL CONTROL
R R
DIGITAL DIGITAL
CD CD
一般市售的同軸數位訊號線
一般市售的同軸數位訊號線
隨附音頻線 隨附音頻線 隨附控制線
CDJ-1000MK3 CDJ-1000MK3
B A
隨附控制線
¶ 在連接至DJM-1000時,附屬的音頻線可以用來連接其中一組的CD/LINE接頭至雷射唱機A,然後將另一組CD/LINE接頭連接至第二台雷
射唱機B。在要進行數位化的音頻接線時,務須使用一般市售的同軸數位訊號連接線來將雷射唱機的DIGITAL OUT接頭連接至DJM-1000
混音器的其中一組DIGITAL IN接頭上(4至6)。
¶ 在連接至DJM-600、DJM-300或DJM-500時,請使用隨附的音頻線來連接CD1接頭至雷射唱機A,而CD2接頭則連接至雷射唱機B。
¶ 在連接至DJM-909或DJM-707時,請使用隨附的音頻線來連接CH1 CD接頭至雷射唱機A,而CH2 CD接頭則連接至雷射唱機B。
¶ 在連接至DJM-3000時,將雷射唱機A連接至CH-1 LINE 1,而雷射唱機B則連接至CH-2 LINE 3。
¶ 在連接本台雷射唱機至其他的混音器時,將雷射唱機的AUDIO OUT接頭連接至混音器的LINE IN或AUX IN接頭上。(★切勿連接至PHONO
接頭,因其可能會導致聲音失真或不正確的播放。)
48
ChH <DRB1398>
Before Operating (Names and Functions of Parts)
接線
2.連接控制線以進行重新播放(relay play)
藉由使用隨附控制連接兩台DJ雷射唱機的控制接頭,便能進行自動重新播放(automatic relay play)。(☞第59頁)
CDJ-1000MK3 CDJ-1000MK3
隨附控制線
3.連接其他設備
A 連接立體聲擴大器(不使用DJ混音器時)
連接至CD或AUX IN接頭
立體聲擴大器
(切勿連接至PHONO IN接頭)
CDJ-1000MK3
隨附音頻線
B 連接配備有DIGITAL IN接頭的設備
配備有DIGITAL IN接頭等的
CD錄音機或擴大器
一般市售的同軸數位訊號線 CDJ-1000MK3
¶ DIGITAL OUT接頭僅能產生音頻資料。(不含子碼;CD圖形不支援)。
視連接的CD錄音機或其他設備而定,某些錄製或相關功能可能會受到限制。關於細節,請參閱連接設備的操作手冊。
4.連接電源線
在完成其他所有的接線後,請將電源線(☞第42頁)一端連接至雷射唱機後方的AC插座上,另一端則連接牆上標準的AC插座上,或您擴大
器上的輔助電源插座。
49
<DRB1398> ChH
控制元件名稱及功能
控制元件名稱及功能
1 2 3 4 5 6 7 8 9 10 11
後面板
12
13
35 14
15
34
37 38 36
16 39 40
33
17
32
18
31 19
20
前面板
30
29
28 21
27 22
26 25 24 23 41 42 43 44
50
ChH <DRB1398>
Before Operating (Names and Functions
控制元件名稱及功能of Parts)
顯示窗
51 52 53 54 55 56 57 58 59 60 61 62
63 64 65 66
52
ChH <DRB1398>
Before Operating (Names and Functions
置入及取出光碟
of Parts)
置入及取出光碟
播放8公分CD片時之注意事項
1 在播放8公分CD片時,請確實使用8公分CD片專用的轉換器。在將
光碟置入播放器之前,請確認光碟已藉由正確扣上轉換器的固定
請將標籤面 扣完成固定。若誤將沒有使用轉換器的8公分CD片置入,請立即按
朝上置入 下EJECT(0)鍵,將光碟取出。若光碟在第一次按下EJECT(0)鍵時
未退出,則請再按一次。
2 僅限使用標有'圖標的8公分CD片轉換器(建議使用的相容轉換
器)。在將光碟裝到轉換器上時,請確認光碟可以轉動自如,且無
彎曲、變形。
請水平置入時
強制退出功能
1. 將後面板的POWER開關設定至ON將電源打開。 若在按下EJECT(0)鍵無法將光碟退或者當您無法將光碟取
出,請將隨附的退出針插入雷射唱機前面的強制退出孔內(如
在POWER開始撥至OFF時,切勿嘗試硬是將光碟插入槽內,此舉可能會 圖)並壓下以退出光碟。在使用強制退出功能時,請確實遵照
造成光碟或置入機件損壞。 隨附的注意事項。
1 關閉雷射唱機的電源並等候至少一分鐘。
2. 將光碟從置入槽中插入。
¶ 手拿光碟時標籤面朝上並平整的插入前面板上的光碟置入槽。
¶ 使用8公分光碟時,先將光碟放入轉換器內。 在關閉電源後立即使用強制退出功能可能引
發以下的危險:
本機為高速旋轉以提供高度的效能。在播放置於轉換器上的8公
¶ 光碟可能還在轉動的情況下退出,使人因而受傷。
分光碟時,為了安全起見,轉速會因刮片降低,反轉速度會更
¶ 光碟可能會因光碟夾發生不穩轉動而損壞。
低。
¶ 一次限置入一片。切勿嘗試同時間置入兩片以上,或已置入一片
時,再置入另一片。 2 僅限使用隨附的退出針來進行本項操作程序(切勿使用其他
¶ 在置入碟片時,切勿彎曲到光碟,或嘗試硬行將光碟置入機件內 針型物體)。強制退出針就在雷射唱機的底部。
部。另外,當置入機件開始將光碟拉入播放器內或退出光碟之時, 在將隨附的退出完全插入強制退出孔時,光碟就會從置入
切勿強制操控機件的動作,此舉可能會使光碟或置入機件損壞。 槽中退出大約5 mm至10 mm。這時便可用手指扣住然後取
3. 當將EJECT UNLOCK/LOCK開關設至[UNLOCK],按下EJECT(0)按鍵 出。
即可退出已置入的光碟。
當將EJECT UNLOCK/LOCK開關設至[LOCK],在播放期間按下PLAY/
