Professional Documents
Culture Documents
13 iPASOLINK 400)
iPASOLINK Introduction
Enumerate and explain the functions and features of each of the iPasolink Radio product.
Explain the iPasolink development Roadmap.
State the advantages of using the iPasolink Radios in the network.
Identify the Soft Keys and Hardware Keys needed for the required operation configuration of the
equipment.
Describe the operation functions of the iPasolink modules and interfaces.
Operate the Web-LCT of the iPasolink.
Establish the equipment configuration/mode of operation of the iPasolink
Establish the radio link and remote access and AMR configuration.
Establish the Network Management Configuration in preparation for remote access and NMS connection.
Create and configure additional users of different levels and privileges
Describe and explain the synchronization features and capabilities of the iPasolink
iPASOLINK Introduction
iPASOLINK is a modular network element that iPASOLINK 100E
integrates a comprehensive set of TDM cross
connect switching, packet switching and Ultra Compact
microwave / optical features, resulting in reduced All IP
costs and a long investments lifetime. The Pay as you grow architecture
following iPASOLINK series cover mobile Natural Cooling
backhaul requirements all the way from the
access tail links through to the metro aggregation
n e t w o r k .
iPASOLINK 1000
12-way Nodal
Redundancy
4-way Nodal
14 Universal Slots up to 4-way radio
Redundancy
High Speed INTF Two Universal Slots
Four universal Slots
SDH and All IP Redundancy
Pay as you grow architecture
with CWDM Low cost Compact design
iPASOLINK Introduction
iPASOLINK 100E
iPASOLINK 100E is a packet based
microwave radio system for high
speed data transport in an ultra
compact half the 19 inch rack size unit
with natural cooling containing single
built in modem.
Transmission Specification
Frequency bands: 6 to 42 GHz
Radio Transmission Capabilities:
・QPSK/16/32/64/128/256 QAM
Advanced Ethernet Functionalities ・ Hitless-AMR
・ LDPC FEC
VLAN ・ Port-based VLAN ・Transmission bandwidth 7, 14, 28 & 56 MHz
・ 802.1Q Tag-based VLAN ・ MTPC / ATPC
・ Q in Q (Tunnel) Interface :10/100/1000 Base-T
QoS ・ 802.1p CoS / ToS /Diffserv,MPLS EXP 1000 Base-SX / LX
・ Advanced QoS (for AMR)
Synchronous Ethernet
Ethernet OAM IEE802.1ag, ITU-T Y1731 Scalability and Flexibility
Link OAM IEEE 802.3ah
RSTP (802.1w), MSTP Pay as you grow concept
Link Aggregation (LACP) - software upgrade up to 460 Mbps
Ether Ring Protection ITU-TG.8031, 8032V2 - In-Band DCN
Header Compression
iPASOLINK Introduction
3
iPASOLINK 100/200
Transmission Specification
Frequency bands: 6 to 42 GHz
Radio Transmission Capacities:
・QPSK/16/32/64/128/256 QAM
・ Hitless-AMR
・ LDPC FEC
・Transmission Bandwidth 7,14,28 & 56 MHz
・ MTPC / ATPC
. Any combination of SDH / PDH / LAN traffic
Interface :10/100/1000 Base-T
Advanced Ethernet Functionalities 1000 Base-SX / LX
16 x E1,
1xSTM-1(thru)or 1x Channelized
VLAN ・ Port-based VLAN
・ 802.1Q Tag-based VLAN
・ Q in Q (Tunnel) Scalability and Flexibility
QoS ・ 802.1p CoS / ToS /Diffserv,MPLS EXP
・ Advanced QoS (for AMR)
Pay as you grow concept
- Synchronous Ethernet - software upgrade
- Ethernet OAM IEE802.1ag, ITU-T Y1731 Flexible configuration
- Link OAM IEEE 802.3ah - 1+0, 1+1 HS/SD/FD, XPIC(1+0)
- RSTP (802.1w), MSTP - Radio Aggregation (L2, L3)
- Link Aggregation (LACP) - 168xE1 Cross Connect SW
- Ether Ring Protection ITU-TG.8031, 8032V2 - PWE (SAToP)
- Header Compression (L2/L3) - Enhanced In-Band DCN
