You are on page 1of 15

SPE 166281

EOR in Tight Oil Reservoirs through Wettability Alteration


Prateek Kathel, SPE, and Kishore K. Mohanty, SPE, The University of Texas at Austin

Copyright 2013, Society of Petroleum Engineers

This paper was prepared for presentation at the SPE Annual Technical Conference and Exhibition held in New Orleans, Louisiana, USA, 30 September–2 October 2013.

This paper was selected for presentation by an SPE program committee following review of information contained in an abstract submitted by the author(s). Contents of the paper have not been
reviewed by the Society of Petroleum Engineers and are subject to correction by the author(s). The material does not necessarily reflect any position of the Society of Petroleum Engineers, its
officers, or members. Electronic reproduction, distribution, or storage of any part of this paper without the written consent of the Society of Petroleum Engineers is prohibited. Permission to
reproduce in print is restricted to an abstract of not more than 300 words; illustrations may not be copied. The abstract must contain conspicuous acknowledgment of SPE copyright.

Abstract
In fractured reservoirs, the efficiency of water flood is governed by spontaneous imbibition of water into oil-containing
matrix blocks. When the matrix is oil-wet or mixed-wet, little oil can be recovered by imbibition. The objective of this work
is to identify chemicals that can be added to the injection water that can induce imbibition into an originally mixed-wet, tight,
fractured sandstone reservoir. Several surfactants were evaluated for their aqueous stability at the reservoir temperature and
salinity. Contact angles were measured on a clay-rich sandstone. Spontaneous imbibition tests were conducted on the
reservoir rocks. It is shown that the use of dilute (0.1 wt %) surfactant solution can alter the wettability from oil-wet towards
more water-wet condition on the mineral plates. Incremental oil recovery as high as 68% OOIP is obtained through
spontaneous imbibition experiments performed on tight (~10 µD) oil-wet/mixed-wet sandstone reservoir cores. Parametric
studies performed using numerical simulation show that the rate of oil recovery increases with increasing wettability
alteration, increasing fracture density, and decreasing oil viscosity.

Introduction
Because the conventional oil resources are fast depleting, it becomes imperative to develop methods to harness
unconventional oil resources like tight oil. The total tight oil reserves in North America are estimated to be more than 30
billion barrels contained in 24 oil reservoirs, among which only 14 reservoirs are under development (Forrest et al. 2011). A
large amount of oil in tight formations is still unrecovered. Primary recovery remains as low as 5.0-10.0% of original oil in
place, even after long horizontal wells have been drilled and massively fractured (Manrique et al. 2010). Oil recovery in tight
oil-wet fractured sandstone reservoirs is a challenge. The recovery efficiency by waterflooding is very low if the formation is
oil-wet and fractured (poor sweep) as no oil can be recovered through spontaneous imbibition and rock matrix remains
saturated with oil. The oil recovery in fractured tight oil reservoirs depends critically on the wetting properties of the rock
matrix. Large remaining oil after primary production in such reservoirs is a strong motivation to develop new secondary oil
recovery methods. Many researchers have investigated recovering oil by fracturing tight formations (Miller et al., 2008,
Buffington et al., 2010). There have been studies focused on CO2 injection in tight oil reservoirs (Arshad et al. 2009, Ren et
al. 2011), but existence of fractures in the formation is detrimental to CO2 flooding (Arshad et al. 2009) leading to poor
sweep and early breakthrough. This paper investigates an EOR technique based on wettability alteration of a mixed wet/oil
wet fractured tight oil sandstone formation.

Wettability is an important petrophysical property which impacts the rock fluid properties such as relative permeability,
capillary pressure and distribution of fluid phases. Wettability depends on the brine, oil and mineral compositions as well as
temperature (Anderson et al. 1986, Buckley, 2001, Gupta 2010). Wang and Gupta (1995) studied the influence of
temperature and pressure on wettability of reservoir rocks. Pressure did not have a significant effect on contact angle; in
contrast, temperature showed a significant effect on the wettability of crude-oil/brine/quartz systems. Using atomic force
microscopy, Kumar et al. (2008) have shown that wettability of a rock is controlled by adsorption of asphaltenic components
on the mineral surface.

