Professional Documents
Culture Documents
CUT LINE
Tampa
Tampa Class V Orgs Vol. 3.0 FF&E SPECIFICATION Class V Orgs
Vol. 3.0
FF&E SPECIFICATIONS
13.7042.430
TYP. CUT LINE
Tampa
Tampa Class V Orgs Vol.3.1 FF&E SPECIFICATION Class V Orgs
Vol. 3.1
FF&E SPECIFICATIONS
13.7042.430
VOL. 3 TABLE OF CONTENTS
GENERAL
Preamble
FF&E Quantity Matrix
FF&E Specifications Legend
INDEX
OFCI SPECIFICATIONS
C Carpet
CPT Carpet Tile
FPW Fabric Panel Wrap
HDW Hardware
CUSTOM FURNITURE
Line Drawings
Appendix
SAMPLE REFERENCE
Preamble
CSI-Org Projects
13.7042.430
TABLE OF CONTENTS
____________________________________________________________________
0.0 Introduction Page
0.1 General Notes and Conditions 0.10
0.2 Life Safety & Fire Protection 0.20
A. Scope
The following specifications have been prepared in accordance with Owner
approved design schemes and budgets by Gensler for the following areas of the
project: __________________________.
B. Item Mark
The item mark is a code number used to locate each item on a furniture, finish or
reflected ceiling plan. The mark consists of two parts. The first part indicates the
area location, the second indicates the item number. Refer to "Item Mark
Legend" (1.1C) for appropriate codes.
Example: AUD-300
AUD-Auditing Room, 300 – Casegood identification number
Carpet (OFCI) C
Carpet Tile (OFCI) CPT
Fabric Panel Wrap (OFCI) FPW
Plumbing/Toilet Accessories
Carpet / Area Rugs
Hardware
Casegoods & Tables
Seating & Upholstery
Bedding & Drapery
Lighting
Art /Mirrors
Accessories/Shower Curtain
Special Equipment
0.10-1
Gensler = 13.7042.000
D. Item Specification
E. Item Substitution
Any substitution of a specified item must be approved by the designer and the
following procedures followed:
2. Any substitution must meet all applicable federal, state, local or other codes and
regulations. Mock ups or sample for flame testing shall be provided by the
manufacturer at their expense. Testing and documentation proving compliance
shall be the responsibility of the purchasing agent or vendor.
3. Full size samples will be required for all items proposed for substitution.
4. The cost of shipment and return of the proposed substitution item shall be the
responsibility of the purchasing agent or vendor.
5. All samples shall be submitted for the designer's approval before installation or
fabrication.
F. Custom Submittals
1. Items which have been specified as custom or bid source shall be commercial
quality and require submission of shop drawings, samples, manufacturer's
specifications and/or finish samples to the designer for approval prior to
application or fabrication.
2. When field measurements are required for a custom item they are the
responsibility of the fabricator. If the fabricator is unable to comply with this
requirement, it becomes the Owner's responsibility to furnish field measurements.
3. Bid source should be from the approved vendors listed in Sections 3.0, 4.0, 6.0,
7.0, 8.0, 9.0. If bids have been received prior to issuance of drawings, they will
0.10-2
Gensler = 13.7042.000
G. Item Quantity
1. Furniture and accessory quantities indicated on the specifications are per exact
floor plan count and shall be verified by the Owner or the Purchasing Agent.
Purchasing Allowance has not been made for spares or surplus unless noted
otherwise.
2. Quantities indicated for finishes are based on Interior Designer's estimates and
shall be verified by the designated installer.
3. Client and/or its Purchasing Agent are solely responsible for quantities.
Items requiring Flame Spread Certificates for City Occupancy Permits are
indicated on the specification. Copies of the Flame Spread Certificates should be
requested on purchase orders and kept on file by the Purchasing Agent while
work is in progress. When work is complete, the certificates should be
forwarded to the Owner along with a sample of the material to facilitate
identification.
I. Item Availability
The items specified in this package require varying amounts of time for
manufacture and delivery. Manufacturing and delivery time shall be verified and
coordinated by the Purchasing Agent in coordination with the Owner's schedule
J. Delivery Identification
Each crate, carton and package of furnishings shall be plainly tagged or marked
on the exterior with an identification of the items according to the designer's code
as follows:
Example:
AUD- 401 (mark)
ARM CHAIR (item)
AUDITING ROOM (location)
2/24 (number in carton/number purchased)
K. Decorative Lighting
L. Fabric Cuttings
0.10-3
Gensler = 13.7042.000
Purchasing Agent is responsible for receiving fabric cuttings for dye lot & fabric
finish treatment approval. Submit fabric cuttings to Gensler for approval prior to
purchasing fabric.
2. Approved Bidders
1. Kiesling & Hess Co.
300 West Bristol Street
Philadelphia, PA 19140
215/457-0906
3. Schneider Banks
1108 Commercial St.
Athens, TX 75751
983-675-1440
O. Purchase Orders
Purchasing Agent is required to submit purchase orders to designer for review.
P. Revisions
Specific revised information will be marked by bubbling and a delta symbol with
revision number.
Q. Item Cost
All costs denoted within the FF&A Specifications are net cost only. Costs do not
include tax, freight, crating, etc.
0.10-4
Gensler = Project
7/16/2010 Job #10.6104.000
Requirements for flame ratings of all specified furnishings and finishes within
this booklet are as follows:
Re: Attachment A
0.20-1
Gensler = Project
7/16/2010 Job #10.6104.000
0.21 ATTACHMENT A
=
=
=
fåëÉêí=äçÅ~ä=ÑáêÉ=ÅçÇÉë=áÑ=~î~áä~ÄäÉ=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
0.40-1
Gensler = CSI-Org Projects
13.7042.430
FLOORCOVERING
3. Heat, light, power, and elevator service shall be provided by the owner at no expense to
the Installation Contractor. Neither the owner, operator or purchasing agent shall bear
any responsibility or liability for the loss, theft, and destruction of equipment, tools or
materials belonging to the installation contractor.
7. Carpet specified by Gensler must meet all ADA and minimum-testing requirements as
stated for commercial applications by the CRI.
B. General Requirements
2. The Manufacturer is responsible for submitting samples of all custom carpets and/or
substitutions. Designer's approval must be received before fabrication.
3. All carpet items are to be plastic wrapped and tagged with Designer's item mark number
ready for freight. Materials shall be stored under cover in a dry, ventilated area,
protected from damage, dirt, stains, and moisture until shipping.
5. Custom carpet not produced as a standard item shall be preceded by the submission of a
carpet sample or strike-off. Manufacturer must submit a sample to the designer for
review and written approval prior to purchasing, manufacturing and installation of total
quantity.
6. The Manufacturer shall notify the Purchasing Agent immediately in writing if any
conditions exist which will prevent him from producing satisfactory finished work. The
beginning of fabrication will indicate his acceptance of products.
1.10-1
Gensler = CSI-Org Projects
13.7042.430
A. General Note
The bidders listed below are approved by Gensler based on previous work experience.
Gensler assumes no responsibility for recommendation. If purchasing agent would like
to add to the bid list, submit brochure of proposed new bidders and client reference list to
Gensler. Gensler will require samples as specified.
1. N/A
2. N/A
3. N/A
1.20-1
Gensler = CSI-Org Projects
13.7042.430
Metal finishes must have clear matte coating, rust inhibitor primer, baked enamel or
powder coat finish for humidity protection to prevent rust and corrosion. Manufacture to
ensure materials are non-corrosive and are suitable for use in high humidity and salt air
locations as required.
=
=
=
8.20 -2
Gensler = CSI-Org Projects
13.7042.430
A. Scope
3. Contractor is fully responsible to coordinate his work with the designer's drawings, on-
site conditions in terms of dimensions, limitations and any other variables affecting
installation.
5. General contractor to provide appropriate block fillers, primers, undercoats, and finish-
coat materials that are compatible with one another and with the substrate.
B. General Requirements
1. Insurance coverage in amounts meeting with the Owner's approval shall be carried by the
Contractor installer for the life of the contract and certificate of coverage will be provided
to purchasing agent. This includes, but is not limited to, Workman's Compensation,
Property Insurance & General Liability including Products Liability, Bodily Injury and
Property Damage.
3. All carpet is to be delivered to the Contractor in the original factory wrappings with each
roll denoting its item mark number. The carpet shall be stored in a dry, ventilated area,
protected from damage, dirt, stains, and moisture.
4. Quantities indicated in the specifications are estimates only. Contractor must verify and
provide all quantities required to purchasing agent. Contractor is responsible for any
shortages or overages over 5%.
1. The Contractor shall notify the Purchasing Agent in writing of any conditions which will
prevent him from producing satisfactory work. The installation of carpet will indicate his
acceptance of substrate and he will automatically assume the responsibility for any
unacceptable finished work caused by substrate conditions.
2. Surface Preparation
All surfaces to receive carpet shall be thoroughly clean and dry and in a condition
satisfactory to the Contractor. The Contractor shall notify the Purchasing Agent in
writing of any conditions, which will prevent him from producing satisfactory finished
work. The installation of carpet shall be an indication of his acceptance of the substrates
1.30-1
Gensler = CSI-Org Projects
13.7042.430
and he will automatically assume the responsibility for any unacceptable finished work
caused by substrate conditions.
3. Surface Transitions
Where carpet meets tile or other hard surface flooring, carpet pile height should be
approximately 1/8" higher than the other material. This may require elimination of
padding, feathering of padding or build up of padding or subflooring.
5. Pad Installation
6. Seams (General)
a. Plan seam locations so that no perpendicular seams shall occur at doorways or entries
or high traffic pivotal areas.
b. All seams should run with the flow of traffic.
c. Doorway seams should be centered directly under door.
a. Carpet shall be installed with a tackless strip fastened to the floor at the perimeter
walls leaving a margin or tuck space equal to about 2/3 of carpet thickness.
- Seal all cut edges with a latex adhesive before seaming.
b. Seams
- Shall be hand sewn (unless noted otherwise) and the backside of carpet seam
shall be coated with latex adhesive.
- Shall lay flat and be free from puckering and peaking.
- Shall be straight and matched in every respect.
c. Pad to be a natural or synthetic hair and jute 40 oz. minimum.
a. Carpet shall be installed with a tackless strip fastened to the floor at the perimeter
walls leaving a margin or tuck space equal to about 2/3 of the carpet thickness.
b. Carpet pad to be a synthetic hair and jute, high-density urethane foam or rubber
minimum 40 oz. weight.
c. Seams
1.30-2
Gensler = CSI-Org Projects
13.7042.430
a. All carpet edges must be trimmed and sealed with a latex adhesive so that the base of
face yarns are totally sealed to prevent raveling at seams.
b. Carpet shall be installed using a latex adhesive which is spread onto floor with the
appropriate size trowel for the carpet backing being used. This adhesive should be
applied evenly in sweeping semi-circular motions.
c. Carpet should be rolled with a 35-75 pound roller in both directions for jute or
synthetic backed goods.
a. Seams - Use seam tape and latex seam sealer on all seams. Do not use silicone
treated hot melt tape. All glue direct seams require latex seam sealer.
b. Visually check for pattern match before gluing down. It may be necessary to power
stretch and stay nail certain areas for proper alignment.
c. Pad - Shall be a firm commercial cushion such as (Daltonian) or a flat rubber (Tred
Mor). Use only pads designed for this installation method.
d. Adhesive - use only manufacturer recommended adhesives and spread rates.
D. Clean-up
After the installation of the (individual area) work is complete, areas shall be cleared of
excess materials, and left in broom-clean condition. All leftover carpet shall be bundled,
identified and turned over to the Owner/Operator or his Project Manager.
E. Superintendence
All work shall be done under the direction of the Contractor's capable superintendent,
who shall have had 5 years experience in this type of work and with projects of
comparable scope. The superintendent shall give direction for installation and inspect the
work, as it is being done and after it is completed. Without waiting for orders to do so,
he shall direct correction of all faulty workmanship he may encounter. He shall direct the
installation with prior consent and approval of the Owner.
F. Guarantee
All materials and work provided by the Contractor shall be guaranteed by him against
defects in installation, materials and workmanship for a period of one (1) year from the
date of installation. Any adjustments to the installation, due to defects in installation,
materials and/or workmanship, shall be made within one (1) year from date of installation
at no extra charge. =
1.30-3
Gensler = CSI-Org Projects
13.7042.430
WALLCOVERING
A. Scope
2. Manufacturer is fully responsible for coordination of work with designer's specifications, lead
time quotes to purchasing agent and any other variables affecting fabrication and ready to
ship completion of items.
3. Heat, light, power, and elevator service shall be provided by the owner at no expense to the
Installation Contractor. Neither the owner, operator or purchasing agent shall bear any
responsibility or liability for the loss, theft, and destruction of equipment, tools or materials
belonging to the installation contractor.
B. General Requirements
3. Printing, dyeing, and finishing methods must be appropriate for use on wallcovering.
4. Manufacturer to provide dye lot sample cutting of wallcovering (from current stock) for
review and written approval by Gensler prior to purchasing, manufacturing and installation of
total quantity.
8. Custom wallcovering not produced as a standard item shall be preceded by the submission of
a sample to the designer for review and written approval prior to purchasing, manufacturing,
and installation of total quantity.
9. The Manufacturer is responsible for submitting samples of all custom wallcoverings and/or
substitutions. Designer's approval must be received before fabrication.
10. All wallcovering items are to be plastic wrapped and tagged with Designer's item mark
number ready for freight. Materials shall be stored under cover in a dry, ventilated area,
protected from damage, dirt, stains and moisture until shipping.
2.10-1
Gensler = CSI-Org Projects
13.7042.430
11. The Manufacturer shall notify the Purchasing Agent immediately in writing if any conditions
exist which will prevent him from producing satisfactory finished work. The beginning of
fabrication will indicate his acceptance of products. Manufacturer will automatically assume
responsibility for any unacceptable finished work caused by faulty materials.
2.10-2
Gensler = CSI-Org Projects
13.7042.430
A. General Note
The bidders listed below are approved by Gensler based on previous work experience.
Gensler assumes no responsibility for recommendation. If purchasing agent would like to
add to the bid list, submit brochure of proposed new bidders and client reference list to
Gensler. Gensler will require samples as specified.
1. N/A
2. N/A
3. N/A
2.20-1
Gensler = CSI-Org Projects
13.7042.430
A. Scope
The Installation Contractor (referred to as Contractor throughout the rest of this specification)
shall provide all labor, adhesives, tools, ingrain lining paper (where specified.), etc.,
necessary to properly prepare surface and install wallcoverings as herein specified. The Con-
tractor shall make himself fully responsible for coordination of his work with the designer's
drawings and on-site conditions in terms of dimensions, limitation, and all other variables
affecting proper installation. Contractor must use a manufacturer approved installation.
B. General Requirements
1. Insurance coverage in amounts meeting with the Owner's approval shall be carried by the
Contractor for the life of the contract, and a certificate of such coverage will be provided to
the purchasing agent. This includes, but is not limited to, Worker's Compensation, Property
Insurance, and General Liability including products liability, bodily injury and property
damage.
2. Refer to interior finish plans and elevations for location of specified wallcoverings.
3. All wallcoverings are to be delivered to the Contractor in the original factory wrappings with
each roll denoting its item mark number. The wallcoverings shall be stored in a dry
ventilated area, protected from damage, dirt, stains and moisture.
4. Quantities indicated in the specification are estimates only. Contractor must verify and
provide all quantities required to purchasing agent.
1. The Contractor shall notify the Purchasing Agent in writing of any conditions which will
prevent him from producing satisfactory work. The installation of wallcoverings will indicate
his acceptance of substrate and he will automatically assume the responsibility for any
unacceptable finished work caused by substrate conditions.
2. Surface Preparation
- General: All surfaces must be clean dry smooth and structurally sound. Remove all
free dust, dirt, grease, crayon, ball point ink, wheat and/or loose paint chips.
The moisture content of plaster and masonry surfaces should be a maximum
of 4% as measured with a reliable moisture meter. Contractor to assume
responsibility in preparing all surfaces for appropriate techniques and
adhesives and installation methods as required by manufacture prior to
installation.
- Renovation: All surfaces shall first be properly prepared; removing any old wallcoverings,
peeling or blistered paint, etc., cutting-out and point-up all apparent cracks;
sanding surfaces, and applying a coat of sealer if required.
2.30-1
Gensler = CSI-Org Projects
13.7042.430
3. If indicated in the attached individual specification sheets, surfaces are then to be covered
with an ingrain lining paper.
4. Vinyl & paper wallcovering shall be installed using overlapping and trimming method, or
butt joined, as appropriate, unless noted otherwise.
6. All wallcoverings shall be free of puckering and shall lie flat, without wrinkles or twists.
7. All seams must be made at least six inches from outside and inside corners. Horizontal seams
will not be accepted. All seams are to be thoroughly rolled and cleaned of adhesive.
8. Contractor to provide appropriate block fillers, primers, undercoats, and finish coat materials
that are compatible with one another and with the substrate.
D. Clean-up
After the installation of the (individual area) wallcovering is complete, areas shall be cleared
of excess materials, and left in broom-clean condition. All leftover wallcoverings shall be
bundled, identified and turned over to the Owner/Operator or his Project Manager.
E. Superintendent
All work shall be done under the direction of the Contractor's capable superintendent, who
shall have had 5 years experience in this type of work and with projects of comparable scope.
The superintendent shall give direction for installation and inspect the work, as it is being
done and after it is completed. Without waiting for orders to do so, he shall direct correction
of all faulty workmanship he may encounter. He shall direct the installation with prior
consent and approval of the Owner.
F. Guarantee
All materials and work provided by the Contractor shall be guaranteed by him against defects
in installation materials and workmanship for a period of one (1) year from the date of
installation. Any adjustments to the installation, due to defects in installation, materials
and/or workmanship, shall be made within one (1) year from date of installation at no extra
charge.
2.30-2
Gensler = CSI-Org Projects
13.7042.430
CASEGOODS
A. Scope
B. General Requirements
4. Site conditions are to be reviewed prior to fabrication. Built-in and built-on site
items shall be field dimensioned. Items shall be the maximum wall-to-wall
length possible or evenly sectioned as required. All built-in it3ems must fit
tightly and be leveled during installation to coordinate with existing conditions.
5. All finished items are to be blanket wrapped, ready for freight unless directed
otherwise by Purchasing Agent. If Contractor is to supply crating, the
Purchasing Agent will indicate this and Contractor will charge accordingly.
Materials and completed items shall be stored under cover in dry, well ventilated
spaces, protected from damage, dirt, stains and moisture.
3.10-1
Gensler = CSI-Org Projects
13.7042.430
6. The Contractor shall notify the Purchasing Agent immediately in writing if any
conditions exist which will prevent him from producing satisfactory finished
work. Contractor will automatically assume responsibility for any unacceptable
finished work caused by faulty materials.