PAUSE(6)鍵時可先停止光碟,然後請按下EJECT(0)按鍵。若
已設定好提示點,則在播放期間按下CUE鍵可啟動返回提示功
能,然後按下EJECT(0)按鍵將光碟退出。
¶ 按下此鍵時,光碟會停止轉動同時將光碟退出置入槽外部份。
備註:
切勿在[EJECT]燈亮時嘗試將光碟按回槽內。若在[EJECT]燈亮時將
強制退出孔
光碟按回,置入機件可能會停止動作。此時,請再按一次EJECT(0)
鍵,並在[EJECT]燈滅之前切勿嘗試重新置入光碟。
53
<DRB1398> ChH
DJ雷射唱機的操作
DJ雷射唱機的操作
MP3 FOLDER SEARCH EJECT UNLOCK/LOCK 欲停止播放時
TIME MODE |, \ EJECT 0
/ AUTO CUE 1. 在EJECT UNLOCK/LOCK開關設至[UNLOCK]時按下EJECT鍵(0)。
當EJECT UNLOCK/LOCK開關設至[LOCK],可於播放期間按下PLAY/
VINYL
SPEED PAUSE鍵(6),或當已有設定提示點,請在按下EJECT鍵(0)以
ADJUST 退出光碟之前,先按下CUE鍵(返回提示)。
TOUCH
LOOP IN/ /BRAKE ¶ 播放會停止且光碟會退出。
REALTIME
CUE VINYL ¶ 注意,CDJ-1000MK3上並未附有停止鍵。
SPEED
ADJUST
RELEASE
TRACK /START 恢復(Resume)功能
SEARCH CUE LOOP ¶ 當EJECT UNLOCK/LOCK開關設至[UNLOCK]位置,就算誤按EJECT鍵,若
4, ¢ CALL
SEARCH 2, 3 是快速按下PLAY/PAUSE鍵(在顯示窗中的[EJECT]燈亮之前),則本機將
1, ¡ 會恢復至EJECT鍵按下之前的狀態。然而,音頻便會在此段時間內停止
輸出。
CUE
¶ 在光碟退出後,若將光碟重新插入,本機便會回到光碟退出前的同一狀
PLAY/PAUSE 態(除了循環以外)。
6
¶ 光碟退出後,若是按下FOLDER SEARCH鍵(|、\)或TRACK SEARCH鍵
飛梭轉盤 (4、¢),恢復功能就會取消。
自動提示功能(Auto cueing)
欲暫停播放時
此項功能可自動將提示點(☞第55頁)就設定在置入光碟時或進行音軌搜尋
在播放期間,按下PLAY/PAUSE鍵(6)。
或切換音軌時,聲音實際開始的地方。
¶ PLAY/PAUSE鍵及CUE鍵的外圈將會閃爍,同時播放會中斷。
若搜尋持續10秒鐘後仍未找到該點位置,則提示點會設定在音軌的開頭
¶ 若再按下PLAY/PAUSE鍵,該鍵的外圈將會亮起,同時恢復播放。
處。
¶ 在CDJ模式下,中斷的播放聲音在暫停時仍會輸出。若您希望不要用聲
¶ 開啟或關閉自動提示功能
音輸出,請將混音器的輸出位準調低。
按下TIME MODE/AUTO CUE鍵並按住一秒以上不放即可開啟或關閉自動
¶ 在VINYL模式下,設定VINYL SPEED ADJUST TOUCH/BRAKE旋鈕可減緩
提示功能。
轉動的速度到完全暫停為止。順時針轉動旋鈕可減緩光碟的速度到暫停
在AUTO CUE功能啟用時,[A.CUE]燈即會亮起。
為止。
¶ AUTO CUE的開/關狀態會存入記憶體中並在即使在電源關閉時也能
¶ 在VINYL模式下,設定VINYL SPEED ADJUST RELEASE/START旋鈕可在
保存。
解除暫停時漸增光碟的轉速,一直到最大播放速度為止。順時針轉動旋
¶ 此功能可切換AUTO CUE位準。
鈕可漸增光碟的速度到最大速為止。
7 切換AUTO CUE位準
¶ 在將本機設定為暫停後,若後續100分鐘內沒有任何操作,光碟的轉動
1. 按下TIME MODE/AUTO CUE鍵5秒以上不放。 即會自動停止。此時,按下PLAY/PAUSE鍵將可使暫停的播放恢復。
¶ 顯示窗會顯示[A.CUE-60db] (在原始狀態下)。
2. 按下CUE LOOP CALL按鍵(2、3)以切換位準。
¶ 可選擇的有-36 dB、-42 dB、-48 dB、-54 dB、-60 dB、-66 dB、
向前快轉/向後快轉
-72 dB及-78 dB。 播放期間按下其中一個SEARCH鍵(1、¡)。
¶ 當按下TIME MODE/AUTO CUE鍵或已播放15秒,位準切換的模式便會 按住¡鍵可將光碟向前快轉;按住1鍵可將光碟向後快轉。
取消。 ¶ 播放MP3時,向前快轉/向後快轉僅限用於同一資料夾中的音軌。
¶ 即使您將電源關閉,所設定的位準仍會保存於記憶體中。 ¶ 播放MP3時,向前快轉/向後快轉的次數可能會視音軌而有所減少。
開始播放 7 飛快搜尋
轉動飛梭轉盤的同時按下其中一個 SEARCH鍵(1、¡)。
1. 將光碟插入雷射唱機。
¶ 在飛梭轉盤依指定方向轉動的同時按下其中一個SEARCH鍵(1、¡)
本機為高速旋轉以提供高度的效能。因此,光碟的置入會需時幾秒鐘。
以進入飛快向前或飛快向後模式。
2. 若有啟動自動提示功能,則按下PLAY/PAUSE鍵(6)。
¶ 搜尋的速度會根據飛梭轉盤轉動時的速度而改變。
¶ 僅限定目前時間有在顯示窗中亮起時才可按下PLAY/PAUSE鍵。所示
¶ 在飛快搜尋期間,搜尋方向為取決於飛梭轉盤轉動的方向。所按SEARCH
音軌的開頭中的靜音部份會跳過,同時會立即從音軌的第一處條格
鍵(1、¡)的方向則可忽略不計。
開始播放。
¶ 當飛梭轉盤停止轉動,本機即會回到播放模式。
¶ 當飛梭模式設定為[VINYL],播放會慢慢加快至最大速度。(☞“欲
¶ 當放開SEARCH鍵(1、¡)後,飛快搜尋即取消。
暫停播放時”)
¶ 播放MP3時,向前快轉/向後快轉僅限用於同一資料夾中的音軌。
當音軌的播放結束時,即會提示下一音軌。提示指示燈(CUE鍵上的外