- TDM Ring Protection (SNCP)
- DHCP Relay/Sever Function
- In-Band DCN
iPASOLINK Introduction
4
iPASOLINK 400 A
Transmission Specification
Frequency bands: 6 to 42 GHz
Radio Transmission Capacities:
・QPSK/16/32/64/128/256/512/1024/2048 QAM
・ Hitless-AMR
・ LDPC FEC
・Transmission Bandwidth 7/14/28/40/56MHz
・ MTPC / ATPC
. Any combination of SDH / PDH / LAN traffic
Advanced Ethernet Functionalities Interface :10/100/1000 Base-T
1000 Base-SX / LX
VLAN ・ Port-based VLAN 16 x E1,
・ 802.1Q Tag-based VLAN 2xSTM-1(thru)or 1x Channelized
・ 802.1ad Provider Bridges
QoS ・ 802.1p CoS / ToS /Diffserv
- MPLS EXP
・ Advanced QoS (for AMR) Scalability and Flexibility
- Synchronous Ethernet
- RSTP (802.1w), MSTP Pay as you grow concept
- ERP ITU-T G.8031, 8032V2 - software upgrade
- Ethernet OAM, IEE802.1ag, ITU-T Y1731 Flexible configuration
- Link OAM IEEE 802.3ah - Two on board modems
- Link Aggregation 802.3ad with LACP - Two Universal slots
- Header Compression (L2/L3) - 1+0, 1+1 HS/SD/FD,XPIC (1+0),APS
* Future - Radio Aggregation (L2, L3, L1)
- 168xE1 Cross Connect SW
- PWE (SAToP)
- TDM Ring protection (SNCP)
- In-Band DCN
iPASOLINK Introduction
5
iPASOLINK 400
Transmission Specification
Frequency bands: 6 to 42 GHz
Radio Transmission Capacities:
・QPSK/16/32/64/128/256/512/1024/2048 QAM
・ Hitless-AMR
・ LDPC FEC
・Transmission Bandwidth 7/14/28/40/56MHz
・ MTPC / ATPC
. Any combination of SDH / PDH / LAN traffic
Interface :10/100/1000 Base-T
Advanced Ethernet Functionalities 1000 Base-SX / LX
16 x E1,
VLAN ・ Port-based VLAN 2xSTM-1(thru)or 1x Channelized
・ 802.1Q Tag-based VLAN
・ 802.1ad Provider Bridges
QoS ・ 802.1p CoS / ToS /Diffserv/ Scalability and Flexibility
- MPLS EXP
・ Advanced QoS (for AMR)
Synchronous Ethernet Pay as you grow concept
IEEE1588v2 (BC & slave) (Option Card) - software upgrade
RSTP (802.1w), MSTP Flexible configuration
ERP ITU-T G.8031, 8032V2 - 1+0, 1+1 HS/SD/FD,XPIC (1+0)/(1+1),APS
Ethernet OAM, IEE802.1ag, ITU-T Y1731 - Radio Aggregation (L2, L3, L1)
Link OAM IEEE802.3ah - 168xE1 Cross Connect SW
Link Aggregation 802.3ad with LACP - PWE (SAToP)
Header Compression (L2/L3) - Enhanced In-Band DCN
- DHCP Server/Relay Function
- TDM Ring Protection (SNCP)
- In-Band DCN
iPASOLINK Introduction
6
iPASOLINK 1000
Transmission Specification
Frequency bands: 6 to 42 GHz
Radio Transmission Capacities:
・QPSK/16/32/64/128/256/512 /1024/2048QAM
・ Hitless-AMR
・ LDPC FEC
・transmission Bandwidth 7/14/28/40/56MHz
・ MTPC / ATPC
. Any combination of SDH / PDH / LAN traffic
Interface :10/100/1000 Base-T
1000 Base-SX / LX
Advanced Ethernet Functionalities 10GbE (High Speed Interface)*
16 x E1,
VLAN ・ Port-based VLAN 2xSTM-1(thru)or 1x Channelized
・ 802.1Q Tag-based VLAN
・ 802.1ad Provider Bridges
QoS ・ 802.1p CoS / ToS /Diffserv/ Scalability and Flexibility
- MPLS EXP Pay as you grow concept
・ Advanced QoS (for AMR) - software upgrade
- RSTP (802.1w), MSTP Flexible configuration
- ERP ITU-T G.8031, 8032V2 - 1+0, 1+1 HS/SD/FD,XPIC (1+0)/(1+1), APS
- Ethernet OAM, IEE802.1ag, ITU-T Y1731 - Radio Aggregation (L1,L2,L3)
- Link OAM IEEE802.3ah - 1512xE1 (10 STM-1) Cross Connect SW
- Link Aggregation 802.3ad with LACP - TDM Ring Protection (SNCP)
- Header Compression (L2, L3) - DHCP Server / Relay Function
- PWE (SAToP )
- CWDM
- In-Band DCN
iPASOLINK Introduction
7
natural cooling
100E
100/200
1000
iPASOLINK Introduction 8
Native TDM
TDM based network is the bandwidth-guaranteed and synchronous network. It is free from time and