1. General Requirements:
a. Casework shall conform to the highest commercial standards, shall
reflect details shown on drawings and shall be fabricated in accordance
with the Architectural Woodwork Institute as follows: Wood Casework
shall be AWI Premium Grade; Plastic Laminate Clad Casework shall be
AWI Custom Grade. Wood construction is to be selected, seasoned,
kiln-dried, and worm-free lumber.
b. All major joints are to be doubled doweled, glued, and screwed with
accurately fitted joints, corners, and miters. Glue stains are
unacceptable. Exposed surfaces shall be free from dents, tools marks,
warping, buckling and open joints. Surfaces exposed to view should not
be stamped on, printed on or marked with identification labels.
c. Joints shall be splined, mortise and tenoned, tongue and grooved, or
double dowelled. Joints shall be full length blocked, glued, and screwed
in two directions, following the best practice of construction. All work
shall be carefully corner-blocked, well fitted, glued and reinforced with
wood screws. Glued stains are unacceptable. Joints on horizontal
surface to be moisture proof to ensure against liquid seepage into frame.
d. Hardwood plywood shall be constructed according to the requirements of
commercial standards. All face veneers shall be matched for color and
grain to present a uniform appearance. When back veneers are of
different species than face, they shall be of the same density and
thickness.
e. Drawers to have clean and smooth interiors sanded, waxed and sealed.
Manufacturer to provide heavy-duty commercial drawer glides with
stops. Drawer joints to be even and smooth, dovetailed or dado joined.
Manufacturer to coordinate locks and lock sequencing for all casegoods
and furniture as required.
f. Interior cavities (i.e. cabinets, shelves, drawers, etc.) are to be fully
finished by manufacturer unless specified otherwise.
g. Manufacturer to provide vented back panels and grommet holes for all
interior equipment as required. All sizes and dimensions of equipment to
be determined based on specifications.
h. All materials used in the finishing of furniture shall be of the highest
quality standard. Each step of the work shall be thoroughly sanded,
smoothed, and cleaned before any finish is applied. Finishes to be of
highest-grade catalyzed lacquer resistant to water, alcohol, and chemical
stains. All exposed members shall be made to conform as specified, in
color and finish. In production, finish needs to be consistent and smooth
with no rough edges. A sample must be submitted to Gensler for written
approval prior to purchasing, manufacturing, and finishing total
quantities.
3.10-2
Gensler = CSI-Org Projects
13.7042.430
a. Cabinet Parts
Exposed Surfaces include exposed faces of drawer and doors when
closed and exposed exterior ends and tops of cabinets less than 72"
above finish floor.
d. Hardware
Provide full-extending ball-bearing roller type drawer guides and appropriate
hinges, pulls, latches, etc., to provide proper casework function. All
hardware is to be reviewed and approved by Interior Designer prior to
installation. Also, provide nylon adjustable levelers at base and/or legs.
a. Cabinet Parts
Exposed Surfaces include surfaces visible when drawers and opaque doors
are closed, areas behind glass doors, bottoms of cabinets 42" or more above
finish floor and tops of cabinets below 78" above finish floor.
Semi-Exposed Surfaces are surfaces which become visible when drawers are
extended, when opaque doors are opened (including backs of doors), bottoms
of cabinets more than 30" above finish floor and less than 42", and tops of
cabinets 78" or more above finish floor when visible from above.
Concealed Surfaces are surfaces not normally visible after installation and
surfaces less than 30" above finish floor.
b. Surface Requirements
Refer to particular casegood specification for wood species. Material grade
for exposed transparent finish to be Grade I, exposed opaque finish to be
Grade II, semi-exposed transparent finish to be Grade II, semi-exposed
opaque finish to be Grade III (Exception: Grade II for panel products), and
Grade IV for concealed surfaces (based on AWI grade). Solid wood is
required for exposed outside corners and similar abuse locations. Solid wood
to be a minimum of 3/4" thick unless noted otherwise (Exception: Drawer
sides, backs, and subfronts may be 1/2" thick and drawer bottoms may be
1/4" thick, U.N.O.). Hardwood veneer plywood complying with CS3561,
Type II; core-veneer, lumber or wood chip may be used in lieu of hardwood
in locations not likely to receive physical abuse.
Edge treatment for body members, shelves, doors, and drawer fronts to be the
same species as face for transparent finishes, and close grain materials for
opaque finishes. Edge banding to be pressure glued. All edges must be
banded.
c. Joinery and Fastening
3.10-4
Gensler = CSI-Org Projects
13.7042.430
Drawers are to be doweled (maximum 2" spacing) and glued and nailed, lock
shoulder joined and glued and nailed, or doweled and glued. Exposed case
body ends are to be mitred to end (splintered mitre or lock mitre) and glued,
unless noted otherwise. Case body members are to be joined by dado (stop
dado if transparent finish), doweled, or screwed (all glued). Stile and rail
joints shall be blind mortised and tenoned, doweled, or concealed screwed
(all glued).
d. Surface Smoothness
Exposed transparent finish surfaces require sanding with paper no coarser
than 120 grit. Exposed opaque finish surfaces are to be sanded with paper
no coarser than 100 grit. No cross scratches are allowed. Semi-exposed
transparent and opaque finishes are to be sanded with paper no coarser than
100 grit and with cross scratches not to exceed 1/4".
e. Factory Finishing
All casegoods are to be factory finished. Provide the Designer with finish
samples of wood (12" x 12") to match finish supplied by Designer. Finish
process to be a minimum of two coats of sealer plus two coats of lacquer
(30% sheer) unless specified otherwise. Concealed surfaces are to receive
one coat of sealer. All horizontal wood surfaces are to receive an alcohol and
water resistant contract sealer.
f. Hardware
Provide full extending ball-bearing roller type drawer guides and
appropriate hinges, pulls, latches, etc. to provide proper casework function.
All hardware is to be reviewed and approved by Interior Designer prior to
installation. Also provide nylon adjustable levelers at base and/or legs.
D. Clean-Up
Case pieces are to be readied for wrapping by cleaning to remove minor defects
that occurred in production
E. Guarantee
All materials and work provided by the Contractor shall be guaranteed by him
against defects in installation, materials and workmanship for a period of one (1)
year from date of installation. Any adjustments to the installation, materials
and/or workmanship, shall be made within one (1) year from date of installation
at no extra charge.
3.10-5
Gensler = CSI-Org Projects
13.7042.430
A. General Note
The bidders listed below are approved by Gensler based on previous work
experience. Gensler assumes no responsibility for recommendation. If pur-
chasing agent would like to add to the bid list, submit brochure of proposed new
bidders and client reference list to Gensler. Gensler will require samples as
specified.
1. N/A
2. N/A
3. N/A
3.20-1
Gensler = CSI-Org Projects
13.7042.430
UPHOLSTERY
A. Scope
B. General Requirements
3. The Contractor is responsible for submitting shop drawings and samples of all
Finishes, showing all points of design, construction and reinforcement to Gensler
for review and written approval. Fabrication should not take place until the
designer's approval is received.
5. All finished items are to be plastic wrapped and tagged with Designer's item
mark code, ready for freight. If Contractor is to supply crating or blanket
wrapping, the purchasing agent will indicate this and Contractor will charge
accordingly. Materials and completed items shall be stored under cover in dry,
well ventilated spaces, protected from damage, dirt, stains and moisture.
6. The Contractor shall notify the Purchasing Agent immediately in writing if any
conditions exist which will prevent him from producing satisfactory finished
work. The beginning of fabrication will indicate his acceptance of products.
4.10-1
Gensler = CSI-Org Projects
13.7042.430
1. General Note:
Upholstered goods shall conform to the highest commercial standards and shall
reflect details shown on drawings. Parts not specifically identified shall be made
of materials most appropriate for their intended use.
2. Frames
- All wood construction must comply with AWI "Custom Grade" or better
quality standards.
- Frame constructed of five quarter, kiln-dried, worm free, hardwood. Hard-
woods shall be birch, poplar, soft maple, gum or sycamore.
- Frame to be reinforced with corner blocks that are glued and screwed to the
rail.
- All major joints must be double doweled, glued and screwed with accurately
fitted joints, corners and miters.
- Fire retardant construction.
- Provide nylon glides at base and/or legs.
- Glue stains are unacceptable. Exposed surfaces shall be free from dents,
tools, marks, warping, buckling and open joints. Surfaces exposed to view
should not be stamped on, printed on or marked with identification labels.
3. Webbing
- Seats to be of pure jute 4" wide.
- Back to be of pure jute 3 1/2" wide.
- Attach frame as close to 5" centers as possible, tightly stretched, interlaced
with 1" turnover at ends.
4. Springs
- Springs to be hand-tied connecting insulated wire.
- Seat suspension to be no-sag, 8-gauge sinuous wire.
- Universal springs to have lifetime guarantees.
- Tight backs much be constructed with 11-guage, no sag sinuous wire.
5. Filling
- Synthetic hair applied over the burlap and affixed with stitching twine to
prevent shifting.
- Synthetic hair is covered with a muslin cover. The muslin is covered with a
fire retardant barrier fabric. (i.e. Burlington's Sandel.)
6. Cushions
- Constructed of foam or a feather/down pillow with a polydac center core
with spring.
- CMHR foam or equal (meeting Boston Fire Code) to be wrapped with two
layers of 8 oz. sewn dacron and cased in muslin.
- The feather down pillow is to be wrapped with a fire retardant barrier cloth.
- Cushion covers to have non-corrosive zippers as required for cleaning ease.
- Provide extra high crown across all seats.
- Provide conceals security hooks for all loose throw pillows and seat cushions
as required.
4.10-2
Gensler = CSI-Org Projects
13.7042.430
7. Arms
- Wrapped with synthetic hair for firm arm or wrapped with CMHR or equal
for soft arm.
- Covered with muslin and fire retardant barrier fabric.
8. Upholstery
- Back of back and underside are to be sealed with fire retardant barrier fabric
(i.e. Burlington's Sandel).
- All upholstery seams to be flat, non-puckering. Stitching should be
interlocking (safety stitch) with a multi-filament, non-breaking thread.
Finishing materials such as nailheads, single or double welting or gimp will
be indicated on the individual specification.
- All welting to be the same material as adjacent upholstery unless noted
otherwise.
- Frame shall not be apparent under C.O.M.; no visible ribs to be allowed.
9. Exposed Wood
- Provide stain full filled catalyzed lacquer finish to protect wood from burns,
alcohol, water, and chemical stains. In production, finish needs to be
consistent and smooth with no rough edges.
11. Re-Upholstery
- Refinish all upholstered goods as required. Refinished upholstered good
with holes, scratches, and dents are to be filled with wood putty and stained
to match existing wood finish.
- Missing or damaged trim pieces must be replaced to match existing.
D. Clean-up
4.10-3
Gensler = CSI-Org Projects
13.7042.430
E. Guarantee
All materials and work provided by the Contractor shall be guaranteed by him
against defects in installation, materials and workmanship for a period of one (1)
year from date of installation. Any adjustments to the installation, materials
and/or workmanship, shall be made within one (1) year from date of installation
at no extra charge.
4.10-4
Gensler = CSI-Org Projects
13.7042.430
A. The bidders listed below are approved by Gensler based on previous work
experience. Gensler assumes no responsibility for recommendation. If pur-
chasing agent would like to add to the bid list, submit brochure of proposed new
bidders and client reference list to Gensler. Gensler will require samples as
specified.
1. N/A
2. N/A
3. N/A
4.20-1
Gensler = CSI-Org Projects
13.7042.430
WINDOW TREATMENT
A. Scope
1. The Fabrication and Installation Contractor (referred to as Contractor throughout the rest
of this Specification) shall provide all field dimensions, quantity and yardage require-
ments and workmanship to fabricate window treatment and all accessory items and labor
necessary to properly install window treatment with the best industry practices and finest
quality.
2. All materials and method used in the fabrication and installation Contractor (referred to
as Contractor throughout the rest of this Specification) shall provide all field dimensions,
quantity and yardage requirements and workmanship to fabricate window treatment and
all accessory items and labor necessary to properly install window treatment with the best
industry practices and finest quality.
3. Contractor is fully responsible to coordinate his work with the designer's drawings, on-
site conditions in terms of dimensions, limitations and any other variables affecting
fabrication and installation.
4. Contractor is responsible for providing purchasing agent with fabric quantities required to
complete the job. Contractor is responsible for any discrepancies between window
treatment dimensions and field dimensions. Contractor is responsible for all material
quantity shortages and any overages in excess of 5%. Actual site measurements must be
obtained prior to fabrication of window treatment fabrications. Each room within an area
specified is to be measured individually.
5. Fabricator must provide all necessary contract quality hardware for complete and finished
installation. Gensler recommends one of the following: Graber, Kirsh, or equal. Installer
shall verify and confirm fit, size and ease of operation of all treatments, track devices, or
mechanisms.
6. Heat, light, power, and elevator service shall be provided by the owner at no expense to
the Installation Contractor. Neither the owner, operator or purchasing agent shall bear
any responsibility or liability for the loss, theft, and destruction of equipment, tools or
materials belonging to the installation.
B. General Requirements
2. Insurance coverage in amounts meeting with the Owner's approval shall be carried by the
Contractor for the life of the contract and a certificate of coverage will be provided to the
purchasing agent. This includes, but is not limited to, Workman's Compensation,
Property Insurance, and General Liability including products liability, bodily injury and
property damage.
5.10-1
Gensler = CSI-Org Projects
13.7042.430
3. The areas to have window treatment are indicated on the Construction Drawing Furniture
Plans and in the FF&A specification sheets. The window treatment contractor shall
submit an elevation and section (shop drawings) of each window type to be treated,
showing installation methods, any seaming, over all dimensions of window treatment and
location of operating hardware. No window treatment shall be manufactured or installed
until the designer's approval has been received.
4. All fabrics are to be delivered to the Contractor with proper identification. Fabrics and
finished window treatments shall be stored under cover in dry, well-ventilated spaces,
protected from damage, dirt, stains, and moisture.
5. The contractor shall notify the Purchasing Agent immediately in writing if any conditions
exist which will prevent him from producing satisfactory finished work. The beginning
of fabrication or the start of installation will indicate his acceptance of products and/or
field responsibility for any unacceptable finished work caused by faulty materials or field
conditions.
1. Track and Hardware to be ceiling mounted unless noted otherwise. All hardware to be
heavy duty, cord traversed or baton operated complete with all required components, and
suitable for commercial installation. Install so that no contact occurs between panels and
windows and/or window mechanisms. Track finish to be standard off-white or color as
detailed. Pulleys to be ball bearing. Cord to be #4 Nylon or fiberglass center with all
cotton jacket. Batons to be 30" or 50" clear fiberglass with "D" snap attachment at
master carrier. Overlap masters are all steel with wide shoe glides. Glides are all nylon.
2. All materials to be submitted to Gensler for approval. Submittals include fabric cuttings,
metal or fabric blind samples and cut sheets on hardware. Any lining and/or black-out
fabric to be supplied by Contractor and submitted to designer for approval.
3. All window treatment must meet ASTM Class A standards either inherently or
chemically. Certificates of flammability testing or flame proofing to be delivered to
Purchasing Agent.
4. Where patterns with repeats are specified, material or C.O.M. shall be cut individually
per room to ensure all patterns match at top and bottom.
5. Fabricator shall receive C.O.M., inspect it for flaws, verify quantities and store it until
required. Any damage, flaws or discrepancies in yardage shall be reported to purchasing
agent immediately.
6. Draperies to be fan folded and suitable wrapped in order to avoid any damage during
shipping, transportation or installation. All draperies shall be hand folded and hand tied
on jobsite at time of installation.
7. Wall mounted top treatment to be used with #2 pine full roof board. Hardware shall be
mounted into roof board.
8. Drapery panels to overlap 3" at points where panels meet to ensure no light leakage.
5.10-2
Gensler = CSI-Org Projects
13.7042.430
10. Trimming is to be hand or machines sewn as detailed in specification and shop drawing.
11. Installation includes pressing, steaming, etc. to insure that all window treatments hang
properly and free of creases, wrinkles and/or twists. Installer shall check and verify fit,
size and ease of operation of all drapery and track. Draperies to be fan folded and all
window treatment suitably wrapped to avoid damage in shipping or installation
D. Clean-up
After the installation work is complete, any and all debris resulting from the installation
shall be picked up and removed from site. Any material overages are to be bundled,
tagged, identified and given to Owner.
E. Superintendence
All work both on and off the site shall be done under the direction of the Contractor's
capable superintendent, who shall have had 5 years experience in this type of work and
with projects of comparable scope. The superintendent in the field shall give direction for
installation and inspect the work, as it is being done and after it is completed. Without
waiting for orders to do so, he shall direct correction of all faulty workmanship he may
encounter. He shall direct the installation with prior consent and approval of the owner.
F. Guarantee
All materials and work provided by the Contractor shall be guaranteed by him against
defects in installation, materials and workmanship for a period of one (1) year from date
of installation. Any adjustments to the installation, materials and/or workmanship, shall
be made within one (1) year from date of installation at no extra charge.
A. General Note
5.10-3
Gensler = CSI-Org Projects
13.7042.000
The bidders listed below are approved by Gensler based on previous work experience.
Gensler assumes no responsibility for recommendation. If purchasing agent would like
to add to the bid list, submit brochure of proposed new bidders and client reference list to
Gensler. Gensler will require samples as specified.
1. N/A
2. N/A
3. N/A
1. N/A
2. N/A
3. N/A
5.20-1
Gensler = CSI-Org Projects
13.7042.000
BEDDING
1. Fabricator to measure bed set for exact dimensions prior to fabrication and verify bed set
coordinates with specified items and their dimensions.
2. Purchasing agent to verify with fabricator overall dimensions and size of bed set prior to
purchasing.
3. Bed set material including lining, fill and construction must be flame retardant, pass
cigarette ignition test, and meet all local, state and federal fire codes.
4. Manufacturer must provide materials and parts for assembly. Manufacturer to ensure
materials and parts for assembly are non-corrosive and suitable for use in high humidity
and salt air locations when required.
5. Bed base and frame must provide support at edge or outer perimeter, and at center of
foundation.
6. Bed cover goods must be joined before quilting to ensure proper pattern match. Once
fabric widths are pattern matched, they shall be locked-stitched and quilted together as a
single piece. Quilt designs will then fall evenly across the entire bed face.
8. Custom bedding or those not produced as standard items shall be preceded by the
submission of a preliminary sample. Manufacturer must submit sample to the designer
for review and written approval prior to purchasing, manufacturing and installation of
total quantity.
=
9. Accent Pillows
- Quantities, dimensions, and yardages references by designer's specifications are
general estimates only. Fabricator is responsible for verifying and confirming all
dimensions, quantities, yardages, C.O.M. and material requirements based on pillow
style and specified C.O.M. width and repeat prior to purchasing and manufacturing
total quantity.
- All cushions, foam, and padding must be inherently flame retardate to meet
California Bulletin #117 and all other local, state, and federal code requirements.
- Custom pillows or those not produced as standard items shall be preceded by the
submission of a preliminary sample. Manufacturer must submit sample to the
designer for review and written approval prior to purchasing, manufacturing and
installation of total quantity.=
=
10. Bids shall include:
- Number and type of spaces.
- Number of widths per window.
- Cost per room installed.
- Total cost of fabrication and installation.
- Total cost of freight
- Total cost of tax
5.30-1
Gensler = CSI-Org Projects
13.7042.430
LIGHTING
A. Scope
B. General Requirements
6.10-1
Gensler = CSI-Org Projects
13.7042.430
4. All finished items are to be plastic bubble wrapped & tagged with Designer's
item mark code, ready for freight. If manufacturer is to supply crating or blanket
wrapping, the purchasing agent will indicate this and manufacturer will charge
additionally. Materials and completed items shall be stored under cover in dry,
well ventilated spaces, protected from damage, dirt, stains and moisture.
7. When necessary, manufacturer must provide contractor and the designer with all
wiring requirements and total weight of fixture for any recommended additional
blocking that may be required for permanent surface mounting.