¶ 播放MP3時,向前快轉/向後快轉的次數可能會視音軌而有所減少。
圈)會亮起,而PLAY/PAUSE鍵上的外圈則會閃爍以指出本機已進入播放
待命模式。
當PLAY/PAUSE鍵(6)按下時,下一音軌即會開始播放。
若自動提示功能關閉,即會自動從第一首音軌開始播放。
¶ 當自動提示功能關閉,在第一首音軌已經播放後播放仍會繼續,並依
序播放以後所有的音軌。
54
ChH <DRB1398>
Before Operating (Names and Functions
DJ雷射唱機的操作
of Parts)
音軌搜尋 2. 搜尋提示點的確切位置。
¶ 使用音框數來指定提示點。
按下其中一個TRACK SEARCH鍵(4、¢)。 提示點能以1音框為單位來指定(其中75個音框等於1秒)。
¶ 每次按下此鍵,音軌搜尋即會依所按下相對按鍵上箭頭所指的方向操作 使用飛梭轉盤或向前或向後SEARCH按鍵(1、¡)來推音框數。轉
(在音軌的播放期間,要回到前面音軌的起點,請按兩次4鍵)。在 動飛梭轉盤一圈等於135個音框。按下SEARCH鍵時便可使雷射唱機依
MP3播放期間,將會依按下方向找到第一首音軌,同時搜尋也僅限於相 指定方向推進1個音框。
同資料夾的音軌。若資料夾的搜尋工作在插入CD-ROM時未能完成,則僅 ¶ 就目前音框聆聽聲音來決定提示點。
會針對根目錄中的音軌進行搜尋。 緩慢轉動飛梭轉盤並接著將其轉動至剛好在您想要開始播放的位置
¶ 當繼續按住此鍵,即會一直進行音軌搜尋。若繼續按住此鍵兩秒以上不 前。(因此定出的提出點將會包含在提示暫停期間仍可聽到聲音的一
放,即會增加搜尋的速度。 點。)
¶ 藉由在第一首音軌(音軌1)的起點按兩次4鍵,即會搜尋到最後一道 3. 在您到達指定的音框數或在您想要開始提示的一點上聽到聲音
音軌。在MP3播放期間,當在編號最小的音軌上按下4鍵,則會搜尋 時按下CUE鍵。
到同一資料夾中的最後一首音軌。 ¶ 聲音將會關掉且目前的時間將會出現在顯示窗中,表示該提示點己
¶ 藉由在最後一首音軌上按下¢鍵,即會搜尋到第一首音軌(音軌1)。 經存入記憶體中。
MP3播放期間,在最後一首音軌上按下¢鍵時,即會搜尋同一資料夾 ¶ 當提示點存入記憶體中,先前的設定將會刪除。
中編號最小的音軌。 [修改提示點]
1. 在播放期間,按下CUE鍵。
7 飛快音軌搜尋
¶ 雷射唱機將會回到指定的提示點。
轉動飛梭轉盤同時按下其中一個TRACK SEARCH按鍵(4、
2. 按下其中一個SEARCH按鍵(1、¡)以設定聲音暫停模式。
¢)。
3. 在CDJ模式下,要設定提示點,請依上述進入步驟2和3。
¶ 欲執行飛快音軌搜尋,按住按鍵同時依您所需方向轉動飛梭轉盤以執行
音軌搜尋;飛快音軌搜尋的執行與飛梭轉盤轉動的程度成正比。 7 在VINYL模式下設定提示點
¶ 在飛快音軌搜尋期間,搜尋的方向取決於飛梭轉盤轉動的方向。TRACK 1. 播放期間,當播放到指定的提示點,按住飛梭轉盤盤面,或按
SEARCH鍵按下的方向即可忽略不計。
下PLAY/PAUSE鍵(6)以暫停播放。
¶ 在放開TRACK SEARCH鍵時,飛快音軌搜尋即可取消。
2. 在繼續按下飛梭轉盤盤面的同時,轉動轉盤以回到剛好您想要
開始播放前的音點位置。
資料夾搜尋(僅限MP3) 3. 當聲音正好在指定的提示點上,按下CUE鍵同時按著飛梭轉盤的
資料夾搜尋功能為用來搜尋CD-ROM各層資料夾中的音軌。 盤面。
按下其中一個FOLDER SEARCH按鍵(|、\)。 ¶ 當目前時間出現在顯示窗中,即表示提示點記憶設定已完成。
¶ 每次按下FOLDER SEARCH鍵時,資料夾即會跳至指定的方向。根目錄會 ¶ 當新的提示點存入記憶體中,先前的設定將會刪除。
以資料夾編號[00]顯示,資料夾名稱為[ROOT]。 [修改提示點]
¶ 藉由按住其中一個FOLDER SEARCH鍵,即可一直搜尋資料夾。若按鍵按 1. 在播放期間,按下CUE鍵。
住兩秒以上不放,搜尋速度就會增加。 ¶ 雷射唱機將會回到指定的提示點。
¶ 當從最小編號的資料夾開始反向搜尋,即會搜尋最後一個資料夾。 2. 在VINYL模式下,要設定提示點,請依上述進入步驟2和3。
¶ 當從光碟上的最後一個資料夾開始向前搜尋,則會搜尋最小編號的資料 ¶ 現在可使用SEARCH按鍵(1、¡)以和CDJ模式相同的方式來修改
夾。 提示點。
¶ 沒有可播放音軌的資料夾(空資料夾)將會略過,並搜尋下一個資料夾。
7 即時提示
7 飛快資料夾搜尋 播放期間,在所需提示點上按下LOOP IN/REALTIME CUE鍵。
轉動飛梭轉盤的同時按下其中一個FOLDER SEARCH鍵(|、\)。 ¶ 此點將會接著做為新提示點錄製下來。
¶ 藉由依照指定的搜尋方向轉動飛梭轉盤同時按下其中一個F O L D E R
SEARCH鍵,即會搜尋飛梭轉盤轉動方向相對編號的資料夾。
7 檢查提示點(提示點取樣器)
¶ 在飛快搜尋期間,搜尋方向取決於飛梭轉盤轉動的方向。F O L D E R 在設定好提示點後,持續按著CUE鍵。
SEARCH鍵所指方向即可忽略不計。 ¶ 只要一直按著CUE鍵,就可聽到在設定提示點上的聲音。
¶ 當放開FOLDER SEARCH鍵,飛快資料夾搜尋即可取消。 ¶ 在提示點取樣期間,若將CUE鍵放開,將會從該設定提示點上執行返回
提示(back cue)操作。
¶ 播放MP3時,提示點取樣操作僅限在相同資料夾內。
提示點設定
在將提示點存入記憶體後,播放期間,藉由按下CUE鍵即可用來將雷射唱機 7 回到一提示點(返回提示)
置於準備從提示位置開始播放的狀態。 1. 在播放期間,按下CUE鍵。
¶ 雷射唱機將會回到指定的提示點。
7 在CDJ模式下設定提示點 2. 按下PLAY/PAUSE鍵(6)。
