Professional Documents
Culture Documents
(W
FOR "BUILDI
Building :
EARTHWORK
DISMANTLING, CUTTING CHASE, HOLES ETC.
BRICK WORK, CONCRETE WORK ETC.
FLOORING
ROOFING &SHEET WALLING
STRUCTURAL STEEL WORKS, GRILLS, GATES ETC.
CARPENTAR'S WORKS
BAND MOULDING, CORNICE ETC.
Roads :
EMBANKMENT WORKS
SOIL COMPACTION & STABILISATION WORKS
SOIL BORING & TESTING WORKS
BRIDGE AND CULVERT WORKS
REPAIR WORKS OF BRIDGE AND CULVERT
SOLING, EDGING & METALING
BITUMINOUS WORKS
MICELLENOUS WORK
LOADING, UNLOADING, STACKING AND CARRIAGE WORKS
SUPPLY OF DIFFERENT MATERIALS
Earth work in filling in compound, tank, low land, ditches etc. with
good earth, in layers not exceeding 150 mm. including breaking
clods and consolidating the same by ramming and dressing
complete. (Payment will be made on profile measurement before
and after the work) [ P - 5 / 5 ]
Mtr. 59.99
Sq.M. 51.88
The shutters are to be sprayed with emulsion. on both sides. All
wooden fixtures like almirahs, racks etc. are also to be throughly
sprayed with chemical emulsion.
(Payment will be made on the basis of outside measurements of
doors / vwindows).
Page 8 of 338
Sq. M. 44.22
Stripping off worn out plaster and raking out joints of walls,
celings etc. upto any height and in any floor including removing
rubbish and stacking anywhere within the compound as directed.
[ P - 25 / 10 ]
Sqm 11.60
Labour for breaking 1/2 Bricks or Full Bricks (Old / New) into
metal / Khoa / chips as per specific size and stacking the same
at site or stacking yard with due allowance of sinkage / shrinkage
as per direction of the Engineer in charge. [ P - 29 / 14 ]
Labour for laying single brick flat soling including ramming and
dressing bed to proper level and filling joints with powdered
earth. [ P - 33 / 2 ] Sqm 25.18
a) Pakur Variety
I) Without approved concrete pump Cum 5,643.88
Ii) With approved concrete pump Cum 5,881.63
P-61 / 11 (a) Add extra over the rate of ground floor for basement & each
additional floor above ground floor fot items 4 to 14 :
(i) upto and inclusive of 4th floor Cum 58.88
(ii) for height above 4th floor Cum 71.44
(iii) For thin concrete members upto a thickness of 65 mm
involving shuttering and scaffolding rate of concrete enhanced
by 150% of rate by volume (Cost of shuttering & reinforcement
excluded)
(d) Extra for works beyond the roof of ground floor per
additional floor.
(i) upto and inclusive 4th (per floor) and in basement. Sqm 11.15
(ii) above 4th floor (per floor) Sqm 13.64
(e) Extra for staging beyond 4 m. in any floor Cum 53.89
(Mode of measurement : Area in plan X mean height of
staging upto soffit of shuttering above initial 4 m.)
(f) 25mm. to 30mm. shuttering without staging in foundation
etc. Sqm 167.10
Page 17 of 338
(a) Hire and labour charges for shuttering for concrete work in
overhead R.C. Reservoir on seperate R.C. frame including
fitting, fixing and striking off after completion of work including
staging upto 4 metre. [ P - 63 / 13 ]
Sqm 682.78
(Not applicable for resting on roof top.)
(b) Extra for staging beyond 4 m. [Mode of measurement : Area
of unsupported horizontal projection (where staging beyond 4 m.
is practically un-avoidable) X mean height of staging] above
initial 4 m.
Cum 147.00
Hire and labour charges for shuttering with hard wood for
precast R.C. slab, curved or straight and striking out the same
including fitting, fixing the precast slab in position with necessary
carriage and haulage, hosting etc. complete in all respect.
[ P - 65 /14 ]
Sqm 71.66
(Only the area in contact with concrete to be measured).
Brick work with 1st class bricks in lime and surki mortar (1:2) (1
lime putty / paste:2 surki), lime to be slaked at site and the
mortar to be prepared with such lime putty and first class surki
made from kiln burnt bricks having its fineness modulus between
2 and 2.5 and which passes through B.S. sieve No.8 which
corresponds to I.S. sieve No.200 with considerable grinding and
pugging it complete. [ P - 67 / 19 ]
Brick work with 1st class bricks in lime and surki mortar (1:3) (1
lime putty / paste:3 surki), lime to be slaked at site and the
mortar to be prepared with such lime putty and first class surki
made from kiln burnt bricks having its fineness modulus between
2 and 2.5 and which passes through B.S. sieve No.8 which
corresponds to I.S. sieve No.200 with considerable grinding and
pugging it complete. [ P - 69 / 20 ]
Brick work with 1st class bricks in composite mortar with sand,
lime and cement (6:1:1) (6 sand:1 lime putty/paste:1 cement)
[ P - 71 / 23 ]
Brick work with 1st class bricks in composite mortar with sand,
lime and cement (9:2:1) (9 sand:2 lime putty/paste:1 cement)
[ P - 71 / 24 ]
(a) In foundation and plinth Cum 4,235.35
(b) In superstructure, ground floor Cum 4,383.45
NOTE : 633 kg of unslaked lime @1 cu.m. of lime putty/paste.
Extra labour for brick for string course and set square brick
work,brackets and similar other projection (brick works to be paid
in respective item) [ P - 71 / 25 ] Cum 157.76
Page 19 of 338
Add extra for basement and each additional floor over the rate
for ground floor on item Nos. 23 to 30 except 29. [ P - 71 / 27 ]
(a) Upto 4th floor Cum 66.99
(b) Above 4th floor Cum 80.33
125 mm. thick brick work with 1st class bricks in cement mortar
(4:1) in ground floor. [ P - 73 / 29 ] Sqm 558.94
125 mm. thick brick work with 1st class bricks in cement mortar
(3:1) in ground floor. [ P - 73 / 30 ]
Sqm 592.27
Extra for using approved H.B netting in every third layer in 33 &
34 above in any floor [ P - 73 / 31 ]
Sqm 37.72
(a) 100 mm. thick brick work with 1st class Modular bricks set in
sand cement mortar (4:1) including raking out joints, curing,
scaffolding etc. complete in all respect in ground floor.
[ P - 73 / 32 ]
Sqm 436.52
(b) 100 mm. thick brick work with 1st class Modular bricks set in
sand cement mortar (4:1) including raking out joints, curing,
scaffolding etc. complete in all respect with H.B. netting in every
third layer in ground floor.
Sqm 458.43
(a) 100 mm. thick brick work with special class Modular bricks
set in sand cement mortar (4:1) including raking out joints,
curing, scaffolding etc. complete in all respect in ground floor.
[ P - 73 / 33 ]
Sqm 460.63
(b) 100 mm. thick brick work with special class Modular bricks
set in sand cement mortar(4:1) including raking out joints, curing,
sacffolding etc. complete in all respect with H.B. netting in every
third layer of ground floor.
Sqm 482.54
(a) 75 mm. thick brick work with 1st class bricks set in sand,
cement mortar (4:1) in ground floor including H.B. netting in
every alternate layers. [ P - 75 / 34 ]
Sqm 383.27
Page 20 of 338
(b) 75 mm. thick brick work with 1st class bricks set in sand
cement mortar (3:1) in ground floor including H.B. netting in
every alternate layer. [ P - 75 / 34 ] Sqm 433.08
Jaffri brick work 125 mm. thick with 1st class bricks in cement
mortar (4:1) including 12 mm. thick cement plaster (4:1) in all
faces in ground floor. [ P - 75 / 35 ]
Sqm 554.66
200 mm. thick Brick work with Fly Ash Bricks set in sand cement
mortar (6:1) including raking out joints, curing, scaffolding etc.
complete in all respect. [ P - 75 / 36 ]
100 mm. thick brick work with Fly Ash Bricks set in sand cement
mortar (4:1) including raking out joints, curing, scaffolding etc.
complete in all respect. [ P - 75 / 37 ]
Bonding new brick work with old at every 4th course including
Sqm of
cutting chase and mending damages in cement mortar (4:1) and
bonded
curing. [ P - 77 / 41 ]
area 177.54
Add extra for each additional floor over the rate for ground floor
on items from [ P - 77 / 42 ]
(i) 29 to 35 except 31
(a) upto 4th floor Sqm 7.14
(b) above 4th floor Sqm 8.03
Page 21 of 338
1st class brick work of width 200 mm. with non-modular bricks in
cement sand mortar (1:6) as per technique explained in
specification and drawings. [ P - 79 / 44 ]
(a) In foundation and plinth Cum 4,139.36
(b) In superstructure ground floor Cum 4,265.46
1st class brick work of width 200 mm. with non-modular bricks in
lime and surki mortar (1:3) (1 lime putty/paste : 3 surki) as per
technique explained in the specification and drawings.
[ P - 79 / 46 ]
Add extra for each additional floor over the rate for ground floor
on items 44,45,46 above. [ P - 79 / 47 ]
FLOORING
W.C.II
Terraceed flooring of lime concrete with stone lime, surki and
32mm down jhama khoa, (7:2:1½) (7 jhama khoa:2 surki : 1½
lime putty). [ P - 91 / 1 ]
(a) 75 mm. thick Sqm 346.59
(b) 100 mm. thick Sqm 457.19
NOTE : 633 kg. unslaked lime @ 1 cu.m. of lime putty / paste.
Page 24 of 338
In ground floor.
3 mm. thick topping (High polishing grinding on this item is not
permitted) with ordinary cement.
(Add extra @1.5% for each additional floor, upto 4th. floor and
@1.75% for each addl. Floor above 4th. floor)
(FOOT NOTE : White cement for item No.6 to be supplied by the
contractor including cost thereof & grey cement will be supplied
by the Deptt.at the issue rate)
In ground floor.
(A) 9 mm. thick terazo topping, laying and finished to 6 mm. thick
after final grinding with 0 to 7 mm. size mosaic chips.
Page 25 of 338
(Add extra @1.5% for each additional floor, upto 4th. floor and
@1.75% for each addl. Floor above 4th. floor)
In ground floor.
(A) 9 mm. thick terrazo topping, laying and finished to 6 mm.
thick after final grinding with 0 to 7 mm. size mosaic chips.
(i) In ordinary grey colour Sqm 672.84
(ii) In black colour Sqm 727.66
(iii) In red colour Sqm 748.13
(iv) In silver grey (ordinary cement and white cement to be
used in equal proportion) Sqm 745.59
(v) In pink, cream, yellow, light green colour using white
cement only and necessary pigment. Sqm 900.90
(B) 12 mm. thick terrazo topping,laying and finished to 9 mm.
thick after final grinding with 0 to 10 mm. size mosaic chips.
(i) In ordinary grey colour Sqm 693.79
(ii) In black colour Sqm 753.84
(iii) In red colour Sqm 774.30
(iv) In silver grey (ordinary cement and white cement to be
used in equal proportion) Sqm 756.07
(v) In pink, cream, yellow, light green colour using white
cement only and necessary pigment. Sqm 914.09
Supplying dividing strip fitted and fixed with cement mortar (3:1)
in mosaic or patent stone floor, dado etc. complete as per
direction of the Engineer-in-charge. [ P - 97 / 10 ]
25mm. thick damp proof course with cement concrete with stone
chips (3:1.5:1) [with graded stone aggregate 10mm nominal
size]and admixture of water proofing compound as per
manufacturer's specification followed by two coat of polymer
based paint, (1st.coat after 4 to 5 days of cocrete laying and
2nd. coat just before brick masonry work) as directed (cost of
water proofing compound & polymer based paint to be paid
separately). (chequering not required over concrete or
painted surface) [ P - 99 / 11 ]
Sqm 165.82
[ Note:- Water proofing as per item No-60, polymer based paint
as per item 59(a) of Section ( c).
(i) Area of each Slab / tile upto 0.3 sq.m. Sqm 1,411.75
(ii) Area of each Slab / tile exceeding 0.3 sq.m. but not
exceeding 0.6 sq.m. Sqm 1,642.28
Page 29 of 338
(iii) Area of each Slab / tile exceeding 0.60 sq.m but not
exceeding 1.00 sq.m. Sqm 1,988.69
(iv) Area of each Slab / tile exceeding 1.00 sq.m (This item
to be executed on specific permission of Superintending
Engineer)
Sqm 2,299.10
(b) With Chawk Dungri
(i) Area of each tile upto 0.3 sq.m. Sqm 1,614.95
(ii) Area of each tile exceeding 0.3 sq.m. but not exceeding
0.6 sq.m. Sqm 1,820.26
(iii) Area of each tile exceeding 0.6 sq.m but not excedding
1.00 sq.m. Sqm 1,969.59
(iv) Area of each Slab / tile exceeding 1.00 sq.m (This item
to be executed on specific permission of Superintending
Engineer) Sqm 4,283.24
Red variety
(i) 25 mm. thick Sqm 464.72
(ii) 30 mm. thick Sqm 497.39
Supplying, fitting & fixing 1st quality Ceramic tiles in walls and
floors to match with the existing work & 4 nos. of key stones
(10mm) fixed with araldite at the back of each tile & finishing the
joints with white cement mixed with colouring oxide of required to
match colour of tiles including roughening of concrete surface, if
necessary or by synthetic adhesive & grout materials etc.
[ P - 111 / 30 ]
[A] Floor :-
With Sand Cement Morter (1:4) 20 mm thick & 2 mm thick
cement slurry at back side of tiles using cement @ 2.91 kg/Sq.m
& joint filling using white cement slurry @ 0.20 kg/Sq.m.
(a) Area of each tile upto 0.09 sq.m.
iii) Coloured decorative Sqm 711.71
ii) Other than Coloured decorative including white Sqm 661.71
[B] Wall :-
With Sand Cement Morter (1:3) 15 mm thick & 2 mm thick
cement slurry at back side of tiles using cement @ 2.91 kg/Sq.m
& joint filling using white cement slurry @ 0.20 kg/Sq.m.
[C] Floor :-
With polymerised Adhesive and Epoxy grout pointing including
spacer-2 mm (when Tiles are laid over existing hard ready
surface)
(a) Area of each tile upto 0.09 sq.m. [using adhesive 3mm th.]
iii) Coloured decorative Sqm 819.47
Page 31 of 338
(a) Area of each tile above 0.09 sq.m. [using adhesive 4.5 mm
th.]
iii) Coloured decorative Sqm 862.25
ii) Other than Coloured decorative including white Sqm 827.36
[B] Wall :-
With polymerised Adhesive and Epoxy grout pointing including
spacer-2 mm (when Tiles are laid over existing hard ready
surface)
(a) Area of each tile upto 0.09 sq.m. [using adhesive 3mm th.]
iii) Coloured decorative Sqm 844.47
ii) Other than Coloured decorative including white Sqm 794.48
(a) Area of each tile above 0.09 sq.m. [using adhesive 4.5 mm
th.]
iii) Coloured decorative Sqm 1,077.23
ii) Other than Coloured decorative including white Sqm 1,002.23
Washing and cleaning with soap water and rubbing with oil cloth
in all types of floor and dado. [ P - 119 / 36 ] Sqm 4.40
Labour for setting Qota / Dungri stone slabs in lime morter (2:1)
including necessary underlay of morter (2:1). [ P - 119 / 37 ] Sqm 170.87
Supplying, fitting & fixing Black Stone slab used in kitchen slab,
alcove, wardrobe etc. laid and jointed with necessary adhesive
cement morter (1:2) including grinding and polishing all complete
as per direction of Engineering - in - Charge in Ground Floor.
[ P - 119 / 38 ]
(For item 1 add extra for each addl. floor over the rate @1.5%
upto 4th floor and @1.75% above 4th floor.)
Roof of one storied structure (Payment to be made on surface
area of terracing including ghoondies.)
Labour for painting roof surface with Bitumen (using 135 kg(av)x
per % sq.m.)including cleaning roof, heating asphalt as directed
and spreading sand and complete including cost of sand @0.6
cu.m. per % sq.m. and cost of carriage of Bitumen from deptt
godown but excluding the cost of bitumen. (If heating is not
reqd. than deduct Rs. 3.45/- per Sq.m) [ P - 125 / 7 ]
Sqm 17.67
Cow dung (green and not dry hard) and cement wash (3 cow
dung: 1 cement by wt.) not less than 1.5 mm. thick.
[ P - 125 / 8 ]
Sqm 12.03
[Mode of payment for wooden beam (raplacing the old one) will
be made against Item No. 4 of carpanter's work]
Renewing (in job work) Ranigunge pattern tile of 1st class quality
including pointing joints with [ P - 127 / 17 ]
(i) In roof:
a) With 0.60 mm. thick sheet Sqm 533.64
b) With 0.63 mm. thick sheet Sqm 555.95
c) With 0.80 mm. thick sheet Sqm 681.63
(ii) In wall:
a) With 0.60 mm. thick sheet Sqm 525.31
b) With 0.63 mm. thick sheet Sqm 547.62
c) With 0.80 mm. thick sheet Sqm 672.56
(A) Galvanised iron sheets valley gutter with perimeter not lass
than 750 mm. with 225 mm. lap each way fitted and fixed with
necessary bolts, nuts, screws, etc.complete. Valley gutter made
of 0.63 mm. thick sheets. (300 mm End lapping) [ P - 135 / 32 ]
Metre 447.58
Asbestos plain sheet walling with teak wood beads but excluding
frame. [ P - 174 / 44 ]
(a) 6 mm. thick Sqm 270.00
(b) 4 mm. thick Sqm 206.00
Labour for curving C.I. or G.C.I. sheet for curved roof etc.
[ P - 137 / 36 ] Sqm 15.25
(Payment to be made on area of finished works done with the
curved sheets.)
Walling or roofing fitted and fixed complete with cut drum sheets
including the cost of drums, cost of cutting drums and flattening
the sheets and cost ofnecessary nails and screws.
[ P - 139 / 39 ]
Sqm 194.09
(Cost of empty bitumen drums issued by the Deptt. will be
recovered at Rs. 100.00 for each drum.)
