You are on page 1of 17

HANSU CONTROLS

OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 1 OF 17
CATEGORY HA
SPECIFICATION & QUOTATION FOR INDUSTRIAL W.P.CAST ALUMINIUM JUNCTION BOXES
Supply of Cast Aluminum JUNCTION BOXES dust, vermain and weatherproof suitable for wall/Structure mounting. All the
enclosures are cast out of superior quality aluminum alloy. All the surfaces are carefully cleaned and levelled so as to give
very smooth surface. All the enclosures are chromatised and finally epoxy powder coated by static charge spray method by
light grey shade 631 as per IS5. Powder coating gives very tough durable and extremely smooth surface. All the mating
surfaces are provided with round rubber gasket in the groove so as to make it effectively dust and vermain proof. Typical
enclosures with different types of actuators mounted are tested by many of our customers for IP65 Class of protection. Our
Junction Boxes are suitable for outdoor installation without any canopy. MOUNTING: Mounting holes are inside or external
four lugs are provided for fixing. The lugs offset in such a way that the rear part of the unit stays away from the surface by at
least 3mm.FIXING OF TERMINALS: For wall mounting /Structure Mounting J.Box terminals are fixed inside the box. Cover
is fixed bolted type. CABLE ENTRIES: Threaded cable entries are provided on any side of Terminal Box. HARDWARE: All
external hardwares used will be Stainless Steel. EARTHING: Earthing is provided on both sides of the enclosures by 5mm
screw with two plain washers and spring washer of brass.
INSPECTION & TESTING: Each J.B.will be subjected to routine tests in accordance with relevant Indian Standards &
including the following :(1) Dimensional check as per drawing. (2) Operation test. (3) Insulation test with 500V Megger. (4)
HV Test at 2KV for 60 Seconds. (5) Earth continuity test.
SALIENT FEATURES OF `HANSU' J.B.:
(a) Each J.B. is in Cast Aluminium enclosure & epoxy powder coated.(b) Terminals are elmax clip on type, which are known
for quality and reliability. Even spares are available freely anywhere in India.(c) Better than IP65 Class of Protection.(d) Non
deteriorating Neoprene sponge rubber gasket.
SPECIFIC REQUIREMENT FOR INDUSTRIAL W.P.CAST ALUMINIUM JUNCTION BOXES
CODE DRAWING DESCRIPTION
HA04  Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)
with maximum 6: nos Elmax type 2.5sqmm. terminals. Required
threaded cable entries are provided on any side. Maximum 2:3/4”
entries can be provided on each side. External mounting legs are
provided for wall/structure
TYPE: HA04 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.
RONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA10 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)


with maximum 15: Nos 2.5sqmm. Elmax type terminals. Required
threaded cable entry is provided on any side. External legs are
provided for wall/structure mounting.
TYPE: HA10 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.

FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW


F/CATALOGUE J.B PAGE 2 OF 17
CODE DRAWING DESCRIPTION
HA11 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)
with maximum 20: Nos 2.5sqmm. Elmax type terminals. Required
threaded cable entry is provided on any side. External legs are
provided for wall/structure mounting.
TYPE: HA11 QTY:
Depth 110mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA14 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)


with maximum 30: Nos 2.5sqmm. Elmax type terminals. Required
threaded cable entries are provided on any side. External legs are
provided for wall/structure mounting.
TYPE: HA14 QTY:
DEPTH 165mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA15 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)


with maximum 36: Nos 2.5sqmm. Elmax type terminals. Required
threaded cable entries are provided on any side. External legs are
provided for wall/structure mounting.
TYPE: HA15 QTY:
DEPTH 110mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.
FRONT VIEW BOTTOM /TOP VIEW SIDE VIEW OPEN VIEW

HA16 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)


with maximum 46: Nos 2.5sqmm. Elmax type terminals. Required
threaded cable entries are provided on any side. External legs are
provided for wall / structure mounting.
TYPE: HA16 QTY:
DEPTH 150mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
F/CATALOGUE J.B PAGE 3 OF 17
CODE DRAWING DESCRIPTION
HA17 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 150: Nos 2.5sqmm. Elmax type terminals. Required threaded
cable entries are provided on any side. External legs are provided for
wall/structure mounting.
TYPE: HA17 QTY:
DEPTH 150mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA20 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 20: Nos 2.5sqmm. Elmax type terminals. Required threaded
cable entries are provided on any side. External legs are provided for
wall/structure mounting.
TYPE: HA20 QTY:
DEPTH: 100mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.
FRONT VIEW BOTTOM / TOP VIEW SIDE VIEW OPEN VIEW