synchronization issues. However, TDM network can not manage the growth of data traffic efficiently.
Native IP
Unlike Native TDM network, IP based network can accommodate the growth of data traffic efficiently. In
addition, wiring work can be reduced dramatically as a result of shared connections.
However, IP-based network, due to its asynchronous and on-demand nature, does not guarantee synchronous delivery of
data. Therefore, synchronization issue due to fluctuation of delay, latency or jitter must be carefully considered in
transmission of mobile service.
Dual Native (Native TDM and Native IP)
Both packet switching and TDM cross connect are supported natively, which enables flexible transport per
traffic type on a single platform. Without incurring additional latency, delay/jitter sensitive traffic and clock such as 3GPP
Release-99 traffic is transmitted on TDM network directly, and IP based traffic such as LTE traffic is transmitted on IP
network directly without conversion. Moderate packet data growth may be efficiently aggregated by statistical multiplexing
while keeping the quality of delay/jitter sensitive TDM services..
TDM splitting (with PWE)
TDM splitting enables a port of legacy network traffic, such as HSPA data, to be dispensed onto IP network
with Pseudo-Wire Emulation (PWE), keeping only critical and timing-sensitive data on TDM network. With this functionality,
it is possible to streamline legacy network while increasing IP network usage.
PWE should be applied for transmission of jitter and latency relaxed services or where clock synchronization within mobile
RAN has been established by adoption of other synchronization measures.
Traffic Offload/Concentration
Traffic offload allows the operator to unload their IP traffic, including emulated legacy traffic, onto other cost
effective IP network. The benefit of traffic offloading is twofold: > Differentiation of services to customers
> Reduction of OPEX by converging voice and data traffic
In contrast to offload, concentration creates an opportunity for wholesale operators and carriers to maximize the utilization of
their networks by converging services and traffic from various customers .
iPASOLINK Introduction 9
iPASOLINK support both native TDM and native Ethernet. It is possible to provide TDM and Ethernet
Hybrid transmission or ALL IP transmission without external box within the same equipment. iPASOLINK
can provide flexible and optimized migration scenario according to network situations and customer
evolution
Access Aggregation Metro Core
2G/3G/LTE
BTS/Node-B E1
Packet network
MS5000
: Dual Native
: All IP (Hybrid) : Hybrid Split : Off Load : CWDM
iPASOLINK can provide end to end Ethernet connectivity with the extension of reach and capacity, nodal packet
radio, aggregation and bandwidth management. It is possible to use it also for WIMAX network and fixed network.
iPASOLINK Introduction 10
iPASOLINK 100E Application in IP network
Enterprise NW
Core
Network
100E link Back to Back
iPASOLINK Series
100E-200 link
Network
iPASOLINK Introduction
iPASOLINK Introduction 12
iPASOLINK Introduction 13
iPASOLINK Introduction 14
iPASOLINK capability for Evolution of Mobile Backhaul
TDM Based
BSC/ RNC
Network
BS
Option-1 Option-2
TDM + IP based Backhaul ALL IP based Backhaul
iPASOLINK Introduction
Risk free migration to All IP-1
The migration from TDM based network to All IP network is achieved
by simply adding the MSE (Multi Service Engine) card.