Taking out wind-tie from roof including cutting out rusted bolts,
nuts etc. and removing materials to any distance within the
compound and stacking. [ P - 139 / 41 ]
Metre 9.40
Supplying and laying true to line and level 20 mm/ 25 mm. thick
precast roof tiles made of cement conc. with stone chips as per
approved strength and density set in 25 mm. (Ave) thick cement
mortar (1:3) and filling up joint (3 mm. wide) with cement mortar
(1:1) applying cement slurry @ 1.75 kg per sq.m. back of tiles
and then settting close the precast tiles, finishing up the joints
with slurry already laid and finally finishing the top surface
including providing 150 mm. high skirting with the same tiles
flushed with the inside surface of parapet wall,finishing the
mouth of rain water pipes curving etc. as necessary complete as
per direction of the Engineer-in-charge. (Levelling if necessary
may be paid separately) [ P - 141 / 44 ]
(a) For 20 mm. thick precast tiles (cement 14.6 kg/Sq.m for
underlayer)
Sqm 389.98
(b) For 25 mm. thick precast tiles (cement 14.6 kg/Sq.m for
underlayer) Sqm 431.39
(Add extra @ 1.5% for each additional floor upto 4th. floor and
@ 1.75% for each additional floor above 4th floor
(Add extra @1% for each additional floor upto 4th floor. @1.25%
for each additional floor above 4th floor).
Page 42 of 338
M.S. round or square bar grating of windos etc. fitted and fixed
in holes of window frme and with intermediate flat bar
stiffner( with necessary holes for the grating bars and with the
ends turned and fixed to timber frame with necessary screws)
complete , as directed. [ P-153 / 8 ]
(MODE OF MEASUREMENT):-
The weight of grillwil be detarmined by taking the physical weight
of fabricated grill and dividing the same by covered area of the
same.
N.B. No shop priming will be allowed to facilitate inspection of
workmanship. Weight of grill is to be taken after final grinding
and finishing the weld.
(b) Extra for work in grill gate.
(I) For hanging and locking arrangements including supply of
materials and labour complete. Sq. m. 0.00
(15% extra over the corresponding item of grill )
(ii) For supplying fitting and fixing bottom rollers including all
labour complete. Sq. m. 0.00
(5% extra over the corresponding item of grill )
Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both
faces of M.S./ W.I. Gate etc. with point welding at note more
than 150mm apart complete in all respect as per design
including cost of all labour and materials . [ P-157 / 12 ]
Sq.m. 1,002.28
(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25%
for each addl. floor above 4th floor)
In ground floor. Sq.m. 2,924.51
(a) Supplying fitting and fixing steel rolling shutter profile type
with 18 B.G . Of approved type steel latche section 75mm wide,
fitted with coil wire spring to necessiate the fitting of required
Nos. of C.I. Pulleys on heavy type solid drawn seamless steel
tube complete with locking arrangements both inside and
outside specially builtup side guide channels including providing
a hood for the steel rolling shutter in the room, painting two coats
of approved aluminium paint over a coat of red lead primer
complete. [ P-159 / 16 ]
Sq.m. 2,876.31
1). (Measurement will be made on the area of opening covered
by the rolling shutter corrected upto 2 decimal.)
2). Payment of painting to be separately.
(b) Supplying fitting and fixing steel rolling grills link type, shutter
with 18 B.G .of approved type steel to the section 75mm wide,
fitted with coil wire spring to necessiate the fitting of required
Nos. of C.I. Pulleys on heavy type solid drawn seamless steel
tube complete with locking arrangements both inside and
outside specially builtup side guide channels including providing
a hood for the steel rolling shutter in the room, painting two coats
of approved aluminium paint over a coat of red lead primer
complete. [ P-161 / 16 ]
Sq.m. 3,739.02
(Measurement will be made on the area of opening covered by
the rolling shutter corrected upto 2 decimal.)
Renewing bottom rail or top runners of collapsible gate including
mending good all damages. [ P-161 / 17 ] Kg. 72.64
(iii) 25 mm dia.
(iv) 32 mm dia:
(i) 10 to 16 mm dia:
Repairing steel shutter with new rivets including taking out and
refixing, adjusting, welding, cleaning cutting holes, mending
good damage to match with the existing one. [ P-165 / 23 ] Sq.M. 325.04
Page 45 of 338
( Add extra @ 1.2 % for each additional floors upto 4th floor and
@ 1.5% for each addl. Frool above 4th floor.)
In Ground floor
Flash butt welded windows and ventilators
(no shop priming will be allowed to facilitate inspection of
workmanship)
Without integrated grills.
Page 46 of 338
(ii) Top hung side hung ventilators as per I.S. sizes 580 mm. Sq,. M. 174.00
(iii)Centre hung ventilators as per I.S. sizes 580 mm. Sq,. M. 314.00
(iv) Two point nose steel handle including fitting and fixing. Each 27.00
(v) Two point nose aluminium handle including fitting and fixing. Each 29.00
(vi) steel peg stay 300 mm long including fitting and fixing. Each 20.00
(vii) Aluminium peg stay 300 mm long including fitting and fixing.
Each 30.00
Renewing seam pipe for rolling shutter as per existing size and
shape fitting, fizing complete. [ P - 173 / 39 ] Mtr. 177.76
Page 47 of 338
Renewing side slit pin for seam pipe for rolling shutter.
[ P - 173 / 40 ] Each 18.18
Labour for taking out steel door and window frame for repairs
and re-fixing the same ( or replacement by new one) including
mending good damages and supplying a protective coat of paint.
[ P - 175 / 47 ]
Supplying, fitting and fixing cast iron heavy type spiral staircase
of approve design with 50 mm.dia. Stem and C.I. Steps 150 mm.
As per design 900 mm. High C.I, railing including necessary
M.S. tie of suitable section embaded ti wall with cement concrete
(4:2:1) including cost of intermediate C.I. platform secured with
necessary tie to stem and wall with cement concrete ( 6: 3:1)
complete in all respect with all labour and materials.
[ P - 175 / 48 ]
CARPENTAR'S WORKS
W.C.II
NOTE: (1) Without the specific permission of the Superintending
Engineer no work involving teak wood should be carried out.
Page 48 of 338
Wood work in door and window frame fitted and fixed complete
icluding a protective coat of painting at the contact surface of the
frame excluding cost of concrete, Iron butt Hinges amd
M.S.clamp. [ P -179 / 1 ]
(f) Sishu, Gamar, Champ, Badam, Bhola, Morga, Hallak. Cu.M. 65,779.00
(A) Supplying fitting and fixing door frame with M.S. angle as per
drawing & direction of required section. Butt hinges will have to
be supplied as necessary & the holes for counter sunk machine
screw & nuts will be such as to fit 8 to 10mm. Iron screw. The
counter sunk nut to be welded and such screws and nuts are to
be supplied by the contractor. The nuts are to be welded after
careful checking with screw.All welding spots should be properly
filed or rounded smooth including cost of welding hinges for
hinge cleats including supplying the same & also lugs for hasp
bolt, socket bolt etc. and necessary M.S. clamps of 25mm. x
6mm. flat 225mm. long as per direction welded to the frame
icluding supplying & fixing clamps with cement concrete 4:2:1
complete. [ P - 181 / 1(A) ]
Kg. 75.51
Extra rate for Curved wood works in doors and window frame
fitted and fixed complete over corresponding items of item No- 1.
(in measuring such average length and average breadth to be
taken into consideration, depth remaining constant).
[ P - 181 / 2 ]
Cu.M. 10%
(The quantum should be corrected upto three decimals)
Note:- Extra for Lifting Charge:- i) upto 4th. Fl.Rs. 200/- M3.
ii) Above 4th. Floor Rs. 250/- per M3.
(f) Sishu, Gamar, Champ, Badam, Bhola, Morga, Hallak. Cu.M. 75,144.31
Note:- Extra for Lifting Charge:- i) upto 4th. Fl.Rs. 200/- M3.
ii) Above 4th. Floor Rs. 250/- per M3.
(d) Door and window frames fitted and fixed complete. Cu.M. 2,958.19
Page 50 of 338
(e) Post, post plates, rafters, battens, truss members, purlins etc.
(excluding cost of bolts only but including cost of nails, screws
etc. as directed. Cu.M. 3,530.00
(f) Extra over (a) or (b) for hoisting and fitting, fixing beam in
position. (Daamage if any will be repaired separetly) Cu.M. 1,963.33
(f) Sishu, Gamar, Champ, Badam, Bhola, Morga, Hallak. Sq.M. 1,115.00
M.S. sash bar upto 1200mm. Length with coach screws and flat
iron clamps 40mm. X 5mm. Fitted and fixed complete. [
P - 187 / 11 ]
Renewing M.S. clamps 40mm. X 5mm. Only for sash bar fitted
and fixed complete. [ P - 189 / 13 ] Each 23.80
Refixing sash bar with new coach screws. [ P - 189 / 14 ] Each 13.45
Supplying, fitting and fixing M.S. clamp for fixing door and
window frame made of flat bent bar, end bifurcated, fixed in
cement concrete with stone chips (4:2:1) fitted and fixed
complete as per direction. [ P - 189 / 18 ]
Renewing M.S. clamp for fixing door and window frames made
of flat bent bar, end bifurcated with necessary screws etc. in
cement concrete (4:2:1) including cutting brick work / concrete
work as per direction. [ P - 191 / 19 ]
Iron butt hinges of approved quality fitted and fixed with steel
screws, with ISI mark. [ P - 191 / 20 ]
Taking out old brass higes and fitting, fixing the same with new
brass scews. [ P - 193 / 22 ]
Taking out old iron higes and fitting, fixing the same with new
steel screws. [ P - 195 / 23 ]
Iron pad bolt (lock) of approved quality rod and handle single
cast: [ P - 199 / 28 ]
(i) 115mm x 10mm dia rod 65mm x 3mm plate. Each 85.95
(ii) 200mm x 16mm dia rod 105mm x 3mm plate. Each 115.65
Iron gravity hinge (block patent best quality) fitted and fixed
complete. [ P - 199 / 30 ] Each 112.46
(a) Supplying 'Godrej' mortice lock with latch and keys 6 levers,
including fitting and fixing complete. [ P - 203 / 36 ] Each 1,097.67
(b) Supplying 'Godrej' mortice lock with latch & keys 7 levers
including fitting and fixing complete. Each 1,407.04
(c) Supplying 'Godrej' night lock with keys 7 levers including
fitting & fixing complete. Each 1,668.81
Cord for fan light fitted & fixed complete. [ P - 203 / 37 ] Each 23.21
Renewing hinged cleat (sal) with old hinge and new screws.
[ P - 205 / 45 ]
(i) With Sal : Siliguri. Each 37.26
ii) With Sal : Malayasian. Each 30.28
(iii) With Sal : Local. Each 28.38
Supplying, fitting and fixing door made with IRC febric mesh of
75 mm x 50 mm x 4.5 mm x 2.7 mm on 50mm x 50mm x 6mm
angle iron frames all round and one 37.5mm x 6mm M.S. flat bar
over the netting all round welded to angle iron frame and
providing locking arrangements if necessary and with two coats
of synthetic enamel paint (Other than Hi-gloss ) fitted and fixed
with clamps or haskal doomney etc. complete including flat
stiffeners on every 1 metre apart both ways. [ P - 209 / 56(a) ]
Sq.m. 1,800.23
(Cost of cement concrete will be paid separately)
Page 58 of 338
(A) Iron door ring of approved quality fitted and fixed with nut
and washer complete. [ P - 209 / 59 ]
(B) Split shank iron door ring fitted and fixed complete
(I) 50 mm dia. Each 30.41
(Ii) 75 mm dia. Each 43.80
(i) 150mm plate x 10mm dia rod x 12mm hexagonal/fluted. Each 90.85
(iii) 175mm plate x 12mm dia rod x 60mm hexagonal/fluted. Each 104.24
Supplying fitting and fixing Godrej ultra vertibold brass rim lock.
[ P - 217 / 71 ] Each 1,811.60
Labour for taking out door and window frame with or without
horns and including shutter for repair replacement of different
parts of the frame and refixing the same including mending good
all damaes complete. [ P - 217 / 72 ]
Taking out door and window shutters and rehanging the same
with old fittings. [ P - 219 / 74 ]
(a) With new iron screws. Sq.M. 53.60
(b) With old screws. Sq.M. 41.82
In ground floor.
(In case of non-supply of single plank, penal rate of reduction of
20% will be made)
(i) 50mm. Thick shutters with 25mm. Thick panel.
(a) 1st class best Indian teak. Sq.M. 7970.08
(b) Ordinary teak wood Sq.M. 6015.51
(b) Sisu, Gamari, Champ, Badam, Bhola, Mogra, Hallak. Sq.M. 1835.06
(c) Other Local wood. Sq.M. 1166.09
In ground floor:
Add extra over the rate of ground floor for each addl. Floor.
[ P - 229 / 86 ]
(i) Upto 4th floor. Sq.M. 17.85
(ii) Above 4th floor. Sq.M. 22.31
[ P - 245 Providing and fixing of false celling with power coated exposed
/ 95 ] G.I. grad suspension system (E-Grid T 2430/1510 or equivalent
load carring capacity with mid span deflection not exceding
1/360 span with hanger spacing of 1200 mm c/c ) consisting of
Main Runner 3600 mm long, cross Tee 1200 mm / 600 mm long
and wall Angle. The wall angle shall be fixed on PVC Dash
Fasteners on the perimeter of the wall by steel screws with
distance 300mm c/c. The main runners to be placed @ 1200mm.
The cross Tee 1200 mm will be inserted in the pre-cut slots of
main runner at regular interval of 600 mm to form a modular grid
of 1200 mm x 600 mm. Additional cross tees of 600 mm shall be
placed perpendicular to the cross tee 1200 mm long to finally
form a grid of 600 mm x 600 mm. Grid of module size 600 mm x
600 mm shall be supported by 6 mm dia G.I. wire from purlins /
soffit. 4 mm th.High pressure steam cured non Asbestors Fibre
Cement standard ceilling board (Density > 1300 kg/m3) of size
595 mm x 595 mm, conforming IS 14862 & Type B category III of
ISO 8336, tested as per AS-1530 part 3 & BS-476 part 4,5,6,7 &
8, should be placed in the Grid module to form a Faise Ceilling.
All complete as per the drawing & direction of E.I.C. [ P - 245 /
95 ]
a) False Celling (with 4 mm thick Fibre Cement Standard Celling
Board and E-Grid T - 2430/1510). Sq.M. 545.42
[ P - 247 (A) Providing and fixing of false celling with power coated
/ 96(a) ] exposed G.I. grad suspension system (E-Grid T 2430/1510 or
equivalent load carring capacity with mid span deflection not
exceding 1/360 span with hanger spacing of 1200 mm c/c )
consisting of Main Runner 3600 mm long, cross Tee 1200 mm /
600 mm long and wall Angle. The wall angle shall be fixed on
PVC Dash Fasteners on the perimeter of the wall by steel
screws with distance 300mm c/c. The main runners to be placed
@ 1200mm. The cross Tee 1200 mm will be inserted in the pre-
cut slots of main runner at regular interval of 600 mm to form a
modular grid of 1200 mm x 600 mm. Additional cross tees of 600
mm shall be placed perpendicular to the cross tee 1200 mm long
to finally form a grid of 600 mm x 600 mm. Grid of module size
600 mm x 600 mm shall be supported by 6 mm dia G.I. wire from
purlins / soffit. 4 mm th.High pressure steam cured non
Asbestors Fibre Cement standard ceilling board (Density > 1300
kg/m3) of size 595 mm x 595 mm, conforming IS 14862 & Type
B category III of ISO 8336, tested as per AS-1530 part 3 & BS-
476 part 4,5,6,7 & 8, should be placed in the Grid module to
form a Faise Ceilling. All complete as per the drawing & direction
of E.I.C. [ P - 247 / 96(a) ]
Sectoin specification :-
Perimeter Channel :- 30mm x 20mm x 27mm, thickness 0.55mm
(min).
Intermidiate Channel :- 15mm x 45mm, thickness 0.90 mm (min).
[P- Extra over item No. 101 and 102 for providing:
259 /
103 ]
(a) Vision aperture (round or retangular in shape) with 7.4kg. Per
sq.m./3mm thick glass pane with wooden beads. (cost of glass
panes and wooden beads will be paid separately).
Each 21.12
Sq.M. of
(b) Rabeet cutting in shutters Shutters 28.42
Sq.M. of
(c) Double lef shutters Shutters 18.94
(For upper floors refer to item 128 also)
Supplying, fitting and fixing Fly / Mosquite proof nylon net on any
type of window, door shutter / frame with necessary fixing
arrangements complete. [ P - 261 / 104 ] Sq.M. 930.12
Ceiling with 12mm thick wooden planks fitted and fixed complete
(excluding the supporting framework) as per direction of the
Engineer-in-charge. [ P - 261 / 105 ]
In Ground Floor.
(a) Ordinary teak. Sq.M. 1,553.37
(b) Sishu / Champ / Badam / Gamar / Bhola / Morga / Hallak Sq.M. 849.82
(For upper floors refer to item 128 also)
In Ground Floor.
(A) Plain : Conforming to IS: 3087 - 1985
a) Exterior grade
In Ground Floor.
(i) 4mm Sq.M. 909.01
(ii) 6mm Sq.M. 1,002.72
(iii) 9mm Sq.M. 1,177.63
(iv) 12mm Sq.M. 1,420.01
(v) 16mm Sq.M. 1,970.06
(vi) 19mm Sq.M. 2,158.72
In Ground Floor.
(i) 4mm Sq.M. 665.39
(ii) 6mm Sq.M. 831.55
(iii) 9mm Sq.M. 950.24
(iv) 12mm Sq.M. 1,165.14
(v) 16mm Sq.M. 1,526.53
(vi) 19mm Sq.M. 1,800.15
Page 72 of 338
In Ground Floor.
(i) 16mm Sq.M. 1,784.58
(ii) 19mm Sq.M. 1,986.98
(iii) 25mm Sq.M. 2,737.54
In Ground Floor.
(a) Ordinary Teak. Sq.m. 585.27
Page 73 of 338
In Ground Floor.
(i) 4.5mm thick
(a) Ordinary Teak. Sq.M. 563.25
(b) Local Sal. Sq.M. 435.39
In Ground Floor.
(i) 4mm thick
(a) Sal Local Sq.M. 495.18
(ii) 6mm thick
(a) Sal Local Sq.M. 642.05
(iii) 12mm thick
(a) Ordinary Teak. Sq.M. 1,005.16
Partition with soft insulation board (of 12mm thick) as per design
fitted and fixed complete (excluding the cost of supporting frame
work and teak wood battens / lipping but including necessary
wood battens of size 40mm x 25mm) [ P - 269 / 119 ]
In Ground Floor.
(a) Ordinary Teak. Sq.m. 578.59
(b) Local Sal. Sq.m. 450.73
In Ground Floor.
(a) Plain : Exterior grade.
(i) 6mm Sq.M. 671.16
(ii) 8mm Sq.M. 811.54
(iii) 12mm Sq.M. 909.02
In Ground Floor.
Glossy / Matt / Suede excluding surface texture or metallic
lustre.
(i) Thickness of laminate 1.5mm Sq.M. 848.02
(ii) Thickness of laminate 1 mm
Sq.M. 663.29
In Ground Floor.
