Professional Documents
Culture Documents
CFX-750™ Display
Version 1.05
Revision A
June 2011
Part Number 94100-00-ENG
94100-00-ENG
Contact Information – proof of purchase
Trimble Navigation Limited – a copy of this Trimble warranty
Trimble Agriculture Division – a description of the nonconforming Product including the model
10355 Westmoor Drive number
Suite #100 – an explanation of the problem
Westminster, CO 80021 The customer service representative may need additional information
USA from you depending on the nature of the problem.
Legal Notices Warranty Exclusions and Disclaimer
Copyright and Trademarks This Product limited warranty shall only apply in the event and to the
extent that (a) the Product is properly and correctly installed,
© 2009-2011, Trimble Navigation Limited. All rights reserved. configured, interfaced, maintained, stored, and operated in accordance
Trimble, the Globe and Triangle logo, AgGPS, CFX-750, EZ-Boom, with Trimble's applicable operator's manual and specifications, and; (b)
EZ-Guide, EZ-Steer, GreenSeeker, and Tru Count Air Clutch are the Product is not modified or misused. This Product limited warranty
trademarks of Trimble Navigation Limited, registered in the United shall not apply to, and Trimble shall not be responsible for, defects or
States and in other countries. Autopilot, Field-IQ, FieldManager, performance problems resulting from (i) the combination or utilization
Rawson, TrueGuide, TrueTracker, and Tru Application Control are of the Product with hardware or software products, information, data,
trademarks of Trimble Navigation Limited. systems, interfaces, or devices not made, supplied, or specified by
All other trademarks are the property of their respective owners. Trimble; (ii) the operation of the Product under any specification other
than, or in addition to, Trimble's standard specifications for its products;
Release Notice (iii) the unauthorized installation, modification, or use of the Product;
(iv) damage caused by: accident, lightning or other electrical discharge,
This is the June 2011 release (Revision A) of the CFX-750 Display Cabling fresh or salt water immersion or spray (outside of Product
Guide. It applies to version 1.05 of the CFX-750 display firmware. specifications); or exposure to environmental conditions for which the
LIMITED WARRANTY TERMS AND CONDITIONS Product is not intended; (v) normal wear and tear on consumable parts
(e.g., batteries); or (vi) cosmetic damage. Trimble does not warrant or
Product Limited Warranty guarantee the results obtained through the use of the Product, or that
Trimble Navigation Limited (“Trimble”) warrants that this product and software components will operate error free.
its internal components (the “Product”) shall be free from defects in NOTICE REGARDING PRODUCTS EQUIPPED WITH TECHNOLOGY
materials and workmanship and will substantially conform to Trimble’s CAPABLE OF TRACKING SATELLITE SIGNALS FROM SATELLITE BASED
applicable published specifications for the Product for a period of two AUGMENTATION SYSTEMS (SBAS) (WAAS/EGNOS, AND MSAS),
(2) years, starting from the earlier of (i) the date of installation, or (ii) six OMNISTAR, GPS, MODERNIZED GPS OR GLONASS SATELLITES, OR
(6) months from the date of original Product shipment from Trimble. FROM IALA BEACON SOURCES: TRIMBLE IS NOT RESPONSIBLE FOR
THE OPERATION OR FAILURE OF OPERATION OF ANY SATELLITE
Product Software BASED POSITIONING SYSTEM OR THE AVAILABILITY OF ANY
Product software, whether built into hardware circuitry as firmware, SATELLITE BASED POSITIONING SIGNALS.
