Professional Documents
Culture Documents
Pipe supports UN
Pipe clamps form A and form U 3790-31
Design dimensions, weights and allowable loads;
based on American Standards Page 1 of 9
Rohrhalterungen; Schellen Form A und Form U; Konstruktionsmaße,
Gewichte und zulässige Belastungen; basierend auf Amerikanische Standards
Contents
Page
1 Scope .................................................................................................................................................................... 1
2 Units, abbreviated terms ..................................................................................................................................... 1
2.1 Units....................................................................................................................................................................... 1
2.2 Abbreviated terms .................................................................................................................................................. 1
3 General information ............................................................................................................................................. 1
4 Clamps form A, DS 22 to DS 540 ........................................................................................................................ 2
4.1 Designation ............................................................................................................................................................ 6
5 Clamps form U, DS 550 to DS 2030 .................................................................................................................... 6
5.1 Designation ............................................................................................................................................................ 9
6 Materials and property classes........................................................................................................................... 9
Reference standards ........................................................................................................................................................... 9
1 Scope
This Uhde standard (UN) applies to the design and construction of industrial and chemical plants. It contains
requirements about design dimensions, weights and allowable loads of the clamps form A and form U for
uninsulated, heat-insulated and cold-insulated steel piping. American Standards with metric dimensions are
based for this pipe clamps.
Copyright reserved
3 General information
The standard part numbers refer to the materials specified in the section "Materials and property classes".
Other part numbers are required when changing the material.
UF GP-ST-01 F01 E 2012-02
FV
Plate ASTM A6/A6M
s
R
FQ FAx
E
D
S ØD 1
C A C B
Part number
MS0001A
MS0003A
Figure 1. Clamps form A
Table 2. Continued
Clamps form A, design dimensions and total weights
2 Hexagon bolt
Weight in kg/piece
ASME B18.2.3.5M with
hexagon nut
Clamp inside
ISO 4032
Outside Developed
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
Pipe supports
49 40 1½" 48.3 48.3 138 1410 4370 90 0.32
61 50 2" 60.3 60.3 164 2180 7050 106 0.62
74 73 72 184 1830 6100 120 0.69
65 2½"
77 76.1 189 1760 5920 123 0.71
3790-31
153 152 333 2020 7700 217 2.09
Page
UN
March 2018
160 154 to 162 344 1930 7460 224 2.16
169 150 6" 168.3 168.3 164 to 171 358 1830 7170 233 2.25
3
1) Weight for 2 clamp segments. without hexagon head bolts and hexagon nuts.
2) The specified loads are not equivalent to the loads for complete pipe supports (e.g. pipe shoes. tubular supports).
9 of
Table 2. Continued
2 Hexagon bolt
Weight in kg/piece
ASME B18.2.3.5M with
hexagon nut
Clamp inside
ISO 4032
Outside Developed
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
Pipe supports
209 204 to 211 421 1490 6110 274 2.64
213 12 50 427 1470 6020 5930 278 24 17.5 11 6 268 M16 50 0.13
216 214 to 216 432 1450 5950 281 2.71
220 200 8" 219.1 219.1 218 to 220 438 1420 5870 285 2.75
3790-31
340 330 to 339 644 1120 4800 415 4.85
Page
UN
March 2018
343 341 649 1110 4770 418 4.89
350 342 to 346 660 1090 4690 425 4.97
4
356 350 14" 355.6 355.6 350 to 356 669 1070 4620 431 5.04
of
1) and 2) see page 3.
9
Table 2. Continued
2 Hexagon bolt
Weight in kg/piece
ASME B18.2.3.5M with
hexagon nut
Clamp inside
ISO 4032
Outside Developed
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
Pipe supports
407 400 16" 406.4 406.4 402 to 408 772 1700 7330 498 8.48
415 410 to 411 784 1670 7210 506 8.62
419 415 to 420 791 1660 7150 510 8.69
430 422 to 426 808 1610 6990 521 8.88
3790-31
Page
UN
March 2018
5
9 of
Draft (used for KXEO-00045) March 2018
Pipe supports UN
Pipe clamps form A and form U 3790-31
Design dimensions, weights and allowable loads;
based on American Standards Page 6 of 9
4.1 Designation
For the designation of "clamp form A" clamp inside diameter DS shall be specified in addition to the part
number (refer to Example 1).
For the designation of "hexagon bolt with hexagon nut" the thread and the bolt length shall be specified in
addition to the part number (refer to Example 2).
