Professional Documents
Culture Documents
1 2
Function Buttons Handling The Remote Controller
TIPS FOR USING REMOTE CONTROL
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote NOT SURE WHAT A FUNCTION DOES?
control. The following is a brief introduction to the remote control itself. For instructions on how to Refer to the How to Use Basic Functions The remote control must be used within 8
operate your air conditioner, refer to the How to Use The Basic/Advanced Functions section of and How to Use Advanced Functions meters of the unit.
this manual. The unit will beep when remote signal is
sections of this manual for a detailed
NOTE:Please do not select HEAT mode if the machine you purchased is cooling only description of how to use your air conditioner. received.
type. Heat mode is not supported by the cooling only appliance. Curtains, other materials and direct
SPECIAL NOTE sunlight can interfere with the infrared
Button signal receiver.
ON/OFF Button designs on your unit may differ Remove batteries if the remote control
Starts and stops the louver slightly from the example shown.
Turns the unit on or off will not be used more than 2 months.
movement. If the indoor unit does not have, a particular Prevent any liquid from falling into the
Adjust Press this button, the horizon- function, pressing that function s button on remote controller.
tal louver swing up and down the remote control will have no effect. If other electrical appliances react to the
Increases temperature in automatically. Hold down this
0.5OC(1OF) increments. remote controller, either move these
button for 2 seconds, the INSERTING AND REPLACING BATTERIES appliances or consult your local dealer.
Hold down this button to
vertical louver will swing left Your air conditioning unit comes with two
increase temperature in
and right automatically. AAA batteries. Put the batteries in the
1OC(1OF) increments. Max.
Temperature is 30oC(86OF). remote control before use:
SET Button
1. Remove the back cover from the remote
Scrolls through operation control, exposing the battery compartment.
FAN SPEED functions as follows: 2. Insert the batteries, paying attention to
Selects fan speeds in Timer on( )g Timer off( ) match up the (+) and (-) ends of the
the following order: g Sleep( )g batteries with the symbols inside the
Turbo( )g
AU% g 100% g 80% battery compartment.
Fresh( )g Follow Me( )
g 60%g 40%g 20%. g Self Clean( ) 3. Install the back cover on.
Press the Adjust The selected symbol will flash
or button to increase INSTALLING REMOTE CONTROL HOLDER
SET on the display area, press the
/decrease the fan The remote controller can be attached to a wall
speed in 1% increments. or button to confirm.
or stand by using a remote controller holder.
Adjust FAN SPEED 1. Before installing the remote controller, check
Decreases temperature Selects fan speeds in that the air conditioner receives the signals Remove the back cover
in 0.5OC(1OF) increments. Mode the following order: properly. to install batteries
Hold down this button to AU% g 20%g 40% 2. Install the holder with two screws, or just put
decrease temperature g 60%g 80%g 100%. the holder on the desk.
in 1OC(1OF) increments. Press the Adjust 3. Put the remote controller on the holder.
Min. temperature is or button to increase
16OC(60OF). /decrease the fan
speed in 1% increments.
BATTERY NOTES
ECO/GEAR Button Button
,
Turns indoor unit s LED
For optimum product performance:
Starts and stops ECO Do not mix old and new batteries, or
feature. display and air conditioner
batteries of different types.
Press and hold down this buzzer on and off, which
Do not leave batteries in the remote control
button for 2 seconds to create a comfortable and ,
if you don t plan on using the device for
turn on the GEAR function. MODE quiet environment. Under more than 2 months.
Scrolls through operation this mode, the display will
modes as follows: illuminate for 10 seconds
while adjusting the mode, set BATTERY DISPOSAL
AUTO g COOLgDRY
temperature or fan speed, etc.
g HEAT gFAN
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for
proper disposal of batteries.
3 4
Remote LCD Screen Indicators How To Use The Basic Functions
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual SETTING TEMPERATURE
operation only the relative functional signs are shown on the display window. The operating temperature range for units is
16-30 OC/60-86 OF. You can increase or
ON/OFF display decrease the set temperature in 0.5 OC/1 OF
Appears when the unit is turned on,
increments.
and disappears when the it is turned off.