In fractured reservoirs, if the wettability is altered to water-wet, large amount of oil can be recovered through spontaneous
imbibition. Wettability of a rock can be altered thermally (Al-Hadhrami et al. 2001) and chemically using surfactants, low
salinity brine (Nasralla et al. 2013) as well as through selective ions (Zhang et al. 2006, RezaeiDoust et al. 2009, Gupta et al.
2011). The thermal process needs a very high temperature (~200 °C); even the low salinity brine process needs a high
temperature (RezaeiDoust et al. 2010). Surfactants have the potential to alter wettability at low as well as high temperatures
2 SPE 166281

and they can also lower IFT at the oil-water interface. Past studies have identified cationic (Austad et al. 2003, Standnes and
Austad 2000a,b), anionic (Seethepalli et al. 2008, Adibhatla et al. 2008, Gupta et al. 2010) and non-ionic surfactants (Xie et
al. 2004, Gupta et al. 2010, Sharma et al. 2011) as wettability altering agents. Anionic surfactants make a good choice for
use as wettability alteration agents for sandstones because they have a negative charge like the sandstone surface which
results in low adsorption.

Different mechanisms for wettability alteration have been postulated in the literature. Kumar et al. (2008) proposed micellar
solubilization of adsorbed organic components by anionic surfactants. Standnes and Austad (2000) stated that wettability
alteration takes place by ion pair formation between the cationic surfactant and adsorbed negatively charged carboxylates
from oil on chalk surfaces. These ion pairs are dissolved in the oil phase and micelles. They further suggested that the
imbibition mechanism depends on desorption of organic material from the rock surface and water imbibing in the porous
media due to capillary forces. The desorption of organic molecules is related to diffusion of surfactant to the oil-water-rock
boundary and is regarded as the rate determining process during initial stages of imbibition.

The objective of this work is to find a wettability altering surfactant for a tight sandstone at the reservoir temperature (59 °C).
The aqueous stability of surfactants was studied at several salinities at the reservoir temperature. Oil-water interfacial tension
was measured at different salinities using a spinning drop tensiometer. Oil-surfactant solution contact angle was measured on
a clayey mineral. The efficacy of the surfactants was tested by numerous spontaneous imbibition experiments at two different
salinities. The scaling groups proposed in the literature for imbibition (Mattax et al. 1962, Ma et al. 1997) were tested with
our experimental data. Numerical simulations are performed with an in-house simulator developed in previous studies
(Adibhatla et al. 2005). Simulation results are validated against experimental data and various parameters are analyzed for
their effect on rate of oil recovery during spontaneous imbibition. The methodology and results are described next.

Methodology
Materials
Eight anionic surfactants (A1 to A8: alkyl ether sulphates and internal olefin sulphonates) and three nonionic surfactants (N1,
N2 and N3) were tested in this study. No cationic surfactants were used in this study owing to the negative surface charge of
sandstones. These surfactants are a combination of in-house developed surfactants and commercially available surfactants.
The formation brine contained 132,000 ppm (mg/L) of dissolved salts. Detailed composition of brine is listed in Table 1. All
the experiments were conducted with the reservoir dead oil. The contact angle tests were performed on Cristobalite mineral
plates (a mineral with quartz and Kaolinite which was similar to the mineral composition of field cores). The spontaneous
imbibition tests were performed on reservoir cores having permeability in the range of 10-100 µD. Actual undiluted field
stock tank oil was used for the study. Oil viscosity is 2.7 cp at the reservoir temperature and specific gravity is 0.78. Oil was
checked for contamination by measuring the oil-formation brine IFT which was around 21.8 dyne/cm (Hirasaki and Zhang,
2004).

Ion Ca2+ Mg2+ Na+ SO42- Cl- Total


Mass (mg/L) 2898 738 47654 250 81066 132606
Table 1: Formation brine composition

Aqueous Stability Test


Surfactant solutions were prepared in the formation brine and in half the salinity of the formation brine and kept at the
reservoir temperature for at least two weeks. The aqueous solutions were observed for precipitation and suspension
formation. A clear solution implies aqueous stability.

Interfacial Tension Measurement (IFT)


The IFT between the brine and oil phases was measured using a spinning drop tensiometer. Surfactant (0.1 wt %) was mixed
with brine at the desired salinity and then equilibrated with oil. IFT measurement was made between the equilibrated aqueous
and oleic phases.