1. 播放期間,按下PLAY/PAUSE按鍵(6)以暫停播放在您想要開始 ¶ 播放將會立即從指定的提示點上開始。
播放的該點位置上。 ¶ 播放MP3時,提示點取樣操作僅限在相同資料夾內。只要該提示點一
直未被覆蓋,即使在資料夾搜尋後也仍能保存在記憶體中。
55
<DRB1398> ChH
DJ雷射唱機的操作
CUE
4. 旋轉播放(Spin play):播放或暫停期間轉動飛梭轉盤。
請參閱「進階操作」中的“旋轉播放(Spin Play)”。
PLAY/PAUSE 5. 高速搜尋:播放期間轉動飛梭轉盤,同時持續按住SEARCH鍵
6
要執行高速搜尋,按住SEARCH鍵(1、¡)並依所要搜尋方向轉動飛
飛梭轉盤 節拍調整滑桿 梭轉盤;高速搜尋會按相對於飛梭轉盤轉動的程度執行。
¶ 搜尋的速度會根據飛梭轉盤轉動時的速度而改變。
欲變更播放速度時 ¶ 搜尋會按飛梭轉盤轉動的方向執行,而與按下SEARCH鍵無關。
向前或向後移動節拍調整滑桿 ¶ 當轉盤轉動停止,播放即會恢復正常。
當移向使用者(+)時,播放速度(節拍)會變快,而移開(-)時,播放速度會 ¶ 當放開SEARCH鍵,此模式即取消。
變慢。 ¶ 播放MP3時,向前快轉/向後快轉僅限於同一資料夾內執行。
¶ 節拍改變的程度一切都會顯示在顯示窗中。 6. 高速音軌搜尋:轉動飛梭轉盤同時持續按住TRACK SEARCH鍵。
¶ 即使在改變節拍時,音高(音調)仍可保持平穩(請參閱以下的“應用主 欲執行高速音軌搜尋,按住TRACK SEARCH鍵(4、¢)的同時,依所
要節拍控制功能”乙節)。 需搜尋的方向轉動飛梭轉盤;高速搜尋會按相對於飛梭轉盤轉動的桯度
執行。
7 選擇節拍調整的範圍 ¶ 搜尋會按飛梭轉盤轉動的方向執行,而與按下的TRACK SEARCH鍵無
關。
按下TEMPO ±6/±10/±16/WIDE鍵。
¶ 當放開TRACK SEARCH鍵,此模式即取消。
每次按下此鍵,節拍調整滑桿的變動範圍就會依照±6 %/±10 %/±16 %/
¶ 播放MP3時,搜尋僅限於同一資料夾內執行。
WIDE的順序輪流改變。當選擇±6 %,則每次變動的單位是0.02 %;當選
擇±10 %,每次變動的單位是0.05 %;當選擇±16 %,每次變動的單位
7. 高速資料夾搜尋:轉動飛梭轉盤同時持續按住FOLDER SEARCH鍵
是0.05 %;而當選擇WIDE,每次變動的單位是0.5 %。 (MP3播放期間)。
¶ 節拍改變的程度一切都會顯示在顯示窗中。 欲執行高速資料夾搜尋,按住FOLDER SEARCH鍵(|、\)同時,依所需
¶ WIDE設定的變動範圍如下: 搜尋的方向轉動飛梭轉盤;高速資料夾搜尋會按相對於飛梭轉盤轉動的
CD播放時: ±100 % 程度執行。
MP3播放時: +70 % 至 -100 % ¶ 搜尋會按飛梭轉盤轉動的方向執行,而與按下的FOLDER SEARCH鍵
¶ 在初次將電源打開時,設定預設值為±10 %。 無關。
¶ 在-100 %時,播放會停止。 ¶ 當放開FOLDER SEARCH鍵,此模式即取消。
7 節拍重新設定 備註:
在飛梭轉盤的盤面上裝有一內建開關;切勿在轉盤上置放任何物品或
按下TEMPO RESET鍵。
施加重力。切勿將飲料置於盤面上,以免液體濺入機件內部而導致故
節拍重設指示燈會亮起,同時節拍變動率會變為“0”(正常節拍),不論節
障。
拍調整滑桿當時的位置為何。
¶ 若再按一次TEMPO RESET鍵,重設即會取消(節拍變動率會回復到節拍
調整滑桿所設定的位置)。
¶ 在初次將電源打開時,本項功能是預設為OFF。 飛梭靈敏度調整
藉由旋轉JOG ADJUST旋鈕,便能調整飛梭轉盤於轉動時所感受阻力的靈敏
應用主要節拍控制功能 度。
播放期間,按下MASTER TEMPO鍵。
轉動JOG ADJUST旋鈕
MASTER TEMPO鍵及[MT]指示燈亮起。速度(節拍)現在已可應用節拍調整滑
¶ 當順時針轉動,阻力會增加。
桿來變更,不過音高(音調)則保持不變。
¶ 當逆時針轉動,阻力會減少。
¶ 在做數位化處理時,音質可能會有所降低。
¶ 調整在刻盤灰區內的設定以將飛梭轉盤的靈敏度設定為同等於C D J -
¶ 在初次將電源打開時,本項功能是預設為OFF。
1000MK2。
(當飛梭模式設定為[VINYL],觸控範圍便僅限於飛梭轉盤的兩邊。若是
觸控上方盤面,則會執行不同的功能。)
56
ChH <DRB1398>
Before Operating (Names and Functions
DJ雷射唱機的操作
of Parts)
混合不同音軌 關於WAVE音階顯示
(例:將音軌B與目前播放自主要揚聲器的音軌A混合) WAVE音階顯示窗可顯示一音軌在低音節奏(低音鼓等)中的變化,使DJ能清
¶ 連接雷射唱機CD1至DJ混音器的CH1,另連接雷射唱機CD2至CH2。 楚了解音軌中斷和結束的位置。當將TEXT MODE按鍵設定為WAVE播放,則
¶ 適當調高TRIM(修飾)、CHANNEL FADER(聲道淡入淡出)及MASTER LEVEL 所選音軌會放大顯示以填滿整個顯示窗的範圍(100點)。
(主音量)設定值,使聲音能產生自CD1。 ¶ 在切換音軌後,需一些時間整首音軌的WAVE顯示圖形才會顯示。藉由預
1. 將D J 混音器的C R O S S F A D E R (交替淡化器) 滑桿撥至其左側 先將所需音軌的WAVE圖形錄到記憶卡上,下次播放音軌時,其WAVE圖形
(CH1)。 便可立即顯示(☞第61頁)
¶ 自揚聲器聽到音軌A。 ¶ 若音軌的低頻節奏變化的音量太低,則音軌中的中斷點便可能無法正確
2. 將CD置入雷射唱機CD2內。 顯示。
3. 按下雷射唱機CD2上的TRACK SEARCH鍵(4、¢)以搜尋並選 ¶ 若在讀取音階波形期間執行搜尋或暫停操作,則波形便可能會無法正確