HA21 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 36: Nos 2.5sqmm. Elmax type terminals. Required threaded
cable entries are provided on any side. External legs are provided for
wall/structure mounting.
TYPE: HA21 QTY:
DEPTH 110mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW OPEN VIEW TOP/BOTTOM VIEW SIDE VIEW

HA23 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 30: Nos 2.5sqmm. Elmax type terminals. Maximum of 8: ¾”
can be provided at the 170mm side and 14: ¾” cable entries can be
provided at the 275mm side. External legs are provided for wall/structure
mounting.
TYPE: HA23 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.

FRONT VIEW SIDE VIEW BOTTOM / TOP VIEW OPEN VIEW


F/CATALOGUE J.B PAGE 4 OF 17
CODE DRAWING DESCRIPTION
HA24 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 60: Nos 2.5sqmm. Elmax type terminals. Required threaded
cable entries are provided on any side. External legs are provided for
wall/structure mounting.
TYPE: HA24 QTY:
DEPTH 165mm
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.
FRONT VIEW SIDE VIEW BOTTOM / TOP VIEW OPEN VIEW

HA26 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes)


with maximum 15: Nos 2.5sqmm. Elmax type terminals. Required
threaded cable entries are provided on any side. External legs are
provided for wall/structure mounting.
TYPE: HA26 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE
TYPICAL AND ACTUAL PRODUCT WILL BE AS PER YOUR
SPECIFICATION AND ORDER.
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA39 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 8: Nos 2.5sqmm. Elmax type terminals. 2:3/4” threaded cable
entries are provided on top and on bottom side. External legs are
provided for wall/structure mounting.
TYPE: HA39 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA46 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 6: nos Elmax type 2.5sqmm. terminals. Required threaded
cable entries are provided on any side. Maximum 2:3/4” entries can be
provided at the bottom. External mounting legs are provided for
wall/structure
TYPE: HA46 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 5 OF 17
CODE DRAWING DESCRIPTION
HA48 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 20: nos Elmex type 2.5sqmm. terminals. Required threaded
cable entries are provided on any side. Maximum 4:3/4” entries can be
provided on the bottom side. External mounting legs are provided for
wall/structure
TYPE: HA48 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA49 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 30: nos Elmex type 2.5sqmm. terminals in vertical row.
Required threaded cable entries. Maximum 8:3/4” entries can be
provided at the bottom. External mounting legs are provided for
wall/structure
TYPE: HA49 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA50 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 24: nos Elmax type 2.5sqmm. terminals. Required threaded
cable entries are provided. Maximum 10:3/4” entries can be provided at
the bottom. External mounting legs are provided for wall/structure
TYPE: HA50 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA71 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 36: nos Elmax type 2.5sqmm. terminals in vertical row.
Required threaded cable entries are provided on any side. External
mounting legs are provided for wall/structure
TYPE: HA71 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW
F/CATALOGUE J.B PAGE 6 OF 17
CODE DRAWING DESCRIPTION
HA72 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 36: nos Elmax type 2.5sqmm. terminals. Required threaded
cable entries are provided on any side. Maximum 10:3/4” entries can be
provided on each side. External mounting legs are provided for
wall/structure
TYPE: HA72 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA73 Supply of Cast Aluminium (LM-6) Junction Boxes (Terminal boxes) with
maximum 36: nos Elmax type 2.5sqmm. terminals. Required threaded
cable entries are provided on any side. Maximum 10:3/4” entries can be
provided on each side. External mounting legs are provided for
wall/structure
TYPE: HA73 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