Contact Angle Measurement


Surfactants which were aqueous stable at reservoir temperature were tested for wettability alteration. Cristobalite plates were
polished (Figure 1) on a 600 mesh diamond polisher. They were first aged in the formation brine for a day and then aged in
oil for around 7 days at 80 °C. They were then immersed in the surfactant solution and the change in contact angle was
observed for at least 2 days.
SPE 166281 3

Figure 1a: Mineral plate surface Figure 1b: Plate with oil drops, inside
an optical cell filled with a surfactant

Figure 2: An imbibition cell with a core immersed in a surfactant solution

Spontaneous Imbibition Test


Surfactants which altered the wettability on the Cristobalite plate were used for performing imbibition experiments on field
cores. This serves as a final check for the efficacy of the surfactant. The field cores were first saturated with the formation
brine and then the oil was injected. Cores were then aged in oil at 80 °C for about a month. Then the cores were placed in an
imbibition cell (Figure 2) surrounded by various brines or surfactant solutions. As the brine imbibed into the core, oil was
expelled and this oil floated to the neck of the cell where its volume was monitored. Ten imbibition experiments were
conducted. The core properties and fluids used in different experiments are listed in Table 2.
4 SPE 166281

Oil
Expt k Length Dia. IFT Recovery
No. Porosity (mD) (cm) (cm) Surfactant Brine Soi (dynes/cm) NB-1 (OOIP)
1 0.089 0.03 5.522 2.514 No Surf. FB 0.51 21.8 3383.2 0.15
2 0.133 0.236 5.584 2.517 A2 FB 0.75 3.73 248.7 0.57
3 0.103 0.035 5.542 2.52 A2 FB 0.79 3.73 573.1 0.54
4 0.101 0.03 5.535 2.522 A2 FB 0.71 3.73 613.8 0.68
5 0.093 0.056 5.536 2.517 A2 FB/2 0.76 7.32 845.9 0.67
6 0.101 0.056 5.645 2.516 A2 FB/2 0.8 7.32 864.5 0.61
7 0.134 0.239 5.573 2.523 A6 FB 0.66 5.64 376.1 0.46
8 0.101 0.103 5.513 2.521 A6 FB 0.72 5.64 502.9 0.52
9 0.131 0.148 5.6 2.518 A6 FB/2 0.72 6.8 567.1 0.6
10 0.096 0.071 5.538 2.521 A5 FB/2 0.79 10.1 1052.7 0.42

Table 2: Core properties and spontaneous imbibition results for different experiments

Results and Discussion


Aqueous Stability
Anionic surfactants. Figure 3 shows the aqueous stability results for anionic surfactants at the reservoir temperature. Ether
sulphates (A1, A2, A5, A6) showed better aqueous stability compared to internal olefin sulphonates (A7, A8). Higher salinity
diminishes aqueous stability of anionic surfactants. Only two out of the eight surfactants tested were aqueous stable at the
formation brine salinity. The number of ethoxy groups in the surfactant plays a major role in aqueous stability at higher
salinities. It was observed that more the number of ethoxy groups in the surfactant, the higher was the aqueous stability.

(FB) 13.2 Stable


Unstable
Salinity (wt%)

1: A1
2: A2
(FB/2) 6.6 3: A3
4: A4
5: A5
6: A6
7: A7
8: A8
0
0 1 2 3 4 5 6 7 8
Anionic Surfactant

Figure 3: Aqueous stability results for anionic surfactants

Nonionic surfactants. The non-ionic surfactants used during this study are of the form R-EOx where R is a hydrocarbon
attached to a chain containing x ethoxy groups. The three surfactants tested contained the same R but different (x) number of
ethoxy groups. For all the three surfactants, the cloud point was higher than the reservoir temperature and they resulted in
aqueous stable solutions even at high salinities as shown in Figure 4.
SPE 166281 5

(FB) 13.2
Stable

Salinity (wt%) Unstable

(FB/2) 6.6 1: N1
2: N2
3: N3

0
0 1 2 3
Non Ionic Surfactant

Figure 4: Aqueous stability results for non-ionic surfactants

Interfacial Tension
Figure 5 shows the IFT between the aqueous and the oleic phases as a function of salinity in the crude oil-brine-surfactant
systems. For both of these anionic surfactants IFT decreased with increase in salinity. Increase in salinity leads to more
competition between surfactant and salts for solubilization in water, as a result more surfactant monomers tend to move
towards the interface. More monomers at the interface result in lowering of the interfacial tension with the increase in
salinity.

15

13

11
A2
IFT (dynes/cm) 9
A6
7

3
0 5 10 15
Salinity (wt %)

Figure 5: IFT values for surfactant A2 and A6 with varying salinity.