(i) 4mm thick Sq.M. 613.55
(ii) 6mm thick Sq.M. 760.42
(iii) 12mm thick Sq.M. 995.67
In Ground Floor.
(i) 4.5mm thick
(a) Teak Wood Sq.M. 552.69
(b) Sal Local Sq.M. 424.83
(A) Add extra over rate of ground floor for each addl. Storey for
items:- 95 to 100, 116 to 124,127,130,135,136,139,143 to
148,151,152,155 to 159. [ P - 277 / 128 ]
(i) Upto 4th floor Sq.M. 8.93
(ii) Above 4th floor Sq.M. 11.16
Rough dressed timber planks fitted and fixed with nut bolts
excluding frame work complete : [ P - 277/ 130 ]
In Ground Floor.
(i) 25mm thick planks
(a) Malayasion Sal. Sq.M. 1,532.06
(b) Sal Local Sq.M. 1,286.65
(ii) 35mm thick planks
(a) Malayasion Sal. Sq.M. 2,124.54
(b) Sal Local Sq.M. 1,775.51
(iii) 50mm thick planks
(a) Malayasion Sal. Sq.M. 3,020.21
(b) Sal Local Sq.M. 2,519.57
Page 76 of 338
In Ground Floor.
(a) 19mm mesh. Sq.M. 359.54
(b) 25mm mesh Sq.M. 330.04
(c) 37.5mm mesh Sq.M. 308.95
In Ground Floor.
(a) 50mm x 25mm x 2.7mm x 2.7mm. Sq.M. 210.84
Page 77 of 338
Renewing G.I. sheet door with old sheet but with new local sal
wood frame (styles, rails and diagonal braces 100mm x 35mm)
including fitting, fixing with proper screws and rehanging shutter
with haskal and doomney (excluding the cost of haskal and
doomney). [ P - 283 / 140 ]
Sq.M. 1,282.70
Renewing G.I. sheet door with new 0.63 mm sheets but with old
local sal wood frames (styles, rails and diagonal braces 100mm
x 35mm.) including fitting, fixing with proper screws and
rehanging shutters with haskal and doomney (excluding the cost
of haskal and doomney). [ P - 283 / 141 ]
Sq.M. 575.16
(a) Supplying fitting and fixing I.S.I. approved quality and brand
hydraulic (oil check) floor door spring, heavy duty double action
with brass shoe, brass top centre aluminium top cover etc.
complete set as per direction of Engineer-in-charge.
[ P - 283 / 142(a) ]
Set 2,323.24
(b) Supplying fitting and fixing Godrej type hydraulic (oil check)
floor door spring, heavy duty double action with brass shoe,
brass top centre aluminium top cover etc. complete set as per
direction of Engineer-in-charge. [ P - 283 / 142(b) ]
Set 3,870.09
In Ground Floor.
(i) 32mm thick Sq.M. 3,200.48
(ii) 25mm thick Sq.M. 2,982.74
[ P - 285 Supplying fitting and fixing 30mm th. Factory made solid Panel
/ 145 ] P.V.C. door shutter consisting of outer frame made out of M.S.
tubes of 19 gauge thickness and size 19mm x 19mm for styles,
top and bottem rails, M.S. frame shall have cost of steel primers
of approved make and manufacture, M.S.frame covered with 5
mm th. heat moulded PVC "C" chanel of size 30 mm th. 70 mm
width out of which 50 mm shall be flat and 20mm shall be
tapered in 45 degree angle on either sides forming styles and
5mm th. 95mm wide PVC sheet out of which 75mm shall be flat
and 20mm tapered in 45 degree on the inner side to form top &
bottem rail and 115mm wide PVC sheet out of which 75mm shall
be flat and 20mm shall be tapered on both sides to form lock rail.
Top, bottem and lock rails shall be provided either side of the
panel with 10mm (5mm x 2 ) th. 20mm wide cross PVC sheet as
gap insert for top rail and bottem rail. Paneling of 5mm th. both
side PVC sheet to be fitted in the M.S. frame welded / sealed to
the styles & rails with 7mm (5mm + 2mm)th. x 15 mm wide PVC
sheet beading on inner side and joined together with solvent
cement adhesive. An additional 5 mm th. PVC strip of 20 mm
which is to be stuck on the interior side of the "C" channel using
PVC solvent adhesive etc. complete excluding all necessary
hardwares as per direction of EIC. [ P - 285 / 145 ]
[ P - 287 Supplying fitting and fixing 30mm th. both side prelaminated
/ 146 ] Factory made solid Panel P.V.C. door shutter consisting of outer
frame made out of M.S. tubes of 19 gauge thickness and size
19mm x 19mm for styles, top and bottem rails, M.S. frame shall
have cost of steel primers of approved make and manufacture,
M.S.frame covered with 5 mm th. heat moulded PVC "C" chanel
of size 30 mm th. 70 mm width out of which 50 mm shall be flat
and 20mm shall be tapered in 45 degree angle on either sides
forming styles and 5mm th. 95mm wide PVC sheet out of which
75mm shall be flat and 20mm tapered in 45 degree on the inner
side to form top & bottem rail and 115mm wide PVC sheet out of
which 75mm shall be flat and 20mm shall be tapered on both
sides to form lock rail. Top, bottem and lock rails shall be
provided either side of the panel with 10mm (5mm x 2 ) th.
20mm wide cross PVC sheet as gap insert for top rail and
bottem rail. Paneling of 5mm th. both side PVC sheet to be fitted
in the M.S. frame welded / sealed to the styles & rails with 7mm
(5mm + 2mm)th. x 15 mm wide PVC sheet beading on inner side
and joined together with solvent cement adhesive. An additional
5 mm th. PVC strip of 20 mm which is to be stuck on the interior
side of the "C" channel using PVC solvent adhesive etc.
complete excluding all necessary hardwares as per direction of
EIC. [ P - 287 / 146 ]
In Ground Floor. Sq.M. 2,513.70
[P- Supplying fitting and fixing 30mm th. Double Leaf Factory made
289 / solid Panel P.V.C. door shutter consisting of outer frame made
147 ] out of M.S. tubes of 19 gauge thickness and size 19mm x 19mm
for styles, top and bottem rails, M.S. frame shall have cost of
steel primers of approved make and manufacture, M.S.frame
covered with 5 mm th. heat moulded PVC "C" chanel of size 30
mm th. 70 mm width out of which 50 mm shall be flat and 20mm
shall be tapered in 45 degree angle on either sides forming
styles and 5mm th. 95mm wide PVC sheet out of which 75mm
shall be flat and 20mm tapered in 45 degree on the inner side to
form top & bottem rail and 115mm wide PVC sheet out of which
75mm shall be flat and 20mm shall be tapered on both sides to
form lock rail. Top, bottem and lock rails shall be provided either
side of the panel with 10mm (5mm x 2 ) th. 20mm wide cross
PVC sheet as gap insert for top rail and bottem rail. Paneling of
5mm th. both side PVC sheet to be fitted in the M.S. frame
welded / sealed to the styles & rails with 7mm (5mm + 2mm)th. x
15 mm wide PVC sheet beading on inner side and joined
together with solvent cement adhesive. An additional 5 mm th.
PVC strip of 20 mm which is to be stuck on the interior side of
the "C" channel using PVC solvent adhesive etc. complete
excluding all necessary hardwares as per direction of EIC.
[ P - 289 / 147 ]
In Ground Floor. Sq.M. 2,312.89
Page 79 of 338
[P- Supplying fitting and fixing 30mm th. both side prelaminated
291 / Double Leaf Factory made solid Panel P.V.C. door shutter
148 ] consisting of outer frame made out of M.S. tubes of 19 gauge
thickness and size 19mm x 19mm for styles, top and bottem
rails, M.S. frame shall have cost of steel primers of approved
make and manufacture, M.S.frame covered with 5 mm th. heat
moulded PVC "C" chanel of size 30 mm th. 70 mm width out of
which 50 mm shall be flat and 20mm shall be tapered in 45
degree angle on either sides forming styles and 5mm th. 95mm
wide PVC sheet out of which 75mm shall be flat and 20mm
tapered in 45 degree on the inner side to form top & bottem rail
and 115mm wide PVC sheet out of which 75mm shall be flat and
20mm shall be tapered on both sides to form lock rail. Top,
bottem and lock rails shall be provided either side of the panel
with 10mm (5mm x 2 ) th. 20mm wide cross PVC sheet as gap
insert for top rail and bottem rail. Paneling of 5mm th. both side
PVC sheet to be fitted in the M.S. frame welded / sealed to the
styles & rails with 7mm (5mm + 2mm)th. x 15 mm wide PVC
sheet beading on inner side and joined together with solvent
cement adhesive. An additional 5 mm th. PVC strip of 20 mm
which is to be stuck on the interior side of the "C" channel using
PVC solvent adhesive etc. complete excluding all necessary
hardwares as per direction of EIC.
In Ground Floor. [ P - 291 / 148 ] Sq.M. 2,714.49
Mtr. 335.97
Mtr. 431.33
Page 80 of 338
In Ground Floor.
(a) Moulded door using 2 mm moulded PVC sheet or 2 mm
etched moulded PVC sheet on one side & 2 mm PVC sheet on
other side. Sq.M. 3,072.05
(b) Moulded door using 2 mm Prelam moulded PVC sheet on
both side. Sq.M. 3,505.46
In Ground Floor.
(a) Moulded door using 2 mm moulded PVC sheet or 2 mm
etched moulded PVC sheet on one side & 2 mm PVC sheet on
other side. Sq.M. 3,807.99
(b) Moulded door using 2 mm Prelam moulded PVC sheet on
both side. Sq.M. 4,241.58
PVC PARTITION :-
Supplying fitting and fixing the partition, frame will be made with
rectangular steel tube of size 50mm x 25mm Wall thickness not
less than 1.00 mm. The vertical members duly welded to the
horizontal members shall be placed between 1000mm to
1200mm apart the entire partition frame will be securedly fixed to
the wall, ceiling and floor using rawlplug or gutties and screw etc.
the frame will be painted with synthetic print, the section of the
partition frame will then fitted with PRINTED LAMINATED P.V.C.
extruded hollow section of size 100mm x 25mm Panels with
approved quality fixed in the place by means of P.V.C. extgruded
beading on both sides or P.V.C. extruded angles (20mm x
18mm) on one side and P.V.C. extruded beading (9mm x 9mm)
on the other side angle/beadding will be fixed to the steel frame
by 19mm. (No.6) self tapping steel screw placed at an interval of
450mm and complete in all respect as per direction of Engineer-
in-charge with all labour and materials. [ P - 303 / 158 ]
(a) Depth or width (75 mm. to 100 mm.) (Cement 1.25kg/m) Metre 28.32
(b) Depth or width (125 mm. to 150 mm.) (Cement 1.65kg/m) Metre 36.34
(a) Depth or width (75 mm. to 100 mm.) (Cement 2.00kg/m) Metre 40.97
(b) Depth or width (125 mm. to 150 mm.) (Cement 2.60kg/m) Metre 49.07
(a) Depth or width (75 mm. to 100 mm.) (Cement 2.50kg/m) Metre 41.81
(b) Depth or width (125 mm. to 150 mm.) (Cement 3.50kg/m) Metre 55.22
(a) Depth or width (75 mm. to 100 mm.) (Cement 3.50kg/m) Metre 56.32
(b) Depth or width (125 mm. to 150 mm.) (Cement 3.74kg/m) Metre 61.44
(a) Depth or width (75 mm. to 150 mm.) (Cement 2.46kg/m) Metre 47.28
(a) Depth or width (75 mm. to 150 mm.) (Cement 3.30kg/m) Metre 58.93
in Ground floor.
(i) with rabbet on one side
(a) With moulding on one side only (Cement 1.5kg/m) Metre 31.62
(b) With moulding on both sides (Cement 2.0kg/m) Metre 36.97
in Ground floor.
(i) Projection (75 to 125) mm.
Plaster (to wall, floor, ceiling etc.) with sand and cement mortar
including rounding off or chamfering corners as directed and
raking out joints or rougening of concrete surface, including
throating, nosing and drip course where necessary (ground floor)
[ P- 319 / 2 ]
(iv) 2:1 cement mortar (to be used in floors and for special
works)
Plaster (to wall, floor, ceiling etc.) with composite mortar of sand,
lime and cement including round off or chamfering corners as
directed and raking out joints and roughening of concrete
surface including throating, nosing and drip course where
necessary (ground floor). [ P- 321 / 3 ]
Extra for each additional floor over the rate for ground floor items
2 to 4 : [ P- 323 / 5 ]
Neat cement punning about 1.5 mm. thick in wall, dado, window,
sills, floor, drain etc. [ P- 323 / 8 ] Sqm 28.51
Lime punning about 3 mm. thick with shell lime and stone lime
(2:1) [ P- 323 / 9 ] Sqm 59.08
Closing gap between door and window frame and jambs with
cement mortar (3:1) including removing old mortar (throughout
entire surface of contact) and cleaning the joint. (Cement 0.12
Cu.m/100 Sq.m.) [ P- 325 / 13 ]
% Mtr. 746.67
NOTE : For 17 & 18 cement 0.091 cu.m. sand 0.365 cu.m. per
sq.m.
Rule pointing to brick work with ruled joints in surki and lime 2:1
mortar including raking out joints and top finishing (2 surki : 1
lime paste/ putty). [ P- 325 / 20 ]
Sqm 39.68
Sqm 134.27
(b) 12.5 mm thick plaster Sqm 97.36
N.B. : Extra for each additional floor in external walls refer item
20.
N.B. : Extra for each additional floor in external walls refer item
20.
N.B. : Extra for each additional floor in external walls refer item
20.
N.B. : Extra for each additional floor in external walls refer item
20.
Two coats.
In ground floor
(a) One coat.
i) Water based interior grade Acrylic primer. %Sqm 2,545.20
ii) Solvent based interior grade Acrylic primer. %Sqm 2,838.10
(b) Two coats.
i) Water based interior grade Acrylic primer. %Sqm 3,686.50
ii) Solvent based interior grade Acrylic primer. %Sqm 4,130.90
In ground floor
(a) One coat. %Sqm 2,585.60
(b) Two coats. %Sqm 3,747.10
N.B. This item is to be done under specific instruction of the
Superintending Engineer.
N.B.:-Extra for each additional floor in external walls refer item
20.
In ground floor.
In Ground floor
(i) Two Coat Sqm 92.21
N.B. This item is to be selected only with written permission of
Superintending Engineer for very resticted and small areas of a
building
Add extra for each additional floor over the rate for ground floor
on items 4 to 7 and item 15,16,18 & 19. [ P - 337 / 20 ]
External surface
NOTE: For all structures the ground floor equivalent height shall
be taken as 4 meters.Every 4 meters or part thereof above 4
meters shall be taken as each additional floor for purpose of item
4, 5, 6, 7 and 15,16,18 & 19.
(b) Washing & cleaning the wall surface & ceiling by soft
detergent powder & soft water & render the surface free of dust,
stain etc. [ P-341 / 6 ] Sqm 5.25
(iv) Two coats (with any shade except white) Sqm 62.62
Painting with ready mixed red lead paint of approved make and
brand : [ P-345 / 10 ]
Borders (up to 150 mm. width) with two coats of Black Japan
paint. [ P-347 / 12 ] Mtr. 6.40
Washing and cleaning old painted surface and oiling with linseed
oil. [ P-347/ 13 ] Sqm 4.67
Page 95 of 338
Cleaning old painted surface and oiling with linseed oil with
admixture of paint (25% of linseed oil by volume.) [ P-347 / 14 ] Sqm 6.87
NOTE : For high gloss polish the rate shall be increased by 50%
over the rate for ordinary gloss. This work should not be
executed without specific permission of Superintending
Engineer.
Ready mix Wax polishing to wood work including preparing
surface. [ P-349 / 19 ]
GLARZIER'S WORK
W.C.II
Supplying best Indian sheet glass panes set in putty and fitted
and fixed with nails and putty complete ( in all floors for internal
wall & upto 6 m height for external wall ) [ P-351 / 1 ]
Supplying best Indian sheet glass panes set in putty (as per
I.S.specification) and fitted and fixed with teak wood beads and
nails complete( in all floors for internal wall & upto 6 m height for
external wall ) [ P-351 / 2 ]
Extra labour for fixing glass panes in steel window. [ P-353 / 7 ] Sqm 42.22
Cleaning and removing paint mark from glass pane with spirit
and removing strains etc. [ P-353 / 10 ] Each 11.31
Add 5% extra for each 6 mtr. height or part thereof beyond the
initial height of 6 mtr. for item 1 to 5 & 10 only. This extra rate is
applicable for external works. For maintenance work , 20% extra
on the rate of corresponding item to be added. [ P-353 / 12 ]
Sauceer drain upto 150 mm. Width in floor and upto 75 mm.
Depth including ceeeement plaster (3:1) and neat cement
finishing. [ P-355 / 3 ]
%Metre 2,783.56
Regrading mouth of down pipe for easy out let of rain water
including cement plaster (3:1) including cutting slope and
mending damages. [ P-355 / 4 ]
Each 13.39
Making kutttcha drain upto 450 mm. Deep and upto 750 mm.
Width to grade including trmming sides and beds, removing
spoils to any distance and speading. [ P-355 / 6 ]
Metre 20.23
(b) Above 100 mm. And upto 150 mm.Square or round. Each 112.69
G.I. Rain water spout 75 mm. Dia. And 600 to 750 mm. Long
supplyed fitted and fixed complete with two coats of paint to both
exposed portin. [ P- 361 / 18 ]
Each 136.35
A) UPVC Pipes :-
(a) 75 mm. Dia. Metre 163.12
(b) 100 mm. Dia. Metre 260.48
(c) 150 mm. Dia. Metre 559.04
Page 101 of 338
B) UPVC Fittings :-
a) Plain Tee.
(a) 75 mm. Dia. Metre 106.96
(b) 100 mm. Dia. Metre 190.28
(c) 150 mm. Dia. Metre 590.04
b) Plain Y.
(a) 75 mm. Dia. Metre 134.33
(b) 100 mm. Dia. Metre 250.88
(c) 150 mm. Dia. Metre 675.69
d) Shoe
(a) 75 mm. Dia. Metre 78.38
(b) 100 mm. Dia. Metre 117.67
(c) 150 mm. Dia. Metre 348.45
Strong bamboo posts, posts plates, refters, ties etc. fitted and
fixed complete with coir rope or nails as directed. (Embedded
portion of posts shall also be paid for against this item cost of
digging hole and repacking being paid for seperately) :
[ P- 367 / 2 ]
Renewing with part old and part new materials bamboo frame
works (of thatched roof) consisting of 75 mm. dia, full bamboo
rafters spaced at 350 mm. centres and tied with tranverse
bracing at 380 mm. spacing (each bracing consisting of pair of
quarter bamboo,one at top and the other at bottom of the rafters)
fitted and fixed in position. [ P- 367 / 4 ]
(a) With half old and half new materials Sqm 124.12
(b) With one fourth old and three-fourth new materials Sqm 146.56
Page 102 of 338
Single durma mat lining (over bamboo roof frame) fitted and
fixed complete. [ P- 369 / 6 ]
Sqm 53.13
Renewing single durma mat lining (over bamboo roof frame) with
half old and half new material fitted and fixed complete.
