Professional Documents
Culture Documents
Singapore 339156
1. CAUTION English
The UPS battery has been fully charged before leaving our factory. During the shipment,
some level of power may have been discharged. In order to ensure the efficiency of the UPS,
please allow the UPS to charge its battery for at least 12 hours before use.
Connect the UPS to a two-pole, three-wire grounding mains (AC). The AC source must be
connected to appropriate branch protection (fuse or circuit breaker). Connection to any other
type of AC source may result in a shock hazard and may violate your warranty claim.
This UPS has an internal battery and its energy can not be de-energized by the user. The
output may be energized even though when the UPS is not connected to the main AC.
DO NOT install the UPS in locations where there is water or excessive humidity.
DO NOT allow water or any foreign object to enter the UPS or put any objects containing
liquid on or near the UPS.
DO NOT remove the cover. No user serviceable parts. Refer servicing to qualified service
personnel.
DO NOT connect any non-computer peripherals to the UPS. The UPS is designed for use
with computer loads only.
To reduce the risk of overheating the UPS, avoid exposing the unit to direct sunlight. Avoid
installing the unit near heat emitting appliances such as a room heater or stove.
1
2. OPERATION
2.1 Operating Instructions
A. Connect the AC input power cable of your UPS to the AC Power. ‘YELLOW’ LED on
the UPS front panel is lit. UPS is charging the battery. (Note: DO NOT connect any
load to your UPS until the UPS has charged its battery for 12 hours)
B. Plug computer and monitor to UPS sockets. (Note: Power of computer and monitor
must be less than the maximum total power of your UPS. DO NOT connect a laser
printer to the UPS backup socket. Laser printers draw a significantly more power
than other types of equipment and may overload the UPS.)
C. Switch on the UPS by pressing the power switch on the front panel. The ‘GREEN’ LED
on the UPS front panel is lit and ‘YELLOW’ LED is off. UPS is supplying utility power to
the connected equipment and is still charging battery at the same time.
D. When external power source fails, the UPS will power up automatically by batteries.
The ‘YELLOW’ LED is blinking and the UPS has beep sound every 10 seconds. You
should save all your data and close all applications as soon as possible and turn off the
UPS.
E. When the battery output voltage drops to a minimum, the ‘YELLOW’ LED on the UPS
front panel is blinking while generating beeps every 1 second. You should turn off the
main switch of the UPS.
2
2.3 Front / Rear Panel Explanation
Yellow LED
ON when UPS is offline charging battery.
Blinking when AC is abnormal.
Green LED
ON when UPS is running normal.
OFF when UPS is off or abnormal.
Red LED : On only when UPS is fault
MAIN Switch : Control UPS On/Off
A. AC Inlet
B. Backup Outlets
C. AC Fuse Holder (W/fuse)
2.4 Troubleshooting
3
3. SPECIFICATIONS
Model PRO700
Capacity 650VA
Input Voltage Range 140 – 300VAC ± 5VAC
Frequency > 40 Hz
Phase Single + GND
Output Voltage Range 230VAC + 11% - 17%
Battery Mode 230VAC ± 10%
Frequency 50Hz ± 1Hz (Battery Mode)
Simulated Sine Wave (Battery Mode)
Waveform
Sine Wave (AC Mode)
Transfer Time 2ms typical
Battery Type & Number 12V8.2AH – 1pc
Backup Time 8 – 20 minutes depending on load
Recharge Time 90% Capacity after 8 hours
Protection/ Short Circuit Line mode – Fuse & software protection (CPU)
Monitoring Protection Battery mode – Software protection (CPU)
Surge Protection Yes
Alarms Audible & Visual
Over Temperature >75ºC Alarm will sound
Protection >85ºC the system will shutdown
Line Mode: 100-120% 5 minutes change to fault mode
Overload >120% change to fault mode immediately
Protection Battery Mode: 100 – 120% 5 secs shut down;
>120% shut down immediately
Intelligent Battery Prevent overcharging of battery.
management Protect battery and prolong battery life.
Interface NA
Interface 9P D-Type
NA
Connector
Software (optional) NA
General Noise <40dB
Temperature 0ºC - 40ºC
Humidity 0% - 95% relative humidity
Power Factor Up to 0.7
Built-in AVR Full AVR (3 Steps)
4
1. PERHATIAN Bahasa Indonesia
Baterei UPS sudah diisi penuh sebelum keluar dari pabrik. Selama pengiriman, kapasitas
dari isi baterei akan berkurang. Untuk memastikan efisiensi dari UPS, sebaiknya baterei
diisi kembali sebelum digunakan selama 12 jam.
Hubungkan UPS ke pusat listrik dengan menggunakan kabel 3 pin (berikut grounding).
Grounding ini sangat berguna untuk memproteksi peralatan kita dari petir.
UPS ini mempunyai baterei internal dan energi nya tidak bisa dibuang. Output dari UPS
sendiri akan mengeluarkan arus listrik walaupun UPS tidak dihubungkan langsung ke aliran
JANGAN biarkan air atau benda asing lain nya masuk kedalam UPS.
JANGAN gunakan UPS ini ke peralatan yang bukan peralatan komputer. UPS ini hanya di
rancang untuk digunakan oleh peralatan komputer saja.
Untuk mengurangi resiko panas yang berlebihan dari UPS, jangan meletakan UPS yang
langsung terkena sinar matahari atau hindari peletakaan yang dekat dengan peralatan yang
mengeluarkan panas.