Contact Angle
Figure 6 shows pictures of oil droplets on Cristobalite plates submerged in surfactant/brine solution in an optical cell and
Table 3 gives the contact angle values. The nonionic surfactants N1, N2 and N3 altered the contact angle, but not to the
extent required. Also it was observed that more the number of ethoxy groups (most in N3, least in N1), more was the change
in contact angle. But no non-ionic surfactant was able to make the Cristobalite plate water-wet (θ < 80°). Among the six
combinations of anionic surfactants which were aqueous stable, five altered the wettability from oil-wet to water-wet. Two
surfactants (A2 and A6) altered the wettability at both the salinities that we tested (formation brine and half the formation
brine). The average contact angles observed were nearly the same at both the salinities. These surfactants were then studied in
detail with regard to their interfacial tension variation with salinity and also reproducibility of spontaneous imbibition
experiments.
6 SPE 166281

FB 0.1 wt% A2 in FB/2

0.1 wt % A1 in FB/2 0.1 wt% A6 in FB/2

0.1 wt% A5 in FB/2 0.1 wt% A6 in FB

0.1 wt% A2 in FB 0.1 wt% N1 in FB

0.1 wt% N2 in FB 0.1 wt% N3 in FB

Figure 6: Oil droplets on Cristobalite plates submerged in surfactant/brine solutions


SPE 166281 7

Surfactant Brine Wt % Average Contact angle (°)


- FB - 150
A1 FB/2 0.1 130
A2 FB/2 0.1 72
A5 FB/2 0.1 74
A6 FB/2 0.1 70
A2 FB 0.1 74
A6 FB 0.1 74
N1 FB 0.1 145
N2 FB 0.1 110
N3 FB 0.1 90
Table 3: Contact angle results

Spontaneous Imbibition
Imbibition experiments were performed with the surfactants which altered the wettability of Cristobalite plates. Figure 7
shows an oil-wet reservoir core. A water drop placed on top of the aged core does not imbibe, confirming the oil-wetness of
the core.

Figure 7: A water drop on top of an aged core showing its oil wettability

Table 2 lists the results of the imbibition experiments. The oil recovery due to spontaneous imbibition is listed for each
experiment when an oil-saturated core plug is surrounded by different brines. Experiment 1 is for the formation brine. The oil
recovery is 15%, which suggests that the matrix is mixed-wet with a dominant oil-wet fraction. Three imbibition experiments
(Experiment 2-4) were performed with surfactant A2 in the formation brine (FB). Experiments 2 and 3 gave similar final oil
recovery values while Experiment 4 gave a significantly higher value. However, in these three cases with surfactant A2 the
recovery was high (54-68%) implying that the surfactant A2 is effective as a wettability altering agent. The difference in final
oil recovery can be attributed to heterogeneities in the core since these experiments were performed on different core plugs
from the same reservoir. Similarly for Experiments 5 and 6 for surfactant A2 in half the formation brine salinity (FB/2), the
oil recovery by spontaneous imbibition is also high (61-67%). Experiments 7 and 8 are for surfactant A6 in formation brine
which give oil recoveries of 46-52% OOIP. The lowest recovery (42%) was obtained for surfactant A5 (Experiment 10) in
half the formation brine salinity. The oil recovery by spontaneous imbibition is significant (42-68% OOIP) for surfactants
A2, A5 and A6.
The macroscopic inverse bond number is defined as the ratio of capillary to gravity forces, i.e.,



N B1  k
 gH (1)
where σ is the interfacial tension, φ is porosity, k is permeability, ∆ρ is the density difference, and H is the height of the core.
It is listed for the imbibition experiments in Table 2. High values of inverse bond number were obtained because of low
permeability of the cores, which implies that the capillary force exceeds the gravity force.
8 SPE 166281

Figure 8: Oil droplets at the outer surface of the cylindrical core plug during spontaneous imbibition experiment in
surfactant solution.
Figure 8 shows one of the cores placed in a surfactant solution. Oil droplets come out of the core on all sides as brine
imbibes. This suggests that the dominant imbibition mechanism is the counter current imbibition due to the capillary pressure
gradient caused by the wettability alteration. High values of inverse bond number imply high capillary forces compared to
buoyancy forces. If the wettability is altered, these capillary forces aid in the imbibition of brine through the periphery of the
core (Gupta et al. 2008).
Figure 9 shows the oil recovery as a function of time for the ten spontaneous imbibition experiments performed. The
experiment where no surfactant is used shows the lowest recovery (15 %). It takes 9 days before any oil is collected at the
neck of the imbibition cell. In this period the oil drops appeared on the periphery of the core, but they did not detach and
collect in the neck. For the surfactant solutions, 80% of the finally recovered oil is recovered in the first 20 days; the rate of
recovery gradually decreases as the saturation of aqueous phase increases in the core. The initial rate of oil recovery varied
significantly between the experiments.