8. The contractor must coordinate with the electrical engineer the exact
specifications on hardwiring, sockets, lamping and ADA requirements to ensure
electrical devices, including hardwire, recessed, and surface mounted fixtures
meet all local, state and federal code requirements. Refer to electrical
engineering drawings for additional requirements and/or notes.
9. Switch location requirements shall comply with the property owner's applicable
standards.
10. Property owner is responsible for purchasing and supplying all lamps (bulbs)
required for all specified fixtures. Lamping requirements must no exceed the
maximum wattage as specified for each fixture.
11. The Manufacturer shall notify the Purchasing Agent immediately in writing if
any conditions exist which will prevent him from producing satisfactory finished
work. The beginning of fabrication will indicate his acceptance of products.
Manufacturer will automatically assume responsibility for any unacceptable
finished work caused by faulty materials.
3. Bases are to be weighed (20 lbs. for floor lamps, 5 lbs. for table lamp) and sealed
with metal cover.
4. Cords are to be a minimum of 8 feet in length and clear in color unless noted
otherwise on specification.
5. Switches are to be a grooved turn type. Mount switch near the base at the back
or side of fixture on all table lamps, unless noted otherwise.
9. All decorative lamp components shall comply with U.L. and other available
safety/performance standards applicable within the projects' municipality for the
use intended and shall conform with all other applicable codes & ordinances.
Certification that decorative light fixture is Underwriters Laboratory approved
and labeled shall be obtained directly by the purchasing agent from the
manufacturer. Purchasing agent is responsible for submitting all necessary
certificates to the property owner.
10. Metal finishes must have clear enamel matte coating, rust inhibitor primer, baked
enamel, or powercoat finish for humidity protection to prevent rust and
corrosion. Manufacturer to ensure materials are non-corrosive and are suitable
for use in high humidity and salt air locations as required.
11. Manufacturer to coordinate with installer total weight of wall mounted lamp for
any additional blocking that may be required to ensure proper anchoring for
permanent surface mounting.
12. The Contractor must coordinate with the manufacturer exact specification on
sockets, lamping and ADA requirements to ensure decorative light fixtures meet
all local, state and federal codes for applicable conditions.
13. Switch location requirements shall comply with the property owner's applicable
standards.
14. Property owner is responsible for purchasing and supplying all lamps (bulbs)
required for all specified fixtures. Lamping requirements must not exceed the
maximum wattage as specified for each fixture. Property owner is responsible for
supplying manufacturer with lamp (bulbs) samples to confirm shade and harp
size prior to purchasing and manufacturing total quantity.
15. Custom decorative light fixtures for those not produced as standard items shall be
preceded by the submission of shop drawings. Manufacturer must submit shop
drawings and samples of all finishes to the designer for review and written
approval prior to purchasing, manufacturing and installation of total quantity.
16. Fixtures, components & ballasts shall comply with U.L standards and other
available safety/performance standards applicable within the projects
municipality for the use intended and shall conform with all other applicable
codes & ordinances. Certification that architectural light fixtures is Underwriters
Laboratory approved and labeled shall be obtained directly by the purchasing
agent from the manufacturer. The purchasing agent is responsible for submitting
all necessary certificates to property owner.
D. Guarantee
6.10-3
Gensler = CSI-Org Projects
13.7042.430
All materials and work provided by the Contractor shall be guaranteed by him
against defects in installation, materials and workmanship for a period of one (1)
year from date of installation.
Any adjustments to the installation, materials and/or workmanship, shall be made
within one (1) year from date of installation at no extra charge.
6.10-4
Gensler = CSI-Org Projects
13.7042.430
A. General Note
The bidders listed below are approved by Gensler based on previous work
experience. Gensler assumes no responsibility for recommendation. If
purchasing agent would like to add to the bid list, submit brochure of proposed
new bidders and client reference list to Gensler. Gensler will require samples as
specified.
1. N/A
2. N/A
3. N/A
6.20-1
Gensler = CSI-Org Projects
13.7042.430
ARTWORK/MIRRORS
A. Scope
1. The Artwork Consultant or Supplier (referred to as Contractor throughout the rest of this
specification) shall provide required framing including any or all necessary items needed
to complete the job. Workmanship should follow industry practices and be of the finest
quality.
B. General Requirements
2. Insurance coverage in amounts meeting with the Owner's approval shall be carried by the
Contractor for the life of the contract, and a certificate of such coverage will be provided
to the purchasing agent. This includes, but is not limited to, Worker's Compensation,
Property Insurance, and General Liability including products liability, bodily injury and
property damage.
3. Contractor is responsible for supplying the necessary items required for the appropriate
means of security mounting artwork. (Re: Artwork Installation 5.2).
4. All finished items are to be plastic bubble wrapped & tagged with Designer's item mark
code, ready for freight. If Contractor is to supply crating or blanket wrapping, the
purchasing agent will indicate this and Contractor will charge additionally. Materials and
completed items shall be stored under cover in dry, well ventilated spaces, protected from
damage, dirt, stains and moisture.
5. The Contractor shall notify the Purchasing Agent immediately in writing if any
conditions exist which will prevent him from producing satisfactory finished work.
Contractor will automatically assume responsibility for any unacceptable finished work
caused by faulty materials.
7. Custom artwork or those not produced as standard items shall be preceded by the
submission of a sample. Manufacturer must submit a sample of mat, frame, finish, and
art to the designer for review and written approval prior to purchasing, manufacturing
and installation of total quantity.
10. Installer to be responsible for providing necessary and required security mounted
hardware appropriate for wall condition and weight of mirror for complete and finished
installation. Security mounting hardware must meet property standards.
11. Custom mirrors or those not produced as standard items shall be preceded by the
submission of a preliminary sample. Manufacturer must submit sample to the designer
for review and written approval prior to purchasing, manufacturing and installation of
total quantity.
Materials & equipment, as well as workmanship, shall conform to the highest commercial
standards and shall be as specified and/or as indicated on the drawings. Parts not
specifically identified shall be made of materials most appropriate for their intended use.
1. Mounting Techniques
a. Artwork shall be mounted and framed using the most appropriate museum
quality procedures and techniques. Those techniques are to include acid-free
matting and non-adhesive tape as required.
2. Glass
3. Framing Techniques
D. Guarantee
All materials and work provided by the Contractor shall be guaranteed by him against
defects in installation materials and workmanship for a period of one (1) year from date
of installation. Any adjustments to the installation materials and/or workmanship, shall
be made within one (1) year from date of installation at no extra charge.
7.10-2
Gensler = CSI-Org Projects
13.7042.430
A. Typical Guestroom
1. The method of securing to the wall shall be a beveled wood cleat, width to be 3/4 the size
of the artwork being bolted to the wall. For securing installation the installer shall use
Cyano Acrylate (epoxy) on top edge cleat or back edge of wood frame liner. This is a
permanent installation.
2. An alternate method using silicon glue will be an adhesive, which stabilizes the framed
artwork, but can be removed with applied pressure. The manufacturer is to be
responsible for providing additional silicone in high humidity locations. If using
concealed security mounting hardware, the hardware must be appropriate to the size of
the artwork and suitable for field and wall conditions.
B. Public Area
7.20-1
Gensler = CSI-Org Projects
13.7042.430
ACCESSORIES
A. General Requirements
1. Manufacturer to provide screws, plugs, silicone, or security mounting hardware for
complete and finished installation. Concealed screws, plugs, silicone or security
mounting hardware muse be appropriate to size of accessory and suitable for field and
wall conditions.
3. Manufacturer must provide owner with amenity product manual, installation guidelines,
and maintenance instructions in addition to warranties if applicable.
4. Custom accessories or those not produced as standard items shall be preceded by the
submission of a preliminary sample. Manufacturer must submit sample to the designer
for review and written approval prior to purchasing, manufacturing and installation of
total quantity.
SHOWER CURTAINS
8.20 -1
FF&E SPECIFICATIONS LEGEND
Hardware 200-299
Lighting 600-699
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-6) Auditing Desk
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 AUD-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-300
Project #: 13.7042.430 Item Description: (D-6) Auditing Desk 2
Issue Date: 07/30/10 Area Name: Auditing Room
Page 2 AUD-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 1
Issue Date: 07/30/10 Area Name: Auditing Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 AUD-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 2
Issue Date: 07/30/10 Area Name: Auditing Room
Page 2 AUD-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 3
Issue Date: 07/30/10 Area Name: Auditing Room
1E+02
Page 3 AUD-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 4
Issue Date: 07/30/10 Area Name: Auditing Room
1E+02
Page 4 AUD-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0291
Issue Date: 07/30/10 Area Name: Auditing Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 AUD-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0292
Issue Date: 07/30/10 Area Name: Auditing Room
Page 2 AUD-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-400.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0293
Issue Date: 07/30/10 Area Name: Auditing Room
1E+02
Page 3 AUD-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-401
Project #: 13.7042.430 Item Description: (S-13) PC Chair - Stratus 1
Issue Date: 07/30/10 Area Name: Auditing Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Page 1 AUD-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-401
Project #: 13.7042.430 Item Description: (S-13) PC Chair - Stratus 2
Issue Date: 07/30/10 Area Name: Auditing Room
Page 2 AUD-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-401
Project #: 13.7042.430 Item Description: (S-13) PC Chair - Stratus 3
Issue Date: 07/30/10 Area Name: Auditing Room
1E+02
Page 3 AUD-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-401.1
Project #: 13.7042.430 Item Description: (S-13) COM - Destiny 1
Issue Date: 07/30/10 Area Name: Auditing Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 AUD-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-401.1
Project #: 13.7042.430 Item Description: (S-13) COM - Destiny 3
Issue Date: 07/30/10 Area Name: Auditing Room
1E+02
Page 3 AUD-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-900
Project #: 13.7042.430 Item Description: (T-13) Bariatric Table 1
Issue Date: 07/30/10 Area Name: Auditing Room
Instructions:
• Refer to Preamble Section 0.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 AUD-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: AUD-900
Project #: 13.7042.430 Item Description: (T-13) Bariatric Table 2
Issue Date: 07/30/10 Area Name: Auditing Room
1E+02
Page 2 AUD-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CC-900
Project #: 13.7042.430 Item Description: Comm Centers - CC-01 1
Issue Date: 07/30/10 Area Name: Communication Centers
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• Purchasing Agent is solely responsible for coordination of all sizing and content requirements.
Page 1 CC-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CC-900
Project #: 13.7042.430 Item Description: Comm Centers - CC-01 2
Issue Date: 07/30/10 Area Name: Communication Centers
1E+02
Page 2 CC-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CC-901
Project #: 13.7042.430 Item Description: Comm Centers - CC-04 1
Issue Date: 07/30/10 Area Name: Communication Centers
Page 1 CC-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CC-901
Project #: 13.7042.430 Item Description: Comm Centers - CC-04 2
Issue Date: 07/30/10 Area Name: Communication Centers
1E+02
Page 2 CC-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-300
Project #: 13.7042.430 Item Description: Banquet Table, Round 1
Issue Date: 07/30/10 Area Name: Chapel
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs and renderings of specified items contained in this specification package are for general
design intent and reference only.
• All materials and construction must be of contract quality.
Page 1 CPL-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-300
Project #: 13.7042.430 Item Description: Banquet Table, Round 2
Issue Date: 07/30/10 Area Name: Chapel
Page 2 CPL-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-300
Project #: 13.7042.430 Item Description: Banquet Table, Round 3
Issue Date: 07/30/10 Area Name: Chapel
1E+02
Page 3 CPL-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-400
Project #: 13.7042.430 Item Description: (S-19) Chapel Chair - Guest Chair 1
Issue Date: 07/30/10 Area Name: Chapel
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 CPL-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-400
Project #: 13.7042.430 Item Description: (S-19) Chapel Chair - Guest Chair 2
Issue Date: 07/30/10 Area Name: Chapel
Page 2 CPL-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-400
Project #: 13.7042.430 Item Description: (S-19) Chapel Chair - Guest Chair 3
Issue Date: 07/30/10 Area Name: Chapel
1E+02
Page 3 CPL-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-400.1
Project #: 13.7042.430 Item Description: (S-19) COM - Fall Song 1
Issue Date: 07/30/10 Area Name: Chapel
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 CPL-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPL-400.1
Project #: 13.7042.430 Item Description: (S-19) COM - Fall Song 3
Issue Date: 07/30/10 Area Name: Chapel
1E+02
Page 3 CPL-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-300
Project #: 13.7042.430 Item Description: (D-11) Staff Desk 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-11) Staff Desk
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-300
Project #: 13.7042.430 Item Description: (D-11) Staff Desk 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-301
Project #: 13.7042.430 Item Description: (T-1) Course Room Table 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-1) Course Room Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-301
Project #: 13.7042.430 Item Description: (T-1) Course Room Table 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-302
Project #: 13.7042.430 Item Description: (T-2) Clay Bin Table 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-2) Clay Bin Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-302
Project #: 13.7042.430 Item Description: (T-2) Clay Bin Table 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-303
Project #: 13.7042.430 Item Description: (T-3) CD Player Table 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-3) CD Player Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-303
Project #: 13.7042.430 Item Description: (T-3) CD Player Table 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-304
Project #: 13.7042.430 Item Description: (T-4) Co--Auditing Table 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-4) Co-Auditing Table
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 CRM-304
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-304
Project #: 13.7042.430 Item Description: (T-4) Co--Auditing Table 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-304
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-305
Project #: 13.7042.430 Item Description: (T-10) Small Course Room Table 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-10) Small Course Room Table
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 CRM-305
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-305
Project #: 13.7042.430 Item Description: (T-10) Small Course Room Table 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-305
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-306
Project #: 13.7042.430 Item Description: (T-14) Key to Life/Orientation Table 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-14) Key To Life/ Orientation Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-306
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-306
Project #: 13.7042.430 Item Description: (T-14) Key to Life/Orientation Table 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-306
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-307
Project #: 13.7042.430 Item Description: (B-9) Supervisor Stand 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (B-9) Supervisor Stand
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-307
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-307
Project #: 13.7042.430 Item Description: (B-9) Supervisor Stand 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-307
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-308
Project #: 13.7042.430 Item Description: (D-8) Counter 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-8) Counter
Includes Components: F-3.4, Cab-15.1, Cab-7, O-1 (Qty 4)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-308
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-308
Project #: 13.7042.430 Item Description: (D-8) Counter 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-308
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-320
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-11.4, B-11.4, B-11.4, F-4.4, Cab-15.3
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-320
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-321
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-321
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-322
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.3, Cab-5.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-322
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-323
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: F-4.3, B-11.3, Cab-15.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-323
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-324
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4 (Qty 3)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-324
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-325
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-11.4, B-11.4, Cab-15.3, B-11.4, B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-325
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-326
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.3
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-326
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-326
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-326
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-327
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.2, B-11.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-327
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-327
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-327
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-328
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-9.2, B-11.3
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-328
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-328
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-328
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-329
Project #: 13.7042.430 Item Description: Partition 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Partition
Includes Components: PW-1 (Qty 4)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-329
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-329
Project #: 13.7042.430 Item Description: Partition 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-329
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-330
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-7, Cab-15.3, B-5.4, Cab-5.3, F-3.4, F-3.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-330
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-330
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-330
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-331
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4, B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-331
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-331
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-331
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-332
Project #: 13.7042.430 Item Description: AV Cabinet 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom AV Cabinet
Includes Components: Cab-12
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-332
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-332
Project #: 13.7042.430 Item Description: AV Cabinet 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-332
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-333
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.3, B-11.3
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-333
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-333
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-333
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-334
Project #: 13.7042.430 Item Description: Filing Cabinet 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Files
Includes Components: F-3.3
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-334
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-334
Project #: 13.7042.430 Item Description: Filing Cabinet 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-334
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-335
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-335
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-335
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-335
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-336
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.3, Cab-7, B-5.4, B-5.4, Cab-5.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-336
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-336
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-336
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-337
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Course Room
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-5.2, Cab-5.1, B-5.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-337
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-337
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-337
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Page 1 CRM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 3
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 3 CRM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 4
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 4 CRM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Fabric - JA029 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 CRM-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Fabric - JA029 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-400.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Fabric - JA029 3
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 3 CRM-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
Page 1 CRM-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 3
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 3 CRM-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 4
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 4 CRM-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-401.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 3
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 3 CRM-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-402
Project #: 13.7042.430 Item Description: (S-14) Stool - Goal Counter 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Page 1 CRM-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-402
Project #: 13.7042.430 Item Description: (S-14) Stool - Goal Counter 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-402
Project #: 13.7042.430 Item Description: (S-14) Stool - Goal Counter 3
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 3 CRM-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-402.1
Project #: 13.7042.430 Item Description: (S-14, Seat)COM - Squash 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-402.1
Project #: 13.7042.430 Item Description: (S-14, Seat)COM - Squash 2
Issue Date: 07/30/10 Area Name: Course Room
Page 2 CRM-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-402.1
Project #: 13.7042.430 Item Description: (S-14, Seat)COM - Squash 3
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 3 CRM-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-900
Project #: 13.7042.430 Item Description: Clay Bin 1
Issue Date: 07/30/10 Area Name: Course Room
Page 1 CRM-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-900
Project #: 13.7042.430 Item Description: Clay Bin 2
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 2 CRM-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-901
Project #: 13.7042.430 Item Description: Clay Tool Bin 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-901
Project #: 13.7042.430 Item Description: Clay Tool Bin 2
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 2 CRM-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-902
Project #: 13.7042.430 Item Description: (T-13) Bariatric Table 1
Issue Date: 07/30/10 Area Name: Course Room
Instructions:
• Refer to Preamble Section 0.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 CRM-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CRM-902
Project #: 13.7042.430 Item Description: (T-13) Bariatric Table 2
Issue Date: 07/30/10 Area Name: Course Room
1E+02
Page 2 CRM-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 1
Issue Date: 07/30/10 Area Name: Dining
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 DIN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 2
Issue Date: 07/30/10 Area Name: Dining
Page 2 DIN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 3
Issue Date: 07/30/10 Area Name: Dining
1E+02
Page 3 DIN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 4
Issue Date: 07/30/10 Area Name: Dining
1E+02
Page 4 DIN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-301
Project #: 13.7042.430 Item Description: Outdoor Dining Table 1
Issue Date: 07/30/10 Area Name: Dining
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 DIN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-301
Project #: 13.7042.430 Item Description: Outdoor Dining Table 2
Issue Date: 07/30/10 Area Name: Dining
Page 2 DIN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-301
Project #: 13.7042.430 Item Description: Outdoor Dining Table 3
Issue Date: 07/30/10 Area Name: Dining
2E+02
Page 3 DIN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-400
Project #: 13.7042.430 Item Description: (S-18) Dining Chair - Side Chair 1
Issue Date: 07/30/10 Area Name: Dining
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
Page 1 DIN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-400
Project #: 13.7042.430 Item Description: (S-18) Dining Chair - Side Chair 2
Issue Date: 07/30/10 Area Name: Dining
Page 2 DIN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-400
Project #: 13.7042.430 Item Description: (S-18) Dining Chair - Side Chair 3
Issue Date: 07/30/10 Area Name: Dining
1E+02
Page 3 DIN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-401
Project #: 13.7042.430 Item Description: (S-14) Stool - Counter Stool 1
Issue Date: 07/30/10 Area Name: Dining
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 DIN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-401
Project #: 13.7042.430 Item Description: (S-14) Stool - Counter Stool 2
Issue Date: 07/30/10 Area Name: Dining
Page 2 DIN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-401
Project #: 13.7042.430 Item Description: (S-14) Stool - Counter Stool 3
Issue Date: 07/30/10 Area Name: Dining
1E+02
Page 3 DIN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-402
Project #: 13.7042.430 Item Description: (S-18) Outdoor Dining Chair 1
Issue Date: 07/30/10 Area Name: Dining
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
Page 1 DIN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-402
Project #: 13.7042.430 Item Description: (S-18) Outdoor Dining Chair 2
Issue Date: 07/30/10 Area Name: Dining
Page 2 DIN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-402
Project #: 13.7042.430 Item Description: (S-18) Outdoor Dining Chair 3
Issue Date: 07/30/10 Area Name: Dining
2E+02
Page 3 DIN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-403
Project #: 13.7042.430 Item Description: (S-16) Outdoor Bench 1
Issue Date: 07/30/10 Area Name: Dining
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
Page 1 DIN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-403
Project #: 13.7042.430 Item Description: (S-16) Outdoor Bench 2
Issue Date: 07/30/10 Area Name: Dining
Page 2 DIN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-403
Project #: 13.7042.430 Item Description: (S-16) Outdoor Bench 3
Issue Date: 07/30/10 Area Name: Dining
2E+02
Page 3 DIN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-900
Project #: 13.7042.430 Item Description: Planter 1
Issue Date: 07/30/10 Area Name: Dining
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 DIN-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DIN-900
Project #: 13.7042.430 Item Description: Planter 2
Issue Date: 07/30/10 Area Name: Dining
1E+02
Page 2 DIN-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-100
Project #: 13.7042.430 Item Description: Area Rug - Tai Ping 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 1.0 for additional requirements.