[ P-369 / 7 ] Sqm 31.92
Renewing rice straw thatching in roof with half old and half new
material including ridges and hip with entirely new materials :
[ P- 369/ 9 ]
(a) With half old and half new materials Rmt 41.92
Renewing split bamboo jaffry in thatched roof with half old and
half new materials fitted and fixed in position : [ P- 369 / 13 ]
Renewing with half old and half new materials diagonally woven
crushed bamboo mat including durma amt lining and both
longitudinal and tranverse intermediate stffiners (about 300 mm
centre each way) made on each face and tied with entirely new
18 B.W.G.galvanised wire fitted and fixed in position
complete(but excluding the cost of supporting frame work) :
[ P- 371/ 19 ]
Renewing with half old and half new materials bamboo walling
made of crushed bamboo or split bamboo or bamboo twigs
(kanchis) as directed and tied with necessary stiffners of split
bamboo (in pairs) fitted and fixed complete (but excluding the
cost of supporting frame work) [ P- 373 / 21 ]
Sqm 65.75
100 mm. thick dab wall made of bamboo walling (with crushed
bamboo or split bamboo twigs) mud plastered both sides and
finished with lipping of earth and cowdung (4:1) mixture
complete but excluding the cost of supporting frame work)
[ P- 373 / 22 ]
Sqm 80.60
Thick mud walling made with prepared and weathered earth and
admixture of straw chopping etc. (land where from earth may be
obtained will be made available by the dept. within 100 metre).
[ P- 373 / 23 ]
Cum 216.54
Mud pluster (25 to 37.5) mm. thick with prepared mixture of earth
and cowdung (10:1) with admixture of straw chopping and
finishing smooth with lipping of earth and cowdung (4:1):
[ P- 373 / 25 ]
Renewing with half old half new materials durma mat works
strengthened with split bamboo placed both ways (225 mm.
apart) on both sides and tied together fitted and fixed complete
(but excluding the cost of supporting frameworks) :[ P- 375 / 28 ]
FENCING
W.C.II
Fixing post of iron or precast concrete by digging hole in the
ground (in all sorts of soil) and embedding the same by packing
the hole with cement concrete (6:3:1) (with jhama khoa) and
finishing the top surface to regular shape (as directed) with 15
cm. cement plaster (6:1) complete, including the cost of
concrete, plaster etc.but excluding the cost of the post : [ P-
377 / 1 ]
(b) Depth exceeding 500 mm. but not exceeding 600 mm.
Each 185.26
(c) Depth exceeding 600 mm. but not exceeding 675 mm.
Each 209.76
(d) Depth exceeding 675 mm. but not exceeding 750 mm.
Each 231.03
(b) Depth exceeding 500 mm. but not exceeding 600 mm.
Each 328.69
(c) Depth exceeding 600 mm. but not exceeding 675 mm.
Each 370.69
(d) Depth exceeding 675 mm. but not exceeding 750 mm.
Each 410.46
Labour for fitting wove wire or similar fencing net tightening and
fixing the same to post with staples at every bar (including the
cost of cutting and lapping joints in the net, the cost of staples,
binding wire etc. and of labour for fixing such staples as
necessary). [ P- 381 / 7 ]
Labour for taking out wove wire or similar net (from fencing)
including the cost of taking out staples (by cutting or
otherwise,as necessary). [ P- 383/12 ]
(a) Net upto 1350 mm. height %Rmt 288.86
Taking out bulged out wire netting fitted and fixed in window
frames with nails and refixing the same after straightening with
new galvanised staples and lapping with new (50 x 13) mm.
Badam/ Gamari batten fitted and fixed with iron screws including
hire and labour of scaffolding complete. [ P- 385 / 17 ]
Sqm 25.44
Double knotted wove wire 1.2 m. height (11 bars), vertical 300
mm. apart,horizontal spacing starting from 88 mm. ending 200
mm. top and bottom wire 10g and all other intermediate and
upright wire 9g. with finished border 2 ply twisted fencing
including tightening and fixing the same to posts with staples at
every bar including cost of cutting and of lapping joints in the net
as necessary including cost of staples and wove wire.
[ P- 385 / 18 ]
Mtr. 370.80
Double kontted wove wire 2.1 m height (17 bars) vertical 300
mm apart horizontal spacing starting from 88 mm ending 200
mm top and bottom wire 10g and all other intermediate and
upright wire 9g with finished border 2 ply twisted fencing
complete including tightening and fixing the same to pots with
staples at every bar including cost of cutting and of lapping joints
in net as necessary including cost of staples and wove wire.
[ P- 387 / 19 ]
Mtr. 644.39
(b) Double brick flat soling (thickness 150 mm.) Sqm 490.96
(b) Double brick flat soling (thickness 75 mm. plus 75 mm.) %Sqm 3,338.05
(e) Soling or dry pavement with one brick thickness (125 mm.)
(laid in herring bone pattern) %Sqm 3,338.05
(f) Soling (125 mm. thick) or dry pavement with one brick-on-
edge. %Sqm 3,777.40
%Metre 5,316.64
(a) 100 mm. wide and 125 mm. deep edging with stone sets
laid-on-edge. %Metre 860.52
(b) 100 mm. wide and 250 mm. deep edging with stone sets
laid-on-edge. %Metre 1,223.11
(a) 100 mm. wide and 125 mm. deep edging with stone sets
laid-on-edge. %Metre 1,160.00
(b) 100 mm. wide and 250 mm. deep edging with stone sets
laid-on-edge. %Metre 1,718.00
Labour for taking out soling from road and stacking serviceable
materials at site. [ P- 399 / 16 ]
Hire and labour charges for high scaffolding all round (outside)
body domes and finials etc. of Saheed Minar. [ P- 401 / 5 ] L.S. 0.00
Hire and labour charges for high scaffolding all round (outside)
body domes and finials etc. of Luscar Memorial. [ P- 401 / 6 ] L.S. 0.00
ALUMINIUM WORKS
1) Natural white
g) Fixed glazing.
h) louvered window.
h) Fixed partitions.
l) Rimless door.
II) Coloured
g) Fixed Glazing.
h) Fixed partitions.
j) Fixed partitions.
g) Fixed glazing.
h) louvered window.
h) Fixed partitions.
j) Fixed partitions.
l) Rimless door.
Page 119 of 338
The rate includes the hire charge of all tools and plants,
including all incidental charges, adhesive, joineries such as
screw, cleate angle etc. but excluded the cost of extruded
sections, glass, neoprene / EPDM gasketing, locking
arrangement and rollers
i) 2 track sliding window. Sq.M. 471.77
P-421 (B) Partly glazed partly panelled or fully glazed single leaf
alunminium swing door made of extruded and annodized alloy
aluminium sections, fabrication including cutting to proper shape
and size, drilling and aligning, fitted with heavy duty hydraulic
action floor sping placed in the floor with mending damages,with
top pin assembly of approve make and brand, fitted with in built
locking arrangement, flush bolt, glazing clips and all other
necessary fittings, fixtures, adhesives and joineries, cutting glass
of approved make to requisite shape and size fitting with dry set
neoprene or EPDM gasketing, cutting to requisite shape and
size panel board (prelaminated particle block) fixing them with
glazing clips as per drawing, specification and direction of
Engineer in charge.
Sq.M. 948.29
Page 120 of 338
The rate includes the hire charge of all tools and plants,
adhesive, joineries such as screw, cleate angle etc. but excluded
the cost of extruded sections, glass, neoprene / EPDM
gasketing, locking arrangement, weather gasketing / wool pile,
floor spring, top pin, handle tower bolt, glazing clips etc. (10%
rate reduction has to be made for swing doors or partitions
where floor sping is not uses. 10% enhensement of rate is to be
made where door frame of extruded aluminium sections has to
be fitted and fixed to masonry wall. 5% rate enhencement may
be allowed for double leaf swing door. Payment shall be made
for the shutter area only exept where door frame is fixed the
entire opening shall be taken to consideration.Payment for door
frame sections are to be paid seperately).
P-423 (c) Fully glazed single leaf reamless swing door of anodized
aluminium alloy extrusions fabrication after cutting to proper
shape and size, drilling and alining fitted with heavy duty
hydrolic action floor spring with top pin assembly and fitted with
inbuilt locking arrangement and all other necessary fittings,
fixture, adhesives and joineries, cutting the glass to requisite
shape and size mounting the edges for fitting the same with set
neoprine /EPDM gasket.
Sq.M. 1,085.75
The rate includes the hire charge of all tools and plants,
adhesive, joineries but excludes the cost of extruded sections,
glass, EPDM gasket, locking arrangement, weather gasketing /
wool pile, floor spring, top pin, handle, tower bolt etc.
The rate includes the hire charge of all tools and plants,
adhesive, joineries such as screw, fastener but excludes the
cost of extruded aluminium sections, EPDM gasket, glass,
board, glazing clips, locking arrangement, etc.
Note :- Add extra for each Addl. Floor over the rate of item
2A, 2B, 2C and 2D except 2A(vi).
i) Upto 4th. Floor Rs. 12.00 per Sq.M.
ii) Above 4th. Floor Rs. 16.00 per Sq.M.
iii) weather gaskett / wool pile for door vertical. Mtr. 18.03
P-433 iii) 1.8 metre diameter of digging for 1.5 metre internal
diameter of well ring.
P-435 ii) 2.4 metre diameter of digging for 1.5 metre internal
diameter of well.
N.B. a) Extra 10% per meter for work beyond the initial depth of
18 metre will be paid.
P-439 c) Extra rock cutting over the corresponding rate for digging for
the respective internal diameter of the well will be allowed on the
different stages of depth.
ii) 100% extra in Laterite rock or sand stone cutting with chisel
and jumpers, but not requiring blasting.
iii) 200% extra in hard rock requiring blasting including cost of
explosive etc., and done with permision from the Engineering-in-
Charge.
iv) 300% extra in hard rock in built up areas using chisel, jumper
and manual labour.
R.C. C. well ring made with cement concrete 1:1.5:3 with stone
chips and 0.80% reinforcement (including the cost of shuttering
and reinforcement) fitted and fixed in position after proper curing
true to plumb in the well including jointing with cement morter 2:1
complete as per direction. [ P- 439 / 2 ]
Supplying and fitting fixing in position 15 cm Dia. C.I. Pully (extra Each 432.08
payment will be made for pully bar and other allied ite in
respective item) [ P- 439 / 3 ]
1st class brick work for staining wall of well in cement morter 4 :
1 below G.L. including cuttng bricks if required. [ P- 439 / 4 ]
Taking out and removing silt from the bottom of well after bailing
out water, removing moss and weed from the well surface (by
wire brush) and disinfecting the well complete. [ P- 441 / 5 ]
Removing and cleaning hard scum and silt from the bottom of
the masonry well from 45cm below the ordinary silt level the kerb
level. [ P- 443 / 6 ]
Sinking Precast R.C. well ring made with cement concrete 1:2:4
with stone chips and necessary reinforcement fitted and fixed in
position true to plumb including all labours and hire charges of
tools and plant complete as directed jointing rings with cement
(a) 90 cm
morter (2 :dia
1) [ P- 443 / 7 ] Metre 160.60
cement for joint filling 4 kg/mtr.
Page 127 of 338
MISCELLANEOUS WORKS
W.C.II
Number plaque of building (plaque size up to 225 mm x 225 mm)
made of sand cement plaster (2 : 1) on face of wall or plinth with
50 mm size letters P.W.D and the number of the structure formed
thereon (in sunk type0 including painting the letters and the
number complete as per direction. [ P- 445 / 1 ]
Each 76.99
( Cement - 1 kg / No )
(B) Stitching crack in brick wall by carefully cutting out face brick Block 31.55
250 mm. - 1
( Cement long, 75 ) mm. thick and 125 mm deep into the
kg / No
wall,cleaning the gap and filling up the same with sound new
brick, carefully set in cement mortar (3:1) including mending
(C)
goodRenewing
damagesweathered facethe
and finishing brick including
surface takingwith
to match outadjacent
the old
brick completely and setting
areas complete as per direction. the head brick carefully in cement
[ P- 447 / 5 ]
mortar (3:1) complete,including making good all damages.
[ P- 447 / 5 ]
P-449 (b) With baluster of plain cement concrete with (3:1½:1) with
stone chips(floral or intricate pattern of height not exceeding
1200 mm.) Each 292.75
Vertical sleeve joint in wall etc. or horizontal joint in floor roof etc.
Including shaping and finishing adjacent surface and caulking
the joint with hemp rope thoroughly soaked in bituminous
material and fixing rope in position by staples or other suitable
devices complete as per direction (including cost of all materials)
[ P- 449 / 7 ]
(a) Small plant of girth of exposed stem upto 75 mm. lift upto 6
mtr. Each 38.22
Page 129 of 338
(c) Large plant of girth of exposed stem above 150 mm. but not
exceeding 225 mm. lift upto 6 mtr. Each 123.10
Note : For lift beyond initial 6 mtr. the rate will be increased @
20% for each additional lift if 6 mtr. or part thereof
NOTE : Height of the bottom of the tank not less than 15 mtrs.
Page 130 of 338
(a) With bamboos of length between 1.20 m. and 1.80 m. each. Metre 649.05
(a) Brick gabion 1.50 m.internal diameter and 1.20m. high with
150 mm. deep solid brick band (in 6:1 cement mortar) at
base,125 mm.thick body of jaffry brick work set in cement mortar
(4:1) and 150 mm. deep solid brick band at top in cement mortar
6:1 and cement plaster (6:1) (all faces) including colour wash (all
surfaces) to the top band and redoxide or similar approved wash
(all surfaces) to the remaining portion, complete as per direction.
[ P- 459 / 29 ]
Each 3,059.69
( Cement - 105 kg / No. )
(b) Mending good damages to brick gabions (with old materials
as available and with new materials as necessary) including
fresh colour wash and oxide wash to the entire gabion.
[ P- 459 / 29 ]
(i) When less than half gabion has to be restored. Each 718.82
( Cement - 25 kg / No. )
(ii) When more than half the gabion has to be restored. Each 991.01
( Cement - 50 kg / No. )
Making gabions from old tar or bitumen drums after cutting strips
75 mm wide x 300 m long including fitting and fixing in position
using 1½ No of drums for each gabion excluding cost of drums
but including carriages from departmental godown to site of
work. [ P- 459 / 30 ]
Each 239.20
Making gabions from old tar or bitumen drums after cutting strips
75 mm wide x 300 m long including fitting and fixing in position
using one number of drums for each gabion excluding cost of
drums but including carriages from departmental godown to site
of work. [ P- 459 / 31 ]
Each 173.76
(ii) When laid with cement mortar (6:1) on the under side as
well (including cost thereof)
Taking out stone slabs of flat V-shaped drain of road side and
resetting the same to correct line and level with cement mortar (4
: 1) including cement pointing (2 :1). [ P- 461 / 33 ]
(a) 75mm. dia bamboo railing & 125mm. dia Jhau / Eucalyptus /
other approved timber posts @ 1.60m apart
(b) 75mm. dia bamboo railing & 100mm. dia bamboo posts @
1.40m. apart.
(a) 100 mm. dia bamboo railing and 150 mm. dia. Jhau /
Eucalyptus posts @ 1.80 m. apart.
Hire and labour charges for coir rope fencing 25 mm dia rope
single on 120 m dia bamboo posts 1.40 m above G.L and 600
mm below G.L 1.50 m apart including digging holes complete.
[ P- 465 / 37 ]
Metre 13.78
Hire and labour charges for coloured and twisted cloth rope
fencing as per design approved by Engineer-in-charge one line
with 100 mm dia salbullah or bamboo posts 0.60 m above G.L
and 300 mm below G.L 1.50 m apart fitted and fixed complete
including painting with white zinc painting (2 coat) complete.
[ P- 467/ 38 ]
Metre 17.00
Payment of Painting to be made separately.
Labour for fitting and fixing special type M.S calmp with
necessary wooden packing to Elec. Lamp post upto 7.60 m
height with necessary scaffolding and tightening the bolts and
nuts and one coat of white painting complete including
dismantling the clamps and depositing the same to P.W.D office
after the foundation. [ P- 467 / 39 ]
Each 46.22
Hire and labour for erecting new thick canvas shade 6.10 m x
3.70 m with roof covering with strong bamboo frame for 2 nos
ladies cloak room with canvas on all sides as per direction of
Engineer in charges including maintaining the shades as
required including fitting and fixing white squatting urinals and
one pan complete with drainage as directed. [ P- 469 /
42 ]
Set 5,206.15
Page 134 of 338
Hire and labour charges for providing Drop Gate with 15 cm dia
salbullah of length not less than 8 meter including hoisting and
fitting fixing with bolts and nuts to vertical posts (100 mm dia : 2
nos on each flank embedded 750 mm below G.L) and providing
counter load of concrete of stone of iron block at the fulcrum end
including painting two coats in alternate band providing STOP
plate jute rope of necessary length etc complete including
dismantling and removing as per direction of the Engineer in
charge. [ P- 469 / 45 ]
Each 569.94
Labour charge for hoisting and fitting fixing drop gate including
carriage of the gate by parts from the departmental godown /
stack yard and dismantling and returning the gate to the place of
supply as per direction of the Engineer in charge. [ P- 469 / 46 ]
Each 419.96
7.5 cm. thick compacted lime concrete with moorum and best
quality slaked stone lime ( 5% by volume) properly mixed, laid
and rammed on bed of foundation including cost of all materials,
labour and curing etc. complete in all respect as per direction of
Engineer-in-Charge (10 cm. loose consolidated to 7.5 cm. thick).
[ P- 471 / 50 ]
Sqm 106.10
(b) Made of cement concrete 6:3:1 with stone chips or gravel Each 282.03
(a) With carriage upto 150 metre (when the pillars are delivered
near the area by department carriage) Each 32.44
(b) With carriage beyond 150 metre and upto 3.00 Km Each 34.83
(b) With carriage beyond 150 metre and upto 3.00 Km Each 34.83
(c) With carriage beyond 3.00 Km and upto 8 Km. Each 37.16
Painting the vertical end faces and the inside face of pillar or
railing or parapet (1.05 m. to 1.75 m. high) with horizontal
alternate bands in different colours, as directed with approval oil-
bound paint. [ P- 477 / 58 ]
(b) Size above 2.5 cm. and upto 4 cm. Each 7.39
(d) Size above 5 cm. and upto 7.5 cm. Each 9.72
(e) Size above 7.5 cm. and upto 10.0 cm. Each 10.89
(f) Size above 10 cm. and upto 12.5 cm. Each 12.05
(g) Size above 12.5 cm. and upto 15 cm. Each 13.28
(b) 25% extra for painting the l;etters of K.M. post and M Post
etc.