0.80
Expt. 3: A2, FB
0.70
Expt. 2: A2, FB
Oil Recovery (frac. OOIP)

0.60 Expt. 4: A2, FB

0.50 Expt. 8: A6, FB
Expt. 7: A6, FB
0.40
Expt. 1: ‐, FB
0.30 Expt. 6: A2, FB/2
Expt. 10: A5, FB/2
0.20
Expt. 5: A2, FB/2
0.10 Expt. 9: A6, FB/2

0.00
0 10 20 30 40 50 60
Time (Days)

Figure 9: Oil recovery from spontaneous imbibition


SPE 166281 9

Some of the cores had almost the same initial oil saturation and imbibition was performed using the same surfactant, but at
different salinities. As a result of varying salinity the interfacial tension between oil/water is varied. Figures 10 and 11 show
the oil recovery curves for imbibition experiments performed with the same surfactant at different salinities. It was observed
that the rate of recovery was higher for the higher IFT cases. Also, ultimate oil recovery was higher for the higher IFT case in
both the sets.

0.80
7.32 dyne/cm
0.70
Oil Recovery (OOIP)

0.60
0.50
0.40 3.73 dyne/cm
0.30
0.20
0.10
0.00
0 10 20 30 40 50 60
Time (Days)
Expt. 2: A2, FB Expt. 5: A2, FB/2

Figure 10: Recovery rate comparison for surfactant A2

0.70

0.60
Oil Recovery (OOIP)

0.50

0.40

0.30

0.20

0.10

0.00
0 10 20 30 40 50 60
Time (Days)
Expt. 8: A6, FB Expt. 9: A6, FB/2

Figure 11: Recovery rate comparison for surfactant A6


Scaling Groups
Scaling groups are a means to analyze the spontaneous imbibition data as well as to predict oil recovery and recovery rates at
the field-scale. Several studies (Mattax and Kyte 1962, Ma et al. 1997) have identified scaling groups for different types of
porous media and Schmidt et al. (2012) attempted to find a universal scaling group for water-wet systems which can give
good correlation for all conditions. Mattax and Kyte (1962) scaling equation is given by:

k  1
tD  t (2)
  w L2
10 SPE 166281

Ma et al. 1997 scaling equation is given by:

k  1 Ld
tD  t , Lc  (3)
  o  w Lc
2
2 d 2  2 L2
where t D is dimensionless time, t is the actual time of imbibition, o is oil viscosity,  w is water viscosity, Lc is the
characteristic length. Our experimental data was plotted using Mattax and Kyte scaling equation (Eq. 2) as well as the scaling
group proposed by Ma et al. (Eq. 3). Figures 12 and 13 show that all the data do not fall on one curve, but the correlation was
slightly better for Ma et al. scaling group as compared to Mattax and Kyte (1962). Both the scaling equations are for strongly
water-wet porous media and are insufficient to explain the dynamics of changing wettability from oil-wet to water-wet.

1
Expt. 2: A2, FB

0.8 Expt. 4: A2, FB


Norm. Oil Recovery

Expt. 7: A6, FB
0.6 Expt. 8: A6, FB

Expt. 3: A2, FB
0.4
Expt. 6: A2, FB/2

Expt. 10: A5, FB/2


0.2
Expt. 5: A2, FB/2

0 Expt. 9: A6, FB/2


0.1 1 10 100
td

Figure 12: Imbibition data plotted with Mattax and Kyte dimensionless time.

1
0.9 Expt. 2: A2, FB

0.8 Expt. 4: A2, FB


Norm. Oil Recovery

0.7 Expt. 7: A6, FB

0.6 Expt 3: A2, FB

0.5 Expt 8: A6, FB

0.4 Expt. 6: A2, FB/2

0.3 Expt. 10: A5, FB/2

0.2 Expt. 5: A2, FB/2

0.1 Expt. 9: A6, FB/2

0
0.0001 0.001 0.01 0.1 1
td

Figure 13: Imbibition data plotted with dimensionless time given by Ma et al. (1997)
SPE 166281 11

Simulation
A mechanistic simulator developed in previous studies (Adibhatla et al. 2005) was used to perform parametric analysis after
successful lab-scale validation. The simulator uses a 3D finite volume, two-phase, four-component implicit numerical
scheme. There is no third phase formation observed during oil/brine/surfactant phase behavior experiments performed for our
system; hence the system is essentially two-phase. The numerical model takes into account surfactant convection/diffusion,
consequent IFT and contact angle changes. The injected surfactant moves into the matrix because of flow caused by
wettability alteration and IFT reduction.

