You are on page 1of 11

Add Intra-Frequency Neighboring Cell(ADD UINTRAFREQNCELL)

Function

Use this command to add an intra-frequency neighboring cell.


Note

1. Based on the usage scenario, two intra-frequency neighboring cells can be configured as bidirectional
or unidirectional neighboring cells. Assume that cell1 is configured as an intra-frequency neighboring cell
of cell2.
- If cell2 is also configured as an intra-frequency neighboring cell of cell1, cell1 and cell2 are bidirectional
neighboring cells.
- If cell2 is not configured as an intra-frequency neighboring cell of cell1, cell1 is a unidirectional
neighboring cell of cell2.
2. A maximum of 63 intra-frequency neighboring cells can be configured for a cell if
PERFENH_INTRAFREQ_NCELL_MAX_NUM_SWITCH of the PERFENHANCESWITCH4parameter in
the SET UCORRMPARA command is set to 0. As specified in 3GPP protocols, a maximum of 32
intra-frequency cells can be measured.
A maximum of 31 intra-frequency neighboring cells can be configured for a cell if
PERFENH_INTRAFREQ_NCELL_MAX_NUM_SWITCH of the PERFENHANCESWITCH4parameter in
the SET UCORRMPARA command is set to 1.
3. Before adding an intra-frequency neighboring cell, check whether this cell belongs to the local RNC or
another RNC. If the cell belongs to another RNC, run the ADD UEXT3GCELL command to add the
information of this cell first.
4. For a single host cell or primary host cell, the RNC ID is the ID of the serving RNC; for a secondary
host cell, the RNC ID is the ID of the RNC that controls the corresponding primary host cell. (Dual-homed
cell refers to the cell that has a peer cell in a RNC pool in the node redundancy function. Single-homed
cell refers to the cell that does not have a peer cell in a RNC pool in the node redundancy function. Both
primary cell and secondary cell are dual-homed cell. For details on the cell configuration, see the
parameter description of ADD UCELLSETUP.)
5. For a dual-homed cell, only the primary cell can be configured with neighboring cells. The secondary
cell cannot be configured with neighboring cells.
6.A cell can be configured as a neighboring cell of a maximum of 256 cells. This restriction is not
applicable to AP cells.
7.The RNC can be configured with a maximum of 163200 intra-frequency neighbor relationships.
Parameters

Parameter ID Parameter Name Parameter Desc

RNCId RNC ID Meaning: ID of an RNC


GUI Value Range: 0~4095
Unit: None
Actual Value Range: 0~4095
MML Default Value: None
Parameter ID Parameter Name Parameter Desc

Recommended Value: None


Parameter Relationship:
-Configuration constraints:
If the RNC ID specified by [UINTRAFREQNCELL:RNCId] an
[UINTRAFREQNCELL:NCellRncId] are different, [UINTRAF
to TRUE.
If the RNC ID specified by [UINTRAFREQNCELL:RNCId] an
[UINTRAFREQNCELL:NCellRncId] are different, [UINTRAF
toTRUE.
When adding a [UINTRAFREQNCELL], records that have the
[UINTRAFREQNCELL:CellId] in [UINTRAFREQNCELL] an
[UINTERFREQNCELL:RncId] and [UINTERFREQNCELL:Ce
following conditions: The total number of records whose [UINT
the same as [UINTRAFREQNCELL:NCellRncId] is 10.
Service Interrupted After Modification: N/A
Impact on Network Performance: None
CellId Cell ID Meaning: Unique ID of a cell
GUI Value Range: 0~65535
Unit: None
Actual Value Range: 0~65535
MML Default Value: None
Recommended Value: None
Parameter Relationship:
-Configuration constraints:
When adding a [UINTRAFREQNCELL], if PERFENH_INTRA
[UCORRMPARA:PerfEnhanceSwitch4] is set to 0, [UINTRAFR
whose [UINTRAFREQNCELL] and [UINTRAFREQNCELL:C
When adding a [UINTRAFREQNCELL], if PERFENH_INTRA
[UCORRMPARA:PerfEnhanceSwitch4] is set to 1, [UINTRAFR
whose [UINTRAFREQNCELL] and [UINTRAFREQNCELL:C
When adding a [UINTRAFREQNCELL], records that have the
[UINTRAFREQNCELL:CellId] in [UINTRAFREQNCELL] an
[UINTERFREQNCELL:RncId] and [UINTERFREQNCELL:Ce
following conditions: The total number of records whose [UINT
the same as [UINTRAFREQNCELL:NCellRncId] is 10.
Service Interrupted After Modification: N/A
Impact on Network Performance: None
Parameter ID Parameter Name Parameter Desc

