You are on page 1of 3

Operating Instructions Operating Instructions

RB Tube Cutter Code No. RB Tube Cutter Code No.


Model N30P 427830 Model N30S 427630

For Coated and Nude Copper Pipes For Thin wall Stainless Steel Pipes
For safe, efficient use, read these instructions carefully before use. For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time. instructions in a safe place so that you can refer to them at any time.

・Use the cutter only for the types of tubes described in these ・Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter. intended use, may result in an accident or damage to the cutter.
・Always inspect the cutter before use. If you find anything wrong, ・Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made. do not use until repairs have been made.
・When cutting pipes, make sure the blade doesn't touch your hand. ・When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe. Never place your fingers between the blade and the pipe.
・Avoid dropping the cutter either when using or carrying it. ・Avoid dropping the cutter either when using or carrying it.
・Be sure to remove any water or flux from the cutter. Failure to do ・Be sure to remove any water or flux from the cutter. Failure to do
so could result in the bearings becoming rusty and malfunctioning. so could result in the bearings becoming rusty and malfunctioning.

Instructions Instructions
Place the pipe on the cutter between Rollers Blade Place the pipe on the cutter between Rollers Blade
the rollers and the blade as shown in ① Turn the rollers and the blade as shown in ① Turn
Fig. 1. When doing so, make sure the Fig. 1. When doing so, make sure the
end of the pipe protrudes further than end of the pipe protrudes further than
the width of the rollers. Once the blade the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise Pipe engages the pipe, turn the grip clockwise Pipe
again 1/4 of a turn. again 1/4 of a turn. Grip Fig.1
Grip Fig.1

Rotate the cutter back and forth 2 or 3 Rotate the cutter back and forth 2 or 3
times through 90゜(see Fig.4 on reverse times through 90゜(see Fig.4 on reverse
side) then fully one time to make a cutting side) then fully one time to make a cutting
guideline. Rotate guideline. Rotate

Fig.2 Fig.2

Then turn the grip slowly, (1/8 of a turn for Turn grip approx.1/8 of 3 or 4 turn Then turn the grip slowly, (1/8 of a turn for Turn grip approx.1/8 of 3 or 4 turn
every 3 or 4 rotations of the cutter) and every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually keep rotating the cutter as you gradually
cut deeper into the pipe. cut deeper into the pipe.
・ Avoid cutting too quickly or the pipe may ・ Avoid cutting too quickly or the pipe may
become distorted and the life of the blades become distorted and the life of the blades
reduced. reduced.
・ By attaching a special blade (sold separately) ・ By attaching a special blade (sold separately)
you can also cut copper (annealed or Rotate cutter once Fig.3 you can also cut copper (annealed or Rotate cutter once Fig.3
unannealed) and brass pipes. unannealed) and brass pipes.

Specifications Specifications
Application Coated and Nude Copper Pipes Application Thin wall Stainless Steel Pipes
Cutting capacity External Diam. 5 - 34 mm Cutting capacity External Diam. 5 - 34 mm
Weight (main unit) 350g Weight (main unit) 350g
Blade diameter φ32 Blade diameter φ30
Rollers 625ZZ Rollers 625ZZ
Spare Blade Code No. 424237 Spare Blade Code No. 424233, 424284
Optional Extras Blade for Thin wall Stainless Steel Pipes Optional Extras Blade for Coated and Nude Copper pipes
(Code No.424233, 424284) (Code No. 424237)

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan 1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan
Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878 Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878
www.rexind.co.jp www.rexind.co.jp

4V440-E2 4V410-E1
1304D01000 0808D01000
Operating Instructions Operating Instructions

RB Tube Cutter Code No. RB Tube Cutter Code No.


Model N42P 427842 Model N42S 427642

For Coated and Nude Copper Pipes For Thin wall Stainless Steel Pipes
For safe, efficient use, read these instructions carefully before use. For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time. instructions in a safe place so that you can refer to them at any time.

