You are on page 1of 7

   

Descriptions of 3TX RF Modules Flexi Multiradio BTS RF Module and Remote Radio
Head Description

Table 183 FRGS LEDs (Cont.)
LED color Description Alarm
Periodic Red and Green Antenna line device No alarm
faulty/degraded
Blinking Colors (Red, Yellow, Module highlighting (Flexi BTS No alarm
and Green), each color stable SM functionality that can help
for 0.5 second identifying faulty module)
RF Module fan/TX status LED: At least one fan is faulty or -
Red degraded
RF Module fan/TX status LED: All fans are working -
Green
RF Module fan/TX status LED: RF transmission is ON -
Color set according to fan
status, stable
RF Module fan/TX status LED: RF transmission is OFF -
Color set according to fan
status, blinking

Warnings, cautions or notes related to the product

f WARNING! Risk of electric shock!


Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for
example, feeder with antenna). However, if these conditions are not met, the plastic
caps that are delivered within the unused RF ports should remain in place. The plastic
caps isolate RF power from the environment, and thus provide electric shock security in
case RF power is accidentally on.

g Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond
extended limits, unit might shut down.

7.21 Flexi RFM 3-pipe 2100 240 W (FRGX)


FRGX technical specifications.
Functional description

Table 184 FRGX functional specification
Property Value
Output power 3x80 W
MIMO 2TX
Outdoor installation Yes
SW supported technology WCDMA, FDD-LTE
TX frequency range 2110-2170 MHz
RX frequency range 1920-1980 MHz
DL instantaneous bandwidth 60 MHz
UL instantaneous bandwidth 60 MHz
DL filter bandwidth 60 MHz

148 DN0951745 Issue: 20


   

Flexi Multiradio BTS RF Module and Remote Radio Descriptions of 3TX RF Modules
Head Description

Table 184 FRGX functional specification (Cont.)
Property Value
UL filter bandwidth 60 MHz

Interfaces

Figure 42 FRGX interfaces
ANT 5 ANT3 ANT2 ANT1
RXO3 TX/RX RXO2 TX/RX RX TX/RX
ANT6 ANT4
RX RX RET RXO1

GND EAC DCIN OPT3


OPT1 Fan/RF
LED Status MoistureVent
Module
OPT2
Status

Table 185 FRGX interfaces
Interface Label on the HW Number of Connector type Additional info
interfaces
Power connector DC IN 1 3-pole screw -
terminal
Antenna ANT 6 7/16 -
connector
RF output RxO 3 QMA -
connector
Remote Electrical RET 1 8-pin circular -
Tilt
External Alarm EAC 1 MDR36 -
Connection
Optical interface OPT 3 SFP 3 Gbps to 6 Gbps
Ground 1 M8 or dual M5 -
screws

Moisture Vent - 1 Core Vent -

Antenna Line Devices (ALDs) support

Issue: 20 DN0951745 149


   

Descriptions of 3TX RF Modules Flexi Multiradio BTS RF Module and Remote Radio
Head Description

Table 186 FRGX ALD support
ALD support via antenna ports Value
AISG ANT1, ANT3, ANT5, RET: AISG 2.0
Proprietary AISG1.1 No
CWA (for non-AISG installations) Yes
Voltage ANT1, ANT3, ANT5: 25 V or 12 V
ANT2, ANT4, ANT6: 12 V
RET: 25 V

Power per port 30 W

Functional block diagram

Figure 43 FRGX functional block diagram

RFModule Duplexfilter+DiversityRX

TX Bias-T
TX PA filter
VSWR
TX/RXRF
LNA
RX Det
EAC RXMain filter
RXOUT
LNA Bias-T
RX RX
RET RXDiversity filter

Bias-T
LNA
RX RX
RXDiversity
OpticalIF RF filter

control
OpticalIF RXOUT
RXMain RX Bias-T VSWR
filter TX/RXRF
LNA
TX Det
TX PA filter
OpticalIF Bias-T
LNA
RX RX
RXDiversity filter

RXOUT
RXMain RX Bias-T VSWR
filter TX/RXRF
LNA
TX Det
TX PA filter

DCIN
PSU

Fanassembly

Electrical specifications

Table 187 FRGX electrical specifications
Property Value
Nominal supply voltage -48.0 V DC
Nominal input voltage range -40.5 V DC to -57.0 V DC
Extended input voltage range -36.0 V DC to -40.5 V DC
-57.0 V DC to -60.0 V DC

150 DN0951745 Issue: 20


   

Flexi Multiradio BTS RF Module and Remote Radio Descriptions of 3TX RF Modules
Head Description

Power consumption

Table 188 FXEF power consumption
Mode Configuration Output power Estimated power consumption [W] at 48VDC
per carrier input at 25°C. Non-committed estimated
[W] values depend on the final product HW and
SW optimization with +/- 10% margin.
Average = (6h low hour load, 10h medium
hour load and 8h busy hour load) / 24h
Power Power Power
consumption consumption consumption
ETSI 202706 ETSI 202706 100% RF
average load busy hour power load
PRRH, static load PBH RRH, P100% RRH
static

g Note: Values preliminary estimated.