• Refer to Page 2 for photograph and drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.04
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-100
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-100
Project #: 13.7042.430 Item Description: Area Rug - Tai Ping 2
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 2 DV6-100
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-300
Project #: 13.7042.430 Item Description: (T-5) End Table - Industrial Chest 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 DV6-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-300
Project #: 13.7042.430 Item Description: (T-5) End Table - Industrial Chest 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-300
Project #: 13.7042.430 Item Description: (T-5) End Table - Industrial Chest 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-301
Project #: 13.7042.430 Item Description: (T-6) Cocktail Table - Harmon 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-301
Project #: 13.7042.430 Item Description: (T-6) Cocktail Table - Harmon 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-301
Project #: 13.7042.430 Item Description: (T-6) Cocktail Table - Harmon 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-301.1
Project #: 13.7042.430 Item Description: (T-6) COM Bone 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 DV6-301.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-301.1
Project #: 13.7042.430 Item Description: (T-6) COM Bone 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-301.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-302
Project #: 13.7042.430 Item Description: (T-5) Console Table - Industrial 1
Console
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 DV6-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-302
Project #: 13.7042.430 Item Description: (T-5) Console Table - Industrial 2
Console
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-302
Project #: 13.7042.430 Item Description: (T-5) Console Table - Industrial 3
Console
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-303
Project #: 13.7042.430 Item Description: Custom Table 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Table
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 DV6-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-303
Project #: 13.7042.430 Item Description: Custom Table 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-320
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4 (Qty-6)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-320
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-321
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-321
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-322
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4 (Qty-4)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-322
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-323
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4, B-11.4 (Back to Back)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-323
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400
Project #: 13.7042.430 Item Description: (S-4) Sofa - 2145-S2 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Page 1 DV6-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400
Project #: 13.7042.430 Item Description: (S-4) Sofa - 2145-S2 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400
Project #: 13.7042.430 Item Description: (S-4) Sofa - 2145-S2 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400.1
Project #: 13.7042.430 Item Description: (S-4) COM - Dapper 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 DV6-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400.1
Project #: 13.7042.430 Item Description: (S-4) COM - Dapper 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400A
Project #: 13.7042.430 Item Description: Pillow 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
Page 1 DV6-400A
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400A
Project #: 13.7042.430 Item Description: Pillow 2
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 2 DV6-400A
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400A.1
Project #: 13.7042.430 Item Description: Pillow COM - Chocolate 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 DV6-400A.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-400A.1
Project #: 13.7042.430 Item Description: Pillow COM - Chocolate 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-400A.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-401
Project #: 13.7042.430 Item Description: (S-3) Guest Chair - Assembly 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Page 1 DV6-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-401
Project #: 13.7042.430 Item Description: (S-3) Guest Chair - Assembly 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-401
Project #: 13.7042.430 Item Description: (S-3) Guest Chair - Assembly 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-401.1
Project #: 13.7042.430 Item Description: (S-3) Graded-in - Paper White 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-401.1
Project #: 13.7042.430 Item Description: (S-3) Graded-in - Paper White 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-401.1
Project #: 13.7042.430 Item Description: (S-3) Graded-in - Paper White 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-402
Project #: 13.7042.430 Item Description: Custom Bench 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bench
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 DV6-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-402
Project #: 13.7042.430 Item Description: Custom Bench 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-402.1
Project #: 13.7042.430 Item Description: (S-5, Seat) COM - Nutmeg 1
Issue Date: 07/30/10 Area Name: Div 6 Display
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 DV6-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-402.1
Project #: 13.7042.430 Item Description: (S-5, Seat) COM - Nutmeg 2
Issue Date: 07/30/10 Area Name: Div 6 Display
Page 2 DV6-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: DV6-402.1
Project #: 13.7042.430 Item Description: (S-5, Seat) COM - Nutmeg 3
Issue Date: 07/30/10 Area Name: Div 6 Display
1E+02
Page 3 DV6-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: EQP-900
Project #: 13.7042.430 Item Description: (E-5) Safe 1
Issue Date: 07/30/10 Area Name: Equipment
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 EQP-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: EQP-900
Project #: 13.7042.430 Item Description: (E-5) Safe 2
Issue Date: 07/30/10 Area Name: Equipment
1E+02
Page 2 EQP-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FLM-400
Project #: 13.7042.430 Item Description: (S-11) Guest Chair - Stratus 1
Issue Date: 07/30/10 Area Name: Film Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 FLM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FLM-400
Project #: 13.7042.430 Item Description: (S-11) Guest Chair - Stratus 2
Issue Date: 07/30/10 Area Name: Film Room
Page 2 FLM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FLM-400
Project #: 13.7042.430 Item Description: (S-11) Guest Chair - Stratus 3
Issue Date: 07/30/10 Area Name: Film Room
1E+02
Page 3 FLM-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FLM-400.1
Project #: 13.7042.430 Item Description: (S-11) COM - Cognac 1
Issue Date: 07/30/10 Area Name: Film Room
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 FLM-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FLM-400.1
Project #: 13.7042.430 Item Description: (S-11) COM - Cognac 3
Issue Date: 07/30/10 Area Name: Film Room
1E+02
Page 3 FLM-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDF-900
Project #: 13.7042.430 Item Description: High Density Filing - Various Sizes 1
Issue Date: 07/30/10 Area Name: High Density Filing
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HDF-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDF-900
Project #: 13.7042.430 Item Description: High Density Filing - Various Sizes 2
Issue Date: 07/30/10 Area Name: High Density Filing
1E+02
Page 2 HDF-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDF-901
Project #: 13.7042.430 Item Description: High Density Filing - Various Sizes 1
Issue Date: 07/30/10 Area Name: High Density Filing
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HDF-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDF-901
Project #: 13.7042.430 Item Description: High Density Filing - Various Sizes 2
Issue Date: 07/30/10 Area Name: High Density Filing
2E+02
Page 2 HDF-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDF-902
Project #: 13.7042.430 Item Description: High Density Filing - Various Sizes 1
Issue Date: 07/30/10 Area Name: High Density Filing
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HDF-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDF-902
Project #: 13.7042.430 Item Description: High Density Filing - Various Sizes 2
Issue Date: 07/30/10 Area Name: High Density Filing
2E+02
Page 2 HDF-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-300
Project #: 13.7042.430 Item Description: (T-5) End Table - Nora 1
Issue Date: 07/30/10 Area Name: High Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-300
Project #: 13.7042.430 Item Description: (T-5) End Table - Nora 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-300
Project #: 13.7042.430 Item Description: (T-5) End Table - Nora 3
Issue Date: 07/30/10 Area Name: High Finish Level
1E+02
Page 3 HFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-301
Project #: 13.7042.430 Item Description: Reception Desk 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Reception Desk
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 HFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-301
Project #: 13.7042.430 Item Description: Reception Desk 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-302
Project #: 13.7042.430 Item Description: Credenza 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Credenza
Includes Components: F-3.1, Cab-2.1, Cab-15.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-302
Project #: 13.7042.430 Item Description: Credenza 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-303
Project #: 13.7042.430 Item Description: Reception Desk 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Reception Desk
Includes Components: P-1, Cab-2.1, F-3.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-303
Project #: 13.7042.430 Item Description: Reception Desk 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-320
Project #: 13.7042.430 Item Description: Trophy Case 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Trophy Case
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 HFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-320
Project #: 13.7042.430 Item Description: Trophy Case 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-321
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.2 (Qty-2)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-321
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-322
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4 (Qty-3)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-322
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-323
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-4.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-323
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-324
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4, B-3.4 (Back-to-Back)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-324
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-325
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4 (Qty-2)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HFN-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-325
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 1
Issue Date: 07/30/10 Area Name: High Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 HFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 3
Issue Date: 07/30/10 Area Name: High Finish Level
1E+02
Page 3 HFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-400.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 1
Issue Date: 07/30/10 Area Name: High Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 HFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-400.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-400.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 3
Issue Date: 07/30/10 Area Name: High Finish Level
1E+02
Page 3 HFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-401
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 1
Issue Date: 07/30/10 Area Name: High Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Upholstered seat & back with wood base
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Page 1 HFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-401
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 2
Issue Date: 07/30/10 Area Name: High Finish Level
Page 2 HFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-401
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 3
Issue Date: 07/30/10 Area Name: High Finish Level
1E+02
Page 3 HFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-401.1
Project #: 13.7042.430 Item Description: (S-3) COM - Praline 1
Issue Date: 07/30/10 Area Name: High Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 HFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HFN-401.1
Project #: 13.7042.430 Item Description: (S-3) COM - Praline 3
Issue Date: 07/30/10 Area Name: High Finish Level
1E+02
Page 3 HFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-300
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Brickmaker's Table
1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-300
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Brickmaker's Table
2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-300
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Brickmaker's Table
3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-301
Project #: 13.7042.430 Item Description: RTC Reports Station 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom RTC Reports Station
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 HGC-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-301
Project #: 13.7042.430 Item Description: RTC Reports Station 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-320
Project #: 13.7042.430 Item Description: Combination 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Credenza
Includes Components: B-5.4, Cab-20, B-5.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-320
Project #: 13.7042.430 Item Description: Combination 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-321
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.5 (Qty 3)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-321
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-400
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Lounge chair with ladder back and upholstered seat
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 HGC-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-400
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-400
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-400.1
Project #: 13.7042.430 Item Description: (S-3, Seat) COM - Sarong 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-400.1
Project #: 13.7042.430 Item Description: (S-3, Seat) COM - Sarong 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-400.1
Project #: 13.7042.430 Item Description: (S-3, Seat) COM - Sarong 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-401
Project #: 13.7042.430 Item Description: (S-7) Writing Desk Chair - Custom 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Low back side chair with upholstered seat and wicker back
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 HGC-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-401
Project #: 13.7042.430 Item Description: (S-7) Writing Desk Chair - Custom 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-401
Project #: 13.7042.430 Item Description: (S-7) Writing Desk Chair - Custom 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-401.1
Project #: 13.7042.430 Item Description: (S-7) COM - Squash 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-401.1
Project #: 13.7042.430 Item Description: (S-7) COM - Squash 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-401.1
Project #: 13.7042.430 Item Description: (S-7) COM - Squash 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402
Project #: 13.7042.430 Item Description: (S-4) Sofa - Dansk 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Page 1 HGC-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402
Project #: 13.7042.430 Item Description: (S-4) Sofa - Dansk 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402
Project #: 13.7042.430 Item Description: (S-4) Sofa - Dansk 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402.1
Project #: 13.7042.430 Item Description: (S-4) COM - Nutmeg 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402.1
Project #: 13.7042.430 Item Description: (S-4) COM - Nutmeg 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402.1
Project #: 13.7042.430 Item Description: (S-4) COM - Nutmeg 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402.2
Project #: 13.7042.430 Item Description: Pillow COM - Cumin 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-402.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402.2
Project #: 13.7042.430 Item Description: Pillow COM - Cumin 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-402.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-402.2
Project #: 13.7042.430 Item Description: Pillow COM - Cumin 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-402.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-403
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Bay Club Chair 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 HGC-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-403
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Bay Club Chair 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-403
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Bay Club Chair 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-403.1
Project #: 13.7042.430 Item Description: (S-3)COM - Sumatra 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 HGC-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-403.1
Project #: 13.7042.430 Item Description: (S-3)COM - Sumatra 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-403.1
Project #: 13.7042.430 Item Description: (S-3)COM - Sumatra 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-600
Project #: 13.7042.430 Item Description: Table Lamp - Ktribe 1
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Instructions:
• Refer to Preamble Section 0.0 and 6.0 for additional requirements.
• Refer to attached for Photograph or Drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• Fabricator must review design concept and inform Gensler of any problems or discrepancies prior to fabrication.
• Must be U.L. approved and labeled. Manufacturer responsible for supplying UL approved documentation to the
purchasing agent.
• Metal grade and thickness must be commercial grade and withstand heavy hospitality usage.
Page 1 HGC-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-600
Project #: 13.7042.430 Item Description: Table Lamp - Ktribe 2
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
Page 2 HGC-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HGC-600
Project #: 13.7042.430 Item Description: Table Lamp - Ktribe 3
Issue Date: 07/30/10 Area Name: Hubbard Guidance Center
1E+02
Page 3 HGC-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-300
Project #: 13.7042.430 Item Description: Dining Table - Square Top & Base 4
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 4 LFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-301
Project #: 13.7042.430 Item Description: (D-4) Writing Desk 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-301
Project #: 13.7042.430 Item Description: (D-4) Writing Desk 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-301
Project #: 13.7042.430 Item Description: (D-4) Writing Desk 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-302
Project #: 13.7042.430 Item Description: Dining Table 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-302
Project #: 13.7042.430 Item Description: Dining Table 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-302
Project #: 13.7042.430 Item Description: Dining Table 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-320
Project #: 13.7042.430 Item Description: Nightstand 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-320
Project #: 13.7042.430 Item Description: Nightstand 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-320
Project #: 13.7042.430 Item Description: Nightstand 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-321A
Project #: 13.7042.430 Item Description: Headboard 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-321A
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-321A
Project #: 13.7042.430 Item Description: Headboard 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-321A
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-321A
Project #: 13.7042.430 Item Description: Headboard 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-321A
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-321B
Project #: 13.7042.430 Item Description: Bed Frame 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-321B
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-321B
Project #: 13.7042.430 Item Description: Bed Frame 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-321B
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-321B
Project #: 13.7042.430 Item Description: Bed Frame 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-321B
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-322
Project #: 13.7042.430 Item Description: Chest 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-322
Project #: 13.7042.430 Item Description: Chest 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-322
Project #: 13.7042.430 Item Description: Chest 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-323
Project #: 13.7042.430 Item Description: Dresser 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-323
Project #: 13.7042.430 Item Description: Dresser 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-323
Project #: 13.7042.430 Item Description: Dresser 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-324
Project #: 13.7042.430 Item Description: Armoire 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 LFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-324
Project #: 13.7042.430 Item Description: Armoire 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-324
Project #: 13.7042.430 Item Description: Armoire 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-325
Project #: 13.7042.430 Item Description: Chinese Chart Cabinet 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Chinese Chart Cabinet
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-325
Project #: 13.7042.430 Item Description: Chinese Chart Cabinet 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 LFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400
Project #: 13.7042.430 Item Description: (S-12) Task Chair - Goal Air 4
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 4 LFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0291
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 LFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0292
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-400.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0293
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-401
Project #: 13.7042.430 Item Description: (S-9) Guest Chair - Yos 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 1 LFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-401
Project #: 13.7042.430 Item Description: (S-9) Guest Chair - Yos 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-401.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0291
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 LFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-401.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0292
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-401.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0293
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-402
Project #: 13.7042.430 Item Description: (S-14) Stool - Goal Counter 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Page 1 LFN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-402
Project #: 13.7042.430 Item Description: (S-14) Stool - Goal Counter 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-402
Project #: 13.7042.430 Item Description: (S-14) Stool - Goal Counter 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-402.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0291
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 LFN-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-402.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0292
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-402.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0293
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-402.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-403
Project #: 13.7042.430 Item Description: (S-6) Conference Chair - Goal Air with
1
Arms
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 LFN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-403
Project #: 13.7042.430 Item Description: (S-6) Conference Chair - Goal Air with
2
Arms
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-403
Project #: 13.7042.430 Item Description: (S-6) Conference Chair - Goal Air with
3
Arms
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-403.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0291
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 LFN-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-403.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0292
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-403.1
Project #: 13.7042.430 Item Description: (S-12, Seat) Graded-in Fabric - JA0293
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-404
Project #: 13.7042.430 Item Description: (S-18) Dining Chair 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
Page 1 LFN-404
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-404
Project #: 13.7042.430 Item Description: (S-18) Dining Chair 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-404
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-404
Project #: 13.7042.430 Item Description: (S-18) Dining Chair 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-404
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-405
Project #: 13.7042.430 Item Description: (S-18) Dining Chair 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
Page 1 LFN-405
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-405
Project #: 13.7042.430 Item Description: (S-18) Dining Chair 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-405
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-405
Project #: 13.7042.430 Item Description: (S-18) Dining Chair 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-405
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-406
Project #: 13.7042.430 Item Description: (S-5) Task Chair 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LFN-406
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-406
Project #: 13.7042.430 Item Description: (S-5) Task Chair 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-406
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-406
Project #: 13.7042.430 Item Description: (S-5) Task Chair 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-406
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.1
Project #: 13.7042.430 Item Description: Queen Mattress 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 LFN-500.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.1
Project #: 13.7042.430 Item Description: Queen Mattress 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-500.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.2
Project #: 13.7042.430 Item Description: Queen Sheet Set 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 LFN-500.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.2
Project #: 13.7042.430 Item Description: Queen Sheet Set 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-500.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.3
Project #: 13.7042.430 Item Description: Queen Duvet Insert 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 LFN-500.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.3
Project #: 13.7042.430 Item Description: Queen Duvet Insert 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-500.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.4
Project #: 13.7042.430 Item Description: Queen Pillows 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Style: HOS100PI0020-S
Quilting Thread Content: 50% Cotton, 50% Polyester; 152 Thread Count
Fill: 27oz Siliconized Hollow Core Polyester
Finish Size: 20" x 30"
Edge Detail: Knife Edge
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 LFN-500.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.4
Project #: 13.7042.430 Item Description: Queen Pillows 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-500.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.5
Project #: 13.7042.430 Item Description: Queen Pillow Cases 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 LFN-500.5
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.5
Project #: 13.7042.430 Item Description: Queen Pillow Cases 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-500.5
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.6
Project #: 13.7042.430 Item Description: Queen Duvet Cover and Shams 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 LFN-500.6
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-500.6
Project #: 13.7042.430 Item Description: Queen Duvet Cover and Shams 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-500.6
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-600
Project #: 13.7042.430 Item Description: Table Lamp - Bristal Accordian 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 6.0 for additional requirements.
• Refer to attached for Photograph or Drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• Fabricator must review design concept and inform Gensler of any problems or discrepancies prior to fabrication.