provided as a standalone computer software product, embedded in flash THE FOREGOING LIMITED WARRANTY TERMS STATE TRIMBLE’S ENTIRE
memory, or stored on magnetic or other media, is licensed solely for use LIABILITY, AND YOUR EXCLUSIVE REMEDIES, RELATING TO THE TRIMBLE
with or as an integral part of the Product and is not sold. If accompanied PRODUCT. EXCEPT AS OTHERWISE EXPRESSLY PROVIDED HEREIN, THE
by a separate end user license agreement (“EULA”), use of any such PRODUCT, AND ACCOMPANYING DOCUMENTATION AND MATERIALS
software will be subject to the terms of such end user license agreement ARE PROVIDED “AS-IS” AND WITHOUT EXPRESS OR IMPLIED WARRANTY
(including any differing limited warranty terms, exclusions, and OF ANY KIND, BY EITHER TRIMBLE OR ANYONE WHO HAS BEEN
limitations), which shall control over the terms and conditions set forth INVOLVED IN ITS CREATION, PRODUCTION, INSTALLATION, OR
in this limited warranty. DISTRIBUTION, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
Software Fixes WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, TITLE, AND NONINFRINGEMENT. THE STATED EXPRESS
During the limited warranty period you will be entitled to receive such WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE
Fixes to the Product software that Trimble releases and makes PART OF TRIMBLE ARISING OUT OF, OR IN CONNECTION WITH , ANY
commercially available and for which it does not charge separately, PRODUCT. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW
subject to the procedures for delivery to purchasers of Trimble products LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED
generally. If you have purchased the Product from an authorized Trimble WARRANTY, THE ABOVE LIMITATION MAY NOT APPLY OR FULLY APPLY
dealer rather than from Trimble directly, Trimble may, at its option, TO YOU .
forward the software Fix to the Trimble dealer for final distribution to
you. Minor Updates, Major Upgrades, new products, or substantially Limitation of Liability
new software releases, as identified by Trimble, are expressly excluded TRIMBLE'S ENTIRE LIABILITY UNDER ANY PROVISION HEREIN SHALL BE
from this update process and limited warranty. Receipt of software Fixes LIMITED TO THE AMOUNT PAID BY YOU FOR THE PRODUCT. TO THE
or other enhancements shall not serve to extend the limited warranty MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT
period. SHALL TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT,
For purposes of this warranty the following definitions shall apply: (1) SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGE WHATSOEVER
“Fix(es)” means an error correction or other update created to fix a UNDER ANY CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANYWAY
previous software version that does not substantially conform to its TO THE PRODUCTS, SOFTWARE AND ACCOMPANYING DOCUMENTATION
Trimble specifications; (2) “Minor Update” occurs when enhancements AND MATERIALS, (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
are made to current features in a software program; and (3) “Major LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA , OR
Upgrade” occurs when significant new features are added to software, or ANY OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER TRIMBLE HAS
when a new product containing new features replaces the further BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLESS
development of a current product line. Trimble reserves the right to OF THE COURSE OF DEALING WHICH DEVELOPS OR HAS DEVELOPED
determine, in its sole discretion, what constitutes a Fix, Minor Update, BETWEEN YOU AND TRIMBLE. BECAUSE SOME STATES AND
or Major Upgrade. JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
Warranty Remedies LIMITATION MAY NOT APPLY TO YOU.
If the Trimble Product fails during the warranty period for reasons PLEASE NOTE: THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS
covered by this limited warranty and you notify Trimble of such failure WILL NOT APPLY TO PRODUCTS PURCHASED IN THOSE
during the warranty period, Trimble will repair OR replace the JURISDICTIONS (E.G., MEMBER STATES OF THE EUROPEAN ECONOMIC
nonconforming Product with new, equivalent to new, or reconditioned AREA) IN WHICH PRODUCT WARRANTIES ARE THE RESPONSIBILITY
parts or Product, OR refund the Product purchase price paid by you, at OF THE LOCAL TRIMBLE AUTHORIZED DEALER FROM WHOM THE
Trimble’s option, upon your return of the Product in accordance with PRODUCTS ARE ACQUIRED. IN SUCH A CASE, PLEASE CONTACT YOUR
Trimble's product return procedures then in effect. LOCAL TRIMBLE AUTHORIZED DEALER FOR APPLICABLE WARRANTY
INFORMATION.