顯示。
擇音軌B。
¶ 在MP3播放期間是無法事先讀取(read-ahead)WAVE圖形的。
4. 將DJ混音器的MONITOR SELECTOR按鍵CH2設定至ON。
5. 轉動DJ混音器的MONITOR LEVEL,使能從耳機中聽到音軌B。
¶ 自揚聲器僅能聽到音軌A。 關於TEXT文字顯示
6. 設定耳機上音軌B的提示。 當使用TEXT MODE按鍵來選取TEXT文字顯示時,顯示窗中即會顯示CD-
1 在雷射唱機CD2在播放模式之下,按下PLAY/PAUSE鍵(6)以能聽到 TEXT,包含音軌、專輯、及演出者的名稱。MP3播放期間,螢幕會顯示ID3
您想要提示的一點。 tag音軌名稱(若未錄有ID3 tag,則螢幕會顯示檔案名稱)/ID3 tag專輯名
¶ 當飛梭模式設定為[C D J ] ,本機將會進入聲音暫停( a u d i b l e 稱/ID3 tag演出者名稱。
pause)模式(可聽到聲音);當設定為[VINYL],本機將會進入靜 ¶ 每一項目可顯示多達48個字元的文字;文字長度超出16個字的部份須捲
音暫停(inaudible pause)(不會聽到任何聲音)。 動顯示。
2 轉動雷射唱機CD2的飛梭轉盤並搜尋音軌的提示點(第一拍)。 ¶ 文字中可能包含文數字及一些符號。
3 當您完成提示點的設定後,按下雷射唱機CD2上的CUE鍵。 ¶ 若沒有文字,則會顯示[NO TEXT]訊息。
¶ 雷射唱機的聲音將會關掉,同時提示完成。
7. 在從揚聲器中聽到音軌A 的同時,按下雷射唱機CD2的PLAY/ 當一音軌名稱選擇以TEXT方式顯示,則在音軌名稱後面即會跟著顯示[ ]
PAUSE鍵(6)。 圖示(播放MP3時,將會顯示ID3 tag的標題名稱或檔案名稱)。
¶ 從主要揚聲器中僅會聽到音軌A。 另外,在MP3播放期間,位元率會顯示在音軌名稱之後。
¶ 音軌B將會從耳機中聽到。
8. 移動節拍調整滑桿以求能配合音軌A及B的節拍(BPM=每分鐘節拍
數)。
移動CD2的節拍調整滑桿,使音軌B的BPM能配合音軌A的BPM。 當一專輯名稱選擇以TEXT方式顯示,則在專輯名稱的後面即會跟著顯示
¶ 當兩BPM率彼此匹配,BPM同步便告完成。 [ ]圖示。
9. 按下雷射唱機CD2上的CUE鍵。
Pioneer
¶ 雷射唱機CD2將會在該提示點上進入暫停模式。
10.在從揚聲器中聽音軌A的同時,按下雷射唱機CD2上的PLAY/
當一演出者名稱選擇TEXT方式顯示,則在演出者名稱後面即會跟著顯示
PAUSE鍵(6)。
[ ]圖示。
¶ 音軌B開始播放。
11.在確認耳機上聲音的同時,將DJ混音器的CROSS FADER從左向
Pioneer PRO DJ
右逐漸移動(CH2)。
¶ 來自揚聲器音軌A的聲音將會逐漸穩穩地溶合音軌B的聲音。 對MP3執行資料夾搜尋時,則在搜尋期間會顯示資料夾名稱。
¶ 當DJ混音器的CROSS FADER完全移至右邊,從揚聲器中聽到的聲音
將會從音軌A切換到音軌B,同時操作完成。 Pioneer DJ
7 長時間混音播放
只要BPM率匹配,若是將CROSS FADER置於中間位置,音軌A與B的混音就會
均勻中聽。
7 淡化器啟動(Fader start)播放
使用Pioneer DJ混音器的交替淡化器啟動功能,即會跳過上述步驟10以產
生均勻的取樣混音效果。此外,當CROSS FADER滑桿回到其原來位置,即
會回到步驟9中的狀態(雷射唱機CD2在其提示點上),使您得以重複相同的
播放,多少次都行。
57
<DRB1398> ChH
進階操作
進階操作
LOOP IN/REALTIME LOOP OUT 旋轉播放(Spin Play)
CUE (IN ADJUST) (OUT ADJUST) RELOOP/EXIT VINYL
SPEED 在VINYL模式的播放期間,按下飛梭轉盤的盤面或按下PLAY/PAUSE鍵(6)
ADJUST
HOT CUE A TOUCH 以暫停播放,接著快速轉動飛梭轉盤;即使您將飛梭轉盤上的手放開,播
/BRAKE 放也會按相對於飛梭轉盤轉動的方向和速度進行。
HOT CUE B
HOT CUE C VINYL
SPEED
HOT CUE
REC MODE
ADJUST 煞速(Braking)
RELEASE
/START ¶ 在VINYL模式的播放期間,若是按下PLAY/PAUSE鍵(6)暫停播放,則
DIRECTION
FWD/REV 聲音就會根據VINYL SPEED ADJUST TOUCH/BRAKE旋鈕所設定的煞速減
JOG
MODE 緩下來。
SELECT
¶ 當再按下PLAY/PAUSE鍵(6)恢復播放,聲音就會根據VINYL SPEED
SEARCH ADJUST RELEASE/START旋鈕所設定的速度加快。
1, ¡
CUE 循環播放
PLAY/PAUSE 7 設定循環
6
1. 按下PLAY/PAUSE鍵(6)以開始播放。
飛梭轉盤
2. 播放或暫停期間,按下LOOP IN/REALTIME CUE鍵。
¶ 此項操作若是事先錄下的提示點已有設定循環起始點時即無此需
刮片播放(Scratch Play) 要。
當將飛梭模式設定為[VINYL],按住飛梭轉盤的上方盤面並轉動,可使播放 3. 當播放到指定的退出循環(loop-out)點時,按下LOOP OUT鍵。
按相對於飛梭轉盤轉動的速度和方向比例進行。 ¶ 播放會在進入循環(loop-in)與退出循環(loop-out)點之間開始。
1. 按下JOG MODE SELECT鍵使[VINYL]指示燈亮起。 ¶ MP3播放期間,循環僅能設定在同一音軌內所設定的各點之間。
2. 播放期間,按下飛梭轉盤的上方盤面。 ¶ 在循環已設定好後,RELOOP/EXIT按鍵會亮起。