• Must be U.L. approved and labeled. Manufacturer responsible for supplying UL approved documentation to the
purchasing agent.
• Metal grade and thickness must be commercial grade and withstand heavy hospitality usage.
• Metal finishes to have clear enamel matte coating, rust inhibit or primer, baked enamel or powdercoat finish for
Page 1 LFN-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-600
Project #: 13.7042.430 Item Description: Table Lamp - Bristal Accordian 2
Issue Date: 07/30/10 Area Name: Low Finish Level
Page 2 LFN-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-600
Project #: 13.7042.430 Item Description: Table Lamp - Bristal Accordian 3
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 3 LFN-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-900
Project #: 13.7042.430 Item Description: Workbench 1
Issue Date: 07/30/10 Area Name: Low Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 LFN-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LFN-900
Project #: 13.7042.430 Item Description: Workbench 2
Issue Date: 07/30/10 Area Name: Low Finish Level
1E+02
Page 2 LFN-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-100
Project #: 13.7042.430 Item Description: Area Rug - Maori_Small 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 1.0 for additional requirements.
• Refer to Page 2 for photograph and drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.04
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• Exact size and location of inset rugs to be coordinated with General Contractor
Page 1 LRH-100
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-100
Project #: 13.7042.430 Item Description: Area Rug - Maori_Small 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
1E+02
Page 2 LRH-100
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-300
Project #: 13.7042.430 Item Description: Credenza 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Credenza
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 LRH-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-300
Project #: 13.7042.430 Item Description: Credenza 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-302
Project #: 13.7042.430 Item Description: (T-5) End Table 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 LRH-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-302
Project #: 13.7042.430 Item Description: (T-5) End Table 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-302
Project #: 13.7042.430 Item Description: (T-5) End Table 3
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
1E+02
Page 3 LRH-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-320
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 LRH-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-320
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-321
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.3, B-2.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 LRH-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-321
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-322
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.2, B-11.4, Cab-15.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 LRH-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-322
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-400
Project #: 13.7042.430 Item Description: (S-1) Executive Chair - Ataros II 1
Midback
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
Page 1 LRH-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-400
Project #: 13.7042.430 Item Description: (S-1) Executive Chair - Ataros II 2
Midback
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-400
Project #: 13.7042.430 Item Description: (S-1) Executive Chair - Ataros II 3
Midback
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
2E+02
Page 3 LRH-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-400.1
Project #: 13.7042.430 Item Description: (S-1) Graded-In Leather - LP05 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 LRH-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-400.1
Project #: 13.7042.430 Item Description: (S-1) Graded-In Leather - LP05 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-400.1
Project #: 13.7042.430 Item Description: (S-1) Graded-In Leather - LP05 3
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
1E+02
Page 3 LRH-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-401
Project #: 13.7042.430 Item Description: (S-2) Guest Chair - Celon 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 LRH-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-401
Project #: 13.7042.430 Item Description: (S-2) Guest Chair - Celon 2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Page 2 LRH-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-401
Project #: 13.7042.430 Item Description: (S-2) Guest Chair - Celon 3
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
1E+02
Page 3 LRH-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-401.1
Project #: 13.7042.430 Item Description: (S-19) COM - Fall Song 1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 LRH-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-401.1
Project #: 13.7042.430 Item Description: (S-19) COM - Fall Song 3
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
1E+02
Page 3 LRH-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-800
Project #: 13.7042.430 Item Description: Stanchion Set (Rope, Hook, Wall Plate)
1
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
• All parts must be sealed to prevent rust and corrosion.
• Must provide with a suitable sealer to prevent water leakage and discoloration.
Page 1 LRH-800
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: LRH-800
Project #: 13.7042.430 Item Description: Stanchion Set (Rope, Hook, Wall Plate)
2
Issue Date: 07/30/10 Area Name: L. Ron Hubbard Office
1E+02
Page 2 LRH-800
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-300
Project #: 13.7042.430 Item Description: (T-8) Children's Square Table 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 MFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-300
Project #: 13.7042.430 Item Description: (T-8) Children's Square Table 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 2 MFN-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-301
Project #: 13.7042.430 Item Description: (T-8) Children's Rectangular Table 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 1 MFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-301
Project #: 13.7042.430 Item Description: (T-8) Children's Rectangular Table 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 2 MFN-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-302
Project #: 13.7042.430 Item Description: (T-5) End Table - Uga 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 MFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-302
Project #: 13.7042.430 Item Description: (T-5) End Table - Uga 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-302
Project #: 13.7042.430 Item Description: (T-5) End Table - Uga 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-303
Project #: 13.7042.430 Item Description: (T-6) Nesting Tables - Carisa 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Notes: Divide the three tables into a two and one set in order to place on both sides of the
sofa. The largest table is labeled MFN-303A and the two smaller tables together are
labeled MFN-303B.
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-303
Project #: 13.7042.430 Item Description: (T-6) Nesting Tables - Carisa 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-303
Project #: 13.7042.430 Item Description: (T-6) Nesting Tables - Carisa 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-303
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-304
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - E5432 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 MFN-304
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-304
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - E5432 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-304
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-304
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - E5432 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-304
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-305
Project #: 13.7042.430 Item Description: (T-5) End Table - Newton 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-305
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-305
Project #: 13.7042.430 Item Description: (T-5) End Table - Newton 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-305
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-305
Project #: 13.7042.430 Item Description: (T-5) End Table - Newton 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-305
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-306
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Factory Cart 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-306
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-306
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Factory Cart 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-306
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-306
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Factory Cart 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-306
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-307
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Dutch Industrial1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-307
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-307
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Dutch Industrial2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-307
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-307
Project #: 13.7042.430 Item Description: (T-6) Coffee Table - Dutch Industrial3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-307
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-308
Project #: 13.7042.430 Item Description: (T-5) End Table - Murano Round 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-308
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-308
Project #: 13.7042.430 Item Description: (T-5) End Table - Murano Round 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-308
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-308
Project #: 13.7042.430 Item Description: (T-5) End Table - Murano Round 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-308
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-309
Project #: 13.7042.430 Item Description: (T-5) End Table - Nora 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-309
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-309
Project #: 13.7042.430 Item Description: (T-5) End Table - Nora 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-309
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-309
Project #: 13.7042.430 Item Description: (T-5) End Table - Nora 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-309
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-310
Project #: 13.7042.430 Item Description: (D-11) Staff Desk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-11) Staff Desk
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-310
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-310
Project #: 13.7042.430 Item Description: (D-11) Staff Desk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-310
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-311
Project #: 13.7042.430 Item Description: (D-6) Auditing Desk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-6) Auditing Desk
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-311
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-311
Project #: 13.7042.430 Item Description: (D-6) Auditing Desk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-311
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-312
Project #: 13.7042.430 Item Description: (D-4) Writing Desk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-4) Writing Desk
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 MFN-312
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-312
Project #: 13.7042.430 Item Description: (D-4) Writing Desk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-312
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-313
Project #: 13.7042.430 Item Description: Reception Desk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Reception Desk
Includes Components: B-10.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-313
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-313
Project #: 13.7042.430 Item Description: Reception Desk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-313
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-314
Project #: 13.7042.430 Item Description: Reception Desk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Reception Desk
Includes Components: P-1, Cab-2.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-314
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-314
Project #: 13.7042.430 Item Description: Reception Desk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-314
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-315
Project #: 13.7042.430 Item Description: Reception Desk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Reception Desk
Includes Components: P-1, P-1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-315
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-315
Project #: 13.7042.430 Item Description: Reception Desk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-315
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-316
Project #: 13.7042.430 Item Description: (T-8) Display Table 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-8) Display Table
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 MFN-316
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-316
Project #: 13.7042.430 Item Description: (T-8) Display Table 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-316
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-317
Project #: 13.7042.430 Item Description: (T-9) Testing Table 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-9) Testing Table
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
Page 1 MFN-317
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-317
Project #: 13.7042.430 Item Description: (T-9) Testing Table 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-317
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-318
Project #: 13.7042.430 Item Description: (T-12) CD Player & Study Table 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-12) CD Player & Study Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-318
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-318
Project #: 13.7042.430 Item Description: (T-12) CD Player & Study Table 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-318
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-320
Project #: 13.7042.430 Item Description: (Cab-14) Children's Storage Cabinet 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 1 MFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-320
Project #: 13.7042.430 Item Description: (Cab-14) Children's Storage Cabinet 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 2 MFN-320
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-321
Project #: 13.7042.430 Item Description: (B-10) Children's Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 1 MFN-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-321
Project #: 13.7042.430 Item Description: (B-10) Children's Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 2 MFN-321
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-322
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-11.1, Cab-20, B-11.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-322
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-322
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-323
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-323
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-323
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-324
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-5.4, F-3.4, F-3.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-324
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-324
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-325
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4, B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-325
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-325
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-326
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.2, B-11.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-326
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-326
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-326
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-327
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-5.2, B-5.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-327
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-327
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-327
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-328
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4, B-3.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-328
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-328
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-328
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-329
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-3.4, B-3.4, B-3.4, B-3.4 (Back to Back)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-329
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-329
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-329
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-330
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: F-3.2, B-10.2, Cab-2.1, F-3.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-330
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-330
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-330
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-331
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-3.2, Cab-10, B-3.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-331
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-331
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-331
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-332
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: B-11.4, Cab-20, B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-332
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-332
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-332
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-333
Project #: 13.7042.430 Item Description: Bookcase 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Bookcase
Includes Components: B-11.4 (Qty 4)
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-333
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-333
Project #: 13.7042.430 Item Description: Bookcase 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-333
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-334
Project #: 13.7042.430 Item Description: Files 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Filing Cabinet
Includes Components: F-3.3, F-3.3
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-334
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-334
Project #: 13.7042.430 Item Description: Files 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-334
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-335
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.1, B-10.4, Cab-11.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-335
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-335
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-335
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-336
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-9.1, Cab-2.1, Cab-9.1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-336
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-336
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-336
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-337
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (D-8) Counter
Includes Components: Cab-2.1, Cab-15.3, F-3.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-337
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-337
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-337
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-338
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: F-4.4, B-11.4, B-11.4
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-338
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-338
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-338
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-339
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: Cab-15.1, F-4.2, Cab-2.2
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-339
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-339
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-339
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-340
Project #: 13.7042.430 Item Description: Combination Cabinetry 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Cabinetry
Includes Components: F-3.4, B-5.4, Cab-15.3, O-1.6, O-1.6
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-340
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-340
Project #: 13.7042.430 Item Description: Combination Cabinetry 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-340
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 MFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 4
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 4 MFN-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Fabric - JA029 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 MFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Fabric - JA029 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-400.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Fabric - JA029 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-401
Project #: 13.7042.430 Item Description: (S-2) Armchair - 373 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
Page 1 MFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-401
Project #: 13.7042.430 Item Description: (S-2) Armchair - 373 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-401
Project #: 13.7042.430 Item Description: (S-2) Armchair - 373 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-401.1
Project #: 13.7042.430 Item Description: (S-2) Graded-in - 1305 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-401.1
Project #: 13.7042.430 Item Description: (S-2) Graded-in - 1305 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-401.1
Project #: 13.7042.430 Item Description: (S-2) Graded-in - 1305 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-402
Project #: 13.7042.430 Item Description: (S-10) Children's Chair 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Required Item(s) for Designer Approval Prior to Fabrication: Prepared By: ATS
Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate
Page 1 MFN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-402
Project #: 13.7042.430 Item Description: (S-10) Children's Chair 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 2 MFN-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-403
Project #: 13.7042.430 Item Description: (S-6) Conference Chair - Goal Air with
1
Arms
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
Page 1 MFN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-403
Project #: 13.7042.430 Item Description: (S-6) Conference Chair - Goal Air with
2
Arms
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-403
Project #: 13.7042.430 Item Description: (S-6) Conference Chair - Goal Air with
3
Arms
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-403.1
Project #: 13.7042.430 Item Description: (S-6, Seat) Graded-in Fabric - JA060 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 MFN-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-403.1
Project #: 13.7042.430 Item Description: (S-6, Seat) Graded-in Fabric - JA060 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-403.1
Project #: 13.7042.430 Item Description: (S-6, Seat) Graded-in Fabric - JA060 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-404
Project #: 13.7042.430 Item Description: (S-8) Testing Chair - Mansfield 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
• All metal parts must be guaranteed against rust and corrosion.
Page 1 MFN-404
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-404
Project #: 13.7042.430 Item Description: (S-8) Testing Chair - Mansfield 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-404
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-404
Project #: 13.7042.430 Item Description: (S-8) Testing Chair - Mansfield 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-404
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-404.1
Project #: 13.7042.430 Item Description: (S-8) Graded-in - Brompton 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-404.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-404.1
Project #: 13.7042.430 Item Description: (S-8) Graded-in - Brompton 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-404.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-404.1
Project #: 13.7042.430 Item Description: (S-8) Graded-in - Brompton 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-404.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405
Project #: 13.7042.430 Item Description: (S-4) Sofa - Dansk 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 MFN-405
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405
Project #: 13.7042.430 Item Description: (S-4) Sofa - Dansk 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-405
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405
Project #: 13.7042.430 Item Description: (S-4) Sofa - Dansk 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-405
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405.1
Project #: 13.7042.430 Item Description: (S-4) COM - Badlands 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-405.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405.1
Project #: 13.7042.430 Item Description: (S-4) COM - Badlands 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-405.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405.2
Project #: 13.7042.430 Item Description: Pillow COM - Russet 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-405.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-405.2
Project #: 13.7042.430 Item Description: Pillow COM - Russet 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-405.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-406
Project #: 13.7042.430 Item Description: (S-16) Bench -Kendall 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 MFN-406
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-406
Project #: 13.7042.430 Item Description: (S-16) Bench -Kendall 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-406
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-406
Project #: 13.7042.430 Item Description: (S-16) Bench -Kendall 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-406
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-406.1
Project #: 13.7042.430 Item Description: (S-16) COM - Monarch 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-406.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-406.1
Project #: 13.7042.430 Item Description: (S-16) COM - Monarch 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-406.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-406.1
Project #: 13.7042.430 Item Description: (S-16) COM - Monarch 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-406.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-407
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Blackburn 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-407
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-407
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Blackburn 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-407
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-407
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Blackburn 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-407
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-407.1
Project #: 13.7042.430 Item Description: (S-3) COM - Paradox 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-407.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-407.1
Project #: 13.7042.430 Item Description: (S-3) COM - Paradox 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-407.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-408
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Kingston 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
Page 1 MFN-408
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-408
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Kingston 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-408
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-408
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Kingston 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-408
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-408.1
Project #: 13.7042.430 Item Description: (S-3) COM - Celica 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-408.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-408.1
Project #: 13.7042.430 Item Description: (S-3) COM - Celica 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-408.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-408.1
Project #: 13.7042.430 Item Description: (S-3) COM - Celica 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-408.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-409
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 MFN-409
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-409
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-409
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-409
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-409
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-409.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 MFN-409.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-409.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-409.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-409.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-409.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410
Project #: 13.7042.430 Item Description: (S-4) Sofa - 2145-S2 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 MFN-410
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410
Project #: 13.7042.430 Item Description: (S-4) Sofa - 2145-S2 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-410
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410
Project #: 13.7042.430 Item Description: (S-4) Sofa - 2145-S2 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-410
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410.1
Project #: 13.7042.430 Item Description: (S-4) COM - Java 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-410.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410.1
Project #: 13.7042.430 Item Description: (S-4) COM - Java 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-410.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410.1
Project #: 13.7042.430 Item Description: (S-4) COM - Java 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-410.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410.2
Project #: 13.7042.430 Item Description: (S-4) COM - Chestnut 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-410.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410.2
Project #: 13.7042.430 Item Description: (S-4) COM - Chestnut 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-410.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-410.2
Project #: 13.7042.430 Item Description: (S-4) COM - Chestnut 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-410.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-411
Project #: 13.7042.430 Item Description: (S-19) Chair - Guest Chair 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 MFN-411
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-411
Project #: 13.7042.430 Item Description: (S-19) Chair - Guest Chair 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-411
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-411
Project #: 13.7042.430 Item Description: (S-19) Chair - Guest Chair 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-411
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-411.1
Project #: 13.7042.430 Item Description: (S-19) COM - Tiger's Eye 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-411.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-411.1
Project #: 13.7042.430 Item Description: (S-19) COM - Tiger's Eye 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-411.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-412
Project #: 13.7042.430 Item Description: (S-16) Bench - Kayu 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 MFN-412
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-412
Project #: 13.7042.430 Item Description: (S-16) Bench - Kayu 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-412
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-412
Project #: 13.7042.430 Item Description: (S-16) Bench - Kayu 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-412
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-413
Project #: 13.7042.430 Item Description: (S-4) Sofa - Sumner 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
• All metal parts must be guaranteed against rust and corrosion.
Page 1 MFN-413
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-413
Project #: 13.7042.430 Item Description: (S-4) Sofa - Sumner 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-413
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-413
Project #: 13.7042.430 Item Description: (S-4) Sofa - Sumner 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-413
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-413.1
Project #: 13.7042.430 Item Description: (S-19) COM - Kernel 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-413.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-413.1
Project #: 13.7042.430 Item Description: (S-19) COM - Kernel 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-413.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-413.1
Project #: 13.7042.430 Item Description: (S-19) COM - Kernel 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-413.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-414
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Upholstered seat & back with wood base
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-414
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-414
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-414
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-414
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-414
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-414.1
Project #: 13.7042.430 Item Description: (S-19) COM - Paprika 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-414.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-414.1
Project #: 13.7042.430 Item Description: (S-19) COM - Paprika 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-414.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-414.1
Project #: 13.7042.430 Item Description: (S-19) COM - Paprika 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-414.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-415
Project #: 13.7042.430 Item Description: (S-7) Writing Desk Chair - Custom 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Low back side chair with upholstered seat and wicker back
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 MFN-415
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-415
Project #: 13.7042.430 Item Description: (S-7) Writing Desk Chair - Custom 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-415
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-415
Project #: 13.7042.430 Item Description: (S-7) Writing Desk Chair - Custom 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-415
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-415.1
Project #: 13.7042.430 Item Description: (S-7) COM - Squash 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-415.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-415.1
Project #: 13.7042.430 Item Description: (S-7) COM - Squash 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-415.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-415.1
Project #: 13.7042.430 Item Description: (S-7) COM - Squash 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-415.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
Page 1 MFN-416
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-416
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-416
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 4
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 4 MFN-416
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-416.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-416.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-416.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-416.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-417
Project #: 13.7042.430 Item Description: (S-13) PC Chair - Stratus 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 MFN-417
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-417
Project #: 13.7042.430 Item Description: (S-13) PC Chair - Stratus 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-417
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-417
Project #: 13.7042.430 Item Description: (S-13) PC Chair - Stratus 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-417
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-417.1
Project #: 13.7042.430 Item Description: (S-13) COM - Destiny 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality and must meet or exceed local codes.
Page 1 MFN-417.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-417.1
Project #: 13.7042.430 Item Description: (S-13) COM - Destiny 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-417.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-418
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Upholstered seat & back with wood base
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 MFN-418
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-418
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-418
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-418
Project #: 13.7042.430 Item Description: (S-3) Lounge Chair - Custom 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-418
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-418.1
Project #: 13.7042.430 Item Description: (S-19) COM - Kernel 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 MFN-418.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-418.1
Project #: 13.7042.430 Item Description: (S-19) COM - Kernel 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-418.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-418.1
Project #: 13.7042.430 Item Description: (S-19) COM - Kernel 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
1E+02
Page 3 MFN-418.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-600
Project #: 13.7042.430 Item Description: Table Lamp - Crystal Banister 1
Issue Date: 07/30/10 Area Name: Medium Finish Level
Instructions:
• Refer to Preamble Section 0.0 and 6.0 for additional requirements.
