You are on page 1of 12

UNIVERSAL REMOTE CONTROL INSTRUCTION MANUAL

One for All

Set-Top-Box TV Home Theater


Universal Remote Control Key Map

2 1
4 3
6 5

8 7
10 9
12 11
14 13
15
16
18
17
19
21 20
23 22
24

26
25
27 28
29 30

31

1
No. Key Description STB Mode (or no TV/AUDIO Mode
TV/AUDIO programmed) TV programmed only AUDIO programmed only TV+AUDIO programmed

1 Menu Menu - - -

2 Tools Tools - - -

3 Next Next - - -

4 Previous Previous - - -

5 Play/Pause play/pause - - -

6 Stop Stop - - -

7 Power Power Toggle TV Power Toggle TV Power toggle AUX Power toggle

8 TV - - - -

9 Forward Forward - - -

10 Rewind Rewind - - -

11 REC List Rec List - - -

12 REC Record - - -

13 Back Back TV Source TV Source -

14 Guide Guide - - -

15 Cursor Up Up - TV Vol+ -

16 OK OK - - -

17 Cursor Right Right - TV Mute -

18 Cursor Left Left - - -

19 Cursor Down Down - TV Vol- -

20 VOD VOD - - -

21 Vol +/- Vol+/-or PT TV Vol+/- AUX Vol+/- AUX Vol+/-

22 CH +/- CH+/- TV CH+/- TV CH+/- -

23 Home TV/IRD TV->STB TV->STB TV->STB

24 Audio Audio - - -

25 Numeric Keypad Numerics - - -

26 Subtitle Subtitle - - -

27 Media Media - - -

28 Info Info - - -

29 TV/Radio TV/Radio - - -

30 Mute Mute or PT TV Mute AUX Mute AUX Mute

31 Color Function Keys Red - - -


Green - - -
Yellow - AUX Source AUX Source
Blue - AUX Power AUX Power

2
Universal Remote Control Programming
for Etisalat Set Top Boxes

The default Set Top Box protocol may be programmed in the field using
the following procedure:

• Press the <Home> key, <REC> key and <OK> key simultanously for
3 sec, STB indicator LED will give a conformation blink and remain on.

• Release the keys and press a <Digit> key to select the Default Protocol.
Refer to the table below for the protocol selection.

• The LED will blink, indicating that the Default STB Protocol has been
programmed; the number of blinks corresponds to the Protocol
number selected, i.e. 1 blink for Protocol 1, 2 blinks for Protocol 2, etc.

Sr. No. SW Keys STB Model LED Confirmation

1 Digit2 Humax (eVision logo) Two blinks

2 Digit4 Airties Four blinks

3 Digit5 Kaon (Etisalat logo) Five blinks

4 Digit6 Kaon (eVision logo) Six blinks

5 Digit7 Huawei Seven blinks

6 Digit8 Pace Eight blinks

7 Digit9 Humax (Etisalat logo) Nine blinks

3
The Set top box protocol can be changed in the field to retune the RCU
to another STB using the following procedure:

• Press and hold key ‘Home’ and the relevant digit key together for a minimum
of 3 seconds, until the STB indicator LED blinks two times (of 500 ms each).
The new STB protocol is now programmed to non-volatile memory.

• Power on the STB and try out the dedicated STB buttons. If there is no
reaction on the STB, repeat the previous steps, for each code listed below.

Protocol Keys STB protocol


number
1 Home + Digit2 Humax (eVision logo)

2 Home + Digit4 Airties

3 Home + Digit5 Kaon (Etisalat logo)

4 Home + Digit6 Kaon (eVision logo)

5 Home + Digit 7 Huawei

6 Home + Digit 8 Pace

7 Home + Digit 9 Humax (Etisalat logo)

4
Quick Start Guide to set up the remote of your TV*

1. Switch on your TV

2. Press and hold the TV button on your remote


for 5 seconds. The TV button will light up.

3. Look up the 4-digit code for your brand


in the adjacent shortlist of brands. (Look at page no. 6)

Enter the 4-digit codes using the digit buttons.

4. Press and hold the Power button. Release the button


immediately as soon as the TV switches off.
(This step normally takes between 5 and 60 seconds).

5. Switch On your TV. Try out the volume channel buttons


on your remote. If those buttons are not working on your
remote control, repeat step4. until some button works.

Note: You can also learn the butttons from your


original remote. See next pages for details.

