The document contains a list of alarm codes, names, and descriptions for different network monitoring points. It includes alarms for timing bus faults, hardware and software inconsistencies, high temperatures disconnecting the main load, cabinet data mismatches, CPRI configuration faults, degraded TRX/RX/TX components, lost ring redundancies, reduced fan power, disconnected secondary nodes, alarm port configuration issues, antenna/receiver connectivity faults, smoke detection, cabinet door openings, signal processing faults, lost Y link communication, unlocked TX synthesizers, frequent software faults, corrupted TX power amplifier data, degraded RX loop tests, lost TS3 frames, disconnected RX cables, unlocked RX filters, unlocked TX synthesizers, and lost RX paths on
The document contains a list of alarm codes, names, and descriptions for different network monitoring points. It includes alarms for timing bus faults, hardware and software inconsistencies, high temperatures disconnecting the main load, cabinet data mismatches, CPRI configuration faults, degraded TRX/RX/TX components, lost ring redundancies, reduced fan power, disconnected secondary nodes, alarm port configuration issues, antenna/receiver connectivity faults, smoke detection, cabinet door openings, signal processing faults, lost Y link communication, unlocked TX synthesizers, frequent software faults, corrupted TX power amplifier data, degraded RX loop tests, lost TS3 frames, disconnected RX cables, unlocked RX filters, unlocked TX synthesizers, and lost RX paths on
The document contains a list of alarm codes, names, and descriptions for different network monitoring points. It includes alarms for timing bus faults, hardware and software inconsistencies, high temperatures disconnecting the main load, cabinet data mismatches, CPRI configuration faults, degraded TRX/RX/TX components, lost ring redundancies, reduced fan power, disconnected secondary nodes, alarm port configuration issues, antenna/receiver connectivity faults, smoke detection, cabinet door openings, signal processing faults, lost Y link communication, unlocked TX synthesizers, frequent software faults, corrupted TX power amplifier data, degraded RX loop tests, lost TS3 frames, disconnected RX cables, unlocked RX filters, unlocked TX synthesizers, and lost RX paths on
HW and SW Inconsistent Battery Backup Time Shorter Than Expected Operating Temperature Too High, Main Load Disconnected Cabinet Product Data Mismatch Configuration Fault of CPRI System DU Degraded Ring Redundancy Lost Fan Power Reduced Secondary node Disconnected Alarm Port Inconsistent Configuration Feeder Connectivity Fault Smoke Alarm RBS DOOR (RBS Cabinet Door Open) Signal Processing Fault Reset, DXU Link Lost Y Link Communication HW Fault Y Link Communication Lost TX Synthesizer Unlocked High Frequency of Software Fault Power Amplifier Fault RF Loop Test Fault, Degraded RX TS3 TRA Lost (TS Mode Is CS) RX Cable Disconnected RX Filter Loadfile Checksum Fault TX Synthesizer C Unlocked ALNA/TMA Fault RX Path Lost on D Receiver Side Description
The DUG has internal timing problems.
The software release does not support hardware board currently in use. An on demand or periodic battery test has indicated that the estimated remaining battery backup time is sh sufficient and the battery backup time is likely to be shorter than expected at the next AC power failure. An alarm is raised when the main load is disconnected because the PDU temperature is too high. The like The ability to keep a consistent product data view is lost and there is a mismatch between configured data There is a configuration fault of CPRI System. There is an internal fault in one or more TRXs/RXs/TXs. The ring redundancy in a ring topology CPRI chain has been lost. Traffic capacity is maintained but traffic c SCU Power connector is faulty / missing. The DUG has no contact with the secondary node. A configuration fault has been detected for one or more external alarm ports on an RRUS. The fault indicat for one or more alarm ports used by more than one RBS node. Malfunction detected in antenna system or AIR/mRRUS. The smoke detector raises this alarm when it detects smoke in the cabinet, which can be caused by a fire. This fault indicates that the cabinet door is open. When the door is closed, the alarm will cease within a mi The TRX has problems with its signal processing. Note: The TRX has internal problems with the Y link. See related fault. At least one of the radio synthesizers in the TX has failed to lock to the required frequency. Frequent software errors during execution of application software in the RUS/RRUS/AIR/mRRUS/RUG. The data stored in the TX power amplifier database, used by software for internal configuration, is corrupte The RF Loop test is used to detect problems with the TX and RX by sending dummy bursts between them The speech/data frames from the BSC to the TS are missing or corrupted. See related faults. See related fault. See related fault. See related fault. RX path lost on D receiver side of the TRX is lost. This alarm is raised if any related faults are raised on a T