1
2. PENGGUNAAN
2.1 Instruksi Penggunaan
A. Sambungkan kabel power dari UPS ke sumber listrik (PLN). Lampu ‘KUNING’ akan
menyala. Artinya UPS sedang melakukan charging ke baterai. (Note: JANGAN dulu
menggunakan UPS anda sampai baterai dari UPS anda sudah di charge selama
kurang lebih 12 jam).
B. Sambungkan komputer dan monitor anda ke output UPS. (Note: Total daya dari
komputer dan monitor harus lebih kecil dari kemampuan output daya maximum
dari UPS anda. JANGAN gunakan peralatan yang melebihi dari kemampuan UPS
anda. seperti laser printer, karena Laser printers membutuhkan daya yang sangat
besar dari peralatan komputer anda yang lainnya)
C. Nyalakan UPS dengan menekan tombol power yang ada pada panel depan. Lampu
‘HIJAU’ akan menyala dan lampu ‘KUNING’ akan padam. Artinya UPS bekerja dengan
menggunakan listrik PLN dan tetap melakukan charging ke baterai dalam waktu yang
bersamaan.
D. Ketika sumber listrik padam, UPS akan bekerja secara otomatis dengan menggunakan
baterai. Lampu ‘KUNING’ akan berkedip dan diikuti dengan suara beep di setiap 10
detik. Saat ini anda harus menyimpan seluruh data anda dan matikan UPS secara
manual.
E. Ketika output dari baterai melemah, lampu ‘KUNING’ akan terus berkedip dan diikuti
dengan suara beep disetiap detik. Anda secepatnya harus mematikan UPS secara
manual. Ini sering terjadi untuk UPS jenis tanpa software monitoring.
Mode AC, Baterai Charge Tidak ada Bunyi HIDUP MATI MATI
Mode AC, UPS Normal Tidak ada Bunyi MATI HIDUP MATI
Sumber Listrik Padam,
Bunyi beep setiap 10
dan UPS bekerja dengan Berkedip MATI MATI
detik
baterai
Bunyi beep setiap
Output Baterai melemah Berkedip MATI MATI
detik
Bunyi beep setiap 0.5
Overload pada kondisi AC MATI HIDUP MATI
detik
Overload pada kondisi Bunyi beep setiap 0.5
Berkedip MATI HIDUP
Battery detik
UPS bermasalah Bunyi beep panjang MATI MATI HIDUP
2
2.3 Penjelasan Panel Depan
Lampu KUNING
HIDUP ketika UPS sedang melakukan
Proses charging
BERKEDIP ketika sumber listrik (PLN)
padam
Lampu HIJAU
HIDUP ketika UPS bekerja normal.
MATI ketika UPS mati atau tidak normal.
Lampu MERAH
HIDUP UPS overload, atau bermasalah
MAIN Switch
Untuk mengontrol UPS HIDUP / MATI
A. AC Inlet
B. Backup Outlets
C. AC Fuse Holder (W/fuse)
2.4 Permasalahan Dan Solusi
3
3. SPECIFICATIONS
Model PRO700
Capacity 650VA
Input Voltage Range 140 – 300VAC ± 5VAC
Frequency > 40 Hz
Phase Single + GND
Output Voltage Range 230VAC + 11% - 17%
Battery Mode 230VAC ± 10%
Frequency 50Hz ± 1Hz (Battery Mode)
Simulated Sine Wave (Battery Mode)
Waveform
Sine Wave (AC Mode)
Transfer Time 2ms typical
Battery Type & Number 12V8.2AH – 1pc
Backup Time 8 – 20 minutes depending on load
Recharge Time 90% Capacity after 8 hours
Protection/ Short Circuit Line mode – Fuse & software protection (CPU)
Monitoring Protection Battery mode – Software protection (CPU)
Surge Protection Yes
Alarms Audible & Visual
Over Temperature >75ºC Alarm will sound
Protection >85ºC the system will shutdown
Line Mode: 100-120% 5 minutes change to fault mode
Overload >120% change to fault mode immediately
Protection Battery Mode: 100 – 120% 5 secs shut down;
>120% shut down immediately
Intelligent Battery Prevent overcharging of battery.
management Protect battery and prolong battery life.
Interface NA
Interface 9P D-Type
NA
Connector
Software (optional) NA
General Noise <40dB
Temperature 0ºC - 40ºC
Humidity 0% - 95% relative humidity
Power Factor Up to 0.7
Built-in AVR Full AVR (3 Steps)
4
TECHNICAL SUPPORT
FREE TECHNICAL SUPPORT HOTLINE:
OPERATING HOUR:
Singapore
FIDA INTERNATIONAL (S) PTE LTD
Blk 16 Kallang Place #06-02
Kallang Basin Industrial Estate Singapore 339156
Malaysia
FIDA SYSTEMS (M) SDN BHD
29 USJ 1/31, 47600 Subang Jaya Selangor,
Darul Ehsan, Malaysia
Indonesia
PROLiNK INDONESIA
P.Jayakarta Komplek 85 BR/AJ, Jakarta Pusat, Indonesia
support@fida.com
Register Online For Your Product Warranty
www.prolink2u.com
SINGAPORE
FIDA INTERNATIONAL (S) PTE LTD
Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapore 339156.
Tel : (65) 6357 0668 Email : support@fida.com
MALAYSIA
FIDA SYSTEMS (M) SDN BHD
29 Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan, Malaysia.
Tel : (60) 3 8024 9151 Email : support_my@fida.com
INDONESIA
PROLiNK INDONESIA
P. Jayakarta Komplek 85 BR/AJ, Jakarta Pusat - Indonesia.
Tel : (62) 21 628 3205 Email : support@prolink.co.id