Professional Documents
Culture Documents
- Press
Boot without any installed daughter
E360:
card:
Disable Scanner:
Method 1 (from Standard Menu):
- Network/Ports Æ - Press and while POR
- Network Menu Æ
E360/ - Network Setup Æ Clear NVRAM:
X20x/ C54x: Network/Ports Æ
- press and simultaneously Æ - Press and - Press + and while POR
Network Menu Æ
X264/ Press and Press and Network Setup Æ Only models - Select NVRAM Æ while POR
Clear all NVRAM:
with fax: - Select ”Reinit NVRAM” - Select “Reset PC
X36x/ while press and Cnt” Æ
while - Press + + and while
C54x/ POR POR **411 Method 2 (with Config Menu):
- Press POR
X54x simultaneously - Press and while POR
Clear system EPROM:
- Select “Factory Default” Æ
- Select “Restore Std Net” - Press + and while POR
X54x:
- Press
Clear mirror EPROM:
- Press
- Press
E34x/
Optra S/
T430/
T52x/ Restore factory defaults:
T61x - Press “Menu >”+”Select”+”Go” while
POR
T62x/ Standard Network
Invalid Engine Code Status:
T63x/ (or Network
from Standard Menu: - Press “Menu >”+”Select”+”Return” while
Option 1) Æ
C510/ Press “Select”
Press “Go” (=5) Std Network - Standard Network (or Network Option 1) Æ POR
(=3) and - Std Network Setup (or Network 1 Setup) Æ
C710/ “Return” (=4)
and “Return” Setup (or Network ___
- press and hold “Go” and press “< Menu” once Æ
___
Boot without any installed daughter
(=4) while POR 1 Setup) Æ
C720/ while POR press and hold - Select NVRAM Æ card (T62x, T63x, C91x):
“Go” and press - Select ”Reinit NVRAM” - Press “Go” while POR
C75x/ “< Menu” once
Enter Flash Font Data Mode (T61x,
C76x/ C71x, C72x, W820):
C91x/ - Press “< Menu”+”Select”+”Return” while
POR
W810/
W812/
W820
- Press
T656dne: Clear non critical NVRAM:
(Attention: Last Resort, cannot be
Method 1 (from Standard Menu): undone!)
- Network/Ports Æ - Press 6+7+8 while POR
- Standard Network (or Network 1 on dw-model)
Network/Ports Æ
T656dne/ - Std Network Setup (or Network 1 Setup) Æ Access to Config Menu with Scanner
Press the 2 Press the 3 Standard Network
Only models - press 9, 7 and 6 simultaneously Æ disabled:
X65x/ and 6 buttons and 6 buttons Æ
with fax: - Select NVRAM Æ - Press 3+7 while POR
simultaneously simultaneously Std Network ___
- Select ”Reinit NVRAM”
X73x/ for about 10s for about 10s Setup Æ
**411 Invalid Engine Code Status:
while POR while POR press 9, 7 and 6
X86x simultaneously
Method 2 (with Config Menu): - Press 3+4+6 while POR (= E+N+G)
- Press the 2 and 6 while POR
- Select “Factory Default” Æ Boot without any installed daughter
- Select “Restore Std Net” (starts directly!) card:
- Press “Go” while POR
Factory Defaults:
- Switch printer off
249x: - Open the ribbon access cover (paper
and ribbon cartridge must be installed)
- Move the printhead toward the operator
panel side of the printer until it stops.
Setup Mode: - Close the ribbon access cover.
Open the - Press and hold <Tear Off + Tractor>
24xx/ Only 25xx network printers:
operator while you turn the printer on.
___ ___ ___ Press button above the network connector with a pen tip ___
panel cover to - Continue holding these buttons until the
25xx access layer
while POR
carrier moves. The operator panel lights
two blink several times. Once the carrier
moves, your settings have been reset to
factory defaults.
Print Test:
- Press “Linefeed” while POR
25xx:
Service Menu:
Press Factory default and NVRAM Reset:
4227+ “Menu/Quit”
___ ___ ___
Press “Menu/Quit” and “Micro Up” while POR
___ ___
while POR
Disable V.34:
- Start printer in Service Mode
- Select “Fax/Scanner Diag”
- Select “Parameter” and press “OK”
- Press “System” - Use the arrow keys to change the
Service Mode:
- Select “Admin Menu” and press “OK” displayed key to 825-658 and press
Press - Select “Network Settings” and press “OK” “OK”
X560 ___ ___ ___
- Select “Initialize NVM” and press “OK”
___
- Toggle the value from 01 to 00 and
and
- Toggle to “Yes” to the question “Are you sure?” press “OK”
while POR
and press “OK” - Press Stop 3 times
- Select “Complete” and press OK to save
the values
- Press OK to exit the Parameter menu
item, the MFP will restart .
Attention: Before resetting any settings, especially network settings, the customer has to agree. Print settings before reset.
First... And then...
Double-check the Ethernet cable connection to the printer replace the cable if the condition is in doubt or the connector is broken.
Confirm a solid-status and blinking-activity light are appearing at the top left and right-hand corners of the printer ethernet replace the cable or try a different ethernet drop on the switch, router, or hub.
port NOTE: Certain networks limit network bandwidth by forcing network switch speed and duplex settings. In this case, consider forcing network connection speed on the print server.
Print a network settings page confirm Status: "Connected" and successful IP address assignment.
try communicating with the printer again.
If implementing static IP parameters, use the printer navigation buttons or keypad to reapply these values
NOTE: Invalid static IP parameters will prevent network connectivity, so make sure the IP, netmask, and gateway addresses match those of the end user's network.
If the network settings page shows "Connected" and IP parameters have been re-established, try opening the embedded
consider other communication tests such as PING, TELNET, and FTP to rule out duplicate IP addresses or other.
web server
Check the printer driver port configuration and confirm identical printer and port IP addresses. If not, recreate the port or run the wireless setup utility (WSU) if this is a wireless connection.
If possible, create a new port using MS Standard TCP/IP to rule out a problem with the Lexmark port monitor software. consider printing a document to file, and then ftp the resulting .prn file out to the printer.
Place a known working printer in the same location. Use the same network cable and ethernet drops (ports) verify that printer is communicating on the network.
If the printer is set up for queue-based printing, verify that the print server hosting the print queue is able to communicate
if the print server is able to communicate with the printer, recommend diagnosis of the client computer's print queue, user rights, permissions, or print sharing condition.
with the printer.
Consider replacement of the printer or network card option only if you have tried all of of the above suggestions if the network connectivity condition continues, note that it is most likely not due to the printer.
1. Code levels 4. Modem Settings
Config Menu 2. Agency test Menu 5. Scanner info
The Configuration Menu group contains a set of menus, settings, and operations which are infrequently required by a user. Generally, the 3. Fax Settings 9. Reboot System
options made available in this menu group are used to configure a printer for operation.
Network SE Menu
Diag Menu In this Menu you can find Network technician issues.
The Diagnostics Menu group consists of menus, settings, and operations that are used to diagnose various printer problems.
Note: While the Diagnostics Menu Group is active, all host interfaces are offline. Maintenance Menu
Maintenance mode contains information and settings that can be used in servicing the X5xx series.
Service Menu (Diagnostic Mode)
The Diagnostics Mode group contains the settings and operations used while manufacturing and servicing the MFP. When diagnostics mode Flash system code mode (also called “Invalid Engine Code State”)
is entered, one of the diagnostic menu items will display automatically. What it says. Flash the system code.
Fax SE Menu
Autor: Klaus Joerissen 27.04.2011 Page 7