Professional Documents
Culture Documents
■ II-i series
Service Manual
Copyright
© 2012 Carl Zeiss Meditec, Inc. All rights reserved.
Trademarks
Humphrey is a registered trademark of Carl Zeiss Meditec, Inc. in the
United States and/or other countries.
All other trademarks used in this document are the property of their
respective owners.
IMPORTANT NOTE
This service document contains detailed procedures and descriptions
specially compiled for Carl Zeiss service staff. For understanding the
contents and for the reliable performance of service work, it is essential
that product-specific service training be completed with Carl Zeiss Meditec,
Inc. or a training organization commissioned by Carl Zeiss Meditec, Inc.
`çåíÉåíë=
=
=
=
=
=
=
=
ec^=ffJá=ëÉêáÉë=póëíÉã==
lîÉêîáÉï=
The Humphrey Field Analyzer II-i series Model 720i, 740i, 745i and 750i
are automatic perimeters that employ standard automated perimetry
technology for measurement of the visual field of the human eye. For a
complete description of these medical devices, including intended use /
indications for use statement, please refer to the user manual.
=
^Äçìí=qÜáë=j~åì~ä=
This manual is intended for use by Field Support Engineers who have
completed Carl Zeiss Meditec service training on the Humphrey Field
Analyzer II-i.
Carl Zeiss Meditec, Inc. will make available on request circuit diagrams,
component part lists, descriptions, calibration instructions, or other
information that will assist Product-specific Trained SERVICE PERSONNEL
by Carl Zeiss Meditec, Inc. or a training organization commissioned by Carl
Zeiss Meditec, Inc. to repair those parts of the EQUIPMENT that are
designated by CZMI as repairable by SERVICE PERSONNEL.
`ä~ëëáÑáÅ~íáçå=L=`çãéäá~åÅÉ=
=
Complies with US and Canadian medical electrical system safety requirements
=
=
póëíÉã=bäÉÅíêáÅ~ä=fåÑçêã~íáçå=
=
Instrument Electrical Rating:
• 100 – 120V ~, 50/60 Hz, 4.0A
• 230V ~, 50/60 Hz, 1.8A
Fuse Rating:
Fuse Rating:
• T8A, 125V; (HFA 120)
• T6.3A, 250V; (HFA 230)
Duty Cycle:
• Int. 0.8 min/21 min (HFA 120)
• Short-Time-Op 2 min, int. 1 min 19 min (HFA 230)
p~ÑÉíó=fåÑçêã~íáçå=
WARNING: Do NOT block the ventilation openings. These allow
for the release of heat generated during operation. A buildup of
heat due to ventilation opening blockage can cause failures
which may result in a fire hazard.
póãÄçäë=~åÇ=i~ÄÉäë=
=
The following are the symbols (and their definitions) that MAY be found on
the Humphrey Field Analyzer II-i System:
WARNING: Follow instructions for use. Failure to read and follow instructions may result
in hazards that can lead to serious injury. Instructions may also describe potential serious
adverse reactions and safety hazards.
WARNING
CAUTION
CAUTION:
CAUTION: Hot Surface
Surface
Type B – Degree of protection against electric shock of applied part (chin and forehead rests).
~ Alternating Current
0I Off
Off On
Stand By
Manufacturer
Serial Number
Model Number
Fuse
=
Complies with 93/42/EEC Medical Device Directive
=
=
=
mêçíÉÅíáîÉ=m~ÅâáåÖ=fåÑçêã~íáçå=L=
póãÄçäë
The protective packing symbols specify the handling requirements of the instrument.
Handling Requirements
Keep Dry
This End Up
=
båîáêçåãÉåí~ä=péÉÅáÑáÅ~íáçåë=
Operating Conditions
Operating Temperature: +10° C to +40° C
Relative Humidity: 30% to 75% excluding condensation
Atmospheric Pressure: 700 to 1060 hPa
Max wet bulb: 78°F (26°C)
póëíÉã=cìëÉ=oÉéä~ÅÉãÉåí=
Two fuses are located in the rear of the unit.
1. Power down the system. Unplug the power cord at both ends, for
safety and easy access.
Figure 1.
Figure 2.
3. Slide out each fuse holder (marked with an arrow) and check the
filament for breakage.
Figure 3.
4. Insert the new fuse(s) in the holder(s). Slide the holders back into the
housing with white arrows pointing to the right. Push the cover up
and in until it snaps closed.
Figure 4.
mçïÉê=q~ÄäÉ=cìëÉ=oÉéä~ÅÉãÉåí=
Two fuses are located just below the table power cord inlet, near the floor.
1. Power down the table. Unplug the table power cord at both ends, for
safety and easy access.
4. Insert the new fuse in the holder. Slide the holder back into the
housing until it snaps closed.
píáãìäìë=mêçàÉÅíáçå=i~ãé=
oÉéä~ÅÉãÉåí=
Figure 7.
3. Standing in front of the bowl opening, you will find that the
projection lamp is located inside the open case top, at the
12 o’clock position.
Figure 8.
Figure 10.
Note: Do NOT touch the glass part of the lamp with your
fingers, as this will shorten the life expectancy of the lamp. If
your finger touches the glass portion of the lamp, wipe the lamp
clean with a soft cloth.
Figure 11.
Figure 12.
8. To replace the top access panel, insert the panel into the
opening. As you do so, align the lamp image on the lid with
the raised dot on the underlying case. Rotate the panel
clockwise until the lamp symbol aligns with the open-circle
symbol.