CATEGORY HA
SPECIFICATION AND QUOTATION FOR FRP JUNCTION BOXES
Supply of FRP J.B. dust, vermin and weather proof suitable for Wall/structure mounting. All the enclosures are HOT
moulded out of superior quality SMC compound. All the mating surfaces are provided with round rubber gasket so as to
make it effectively dust and vermin proof. Typical enclosures with different types of actuators mounted are tested by many
of our customers for confirmation to IP65 Class of protection. Our Junction Boxes are suitable for outdoor installation
without any canopy.MOUNTING :Internal holes are given for mounting. External legs can be provided, if required. CABLE
ENTRIES: Threaded cable entries are provided at the bottom or at top and on sides as per requirement.
HARDWARE: All external hardware used will be stainless steel. FIXING OF TERMINALS: For wall mounting /Structure
Mounting J. Box terminals are fixed inside the box. Cover is fixed bolted type.
INSPECTION & TESTING: Each J.B.will be subjected to routine tests in accordance with relevant Indian Standards
&including following (1) Dimensional check as per drawing. (2) Operation test. (3) Insulation test with 500V Megger. (4) HV
Test at 2KV for 60 Seconds. (5) Earth continuity test.
SALIENT FEATURES OF `HANSU' FRP TERMINAL BOXES:
(a)Each Terminal Box is in FRP enclosures and is hot moulded out of SMC/DMC compound. (b) Terminals are
Elmax/connectwell make, which are known for quality and reliability. Better than IP65 Class of Protection (c) Non-
deteriorating Neoprene sponge rubber gasket.S.S.Screws for cover fixing. (d) Superior finish
CODE DRAWING DESCRIPTION
HA35 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes (Terminal boxes) with maximum 30 nos 2.5sqmm elmex type
terminals. Required cable entries can be provided on any side. External
Mounting lugs are provided for wall /structure.
TYPE: HA35 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP – BOTTOM VIEW SIDE VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 7 OF 17
CODE DRAWING DESCRIPTION
HA40 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes with maximum 50 nos (in 2 rows) 2.5sqmm elmex type terminals.
Required cable entries can be provided on any side. MAX.20nos ¾” on
each side. External Mounting lugs are provided for wall /structure.
TYPE:HA40 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA41 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes (Terminal boxes) with maximum 105 nos 2.5sqmm elmex type
terminals. Required cable entries can be provided on any side.
MAX.36nos ¾” on 400mm side and 24 nos ¾” on 300mm side. External
Mounting lugs are provided for wall /structure.
TYPE: HA41 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM / TOP VIEW SIDE VIEW OPEN VIEW

HA42 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes with maximum 24 nos 2.5sqmm elmex type terminals. Required
cable entries can be provided on any side.
External legs will be provided for wall /structure.
TYPE:HA42 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

HA43 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes (Terminal boxes) with integral canopy covering three sides with
maximum 10 nos 2.5sqmm elmex type terminals. 3:3/4"cable entries can
be provided at bottom. External legs are provided for wall/structure
mounting.
TYPE: HA43 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.
FRONT VIEW BOTTOM IVEW SIDE VIEW OPEN VIEW
F/CATALOGUE J.B PAGE 8 OF 17
CODE DRAWING DESCRIPTION
HA44 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes (Terminal boxes) with integral canopy covering three sides with
maximum 30 nos 2.5sqmm elmex type terminals(Vertically) 6:3/4"cable
entries can be provided at bottom. External legs are provided for
wall/structure mounting.
TYPE: HA44 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA45 Supply of Hot Moulded FRP (Fiber Glass Re-inforced Polyster) Junction
Boxes (Terminal boxes) with integral canopy covering three sides with
maximum 24 nos 2.5sqmm elmex type terminals. 6:3/4"cable entries can
be provided at bottom. External legs are provided for wall/structure
mounting.
TYPE: HA45 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