Hybrid Radio
16xE1
16xE1
Migration
16xE1
Note: Network needs to be synchronized by sync ETH , etc. MSE: Multi Service Engine
iPASOLINK Introduction 16
Risk free migration to All IP-2
The migration from TDM based network to All IP network is achieved
by simply adding the MSE (Multi Service Engine) card.
TDM transmission
16xE1
16xE1
Hybrid Radio
16xE1
16xE1
Packet transmission
Migration Packet Radio
MSE MSE
64xE
16xE1
Note: Network needs to be synchronized by sync ETH , etc.
1
MSE: Multi Service Engine
iPASOLINK Introduction 17
Using the STM-1, E1 and Ether BB options
16E1/MDR x 2 or
Channelized STM-1
16xE1
16xE1 FE or GbE
16xE1 32xE1
Ethernet
STM-1 STM-1
FE or GbE FE or GbE
STM-1 transparent
Ethernet
iPASOLINK Introduction 18
iPASOLINK XPIC (Cross Polarization Interference Canceller)
iPASO 200
iPASO 400
iPASO 1000
(In case of iPASOLINK200, no cable connection is required at the front panel for XPIC )
iPASOLINK Introduction 19
iPASOLINK Introduction 20
FEATURES-1
INTERFACES – 100E
• 2 x 10/100/1000 Base-T(X), 2 x 1000 Base –SX/LX SFP
• (No TDM Interfaces)
INTERFACES - 100/200
• 4 x 10/100/1000 Base-T(X), 2 x 1000 Base –SX/LX SFP
• 16 x E1 main board and 16xE1 option card or 1xSTM-1 optical /electrical
• MSE (Multi Service Engine) 16X E1 PWE option card
SAToP (RFC4553)
INTERFACES - 400
• 2 x 10/100/1000 Base-T(X), 2 x 1000 Base –SX/LX SFP (Main Board)
• 16 x E1 main board and 16E1 card (Universal slot)
• 2xSTM-1 optical /electrical (Universal slot)
• 2 x 10/100/1000 Base-T(X), 2 x 1000 Base –SX/LX SFP (Universal slot)
• MSE (Multi Service Engine) 64X E1 PWE card (Universal slot)
SAToP (RFC4553)
• Four front mounted universal slots are available for Modems and
option interface cards
iPASOLINK Introduction 21
FEATURES-2
INTERFACES -1000
• 2 x 10/100/1000 Base-T(X), 2 x 1000 Base –SX/LX SFP (Main Board)
• 16 x E1 card (Universal slot)
• 2xSTM-1 optical /electrical (Universal slot)
• 2 x 10/100/1000 Base-T(X), 2 x 1000 Base –SX/LX SFP (Universal slot) (2 Cards)
• 10 GbE (Universal slot)*
• CWDM High speed interface
• MSE (Multi Service Engine) 64X E1 PWE card (Universal slot) (2 Cards)
SAToP (RFC4553)
• Auxiliary Card ( HK, EOW B-B, NE2 etc.)