Stone set pavement with the joints set close in cement morter
[6:1] excluding the cost of stone sets but including the cost of
carriage thereof within alead of 150 m. [ P - 481 / 66 ]
i] When laid with a cushion of sand below [including cost
thereof]
ii] When laid with cement morter [6:1] on the underside as well
[including cost thereof]
a] 100 mm thick pavement :- Sq.M. 39.66
b] 125 mm thick pavement :- Sq.M. 45.66
Supplying fitting fixing fan hook for ceiling with 1 metre long 16
mm dia rod complete including mending damages.
[ P - 481 / 67 ] Each 86.99
6] (a) Sand coarse, (Fineness modulus not less than 2) Cu.m. 820.00
(b) Medium sand (fitness modulus 1.8 to 2) Cu.m. 650.00
(c) Fine sand Cu.m. 500.00
(d) Silver sand Cu.m. 450.00
Volumetric rate for preparation of preliminary cost estimate for construction of building.
STRUCTURAL COST :-
iii) 4th course with washed and clear pea size gravel @ 0.006
cu.m. / sq.m.for flat roof and @ 0.006 Cu.M. of medium sand per
Sq.M. for Slope roof.
Page 140 of 338
ANNEXURE - I
Table - 1 - 1 - ISSUE RATE OF CEMENT & STEEL MATERIALS
1 2 3 4 5
1) CEMENT :-
PPC / PSC :- MT 7050.00 6,420.00
OPC (43 / 53 Grade ) :-
MT 7720.00 7,030.00
2) STEEL MATERIALS :-
ii) Tor Steel Rods / HYSD / TMT Bars Fe 415, 500, 500 D. MT 45100.00 41,000.00
3)
STRUCTURAL STEEL : MT 47000.00 0.00
4) G.C.I. SHEET :-
L MATERIALS
5 6
1) Rates furnished in Column-4 of item
1 & 2 are the issue rates of materials
6,420.00 at Departmental Stackyard / Godown.
7,030.00
2) For Sub-items of item-2, the Basic
Prices exclusive of Contractor's Profit
but inclusive of all Taxes and duties,
41,000.00 are given in Column-5. To arrive at
complete rate in case of Steel supplied
41,000.00 by Contractor, Format-B of Annexure-I
is referred.
0.00
3) The rate of items involving use of
Cement supplied by the Contractor
shall be evaluated as per Format-A of
Annexure-I
0.00
Page 146 of 338
(a) (ii) Chromium plated Bib Cock long body with wall
flange with aerator (Equivalent to code no-512 &
Model- Tropical / Sumthing Special of ESSCO or similar
brand). Each 648.00
Page 151 of 338
(f) (i) Polythene Bib Cock / Stop Cock (HD) with metal
inlet (EMCO / ATLAS or equivalent )
(i) 15 mm Each 89.00
(f) (ii) Polythene Bib Cock / Stop Cock with plastic inlet
(EMCO / ATLAS or equivalent )
(i) 15 mm Each 89.00
PWF009 (g) Supplying, fitting and fixing alloy iron with brass
spindle bib cock/ stop cock of approved brand and
make, spray painted and tested to 21 kg per sq. cm.
(c) (i) PTMT push cock (20 mm F/T) with spout (Prayag
of equivalent) Each 149.00
(d) Polythene
(i) 15 mm Each 92.00
(ii) 20 mm Each 107.00
PWF014 P- 20 / 14 C.I. sluice valve with flanged ends drilled to as per I.S.
1358/62 and having all cast iron components as per I.S.
780/71 solid forged bronze inside screw spindle having
ultimate tensile strength not less than 4.72 mt per sq.
cm. Spindle nut valve and seat faces of hard wear
resisting, manufactured from best quality gunmetal
conforming to I.S. 780/71, painted black all over with
asphalt base paint tested to 21 kg (hydraulic pressure)
per sq. cm., valve opening to anticlockwise direction,
fitted and fixed complete. [ P- 8 / 9 ]
PWF015 P- 22 / 15 Sluice valve chamber with C.I. heavy cover with locking
arrangement, (weight not less than 25 kg) (size of
chamber 450 mm X 600 mm inside upto 900 mm
depth) 250 mm thick cement brick walls (6:1), 150 mm
thick cement concrete (6:3:1) bed with jham chips, 19
mm thick cement plaster (6:1) for inside wall and 12
mm thick cement plaster (6:1) for outer walls including
rounding corners. [ P- 8 / 10 ]
each set 7576.00
PWF016 P- 22 /16 Supplying, fitting and fixing C.I. tail pieces in pair
conforming to I.S. specifications. [ P- 8 / 811 ]
(a) Class A:
(b) Class B:
PWF021 P- 26 / 21 Supplying, fitting and fixing self closing C.P. water tap
of approved brand and make - 15 mm dia. [ P- 10 /
15 ] Each 232.00
Page 155 of 338
PWF024 P- 28 / 24 Labour for fitting and fixing high density polythene pipes
or P.V.C. pipes for above ground work including cost of
jointing materials paints etc. fitting and fixing all
necessary specials, cutting pipes, making threads,
cutting holes in walls or R.C. floor where necessary and
mending good all damages excluding the cost of
masonry or concrete work, if necessary, but including
the cost and fitting and fixing holder bat clamps(any
floor) or for underground work including cutting
trenches upto 1.5 metre and refilling the same complete
as per direction of the Engineer-in-charge. (Payment
will be made on centre line measurement of the total
pipeline including specials.) [ P- 11 / 18 ]
PVC pipes
15 mm Mtr 89.00
20 mm Mtr 111.00
25 mm Mtr 150.00
32 mm Mtr 199.00
40 mm Mtr 245.00
50 mm Mtr 325.00
62 mm Mtr 483.00
75 mm Mtr 633.00
100 mm Mtr 904.00
125 mm Mtr 1232.00
150 mm Mtr 1676.00
200 mm Mtr 2515.00
250 mm Mtr 3701.00
300 mm Mtr 5002.00
P-15 B) Socket
15 mm Each 7.65
20 mm Each 10.60
25 mm Each 14.38
32 mm Each 21.92
40 mm Each 31.36
50 mm Each 49.29
65 mm Each 78.60
80 mm Each 95.58
100 mm Each 126.72
125 mm Each 160.69
150 mm Each 217.47
200 mm Each 390.96
PWF027 250 mm Each 491.11
300 mm Each 642.09
C) Elbow
15 mm Each 10.60
20 mm Each 17.21
25 mm Each 23.81
32 mm Each 37.97
40 mm Each 54.95
50 mm Each 87.98
65 mm Each 151.25
80 mm Each 179.56
100 mm Each 302.23
125 mm Each 377.71
150 mm Each 906.29
200 mm Each 1128.05
PWF028 250 mm Each 1510.44
300 mm Each 1812.14
P-16 E) Tee
PWF031 15 mm Each 14.38
20 mm Each 20.98
25 mm Each 29.47
32 mm Each 43.63
Page 159 of 338
40 mm Each 66.27
50 mm Each 98.36
PWF032 65 mm Each 178.62
80 mm Each 260.71
100 mm Each 480.57
125 mm Each 868.63
150 mm Each 1908.64
200 mm Each 2878.65
250 mm Each 3586.09
300 mm Each 4303.21
40 mm Each 85.15
50 mm Each 104.02
65 mm Each 170.12
80 mm Each 228.63
100 mm Each 264.48
125 mm Each 330.53
150 mm Each 453.37
200 mm Each 685.49
PWF035 250 mm Each 1038.39
300 mm Each 1578.13
P-19 G) Flange
15 mm Pair 47.65
20 mm Pair 66.27
25 mm Pair 85.15
32 mm Pair 104.02
PWF036 40 mm Pair 132.20
50 mm Pair 160.63
65 mm Pair 255.05
80 mm Pair 311.66
100 mm Pair 377.71
125 mm Pair 472.07
150 mm Pair 595.16
200 mm Pair 896.85
250 mm Pair 1038.39
300 mm Pair 1321.34
I) Union
15 mm Each 28.53
20 mm Each 41.74
25 mm Each 56.84
32 mm Each 85.15
PWF038 40 mm Each 122.89
50 mm Each 151.20
J) Threaded Cap
15 mm Each 9.66
20 mm Each 14.54
25 mm Each 18.49
32 mm Each 23.56
40 mm Each 33.92
50 mm Each 46.35
65 mm Each 70.11
Page 161 of 338
80 mm Each 88.20
100 mm Each 123.47
125 mm Each 296.13
150 mm Each 303.85
200 mm Each 755.05
250 mm Each 957.14
300 mm Each 1156.66
PWF042
O) Solvent Cement 250 Gm 100.00
i) 15 mm Each 42.00
v) 50 mm Each 149.00
P- 54 / 2 Labour for fitting and fixing G.I. pipes for under ground
work including cost of jointing materials, cutting
pipes,making threads etc. complete in all respect
including cutting trenches upto 1.5 metre below surface
in all sorts of soil and refilling the same as directed with
two coats of painting to G.I. pipes and specials with
bituminous paint. (Payment will be made on the centre
line measurement of the total pipeline including
specials.Payment of painting will be paid seperately.)
[ P- 26 / 34 ]
(a) Plug.
Page 165 of 338
PFR005 P- 60 / 9 Opening out leaky water supply pipe and making the
joints water tight including cutting threads where
necessary. [ P- 30 / 6 ]
PFR007 P- 62 / 15 Cutting out section of G.I. water main pipe upto 100
mm. [ P- 30 / 11 ] Meter 25.00
(a) bib cock/ stop cock/ pillar cock/ waste fittings. Each 35.00
W.C.II
(a) Original Works
CTO003 P- 68 / 11 Supplying, fitting and fixing cast iron raised rain proof
tank cover 450 mm. [ P- 34 / 6 ] Each 1127.00
CTO004 P- 68 / 12 Supplying, fitting and fixing cast iron raised rain proof
tank cover 500 mm dia. with locking arrangements
(weighing not less than 12 kg). [ P- 34 / 7 ]
Each 1182.00
CTR005 P- 76 / 21 Cleaning and removing mud over 2000 litre Water tank
including masonry reservoir. [ P- 36 / 13 ] Cum 42.00
CTR013 (iv) Angle back wash basin 400 mm X 400 mm size Each 1752.00
BSO015 (a) (ii) C.P Piller cock Super Deluxe with Aerator - 15
mm (Equivalent to Code No-508 & Model - TROPICAL /
SUMTHING SPECIAL of ESSCO or similar brand).
Each 617.00
PPR007
(iii) 80 mm dia. boring etc. beyond 150 metre Mtr. 174.00
PPR008
(c) For depth upto 150 metre for 40 mm dia. Tube
well with top enlargement of 80 mm dia.
PPR009
(i) 40 mm dia. boring etc. Mtr. 119.00
P- 104 / 2 Labour for boring through any type of soil for sinking
tube well of required dia. with top enlargement by rig
boring system (either by reserve circulation or by direct
rotary method) including hire charges and labour for rig
machine, tools and plants, staging, force pumping set
and making arrangement for water required for boring
etc. complete and lowering of pipes, strainers, blind
pipes etc. complete. [ P- 47 / 2 ]
(a) For depth upto 250 metre for 100 mm dia. Tube
well with top enlargement of 200 mm dia.(upto 50
metre).
PPR011
(i) First 50 metre Mtr. 894.00
Page 183 of 338
(b) For depth upto 250 metre for 150 mm dia. Tube
well with top enlargement of 250 mm dia.(upto 50
metre).
(c) For depth upto 250 metre for 150 mm dia. Tube
well with top enlargement of 300 mm dia.(upto 50
metre).
P- 108 / 5 Supplying G.I. pipe strainer with brass net & jacketted
of approved quality. (Heavy Type). [ P- 48 / 4 ]
P- 110 / 9 Supplying, fitting and fixing steel cutter piece upto 450
mm long with sockets. [ P- 49 / 8 ]
TWO007 P- 112 / 14 Supplying, fitting and fixing popular Maya pump no. 6 or
similar. [ P- 50 / 13 ]
(c) For additional period beyond 3(three) days. Per Day 4959.00
TWR001 P- 120 / 3 Supplying, fitting and fixing C.I. cover for street pattern
hydrant. [ P- 55 / 3 ] Each 684.00
P- 122 / 9 Dismantling fire hydrant after plugging off the supply for
repairs and refixing the same including taking to
workshop and back. [ P- 56 / 9 ]
Each 301.00
P- 122 / 10 Renewing bolt and nut for hydrant. [ P- 56/ 10 ] Each 10.00
HAO002
(a) With valamoid joints including sealing with sand
cement morter (4:1) upto quarter depth.
HAO003
(i) 150 mm dia. (internal) Mtr. 1204.00
HAO004
(ii) 100 mm dia. (internal) Mtr. 712.00
HAR017
(a) With valamoid joints including sealing the top
with cement mortar (4:1)
P- 136 / 8 (a) H.C.I. bell mouth plain trap supplied,fitted and fixed
with lead jointing complete 100 mm dia. and painting
two coats to the exposed surface approved paint
complete. (payment of painting will however be paid
seperately). [ P- 61 / 8 ]
Each 789.00
P- 136 / 11 Supplying, fitting and fixing Cast Iron Fresh air inlet
valve 100 mm.and painting two coats to the exposed
surface approved paint complete. (payment of painting
will however be paid seperately). [ P- 61 / 11 ]
Each 180.00
(a)
P- 144 / 23 Cast Iron fittings for soil pipe line conforming to I.S.
1729/1970 including jointing and fitting and fixing in
position and painting two coats to the exposed surface
complete including cost of all materials & labour.
(payment of painting will be paid seperately).
[ P- 65 / 22 ]
SPF016 (i) With valamoid joint including sealing the top with
cement mortar (4:1) Each 1459.00
N.B. For any junction without door the rate for above
items will be reduced by Rs. 50.00
75 mm Mtr. 205.00
75 mm Mtr. 221.00
75 mm Mtr. 227.00
SPF019
110 mm Mtr. 344.00
75 mm Mtr. 238.00
75 mm Mtr. 246.00
SPF020
110 mm Mtr. 353.00
75 mm Mtr. 256.00
SPF021
110 mm Mtr. 366.00
SPF022
Fittings.
a) Coupler
(i) 75 mm Each. 48.00
b) Plain Tee
c) Door Tee
e) Plain Y
P-68 g) Double Y
I) Bend 45°
j) Bend 87.5°
m) Cross Tee
p) Pipe Clip
xxix) Passover
75 mm Each. 301.00
75 mm Each. 98.00
Door Gasket
75 mm Each. 6.00
Rubber Ring
75 mm Each. 14.00
P- 150 / 4 Renewing lead caulked joints for H.C.I. pipe with new
gaskets. [ P- 73 / 4 ]
P- 150 / 5 Renewing cast iron inspection door with bolts and nuts
complete for fittings of 50 mm dia. to 150 mm dia.
H.C.I. pipe. [ P- 73 / 5 ] Each 64.00
P- 154 / 2
N.B. For W.C. with trap without vent the rate will be
reduced by Rs. 25.00
Page 208 of 338
P- 154 / 6 Supplying, fitting and fixing Flat back urinal (half stall
urinal) in white vitreous chinaware of approved make
in position with brass screws on 75 mm X 75 mm X 75
mm wooden blocks complete.[ P- 75 / 5 ]
P- 156 / 9 Supplying, fitting and fixing Foot rest for water closet of
size 275 mm X 125 mm with :- [ P- 76 / 8 ]
(a) E.W.C.
P- 158 / 12
(a) C.P. urinal flush pipe fittings range of one Each 448.00
(b) C.P. urinal flush pipe fittings range of two Each 1043.00
Page 210 of 338
(c) C.P. urinal flush pipe fittings range of three Each 1459.00
P- 160 / 22 Supplying, fitting and fixing towel rail with two brackets.
[ P- 78 / 21 ]
(b) Aluminium
(a) With 250 mm thick dry brick work and 250 mm thick
cement brick work (4:1) and 1.00 m.inside dia. Each
SPR006
(i) 35 MT load bearing capacity round manhole cover
provided with two lifter hooks fitted with matching frame
of size Each
SPR007
Cover: 700 mm X 100 mm
SPR008 Frame: 900 mm X 185 mm
Weight: 250 kg (approx)
SPR009
(ii) 25 MT load bearing capacity round manhole cover
provided with two lifter hooks fitted with matching frame
of size Each
Cover: 600 mm X 75 mm
SPR010 Frame: 750 mm X 150 mm
Weight: 140 kg (approx)
(a) Round
(b) Square
P- 178 / 5
(C)-(I) MISCELLANEOUS :-
W.C.II
Page 220 of 338
P- 180 / 2 Cutting out asphaltum road and restoring the same with
spoils including guarding and barricading. [ P- Mtr. 18.00
93 / 2 ]
P- 180 / 3 Cutting trench upto 1.00 metre deep through masonry
foundation. [ P- 93 / 3 ] Mtr. 48.00
WCO012
(i) Upto 100 mm dia. pipe Mtr. 43.00
(ii) Above 100 mm dia. and upto 200 mm dia. pipe Mtr. 58.00
(iii) Above 200 mm dia. and upto 300 mm dia. pipe Mtr. 85.00
WCO013
(iv) Above 300 mm dia pipe
Mtr. 140.00
P- 182 / 17 Dismantling ball cock and refixing the same after repair
including straightening lever and renewing split pin.
[ P- 94 / 17 ]
WCO014
(i) 15 mm Each 19.00
(b) 20 mm dia.
(c) 25 mm dia.
(e) 40 mm dia.
WCR027
(i) Light quality Mtr. 260.00
WCR028
(ii) Medium quality Mtr. 270.00
(f) 50 mm dia.
(g) 65 mm dia.
(h) 80 mm dia.
MIS001 P- 196 / 8 Supply of G.I. plain tee of approved brand and make.
[ P- 100 / 8 ]
N.B. The rates for supply of non TATA but I.S.I. marked
G.I. pipes and fittings will be arrived at by reducing the
corresponding rates for TATA pipes and fittings by 20%.