SPECIFICATION & QUOTATION FOR INDUSTRIAL W.P. POLY CARBONATE JUNCTION BOXES
Supply of POLY CARBONATE JUNCTION BOXES dust, vermain and weatherproof suitable for wall/Structure mounting. All
the enclosures are moulded out of superior quality Poly Carbonate FR (Fire Ritardant) material. All the mating surfaces are
provided with round rubber gasket in the groove so as to make it effectively dust and vermain proof. Typical enclosures with
different types of actuators mounted are tested for IP65 Class of protection. Our Junction Boxes are suitable for outdoor
installation without any canopy. MOUNTING: External lugs are provided for fixing. The lugs offset in such a way that the rear
part of the unit stays away from the surface by at least 3mm.FIXING OF TERMINALS: For wall mounting /Structure Mounting
J.Box terminals are fixed inside the box. Cover is fixed bolted type. CABLE ENTRIES: Cable entries are provided on any
side of Terminal Box. HARDWARE: All external hardwares used will be Stainless Steel. INSPECTION & TESTING: Each
J.B.will be subjected to routine tests in accordance with relevant Indian Standards & including the following:(1) Dimensional
check as per drawing. (2) Operation test. (3) Insulation test with 500V Megger. (4) HV Test at 2KV for 60 Seconds. (5) Earth
continuity test.
SALIENT FEATURES OF `HANSU' J.B.:
(a) Each J.B. is in Poly Carbonate enclosure. (b) Terminals are elmax clip on type, which are known for quality and
reliability. Even spares are available freely anywhere in India.(c) Better than IP65 Class of Protection.(d) Non
deteriorating Neoprene sponge rubber gasket.
CODE DRAWING DESCRIPTION
HA61 Supply of POLY CARBONATE Junction Boxes (Terminal boxes) with
maximum 10: Nos 2.5sqmm Elmax terminals. 2:3/4” threaded cable
entries are provided on top and on bottom side. External legs are
provided for wall/structure mounting.
TYPE: HA61 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 9 OF 17
CODE DRAWING DESCRIPTION
HA62 Supply of POLY CARBONATE Junction Boxes (Terminal boxes) with
maximum 6: Nos Elmax type 2.5sqmm terminals. Required threaded
cable entries are provided on any side. Maximum 2:3/4” entries can be
provided on each side. External mounting legs are provided for
wall/structure
TYPE: HA62 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

CATEGORY HA
SPECIFICATION AND QUOTATION FOR FLAMEPROOF/WEATHER PROOF J.BOXES
Cast Aluminium LM6 J.Boxes dust, vermin and Flameproof /weatherproof suitable for wall/Structure mounting. All the
enclosures are cast out of superior quality Aluminium alloy. All the surfaces are carefully cleaned and leveled so as to give
very smooth surface. All the enclosures are chromatised and finally epoxy powder coated by static charge spray method by
light grey shade 631 as per IS5. Powder coating gives very tough durable and extremely smooth coating on the surface. All
the mating surfaces are provided with round rubber gasket in the groove so as to make it effectively dust and vermin proof.
Enclosures are tested at CMRI for flameproof and weather proof test IP65 as per IS 2147.Our Terminal Boxes suitable for
outdoor installation without any canopy. MOUNTING: External lugs are provided for fixing. FIXING OF TERMINALS: For
wall mounting /Structure Mounting Terminal Boxes terminals are fixed inside the box. Cover is fixed bolted type. CABLE
ENTRIES: Threaded cable entries are provided on any side. EARTHING: Earthing is provided on both sides of the
enclosures by 5mm screw with two plain washers and one spring washer. NAME PLATE: Each Terminal Box is provided
with nameplate giving equipment description. INSPECTION& TESTING: Each Box is subjected to routine tests in
accordance with relevant Indian Standards including following:
SPECIFIC REQUIREMENTS OF FLP/WP JUNCTION BOXES
CODE DRAWING DESCRIPTION
HA51 Design manufacture & supply of FLP\WP Junction Box in Cast Aluminium
LM-6 enclosure without canopy suitable for installation in gas group I, IIA
and IIB area complete with maximum 50 nos.2.5sqmm Elmax type
terminals in two rows. Maximum 10:3/4”ET cable entries can be provided
at the bottom. Maximum 2:1”ET cable entries can be provided on left
hand side & right hand side.
Certificate No CMRI\TC\359 Dt 9.7.97 Weight 10Kg.App
Type: HA51 Qty
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.

FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW


F/CATALOGUE J.B PAGE 10 OF 17
CODE DRAWING DESCRIPTION
HA52 Design manufacture & supply of FLP\WP Junction Box in Cast
Aluminium LM-6 encloser without canopy suitable for installation in gas
group IIA, IIB area and I complete with maximum 30A 4 way terminals.
1:3/4”ET cable entry can be provided on each side.
Certificate No CMRI\TC\H426 Dt 20.4.96 Wt.1.5Kg.App.n.
Type: HA52 Qty
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW SIDE VIEW OPEN VIEW (30A 4 WayTerminal)