The critical input parameters include capillary pressure (PC) and relative permeability curves (krj) as well as their variation
with surfactant concentration. Capillary pressure is assumed to depend on saturation through a power-law model.

PC ( S DW )  PCA  PCB ( S DW )nc (4)

In Eq. 4, PCA and PCB determine the endpoints of the capillary pressure curve, nc is the exponential parameter and S DW is the
dimensionless water saturation defined by

S j  S jr
S Dj  (5)
1  S wr  Sor

The capillary pressure depends on interfacial tension (  ) and contact angle (  ) according to

 cos
PC  PC 0 ( S DW ) . (6)
 0 cos0

The subscript ‘0’ on capillary pressure, interfacial tension and contact angle indicates values for an initial oil-wet system.
Relative permeability curves are described by a modified Brooks-Corey model, i.e.,

krj  krj0 ( S Dj )
nj
(7)

where krj0 is the endpoint relative permeability of phase j and n j is the exponential parameter for phase j. The endpoint
permeabilities and exponents vary with contact angle as follows:

cos  j  cos  0
krj0  kr0, wet  (kr0, nw  kr0, wet ) (8)
cos(  0 )  cos  0

and

cos  j  cos  0
n j  nwet  (nnw  nwet ) . (9)
cos(   0 )  cos  0

 j is the contact angle measured through phase j, kr0, wet corresponds to the wetting phase endpoint relative permeability and
kr0, nw corresponds to the non-wetting phase endpoint relative permeability. As the IFT is not reduced to an ultra-low value,
residual saturations are assumed constant.

IFT and contact angle variations with surfactant concentration are modeled as polynomial and linear functions, respectively,
with endpoint parameters obtained from experimental data. The values of different parameters used in the simulation are
provided in Table 4.
12 SPE 166281

Parameter Value
S or 0.25
k r0, wet 0.2
0
k r ,nw 0.9
nwet 4.5
nnw 2.25
 0 (rad) 0
PCA (Pa) 10342
PCB (Pa) 30000000
nc 1.3

Table 4: Values of parameters used in simulation


The reliability of the simulator is established by comparing the core scale simulation results with the results from laboratory
imbibition experiment 2 (Figure 14). Through the simulations, we have analyzed the effect of three parameters: extent of
wettability alteration, fracture spacing and oil viscosity on amount and rate of oil recovery.

Figure 14: Comparison of experimental and simulation results.

Figure 14 shows the comparison between numerical simulation and experiment 2. A good match is obtained between
simulated oil recovery and experimental data. There is a slight mismatch during the early period which can be due to the error
in measuring recovered volumes. When the oil-wet core is immersed in an imbibition cell and surrounded by brine/surfactant
solution, the entry capillary pressure opposes and exceeds the gravitational force for water influx from bottom; hence brine
does not imbibe immediately. As surfactant diffuses into the core, IFT and wettability of the core change. In our system the
IFT is not lowered to ultra-low IFT values, hence even after alteration of wettability which changes capillary pressure from
negative to positive, capillary pressure remains high and leads to significant counter-current imbibition. As the wettability is
altered towards water-wet, the relative permeability of the oil phase increases and enhances oil recovery.

The effect of wettability alteration on oil recovery was studied by changing the contact angle from initial value of 150° to
final values of 90° (intermediate-wet), 88° (slightly water-wet), 75° (water-wet) and 60° (more water-wet) . All other
parameters including IFT were same in all the cases. It was observed that by increasing the extent of wettability alteration,
rate of oil recovery increased as shown in Figure 15. The dominant recovery process is capillary pressure driven counter
current imbibition hence even a slight change towards water wet (88°) leads to high recovery rate compared to the
SPE 166281 13

intermediate wet case. As the contact angle decreases, the capillary pressure increases and the oil relative permeability
increases while the water relative permeability decreases. These factors increase the imbibition rate.

Figure 15: Effect of extent of wettability alteration on oil recovery.