^áê=fåí~âÉ=cáäíÉê=oÉéä~ÅÉãÉåí=
Note: To ensure proper cooling of the instrument, the air filter must be
cleaned or replaced every three months (P/N 266010-0029-381).
1. Locate the air filter cover underneath the overhang on the back of the
instrument. Press firmly with your finger or thumb on the middle of
the top surface of the cover, and push down and pull out to unlatch
it. Tilt the air filter cover open on its hinges and remove the air filter
from its two locating pins.
Figure 13.
2. Clean or replace the air filter. For cleaning, you should shake the air
filter a few times and flick it with a fingertip to dislodge trapped dust.
The filter may be rinsed with water, but make sure the filter is
completely dry before Step 3. If you wish to replace the air filter, call
the Carl Zeiss Meditec Parts Department and order a “Fan Filter”
(P/N 266010-0029-381).
3. Return the clean and dry air filter to the locating pins in the air filter
cover. Close and latch the air filter cover.
=
=
=
=
=
Figure 14.
Figure 12.
=
Figure 15.
Page
Intentionally
Blank
^ÄÄêÉîá~íáçå=aÉÑáåáíáçåë=
Table 1 lists definitions for the abbreviations that appear in the following
pages.
For part numbers of individual cables, first refer to the System Interconnect
diagrams at the end of this service manual. Cables that do not have a part
number listed are supplied only as part of an associated assembly.
Note - Part numbers are not provided to parts that are NOT identified as a
“Spare Part”.
=
=
^ÅÅÉëëçêáÉë=L=pìééäáÉë=L=`çåëìã~ÄäÉë==
- sÉêëáçå=≤RKM=
P/N Description
266002-1125-235 Accessory kit (All Models)
266010-0029-954 B/Y Lamp, (for blue/yellow feature), Halogen, w/Reflector, 12V, 20W
^ÅÅÉëëçêáÉë=L=pìééäáÉë=L=`çåëìã~ÄäÉë=
- sÉêëáçå=≥RKN=
P/N Description
266002-1125-235 Accessory kit (All Models)
266002-1140-088 HFA 5.1 User Manual Hong Kong (English OUS paper copy)
pÜáééáåÖ=j~íÉêá~äë
9 --- Pallet
ec^=ffJf=jáëÅÉää~åÉçìë=Ó=N= =
ec^=ffJá=jáëÅÉää~åÉçìë=Ó=O
Page
Intentionally
Blank
m~íáÉåí=pìééçêí=^ëëÉãÄäó=
1 Belt, 370/2.03/6.0
2 Setscrew, M4 x 6, Set Soc Cup
3 Pulley, 18/2.03/5
4 Washer, Flat, Nylon, .200/.437/.020
5 Setscrew, M3 x 4, Soc Cup
6 Leadscrew and Nut, Horizontal
7 Screw, Shoulder, 5.0/4 M4 Soc HD
8 266002-1100-085 Tape Foam, 3.75 Gray, Front cover
9 Screw, M4 x 6, Soc Btn HD Cap
10 Washer, Square Cone .168/.370/.050
11 Headrest, Molded (Non-Blue/Yellow)
12 Slide, Chinrest, Horizontal
13 Spacer, Forehead Rest
14 Cover, Front
15 Stud Fastener, ¼ turn, 4mm x 24mm
16 Retainer, Stud Fastener, ¼ Turn, 4mm
17 Screw, M4 x 8, Soc HD Cap
18 Rivet, Push, Nylon
19 Screw, M4 x 20, Soc HD Cap
20 Washer, Flat, .198/.437/.062
21 Headrest, Molded (Blue/Yellow)
22 Baffle, Blue/Yellow
23 Holder, Baffle, Blue/Yellow
24 Screw, 2-56 x .188
25 Washer, Wavy, .25/.345/.008
26 Black Out Velvet Patch
`ÜáåêÉëíLqêá~ä=iÉåë=eçäÇÉê=^ëëÉãÄäó=
mêçàÉÅíáçå=^ëëÉãÄäó=
mêçàÉÅíçê=^ëëÉãÄäó=
mêçàÉÅíáçå=qìêêÉí=^ëëÉãÄäó==
_çïä=^ëëÉãÄäó=
léÉê~íçê=m~åÉä=^ëëÉãÄäó=
_Lv=i~ãé=^ëëÉãÄäó=
aêáîÉ=jçìåíáåÖ=^ëëÉãÄäó=
- sÉêëáçå=≤RKM=
aêáîÉ=jçìåíáåÖ=^ëëÉãÄäó=
- sÉêëáçå=≥RKN=
`mr=L=_~Åâéä~åÉ=båÅäçëìêÉ=
- sÉêëáçå=≤RKM=
`mr=L=_~Åâéä~åÉ=båÅäçëìêÉ==
- sÉêëáçå=≥RKN=
mçïÉê=q~ÄäÉ=L=mêáåíÉê=^ëëÉãÄäó=
rééÉê=c~å=^ëëÉãÄäó=
1 Bracket, Fan
2 Nut, M3 Lock Polyamid Insert
3 Washer, Flat #8
4 266010-0029-874 Grommet, Ribbed, .155/.370/.230/.05
5 266010-0029-774 Assy, Fan, 12V Upper
6 Guard, Fan, 80mm
7 Screw, M3 x tab Soc Hd Cap
8 Filter, Foam, Fan, 80mm
9 266002-1106-254 Retainer, Filter, Fan, 80mm
9 7
6
8
5
4
3
1
2