NCellRncId RNC ID of a Meaning: Unique RNC ID of a neighboring cell


neighboring cell GUI Value Range: 0~4095
Unit: None
Actual Value Range: 0~4095
MML Default Value: None
Recommended Value: None
Parameter Relationship:
-Configuration constraints:
If the RNC ID specified by [UINTRAFREQNCELL:RNCId] an
[UINTRAFREQNCELL:NCellRncId] are different, [UINTRAF
to TRUE.
If the RNC ID specified by [UINTRAFREQNCELL:RNCId] an
[UINTRAFREQNCELL:NCellRncId] are different, [UINTRAF
toTRUE.
When adding a [UINTRAFREQNCELL], records that have the
[UINTRAFREQNCELL:CellId] in [UINTRAFREQNCELL] an
[UINTERFREQNCELL:RncId] and [UINTERFREQNCELL:Ce
following conditions: The total number of records whose [UINT
the same as [UINTRAFREQNCELL:NCellRncId] is 10.
When adding a [UINTRAFREQNCELL], the total number of re
[UINTRAFREQNCELL:NCellRncId] and [UINTRAFREQNCE
also the same as [UINTERFREQNCELL:NCellRncId] and [UIN
[UINTERFREQNCELL] is 256.
Service Interrupted After Modification: N/A
Impact on Network Performance: None
NCellId Neighboring Cell ID Meaning: Unique ID of a neighboring cell
GUI Value Range: 0~65535
Unit: None
Actual Value Range: 0~65535
MML Default Value: None
Recommended Value: None
Parameter Relationship:
-Configuration constraints:
When adding a [UINTRAFREQNCELL], the total number of re
[UINTRAFREQNCELL:NCellRncId] and [UINTRAFREQNCE
also the same as [UINTERFREQNCELL:NCellRncId] and [UIN
[UINTERFREQNCELL] is 256.
Service Interrupted After Modification: N/A
Parameter ID Parameter Name Parameter Desc

Impact on Network Performance: None


CIOOffset Neighboring Cell Meaning: CIO of a neighboring cell.
Oriented CIO This parameter works with CIO. The sum of CIOOffset, CIO,
evaluation or decisions on handovers triggered by the RNC. In a
moving the border of a cell.
In the case of an event-based intra-frequency measurement or in
trigger an event according to the sum of CIOOffset, CIO, and t
the value of this parameter when evaluating an inter-frequency m
In the case of a periodical inter-frequency measurement or inter-
initiate a handover based on the sum of CIOOffset, CIO, and th
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
MML Default Value: 0
Recommended Value: 0
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: The larger the value of this pa
this neighboring cell. The smaller the value of this parameter, th
neighboring cell.
CellsForbidden1A Affect 1A Threshold Meaning: Determines whether event 1A threshold is affected wh
Flag is set to "NOT_AFFECT", the relative threshold of event 1A is n
That is, the cell signals are N/A when the UE evaluates whether
to "AFFECT", the relative threshold of event 1A is affected whe
signals are involved when the UE evaluates whether event 1A sh
GUI Value Range: AFFECT, NOT_AFFECT
Unit: None
Actual Value Range: AFFECT, NOT_AFFECT
MML Default Value: AFFECT
Recommended Value: AFFECT
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: None
CellsForbidden1B Affect 1B Threshold Meaning: Flag of whether adding a cell into the active set will af
Flag This parameter is a flag of whether adding the cell into the activ
NOT_AFFECT: Adding the cell into the active set does not affe
Parameter ID Parameter Name Parameter Desc