5 6
How To Use The Basic Functions How To Use The Basic Functions
HEAT operation
DRY operation(dehumidifying)
1. Press the MODE button to select
1. Press the MODE button to select DRY HEAT mode.
mode. 2. Set your desired temperature using
2. Set your desired temperature using the the Temp or Temp button.
Temp or Temp button. 3. Press the FAN button to select the
3. Press the ON/OFFbutton to start the unit. fan speed in a range of Au%-100%, in
, conjunction with Temp or Temp
NOTE: FAN SPEED can t be changed in button.
DRY mode. 4. Press the ON/OFF button to start the
3 unit.
4
SET
2
3 SET
2 NOTE: As outdoor temperature drops,the
,
performance of your unit s HEAT function
Mode may be affected. In such instances, we
Mode recommend using this air conditioner in
1 conjunction with other heating appliance.
1
FAN operation
unit.
,
NOTE: You can t set temperature in FAN, Mode
7 8
TIMER OFF function
Setting the TIMER function The TIMER OFF function allows you to NOTE: When setting the TIMER ON or
set a period of time after which the unit TIMER OFF functions, up to 10 hours,
1 2
Your air conditioning unit has two
timer-related functions:
x5 will automatically turn off, such as when
you wake up.
the time will increase in 30 minute
increments with each press. After 10
TIMER ON- sets the amount of timer after hours and up to 24, it will increase in 1
which the unit will automatically turn on. SET or 1. Press the SET button until an indicator
hour increments. The timer will revert to
TIMER OFF- sets the amount of time after " "( Timer off) appears and flashes.
By default, the last time period that you zero after 24 hours.
which the unit will automatically turn off. You can turn off either function by
set and an "h" (indicating hours)will
appear on the display. setting its timer to " 0.0h " .
TIMER ON function
The TIMER ON function allows you to set Note: This number indicates the
a period of time after which the unit will 3 4 amount of time after the current time
automatically turn on, such as when you that you want the unit to turn off.
come home from work.
3sec For example, if you set TIMER OFF for
5 hours, " 5.0h " will appear on the
1. Press the SET button until an indicator screen, and the unit will turn off after
" "( Timer on) appears and flashes. 5 hours.
By default, the last time period that you
set and an "h" (indicating hours)will 2. Press the Temp or Temp button
appear on the display. ON/
OFF
repeatedly to set the time when you want
Note: This number indicates the FA
MO
N
DE
TE
MP TIM
ER
SH
CUORT
T
the unit to turn on.
3. Wait 3 seconds, then the TIMER OFF
SLEE ON
P TIM
ER
that you want the unit to turn on. function will be activated. The digital
For example, if you set TIMER ON for Example: Setting unit to turn on after 2.5 display on your remote control will then
2.5 hours, " 2.5h " will appear on the hours. return to the temperature display. The
screen, and the unit will turn on after " " indicator remains on and this
2.5 hours. function is activated.
2. Press the Temp or Temp button
repeatedly to set the time when you want
the unit to turn on.
1 2
3. Wait 3 seconds, then the TIMER ON x10
function will be activated. The digital
display on your remote control will then
return to the temperature display. The SET or
" " indicator remains on and this
function is activated.
3 4
3sec
ON
/OFF
MOD
E SH
FA CUORT
N TE T
MP TIM
ER
SLEE ON
P TIM
ER
OF
F
9 10
Setting both TIMER ON and TIMER OFF at the same time Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off
(see the figure below)
Keep in mind that the time periods you set for both functions refer to hours after the
current time. For example, say that the current time is 1:00 PM, and you want the unit Your remote display
to turn on automatically at 7:00 PM. You want it to operate for 2 hours, then automa-
tically turn off at 9:00 PM.
