You are on page 1of 2

Q.No.

1 [5+5]
a) Finding the performance parameter of a three-phase Full wave controller for given below
question.The three-phase full wave controller in Fig.1 .Supplies a Y-connected resistive load of
𝝅
R=10 Ω and the line-to line input voltage is 208V(rms) 60Hz . Thedelay in 𝜶 = 𝟑 Determine (a) the rms
output phase voltage 𝑽𝒂𝒏 (b) the input PF and (c) The expression for the instantaneous output voltage
of phase a.

b) A DC regulator is operated at duty cycle of k = 0.40. The load resistance is 𝒓𝒄 = 150Ω. The inductor
is 𝒓𝒄 = 𝟎. 𝟐𝛀. Determine the voltage gain for the (a) Buck converter (b) - Boost converter and (c) Buck-
boost converter.

Q.No.2 [3+7]
a) Draw the voltage wave form of given 3phase system.

𝟐𝟓 + 𝟐𝟓 𝐜𝐨𝐬(𝝎𝒕 − 𝟗𝟎)
Vi = 𝟐𝟓 + 𝟐𝟓 𝐜𝐨𝐬(𝝎𝒕 + 𝟏𝟓𝟎)
𝟐𝟓 + 𝟐𝟓 𝐜𝐨𝐬(𝝎𝒕 + 𝟑𝟎)

b) Center tap transformer is applied 50𝑉𝐴𝐶 with turn ratio 1:2, for full-wave rectification system having
load resistance 𝟏𝟎𝟎 𝛀 .Find
a) The average load voltage
b) The maximum load current.
c) The average load current.
d) RMS value of load current
e) PIV rating for diode
f) Average power delivered to load
g) AC input power and Rectifier efficiency.

Q.No.3 [10]
Find the output voltage and current of a Three-phase Full-bridge inverter with RL load when a three-
phase inverter shown in Fig.2 has y-connecter load of R=5Ω and l=23mH. The inverter frequency is
𝑓𝑜 = 60𝐻𝑧 and the DC input voltage is 𝑉𝑠 = 220𝑣 find
a) Express the instaneous line-to-line voltage 𝑉𝑎𝑏 (𝑡) and line current 𝐼𝑎 (𝑡) in a fouriour
series.determine
b) the rms line voltage 𝑉𝐿 :
c) the rms phase voltage 𝑉𝑝
d) the rms line voltage 𝑉𝐿1 at

Fig.2

Q.No.4 [3+2+1+2+2]
Analysis and design of a buck-boost converter: A buck-boost converter is illustrated in Fig. (a), and a
practical implementation using a transistor and diode is shown in Fig. (b).

Fig a. Fig b.
A. Find the dependence of the equilibrium output voltage V and inductor current on the duty
ratio input voltage and load resistance R. You may assume that the inductor current
ripple and capacitor voltage ripple are small.
B. Plot your results of part (a) over the range 0≤𝑫≤𝟏
C. DC design: for the specifications
𝑉𝑅 = 30𝑣 𝑉 = −20𝑣
𝑅 = 4Ω 𝑓𝑠 = 2khz
i.
Find duty ratio D and inductor current /.
ii. Calculate the value of L that will make the peak inductor current ripple ∆𝑖 equal to
ten percent of the average inductor current I.
iii. Choose C such that the peak output voltage ripple∆𝑣 is 0.1 V.

You might also like