HA53 Design manufacture & supply of FLP\WP Junction Box in Cast Aluminium
LM-6 enclosure without canopy suitable for installation in gas group I, IIA
and IIB area complete with maximum 12nos.2.5sqmm Elmax type
terminals. Maximum 6:3/4"ET cable entry can be provided at the
bottom.CMRI Certificate No CMRI\TC\H286 Dt 14.3.96 Wt.2.5Kg.App.
Type: HA53 Qty:
DEPTH 75MM
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HA54 Design manufacture & supply of FLP\WP Junction Box in Cast Aluminium
LM-6 enclosure without canopy suitable for installation in gas group I, IIA
and IIB area complete with maximum 24nos.2.5sqmm Elmax type
terminals. Maximum 8:3/4"ET cable entry can be provided at the bottom.
5:3/4"ET cable entry can be provided. CMRI Certificate No
CMRI\TC\H280 Dt 14.3.96 Wt.4.5Kg.App.
Type: HA54 Qty:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW SIDE VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 11 OF 17
CATEGORY HB
SPECIFICATION AND QUOTATION FOR CAST ALUMINIUM POLE MOUNTED J.B.
Supply of Cast Aluminium Pole Boxes dust, vermin and weatherproof suitable for Pole/Structure mounting. Shape of the
pole box makes it suitable to mount on round pole. All the enclosures are cast out of superior quality aluminum alloy. All the
surfaces are carefully cleaned and leveled so as to give very smooth surface. All the enclosures are chromatised and
finally epoxy powder coated by static charge spray method by light grey shade 631 as per IS5. Powder coating gives very
tough durable and extremely smooth surface. All the mating surfaces are provided with round rubber gasket in the groove
so as to make it effectively dust and vermin proof. Each pole box has provision to mount Fuse, Neutral link, Terminal.
Typical enclosures with different types of actuators mounted are tested by many of our customers for IP65 Class of
protection. Our Junction Boxes are suitable for outdoor installation without canopy.CABLE ENTRIES: 2/3 Nos Cable entries
are provided from bottom. NIPPLE: Suitable Nipple is provided at the back of pole box, which fits on pole hole in such a
way that transverse motion of box is prevented. Outgoing cable for streetlight can be taken through this Nipple. FIXING OF
TERMINALS: For pole mounting terminal Boxes terminals are fixed inside the box. Cover is fixed bolted type.
HARDWARE: All external hardware used will be Stainless Steel. EARTHING: Earthing is provided on both sides of the
enclosures by 5mm screw with two plain washers and spring washer of brass. INSPECTION & TESTING: Each Box is
subjected to routine tests in accordance with relevant Indian Standards and including the following:(1) Dimensional check
as per drawing (2) Operation test.(3) Insulation test with 500V Megger(4) HV Test at 2KV for 60 Seconds.(5) Earth
continuity test.
ADVANTAGE OF CAST ALU. POLE BOXES OVER SHEETSTEEL FABRICATED POLE BOXES.
(1) Cast Aluminium enclosures can be made in any desired and convenient shape and thus ensuring dust, vermin and
weatherproof ness. It is impossible to get any desired shape in sheet metal.(2) In case of Cast aluminum all
individual pieces will be exactly of same size and shape as these are cast out of same mould. Fabricated boxes are
likely to vary in shape on account of human error and other difficulties.(3)Finishing of cast Aluminium will be superb
and it is not possible in small-fabricated boxes.(4) Aluminium is lightweight and non-corrosive whereas sheet metal
is heavy and corrosive. Cast Aluminium has even good scrap value.
SALIENT FEATURES OF `HANSU' POLE BOXES:
(a) Each Box is in Cast Aluminium enclosures and epoxy powder coated.(b) Terminals are Balson /Elmax /connect well
make which are known for quality and reliability.(c) Better than IP65 Class of Protection.(d) Non deteriorating Neoprene
sponge rubber gasket.
SPECIFIC REQUIREMENTS FOR CAST ALUMINIUM POLE BOXES
CODE DRAWING DESCRIPTION
HB02 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Street Light
Pole Boxes with nipple entry at the back suitable for round pole complete
with either Kitkat fuse or HRC fuse or MCB. It will be complete with upto 35
sq mm Stud Type Terminals. Box is suitable for cables up to 4C x 35 sq
mm cable. 2:1” or 2:1.1/4” bottom entry will be provided. Arrangement for
fixing bracket is provided at the back.
TYPE: HB02 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW TOP VIEW OPEN VIEW