¶ 播放便慢下來並停止(到完全停止[“反應特性”]的減緩時間可分開
設定)。若在播放速度減緩至完全停止之前,即轉動飛梭轉盤,聲音 7 取消循環時
便會停止。後續,播放將會按步驟3中飛梭轉盤轉動的方向和速度進 在循環播放期間,按下RELOOP/EXIT鍵。
行。 ¶ 當播放到退出循環(loop-out)點時,仍會正常地繼續播放,而不會回到
3. 按您想要執行播放的方向及速度轉動飛梭轉盤。 進入循環(loop-in)點。
¶ 將會按飛梭轉盤轉動的方向和速度聽到播放的聲音。
4. 將手從飛梭轉盤上移開。 7 變更進入循環(loop-in)點時
¶ 播放將會加快或減緩回到其觸控飛梭轉盤之前的狀態。(到播放回到
1. 在循環播放期間,按下LOOP IN/REALTIME CUE (IN ADJUST)
其原先狀態[“反應特性”]的加快或減緩時間可分開設定)。
鍵。
7 如何設定減緩反應特性(按下飛梭轉盤盤面時播放減緩
¶ 顯示窗會顯示進入點(in-point)時間;LOOP IN/REALTIME CUE按鍵
到完全停止所需時間): 將切換成快速閃爍的狀態,而LOOP OUT指示燈將會熄滅。
轉動VINYL SPEED ADJUST TOUCH/BRAKE旋鈕。 2. 按下SEARCH鍵(1, ¡)或轉動飛梭轉盤。
¶ 此旋鈕能讓您調整減緩的速度(反應特性)到播放完全停止。 ¶ 進入循環(loop-in)點會以每1音框的間隔改變。進入點的調整許可
¶ 這與在VINYL模式下按下PLAY/PAUSE鍵(6)以暫時暫停播放所用的減 範圍為±30音框,且此值須在設定任何退出點前完成設定。
速調整是一樣的設定值。(☞第54頁) ¶ 當播放MP3時,循環位置僅能在提示點所設定的同一音軌之中進行調
整。
7 如何設定加快反應特性(播放回到手從飛梭轉盤盤面離 ¶ 進入循環(loop-in)點在返向播放及刮片播放期間無法修改。
開時之速度所需時間): ¶ 當按下LOOP IN/REALTIME CUE鍵或已播放30秒後,調整模式即會取
消同時恢復循環播放。
轉動VINYL SPEED ADJUST RELEASE/START旋鈕。
¶ 此旋鈕能讓您調整減緩或增加的速度,到播放回到正常播放為止(反應
特性)。 7 變更退出循環(loop-out)點時
¶ 這與在VINYL模式下按下PLAY/PAUSE鍵(6)以暫時暫停播放所用的加 1. 循環播放期間,按下LOOP OUT (OUT ADJUST)鍵。
速調整是一樣的設定值。(☞第54頁) ¶ 顯示窗會顯示退出點(out-point)時間;LOOP OUT按鍵將切換成快
速閃爍的狀態,而LOOP IN/REALTIME CUE指示燈將會熄滅。
2. 按下SEARCH鍵(1, ¡)或轉動飛梭轉盤。
¶ 退出循環(loop-out)點會以每1音框的間隔改變。
¶ 退出循環(loop-out)點無法移動至進入循環(loop-in)點之前的位
置。
¶ 當播放MP3時,循環位置僅能在提示點所設定的同一音軌之中進行調
整。
¶ 退出循環(loop-out)點在返向播放及刮片播放期間無法修改。
¶ 當按下LOOP OUT鍵或已播放30秒後,調整模式即會取消同時恢復循
環播放。
58
ChH <DRB1398>
Before Operating (Names and Functions of進階操作
Parts)
反向播放
將DIRECTION FWD/REV開關設定在[REV]位置。
[REV]指示燈亮起,並開始從相反方向播放。
¶ 利用飛梭轉盤所製造的播放加速/減速效果將會以相反方向操作。
¶ 在反向播放期間,可建立新的循環或編輯退出循環(loop-out)點。
¶ 若已執行音軌搜尋或循環播放,記憶卡狀態指示燈(飛梭轉盤顯示)將會
閃爍1至2秒,且刮片/反向操作可能會暫時失去作用。
¶ 當播放MP3時,多重疊個資料夾的情況下無法進行反向播放。
¶ 在MP3播放期間,有些音軌無法立即進行反向播放。
59
<DRB1398> ChH
使用記憶卡操作
使用記憶卡操作
■ 使用記憶卡
本台雷射唱機可使用SD記憶卡或MultiMedia Cards(MMC)來錄製光碟識別
備註:
資料、提示點資料、循環點資料,以及熱提示資料。 ¶ CARD指示燈閃亮時切勿打開蓋板或關閉電源,以免造成錄製資料
損壞。
★ SD記憶卡須依照“SD Memory Card Specifications Part2 FILE SYSTEM ¶ 記憶卡是種精密的電子化裝置。切勿折到或摔到,或受到重力、
SPECIFICATION Version 1.0”的標準格式化(一般市售的SD記憶卡 撞擊。另外,避免在會受到靜電或電氣雜訊的環境中使用或進行
於原廠即已按照上述標準完成格式化)。未經格式化的記憶卡無法使 儲存。
用(螢幕上會顯示 [UNFORMAT] 訊息)。 ¶ 若是受到撞擊或靜電,則可能會因此損壞。手拿記憶卡時請特別
★ 在電腦或數位相機上格式化的記憶卡無法用於本台播放器上。 小心,並定期備份所錄製的重要資料(☞第61頁)
Pioneer對於因這類疏失致使記憶卡資料有所損壞或遺失,或造成其
他意外的損壞,概不負責。
★ 在CDJ-1000或CDJ-1000MK2上格式化的MultiMedia Cards(MMC)有
以下限制:
¶ MP3資料無法錄製。
¶ 以熱提示方式設定的循環資料不能錄製。 CUE/LOOP
MEMORY
¶ 您無法使用電腦來複製或備份記憶卡。
¶ 在錄製循環點時,單一循環點需有兩處記憶區。 CUE/LOOP
DELETE
¶ 記憶卡無法在本機上重新格式化。
CUE/LOOP
CALL
2, 3
欲保護重要資料時(SD記憶卡)
防寫開關
背面
¶ 將防寫開關設定在[LOCK]位置以防進一步寫入記憶卡。若您想要錄
製另外的資料到記憶卡上,請將開關設回其原來位置。