WCDMA 1/1/1 20 295 331 404


2/2/2 20 364 424 561
3/3/3 20 442 526 730
4/4/4 20 524 634 909
LTE 1/1/1 2T2R 20+20 584 664 811
1/1/1 2T2R 40+40 719 853 1129
1/1/1 2T2R 60+60 872 1063 1481
1/1/1 2T2R 80+80 1027 1277 1833

Installation and mechanical specifications

Table 189 FRGX installation and mechanical specifications
Property Value
Installation options • floor/stack installation
• pole installation
• wall installation
• 19'' rack/cabinet

IP rating IP65
Related optional items Pole installation

• Flexi Mounting Kit for Floor, Wall and Pole
(FMFA)
• Flexi Pole Kit (FPKA)
• Flexi Pole Kit (FPKC)
• Flexi Module Casing (EMHx)

Floor/Wall installation

Issue: 20 DN0951745 151


   

Descriptions of 3TX RF Modules Flexi Multiradio BTS RF Module and Remote Radio
Head Description

Table 189 FRGX installation and mechanical specifications (Cont.)
Property Value
• Flexi Mounting Kit for Floor, Wall and Pole
(FMFA)
• Flexi Module Casing (EMHx)

Outdoor 19'' rack
• Flexi Module Casing (EMHx)

Cabinet/indoor 19''' rack
• No optional items needed

Dimensions and weight

Table 190 FRGX dimensions and weight
Property Value Dimensions orientation
Height Core RFM: 118 mm (4.6 in.)
Depth Core RFM: 404 mm (15.9 in.)
Without front covers: 422 mm height
(16.6 in.)
depth
width
With front covers: 560 mm
(22.1 in.)

Width Core RFM: 441 mm (17.4 in.)
Without front covers: 447 mm
(17.6 in.)
With front covers: 492 mm
(19.4 in.)

Weight 25 kg (55.1 lb)
Volume 19.3 l

Environmental specifications

Table 191 FRGX environmental specifications
Property Value
Maximum operational outdoor temperature (at +55°C (131°F)
constant high ambient temperature maximum
output power might be limited)
Minimum operational temperature (including -35°C (-31°F)
cold start)

LEDs

152 DN0951745 Issue: 20


   

Flexi Multiradio BTS RF Module and Remote Radio Descriptions of 3TX RF Modules
Head Description

Table 192 FRGX LEDs
LED color Description Alarm
Red, stable Critical alarm affecting the Fault
whole RF module or all
antenna carriers
Red, blinking Operation degraded Major/critical alarm
• Major alarm affecting the
whole RF Module
• Major alarm affecting the
whole RF Module
• Major/Critical alarm
affecting a module
subcomponent or antenna
carrier

Yellow, stable • Until software download No alarm


begins
• The carriers are blocked
from BTS
• There is no connection to
any System Module

Yellow, blinking • Software download in No alarm


progress
• Configuration in progress:
RF resources are being
setup, but not yet activated

Green, stable • Software configuration is No alarm


complete or supervisory:
RF resources activated
and transmission is
possible
• Working normally, no
alarm on the RF Module

Green, blinking Software downloading and No alarm


updating
Stable Red for less than 5 Switched ON, but the next No alarm
seconds and changes to conditions are not reached yet
Stable Yellow
Stable Red for less than 5 The module is in the process No alarm
seconds of resetting
Periodic Red and Green Antenna line device No alarm
faulty/degraded
Blinking Colors (Red, Yellow, Module highlighting (Flexi BTS No alarm
and Green), each color stable SM functionality that can help
for 0.5 second identifying faulty module)
RF Module fan/TX status LED: At least one fan is faulty or
Red degraded
RF Module fan/TX status LED: All fans are working
Green

Issue: 20 DN0951745 153


   

Descriptions of 3TX RF Modules Flexi Multiradio BTS RF Module and Remote Radio
Head Description

Table 192 FRGX LEDs (Cont.)
LED color Description Alarm
RF Module fan/TX status LED: RF transmission is ON
Color set according to fan
status, stable
RF Module fan/TX status LED: RF transmission is OFF
Color set according to fan
status, blinking

f WARNING! Risk of electric shock!


Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for
example, feeder with antenna). However, if these conditions are not met, the plastic
caps that are delivered within the unused RF ports should remain in place. The plastic
caps isolate RF power from the environment, and thus provide electric shock security in
case RF power is accidentally on.

g Note: The maximum startup voltage is -40.5 V DC. If the input voltage is below/beyond
extended limits, unit might shut down.

154 DN0951745 Issue: 20

You might also like