Hoog
P- 106 / 1 Plumbing mistry Each 200.00
COM003
COM004
Page 233 of 338
COM005
COM006
COM007
Page 234 of 338
COM008
COM009
COM010
Page 235 of 338
COM011
COM012
Page 236 of 338
COM013
COM014
COM015
Page 237 of 338
COM016
COM017
Page 238 of 338
WVC001
WVC002
WVC003
WVC004
WVC005
WVC006
Page 239 of 338
Remarks
811.00
512.00
389.00
389.00
728.00
459.00
348.00
335.00
674.00
406.00
275.00
261.00
25.00
Page 240 of 338
42.00
Remarks
Page 241 of 338
OK
Page 242 of 338
147.00
Page 243 of 338
29984.38
39712.61
51280.80
74921.87
95426.49
149479.75
Page 244 of 338
13058.22
143.00
737.17
234.00
Page 245 of 338
308.00
4570.00
3806.00
3471.00
2803.00
2803.00
2857.00
Page 246 of 338
1407.00
1032.00
1876.00
349.00
1732.00
2066.00
3908.00
5898.00
1383.00
3940.00
2906.00
3946.00
1677.00
2136.00
Page 247 of 338
3359.00
Page 248 of 338
Supplied by Contractor
P. No. / It. No.Description of Item
Unit Rate Remarks
EMBANKMENT WORKS
P- 113 / 4 Extra for carriage of all kinds of soil for each additioal unit lead of
50 m. (or part thereof) beyond the initial unit lead of 50 m. upto
total lead of 150 m. including & unloading. cu.m. 3.50
P- 113 / 5 Extra for carriage of all kinds of soil for each additioal unit lead of
50 m. (or part thereof) beyond 150 m. but upto 500 m. including
loading and unloading. cu.m. 4.20
P- 113 / 6 Extra for each additional unit lift of 1.5 m. (or part thereof) beyond
the initial unit lift of 1.5 m. cu.m. 2.80
P- 113 / 7 Earthwork in cutting to form road section in correct profile in For ites No.
ordinary soil including removal of spoils not exceeding initial lead of 1 to 6 and
50 m. and initial lift of 1.5 m. 11 to 17 &
cu.m. 22.00
19 Cost
should be
P- 113 / 8 Earthwork in cutting to form road section in correct profile in mixed evaluated
soil including removal of spoils not exceeding initial lead of 50 m. considering
and initial lift of 1.5 m. in mixed soil (i.e. clay mixed with kankar, 100 cu.m.
pebbles, moorum etc.) cu.m. 25.00 borrowpit
earth = 115
cu.m.
P- 114 / 9 Earthwork in cutting to form road section in correct profile in mixed embankmen
hard soil (I.w.d hard moorum and soil containing laterite and t earth.
boulders which do not require blasting) including removal of spoils
not exceeding initial lead of 50 m. and initial lift of 1.5 m. in mixed
soil complete. cu.m. 30.00
P- 114 / 12 Earthwork in embankment in mixed soil (i.e clay mixed with kankar
pebles, moorum), to correct profile as per desired formation level Rates to be
with earth obtained from land owned or arranged by the deptt. specified by
depositing in layers of 250 mm. thickness including breaking clods, the
dressing etc. complete as per specification , drawing and direction Engineer -
of Engineer - in Charge (Payment will be made in cu.m. on the in - Charge
basis of quantity arrived at on pre-work and post work level section considering
measurements). Item No. 1
to 9 given
cu.m. before.
P- 114 / 13 Earthwork in embankment in mixed hard soil (i.e hard moorum and
soil containing laterite and bouldens which do not require blasting),
to correct profile as per desired formation level with earth obtained
from land owned or arranged by the deptt. depositing in layers of
250 mm. thickness including breaking clods, dressing etc. complete
as per specification , drawing and direction of Engineer - in Charge
(Payment will be made in cu.m. on the basis of quantity arrived at
on pre-work and post work level section measurements).
cu.m.
cu.m.
N.B.
To arrive the rate for land owned / arranged by the contractor add
Rs. 5.00 per cu.m. extra over corresponding items of E/W for the
lands owned / arranged by the Deptt. This is applicable for all items
of Earth Work where land is owned and arranged by contractor.
a) With 50 m. lead and 1.5 m. lift from road side land in ordinary
soil. cu.m.
b) With 50 m. lead and 1.5 m. lift from road side land in mixed soil.
cu.m.
c) With 50 m. lead and 1.5 m. lift from road side land in mixed hard
soil. cu.m.
d) With carried earth, land arranged by the contractor. cu.m.
P- 117 / 24 Extra cost for removal of spoils for each additional unit lift of 1.5 m.
(or part thereof) beyond the initial lift of 1.5 m. cu.m. 2.60
P- 117 / 26 Clearing and removing mixed slip of (Earth mixed with moorum,
kankar, pebbles, Rocks boulders etc.).
a) Removal of Spoils on the khad side. cu.m. 13.50
b) Removal of Spoils within a lead of 50 m. cu.m. 22.00
P- 117 / 27 Extra cost for removal of spoils or earth slip or mixed skip for each
additional unit lead of 50 m. (or part thereof) beyond the initial unit
lead of 50 m. upto a total lead of 200 m. cu.m. 2.80
P- 117 / 28 Turfing with grass sods 5 cms. To 8 cms. Thick (Turf to be arranged
by the contractor at no extra cost) including watering and
maintaining till the grass is fully grown.
(i) Turf obtained from any distance upto 500 m. cu.m. 5.30
(ii) Turf obtained beyond 500 m. upto 1 KM distance. cu.m. 6.30
P- 117 / 30 Cutting kutcha drain of 60 cm. Wide and depth upto 30 cm.
Through ordinary soil m. 2.80
P- 118 / 32 Cutting kutcha drain of 60 cm. Wide and depth upto 30 cm.
Through hard rock. m. 11.00
P- 118 / 38 Cutting & removing stumps of trees including cutting roots girth at
breast height 90 cm. each 40.00
P- 118 / 39 Cutting & removing stumps of trees including cutting roots girth at
breast height above 90 cm. upto 150 cm. each 70.00
P- 118 / 40 Cutting & removing stumps of trees including cutting roots girth at
breast height above 150 cm. upto 275 cm. each 100.00
P- 118 / 41 Cutting & removing stumps of trees including cutting roots girth at
breast height above 275 cm. upto 375 cm. each 130.00
P- 118 / 42 Cutting & removing stumps of trees including cutting roots girth at
breast height above 375 cm. upto 475 cm. each 170.00
P- 121 / 3 Spreading moorum 80% and sand 20% by volume to the required
thickness in layers as specified and directed bby the E-in-C
stabilising the same by adding requisite quantity of water to get
optimum moisture content remixing wet, wet rolling to required
compacted thickness to proper grade, camber and super elevation
with power roller including proper tampering and curing the same
for 5 days to have maximumdry density as specified and lighting,
guarding, barricading and making earthen bundhs for protecting
the edges etc. all complete as per specification(The payment is to
be made on the basis of the finished compacted volume).
cu.m. 80.00
N.B. : Labour rate / cu.m. is provided, cost of moorum and sand to
be added to arrive at the consolidated rate (compaction factor is
0.70).
cu.m. 64.00
N.B. : Labour rate / cu.m. is provided, cost of moorum is to be
added to arrive at the consolidated rate (compaction factor is 0.67).
cu.m. 62.00
N.B. : Labour rate / cu.m. is provided, cost of river bed materials is
to be added to arrive at the consolidated rate (compaction factor is
0.70).
Page- 122 / Labour for Spreading river-bed materials in layers as per direction
Sl. No. 7 of E-in-C. cu.m. 18.00
Pe- 122 / 8 Spreading and compacting sand to required thickness, in layers not
exceeding 15 cm. To proper gradient and camber inundating each
layer by water and packing and ramming layer by layer to achieve
desired compaction excluding cost of sand but including lighting,
guarding, barricading and making earthen bundh where necessary
curing with water as per direction mending cracks and depressions
by ramming when necessary (Payment will be made on the basis
of finished compacted volume).
cu.m. 28.00
N.B. : Labour rate / cu.m. is provided, cost of sand is to be added
to arrive at the consolidated rate (compaction factor of dry clean
sand is 0.835). Suitable consideration should be made for bulkage
of sand).
P- 122 / 9 Spreading and consolidating stone dust to a depth of 100 mm. and
above at desired density with power roller to proper gradient and
camber including watering as necessary lighting, barricading,
guarding and making earthen bundh where necessary to protect
the edges and curing with water 2 to 3 days mending cracks or
depression by rolling where necessary complete as per
specification. All incidental charges of roller inclusive of cost of
fuels and lubricants are included (payment will be made on basis of
finished compacted volume of stone dust).
cu.m. 61.00
N.B. : Labour rate / cu.m. is provided, cost of sand is to be added
to arrive at the consolidated rate (compaction factor is 0.70).
cu.m. 28.00
N.B. : Labour rate / cu.m. is provided, cost of stone dust and sand
is to be added to arrive at the consolidated rate (compaction factor
is 0.67).
P- 125 / 1 Mobilasation charges of all tools and plants along with accessories,
materials, labour, supervision etc. at site of work - required in
connection with boring and testing work including setting up boring
rig and shifting to different borehole points etc. etc. and also
including withdrawal of the same from the site after completion of
work, complete as per direction of E-in-C. (Payment will be made
after successful completion of work).
P- 125 / 2 Carriage of all disturbed and undisturbed samples from site of work
to the divisional office or elsewhere including loading and unloading
asper direction of E-in-C. LS. 1,265.00 1,265.00
Detailed Investigation :
Some samples are to be kept at sub-div. Office for additional
testing by the E-in-C.
SITE INVESTIGATION.
P- 125 / 4 Conducting plate load test over cohesive and noncohesive soils of
very soft to very stiff / very loose to dense by making pit of required
stie at foundation level (Depth not greater than 1.5 m.) providing
necessary platform for loading, plates, jacks, datum bars, dial
gauges, magnetic boxes, loadingmaterials (Gunny bags filled with
sand) and labours, supervisor etc. all complete to perform the
same including shifting the same to other point after the test. As
per IS 1988 - 1982 reaffirmed 1988.
i) For evaluation of bearing capacity and settlement. Per Test 7,000.00 7,000.00
P- 127 / 5 Labour for boring by sinking and finally withdrawing 50 mm. to 1--
dia (internal) pipe by a standard method to any depth below ground
level / bed level in all types of soil like clay, silt, sand stiff clay ,
mixed soil etc. except rock including collection of disturbed soil
samples and including preparation and submission of bolog as per
standard proforma and also including hire charges of tools and
plants complete aas per direction of E-in-C. (Payment will be made
on the length driven into the ground)
Preliminary Investigation ;
(a) Depth 0 m. to 30 m. __________________________. m. 20.00
(b) Depth greater than 30 m. and upto 60 m. ______________ m. 27.00
© Extra for boring in water (1.2 m. and higher depth). LS 650.00
Page- 127 / Labour for making boreholes of 150 mm. to 250 mm. dia. By any
Sl. No. 6 standard method to any depth below ground level / bed level in all
kindls of soil like clay, silt , sand, dtiff clay, mixded soil etc. except
rock (for the purpose of collecting disturbed and undisturbed soil
samples, conducting standard penetration tests at suitable intervals
etc. ) including preparation and sub-mission of bore log as per
IRC : 75 and 78 and C.I. 2400 of specifications for Road and
Bridge works published by IRC and also including hire charges of
tools and plants complete as per direction of E-in-C. (Payment iwll
be made on thelength driven into the ground).
(i) When causing pipe is used to prevent collapse of bore - hole
(casing pipe to be finally withdrawn).
(a) Depth 0 to 10 m. m. 275.00
(b) Depth greater than 10 m. and upto 20 m. m. 330.00
© Depth greater than 20 m. and upto 30 m. m. 385.00
(d) Depth greater than 30 m. and upto 40 m. m. 440.00
(e) Depth greater than 40 m. and upto 50 m. m. 500.00
(f) Depth greater than 50 m. and upto 60 m. m. 575.00
(ii) When drilling mud "Benotonite of Suitable consistency" is used
to prevent collapseof bore hole.
P- 127 / 7 Labour for collecting disturbed sample upto any depth -each
sample shall weigh 500 gms. (approx.) including keeping in
polythene / plastic / tin container labelling, packing etc. and also
including hire charges of tools and plants complete as per direction
of E-in-C.
Each 40.00
Detailed Investigation.
Each 44.00
Detailed Investigation.
P- 129 / 10 Labour for conducting Situ Vane Shear test for soil, in the bore hole
already made at intervals of 3m. , 2m. And 1.5 m. as required upto
any de4pth in very soft to soft, soil mediu, to stiff soil including
keeping all records and submission of results in prescribed
proforma and also including hire charges of tools and plants
complete as per direction of the E-in-C as per IS 4434 for
Detailed Investigation.
i) For very soft to soft clay using 100 mm. dia. Vane. Each 220.00
ii) For medium stiff clay using 75 mm. dia. Vane. Each 275.00
A. Preliminary Investigation :
I. Disturbed Samples.
a) Liquid limit & plastic limit as per IS 2720 Pt. V (On 50% of
samples collected) from each bore hole. Each 35.00
b) Sieve Analysis as per IS 2720 Pt. IV (On 25% of samples
collected) from each bore hole. Each 22.00
B. Detailed Investigation.
a) Liquid limit & plastic limit as per IS 2720V (On 50% of samples
collected) from each bore hole. Each 36.00
b) Sieve Analysis as per IS 2720 Pt. IV (On 25% of samples
collected) from each bore hole. Each 22.00
c) Hydrometer Analysis as per IS 2720 Pt. IV (On 20% of samples
collected). Each 66.00
d) Natural Moisture Content and Dry Density as per IS 2720 Pt. II
(On 100% of Samples collected). Each 22.00
e) Specific Gravity as per IS 2702 Pt. III (On 20% of samples
collected) Each 22.00
f) Direct Shear as per IS 2702 Pt. XIII (On 5% of samples collected)
Each 120.00
g) Unconfined Compression as per IS 2702 Pt. XIII (On 80% of
samples collected)
i) Undisturbed Each 33.00
ii) Remoulded Each 36.00
Test On Rocks.
Earthwork
Cu.m. 33.50
Cu.m. 36.00
a) Add extra for each additional 1 m. depth of excavation beyond
initial 3 m. excatation excluding hire and labour for shoring.
Cu.m. 4.30
Cu.m. 38.00
This item should be executed on specific direction of E-in-C.
P- 135 / 6 Add extra for excavation in stoney and moorum soil. Cu.m. 7.00
Shuttering.
P- 136 / 10 Providing form work and staging inclduing hire and labour charge
all complete for slabs of culvert and cross-drain upto 3 m. clear
span inclluding stripping off and removing after completion of work
as per specification and direction,
a) Form work so as to give smooth concrete finish with timber plank
not less than 38 mm. thick. Sq.m. 225.00
b) Extra over the rate of (a) above for form work with plywood of
quality as stipulated in IS:4990 instead of plank so as to give fine
finish. Sq.m. 2.50
c) Extra over the rate of (a) above for form work with steel sheet
plate instead of plank so as to ensure fine finish. Sq.m. 3.50
P- 136 / 11 Providing form work and staging inclduing hire and labour charges
for the same as required for foundation concrete wroks of depth not
exceeding 500 mm. and for concrete works in vertical faces of
parapet curb, road curb, cable tray, cable tray cover, rail post so as
to give good concrete finish including stripping off and removing
after completion of work as per specification. For bridges of length
upto 30.00 m.
Sq.m. 80.00
P- 136 / 12 Providing form work for soffits of slabs / beam (above 3 m. clear
span) of culverts and bridges (Major and Minor) and box culverts
including hire and labour charges for the same stripping off and
removing after completion of works as per specification but
excluding staging.
III. Form work with steel plate instead of plank so as to ensure fine
finish. Extra over the corresponding rate of 12(1) (a) , (b) (c) , (d)
above. Sq.m. 3.50
P- 137 / 13 Providing form work and staging inclduing hire and labour charges
for the same for vertical walls and top slab of hollow super structure
of bridges so as to give fine finish including stripping off and
removing clearing on completion (for bottom slab of such stucture,
payment will be made as per preceeding items, including hire
charges of props and runners complete.
Sq.m. 235.00
Note : If timber shuttering is used, it should be lined with steel
plates.
P - 137 / 14 Providing form work and staging inclduing hire and labour charges
for the same for prestressed concrete girders, slabs or in any other
member of a bridge with steel section of best quality timber planks
of 45 mm. thick with steel lining or of ply wood as approved by E-in-
C so as to give fine finish and with props and concrete pedestals
including stripping off and removing after completion as per
direction of E-in-C.
Sq.m. 345.00
P- 137 / 15 Providing form work & staging inclduing hire and labour charges
for the same for prestressed concrete box girders of bridge by
cantilever construction with steel gantry in segmental construction
and including hanging arrnagement of H.T. Strand / Cable,
shuttering with steel section or best quality timber planks of 45 mm.
thick with steel lining or slipform shutter as approved by E-in-C so
as to give fine finish with props and other accessories etc.
inlcluding stripping off and removing the gantry after completion
and filling holes as per direction of E-in-C.
Sq.m. 860.00
P - 136 / 16 Hire & Labour charges for staging with salbullah for super structure
of briodge (Major and Minor) including stripping off and removing
clearing on completion of work as per design and drawing
approved by the E-in-C.
i) With driving of salbullah piling and taking out of the same after
stripping off the staging. Cu.m. 330.00
ii) Without Salballah driving but founding on sleeper base on
completed bed. Cu.m. 235.00
Note : Regarding volume measurement and rate of staging :-
1. For the purpose of length the distance between the two
transverse vertical planes through the centre of bearing of
abutment and articulation of articulation and pier or two piers or
between abutment and piers or two articulations will be considered
as the case may be, but the volume of piers or verticals intercepted
within the calculation should be deducted.
a) Bottom level.
Average bed surface of the river / channel or the gound surface as
specifeid between the inner surfaces of two abutments / end
supports of superstructue as the case may be.
i) Average R.L. of bottom of launched pre-cast P.S.C. girders for
deck slab of such bridge.
b) Top level :
i) For portion of footpath with railing etc. its average * botom level
should be considered.
ii) The bottom level of deck portion.
P - 140 / 17 Hire & Labour charges for staging for super structure of bridge with
tybular steel pipe (TATA or equivalent) Conforming to IS : 11239
(Part - I & II) consisting of H-Frame (2 . X 1 m.) made of 40 mm.
NB (Heavy) pipe and horizontal and diagonal bracing with 40 mm.
NB (Medium) pipe including necessary, clamping arrangement of
approved make etc. complete as per design and drawings and
direction of the E-in-C including releasing and dismantling and
removing and clearing the site on completion of work.
P - 140 / 18 Providing for work and staging including hire and labour charges
for the same for bridges of length above 30.00 m.