Figure 16 shows the simulation results obtained by varying the fracture spacing: 1x represents the original diameter of the
core, 2x is for the core of twice the original diameter and so on. As the fracture spacing increases, the distance to transport the
fluids increases and the oil recovery rate (in terms of OOIP) decreases. Figure 17 shows the effect on oil recovery by
changing oil viscosity. Increase in viscosity of oil leads to low oil recovery rates. Hence imbibition driven recovery processes
are more suitable for light oils. An increase in oil viscosity leads to reduced oil mobility which can be compensated by
increased extent of wettability alteration and reduced fracture spacing to maintain desirable oil recovery rate.

Figure 16: Effect of fracture spacing on oil recovery.


14 SPE 166281

Figure 17: Effect of oil viscosity on oil recovery.

Conclusions
• Anionic surfactants A2, A5, and A6 alter the wettability of clay-rich sandstones.
• High oil recovery (42-68 %OOIP) is observed during imbibition experiments in very low permeability sandstones.
• The main recovery mechanism is capillary pressure gradient-driven counter-current imbibition due to wettability
alteration in these experiments.
• The rate of oil recovery increases with increasing IFT.
• Parametric studies performed using numerical simulation show that the rate of oil recovery increases with increasing
wettability alteration, increasing fracture density, and decreasing oil viscosity.

Acknowledgements
We are thankful to the sponsors of Chemical EOR Industrial Affiliates Project at The University of Texas at Austin for partial
funding of this work.

References
Adibhatla, B., and Mohanty, K. 2008. Oil Recovery from Fractured Carbonates by Surfactant-Aided Gravity Drainage: Laboratory
Experiments and Mechanistic Simulations. SPE Reservoir Evaluation & Engineering 11 (1): 119-130.
Adibhatla, B., Sun, X., and Mohanty, K. 2005. Numerical Studies of Oil Production from Initially Oil-Wet Fracture Blocks by Surfactant
Brine Imbibition. Paper SPE 97687 presented at the SPE International Improved Oil Recovery Conference in Asia Pacific, Kuala
Lumpur, 5-6 December.
Al-Hadhrami, H., and Blunt, M. 2001. Thermally Induced Wettability Alteration to Improve Oil Recovery in Fractured Reservoirs. SPE
Reservoir Evaluation & Engineering 4 (3): 179-186.
Anderson, W. 1986. Wettability Literature Survey-Part 1: Rock/Oil/Brine Interactions and the Effects of Core Handling on
Wettability. Journal of Petroleum Technology 38 (10): 1125-1144.
Arshad, A., Al-Majed, A., Menouar, H., Muhammadain, A., and Mtawaa, B. 2009. Carbon Dioxide (CO2) Miscible Flooding in Tight Oil
Reservoirs: A Case Study. Paper SPE 127616 presented at the Kuwait International Petroleum Conference and Exhibition, Kuwait
City, 14-16 December.
Austad, T., and Standnes, D. C. 2003. Spontaneous Imbibition of Water into Oil-Wet Carbonates. Journal of Petroleum Science and
Engineering 39 (3): 363-376.
Buckley, J. S. 2001. Effective Wettability of Minerals Exposed to Crude Oil. Current Opinion in Colloid & Interface Science 6 (3): 191-
196.
SPE 166281 15