How to Obtain Warranty Service
To obtain warranty service for the Product, please contact your local Official Language
Trimble authorized dealer. Alternatively, you may contact Trimble to THE OFFICIAL LANGUAGE OF THESE TERMS AND CONDITIONS IS
request warranty service at +1-408-481-6940 (24 hours a day) or e-mail ENGLISH . IN THE EVENT OF A CONFLICT BETWEEN ENGLISH AND OTHER
your request to trimble_support@trimble.com. Please be prepared to LANGUAGE VERSIONS, THE ENGLISH LANGUAGE SHALL CONTROL.
provide:
– your name, address, and telephone numbers
8 Installing Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
CFX-750 / 2 AgCam cameras / Autopilot / RTK corrections . . . . . . . . . . . . . . . . . . . . . . 72
CFX-750 / Autopilot / Remote-mounted LB25 external lightbar . . . . . . . . . . . . . . . . . . . 74
CFX-750 / Autopilot / EZ-Remote joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
1
Cable Configuration 1
Configuration options
The CFX-750 display can operate as a standalone guidance system, or you can connect it to a
range of devices to expand its functionality. This document shows you how to complete those
cable connections.
• The replicator port on most cables breaks away the pins not used by the primary device
the cable was designed for.
For example, if the RS232 port is required, the port replicator breaks out the CAN, digital,
pins etc. Do not connect the port replicator to the NavController II.
• When using the LB25 lightbar, you must use cable P/N 72420.
c d
e
Function Communication type Dedicated CAN Port A Port B Port C
port required?
c d e
Autopilot RS232 F
EZ-Steer CAN F F F F
Field-IQ CAN F F F
Serial VR RS232 F F
2
Connecting the Display Only 2
In this chapter:
g
c
c
g
i
h
f
e
Item Description Trimble part number
c CFX-750 display 94100-xx
Note – RTK password required.
d CFX-750 power cable 77282
3
Connecting to an EZ-Steer System 3
g c
d
j
h
k
e i
Item Description Trimble part number
i CFX-750 power cable with relay and switch (power bus) 67259
Note – The EZ-Steer assisted steering system must be powered separately to power the motor.
c
g
d j
h k
Note – The EZ-Steer assisted steering system must be powered separately to power the motor.
4
Connecting to an Autopilot System 4
c
k
P3 / GPS
connector
j i
g
l
d
h
f
e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness l will result in damage to the CFX-750
display and will void the warranty.
CFX-750 power cable with relay and switch (power bus) 67259
e
Note – To enable the CFX-750 display to power-up the NavController
II, plug the 2-pin Delphi together.
Basic power cable 67258
f
CFX-750 to NavController II cable with port replicator 75741
g
2 pin DTM to 2 pin DT power adaptor 67095
h
i NavController II 55563-00
c m
j l
i P3 / GPS
connector g
d
n
h
f
e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness n will result in damage to the CFX-750
display and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
NavController II 55563-00
i
8 m GPS TNC/TNC RT angle cable 50449
j
AG25 GNSS antenna 77038-00
k
m
c
k
l
j
d
g
i p
P3 / GPS
connector
h
e
f n
o
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness p will result in damage to the CFX-750
display and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
i NavController II 55563-00
c
g i
h k
f
d m
j l
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable j to
the P4 connector of the NavController II harness will result in damage to the CFX-750 display and
will void the warranty.
l NavController II 55563-00
e
P3 / GPS j
g connector k
d
f
h
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable e to
the P4 or P12 connector of the NavController II harness f will result in damage to the CFX-750
display and will void the warranty.
g NavController II 55563-00
i Autopilot to AGCO power and CAN interface cable 77644 (incl w/ kit 77648)
j Adaptor for early Autoguide models (optional) 77647 (incl w/ kit 77648)
k Power adaptor for early Autoguide models (optional) 77646 (incl w/ kit 77648)
5
Connecting the Field-IQ Crop Input
Control System 5
l c
To vehicle battery
f
k
m e
d o
Note:
h not connected
g
i n
j To implement
CFX-750 power cable with relay and switch (power bus) 67259
e
f Basic power cable 67258
77368
g Cab to hitch CAN cable
Remote foot switch (optional) 78150
h
i Field-IQ master switch box 75050-01
l c
k f p
m d e
h
o
i
g
j
n
To implement
CFX-750 power cable with relay and switch (power bus) 67259
e
f Basic power cable 67258
77368
g Cab to hitch CAN cable
Remote foot switch (optional) 78150
h
i Field-IQ master switch box 75050-01
c f
k d e
g
i Note:
not connected
j h
p m
q
o l
n
Item Description Trimble part number
c CFX-750 display 94100-xx
CFX-750 power cable with relay and switch (power bus) 67259
e
f Basic power cable 67258
s
c j
q r g
f
p e
o h
d k
i
m Note:
not connected
n l
x u
y t
w
v
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable e
to the P4 or P12 connector of the NavController II harness f will result in damage to the
CFX-750 display and will void the warranty.