・Use the cutter only for the types of tubes described in these ・Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter. intended use, may result in an accident or damage to the cutter.
・Always inspect the cutter before use. If you find anything wrong, ・Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made. do not use until repairs have been made.
・When cutting pipes, make sure the blade doesn't touch your hand. ・When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe. Never place your fingers between the blade and the pipe.
・Avoid dropping the cutter either when using or carrying it. ・Avoid dropping the cutter either when using or carrying it.
・Be sure to remove any water or flux from the cutter. Failure to do ・Be sure to remove any water or flux from the cutter. Failure to do
so could result in the bearings becoming rusty and malfunctioning. so could result in the bearings becoming rusty and malfunctioning.

Instructions Instructions
Place the pipe on the cutter between Rollers Blade Place the pipe on the cutter between Rollers Blade
the rollers and the blade as shown in the rollers and the blade as shown in
Fig. 1. When doing so, make sure the ① Turn Fig. 1. When doing so, make sure the ① Turn
end of the pipe protrudes further than end of the pipe protrudes further than
the width of the rollers. Once the blade the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise Pipe engages the pipe, turn the grip clockwise Pipe
again 1/4 of a turn. again 1/4 of a turn.
Grip Fig.1 Grip Fig.1

Rotate the cutter back and forth 2 or 3 Rotate the cutter back and forth 2 or 3
times through 90゜(see Fig.4 on reverse times through 90゜(see Fig.4 on reverse
side) then fully one time to make a cutting side) then fully one time to make a cutting
guideline. Rotate guideline. Rotate

Fig.2 Fig.2

Then turn the grip slowly, (1/8 of a turn for Turn grip approx.1/8 of 3 or 4 turn Then turn the grip slowly, (1/8 of a turn for Turn grip approx.1/8 of 3 or 4 turn
every 3 or 4 rotations of the cutter) and every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually keep rotating the cutter as you gradually
cut deeper into the pipe. cut deeper into the pipe.
・ Avoid cutting too quickly or the pipe may ・ Avoid cutting too quickly or the pipe may
become distorted and the life of the blades become distorted and the life of the blades
reduced. reduced.
・ By attaching a special blade (sold separately) ・ By attaching a special blade (sold separately)
you can also cut copper (annealed or Rotate cutter once Fig.3 you can also cut copper (annealed or Rotate cutter once Fig.3
unannealed) and brass pipes. unannealed) and brass pipes.

Specifications Specifications
Application Coated and Nude Copper Pipes Application Thin wall Stainless Steel Pipes
Cutting capacity External Diam. 6 - 42 mm Cutting capacity External Diam. 6 - 42 mm
Weight (main unit) 400g Weight (main unit) 400g
Blade diameter φ32 Blade diameter φ30
Rollers 625ZZ Rollers 625ZZ
Spare Blade Code No. 424237 Spare Blade Code No. 424233, 424284
Optional Extras Blade for Thin wall Stainless Steel Pipes Optional Extras Blade for Coated and Nude Copper pipes
(Code No.424233, 424284) (Code No. 424237)

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan 1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan
Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878 Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878
www.rexind.co.jp www.rexind.co.jp

4V450-E3 4V420-E1
1304D01000 0901D01000
Operating Instructions Operating Instructions

RB Tube Cutter Code No.


RB Tube Cutter Code No.

Model N67P 427867 Model N67S 427667

For Coated and Nude Copper Pipes For Thin wall Stainless Steel Pipes
For safe, efficient use, read these instructions carefully before use. For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these instructions Use the device correctly and for its intended use only. Keep these instructions
in a safe place so that you can refer to them at any time. in a safe place so that you can refer to them at any time.