錄到記憶卡上
¶ 每張光碟最多可錄上100點(提示點和循環點兩者加總)。當已儲存到100
點,若嘗試要再多錄點數,將會顯示[POINT FULL]的訊息。
■ 裝入記憶卡 ¶ 若記憶卡上的記憶空間已不足以錄製目前的點數,即會出現[ C A R D
FULL]的訊息。
記憶卡指示燈 ¶ 若記憶卡已設定為防寫,即會顯示[CARD PROTECTED]的訊息。
(CARD)
■ 錄製提示點
1. 使用自動提示功能或CUE鍵來輸入提示點。
2. 按下CUE/LOOP MEMORY鍵。
標籤面朝上 ¶ 螢幕上會顯示提示點位置資料,並顯示[CARD MEMORY],以指出該
提示點已存入記憶卡中。
¶ 若無插入記憶卡,即會出現[NO CARD]的訊息。
記憶卡 ¶ 若在未插有記憶卡的情況下打開記憶卡蓋,則螢幕上會顯示[CLOSE
CARD DOOR]。
記憶卡蓋
■ 錄製循環點
打開記憶卡蓋,並插入記憶卡,插入時標籤面朝上且切緣朝前。請水平拿 1. 設定一進入循環(loop-in)點及退出循環(loop-out)點並開始循
穩將其緩緩插入,並往內壓直至無法前進為止。關上記憶卡蓋。 環播放。
顯示窗會顯示[SD CARD](以示記憶卡符合SD記憶卡標準)或[CDJ CARD](以 2. 在循環播放期間,按下CUE/LOOP MEMORY鍵。
示記憶卡為利用CDJ-1000或CDJ-1000MK2格式化),隨後並顯示錄在記憶卡 ¶ 螢幕上會顯示提示點位置資料,並顯示[CARD MEMORY],以指出進
的光碟編號。 入循環和退出循環點已存入記憶卡中。
¶ 若無插入記憶卡,即會出現[NO CARD]的訊息。
¶ 取出記憶卡。 ¶ 若在未插有記憶卡的情況下打開記憶卡蓋,則螢幕上會顯示[CLOSE
打開記憶卡蓋並等到,CARD指示燈熄滅,然後輕按記憶卡,讓其得以退 CARD DOOR]。
出;抓住記憶卡末端,小心將其抽出。
■ 錄製熱提示點A、B、C
熱提示點A、B、C均會自動錄到記憶卡上。
■ WAVE音階顯示
WAVE音階顯示會自動錄到SD記憶卡上。
60
ChH <DRB1398>
Before Operating (Names and Functions
使用記憶卡操作
of Parts)
欲叫出所錄資料 欲複製記憶卡上資料
■ 叫出記憶提示/循環點時 1. 在光碟或記憶卡插入的情況下:
當記憶卡插入,並錄有CUE/LOOP點資料,日曆顯示窗及播放位址顯示窗便 按住CUE/LOOP MEMORY鍵5秒鐘以上不放。
會呈現紅色。 ¶ 顯示窗會顯示[COPY MODE][CARD A IN]訊息。
1. 按下CUE/LOOP CALL鍵。 2. 將原始來源記憶卡插入記憶卡槽。
¶ 當按下CALL鍵(3),便可叫出CUE/LOOP點以便能從最為接近光碟開 ¶ 顯示窗會顯示[READING]訊息;幾分鐘後,將會出現[CARD B IN]訊
頭的位置開始播放,同時本機會暫停在該CUE/LOOP點。 息。
2. 按下PLAY/PAUSE鍵(6)。 3. 取出來源記憶卡並插入目標記憶卡。
¶ 播放/循環播放開始。 ¶ 請確實將目標記憶卡上早先的資料刪除以提供足夠的錄製容量。
■ 叫出記憶熱提示點 ¶ 顯示窗會顯示[WRITING]訊息,幾分鐘後,將會出現[CARD A IN]訊
息。
熱提示點會自動錄到記憶卡上。若熱提示點是在光碟插入時錄下,則HOT
CUE鍵A、B、C將會閃爍綠或橘燈。欲叫出其中一個錄製的熱提示點,按下 4. 取出目標卡,並再次將來源卡插入。
相關的A、B或C鍵。閃爍中綠或橘燈呈穩定亮起(完成叫出時並不會立即開 ¶ 顯示窗會顯示[READING]訊息;幾分鐘後,將會出現[CARD B IN]訊
始就有聲音)。若您不需叫出其中的熱提示點,請按下HOT CUE REC MODE 息。
鍵。指示燈會轉為紅色,同時啟用熱提示設定模式。(欲接連叫出先前錄在 5. 依需要重複步驟3及4。
記憶卡上的任一提示點,請將光碟或記憶卡取出,然後再插回去,使A、B ¶ 當顯示窗會顯示[COMPLETE]訊息即表示複製過程已完成。
或C鍵再一次閃爍。接著按下所需的閃爍中按鍵)。 ¶ 複製一張32 MB的SD記憶卡需執行錄製步驟3至4最多4次。
¶ 當目標卡的記憶容量不足以完成複製過程時,將會出現[CAPACITY
■ WAVE音階顯示 ERROR]訊息。
在播放您先前已有使用WAVE音階顯示功能的音軌時,所錄的WAVE圖形將會
¶ 若您擁有的電腦內建有讀卡機/燒錄機,則可使用讀卡機/燒錄機複製您
自動地錄下並顯示。
的SD記憶卡。(在CDJ-1000或CDJ-1000MK2上格式化的MultiMedia
欲刪除錄在記憶卡上的資訊時 Cards,不能利用電腦進行複製)
☞第60頁與記憶卡格式化有關的注意事項。
■ 刪除各提示/循環點時
1. 按下CUE/LOOP CALL鍵。 提示及循環點錄製期間的顯示
¶ 當按下CALL鍵(3),便可叫出CUE/LOOP點以便能從最為接近光碟開
頭的位置開始播放,同時本機會暫停在該CUE/LOOP點。 顯示訊息 意義說明
2. 在您想要刪除的提示/循環點上按下CUE/LOOP DELETE鍵。 [CARD MEMORY] 提示點或循環點已成功存入記憶卡。
¶ 顯示窗會顯示[DELETE]訊息,同時所選取的提示點或循環點資料將
[CANNOT MEMORIZE ON 在MP3播放期間,當CDJ-1000或CDJ-
會自記憶卡中刪除。
THIS CARD] 1000MK2所格式化的記憶卡已插入並已執行
錄製操作時會顯示。提示/循環點資料不會
■ 刪除整張光碟上的所有提示/循環點資訊時 錄到記憶卡上。
1. 插入您想要將提示/循環點資訊刪除的光碟。
[CARD FULL] 記憶卡上的空間容量仍然不足。提示/循環
2. 按住CUE/LOOP DELETE鍵5秒鐘以上不放。