HB05 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Street Light
Pole Boxes with nipple entry at the back suitable for mounting on round
pole complete with either Kitkat fuse or HRC fuse or MCB. It will have
either 30A 4 way Terminal or up to 10 sq mm Elmax Terminals. Box is
suitable for cables up to 4C x 10 sq mm cable. 2:3/4” or 2:1” bottom entry
will be provided. Arrangement for fixing bracket is provided at the back.
TYPE: HB05 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW

.
F/CATALOGUE J.B PAGE 12 OF 17
CODE DRAWING DESCRIPTION
HB07 Supply of CAST ALUMINIUM Pole boxes with nipple entry at the back
with KITKAT type FUSE and 30A 4 Way terminal Block. 2:3/4"cable
entries will be provided at the bottom.
TYPE: HB07 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW TOP VIEW OPEN VIEW

HB08 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Street Light
Pole Boxes with nipple entry at the back suitable for round pole
complete with either Kitkat fuse or HRC fuse or MCB. Box is suitable
for cables up to 4C x 25 sq mm cable. 2:3/4” or 2:1” bottom entry will
be provided. TYPE: HB08 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

CATEGORY HB
SPECIFICATION AND QUOTATION FOR FRP STREET LIGHT POLE BOXES
Supply of FRP Street Light Pole Boxes dust, vermin and weather proof suitable for street light pole mounting. All the
enclosures are HOT moulded out of superior quality SMC compound. All the Mating surfaces are provided with round
rubber gasket so as to make it effectively dust and vermin proof. Typical enclosures are tested by many of our customers
for confirmation to IP65 Class of protection. Our Junction Boxes are suitable for outdoor installation without any canopy.
Each pole box has provision to mount Fuse, N.link, and Terminal.CABLE ENTRIES: 2/3 Nos Cable entries are provided
from bottom.NIPPLE: Suitable Nipple is provided at the back of pole box, which fits on pole hole in such a way that
transverse motion of box is prevented. Outgoing cable for streetlight can be taken through this Nipple.
FIXING OF TERMINALS: For pole mounting terminal Boxes terminals are fixed inside the box. Cover is fixed bolted type.
HARDWARE: All external hardware used will be Stainless Steel. INSPECTION & TESTING: Each J.B.will be subjected to
routine tests in accordance with relevant Indian Standards &including following:(1) Dimensional check as per drawing. (2)
Operation test. (3) Insulation test with 500V Megger. (4) HV Test at 2KV for 60 Seconds. (5) Earth continuity test
SALIENT FEATURES OF `HANSU' FRP Street Light Pole Boxes:
(a) Each Pole Box is in FRP enclosures and is hot moulded out of SMC/DMC Compound. (b) Terminals are
Elmax/connectwell make which are known for quality and reliability. (c) Better than IP65 Class of Protection (d) Non
deteriorating Neoprene sponge rubber gasket.S.S.Screws for cover fixing. (e) Superior finish.
SPECIFIC REQUIREMENTS FOR FRP POLE BOXES
CODE DRAWING DESCRIPTION
HB13 Design, Manufacturing & Supply of hot moulded FRP (Fibre Glass
Reinforced Polyester) Street Light Pole Boxes with nipple entry at the
back suitable for round pole complete with either Kitkat Fuse or HRC
Fuse or MCB. It will have either 30A 4 way Terminal or upto 35 sq mm
Stud Type Terminal. Box is suitable for cables up to 4C x 35 sq mm
cables. 2:1 1/4” or 2:1” bottom entry will be provided. Arrangement for
fixing bracket is provided at the back.
TYPE: HB13 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW TOP VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 13 OF 17
CODE DRAWING DESCRIPTION
HB14 Design, Manufacturing & Supply of hot moulded FRP (Filter Glass
Reinforced Polyester) Street Light Pole Boxes with nipple entry at the
back suitable for round pole complete with either Kitkat Fuse or HRC
Fuse or MCB. It will have either Integrally moulded Terminal or upto 16
sq mm Stud Type Terminal. Box is suitable for cables up to 4C x 16 sq
mm cables. 2:3/4” or 2:1” bottom entry will be provided. Arrangement for
fixing bracket is provided at the back.
TYPE: HB14 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW BOTTOM VIEW TOP VIEW OPEN VIEW

HB15 Supply of POLY CARBONATE Pole boxes with nipple entry at the
back with KITKAT type FUSE and 30A 4 Way terminal Block.
2:3/4"cable entries will be provided at the bottom.
TYPE HB15: QTY
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW BOTTOM VIEW TOP VIEW OPEN VIEW