• Refer to attached for Photograph or Drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• Fabricator must review design concept and inform Gensler of any problems or discrepancies prior to fabrication.
• Must be U.L. approved and labeled. Manufacturer responsible for supplying UL approved documentation to the
purchasing agent.
• Metal grade and thickness must be commercial grade and withstand heavy hospitality usage.
Page 1 MFN-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-600
Project #: 13.7042.430 Item Description: Table Lamp - Crystal Banister 2
Issue Date: 07/30/10 Area Name: Medium Finish Level
Page 2 MFN-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: MFN-600
Project #: 13.7042.430 Item Description: Table Lamp - Crystal Banister 3
Issue Date: 07/30/10 Area Name: Medium Finish Level
2E+02
Page 3 MFN-600
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-300
Project #: 13.7042.430 Item Description: (T-6) Coffee Table 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
• All metal parts must be guaranteed against rust and corrosion.
Page 1 PUR-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-300
Project #: 13.7042.430 Item Description: (T-6) Coffee Table 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-300
Project #: 13.7042.430 Item Description: (T-6) Coffee Table 3
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-400
Project #: 13.7042.430 Item Description: (S-16) Bench - Teak 1
Issue Date: 07/30/10 Area Name: Purification
COM/COL:
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All metal parts must be guaranteed against rust and corrosion.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
Page 1 PUR-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-400
Project #: 13.7042.430 Item Description: (S-16) Bench - Teak 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-400
Project #: 13.7042.430 Item Description: (S-16) Bench - Teak 3
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-401
Project #: 13.7042.430 Item Description: (S-14) Stool - Barstool 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 PUR-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-401
Project #: 13.7042.430 Item Description: (S-14) Stool - Barstool 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-401
Project #: 13.7042.430 Item Description: (S-14) Stool - Barstool 3
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-402
Project #: 13.7042.430 Item Description: (S-15) Purification Chair - Algarve 1
Armchair
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All materials and construction must be of contract quality and must meet or exceed local codes.
• All cushions, foam padding and upholstered panels must be inherently flame retardant or treated to meet California
Bulletin #117 and all other local, state and federal code requirements.
Page 1 PUR-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-402
Project #: 13.7042.430 Item Description: (S-15) Purification Chair - Algarve 2
Armchair
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-402
Project #: 13.7042.430 Item Description: (S-15) Purification Chair - Algarve 3
Armchair
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-402
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
Page 1 PUR-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 3
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Goal Air 4
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 4 PUR-403
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Vinyl - SCL-0141
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 PUR-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Vinyl - SCL-0142
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-403.1
Project #: 13.7042.430 Item Description: (S-5, Seat) Graded-in Vinyl - SCL-0143
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-403.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-700
Project #: 13.7042.430 Item Description: Framed Mirror 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
• All parts must be sealed to prevent rust and corrosion.
Page 1 PUR-700
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-700
Project #: 13.7042.430 Item Description: Framed Mirror 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-700
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-700
Project #: 13.7042.430 Item Description: Framed Mirror 3
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-700
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-800
Project #: 13.7042.430 Item Description: Shower Curtain 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
• All parts must be sealed to prevent rust and corrosion.
• Must provide with a suitable sealer to prevent water leakage and discoloration.
Page 1 PUR-800
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-800
Project #: 13.7042.430 Item Description: Shower Curtain 2
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 2 PUR-800
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-900
Project #: 13.7042.430 Item Description: Treadmill 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 PUR-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-900
Project #: 13.7042.430 Item Description: Treadmill 2
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 2 PUR-900
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-901
Project #: 13.7042.430 Item Description: (CAB-4) Lockers 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble for additional requirements.
• Refer to attached photograph or drawing.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings/manufacturers data sheet must be submitted to Gensler for approval prior to fabrication. Submit
manufacturer's warranty to Purchasing Agent.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
intent and reference only.
• All materials and construction must be of contract quality.
Page 1 PUR-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-901
Project #: 13.7042.430 Item Description: (CAB-4) Lockers 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-901
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-902
Project #: 13.7042.430 Item Description: Sauna 1
Issue Date: 07/30/10 Area Name: Purification
Instructions:
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Refer to Preamble Section 0.0 and 9.0 for additional requirements.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 PUR-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-902
Project #: 13.7042.430 Item Description: Sauna 2
Issue Date: 07/30/10 Area Name: Purification
Page 2 PUR-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: PUR-902
Project #: 13.7042.430 Item Description: Sauna 3
Issue Date: 07/30/10 Area Name: Purification
1E+02
Page 3 PUR-902
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-300
Project #: 13.7042.430 Item Description: Secondary Reception Desk 1
Issue Date: 07/30/10 Area Name: Qualification Library
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom Secondary Reception Desk
Includes Components: P-1
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 QLS-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-300
Project #: 13.7042.430 Item Description: Secondary Reception Desk 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-301
Project #: 13.7042.430 Item Description: (T-1) Course Room Table 1
Issue Date: 07/30/10 Area Name: Qualification Library
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-1) Course Room Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 QLS-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-301
Project #: 13.7042.430 Item Description: (T-1) Course Room Table 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-301
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-302
Project #: 13.7042.430 Item Description: (T-12) CD Player & Study Table 1
Issue Date: 07/30/10 Area Name: Qualification Library
Phone: Phone:
Fax: Fax:
Contact: Contact:
E-mail: E-mail:
Web: Web:
Description: Custom (T-12) CD Player & Study Table
Logo mounted to panel by others and supplied by owner
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Where applicable, manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and
fabrication of total quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings or prototype must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 QLS-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-302
Project #: 13.7042.430 Item Description: (T-12) CD Player & Study Table 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-302
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 1
Issue Date: 07/30/10 Area Name: Qualification Library
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
Page 1 QLS-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-400
Project #: 13.7042.430 Item Description: (S-5) Task Chair - Ataros II 3
Issue Date: 07/30/10 Area Name: Qualification Library
1E+02
Page 3 QLS-400
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-400.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 1
Issue Date: 07/30/10 Area Name: Qualification Library
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
Page 1 QLS-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-400.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-400.1
Project #: 13.7042.430 Item Description: (S-5) Graded-In Leather - LP05 3
Issue Date: 07/30/10 Area Name: Qualification Library
1E+02
Page 3 QLS-400.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 1
Issue Date: 07/30/10 Area Name: Qualification Library
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
Page 1 QLS-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 3
Issue Date: 07/30/10 Area Name: Qualification Library
1E+02
Page 3 QLS-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401
Project #: 13.7042.430 Item Description: (S-10) Course Room Chair - Mitos 4
Issue Date: 07/30/10 Area Name: Qualification Library
1E+02
Page 4 QLS-401
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 1
Issue Date: 07/30/10 Area Name: Qualification Library
Instructions:
• Refer to Preamble Section 0.0 and 4.0 for additional requirements.
• Refer to attached photograph of fabric
• Quantities listed do not include any overage or attic stock. All yardage requirements must be field verified and
confirmed by manufacturer with the PA prior to ordering. Client and/or the Purchasing Agent are solely responsible for
all quantities.
• Dye-lot must be the same for entire job.
• Fabric must be inherently flame retardant or treated to meet California Bulletin #117 and all other local, state and
federal code requirements.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
Page 1 QLS-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 2
Issue Date: 07/30/10 Area Name: Qualification Library
Page 2 QLS-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: QLS-401.1
Project #: 13.7042.430 Item Description: (S-10, Seat) COM - Squash 3
Issue Date: 07/30/10 Area Name: Qualification Library
1E+02
Page 3 QLS-401.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-700
Project #: 13.7042.430 Item Description: Framed Mirror 1
Issue Date: 07/30/10 Area Name: Restrooms
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
• All parts must be sealed to prevent rust and corrosion.
Page 1 RST-700
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-700
Project #: 13.7042.430 Item Description: Framed Mirror 2
Issue Date: 07/30/10 Area Name: Restrooms
Page 2 RST-700
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-700
Project #: 13.7042.430 Item Description: Framed Mirror 3
Issue Date: 07/30/10 Area Name: Restrooms
1E+02
Page 3 RST-700
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-701
Project #: 13.7042.430 Item Description: Framed Mirror 1
Issue Date: 07/30/10 Area Name: Restrooms
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
• All parts must be sealed to prevent rust and corrosion.
Page 1 RST-701
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-701
Project #: 13.7042.430 Item Description: Framed Mirror 2
Issue Date: 07/30/10 Area Name: Restrooms
Page 2 RST-701
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-701
Project #: 13.7042.430 Item Description: Framed Mirror 3
Issue Date: 07/30/10 Area Name: Restrooms
1E+02
Page 3 RST-701
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-800
Project #: 13.7042.430 Item Description: Shower Curtain 1
Issue Date: 07/30/10 Area Name: Restrooms
Instructions:
• Refer to Preamble Section 0.0 and 8.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All materials and construction must be of contract quality.
• All parts must be sealed to prevent rust and corrosion.
• Must provide with a suitable sealer to prevent water leakage and discoloration.
Page 1 RST-800
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: RST-800
Project #: 13.7042.430 Item Description: Shower Curtain 2
Issue Date: 07/30/10 Area Name: Restrooms
1E+02
Page 2 RST-800
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: SYS-300
Project #: 13.7042.430 Item Description: Systems Furniture 1
Issue Date: 07/30/10 Area Name: Systems
Page 1 SYS-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: SYS-300
Project #: 13.7042.430 Item Description: Systems Furniture 2
Issue Date: 07/30/10 Area Name: Systems
Instructions:
• Refer to Preamble Section 0.0 and 3.0 for additional requirements.
• Refer to attached photograph or drawing.
• Manufactuer to submit sample of C.O.M. for designer's written approval prior to purchasing and fabrication of total
quantity.
• All finish samples must be submitted to Gensler for approval prior to fabrication.
• Shop drawings, prototype, or photograph must be submitted to Gensler for approval prior to fabrication.
• Quantities listed do not include any overage or attic stock. Purchasing agent shall verify quantities prior to purchasing.
Client and/or the Purchasing Agent are solely responsible for all quantities.
• Manufacturer to notify Designer of any error or conflict in specification as indicated.
• All images, photographs, renderings of specified items contained in this specification package are for general design
intent and reference only.
• All materials and construction must be of contract quality.
• All wood must comply with AWI "Custom Grade" or better quality standards. Wood construction is to be selected,
seasoned, free of knots, free of worms and vermin, and kiln-dried to a moisture content not to exceed 7%.
• Provide all drawers with ball bearing side glides and front/back stops. Interiors to be sanded and sealed.
• Provide 2" recessed back panel to accommodate electrical cable and cord access.
• Metal frame must be hand-forged wrought iron with hand-welded joints. All joints must be clean, no excess solder to
remain.
• All moving hardware must be smooth operating, heavy duty (Accuride or equal).
• All metal parts must be guaranteed against rust and corrosion.
• Fabricator must provide a structurally sound product with proper proportions to insure stability and prevent tipping.
Earthquake prone areas need to be bolted.
• Heavy-duty nylon furniture glides; diameter to be sized according to item's leg dimensions without being visable. Glide
color to best match leg finish.
• Interior hardware to be non-corrosive.
• Manufacturer to coordinate all details and equipment dimensions to ensure a proper fit prior to production.
• Manufacturer to provide all required hardware and instructions for proper installation.
• Manufacturer to provide with heavy-duty cleats for wall hung security mount to wall.
• Provide venting hole at rear of cabinet for adequate air circulation around TV and/or other equipment.
• If imported, fumigation may be required depending on country of origin and certificate.
Page 2 SYS-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: SYS-300
Project #: 13.7042.430 Item Description: Systems Furniture 3
Issue Date: 07/30/10 Area Name: Systems
1E+02
Page 3 SYS-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: SYS-300
Project #: 13.7042.430 Item Description: Systems Furniture 4
Issue Date: 07/30/10 Area Name: Systems
1E+02
Page 4 SYS-300
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.1
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-500.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.1
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-500.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.1
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-500.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.2
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-500.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.2
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-500.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.2
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-500.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.3
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-500.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.3
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-500.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.3
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-500.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.4
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-500.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.4
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-500.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-500.4
Project #: 13.7042.430 Item Description: Dual Roller and Blackout Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-500.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-501
Project #: 13.7042.430 Item Description: Single Blackout Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-501
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-501
Project #: 13.7042.430 Item Description: Single Blackout Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-501
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-501
Project #: 13.7042.430 Item Description: Single Blackout Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-501
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.1
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.1
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.1
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.1
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.2
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.2
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.2
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.2
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.3
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.3
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.3
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.3
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.4
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.4
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.4
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.4
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.5
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.5
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.5
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.5
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.5
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.5
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.6
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.6
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.6
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.6
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.6
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.6
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.7
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.7
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.7
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.7
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.7
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.7
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.8
Project #: 13.7042.430 Item Description: Single Roller Shade 1
Issue Date: 07/30/10 Area Name: Window Treatments
Page 1 WTR-502.8
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.8
Project #: 13.7042.430 Item Description: Single Roller Shade 2
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 2 WTR-502.8
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: WTR-502.8
Project #: 13.7042.430 Item Description: Single Roller Shade 3
Issue Date: 07/30/10 Area Name: Window Treatments
1E+02
Page 3 WTR-502.8
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-01
Project #: 13.7042.430 Item Description: Broadloom Carpet 1
Issue Date: 07/30/10
Page 1 C-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-01
Project #: 13.7042.430 Item Description: Broadloom Carpet 2
Issue Date: 07/30/10
1E+02
Page 2 C-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-02
Project #: 13.7042.430 Item Description: Broadloom Carpet 1
Issue Date: 07/30/10
Page 1 C-02
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-02
Project #: 13.7042.430 Item Description: Broadloom Carpet 2
Issue Date: 07/30/10
1E+02
Page 2 C-02
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-03
Project #: 13.7042.430 Item Description: Broadloom Carpet 1
Issue Date: 07/30/10
Page 1 C-03
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-03
Project #: 13.7042.430 Item Description: Broadloom Carpet 2
Issue Date: 07/30/10
1E+02
Page 2 C-03
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-04
Project #: 13.7042.430 Item Description: Broadloom Carpet 1
Issue Date: 07/30/10
Page 1 C-04
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-04
Project #: 13.7042.430 Item Description: Broadloom Carpet 2
Issue Date: 07/30/10
1E+02
Page 2 C-04
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-05
Project #: 13.7042.430 Item Description: Broadloom Carpet 1
Issue Date: 07/30/10
Page 1 C-05
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: C-05
Project #: 13.7042.430 Item Description: Broadloom Carpet 2
Issue Date: 07/30/10
1E+02
Page 2 C-05
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPT-01
Project #: 13.7042.430 Item Description: Carpet Tile 1
Issue Date: 07/30/10
Instructions:
• Refer to Preamble Section 0.0 and 1.0 for additional requirements.
• Refer to attached photograph or drawing.
• Quantities listed do not include any overage or attic stock. All quantities and widths must be field verified and
confirmed by carpet installer with the Purchasing Agent prior to ordering. Client and/or the P.A. are solely responsible
for all quantities.
• Manufacturer to provide seaming diagram for installation. All quanities must be verified and confirmed with Purchasing
Agent and Carpet Installer prior to manufacturing.
• Installer to verify appropriate seaming and pattern matching with manufacturer and designer.
Page 1 CPT-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPT-01
Project #: 13.7042.430 Item Description: Carpet Tile 2
Issue Date: 07/30/10
Page 2 CPT-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: CPT-01
Project #: 13.7042.430 Item Description: Carpet Tile 3
Issue Date: 07/30/10
1E+02
Page 3 CPT-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FPW-01
Project #: 13.7042.430 Item Description: Fabric Wrapped Panel 1
Issue Date: 07/30/10
Page 1 FPW-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FPW-01
Project #: 13.7042.430 Item Description: Fabric Wrapped Panel 2
Issue Date: 07/30/10
1E+02
Page 2 FPW-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FPW-02
Project #: 13.7042.430 Item Description: Fabric Wrapped Panel 1
Issue Date: 07/30/10
Page 1 FPW-02
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FPW-02
Project #: 13.7042.430 Item Description: Fabric Wrapped Panel 2
Issue Date: 07/30/10
1E+02
Page 2 FPW-02
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FPW-03
Project #: 13.7042.430 Item Description: Fabric Wrapped Panel 1
Issue Date: 07/30/10
Page 1 FPW-03
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: FPW-03
Project #: 13.7042.430 Item Description: Fabric Wrapped Panel 2
Issue Date: 07/30/10
1E+02
Page 2 FPW-03
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDW-01
Project #: 13.7042.430 Item Description: Hardware 1
Issue Date: 07/30/10
Page 1 HDW-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDW-01
Project #: 13.7042.430 Item Description: Hardware 2
Issue Date: 07/30/10
1E+02
Page 2 HDW-01
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDW-02
Project #: 13.7042.430 Item Description: Hardware 1
Issue Date: 07/30/10
Page 1 HDW-02
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Project Name: CSI Org - Tampa Item Number: HDW-02
Project #: 13.7042.430 Item Description: Hardware 2
Issue Date: 07/30/10
1E+02
Page 2 HDW-02
Gensler 101 Marietta Street NW Suite 3000 Atlanta, GA 30303 Southeast, USA
p 404.507.1000 f 404.507.1001 www.gensler.com
Furniture Number CRM-300 / MFN-310 Gensler
Project Project Number
STAFF DESK
Drawing Scale Date
AS NOTED 07.30.10
X ITEM NUMBER X
SS1
CRM-300.1 60"
1 1/2" COUNTER
TOP CRM-300.2 48"
ITEM NUMBER X
30"
B MFN-310.1 60"
MFN-310.2 48"
PEDESTAL
PROVIDED BY
FURNITURE VENDOR A
1 PLAN
1/2"=1'-0"
SS1
1 1/2" COUNTER TOP
SS1
WD2 1 1/2" COUNTER TOP
3/8" REVEAL, TYP
WD2
3/8" REVEAL, TYP
PEDESTAL
28 1/2"
28 1/2"
WD1
WD1 END PANEL
END PANEL
A ELEVATION B ELEVATION
1/2" = 1'-0" 1/2" = 1'-0"
36"
2" TYP
28 1/2" TYP
SS1
15"
1 1/2"
SURFACE TOP
WD-02, TYP
RETURN A - (OPEN)
WD2
3/8" REVEAL, TYP
2" 18"
36"
SS1
1/2" COUNTER TOP
WD2
SS1
28 1/2"
15"
WD1
BASE, FRAME &
RETURN B - (BOOKCASE, LEFT) TOEKICK
36"
WD2
SS1 3/8" REVEAL, TYP
15"
B-10.1
1 1/2" SURFACE SS1
TOP
1/2" COUNTER TOP
WD2
28 1/2"
WD1
18" 2" BASE, FRAME &
TOEKICK
X
ITEM NUMBER X
CRM-301.1 30"
CRM-301.2 60"
SUPPORT BELOW
CRM-301.3 90"
PANEL BELOW
A
36"
SS1
4" MAX
1 1/2" COUNTER
TOP
1 PLAN
1/2" = 1'-0"
SUPPORT
SS1 SS1
1 1/2" COUNTER TOP 1 1/2"
COUNTER TOP
WD2 WD2
3/8" REVEAL, TYP 3/8" REVEAL, TYP
28 1/2"
SIGNAGE, PROVIDE
28 1/2"
BY OWNER WD1
END PANEL
A ELEVATION B ELEVATION
1/2" = 1'-0" 1/2" = 1'-0"
ITEM NUMBER X
CRM-302.1 30"
2"
9" TYP
SS1
1 1/2" COUNTER TOP
EQ
CRM-901
EQ
SUPPORT BELOW
CLEAR RUBBER BUMPERS BETWEEN
EQ
GLASS
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" COUNTER TOP
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
A ELEVATION
1/2" = 1'-0"
SUPPORT
SS1
1 1/2"
COUNTER TOP
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
B ELEVATION
1/2" = 1'-0"
ITEM NUMBER X
CRM-302.B.1 30"
CRM-302.B.2 60"
CRM-302.B.3 90"
CL
EQ SPECIFICATION CRM-900
SS1
1 1/2" COUNTER TOP
EQ
CRM-901
EQ
SUPPORT BELOW
EQ
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" COUNTER TOP
WD2
3/8" REVEAL, TYP
36"
WD1
END PANEL
A ELEVATION
1/2" = 1'-0"
SUPPORT
SS1
1 1/2"
COUNTER TOP
WD2
3/8" REVEAL, TYP
36"
WD1
END PANEL
B ELEVATION
1/2" = 1'-0"
ITEM NUMBER X
CRM-303.1 30"
CRM-303.2 60"
CRM-303.3 90"
A
48"
WD2
CD PLAYER HOUSING WITH
REMOVABLE 3/4" TOP; TO HOLD
CD PLAYERS ON EACH SIDE
1/8" REVEAL
X
B
SUPPORT BELOW
SS1
1 1/2" COUNTER TOP
PANEL BELOW
1 PLAN
1/2" = 1'-0"
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
A ELEVATION
1/2" = 1'-0"
WD2
3/4" CD SHELF AS
SCHEDULED
SS1
EQ EQ
1 1/2"
COUNTER TOP
5"
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
PLUG STRIP
SUPPORT
B ELEVATION
1/2" = 1'-0"
30"
SS1
1 1/2" COUNTER TOP
30"
MT1
1 1/2" BLACKENED
STEEL LEGS &
SUPPORT BELOW
1 PLAN
1/2" = 1'-0"
SS1
MT1
1 1/2" BLACKENED
STEEL
A ELEVATION
1/2" = 1'-0"
18"
SS1
24"
MT1
1 1/2" BLACKENED
STEEL LEGS &
SUPPORT BELOW
A
1 PLAN
1/2" = 1'-0"
SS1
MT1
1 1/2" BLACKENED
STEEL
A ELEVATION
1/2" = 1'-0"
ITEM NUMBER X
CRM-306.1 30"
CRM-306.2 60"
CRM-306.3 90"
48"
SS1
1 1/2" COUNTER
TOP
B
X
SUPPORT BELOW
PANEL BELOW
1 PLAN
1/2"-1'-0"
SS1
1 1/2" COUNTER TOP
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
A ELEVATION
1/2" = 1'-0"
SUPPORT
SS1
1 1/2"
COUNTER TOP
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
B ELEVATION
1/2" = 1'-0"
19" SS1
22" WD2
WD2 3/8" REVEAL
8
3/8" REVEAL WD2
ADJUSTABLE SHELF W/ SOLID WOOD LIP.