The rates for shuttering for open foundation of depth above 500
mm. well steining and well curb shall be as per 18 (a) above. The
heights for piers, autments, retaining walls shall be measured from
the bottom of their shaft portions. The heights for walls of box
bridge, vertical faces of supperstructure shall be measured from
their bottom, 50% will be added to the above rate for the shuttering
for special ornamental concrete.
Page- 142 / Fabrication, erecting and laying steel cutting edge for well curb
Sl. No. 20 including cost & Carriage of alll materials as per drawing, technical
specification and direction of E-in-C.
Kg. 40.00
per MT 725.00
(One cu.m. of girder shall be considered to weigh 2.5 MT. Including
reinforcements. H.T. Cables and other components and fixtures).
P - 143 / 23 Laying layer of brick flat soling in foundation with picked Jhama or
1st Class Bricks incluing ramming and dressing bed to proper level
and grade filling up all joints with local sand and cost & carriage of
all materials. The cost of sand is included but not cost of bricks (for
B.F.S. add cost of bricks).
P - 143 / 24 First class brick work in cement sand mortar in steining of well,pier,
abutment, wing wall, parapets cross drain . H.P. Culverts, guard
wall etc. etc. including curing, scaffolding, raking out joints etc. etc.
complete and cost andcarriage of all materials.
P - 143 / 25 Extra labour for First Class Brick work in arches including hire
charges of shuttering.
i) Upto 1.5 m. span Sq.m. 65.00 65.00
i) Upto 4.5 m. span Cu.m. 75.00 75.00
i) Upto 6 m. span Cu.m. 90.00 90.00
P - 145 / 27 Rute pointing to brick work in sand and cement mortar (3:1)
including raking out joints, curing and cost and carriage of all
material.
Sq.m. 27.00 26.50
P- 145 / 29 String Course upto 75 mm. projection and upto 150 mm. depty
cement plastered (4;1) (including stripping off old surface -where
necessary) complete. Sq.m. 44.00 42.50
P- 145 / 30 a) Supplying, fitting and fixing precast neat cement finished R.C.
hand rails having cross sectional area not more than 200 CM2 as
per drawing and specification with cone mix in M30 concrete with
excellent concrete finish with casting on a vibratory platform with
proper cover as per direction of E-in-C.
m. 214.00 213.00
b) Supplying, fitting and fixing precast neat cement finished R.C.
hand rails having cross sectional area not more than 200 C sq.m.
as per drawing and specification with cross sectional area more
than 200 C sq.m. m. 290.00 289.00
b) Providing and laying M20 design mix conc in bottom plug with
tremie pipe method graded stone chips / gravel / bazrees of
approved size including cleaning & screening of C.A. & Coarse
sand and carriage of all materials and including cost of 10% extra
cement. The slump of conc. should be about 150 mm.
c) Providing and laying M25 design mix conc in bottom plug with
tremie pipe method graded stone chips / gravel / bazrees of
approved size including cleaning & screening of C.A. & Coarse
sand and carriage of all materials and including cost of 10% extra
cement. The slump of conc. should be about 150 mm.
P- 147 / 34 Providing and laying Cement Concrete (1:1 1/2 : 3) with or without
reinforcement in any part of bridges and culverts with graded stone
chips / gravel / bazree of appropriate nominal size inclduing
screening and cleaning of approved coarse aggregates and sand
cu.m. 2160.00 2140.00
as necessary, curring in water, with cost carriage of all materials,
Note : (i) (Construction
but excluding wing is and
cost of labour to add cost andfor
materials carriage of coarse
shuttering and
aggregates only to arrive at consolidated rate).
reinforcement.
(ii) While actually providing the item in estimate / agreement
for work maximum nominal size of the coarse aggregate intended
to be used may be selected and mentioned in the item.
Page- 149 / Providing and laying M-15 design mix concrete for reinforced
Sl. No. 36 concrete work with coarse aggregates of appropriate nominal size
and grading, fine aggregate (sand) conforming to proper grading
zone, both of approved quality and cement as necessary including
labour, cost and carriage of all materials and including preparation
of design mix approval of the same by the E0in -C and cost for
quality control , sampling, testing etc. all complete but excluding
formwork and reinforcement.
P- 151 / 37 Providing and laying M-20 design mix concrete for reinforced
concrete work with coarse aggregates of appropriate nominal size
and grading, fine aggregate (sand) conforming to proper grading
zone, both of approved quality and cement as necessary including
labour, cost and carriage of all materials and including preparation
of design mix approval of the same by the E0in -C and cost for
quality control , sampling, testing etc. all complete but excluding
formwork and reinforcement.
P- 151 / 39 Providing and laying M-30 design mix concrete for reinforced
concrete work with coarse aggregates of appropriate nominal size
and grading, fine aggregate (sand) conforming to proper grading
zone, both of approved quality and cement as necessary including
labour, cost and carriage of all materials and including preparation
of design mix approval of the same by the E0in -C and cost for
quality control , sampling, testing etc. all complete but excluding
formwork and reinforcement, H.T Cables and ducts.
P- 151 / 40 Providing and laying M-35 design mix concrete for reinforced
concrete work with coarse aggregates of appropriate nominal size
and grading, fine aggregate (sand) conforming to proper grading
zone, both of approved quality and cement as necessary including
labour, cost and carriage of all materials and including preparation
of design mix approval of the same by the E0in -C and cost for
quality control , sampling, testing etc. all complete but excluding
formwork and reinforcement, H.T Cables and ducts.
P- 153 / 42 Providing and laying M-45 design mix concrete for reinforced
concrete work with coarse aggregates of appropriate nominal size
and grading, fine aggregate (sand) conforming to proper grading
zone, both of approved quality and cement as necessary including
labour, cost and carriage of all materials and including preparation
of design mix approval of the same by the E0in -C and cost for
quality control , sampling, testing etc. all complete but excluding
formwork and reinforcement, H.T Cables and ducts.
Note : (A) For prestressed concrete bridge the rate for Item No. 41
and 42 to be enhanced by 5%. (Excluding the cost of course
aggregate)
(B) (i) When the total length of the bridge (prestressed and
R.C.C.) is above 60.00 m. between centre line of bearing of two
abutments / end piers , the rates of item nos. 33 (b) / 33 (c) and 37
to 42 to be enhanced by 2%.( Excluding the cost of course
aggregate)
(ii) In case of bridges of length above 200.00 m.
Enhancement rate will be by 5%.( Excluding the cost of course
aggregate) on the aforesaid items.
Expansion Joints.
P-159 / 57 Providing Weep holes (150 x 75mm.) in abutment or wing wall for
the entire thickness with slop 1 : 20 towards drainage surface
including packing different size of brick bats or boulders of
approved quality and size at the back side as per direction of
E.I.C.
Each 75.00
P-159 / 58 Sinking lugs of R.C.C. Box type bridges (for width of the box 7.5
metres and above) as per specification from the level of the bottom
lugs to the top of floor slab).
(I) Depth from 0m to 3m.
(a) Clear span noteceeding 4.5 metres Mtr 2,135.00
(b) Clear span exceeding 4.5 netres Mtr 2,150.00
(ii) Double Unit.
(a) Clear Span notexceeding 4.5 metres Mtr 4,140.00
(b) Clear span exceeding 4.5 metres Mtr 5,180.00
(iii)
(a) Mtr 6,150.00
(b) Mtr 7,160.00
(Width less than 7.5 metres proportionate deduction will be made).
P-160 / 60 Drilling Holes upto 15cm. Dia & upto 1.5m. Depth throughout
including bailing out/pumping out water and fitting/fixing anchor-
bolts 20 mm. To 40 mm. Dia with necessary fittings with cement
concrete 1:11/2 :3 and as directed by Engineer-in-charge including
cost all materials Mtr 220.00
P-160 / 61 Sand Fitting in wel pockets in layers duly compacted by inundation
with water including local carriages etc. Where sand is available
from the bed of the river (including royalty for the same)
P-163 / 63 Providing driven cast in situ R.C.C. piles of required diametre and
required length (length to be measured from the bottom of rate/Pile
Cap. To the bottom of shoe) as per drawing and specification
including cost of all materials and cost of labour for casting
hoisting, driving etc. and also including cost of dummy length of
pile and of hire charges of all instruments as necessary (cement
concrete should have an ultimate crushing strength of not less than
250 kg/cm2 on 15cm cube at 28 days and its cement concrete not
less than 400 kg/m3) but excluding the cost of reinforcement.
1,400.00
Use pakur variety or it's equivalent variety stone materials for
cement concrete. Ultimate crushing strength of cement conc.
Should not be less than 350 kg/cm2 with water cement ratio of 0.4
& slump 150 - 200 mm with minimum cement content of 400
kg/cum. The rate including the cost of 1 m. minimum dummy length
of pile concrete.
P-167/ Add additional cost over item no 64 & 65 for supply, fitting fixing
64(A) & 65 M.S. casing pipe over R.C.C. cast in situ bored pile of different
(A) diameter in position including cost of all materials complete as per
direction of the E.I.C.
(I) 6 mm thick casing
(a) 400 mm. Dia Mtr. 1,680.00 1,680.00
(b) 450 mm. Dia. Mtr. 1,890.00 1,890.00
(c) 500 mm. Dia. Mtr. 2,100.00 2,100.00
(d) 550 mm. Dia. Mtr. 2,320.00 2,320.00
(e) 600 mm. Dia. Mtr. 2,530.00 2,530.00
(f) 650 mm. Dia. Mtr. 2,740.00 2,740.00
(g) 700 mm. Dia. Mtr. 2,950.00 2,950.00
(h) 750 mm. Dia Mtr. 3,160.00 3,160.00
(I) 800 mm. Dia. Mtr. 3,370.00 3,370.00
(j) 1000 mm. Dia. Mtr. 4,220.00 4,220.00
(k) 1200 mm. Dia. Mtr. 5,060.00 5,060.00
P-169 / 66 Driving reinforced precast concrete piles with iron monkey including
hoisting, placing in position, supplying and fitting necessary pile
cap for protection of pile head against damages and staging as
necessary in all type of soil and as per IS specification.
Salbullah Piles :
P-171 / 70 (a) Supplying 10 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 110.00 101.00
(b) Supplying 12.5 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 150.00 144.00
(c) Supplying 15 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 230.00 222.00
(d) Supplying 17.5 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 320.00 314.00
(e) Supplying 20 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 480.00 461.00
(f) Supplying 22.5 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 605.00 578.00
(g) Supplying 25 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 776.00 739.00
(h) Supplying 28 cm. Dia. Salbullah piles at work site including
dressing and making one end pointed (Diametre of Bullah
measured at 1.5m. From thicker end). Mtr. 935.00 900.00
Eucalyptus Bullah
P-182 / 120 Labour for boulder pitching including hand packig and filling the
inter-stices with smaller variety of the same all complet. Sq.m. 57.00
REPAIR OF BRIDGE
P-189 / 1 (a) Supplying and laying road kerb and channel of approved
quality stone or precast cement concrete M25 with local stone of
size 100mm. X 250mm. (length of one piece not more than 1m.)
after preparing the bed by cutting or filling the existing road edge or
hard crust true to line, grade and slope as per specification and
direction of engineer-in-charge, including laying, at least 12mm.
thick sand cushioning below the flat piece and all and back filling
the vertical piece properly with earth duly compacted and curing
mortar joints for at least 3days complete including cost and Mtr. 205.00 195.00
carriage of all materials.
(b) Supplying and laying road kerb and channel of approved
quality stone or precast cement concrete M25 with local stone of
size 100mm. X 350mm. (length of one piece not more than 1m.)
after preparing the bed by cutting or filling the existing road edge or
hard crust true to line, grade and slope as per specification and
direction of engineer-in-charge, including laying, at least 12mm.
thick sand cushioning below the flat piece and all and back filling
the vertical piece properly with earth duly compacted and curing
mortar joints for at least 3days complete including cost and
carriage of all materials.
Mtr. 285.00 275.00
P-189 / 2. Labour for laying stone set pavement of 100 mm. Thick with
approved quality of stone sets of approx. size 100mm. X 125 mm.
X 250 mm. With top face dressed and other faces, fough dressed
laid over a layer of 12mm. Thick sand (local) cushioning on the
prepared base by necessary cutting or filling and rolling by power
roller after sprinkling of water placing the stone sets true to line,
level, grade and camber, keeping at least 8mm. wide spaces in
between the sets, filling up these space with sand cement mortar
4:1 or with sand and properly heated bitumen mixture so as fill up
these spaces properly and completely and to prevent any
movement of the stone sets, properly curing and lighting, guarding,
barricading etc. all complete including cost and carriages of all men
and machinaries and as per specification and direction of
Engineer-in-charge but excluding the cost of stone sets.
Cu.m. 90.00
(The payment is to be made on the basis of loose net volume of
bats in stacks).
N.B. This item of work should be adopted for the bottom most layer
only when the embankment is prepared by ordinary uncompacted
earth work.
P-194 / 15. Labour for spreading and consolidating 1st class brick bats/Jhama
metal/Laterite chelly or metal/shingle of specific size in hard crust
to requsite thickness (measured after compaction) in layers
including screening of bats/metals etc. as necessary, hand packing,
sweeping, watering and rolling in stages with power roller to proper
line, grade and camber, lightining, guarding & barricading and
making necessary earthen bundh of one metre width on each side
where necesary to protect edgs and preparing the bed by
necessary cutting or filling and rolling all complete including the
cost of all materials and hire and labour charges of all men and
mechineries and as per specification and direction of Engineer-in-
Charges (but excluding the cost of bats/chelly.)
(a) 127mm. To 152 mm. And 230 mm. To 254 mm. Deep edging
with stone boulders and with top portion rough dressed. Sq.m. 12.00
(b) 100 mm. Wide and 250 mm. Deep edging with stone sets laid
on edge. Sq.m. 10.60
P-198 / 24. Labour for taking out cracked, broken and damaged portion of
concrete road slabs of 7.5 cm. And above thickness after
dismantling picking up etc. removing to road side and stacking
within 50m. Sq.m. 8.00
P-199 / 25. Ornamental brick edging 75 mm. Wode in compound roads,
gardens etc. with 1st class bricks laid diagonally on end and with a
corner sightly raised from the adjoining surface thus giving a saw-
tooth appearance including cutting trench, laying brick and
repacking the trench throughly on both sides of the edging complte
as per direction excluding the cost of bricks.
Sq.m. 6.80
N.B. Labour rate per m. provided, cost of 5.5 nos. of bricks to be
included to arrive at the complete item rate.
P-199 / 26. Labour for taking out stone sets (size 100 mm. X 125 mm. X 250
mm.) from damaged pavement (in cement mortar) removing morter
from surface of the stone sets and stacking the stone sets as
directed within a lead of 75 m. % Nos 55.00
(Payment to be made on the number of stone taken out).
P-199 / 27. Spreading blindage for road topping (excluding the cost and
carriage of moorum/sand/kiln rubbish) in 6mm. Thick layer
including watering and rolling by power roller. Sq.m. 2.00
BITUMINOUS WORKS
200/2 Picking up and removing old bituminous layer or sand sealing coat
from black topped surface and cleaning the exposed surface by
scraping and stacking the material as directed.
Where thickness of layer is
(a) 25 mm. To 50 mm.
(b) 50mm to 100mm.
(c) Above 100 mm.
200/3. Repairing pot holes and making up small depressions with
ramming or poser rolling including screening, cleaning chips or
matals and washing drying as necessary and heating the chips or
metal where necessary cutting pot holes to rectrangular shape,
deeeping the edgs inclined towards the back, cleaning surface,
heating matrix and applying tack coat Iincluding edgs) 5 kg or 1 kg
of matrix/10m2 of road surface according as the road surface is an
old bituminous stage or WBM stage respectively and finishing the
top of repaired surface levelled with adjoining area including the
cost and carriage of stone materials and matrix and returning the
empty drum with bungs to the nearest Deptt. godown, including the
cost of tack coat.
212/18 [The rate provided is exclusive of the cost and carriage of stone
materials. Construction wings is to add the cost and carriage of
stone materials only to arrive at complete rate.
(a) On black top surface with out tack coat
(I) 50 mm Compacted thickness :
(ii) 75 mm. Compacted thickness :
(b) Extra over above corresponding rates sub head (a) on water
Boundh surface using tack coat @ 4 Kg/10m2
© Extra over above corresponding rates on black top surface when
tack coat is to be done @ 3 Kg/10m2
(ii) On old mlack top suface using matrix @ 3 Kg/10m2 in tack coat.
(ii) On old black surface using matrix @ 3 Kg/10m2 in the tack coat.
(ii) On old black surface using matrix @ 3 Kg/10m2 in the tack coat.
220/29 Laying liquid sela coat (Type 'A') with stone chips on old black top
surface including through cleaning of the surface apply uniformely
requisite quantity of hot bitumen @ 98 Kg per 100m2 and Blinding
the same with dry stone chips 6.7 mm. Size 100% passing through
11.2mm sieve and retained on 2.80 mm sieve @ 0.9 cu.m. per
100m2 of area with necesary rolling with matrix and stone chips,
heating the matrix, returning and empty drums to Departmentsl
godown and all other costs and carriage of aggregates only to
arrive at complete rate.]
220/30 Laying premixed seal coat (Type 'B') using 0.6 m3 of grit or sand
(passing 2.36 mm sieve and retained on 180 micrin) per 100 sp
metre area including cleaning the surface, preheating the Grit/Sand
by Miller Mixer/Suitable pans, Mixing the preheated grit/sand with
hot matrix @ 113.50 Kg per m3 of grit / and, laying the mixer
uniformly over he suraface and rolling with power roller including
heating matrix, and grit/sand all other costs and carriages in this
connection.
On Suitable Pan
(a) On Black topped surface with tack coat using matrix @
5Kg/10m2
(b) On Freshly laid premixed surface without tack coat.
By miller Mixer
(a) On Black topped surface with tack coat using matrix @
5Kg/10m2
(b) On Freshly laid premixed surface without tack coat.
225/39 Laying liquid sela coat (Type 'A') with stone chips on old black top
surface using xationic Bitumen emulsion (R.S. or M.S. grade)
conforming to IS:8887-1978 including Thorough cleaning the
surface applying emulsion @ 130 kg per 100m2 and blinding the
same with cleaned and wash stone chips 6.7 mm. Size 100%
passing through I.S.9.5. mm sieve and retained on I.S. 2.36 mm
sieve) by suitable means @ 0.6m3 per 100m2 and rolling with
power roller as per specification and direction of the Engg-in-
charge to all complete including cost of labour hire and running
charges of road roller and other tools and plants and cost of all
other incidental chatges including cost and carriage of stone chips
and emulsion and returning the empty drums to the Deptt.
godown/stack yeard.
(The rate .