HB16 Supply of hot moulded FRP (Fibre Glass Reinforced Polyester) Street
Light Pole Boxes with nipple entry at the back suitable for round pole
complete with either Kitkat Fuse or HRC Fuse or MCB. It will have
either 30A 4 way Terminal or 6 sq mm ELMEX Type Terminal. Box is
suitable for cables up to 4C x 6 sq mm cables. 2:3/4” bottom entry will
be provided. Arrangement for fixing bracket is provided at the back.
TYPE: HB16 QTY
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP / BOTTOM VIEW SIDE VIEW OPEN VIEW
F/CATALOGUE J.B PAGE 14 OF 17
CATEGORY HB
SPECIFICATION & QUOTATION FOR W.P.CAST ALUMINIUM TELEPHONE BOXES
Supply of Cast Aluminium JUNCTION BOXES dust, vermin and weatherproof suitable for Wall / Structure mounting. All the
enclosures are cast out of superior quality aluminum alloy. All the surfaces re carefully cleaned and leveled so as to give
very smooth surface. All the enclosures are chromatised and finally epoxy powder coated by static charge spray method by
light grey shade 631 as per IS5. Powder coating gives very tough durable and extremely smooth surface. All the mating
surfaces are provided with round rubber gasket in the groove so as to make it effectively dust and vermin proof. Typical
enclosures with different types of actuators mounted are tested by many of our customers for IP65 Class of protection. Our
Junction Boxes are suitable for outdoor installation without any canopy.
MOUNTING: Mounting holes are inside or external four lugs are provided for fixing. The lugs offset in such a way that the
rear part of the unit stays away from the surface by at least 3mm.
FIXING OF TERMINALS: For wall mounting /Structure Mounting J. Box terminals are fixed inside the box. Cover is fixed
bolted type. CABLE ENTRIES: Threaded cable entries are provided on any side of Terminal Box.
HARDWARE: All external hardware’s used will be Stainless Steel.
EARTHING: Earthing is provided on both sides of the enclosures by 5mm screw with two plain washers and spring washer
of brass. INSPECTION & TESTING: Each J.B. will be subjected to routine tests in accordance with relevant Indian
Standards & including the following:(1) Dimensional check as per drawing. (2) Operation test. (3) Insulation test with 500V
Megger.(4) HV Test at 2KV for 60 Seconds.(5) Earth continuity test.
SPECIFIC REQUIREMENT FOR W.P.CAST ALUMINIUM TELEPHONE BOXES
CODE DRAWING DESCRIPTION
HB32 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Telephone
Boxes (Terminal box) with 1 nos 10 pair Krone type terminal connector
for telephone cable 2:3/4"cable entries will be provided. External
Mounting legs are provided for wall/structure.
TYPE: HB32 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HB33 Design, Manufacturing & Supply Supply of Cast Aluminium (LM-6)


Telephone Boxes (Terminal box) with 2 Nos. 10 pair Krone type terminal
connector for telephone cable. 2:3/4"cable entries will be provided.
External Mounting legs are provided for wall/structure.
TYPE: HB33 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HB34 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Telephone


Boxes (Terminal box) with 3 Nos 10 pair Krone type terminal connector
for telephone cable. 2:3/4"cable entries will be provided. External
Mounting lugs are provided for wall/structure.
TYPE: HB34 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 15 OF 17
CODE DRAWING DESCRIPTION
HB35 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Telephone
Boxes (Terminal box) with 5 nos. 10 pair Krone type terminal connector
for telephone cable. 2:3/4"cable entries will be provided. External
Mounting legs are provided for wall/structure.
TYPE: HB35 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HB36 Design, Manufacturing & Supply of Cast Aluminium (LM-6) Telephone


Boxes (Terminal box) with 10 no 10 pair Krone type terminal connector
for telephone cable. 2:3/4"cable entries will be provided. External
Mounting lugs are provided for wall/structure.
TYPE: HB36 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