Example 1: Clamp form A, part number MS0001A, clamp inside diameter DS = 365,
is designated as follows:
MS0001A 365
Example 2: Hexagon bolt (ASME B18.2.3.5M), part number MB0001A, thread diameter = M20,
bolts length = 55, with hexagon nut (ISO 4032), is designated as follows:
MB0001A M20 / 55
FV
Plate ASTM A6/A6M B1
L F E
FQ FAx
G
H
D
S
30 to 34
ØD 1
C A C B
Part number
MS0011A
MS0013A
Figure 2. Clamps form U
Clamps form U, design dimensions and total weights
Table 3. Continued
4 Hexagon bolt
Weight in kg/piece
ASME B18.2.3.5M with
Deve- hexagon nut
Clamp inside
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
Pipe supports
590 586 to 589 910 2200 9440 658 21.95
600 589 to 598 926 2170 9310 668 22.27
610 599 to 608 941 2130 9180 679 22.59
615 600 24" 610 610 609 to 610 949 2110 9110 684 22.75
C 130 x 13
(127 x 47)
650 639 to 646 1004 2000 8690 720 160 23.88
660 649 to 658 130 10 1020 1970 8580 16010 730 30 22 67 30 to 18 127 65 24.20 M20 200 0.61
670 659 to 666 1036 1940 8470 741 164 24.52
680 669 to 679 1051 1910 8360 751 24.84
690 688 to 689 1067 1890 8250 761 25.16
700 690 to 699 1083 1860 8150 772 25.48
716 700 28" 711 711 708 to 710 1108 1820 7990 788 25.99
720 718 to 719 1114 1810 7950 792 26.12
730 729 1130 1790 7860 802 26.44
740 730 to 739 1146 1760 7760 813 26.76
750 740 to 749 1161 1740 7670 823 27.08
3790-31
760 750 to 759 1177 1720 7580 833 27.40
Page
UN
March 2018
765 750 30” 762 762 1185 1700 7540 838 27.56
770 760 1193 1690 7500 843 27.72
7
1) Weight for 2 clamp segments. without hexagon head bolts and hexagon nuts.
2) The specified loads are not equivalent to the loads for complete pipe supports (e.g. pipe shoes. tubular supports).
9 of
Table 3. Continued
4 Hexagon bolt
Weight in kg/piece
ASME B18.2.3.5M with
Deve- hexagon nut
Clamp inside
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
Pipe supports
840 830 1303 1550 6940 915 29.96
C 130 x 13
(127 x 47)
850 840 1318 1540 6790 925 160 30.60
130 10 16010 30 22 67 30 to 18 127 65 M20 200 0.61
860 850 1334 1520 6860 935 164 30.93
880 870 1365 1480 6650 955 31.25
C 150 x 15.6
(152 x 51)
1430 1400 56" 1422 1422 2237 2450 11310 1529 180 91.83
1535 1500 60" 1524 1524 155 16 2402 2290 10580 37580 1634 35 26 85 35 to 24 152 75 98.25 M24 220 0.99
1630 1600 64" 1626 1626 2551 2160 10000 1730 184 104.05
1830 1800 72" 1829 2829 2865 1920 8970 1931 116.28
2030 2000 80" 2032 2032 3179 1730 8130 2132 128.51
1) and 2) see page 7.
3790-31
Page
UN
March 2018
8
9 of
Draft (used for KXEO-00045) March 2018
Pipe supports UN
Pipe clamps form A and form U 3790-31
Design dimensions, weights and allowable loads;
based on American Standards Page 9 of 9
5.1 Designation
For the designation of "clamp form U" clamp inside diameter DS shall be specified in addition to the part
number (refer to Example 3).
For the designation of "hexagon bolt with hexagon nut" the thread and the bolt length shall be specified in
addition the part number (refer to Example 4).
Example 3: Clamp form U, part number MS0011A, clamp inside diameter DS = 860,
is designated as follows:
MS0011A 860
Example 4: Hexagon bolt (ASME B18.2.3.5M), part number MB0001A, thread diameter = M20,
bolts length = 200, with hexagon nut (ISO 4032), is designated as follows:
MB0001A M20 / 200
Reference standards
other standards
ASME B18.2.1 : 2012 Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex
Flange, Lobed Head, and Lag Screws (Inch Series)
ASME B18.2.2 : 2015 Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange,
and Coupling Nuts (Inch Series)
ASTM A6/A6M : 2017 Rev. A Standard Specification for General Requirements for Rolled Structural Steel
Bars, Plates, Shapes, and Sheet Piling
ASTM A36/A36M : 2014 Standard Specification for Carbon Structural Steel
ASTM A193/A193M : 2017 Standard Specification for Alloy-Steel and Stainless Steel Bolting for High
Temperature or High Pressure Service and Other Special Purpose
Applications
ASTM A194/A194M : 2017 Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High
Pressure or High Temperature Service, or Both
ASTM A307 : 2014 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod
60 000 PSI Tensile Strength
ASTM A387/A387M : 2017 Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-
Molybdenum
ASTM A563 : 2015 Standard Specification for Carbon and Alloy Steel Nuts
ASME B18.2.3.5M
ISO 4032