signal will affect the UE evaluate whether event 1B should occu


the relative threshold of the event 1B. The cell signal will not af
GUI Value Range: AFFECT, NOT_AFFECT
Unit: None
Actual Value Range: AFFECT, NOT_AFFECT
MML Default Value: AFFECT
Recommended Value: AFFECT
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: None
SIB11Ind SIB11 Indicator Meaning: Whether to send the system information block 11 (SIB
details about SIB11, see 3GPP TS 25.331. If this parameter is se
included in SIB11. In this case, the neighboring cell cannot serv
UE in idle mode. If this parameter is set to TRUE, the neighbori
neighboring cell can serve as the target cell for access or cell res
GUI Value Range: FALSE(Do not send), TRUE(Send)
Unit: None
Actual Value Range: FALSE, TRUE
MML Default Value: TRUE(Send)
Recommended Value: TRUE(Send)
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: None
IdleQoffset1sn Offset 1 for Cell Meaning: Offset of the measured CPICH RSCP used for cell res
Reselection in Idle In a cell reselection procedure, the RNC subtracts this offset from
Mode and then ranks all neighboring cells. For details, see 3GPP TS 25
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
MML Default Value: 0
Recommended Value: 0
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: If this parameter is set to a gre
neighboring cell as the target cell reduces. If this parameter is se
neighboring cell as the target cell increases.
Parameter ID Parameter Name Parameter Desc

IdleQoffset2sn Offset 2 for Cell Meaning: Offset of the measured CPICH Ec/No used for cell res
Reselection in Idle In a cell reselection procedure, the RNC subtracts this offset from
Mode and then ranks all neighboring cells.
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
MML Default Value: 0
Recommended Value: 0
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: If this parameter is set to a gre
neighboring cell as the target cell reduces. If this parameter is se
neighboring cell as the target cell increases.
SIB12Ind SIB12 Indicator Meaning: Whether to send the SIB12 carrying the neighboring c
TS 25.331. If this parameter is set to FALSE, the neighboring in
is set to TRUE, the neighboring information is included in SIB1
cell is preferentially selected as the target cell for access or cell r
CELL_DCH).
GUI Value Range: FALSE(Do not send), TRUE(Send)
Unit: None
Actual Value Range: FALSE, TRUE
MML Default Value: FALSE(Do not send)
Recommended Value: FALSE(Do not send)
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: None
ConnQoffset1sn Offset 1 for Cell Meaning: Cell offset used for CPICH RSCP measurement value
Reselection in connected mode.
Connected Mode During cell selection or reselection, QOffset1sn is the cell offse
the cell offset corresponding to CPICH Ec/No. For details about
QOffset1sn and QOffset2sn are used when the UE is in idle mo
used when the UE is in connected mode. ConnQoffset1sn and C
is available. The measured value of the neighboring cell minus t
ranking. This parameter needs to be set based on the actual situa
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
Parameter ID Parameter Name Parameter Desc

MML Default Value: 0


Recommended Value: 0
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: If this parameter is set to a larg
parameter is set to a small value, the neighboring cell priority is
ConnQoffset2sn Offset 2 for Cell Meaning: Cell offset used for CPICH Ec/No measurement value
Reselection in connected mode.
Connected Mode During cell selection or reselection, QOffset1sn is the cell offse
the cell offset corresponding to CPICH Ec/No. For details about
QOffset1sn and QOffset2sn are used when the UE is in idle mo
used when the UE is in connected mode. ConnQoffset1sn and C
is available. The measured value of the neighboring cell minus t
ranking. This parameter needs to be set based on the actual situa
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
MML Default Value: 0
Recommended Value: 0
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: If this parameter is set to a lar
parameter is set to a small value, the neighboring cell priority is
TpenaltyHcsReselect HCS Cell Reselect Meaning: Penalty time for hierarchical cell reselection after a UE
Penalty Timer reselection function enables a UE in idle mode to reselect a hiera
GUI Value Range: D0, D10, D20, D30, D40, D50, D60
Unit: s
Actual Value Range: 0, 10, 20, 30, 40, 50, 60
MML Default Value: D0
Recommended Value: D0
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: If this parameter is set to a larg
reselections decreases, but the execution effect of hierarchical po
perform hierarchical cell reselections for a long period of time. I
time for hierarchical cell reselection shortens, but the number of
Parameter ID Parameter Name Parameter Desc

