Professional Documents
Culture Documents
in/smschannels/subscribe/JNTUHOME
om
3. A basic shaft is one whose [ ]
(A) Lower deviation is zero (B) upper deviation is zero
(C) lower & upper deviations are zero (D) None of the above
e.c
4. According to Indian standards, total number of tolerance grades are [ ]
(A) 18 (B) 12 (C) 10 (D) 8
(A) Elastic materials (B) brittle materials (C) ductile materials (D) plastic materials
8. If the tearing efficiency of a riveted joint is 75%,then the ratio of diameter of rivet to the pitch is
w
equal to [ ]
(A)0.2 (B) 0.25 (C) 0.5 (D) 0.6
w
(A)diameter of both the shafts is same (B)angle of twist of both the shafts is same
(C)material of both the shafts is same (D)twisting moment of both the shafts is same
10. The notch angle of the Izod impact test specimen is _________ in degrees [ ]
(A) 10 (B) 20 (C) 30 (D)45
Cont…..2
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
13. Transverse fillet welded joints are designed for __________________ strength
16. The diameter of the rivet hole is usually ______ the nominal diameter of the rivet
om
17. For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at
______________.
e.c
19. The railway carriage coupling have ___________ threads
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
om
3. In cyclic loading, stress concentration is more serious in [ ]
(A) Elastic materials (B) brittle materials (C) ductile materials (D) plastic materials
e.c
(A)1 in 16 (B) 1 in 32 (C) 1 in 48 (D) 1 in 100
5. If the tearing efficiency of a riveted joint is 75%,then the ratio of diameter of rivet to the pitch is
equal to
(A)0.2 (B) 0.25 (C) 0.5 (D) 0.6
m [ ]
ho
6. Two shafts will have equal strength, if [ ]
(A)diameter of both the shafts is same (B)angle of twist of both the shafts is same
tu
(C)material of both the shafts is same (D)twisting moment of both the shafts is same
7. The notch angle of the Izod impact test specimen is _________ in degrees [ ]
.jn
Cont…..2
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
13. The diameter of the rivet hole is usually ______ the nominal diameter of the rivet
14. For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at
______________.
om
17. The taper on cotter varies from_____________
e.c
18. Resilience of a material is important, when it is subjected to ______ loading
20. m
Transverse fillet welded joints are designed for __________________ strength
ho
-oOo-
tu
.jn
w
w
w
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
om
3. If the tearing efficiency of a riveted joint is 75%,then the ratio of diameter of rivet to the pitch is
equal to [ ]
(A)0.2 (B) 0.25 (C) 0.5 (D) 0.6
e.c
4. Two shafts will have equal strength, if [ ]
(A)diameter of both the shafts is same (B)angle of twist of both the shafts is same
(C)material of both the shafts is same (D)twisting moment of both the shafts is same
5.
(A) 10 (B) 20 (C) 30 (D)45
m
The notch angle of the Izod impact test specimen is _________ in degrees [ ]
ho
6. The ultimate strength of steel in tension in comparison to shear is in the ratio of [ ]
tu
Cont…..2
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
11. The diameter of the rivet hole is usually ______ the nominal diameter of the rivet
12. For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at
______________.
om
17. Yield point in fatigue loading as compared to static loading is ________________.
18. Transverse fillet welded joints are designed for __________________ strength
e.c
19. A basic hole is one whose _______________ is zero
20. m
At the neutral axis of a beam the shear stress is ____________
ho
tu
-oOo-
.jn
w
w
w
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
1. If the tearing efficiency of a riveted joint is 75%,then the ratio of diameter of rivet to the pitch is
equal to [ ]
(A)0.2 (B) 0.25 (C) 0.5 (D) 0.6
om
(C)material of both the shafts is same (D)twisting moment of both the shafts is same
3. The notch angle of the Izod impact test specimen is _________ in degrees [ ]
(A) 10 (B) 20 (C) 30 (D)45
e.c
4. The ultimate strength of steel in tension in comparison to shear is in the ratio of [ ]
(A)1:1 (B) 2:1 (C) 3:2 (D) 2:3
(A) Elastic materials (B) brittle materials (C) ductile materials (D) plastic materials
Cont…..2
www.jntuhome.com
To get updates to mobile sms ON JNTUHOME to 09870807070 or http://labs.google.co.in/smschannels/subscribe/JNTUHOME
16. Transverse fillet welded joints are designed for __________________ strength
om
17. A basic hole is one whose _______________ is zero
e.c
19. The diameter of the rivet hole is usually ______ the nominal diameter of the rivet
20. For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at
______________. m
ho
-oOo-
tu
.jn
w
w
w
www.jntuhome.com