• Redundant Main card (TDM/L2 Switch matrix with CPU)
• Fourteen front mounted universal slots are available for Modems and
option interface cards
iPASOLINK Introduction 22
FEATURES-3
ADVANCED QoS FUNCTION – 100E/100/200/400/1000
•Enhanced QoS functions
Packet classification functions based on header information
(802.1p, IPv4 Precedence, IPv4/IPv6 DSCP. MPLS EXP
Bandwidth Management (Traffic shaping, CIR/PIR policing per port/VLAN)
Class mapping (4 or 8 Class queues for QoS control)
Congestion avoidance mechanism (WTD or WRED)
Flexible Scheduling (Deficit-weighted round robin or strict Priority)
ETHERNET / VLAN – 100E/100/200/400/1000
•TDM Cross connect: max 168 x 168 E1 left and right hand routes
•2 x STM-1 XC support
•Support SNCP
•Packet Switching: up to 40 Gbps
HYBRID SWITCHING FUNCTION-1000
• 1512 x 1512 E1 with support for 10 STM-1
•Support SNCP
•Packet Switching: up to 48 Gbps
Redundant Main card (TDM/L2 Switch matrix with CPU)
Note : The number of E1 channels depend on modulation scheme and TDM capacity
iPASOLINK Introduction 24
FEATURES-5
COMPACT AND RELIABLE PLATFORM
• Very compact and light platform for easy installation
1u IDU (100/200/400) 3U (1000)with GUI LCT for easy setting up
3/3.5 kg ODU
Backward compatible with Pasolink NEO series ODU
High reliability and quality backed by excellent field proven MTBF
Low Power consumption: adoption of high efficient RF components
VERSATILE RADIO SECTION
• High modulation up to 256 QAM (100E) for Native Ether
• High modulation up to 2048 QAM (400/400A/1000)for Native Ether and TDM
• High system gain using LDPC FEC and Linearizer techniques
• Adaptive modulation Radio (AMR)
• cross polarization interference canceller. (XPIC) [not for 100 & 100E]
•Double transmission capacity up to 920 mbps in 56 MHz BW
• Enhanced system gain with new ODU (IHG)
FREQUENCY AGILITY AND EASY TUNING
• Field tunable local oscillators (Synthesizer)
• RF Point Frequency can be changed through Local Craft Terminal (LCT)
• ODU Sub-band changeable by simply replacing the RF Filter.
iPASOLINK Introduction 25
FEATURES-6
SYNCHRONIZATION
•High Accuracy clock supply for clock synchronization
•Support both native TDM and synchronous Ethernet for clock reference
400 •IEEE 1588v2 with optional module (PTP-A) (BC and Slave)
•Support external clock input / output [not for 100E]
PROTECTION SCHEMES
iPASOLINK Introduction 26
FEATURES-7
SUPERB OAM FUNCTIONALITIES
•Loopback capability Near end, far end and IF loop-backs
400/1000•Modem Loopback: IF loop-backs and L2 Loop Back
•Ethernet OAM (IEE802.1ag / ITU-T Y.1731) and Link OAM IEEE 802.3ah
200•Fault detection, fault localization/isolation,
400/1000•Fault detection, fault localization/isolation, Performance measurement
•Link OAM IEEE 802.3ah
iPASOLINK Introduction 27
iPASOLINK 100E Features
6 – 38
42 GHz QPSK – 256 QAM AMR AMR
Hitless (1+0)/(1+1)
(1+0) LDPC
28
iPASOLINK Introduction
iPASOLINK 200 Features
6 – 42
38 GHz QPSK – 256 QAM AMR AMR
Hitless (1+0)/(1+1) 2 way XPIC LDPC
iPASOLINK Introduction 29
iPASOLINK 400A Features
VLAN Ether Ring TDM Ring LAG Ether OAM SYNC ETHER
iPASOLINK Introduction 30
iPASOLINK 400 Features
VLAN Ether Ring TDM Ring LAG Ether OAM SYNC ETHER IEEE 1588v2
iPASOLINK Introduction 31
iPASOLINK 1000 Features
RADIO AGGREGATION
GbE(SFP) 10/100/1000Base-T 16- xE1 2 x STM1 Super PDH PWE RSTP / MSTP 10GbE
iPASOLINK Introduction 32
iPASOLINK 1000 universal slot mounting
Slot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
N+0 1+0 1+0 1+0 1+0 1+0 1+0 1+0 1+0 1+0 1+0 1+0 1+0
Redundancy Group SWGRP1 SWGRP2 SWGRP3 SWGRP4 SWGRP5 SWGRP6
(1+1)Hot standby No1 No2 No1 No2 No1 No2 No1 No2 No1 No2 No1 No2
(1+1)Twin Path No1 No2 No1 No2 No1 No2 No1 No2 No1 No2 No1 No2
XPIC GRP1 XPIC GRP2 XPIC GRP3 XPIC GRP4 XPIC GRP5 XPIC GRP6
(1+0) XPIC
Master Slave Master Slave Master Slave Master Slave Master Slave Master Slave
(1+1) XPIC GRP1 (1+1) XPIC GRP2 (1+1) XPIC GRP3
(1+1) XPIC
Master1 Master2 Slave1 Slave2 Master1 Master2 Slave1 Slave2 Master1 Master2 Slave1 Slave2
Slot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Modem
16E1-A
STM1-A
GbE-A
MSE-A
AUX-A
PTP-A
1 2 3 4
5 6 7 8
9 MC-M
10 MC-M
11 12 13 14
Term PS PS
* Slot 12 MSE card can be used with SW Key for more than 64E1 PWE.