CATEGORY HB
SPECIFICATION AND QUOTATION FOR W.P. FRP TELEPHONE JUNCTION BOXES.
Supply of FRP J.B. dust, vermin and weather proof suitable for Wall/structure mounting. All the enclosures are HOT
moulded out of superior quality SMC compound. All the mating surfaces are provided with round rubber gasket so as to
make it effectively dust and vermin proof. Typical enclosures with different types of actuators mounted are tested by many
of our customers for confirmation to IP65 Class of protection. Our Junction Boxes are suitable for outdoor installation
without any canopy. MOUNTING :Internal holes are given for mounting. External legs can be provided, if required. CABLE
ENTRIES: Threaded cable entries are provided at the bottom or at top and on sides as per requirement. HARDWARE: All
external hardware used will be stainless steel. FIXING OF TERMINALS: For wall mounting /Structure Mounting J. Box
terminals are fixed inside the box. Cover is fixed bolted type. INSPECTION & TESTING: Each J.B.will be subjected to
routine tests in accordance with relevant Indian Standards &including following(1) Dimensional check as per drawing. (2)
Operation test. (3) Insulation test with 500V Megger. (4) HV Test at 2KV for 60 Seconds. (5) Earth continuity test.
SALIENT FEATURES OF `HANSU' FRP TELEPHONE TERMINAL BOXES:
(a) Each Terminal Box is in FRP enclosures and is hot moulded out of SMC/DMC compound. (b) Terminals are
Elmax/connectwell make which are known for quality and reliability. (c) Better than IP65 Class of Protection (d) Non
deteriorating Neoprene sponge rubber gasket. S.S.Screws for cover fixing. (e) Superior finish
F/CATALOGUE J.B PAGE 16 OF 17
SPECIFIC REQUIREMENT FOR W.P. FRP TELEPHONE JUNCTION BOXES
CODE DRAWING DESCRIPTION
HB23 Design, Manufacturing & Supply of Polycarbonate Telephone Junction
Boxes with 2nos 10 pair Krone type terminal connector for telephone
cable.2: 3/4"cable entries will be provided. Mounting holes are provided
inside for wall/structure
TYPE: HB23 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION.

FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HB24 Design, Manufacturing & Supply of Hot Moulded FRP (Fiber Glass Re-
inforced Polyster) Telephone Junction Boxes with 03 nos 10 pair Krone
type terminal connector for telephone cable. 2:3/4"cable entries will be
provided. External Mounting lugs are provided for wall/structure.
TYPE: HB24 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HB25 Design, Manufacturing & Supply of Hot Moulded FRP (Fiber Glass Re-
inforced Polyster) Telephone Junction Boxes with 04 nos 10 pair Krone
type terminal connector for telephone cable. 2:3/4"cable entries will be
provided. External Mounting lugs are provided for wall/structure.
TYPE: HB25 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HB26 Design, Manufacturing & Supply of Hot Moulded FRP (Fiber Glass Re-
inforced Polyster) Telephone Junction Boxes with 05 nos 10 pair Krone
type terminal connector for telephone cable. 2:3/4"cable entries will be
provided. External Mounting lugs are provided for wall/structure.
TYPE: HB26 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
HANSU CONTROLS
OFF: PLOT W-281, TTC INDUSTRIAL AREA, RABALE, MIDC, NEW MUMBAI-400 701.
TEL :( 022) 27690037, 65193145, CELL: 9821550302, FAX: 27690038, 25001021
WEB SITE:www.hansucontrols.com,E-Mail:hansucontrols29@rediffmail.com,hansucontrols@yahoo.com
F/CATALOGUE J.B PAGE 17 OF 17
CODE DRAWING DESCRIPTION
HB27 Design, Manufacturing & Supply of Hot Moulded FRP (Fiber Glass Re-
inforced Polyster) Telephone Junction Boxes with 10 nos 10 pair Krone
type terminal connector for telephone cable. 2:3/4"cable entries will be
provided. External Mounting lugs are provided for wall/structure.
TYPE: HB27 QTY:
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION
FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

SPECIFIC REQUIREMENT FOR INDUSTRIAL W.P. POLY CARBONATE TELEPHONE JUNCTION BOX
HB28 Supply of POLY CARBONATE Telephone Junction boxes with 10 Pair &
20 PAIR KRONE type TELEPHONE connector. 2:3/4"cable entries will
be provided at the bottom.
TYPE: HB28
NOTE: IMAGES, DRAWING AND WIRING DIAGRAM ARE TYPICAL
AND ACTUAL PRODUCT WILL BE AS PER YOUR SPECIFICATION

FRONT VIEW TOP/BOTTOM VIEW SIDE VIEW OPEN VIEW

You might also like