NavController II 55563-00
g
77368
l Cab to hitch CAN cable
f
h c
i
d e
k n
j
l m
Note: to Raven or
EZ-Boom harness
75060-01
l 12 section switch box
c f
h
g
e
d
i
n
k
j
m
l
o
75060-01
l 12 section switch box
f
h c
i e
d
n
k
j
m
l
75060-01
l 12 section switch box
g c
i e
d
k n
j
l m
75060-01
l 12 section switch box
h c f
g
e
i d
l m
k o
j
n
p
NavController II 55563-00
g
2 pin DTM to 2 pin DT power adaptor 67095
h
i FmX power cable with relay and switch (power bus) 67259
75774-00
l Rate and section control module
l m p
k o
j
q
Item Description Trimble part number
c CFX-750 display 94100-xx
NavController II 55563-00
g
2 pin DTM to 2 pin DT power adaptor 67095
h
i FmX power cable with relay and switch (power bus) 67259
75774-00
l Rate and section control module
e the cab
f g h
d k
i
j u
Inside
the cab
m l
Main cab harness replicated on sprayer and spreader
p
o n
q r s t
c
h
f g
e m i
d
j
Field-IQ Cab Kit - 80810-00
n
k
Necessary components to
replicate spreader
6
Connecting to Radar Output and
Serial Control 6
j
c
p
k
m
d
i g
o n l P3 / GPS
connector
h
f e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
CFX-750 display, and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
j
p c
m
g
o d i
n
l P3 / GPS
connector
h
e
f
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
CFX-750 display, and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
k
c
o p
j
d g
m i
n l P3 / GPS
connector
To rate controller
h
e
f
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
CFX-750 display and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
k
c
l
m
h
n j
d
i P3 / GPS
connector
f e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
CFX-750 display and will void the warranty.
Note – For the Hardi 5500 controller to work with the CFX-750 display, it must have firmware version
3.16 or greater installed and have a JOBCOM control box connected.
e CFX-750 power cable with relay and switch (power bus) 67259
7
Connecting Modems 7
c
k n
o j
P3 / GPS
connector i
m d g
n l
h
f e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
CFX-750 display and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
Basic power cable 67258
f
CFX-750 to NavController II cable with port replicator 75741
g
2 pin DTM to 2 pin DT power adaptor 67095
h
NavController II 55563-00
i
8m GPS TNC/TNC RT angle cable 76442
j
AG25 GNSS antenna 77038-00
k
l Main NavController II cable 54601
k nc
j
P3 / GPS
connector
i
d
g l
f
m e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
CFX-750 display and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
k c
n
o j
P3 / GPS
connector i
p
d g
m
l
q
h
f e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness l will result in damage to the CFX-750
display and will void the warranty.
e CFX-750 power cable with relay and switch (power bus) 67259
q DCM-300 power harness: Use either the powerbus or direct power 82026
leads harness.
8
Installing Accessories 8
c m
k
n
l
j n o
o
n
d i g
p P3 / GPS
connector
h
f e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness p will result in damage to the CFX-750
display, and will void the warranty.
CFX-750 power cable with relay and switch (power bus) 67259
e
Basic power cable 67258
f
CFX-750 to NavController II cable with port replicator 75741
g
2 pin DTM to 2 pin DT power adaptor 67095
h
i NavController II 55563-00
c m
k
l
j
s r q n g
d P3 / GPS
i connector
t o
p
f e
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness p will result in damage to the CFX-750
display and will void the warranty.
Note – If you use the LB25 external lightbar, do not use another CAN device on the same port.
67259
e CFX-750 power cable with relay and switch (power bus)
c m
k
l
j
s q p n
P3 / GPS
g
d connector
r i o
h
e
f
C CAUTION – Connecting the Port Replicator on the CFX-750 display to NavController II cable g to
the P4 or P12 connector of the NavController II harness o will result in damage to the CFX-750
display and will void the warranty.
67259
e CFX-750 power cable with relay and switch (power bus)