6. Press the TV button twice (2x) to finish setup

Important: If you made a mistake: Press the TV button twice to exit setup.
The red light under the TV button turns off. Restart from the beginning

5
Shortlist of brands*
Brands Brand
Name Number
Bang & Olufsen 0314
BenQ 0359
Blue Sky 0395
Bush 0445
Carrefour 0492
Daewoo 0692
Firstline 1008
Funai 1056
Grundig 1162
Hitachi 1251
Insignia 1368
JVC 1464
Lg 1628
Loewe 1660
Metz 1810
Mivar 1857
Nokia 2017
Panasonic 2153
Philips 2195
Pioneer 2212
RCA 2351
Samsung 2448
Sanyo 2462
Sharp 2550
Sony 2679
Toshiba 3021
Vizio 3211

If your brand is missing in this shortlist, look at the complete


BRAND LIST at the end of the user manual
Use '9999' as 4-digit code in case you cannot find your
brand in the BRAND LIST int the user manual. Note that
‘9999’ may result in a long setup (up to 15 minutes)

* For the full list of TV brands, visit www.etisalat.ae/elife 6


Turn on the TV/Audio

• Press and hold the <<TV>> key for 3 seconds; until the setup LED lights up.
This enables the protocol and brand selection function for the TV device, the
mode LED will remain on. To enable selection for AUX device, press <Mute>
key after hold <<TV>> key for 3 secs , the TV-mode led will give a Set-up
Confirmation blink.

• Release the key and enter the 4-digit Brand-id (please refer to brand ID
table guide) for the TV/AUX by pressing each digit key in sequence.
With the first 3 digits, the device-LED will give a reverse blink.
At the fourth digit, the device LED gives two reverse blinks and remains on
(the search will include all code sets that are linked to the selected brand,
or it will search through all code sets in the universal database if brand
number 0000 was selected).

• Press the <<POWER>> or <<MUTE>> key continuously; after 5 secs a


power or mute IR-command is transmitted for the next universal code-set
in the code-set list for the selected brand. The device-LED will turn off durin
tranmission of the IR-command. When the <<POWER>> or <<MUTE>>
key is held continuously then subsequent universal code-sets will be selected
automatically and a sequence of standby or mute IR-command of the next
universal code-set is transmitted.

In the case that brand number 0000 was selected the whole database of either
TV or Aux is scanned. The device-LED shows a reverse blink for each transmission.

7
• Press TV twice to confirm the code. The code that was selected when
TV was pressed twice or when 4 sec timeout happened is the code that
will be programmed into the remote. The RC will give a set-up confirmation
blink and go back to normal operation.

• All LEDs are turned off. Remarks.

• Universal code number “0000” will trigger a search through all codes
available in the remote independent of the brand.

• Timeout for 4 seconds happened if the user hasn’t pressed the TV key twice
to confirm the code. The code will be programmed into the remote;
the RC will give a set-up confirmation blink and go back to normal operation.

• During the setup, if user wants to restart TV device set-up, can press and
holding the <<TV>>key for 3 sec (step ii);if user want to restart AUX device,
can press <Mute> after holding the <<TV>>key for 3 sec, then the set-up
start from the beginning of the auto set-up again (step iii).

* For the full list of Audio devices programming codes, visit www.etisalat.ae/elife

8
In the case that brand number 0000 was selected the whole database of
either TV or Aux is scanned. The device-LED shows a reverse blink for each
transmission.

• Note that the search sequence continues by going through the whole list
after scanning through the brand list when all code-sets for the brand are
tested. It only stops when all code-sets of the whole database are tested.

• When the TV/AUX turns off or mute, the user must release the POWER or
MUTE key. The user should switch the TV/AUX on again with the original or
the universal remote control it device turn off. Now all keys can be tried
out with the universal remote control (inverse blinking if a universal
function-code is available under the key) including the POWER and MUTE
key. Press <<POWER>> or <<MUTE>> for 5 secs to continue the code-set
selection (item iv, above).

• If the 4 digit code is wrong or if another key than the <<POWER>> or


<<MUTE>> key is pressed after the 4 digits, Auto brand search will be
exited and the unit will not change the universal code-set number for the
respective device.

• Exiting a successful setup is via pressing the TV mode key twice or after
timeout.

9
After TV/Aux is also setup in addition to Etisalat STB set-up with the
remote, the remote control will control the volume of the TV/Aux only and
the STB volume control will not be managed from the remote any more.
In case one prefers however to continue to control the volume via the
STB and want the volume control to work for TV/Aux when selecting TV
(pressing TV) and volume control to work for STB when selecting
STB (pressing Home), the following need to be performed once.

Press Home and Mute simultaneously for 5 seconds until the light under
the TV keys blinks twice.

With the above steps you can toggle between TV/Aux and STB and there
will be volume control for TV while in TV mode and Volume control for
STB when in STB/Home mode.

10
For more information, please call 101 or visit www.etisalat.ae/elife

You might also like