Buffington, N., Kellner, J., King, J., David, B., Demarchos, A., and Shepard, L. 2010. "New Technology in the Bakken Play Increases the
Number of Stages in Packer/Sleeve Completions." Paper SPE 133540 presented at the SPE Western Regional Meeting, Anaheim, 27-
29 May.
Forrest, J., Birn, K., Brink, S., Comb, T.J., Cuthbert, B., Dunbar, R.B., Harju, J.A., Isaace, E., Jones, F., Khanna, P., Snarr, D.G., Sorensen,
J.A., Wall, T.J., and Whitney, D., 2011. Working Document of the NPC North American Resource Development Study, Paper #1-6,
Unconventional Oil, Tight Oil.
Gupta, R., and Mohanty, K. 2010. Temperature Effects on Surfactant-Aided Imbibition into Fractured Carbonates. SPE Journal 15 (3):
588-597.
Gupta, R., Adibhatla, B., and Mohanty, K. 2008. Parametric Study to Enhance Oil Recovery Rate from Fractured Oil-Wet Carbonate
Reservoirs. Paper SPE 116485 presented at the SPE Annual Technical Conference and Exhibition, Denver, 21-24 September.
Gupta, R., Smith, G., Hu, L., Willingham, T., Lo Cascio, M., Shyeh, J., and Harris, C. 2011. Enhanced Waterflood for Carbonate
Reservoirs-Impact of Injection Water Composition. Paper SPE 142668 presented at the SPE Middle East Oil and Gas Show and
Conference, Manama, 25-28 September.
Kumar, K., Dao, E., and Mohanty, K. 2008. Atomic Force Microscopy Study of Wettability Alteration by Surfactants. SPE Journal 13 (2):
137-145.
Ma, S., Morrow, N. R., and Zhang, X. 1997. Generalized Scaling of Spontaneous Imbibition Data for Strongly Water-Wet
Systems. Journal of Petroleum Science and Engineering 18 (3): 165-178.
Manrique, E., Thomas, C., Ravikiran, R., Izadi Kamouei, M., Lantz, M., Romero, J., and Alvarado, V. 2010. EOR: Current Status and
Opportunities. Paper SPE 130113 presented at the SPE Improved Oil Recovery Symposium, Tulsa, April 24-28.
Mattax, C. C., and Kyte, J. R. 1962. Imbibition Oil Recovery from Fractured, Water-Drive Reservoir. SPE Journal 2 (2): 177-184.
Miller, B., Paneitz, J., Yakeley, S., and Evans, K. 2008. "Unlocking Tight Oil: Selective Multistage Fracturing in the Bakken Shale." Paper
SPE 116105 presented at the SPE Annual Technical Conference and Exhibition, Denver, 21-24 September.
Nasralla, R., Bataweel, M., and Nasr-El-Din, H. 2013. Investigation of Wettability Alteration and Oil-Recovery Improvement by Low-
Salinity Water in Sandstone Rock. Journal of Canadian Petroleum Technology 52 (2): 144-154.
Ren, B., Xu, Y., Niu, B., Ren, S., li, X., guo, P., and Song, X. 2011. Laboratory Assessment and Field Pilot of Near Miscible CO2 Injection
for IOR and Storage in a Tight Oil Reservoir of ShengLi Oilfield China. Paper SPE 144108 presented at the SPE Enhanced Oil
Recovery Conference, Kuala Lumpur, 19-21 July
RezaeiDoust, A., Puntervold, T., Strand, S., and Austad, T. 2009. Smart Water as Wettability Modifier in Carbonate and Sandstone: A
Discussion of Similarities/Differences in the Chemical Mechanisms. Energy & fuels 23 (9): 4479-4485.
RezaeiDoust, A., Puntervold, T., and Austad, T. 2010. A Discussion of the Low-Salinity EOR Potential for a North Sea Sandstone Field.
Paper SPE 134459 presented at the SPE Annual Technical Conference and Exhibition, Florence, 19-22 September.
Schechter, D. S., Zhou, D., and Orr, F. M. 1994. Low IFT Drainage and Imbibition. Journal of Petroleum science and Engineering 11 (4):
283-300.
Schmid, K. S., and Geiger, S. 2012. Universal Scaling of Spontaneous Imbibition for Water-Wet Systems. Water Resources Research 48
(3), doi: 10.1029/2011WR011566.
Sharma, G., and Mohanty, K. 2011. Wettability Alteration in High Temperature and High Salinity Carbonate Reservoirs. Paper SPE
147306 presented at the SPE Annual Technical Conference and Exhibition, Denver, 30 October-2 November.
Song, C., and Yang, D. T. 2012. Optimization of CO2 Flooding Schemes for Unlocking Resources from Tight Oil Formations. Paper SPE
162549 presented at the SPE Canadian Unconventional Resources Conference, Calgary, 30 October-1 November.
Standnes, D. C., and Austad, T. 2000. Wettability Alteration in Chalk: 1. Preparation of Core Material and Oil Properties. Journal of
Petroleum Science and Engineering 28 (3): 111-121.
Standnes, D. C., and Austad, T. 2000. Wettability alteration in chalk: 2. Mechanism for Wettability Alteration from Oil-Wet to Water-Wet
using Surfactants. Journal of Petroleum Science and Engineering 28 (3): 123-143.
Wang, W., and Gupta, A. 1995. Investigation of the Effect of Temperature and Pressure on Wettability Using Modified Pendant Drop
Method. Paper SPE 30544 presented at the SPE Annual Technical Conference and Exhibition, Dallas, 22-25 October.
Zhang, P., and Austad, T. 2006. Wettability and Oil Recovery from Carbonates: Effects of Temperature and Potential Determining
Ions. Colloids and Surfaces A: Physicochemical and Engineering Aspects 279 (1): 179-187.

You might also like