TempOffset1 HCS Cell Reselect Meaning: Cell offset used for CPICH RSCP measurement value
TempOffset1 If this parameter is set to INFINITY, a neighboring cell is not se
GUI Value Range: D3, D6, D9, D12, D15, D18, D21, INFINITY
Unit: dB
Actual Value Range: 3, 6, 9, 12, 15, 18, 21, INFINITY
MML Default Value: D3
Recommended Value: D3
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: If this parameter is set to a larg
cell as the target cell decreases. If this parameter is set to a small
as the target cell increases.
TempOffset2 HCS Cell Reselect Meaning: Cell offset used for CPICH Ec/No measurement value
TempOffset2 If this parameter is set to INFINITY, a neighboring cell is not se
GUI Value Range: D2, D3, D4, D6, D8, D10, D12, INFINITY
Unit: dB
Actual Value Range: 2, 3, 4, 6, 8, 10, 12, INFINITY
MML Default Value: D2
Recommended Value: D2
Parameter Relationship: None
Service Interrupted After Modification: No (Impact on the UE in
Impact on Network Performance: If this parameter is set to a larg
cell as the target cell decreases. If this parameter is set to a small
as the target cell increases.
NPrioFlag Neighboring Cell Meaning: Whether to configure the priority flag for a neighborin
Priority Flag The value FALSE indicates that the neighboring cell priority is n
combination, the cell with an invalid priority is the last one to be
The value TRUE indicates that the neighboring cell priority is co
When the algorithm of neighboring cell combination (controlled
enabled and the total number of neighboring cells to all cells in t
parameter as one of conditions for selecting the neighboring cell
preferentially selected. If a neighboring cell is not configured wi
this cell.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Parameter ID Parameter Name Parameter Desc

MML Default Value: FALSE


Recommended Value: FALSE
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: If this parameter is set to FAL
handover to this cell may fail, leading to call drops.
NPrio Priority of Meaning: Priority of a neighboring cell. The smaller the value of
Neighboring Cell neighboring cell. If NPrioFlag of a neighboring cell is set to Fal
If the total number of neighboring cells exceeds 32, the RNC co
neighboring cells. That is, a neighboring cell with a high priority
GUI Value Range: 0~30
Unit: None
Actual Value Range: 0~30
MML Default Value: None
Recommended Value: None
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: The higher the priority of a ne
delivered as a measurement object and the easier it will be to han
MbmsNCellInd MBMS Neighboring Meaning: Indicator for an MBMS neighboring cell. When this p
Cell Indicator is an MBMS neighboring cell. When this parameter is set to FAL
neighboring cell.
The Multimedia Broadcast Multicast Service (MBMS) feature p
services. It allows data to be transmitted from one source to mul
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
MML Default Value: TRUE
Recommended Value: TRUE
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: none
UintraNcellSRC Intra-Freq Neighbor Meaning: Source of neighboring cells. When this parameter is se
UMTS Cell Config When this parameter is set to SONOPTI, neighboring cells are c
Source optimization results. When this parameter is set to SONMEAS (
Parameter ID Parameter Name Parameter Desc

neighboring cells are temporarily configured during the optimiza


neighboring cells.
GUI Value Range: USER, SONOPTI, SONMEAS
Unit: None
Actual Value Range: USER, SONOPTI, SONMEAS
MML Default Value: USER
Recommended Value: None
Parameter Relationship: None
Service Interrupted After Modification: No (And no impact on t
Impact on Network Performance: None
DynCellShutDownFlag Dynamic Cell Meaning: Whether the load of neighboring cells is used to determ
Shutdown Flag Migration Type is set to PCPICHPOWERADJUST or whether t
GRADUALLY. When this parameter is set to TRUE, the load o
shut down or whether to start up a cell. When this parameter is s
to determine whether to shut down or whether to start up a cell.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
MML Default Value: FALSE
Recommended Value: FALSE
Parameter Relationship:
-Configuration constraints:
If the RNC ID specified by [UINTRAFREQNCELL:RNCId] an
[UINTRAFREQNCELL:NCellRncId] are different, [UINTRAF
to TRUE.
If the RNC ID specified by [UINTRAFREQNCELL:RNCId] an
[UINTRAFREQNCELL:NCellRncId] are different, [UINTRAF
toTRUE.
-Others:
This parameter takes effect when the RNC-level parameter DynC
parameter DynShutdownSwitch is set to ON_1, ON_2, or ON_3
Service Interrupted After Modification: No
Impact on Network Performance: None
Example

To add an intra-frequency neighboring cell (RNC ID = 1; Cell ID = 1; RNC ID


of neighboring cell = 9; Neighboring cell ID = 100; SIB11 Indicator = TRUE;
IdleQoffset1sn = 0; IdleQoffset2sn = 0; SIB12 Indicator = FALSE; HCS Cell
Reselect Penalty Timer = D0; The flag of the priority = FALSE), run the
following command:
ADD UINTRAFREQNCELL: RncId=1, CellId=1, NCellRncId=9, NCellId=100,
SIB11Ind=TRUE, IdleQoffset1sn=0, IdleQoffset2sn=0, SIB12Ind=FALSE,
TpenaltyHcsReselect=D0, NPrioFlag=FALSE;

You might also like