Use・the cutter only for the types of tubes described in these instructions. Use・the cutter only for the types of tubes described in these instructions.
Use with other pipes, or for purposes other than the intended use, may Use with other pipes, or for purposes other than the intended use, may
result in an accident or damage to the cutter. result in an accident or damage to the cutter.
Always
・ inspect the cutter before use. If you find anything wrong, do not use Always
・ inspect the cutter before use. If you find anything wrong, do not use
until repairs have been made. until repairs have been made.
When
・ cutting pipes, make sure the blade doesn't touch your hand. When
・ cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe. Never place your fingers between the blade and the pipe.
Avoid
・ dropping the cutter either when using or carrying it. Avoid
・ dropping the cutter either when using or carrying it.
Be ・
sure to remove any water or flux from the cutter. Failure to do so could Be ・
sure to remove any water or flux from the cutter. Failure to do so could
result in the bearings becoming rusty and malfunctioning. result in the bearings becoming rusty and malfunctioning.

Instructions Instructions
Place the pipe on the cutter as shown in Fig.1, Rollers Blade Place the pipe on the cutter as shown in Fig.1, Rollers Blade
making sure the end of the pipe protrudes further ① Push in making sure the end of the pipe protrudes further ① Push in
than the width of the rollers. Push in the grip until than the width of the rollers. Push in the grip until
the rollers and blade lightly contact the pipe. the rollers and blade lightly contact the pipe.

② ②
Turn Pipe Turn
Pipe
Grip Fig.1 Grip Fig.1

At that point, turn the grip clockwise again 1/4 At that point, turn the grip clockwise again 1/4
of a turn.Rotate the cutter back and forth 2 or of a turn.Rotate the cutter back and forth 2 or
3 times through 90゜ (see Fig. 5 on reverse side) 3 times through 90゜ (see Fig. 5 on reverse side)
then once more through one complete rotation Rotate then once more through one complete rotation Rotate
to make a cutting guideline. to make a cutting guideline.

Fig.2 Fig.2

Then turn the grip slowly, (1/8 of a turn for every Turn grip approx.1/8 of a 3 or 4 turn Then turn the grip slowly, (1/8 of a turn for every Turn grip approx.1/8 of a 3 or 4 turn
3 or 4 rotations of the cutter) and keep rotating the 3 or 4 rotations of the cutter) and keep rotating the
cutter as you gradually cut deeper into the pipe. cutter as you gradually cut deeper into the pipe.

・Avoid cutting too quickly or the pipe may become ・Avoid cutting too quickly or the pipe may become
distorted and the life of the blades reduced. distorted and the life of the blades reduced.

Rotate cutter fully once Fig.3 Rotate cutter fully once Fig.3

Press the lever on the underside of the cutter Press the lever on the underside of the cutter
(see Fig. 4) to release the blade. Press
(see Fig. 4) to release the blade. Press
Springs out Springs out
When you release the blade, the grip springs When you release the blade, the grip springs
back quite forcefully. back quite forcefully.
To avoid injury, hold the cutter away from your To avoid injury, hold the cutter away from your
face or other parts of your body. Fig.4 face or other parts of your body. Fig.4

・By attaching a special blade (sold separately) ・By attaching a special blade (sold separately)
you can also cut copper (annealed or unannealed) you can also cut copper (annealed or unannealed)
and brass pipes and brass pipes

Specifications Specifications
Application Coated and Nude Copper Pipes Application Thin Wall Stainless Steel Pipes
Cutting capacity External Diam. 12 ~ 67 mm Cutting capacity External Diam. 12 - 67 mm
Weight (main unit) 870g Weight (main unit) 870g
Blade diameter φ32 Blade diameter φ30
Rollers 625ZZ Rollers 625ZZ
Spare Blade Code No. 424237 Spare Blade Code No. 424233, 424284
Optional Extras Blade for Thin Wall Stainless Steel Pipes Optional Extras Blade for Coated and Nude Copper Pipes
(Code No.424233, 424284) (Code No. 424237)

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan 1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan
Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878 Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878
www.rexind.co.jp www.rexind.co.jp

4V460-E1 4V430-E2
0808D01000 1107D01000

You might also like