點資料不會錄到記憶卡上。
¶ 顯示窗會顯示[DISC DELETE? PUSH MEMORY]確認訊息。
3. 按下CUE/LOOP MEMORY鍵。 [CARD PROTECTED] 記憶卡的LOCK(防寫)功能啟用,使提示/循
¶ 所插入光碟的全部提示及循環資料將會從記憶卡上刪除。. 環點資料無法寫到記憶卡上。
¶ 若是按下CUE/LOOP MEMORY以外的按鍵,刪除模式即會取消。 [INTERNAL MEMORY],隨 沒有任何記憶卡插入。
後接著[NO CARD]
■ 刪除所記有記憶卡資料時 [INTERNAL MEMORY],隨 記憶卡插入,但記憶卡蓋未關上。將蓋關
1. 在無光碟插入的情況下,按住CUE/LOOP DELETE鍵5秒鐘以上不 後接著[CLOSE CARD 上重試。
放。 DOOR]
¶ 顯示窗會顯示[ALL DELETE? PUSH MEMORY]確認訊息。
[UNFORMAT] 插入的記憶卡不符SD記憶卡標準,或CDJ-
2. 按下CUE/LOOP MEMORY鍵。 1000、CDJ-1000MK2(MMC)格式化標準。提
¶ 所有資料將會自記憶卡上刪除。 示/循環點資料不會錄到記憶卡上。
¶ 若按下CUE/LOOP MEMORY以外的按鍵,刪除模式即會取消。
[CARD ERROR] 插入的記憶卡有損壞的跡象。
在錄製提示點資料、循環點資料、熱提示資料或WAVE音階資料時將記憶卡
插入。若無記憶卡插入,提示/循環點資料將會因電源關掉或目前光碟已取
出而遺失。
61
<DRB1398> ChH
故障排除
故障排除
不當之操作情形經常被誤以為是異常或故障。若您確信本機操作不當,請參照下表逐項檢查。有時不當之操作情形可能是源自於其他設備的異常或故障。
若問題未能獲得解決,則請逐一檢查其他搭配本台雷射唱機使用的設備。若問題仍在,請您就近洽Pioneer授權服務中心或經銷商有關維修事宜。
癥狀 可能原因 解決方法
即使按下EJECT鍵(0)亦無法將光碟 ¶ 電源插頭從插座上脫離。 ¶ 將插頭接到牆上插座。
退出 ¶ EJECT UNLOCK/LOCK設定在[LOCK]位置。 ¶ 在按下EJECT鍵(0)前,先進入暫停模式或提示
待命模式。
¶ 在按EJECT鍵(0)前,先將EJECT UNLOCK/LOCK鍵
設定在[UNLOCK]的位置。
62
ChH <DRB1398>
故障排除 (錯誤訊息顯示)
¶ 本設備在受到靜電干擾或其他外力影響時,可能會無法正確操作。此時,可嘗試關閉電源,並在光碟完全停止時再將電源打開。
¶ 本機無法播放局部錄製、未做終結的CD-R或CD-RW光碟。
¶ 本機僅可播放標準12公分光碟或裝於正確光碟轉換器上的8公分光碟;其無法播放形狀不規則的光碟(可能會發生損壞或故障)。
¶ 播放裝於轉換器上的8公分光碟時,在使用刮片及反向播放操作時可能會感到速度有些損失。本機在光碟高速旋轉時可提供高度的效
能,但當8公分光碟裝在轉換器上,轉速便會稍減以策安全。這不是故障。
¶ 本機所測之BPM值可能會與CD標籤上所標示之數值,或與Pioneer DJ混音器所測會有所出入。這是因BPM測量方法所造成的差異,這並
非故障。
¶ 在播放CD-R/RW光碟時,可能會出現某種程度上的效能降低,須視每張光碟的錄製品質而定。
錯誤訊息顯示
當本機無法正確操作,會有一錯誤代碼出現在顯示面板上。請將顯示的錯誤代碼與下表核對,以採取適當的作法修正錯誤。若顯示的是
下表所列以外的錯誤代碼,或若是已採取適當修正作法後仍顯示相同的錯誤代碼,請您就近洽Pioneer服務站或與您購買播放器的商家聯
絡,以取得協助。
日本先鋒公司出版
版權©2005日本先鋒公司
版權所有
63
<DRB1398> ChH
Supply of this product only conveys a license for private, non-com-
mercial use and does not convey a license nor imply any right to
use this product in any commercial (i.e. revenue-generating) real
time broadcasting (terrestrial, satellite, cable and/or any other me-
dia), broadcasting/streaming via internet, intranets and/or other
networks or in other electronic content distribution systems, such
as pay-audio or audio-on-demand applications. An independent
license for such use is required. For details, please visit
http://www.mp3licensing.com. MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson multimedia.
本產品的供應只能讓與在個人、非商業用途使用的許可,而不讓
與或意味在任意的商業性(即發生收益的)實時廣播(地面、衛
星、電纜及/或任何其他媒體),經由互聯網、企業網絡的廣
播/流及/或其他網絡或在其他電子內容分布系統,如付費音頻
或音頻點播等用途使用本產品的任何權利。對於這些用途,應需
要單獨的許可。有關詳情,請訪問
http://www.mp3licensing.com MPEG Layer-3音頻編碼技術經Fraunhofer IIS和Thomason mul-
timedia公司授權使用。