And can be used after using slot11 MSE card (F/W 3.01.04)
Radio Configurations (400)
iPASOLINK Introduction 34
Radio Configurations (Redundancy)
iPASOLINK 1000
iPASOLINK Introduction 35
Radio Configurations (XPIC)
Slot-1 Slot-2 Slot-3 Slot-4
iPASOLINK 1000
iPASOLINK Introduction 36
Radio Configurations - Nodal
Site-F
Site-C
2 way Nodal
Configurations
Site-A in one IDU
Site-B iPaso 200 iPASOLINK 200)
Site-D
iPaso 400
iPaso 400
iPaso 400
Site-E
iPaso 400
4 way Nodal Configurations in
one IDU (iPASOLINK 400)
iPASOLINK Introduction 37
Baseband Configurations
STM-1
2 x STM1
2 x STM-1
STM-1
All IP
MSE(PWE) card
16 x E1
PWE
E1 + Ether (Dual Native) GbE GbE
16 x E1 16 x E1
FE 16 x E1
152 E1
16 x E1 Super PDH 16 x E1
FE/GbE
16 x E1
iPASOLINK Introduction 38
iPasolink Radio using NEO ODU
PDH
NHG2
NHG2
NEO IDU
79 E1
NHG2
NHG2
STM-1 (63E1)
STM-1 (63E1)
79 E1 + LAN
NHG2
NHG2
iPASOLINK Introduction 39
• Ethernet Ring protection • TDM Ring protection
- Protection Switching Time - E1 SNCP
- Protection Switching Time
<2s (RSTP)
<50ms
< 50 ms ERP (ITU-T G.8032v2)
Ethernet Ring
TDM Ring
63 x E1 63 x E1 63 x E1 63 x E1
E1
63xE1(400)
Channelized STM-1
ERP – Ether Ring Protection (200/400) 32xE1(200)
iPASOLINK Introduction 40
40
• TDM Ring protection
- E1 SNCP
- Protection Switching Time
<50ms
E1
STM-1
STM-1
Mux
E1
E1
E1
E1
STM-1
STM-1
Mux
E1
E1
iPASOLINK Introduction 41
41
iPASOLINK 100E Block diagram
MODEM
CPU To ODU
Native
L2 SW
Packet line
LAN INTFC
Optional
Clock
-48V Power
Supply
iPASOLINK Introduction
iPASOLINK 200 Block diagram
MODEM
E1 INTFC DXC MODEM To ODU
16 x E1
(option)
Native
Channelized MUX/DEMUX Packet line
(option)
STM-1 / STM-1
(option)
Multi service L2 SW
Engine LAN INTFC
(option) Optional
Clock
Optional
ALM / AUX CPU
ALM/SC/CLK
Optional
-48V Power input Power
Supply FAN Module
options
iPASOLINK Introduction
iPASOLINK400 IDU Block Diagram
Auxiliary 16 x E1 INTFC IEEE 1588v2 PTP
4 x GbE MSE (64xE1 PWE) 2x STM-1
Modem PTP-A
Universal Slot-Cards
TDM SW L2 SW CPU
iPASOLINK Introduction 44
iPASOLINK 1000 IDU Block Diagram
Modem
Universal
Universal HSI
16 x E1 INTFC CWDM
slotslot
Universal
Universal #n-1#n
Universal slotHSI
4
2x STM-1
slotslot
#1 #2 slotHSI
3 10 GbE
MSE (64xE1 PWE) slot slotHSI
2
4 x GbE
slot #
Native TDM Bus
Native Packet Bus
FAN1
Control Bus
NMS/NE1
TERM-M
TDM SW L2 SW CPU 1xV.11/1xRS-232C
- 48V
PSPS
Optional
2xGbE Alarm
Clock - 48V