ADJUSTABLE
1 1/2"
COUNTER W/ OVERHEAD
Drawing Scale Date
AS NOTED 07.30.10
180"
LINE OF OVERHEAD
ABOVE
12"
30"
B
F-3.4 CAB-5.1 CAB-7
SS1
1 1/2" COUNTER TOP LINE OF LEGS
BELOW
1 PLAN A
WD1
3/8" = 1'-0" INTERMEDIATE SUPPORT
LEG AS REQUIRED
WD2
SHELVES, TOP, 1/2" SURROUNDS,
EXPOSED INSIDE FACES, SIDE &
BACK PANEL
7
SIM
31"
13" CLR
TYP
WD1 SS1
END PANEL, SURROUNDS 1 1/2" COUNTER 1 1/2" MAX.
& EXPOSED INSIDE FACES 8
TOP
60"
28 1/2"
7
SIM
3/8" REVEAL
4" 7 WD2
WD1
DOOR, SHELVES &
DRAWERS FRONT INTERMEDIATE
SUPPORT LEG
WD2 AS REQUIRED
A ELEVATION BASE & TOEKICK
3/8" = 1'-0"
COUNTER W/ OVERHEAD
Drawing Scale Date
AS NOTED 07.30.10
SS1 18"
1 1/2" COUNTER TOP
1"
1 1/2"
3/8" REVEAL
12
28 1/2"
0°
WD1
WD1
END PANEL INTERMEDIATE
SUPPORT LEG
WD2 AS REQUIRED
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
184"
18"
F-4.4 CAB-15.6
B-11.4 B-11.4 B-11.4
1 PLAN WD2
CRM-320
1/2" = 1'-0" DOORS &
DRAWERS FRONT
SS1
1 1/2" TOP
3/8" REVEAL
8
36"
SIM
7 WD1
EXPOSED INSIDE
FACES, SIDE PANELS &
A ELEVATION SURROUND
1/2" = 1'-0" WD2
BASE, TOE KICK &
SHELVES
3/8" REVEAL
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
40"
12"
B-11.4
CRM-321
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
36"
7
WD2
A ELEVATION TOE KICK, BASE &
1/2" = 1'-0" SHELVES
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
58"
15"
CAB-15.6 CAB-5.2
CRM-322
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
8
3/8" REVEAL
WD1
36"
7 WD2
BASE, TOE KICK, SHELVES
& DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
94"
18"
F-4.3 CAB-15.5
B-11.3
CRM-323
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
EXPOSED INSIDE
36"
7 WD2
BASE, TOE KICK
SHELVES, DOOR &
DRAWER FRONTS
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
112"
12"
1 PLAN CRM-324
1/2" = 1'-0"
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
EXPOSED INSIDE
36"
WD2
7
BASE, TOE KICK
& SHELVES
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
184"
15"
1 PLAN CRM-325
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
36"
7
SIM
WD1
7
EXPOSED INSIDE FACES,
SIDE PANELS & SURROUND
A ELEVATION WD2
1/2" = 1'-0" BASE, TOE KICK, SHELVES
& DOOR FRONTS
BOOKCASE
Drawing Scale Date
AS NOTED 07.30.10
34"
12"
B-11.3
CRM-326
1 PLAN
1/2" = 1'-0"
WD1
34 1/4"
EXPOSED INSIDE
7 FACES, SIDE PANELS
& SURROUND
SIM 3/8" REVEAL
WD2
7
A ELEVATION BASE TOE KICK & SHELVES
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
12" 52"
B-11.2 B-11.2
CRM-327
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
EXPOSED INSIDE
FACES, SIDE PANELS &
SURROUND
36"
7
3/8" REVEAL
SIM
7 WD2
BASE, TOE KICK &
SHELVES
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
64"
15"
CAB-15.5 B-11.3
A
1 PLAN
1/2" = 1'-0" CRM-328
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
EXPOSED INSIDE
36"
WD2
7 BASE, TOE KICK
SHELVES & DOOR
FRONTS
A ELEVATION
1/2" = 1'-0"
PARTITION
Drawing Scale Date
AS NOTED 07.30.10
6" 48" 6"
WD1
SOLID WOOD FRAME
12"
A
PP1
1 PLAN
CRM-329
1/2" = 1'-0"
4"
4"
1/8" REVEAL
PP1
72"
1/8" REVEAL
WD1
SOLID WOOD FRAME
33"
CONCEALED
1/2"
SUPPORT RODS
EQ EQ EQ EQ
STEEL BASE POWDER
CL CL CL COATED BLACK MATTE
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
202"
18"
1 PLAN
CRM-330
3/8" = 1'-0"
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
36"
7 EXPOSED INSIDE
FACES, SIDE PANELS
SIM & SURROUND
3/8" REVEAL
7 WD2 WD2
SHELVES & DRAWER BASE, TOE KICK &
FRONTS DOOR FRONTS
A ELEVATION
3/8" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
76"
12"
B-11.4 B-11.4
A
1 PLAN
1/2" = 1'-0" CRM-331
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
EXPOSED INSIDE FACES,
SIDE PANELS &
36"
7 SURROUND
3/8" REVEAL
SIM
WD2
7
BASE, TOE KICK &
SHELVES
A ELEVATION
1/2" = 1'-0"
CABINET
Drawing Scale Date
AS NOTED 07.30.10
34"
15"
CAB-12
CRM-332
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
EXPOSED INSIDE
28 1/2"
FACES, SURROUNDS
7 & SIDE PANELS
3/8" REVEAL
SIM
WD2
7
BASE, TOE KICK
& DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
64"
12"
B-11.3 B-11.3
1 PLAN
CRM-333
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
EXPOSED INSIDE
36"
WD2
A ELEVATION
1/2" = 1'-0"
FILE CABINET
Drawing Scale Date
AS NOTED 07.30.10
34"
18"
F-4.3
1 PLAN CRM-334
1/2" = 1'-0"
WD1
EXPOSED INSIDE
FACES, SIDE PANELS
& SURROUND
34 1/4"
7 WD2
BASE, TOE KICK &
2 ELEVATION DRAWER FRONTS
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
34"
15"
CAB-15.5
CRM-335
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
8
3/8" REVEAL
WD1
EXPOSED INSIDE
36"
7 WD2
BASE, TOE KICK
& DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
166"
18"
CAB-5.2 CAB-9.2
B-11.4 B-11.4 CAB-7.2
1 PLAN CRM-336
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
36"
SIM
7 WD1
EXPOSED INSIDE
FACES, SIDE PANELS
A ELEVATION & SURROUND
1/2" = 1'-0"
WD2
BASE, TOE KICK
SHELVES & DOOR
FRONTS
3/8" REVEAL
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
70"
15"
CRM-337
1 PLAN
3/8" = 1'-0"
SS1
1 1/2" TOP
8
3/8" REVEAL
7
WD1
SIM
36"
7 WD2
BASE, TOE KICK & SHELVES
A ELEVATION
3/8" = 1'-0"
36"
36"
T-6
A DV6-303
1 PLAN
DV6-303
1/2" = 1'-0"
WD1
TOP
4"
WD1
LEGS
28 1/2"
4"
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
220"
12"
1 PLAN
3/8" = 1'-0" WD2
TOP, BASE, SHELF
6 & TOE KICK
44"
SIM
7 WD1
A ELEVATION SIDE, EXPOSED
INSIDE FACES,
3/8" = 1'-0" BACKPANEL & 1/2"
SURROUNDS
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
44"
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
40"
12"
B-3.4 B DV6-321
DV6-321
1 PLAN
1/2" = 1'-0"
6 WD2
TOP, BOTTOM
SHELVES & TOE KICK
7
WD1
50"
7
A ELEVATION
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
50"
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
DV6-321
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number DV6-322 Gensler
Project Project Number
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
148"
12"
1 PLAN WD2
DV6-322
1/2" = 1'-0" TOP, BOTTOM
SHELF & TOE KICK
6
7
44"
SIM
7
WD1
A ELEVATION SIDE, 1/2" SURROUNDS,
EXPOSED INSIDE FACES
1/2" = 1'-0" & BACK PANEL
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
44"
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
DV6-322
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number DV6-323 Gensler
Project Project Number
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
DV6-323 OPP.
A 40"
B-11.4
24"
B DV6-323
B-11.4
A
1 PLAN
1/2" = 1'-0"
DV6-323
WD2
TOP, BOTTOM
SHELF & TOE KICK
36"
SIM WD1
1/2" SURROUNDS SIDE,
EXPOSED INSIDE FACES
& BACK PANEL
7
A ELEVATION
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
BENCH
Drawing Scale Date
AS NOTED 07.30.10
54"
3" 1/8"
1 1/2"
RECESSED CUSHIONS
EXTEND 1 1/2" ABOVE
18"
WOOD SURROUND
WD2
A ON ALL EXPOSED HARD
SURFACE
DV6-402
1 PLAN
1/2" = 1'-0"
RECESSED CUSHIONS
EXTEND 1 1/2" ABOVE
1 1/2"
WOOD SURROUND
3"
1/8" REVEAL
17 1/2"
WD2
ON ALL EXPOSED HARD
SURFACE
A ELEVATION
1/2" = 1'-0"
HFN-301.2
B
WD1
2" X2" BOX JOINT
30"
HFN-301.2 C WD2
C HFN-301.2
2" WORKING
COUNTER TOP OPP.
1' - 0"
ST1
6"
2" TRANSACTION
14" 62" 14" COUNTER
1 PLAN
HFN-301.1
1/2" = 1'-0"
ST1
4 2" TRANSACTION
COUNTER
WD2
2" WORKING
COUNTER TOP
43 1/2"
WD4
WD4 EXTENT AT
.
28 1/2"
TRANSACTION
OPEN OPEN 2" WOOD PIECES ELEMENT
WD4
SIDE PANEL
4"
3 1/8" REVEAL
A ELEVATION
1/2" = 1'-0"
OPEN WD2
2" WORKING
COUNTER TOP
43 1/2"
28 1/2"
WD1
OPEN SIDE PANELS
1/8" REVEAL
4"
B ELEVATION
1/2" = 1'-0"
ST1
2" TRANSACTION
COUNTER
WD2
2" WORKING
COUNTER TOP WD4
43 1/2"
WD4 ELEMENT
2" WOOD PIECES
1/8" REVEAL
4"
WD1
SIDE PANELS
C ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
66"
18"
HFN-302
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
7
SIDE PANELS, EXPOSED INSIDE
28 1/2"
WD2 WD2
7
SHELVES & DRAWER BASE, TOE KICK &
FRONTS DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
24"
F-3.1
48"
CAB-2.1 C HFN-303.2
HFN-303.3 A
B
SS2
2" WORKING
COUNTER TOP
P-1
30"
RECESSED
FRONT PANEL
12"
ST1
6"
WD4
WD1
43 1/2"
EXTENT AT
TRANSCTION
.
SIDE PANELS
ELEMENT
28 1/2"
WD2
INSET PANEL
4"
3/8" REVEAL
A ELEVATION WD4
1/2" = 1'-0" 2" WOOD PIECES
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
ST1
2" TRANSACTION COUNTER
1/8" REVEAL
WD4
BEYOND
SS2
OPEN
2" WORKING COUNTER TOP
3/8" REVEAL
43 1/2"
28 1/2"
OPEN
WD1
SIDE PANELS
4"
WD2
BACK PANEL
B ELEVATION
1/2" = 1'-0"
ST1
2" TRANSACTION COUNTER
1/8" REVEAL
3/8" REVEAL
SS2
2" WORKING COUNTER TOP
WD4
43 1/2"
EXTENT AT
.
WD1
TRANSCTION
ELEMENT OPEN SIDE PANELS, EXPOSED INSIDE
FACES & 1/2" SURROUND
4"
WD2
4" FRONT BOTTOM, SHELVES &
PANEL BEYOND DRAWER FRONTS
C ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
ST1
2" TRANSCTION COUNTER
1/8" REVEAL
SS2
2" WORKING
COUNTER TOP
3/8" REVEAL
WD4
EXTENT AT
43 1/2"
TRANSCTION
3'
WD1 ELEMENT
SIDE PANEL
4"
4" FRONT
A ELEVATION PANEL BEYOND
1/2" = 1'-0"
TROPHY CASE
Drawing Scale Date
AS NOTED 07.30.10
18" 63"
1 PLAN HFN-320
1/2" = 1'-0"
2" TYP WD2
TOP, 3/8" REVEAL
EQ EQ
WD1
TOP PANEL, 1/2"
SURROUNDS, EXPOSED
INSIDE FACES & BACK PANEL
7 GL1
SIM CLEAR TEMPERED GLASS
GL1
90"
WD2
1 1/2" FRAME, INTERMEDIATE
32"
WD2
4"
7
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
52"
12"
B-3.2 B-3.2 B HFN-321
1 PLAN
1/2" = 1'-0" HFN-321
WD2
WD1
1/2" SURROUNDS, EXPOSED
INSIDE FACES, SIDE & BACK
PANELS
5
A ELEVATION
1/2" = 1'-0" WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
50"
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
112" WD1
FINISHED BACK
12"
A
1 PLAN
1/2" = 1'-0" HFN-322
WD2
TOP, BASE,
SHELVES & TOE
KICK
50"
7 WD1
1/2" SURROUNDS,
SIM EXPOSED INSIDE
FACES, SIDE & BACK
PANELS
A ELEVATION 7
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
50"
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
40"
12"
B-4.4 B HFN-323
HFN-323
1 PLAN
1/2" = 1'-0"
6 WD2
2X2 BOX JOINTS
WD2
WD1
1/2" SURROUNDS,
EXPOSED INSIDE
72"
72"
WD2
BOTTOM
7
A ELEVATION B ELEVATION
1/2" = 1'-0" 1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
HFN-324 OPP.
A 76"
B-3.4 B-3.4
24"
2 HFN-324
B-3.4 B-3.4
A
1 PLAN
1/2" = 1'-0" HFN-324
6
WD2
SIM
WD1
1/2" SURROUNDS,
EXPOSED INSIDE FACES,
SIDE & BACK PANELS
7
A ELEVATION
1/2" = 1'-0" WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
50"
WD2
WD2
2 ELEVATION BOTTOM
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
HFN-324
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number HFN-325 Gensler
Project Project Number
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
76"
12"
B-3.4 B-3.4 B HFN-325
A
1 PLAN
1/2" = 1'-0" HFN-325
6
WD2
WD1
7
1/2" SURROUNDS,
EXPOSED INSIDE FACES,
SIM SIDE & BACK PANELS
7
A ELEVATION
1/2" = 1'-0" WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
50"
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
HFN-325
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number HGC-301 Gensler
Project Project Number
60"
PRINTER CABINET
BELOW
30"
B
CAB-2.1 CAB-15
SS1
A 1 1/2" COUNTER TOP
1 PLAN
1/2"=1'-0"
SS1 SS1
WD2
3/8" REVEAL
4"
3/8" REVEAL
2"
WD2
DOOR &
DRAWERS FRONT
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
120"
WD1
18"
HGC-320
1 PLAN
1/2" = 1'-0"
D
ST1
TYP 4
9 1 1/2" TOP
1/8" REVEAL
WD1
28 1/2"
DOORS, FRAME
& SIDE PANELS
MT1
BLACKENED
5 STEEL LEG
3/8" RECESSED
PANEL
1 1/2" DOOR
TRIM
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
111"
B HGC-321
18"
1 PLAN HGC-321
1/2" = 1'-0"
WD2
TOP & SHELF
CLR.