I. Mixing by concrete mixer machine
II. Mixing by hand Operated Mixing Machine.
227/41 Laying stabilisation coat (with painting of matrix and spreading dry
medium sand over it) including thorough cleaning of the surface
including uprooting weeds, grass or small plants, laying of requisite
quantity of matrix (hot) spreading dry medium sand uniformly in
stages with total of 0.9 cu.m. per 100sq.m. including cost and
carriage of sand matrix heating matrix nd returning empty drums to
departmental godown and all others cost incidendal to the work.
MISCELLANEOUS WORK
P-231/1 Supply, fitting and fixing R.C. guard post 1.37 long with cement
concrete 1:2:4 with graded stone chips of 13.2 mm down casting,
curing complete including cost of providing 4 nos. of 12mm dia
M.S. rods of length 1.54m as main reinforcement and 6 nos. of
round shaped 6mm dia M.S.
(a) Pakur variety Stone Chipes Each 506.00 505.00
P-233/3 Supply, fitting and fixing rectangular 5th K.M. post/ K.M. post
(a) 5th K.M. post for NH, SH, & MDR
(i) Pakur variety Stone Chipes Each 1,322.00 1310.00
(i) When more than half the gabion as to be restored Each 288.00 280.00
P-237/8 Drum sheet walling 1.40 m (av.) high on salbullah pilling Mtr. 920.00 870.00
P-239/9 Drum sheet walling 1.40 m (av.) high on Eucalyptus pilling Mtr. 685.00 670.00
P-239/10 (a) Supply, fitting and fixing Sign board Each 1,982.00 1,975.00
(b) Supply, fitting and fixing route maker sign Each 1,040.00 1025.00
P-243/11 Labour for making 15 cm to 30 cm dia. Salbulla guard post Each 84.00
P-245/20 Painting
P-245/23 Making single drum ht. 0.9 m dia. Gabion Each 146.00
(a) With bamboos of length between 1.25 m to 2.00 m each Mtr. 288.00
(b) With bamboos of length between 2.00 m to 2.50 m each Mtr. 352.00
(c) With bamboos of length between 2.50 m to 3.00 m each Mtr. 476.00
(a) With bamboos of length between 1.25 m to 2.00 m each Mtr. 288.00
(b) With bamboos of length between 2.00 m to 2.50 m each Mtr. 354.00
(c) With bamboos of length between 2.50 m to 3.00 m each Mtr. 447.00
P-248/35 Labour for dismantling old wood work in bridges Sq.m. 155.00
(B) Painting with acrylic exterior surface finish as per item no 37(A)
etc. with Berger/ Asian paints Including supply, labour and
necessary scaffolding etc. for 2 coats of paint and one coat of
priming if necessary Sq.m. 40.00
P-250 / 4 Labour for carriage by head load for each additional 30.00 m. or
part there of beyond the initial 30.00 m. at the loading point or
unloading point where the trucks have nearer to access.
a) Cement in bags, tar or asphalt in drums and timber and similar
miscellaneius materials. MT 10.00
b) Steel materials. MT 16.50
c) Sand, cinder, lime moorum and similar material. Cu.m. 13.00
d) Bricks bats, boulders, stone materials, slag metals, stone chips,
gravels and shingles and similar materials. Cu.m. 16.50
e) Bricks. %0 Nos 25.50
f) Stone sets. %0 Nos 28.50
P-251 / 5 (A) Labour for unloading from truck and loading into boat at ferry
crossing where loaded trucks are not allowed to be ferried across
including carriage by head load with necessary lead and lift.
(B) Labour for unloading from boat and loading into truck at ferry
crossing where loaded trucks are not allowed to be ferried across
including carriage by head load with necessary lead and lift.
(C) Labour for loading into boat and unloading the same at the
opposite bank where loaded truck are not allowed to be ferried
across including carriage by head load with necessary lead and lift.
(D) Labour for loading into boat and unloading the same and
loading into truck at the oppsite bank or destination at ferry
crossing where loaded trucks are not allowed to be ferried across
including carriage by head load with necessary lead and lift.
P-253 / 6 Labour for loading R.C.C. pipe into truck at the lifting point,
unloading at destination and stacking properly in godown or yard
as directed including carriage by head load, lead upto 30.00 m. at
each of the two points.
P-253 / 7 Labour for carriage of R.C.C. pipe manually for each additional
30.00 m. or part there of beyond the initial 30.00 m. at the loading
or at the unloading point.
P-253 / 8 (A) Labour for unloading R.C.C. pipe from truck and loading into
boat at ferry crossing when loaded trucks are not allowed to be
ferried across including carriage by head load with necessary lead
and lift.
(B) Labour for unloading R.C.C. pipe from boat and loading into
trucks at ferry crossing when loaded trucks are not allowed to be
ferried across including carriage by head load with necessary lead
and lift.
Loading = 40.00%
Unloading = 35.00%
Stacking = 25.00%
B ROAD TRANSPORT
P-255 / 9 (a) Carriage of cement (in bags) tar or asphalt (in drums)
timber and similar miscellaneous materials over pucca road.
P-258 / 14 Carriage of R.C.C. pipes and collars 600 mm dia. Over pucca road.
The length of each collar will be taken as 0.30 m. of the
corresponding dia. Of pipe.
(i) Distance carried upto 5 K.M. Per Metre 34.00
(ii) Extra over the rate for 5 KM. carriage for every additional 1 km. Per Metre
(or part thereof) carriage beyond 5 KM. and upto 10 KM. 4.00
(iii) Extra over the rate for 10 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 10 KM. and upto 20 KM. 3.90
(iv) Extra over the rate for 20 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 20 KM. and upto 50 KM. 3.80
(v) Extra over the rate for 50 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 50 KM. and upto 100 KM. 3.70
(ii) Extra over the rate for 100 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 100 KM 3.40
P-258 / 15 Carriage of R.C.C. pipes and collars 900 mm dia. Over pucca road.
The length of each collar will be taken as 0.30 m. of the
corresponding dia. Of pipe.
(i) Distance carried upto 5 K.M. Per Metre 42.00
(ii) Extra over the rate for 5 KM. carriage for every additional 1 km. Per Metre
(or part thereof) carriage beyond 5 KM. and upto 10 KM. 5.00
(iii) Extra over the rate for 10 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 10 KM. and upto 20 KM. 4.90
(iv) Extra over the rate for 20 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 20 KM. and upto 50 KM. 4.80
(v) Extra over the rate for 50 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 50 KM. and upto 100 KM. 4.60
(ii) Extra over the rate for 100 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 100 KM 4.30
P-259 / 16 Carriage of R.C.C. pipes and collars 1200 mm dia. Over pucca
road. The length of each collar will be taken as 0.30 m. of the
corresponding dia. Of pipe.
(i) Distance carried upto 5 K.M. Per Metre 84.00
(ii) Extra over the rate for 5 KM. carriage for every additional 1 km. Per Metre
(or part thereof) carriage beyond 5 KM. and upto 10 KM. 11.00
(iii) Extra over the rate for 10 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 10 KM. and upto 20 KM. 9.80
(iv) Extra over the rate for 20 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 20 KM. and upto 50 KM. 9.70
(v) Extra over the rate for 50 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 50 KM. and upto 100 KM. 9.30
(ii) Extra over the rate for 100 KM. carriage for every additional 1 Per Metre
KM. (or part thereof) carriage beyond 100 KM 8.60
P-259 / 18 Carriage of Tar Boiler over pucca road including loading and Each per
unloading km 31.00
P-260 / 19 Carriage of Hand Mixing drum with stand over pucca road .
(a) When the stand is detachable from the drum Each per
km 12.00
(b) When the stand is fixed to the drum Each per
km 16.00
P-260 / 21 Carriage of Miller Mixer over pucca road including loading and Each per
unloading km 47.00
P-260 / 22 Carriage of Concrete Mixer over pucca road including loading and Each per
unloading km 31.00
P-260 / 24 Carriage of Boundary pillars, R.C. guard post, K..M. post etc. from
godown or stackyard to work site including loading unloading etc.
as per direction.
(a) 1 st. K.M. Each 6.00
(b) Subsequent per K.M. Each 2.00
NOTE :-
1.A. For carriage of 7M or longer unbent steel rounds the
contractor is required to arrange for trailer trucks for such purpose
or to make improved arragement. In expeptional case, the E.I.C.
may his discretion, permit bending double with large loop but in
that case the contractor shal have to do the looping and
straigthening the same back at the destination to the satisfaction of
the E.I.C. The contractor will be entited for these works to an
additional payment of Rs. 15/- per M.T. of steel rods.
8 Laterite ( at source)
[i. The rate provided is exclusive of tack coat. For tack coat refer
item no. 37, which must be executed to get the work done as a
whole and payment is to made seperately.
ii. The rate is also excluding the cost
and carriage of stone materials and bitumen which are to be added
to arrive at the complete rate]
P-23 / 4 (a) Labour for precoating stone aggregate with hot matrix @ 56 kg /
cu.m. of stone aggregate in concrete mixer including preheating
the stone aggregate at a suitable terperature including the cost of
carriage of the stone aggregate at the mixing yard and carriage of
the precoated materials for dumping at a suitable place as directed
including cost and carriage of bitumen, emulsion and including hire
charges of machinares and incidental charges complete as per
direction of E.I.C.
Sq.m. 25.80
P-25 / 6 Laying biyuminous primer for primin of base coarse with cationic
bitumen emulsion of appropriate grade and requisite quantity
including preparation of the surface to be primed through cleaning
and sweeping, uprooting weeds, grass etc. dampening the surface
before hand ( in case of emulsion only) spraying the primer using
sprayer mounted on distributor truck or with hand sprayer using
mechanical pump including cost and carriage of bitumen emulsion
and all other incidental costs of work. Quantity of Bitumenous
primer reqd:-
Sq.m. 4.10
all other coats including hire charges of all sorts of machineries and
and equipments for construction and quality control as per MOSTs
specification (Third Revision) & cost of fuel and lubricants in this
connection. Constn operation should be followed as per
Specification. Sq.m. 27.00
P-27 / 10 Bituminous Macadam for profile corrective course type B (not less than
40 mm thick) by HOT MIX PLANT using approved aggregates conforming
to specified grading and precoating the same with bitumen @ 3.00% by wt.
of total mix including through cleaning of the surface applying tack coat
with bitumen emulsion @ 3 kg/10sqm. or 4 kg/10sqm. as the case may be
(except where proceeded by a bituminous levelling course) screening
cleaning stone materials and preparing a uniform and quality mix carying
the hot premixed material by means of tipper truck or any other approved
and suitable arrangements upto a distance of 20 km. spreading the mixed
materials at specified laying temperature over the surface (kept ready by
thorough cleaning and sweering) by means of a suitable paver finisher,
tamping and finishing the mix to specified grade, line and cross section,
through rolling with suiable power rollers for break down, inter mediste and
finished rolling to achieve the desired dencity as per relevant code, hand
packing and pinning to give an even surface
including cost and carriage of bitumen and bitumen emulsion and coarse &
fine aggregates and also hire charges of HOT MIX PLANT and all other
machines and eqipments for construction and quality control as per IRC
specification, cost of fule and lubricants and wages of operational staff all
complete.
P-28 / 11 Bituminous Macadam (as base/ binder course) by HOT MIX PLANT using
approved aggregates conforming to specified grading and precoating the
same with bitumen @ 3.25% by wt. of total mix including through cleaning
of the surface applying tack coat with bitumen emulsion @ 3 kg/10sqm. or
4 kg/10sqm. as the case may be (except where proceeded by a bituminous
levelling course) screening cleaning stone materials and preparing a
uniform and quality mix carying the hot premixed material by means of
tipper truck or any other approved and suitable arrangements upto a
distance of 20 km. spreading the mixed materials at specified laying
temperature over the surface (kept ready by thorough cleaning and
sweering) by means of a suitable paver finisher, tamping and finishing the
mix to specified grade, line and cross section, through rolling with suiable
power rollers for break down, inter mediste and finished rolling to achieve
the desired dencity as per relevant code, hand packing and pinning to give
an even surface
B) Extra for tack coat over above corresponding rates :- Refer item
no :- 37
B) Extra for tack coat over above corresponding rates :- Refer item
no :- 37
P-30 / 13 Laying 20 mm thick premix carpet (open graded) by HOT MIX PLANT
using 1.8 cu.m. of 13.2 mm size and 0.9 cu.m. of 11.2 mm size aggregate
per 100 sq.m. of surface including through cleaning of the surface, applying
tack coat, screening cleaning and preheating stone chipes and fully
precoating the same with hot matrix @ 54 kg/cu.m. of aggregate carrying
the mixture by tipper trucks or any other suitable arrangements within a
distance of 20 kms and laying the mixture uniformly over the surface with
paver finisher including manual operations as and when required for proper
level, grade and camber thoroughly rolling by power roller including the
cost and carriage of stone chips and matrix, heating the matrix, preheating
the aggregates to required temperature and including the hire charges of
H.M.P. and other machineries, pay of operators, cost of fule and lubricants
etc. and all other cost.
B) Extra for tack coat over above corresponding rates :- Refer item
no :- 37
B) Extra for tack coat over above corresponding rates :- Refer item
no :- 37
& quality control as per IRC specification including cost of fuels and
lubricants and eages of operational staff (to be recovered as per
hire charges for Central Mechineries & Wages etc.) al complete
Sq.m. 8.20
P-36 / 20 Mix Seal surfaceing by MOBILE HOT MIX PLANT (LIGHT DUTY)
(20 mm nominal thickness) using 0.27 cu.m. of mineral aggregate
(coarse and fine aggregate) per 10 sq.m. of surface as per
specification and approved job mix formula, cleaning the surface
throughly, applying tack coat @ 3 kg/ 10 sq.m.and screening and
cleaning the agregates as necessary, preheating aggregates,
precoating the same in MOBILE HOT MIX PLANT (LIGHT DUTY)
with hot matrix, carrying the mixture by any suitable arrangements
and lying the premixed materials uniformly including manual
operation as and when required, compacting with power roller
including the cost and carriage of aggregates and matrix, inclusive
of tack coat, heating the matrix and aggregates, including the hire
charges of MOBILE HOT MIX PLANT (LIGHT DUTY) and other
machineries and equipments for construction dn quality control as
per IRC Specifications including cost of fuels and lubricants and
eages of operational staff (to be recovered as per hire charges for
Central Mechineries & Wages etc.) and all other cost complete.
B) Extra for tack coat over above corresponding rates :- Refer item
no :- 37 Sq.m.
B) Extra for tack coat over above corresponding rates :- Refer item
no :- 37
P-40 / 25 Laying 20mm thick premixed carpet (open grade) using 1.8m3 of
13.2 mm size and 0.9m3 of 11.2mm size stone aggregate per 100
m2 of surface including thorough cleaning of the surface, applying
tack coat, screening, cleaning and preheating stone chips and fully
precoating the same with hot matrix @ 54kg per m3 of aggregates
laying the premixed chips uniformly over the surface, hand packing,
thoroughly rolling by power roller including the cost and carriage of
stone chips and matrix, heating the matrix and all other cost and
charges in this connection including hire charges and cost of fuel
and lubricants of machineries and equipments for construction and
quality control as per IRC specification complete.
Sq.m. 3.60
P-43 / 30 Lying premixed seal coat (Type-B) using 0.6m3 of grit or sand
(passing 2.36mm sieve and retaind on 180 micron) per 100sq
metre area including cleaning the surface, preheating the grit /
sand by MOBILE HOT MIX PLANT (LIGHT DUTY) of capacity 3-5
Tonnes/Hour. Suitable pans, mMixing the preheated grit / sand with
hotmatrix @ 113.50kg per m3 of grit/sand, laying the mixture
uniformly over the surface and rolling with power roller including the
cost and carriage of grit/sand and matrix, heating matrix and
grit/sand and all other costs and charges in this connection
including hire charges and cost of fuel and lubricants of
machineries and equipments for construction and quality control
complete.
On Suitable Pan
a) On freshly laid premixed surface, without tack coat Sq.m. 3.80
P-45 / 35 If bulk bitumen is issued from the deptt. Vat for any of above item of
works. Bitumen into empty drums by cutting or other means from
the deptt. Underground vat including hire charges of bitumen drum
and labour for cutting and carriage etc. complete.
M.T. 200.00
P-47 / 37 Lying tack coat using Cationic Bitumen emulsion (R.S. or M.S.
grade) conforming to IS. 8887-1978 over Water Bound Macadam
or Black top Surface including, hire charges of machineries and
labour charges and cost of fuel and lubricant for cleaning and
moistening the surface, spreading emulsion etc. all complete as per
specification and direction of the Engineer-in-charge.
P-48 / 39 Laying liquid seal coat (Type A) with stone chips on black top
surface using cationic bitumen emulsion (R.S. or M.S. grade)
conforming to IS : 8887 - 1978 including through cleaning the
surface applying emulsion @ 130 kg per 100 sq.m. and blinding
the same with cleaned and washed stone chips, (6.7 mm size
100% passing through IS: 9.5 mm sieve and retained on IS: 2.36
mm sieve) by suitable means @ 0.6 cu.m. per 100 sq.m. and
rolling with power roller as per specification and direction of E.I.C.
to all complete including cost of labour hire and running charges
including cost of fuel and lubricants of road roller and other tools
and plants and cost of all other incidental charges including cost
and carriage of stone chips and emulsion complete.
Sq.m. 3.80
P-49 / 40 Laying liquid seal coat (Type B) on freshly laid premix carpet
without tack coat using 0.6m3 of stone grit (passing 2.36mm sieve
and retaind on 1.8 mm sieve) or coarse sand (F.M. more than 2.5)
per 100 sq m. premixing with Cationic Bitumen Emulsion (M.S.
grade) conforming to IS : 8887 - 1978 @ 180 kg per cu.m. of stone
grit/ sand including cleaning surface, screening washing and
wetting the stone grit/ sand, mixing suitably and laying the mixture
uniformly over the premix carpet and rolling with power roller till the
premixed material completely seals the void in the premix carpet
etc. all complete as per specification and direction of the E.I.C.
including the cost of all labour, hire and running charges including
cost of fuel and lubricants of road roller and other tools and plants
and cost of all other incidental charges including cost and carriage
of stone grit/ coarse sand and emulsion complete.
P-49 / 41 Laying stabilisation coat (with painting of matrix and spreading dry
medium sand over it) including through cleaning of the surface
including uprooting weeds, grass or small plants, laying of requisite
quantity of matrix (hot) spreading dry medium sand uniformly in
stages with total of 0.9 cu.m. per 100 sq.m. including cost and
carriage of sand matrix, heating matrix and all other costs
incidental to the work complete.
(B) Extra over above corresponding rate on the black top surface
when tack coat is to be done @ 3 kg/ 10 sq.m. The rate of tack
coat as per item no - 37b is to be added to arrive at the complete
rate