Main Board (SFP) DSC PSPS
Synchronous Ethernet Optional redundant
(Redundancy) 2xFE/GbE Clock
Power supply
FAN2
1xV.11/1xRS-232C
iPASOLINK Introduction 45
iPASOLINK 200/400 –Slots and Module configuration
No universal slot (All units are to be fixed before Shipment)
2 x Fast Ether OR 2 FE + 2 GbE OPTION CARDS
4x 10/100/1000Base-T Option
16 x E1 INTFC
ODU Interface LED Indication LCT / NMS LAN Ports
Ch STM-1 (or STM-1)
(1+0)/(1+1)/XPIC) (Status/Alarms) AUX HK DI/DO Multi Service Engine PS input
Universal Slot-Cards
Modem 4xGbE [2xRJ45, 2x(SFP)] Multi Service Engine 16 x E1 TDM INTFC
ODU Interface Channelized STM-1(or 2xSTM-1) AUX (HK Ext ALM) IEEE1588v2 PTP-A
Universal Slot-1 Universal Slot-2 Universal Slot-3 Universal Slot-4
iPASOLINK Introduction 46
iPASOLINK 1000 –Slots and Module configuration
Universal Slot-Cards
4xGbE [2xRJ45, 2x(SFP)] Multi Service Engine 16 x E1 TDM INTFC
Channelized STM-1(or 2xSTM-1) AUX (HK Ext ALM, NE2) Modem
GbE INTFC
FE1 / FE2 SFP
2xSTM-1 INTFC 16 x E1 INTFC
2 x GbE
Universal Slot-4
Main Card1
Main Card2
OW Jack
Protect SW
iPASOLINK Introduction 47
2FE or 4 X GbE (elect) 2 x GbE (LX/SX) 16 X E1 -48 VDC PS FAN
iPASOLINK Introduction 48
Top Cover to be removed for installation
Option-2 Option-1 Option-3
STM1-S
Top Cover to be removed for installation
STM-1 SFP
Optical S-1.1
iPASOLINK Introduction 49
iPASOLINK 100E IDU- INDICATORS
1 2 5 6 POWER INDICATOR
50
iPASOLINK 100E Introduction
iPASOLINK 200 IDU- INDICATORS & SWITCHES
iPASOLINK Introduction 51
2FE or 2 X GbE (elect) 2 x GbE (LX/SX) 16 X E1 -48 VDC PS FAN
iPASOLINK Introduction
iPASOLINK 400 Main Board -Indicators
Maintenance (Yellow)
Maintenance ON status Por1 (Green) Port 3(Green)
Alarm (Red)
Blink during reset, up / down LAN Link Status LAN Link Status
loading Alarm Status
Blink when data TX Blink when data TX
iPASOLINK Introduction 53
required
iPASOLINK Introduction
(40 Km)
iPASOLINK Introduction
iPASOLINK 1000 Main Board –Indicators/connectors
Port2 (Green) Port4(Green)
LAN Link Status LAN Link Status
Blink when data TX Blink when data TX
Maintenance (Yellow)
Maintenance ON status
Blink during reset, up / ON LINE Alarm (Red)
down loading ONLINE Status Alarm Status
Por1 (Green)
Port 3(Green)
LAN Link Status
LAN Link Status
Blink when data TX
Blink when data TX
iPASOLINK Introduction 56
♦ iPASOLINK 200/400 IDU INTFC pin assignments
iPASOLINK Introduction 57