Do the following:
Timer is set To turn ON
6 hours from current time
1 2 3 4
X12
3sec
SET or
Timer is set to turn OFF
8 hours from current time
ON
/OFF
MO
DE
SH
CUORT
TE T
MP TIM
ER
ON
5 6 7 8 Timer starts
Unit turns Unit turns
X16 ON OFF
3sec
SET or
ON
/OFF
MO
DE
SH
TE
MP TIM
CUORT
ER
T
11 12
How To Use The Advanced Functions How To Use The Advanced Functions
The SLEEP function is used to decrease Airborne bacteria can grow in the moisture NOTE: This function is only available under Press button and button
, that condenses around heat exchanger in COOL mode. simultaneously for one second to
energy use while you sleep (and don t need
the same temperature settings to stay the unit. With regular use, most of this Press ECO/GEAR button to enter the energy lock or unlock the keyboard.
comfortable). This function can only be moisture is evaporated from the unit. efficient mode in a sequence of following:
activated via remote control. When the SELF CLEAN feature is ECO GEAR(75%) GEAR(50%)
Previous setting mode ECO ......
see ,, sleep operation ,, in
activated, your unit will clean itself
,For the detail,
, USER ,
S MANUAL.
,, automatically. After cleaning, the unit will ECO operation:
turn off automatically.
Under cooling mode, press this button, the
Note: The SLEEP function is not You can use SELF CLEAN as often as remote controller will adjust the temperature
available in FAN or DRY mode. you like. automatically to 24OC, fan speed of Auto to
Note: You can only activate this function save energy(but only if the set temperature
in COOL or DRY mode. is less than 24OC). If the set temperature is
TURBO function( ) above 24OC , press the ECO button, the fan
speed will change to Auto, the set temperature
The TURBO function makes the unit work NOTE: will remain unchanged.
extra hard to reach your present temperature Press the SET button, NOTE:
in the shortest amount of time possible. the selected function Pressing the ON/OFF button, modifying the SET
When you select TURBO feature in COOL indicator will flash on mode or adjusting the set temperature to less
mode, the unit will blow cool air with the display area, press than 24OC will stop ECO operation.
strongest wind setting to jump-start the Temp or Temp Under ECO operation, the set temperature Mode
cooling process. button to confirm. The should be 24OC or higher. it may result in
When you select TURBO feature in HEAT indicator remains on insufficient cooling. If you feel uncomfortable,
mode, the unit will blow heat air with and this function is just press the ECO button again to stop it.
strongest wind setting to jump-start the activated.
heating process. GEAR operation:
To cancel the selected
Press this button to enter the energy efficient
function, just perform
mode in a sequence of following:
the same procedures 75% (up to 75% electrical energy consumption)
SET
as above.
FRESH function( )(optional) Hold together to activate
50% (up to 50% electrical energy consumption)
LOCK function
When the FRESH function is initiated, the Mode Previous setting mode
Ionizer/Plasma Dust Collector(depending Hold and FP function
This function is only available under COOL
on models) is energized and will help to buttons together for 3
seconds will alternate mode.
remove pollen and impurities from the air. When the air conditioner operates under
the temperature Under GEAR operation, the display on the
remote controller will alternate between heating mode with the set temperature
display between the
FOLLOW ME function( )(optional) O
C & OF scale. electrical energy consumption and set of 16 OC(60 OF), pressing button twice
temperature. in 2 seconds will activate 8 OC(46 OF)
The FOLLOW ME function enables the
remote control to measure the temperature ,heating.
,FP ,,. The indoor unit display shows
at its current location and send this signal Silence function
to the air conditioner every 3 minutes interval.
When using AUTO, COOL, or HEAT modes, Hold down Fan speed button( ) for 2 seconds
measuring ambient temperature from the to activate/cancel Silent mode. Due to low
remote control (instead of from the indoor frequency operation of compressor, it may result
unit itself) will enable the air conditioner to in insufficient cooling and heating capacity
optimize the temperature around (applicable to the air conditioner with Silent
you and ensure maximum comfort. feature only)
13 14