13"
28 1/2"
WD1
SIDE PANELS
WD2
2" TYP
3/8" LEG BASE
A ELEVATION
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
CABINET
Drawing Scale Date
AS NOTED 07.30.10
18" ; 4 EQ
WD1
1 1/2" SURROUND
18" ; 4 EQ
CAB-3
WD2
LFN-320
1 PLAN
1/2" = 1'-0"
WD1
SIDE PANEL
24 1/2"
3/8" REVEAL
WD2
BOTTOM
2 ELEVATION
1/2" = 1'-0"
CREDENZA
Drawing Scale Date
AS NOTED 07.30.10
72"
30"
B LRH-300
A
WD2
LRH-300
1 PLAN
1/2" = 1'-0"
2" TYP
WD1
SIDE PANELS
28 1/2"
WD1
BASE
A ELEVATION
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
28 1/2"
1/8" REVEAL
WD1
BASE
B ELEVATION
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
LRH-300
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number LRH-320 Gensler
Project Project Number
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
40"
12"
B-11.4 B LRH-320
LRH-320
1 PLAN
1/2" = 1'-0"
6
WD2
TOP, BASE, SHELVES
& TOE KICK
7
SIM
36"
WD1
1/2" SURROUND,
EXPOSED INSIDE FACES,
SIDE & BACK PANELS
A ELEVATION
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
36"
SIDE PANEL
WD2
WD2
BOTTOM
B ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
18" 40"
15"
1' - 0"
CAB-15.6
LRH-321
1 PLAN
1/2" = 1'-0"
WD2
2" 1" TOP
TYP SIGNAGE, PROVIDED BY OWNER
WD2
3/8" REVEAL
13" MIN
7
CLR
WD1
SIM TOP PANEL, 1/2" SURROUND
SIDE, EXPOSED INSIDE FACES
3 EQ
WD2
2"
SHELVES, INTERMEDIATE
2"
WD2
3/8" REVEAL
WD2
A ELEVATION
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
LRH-321
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number LRH-322 Gensler
Project Project Number
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
100"
18"
1 LRH-322 LRH-322
1/2" = 1'-0"
SS1
1 1/2" TOP
8 3/8" REVEAL
WD1
SIDE PANELS, EXPOSED INSIDE
7
36"
WD2
7
BASE, SHELVES &
DOOR FRONTS
2 LRH-322
1/2" = 1'-0"
WRITING DESK
Drawing Scale Date
AS NOTED 07.30.10
48"
B
30"
SS1
A 1 1/2" COUNTER TOP
1 PLAN
1/2"=1'-0"
SS1 SS1
1 1/2" COUNTER TOP 1 1/2" COUNTER TOP
1 1/2"
3/8" REVEAL
28 1/2"
28 1/2"
WD2 WD2
4"
1/8" REVEAL
A ELEVATION B ELEVATION
1/2" = 1'-0" 1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
24"
CAB-2.1
A MFN-313.3
MFN-313.2 C
48"
B-10.1
B
SS2
2" WORKING
COUNTER TOP
FRONT PANEL
B-10.1
4" RECESSED
36"
ST1
2" THICK
TRANSACTION
SURFACE
12"
6"
14" 54" 14"
82"
A
1 PLAN
1/2" = 1'-0" MFN-313.1
ST1
2" TRANSACTION COUNTER
4 1/8" REVEAL
SS2
2 2" WORKING
COUNTER TOP
WD4
WD1
43 1/2"
EXTENT AT
3'
ELEMENT
WD2
INSET PANEL
4"
3/8" REVEAL
1
3
WD4
A ELEVATION
2" FRONT PANEL
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
MFN-313.1
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number MFN-313 Gensler
Project Project Number
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
WD4 ST1
BEYOND 2" TRANSACTION COUNTER
1/8" REVEAL
SS2
2" WORKING COUNTER TOP
OPEN
3/8" REVEAL
43 1/2"
WD1
28 1/2"
WD2 WD2
BACK PANEL BASE & SHELVES
B ELEVATION
1/2" = 1'-0"
ST1
2" TRANSACTION COUNTER
1/8" REVEAL
WD1
SS2
SIDE PANELS &
1/2" SURROUND 2" WORKING
COUNTER TOP WD4
43 1/2"
EXTENT AT
3'
TRANSCTION
28 1/2"
ELEMENT
OPEN 3/8" REVEAL
4"
WD2 WD1
4" FRONT
BASE, SHELVES & SIDE PANELS PANEL BEYOND
DRAWER FRONTS
C ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
ST1
2" TRANSCTION COUNTER
1/8" REVEAL
SS2
2" WORKING COUNTER TOP
3/8" REVEAL
WD4
EXTENT AT
43 1/2"
TRANSCTION
4'
ELEMENT WD1
SIDE PANEL
4" FRONT
PANEL BEYOND
A ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
MFN-314.2
OPP.
B
C MFN-314.2
CAB-2.1 OPP.
P-1
SS2
30"
MFN-314.2 C
2" WORKING
COUNTER TOP
4" RECESSED FRONT PANEL
.
12"
6"
ST1
14" 54" 14" 2" TRANSACTION
COUNTER
82"
1 PLAN
MFN-314.1
1/2" = 1'-0"
ST1
2" TRANSACTION COUNTER
4 1/8" REVEAL
SS2
2 2" WORKING
COUNTER TOP
WD4
WD1
43 1/2"
EXTENT AT
.
ELEMENT
WD2
INSET PANEL
4"
3/8" REVEAL
1 3 WD4
2" FRONT PANEL
A ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
ST1
WD4 2" TRANSACTION COUNTER
BEYOND
1/8" REVEAL
SS2
OPEN 2" WORKING COUNTER TOP
43 1/2"
3/8" REVEAL
28 1/2"
OPEN
WD1
SIDE PANELS & SURROUND
4"
SS2
2" WORKING
COUNTER TOP
43 1/2"
WD4
3'
EXTENT AT
28 1/2"
TRANSCTION
3/8" REVEAL ELEMENT
4"
C ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
MFN-315.2
OPP.
SS2
2" WORKING
FRONT PANEL
4" RECESSED
COUNTER TOP
P-1 P-1
30"
C MFN-315.2
MFN-315.2 C
OPP.
12"
ST1
6"
2" TRANSACTION 14" 62" 14"
COUNTER
90"
1 PLAN
MFN-315.1
1/2" = 1'-0"
ST1
2" TRANSACTION COUNTER
4 1/8" REVEAL
SS2
2
2" WORKING
COUNTER TOP
WD1
43 1/2"
WD4
3'
WD2 TRANSCTION
ELEMENT
INSET PANEL
4"
3/8" REVEAL
1 3 WD4
2" FRONT PANEL
A ELEVATION
1/2" = 1'-0"
RECEPTION DESK
Drawing Scale Date
AS NOTED 07.30.10
WD4 ST1
BEYOND 2" TRANSACTION COUNTER
1/8" REVEAL
SS2
2" WORKING COUNTER TOP
OPEN
3/8" REVEAL
43 1/2"
28 1/2"
WD1
OPEN
SIDE PANELS &
1/2" SURROUND
4"
WD2 WD2
B ELEVATION BACK PANEL BASE & DRWAER
1/2" = 1'-0" FRONTS
ST1
2" TRANSACTION COUNTER
1/8" REVEAL
SS2
2" WORKING COUNTER TOP
43 1/2"
WD4
.
EXTENT AT
28 1/2"
TRANSCTION
3/8" REVEAL
ELEMENT
4"
C ELEVATION
1/2" = 1'-0"
DISPLAY TABLE
Drawing Scale Date
AS NOTED 07.30.10
48"
30"
SS1
A
1 1/2" COUNTER TOP
1 PLAN
1/2"=1'-0"
SS1 SS1
1 1/2" COUNTER TOP 1 1/2" COUNTER TOP
1 1/2"
3/8" REVEAL
28 1/2"
WD2
28 1/2"
WD2
A ELEVATION B ELEVATION
1/2" = 1'0" 1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
MFN-316
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number MFN-317 Gensler
Project Project Number
24"
SS1
1 1/2" COUNTER TOP
24"
A SS1
PRIVACY DIVIDER
MT1
1 1/2" BLACKENED
STEEL LEGS &
SUPPORT BELOW
1 PLAN
1/2" = 1'-0"
22" 2"
SS1
PRIVACY
DIVIDER
SS1
9 1/2"
MT1
1 1/2" BLACKENED
STEEL
A ELEVATION
1/2" = 1'-0"
ITEM NUMBER X
HOLES FOR ELECTRICAL
AND AIRFLOW MFN-318.1 30"
MFN-318.2 60"
WD2
CD PLAYER HOUSING WITH MFN-318.3 90"
REMOVABLE 3/4" TOP; TO
EQ
HOLD CD PLAYERS ON
EACH SIDE
ITEM NUMBER X
1/8" REVEAL
SUPPORT BELOW QLS-302.1 30"
QLS-302.2 60"
B CRM-302.3 90"
X
SS1
1 1/2" COUNTER TOP
EQ
PANEL BELOW
50"
1 PLAN
1/2" = 1'-0"
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
SIGNAGE
A ELEVATION
1/2" = 1'-0" WD2
3/4" CD SHELF AS
SCHEDULED
22"
SS1
MIN 1 1/2"
COUNTER TOP
WD2
3/8" REVEAL, TYP
28 1/2"
WD1
END PANEL
SUPPORT
B ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
87"
WD1
FINISHED
18"
1 PLAN MFN-322
1/2" = 1'-0"
1 1/2" DOOR
TRIM
D
SS1
TYP 4
1 1/2" TOP
8
3/8" REVEAL
5
WD1
SIM EXPOSED INSIDE FACES,
36"
MT1
1 1/2"
5 BLACKENED
WD2
STEEL LEG
3/8" RECESSED SHELVES AND
PANEL DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
12" 40"
B-11.4
MFN-323
1 PLAN
1/2" = 1'-0"
SS1
1 1/2" TOP
8
3/8" REVEAL
7 WD1
SIM EXPOSED INSIDE FACES, SIDE
36"
3/8" REVEAL
WD2
BASE, TOE KICK &
7 SHELVES
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
94 7/8"
18"
F-3.3 F-3.3
B-5.3
1 PLAN
MFN-324
1/2" = 1'-0"
SS1
1/2" TOP
8
3/8" REVEAL
7
WD1
28 1/2"
SIM
EXPOSED INSIDE
FACES, SIDE PANELS &
1/2" SURROUND
3/8" REVEAL
7
WD2
TOE KICK, BASE,
A ELEVATION SHELVES &
DRAWERS FRONTS
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
76"
12"
B-5.4 B-5.4
1 PLAN
MFN-325
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
7 WD1
EXPOSED INSIDE FACES, SIDE
28 1/2"
SIM
PANELS & SURROUND
3/8" REVEAL
7 WD2
TOE KICK, BASE &
SHELVES
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
58"
18"
B-11.2 CAB-15.5
1 PLAN MFN-326
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
7
EXPOSED INSIDE
FACES, SIDE PANELS &
SIM
36"
1/2" SURROUND
3/8" REVEAL
WD2
7
BASE, TOE KICK, SHELVES
& DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
52"
12"
B-5.2 B-5.2
1 PLAN MFN-327
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
7 WD1
EXPOSED INSIDE FACES, SIDE
28 1/2"
WD2
BASE, TOE KICK &
7 SHELVES
A ELEVATION
1/2" = 1'-0"
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
76"
WD1
FINISHED BACK
12"
1 PLAN
MFN-328
1/2" = 1'-0"
7
WD1
SIM EXPOSED INSIDE FACES, 1/2"
36"
WD2
7 TOE KICK, BASE &
A ELEVATION SHELVES
1/2" = 1'-0"
WD2
2X2 BOX JOINTS
WD1
SIDE PANEL
36"
WD2
2X2 BOX JOINTS
WD2
BASE
B ELEVATION
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
MFN-328
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number MFN-329 Gensler
Project Project Number
BOOKSHELF
Drawing Scale Date
AS NOTED 07.30.10
MFN-329
B-3.4 B-3.4
24"
B MFN-329
B-3.4 B-3.4
A
1 PLAN
1/2" = 1'-0" MFN-329
6
7 WD2
BASE, TOE KICK &
SIM SHELVES
WD1
50"
A ELEVATION 7
WD1
50"
SIDE PANEL
WD2
2X2 BOX JOINTS
WD2
B ELEVATION BASE
1/2" = 1'-0"
S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
101 Marietta Street NW
MFN-329
Suite 3000
Atlanta GA 30303
© 2010 Gensler Tel: 404.507.1000
Furniture Number MFN-330 Gensler
Project Project Number
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
90"
18"
A
1 PLAN
1/2" = 1'-0" MFN-330
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
7 EXPOSED INSIDE FACES, SIDE
28 1/2"
7
WD2
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
86"
CAB-10
B-3.2 B-3.2
A
GL1
TEMPERED GLASS INSET
MFN-331 WD2
1 PLAN
1 1/2" FRAME
1/2" = 1'-0"
GL1
6" GLASS DISPLAY
SHELF BELOW
WD2
LOCKABLE DOOR
6 BOTTOM HINGE 3/8" REVEAL
7
WD1
SIM
36"
7 WD2
BASE, TOE KICK & SHELVES
1/2" REVEAL
A ELEVATION
GL1
1/2" = 1'-0" CLEAR TEMPERED GLASS DOOR
& SHELF; SHELF TO HAVE PENCIL
POLISHED EDGE
WD2
LOCKABLE DRAWER &
1 1/2" DOOR FRAME
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
123"
WD1
FINISHED BACK
WD1
FINISHED
18"
MFN-332
1 PLAN
1/2" = 1'-0"
SS1
D
1 1/2" TOP
TYP 4
8 3/8" REVEAL
7
WD1
SIM EXPOSED INSIDE FACES,
36"
MT1
1 1/2"
5 WD2
3/8" RECESSED BLACKENED
PANEL BASE, SHELVES STEEL LEG
& DOOR FRONTS
A ELEVATION 1 1/2" DOOR TRIM
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
147"
WD1
FINISHED BACK
WD1
FINISHED
12"
1 PLAN
MFN-333
1/2" = 1'-0"
SS1
1 1/2" TOP
8
3/8" REVEAL
5
WD1
SIM EXPOSED INSIDE
36"
FACES, SIDE
PANELS & 1/2"
SURROUND
MT1
5 WD2 BLACKENED
BASE & SHELVES STEEL LEG
2 ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
94"
18"
A
1 PLAN
1/2" = 1'-0" MFN-334
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
7
EXPOSED INSIDE FACES, SIDE
28 1/2"
WD2
7
BASE, TOE KICK & DRAWER
FRONTS
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
88"
18"
CAB-11.1 CAB-15.1
B-10.4
1 PLAN
MFN-335
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
7
EXPOSED INSIDE FACES, SIDE
28 1/2"
WD2 7 WD2
SHELVES BASE, TOE KICK
& DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
72"
18"
1 PLAN MFN-336
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8 WD2
DRAWER, TYP.
WD1
7
EXPOSED INSIDE FACES, SIDE
36"
7 WD2
BASE, TOE KICK, SHELVES &
DOOR FRONTS
A ELEVATION
1/2" = 1'-0"
DESK
Drawing Scale Date
AS NOTED 07.30.10
154"
30"
MFN-337
1 PLAN
1/2" = 1'-0"
SS1 WD1
1 1/2" TOP EXPOSED INSIDE
FACES, SIDEPANELS
6 & 1/2" SURROUNDS
7
28 1/2"
OPEN
SIM
7 WD2
BASE, TOE KICK,
A ELEVATION DOORS & DRAWER
FRONTS
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
93 7/8"
18"
F-4.3
B-11.3 B-11.3
1 PLAN
1/2" = 1'-0" MFN-338
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
EXPOSED INSIDE
FACES, SIDE PANELS
36"
WD2
7
TOE KICK, BASE,
SHELVES & DRAWER
FRONTS
A ELEVATION
1/2" = 1'-0"
CASEGOOD COMBINATION
Drawing Scale Date
AS NOTED 07.30.10
72"
18"
1 PLAN
MFN-339
1/2" = 1'-0"
SS1
1 1/2" TOP
3/8" REVEAL
8
WD1
EXPOSED INSIDE
FACES, SIDE PANELS &
36"
1/2" SURROUNDS
7
3/8" REVEAL
SIM
WD2 7 WD2
TOE KICK, BASE & BASE, TOE KICK, SHELVES
DOOR FRONTS & DRAWER FRONTS
A ELEVATION
1/2" = 1'-0"
INDEX
Scale:
Gensler © 2010 Page Number 00-00
NOTES
12"
1
FIXED SHELF
13" MIN.
TYP
SECTION 1 ELEVATION
B-1 BOOKCASE
COMPONENT ID WIDTH NOTES
B-1.1 18" OPEN BACK STORAGE
B-1.2 24" OPEN BACK STORAGE
B-1.3 30" OPEN BACK STORAGE
B-1.4 36" OPEN BACK STORAGE
B-1
Scale: 1/2" = 1'-0" STORAGE SHELF
Gensler © 2010 Page Number 01-01
12"
WIDTH AS SCHEDULED
SEE SPECIFICATIONS
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
13" MIN
TYP
7'-9"
CUSTOM FURNITURE PIECE BELOW. REFER TO
PLAN.
SECTION ELEVATION
B-2 BOOKCASE
COMPONENT ID WIDTH NOTES
B-2.1 18" BEGINS 28 1/2" FROM FINISH FLOOR
B-2.2 24" BEGINS 28 1/2" FROM FINISH FLOOR
B-2.3 30" BEGINS 28 1/2" FROM FINISH FLOOR
B-2.4 36" BEGINS 28 1/2" FROM FINISH FLOOR
B-2
Scale: 1/2" = 1'-0" BOOKSHELF ABOVE CABINET
Gensler © 2010 Page Number 01-02
NOTES
WIDTH
AS SCHEDULED
12"
1
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
SEE SPECIFICATIONS
13" MIN.
TYP
SECTION 1 ELEVATION
B-3 BOOKCASE
COMPONENT ID WIDTH NOTES
B-3.1 18" 2 INTERIOR SHELVES
B-3.2 24" 2 INTERIOR SHELVES
B-3.3 30" 2 INTERIOR SHELVES
B-3.4 36" 2 INTERIOR SHELVES
B-3
Scale: 1/2" = 1'-0" BOOKSHELF - LOW DISPLAY
Gensler © 2010 Page Number 01-03
NOTES
WIDTH AS SCHEDULED 1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
12" 1 2 SOLID WOOD BASE WITH TOE KICK
SEE SPECIFICATIONS
1'-1" MIN
TYP
SECTION 1 ELEVATION
B-4 BOOKCASE
COMPONENT ID WIDTH
B-4.1 18"
B-4.2 24"
B-4.3 30"
B-4.4 36"
B-4
Scale: 1/2" = 1'-0" HIGH BOOKSHELF
Gensler © 2010 Page Number 01-04
NOTES
WIDTH
12" AS SCHEDULED
SEE SPECIFICATIONS
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
13" MIN
TYP
SECTION 1 ELEVATION
B-5 BOOKSHELF LOW
COMPONENT ID WIDTH
B-5.1 18"
B-5.2 24"
B-5.3 30"
B-5.4 36"
B-5
Scale: 1/2" = 1'-0" LOW BOOKSHELF
Gensler © 2010 Page Number 01-05
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
WIDTH
12" AS SCHEDULED 2 BASE TO BE HARDWOOD
3 SOLID WOOD BASE WITH TOE KICK
1 4 BASE TO HAVE HEAVY DUTY NON COROSIVE
LEVELERS
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
13" MIN
TYP
SECTION 1 ELEVATION
B-6 BOOK SHELF
COMPONENT ID WIDTH
B-6.1 18"
B-6.2 24"
B-6.3 30"
B-6.4 36"
B-6
Scale: 1/2" = 1'-0" HIGH BOOKSHELF
Gensler © 2010 Page Number 01-06
NOTES
WIDTH 1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
12" AS SCHEDULED AND IMPERVIOUS TO OILS
2 SOLID WOOD BASE WITH TOE KICK
1 3 BASE TO HAVE HEAVY DUTY NON COROSIVE
LEVELERS
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
18" MIN
TYP
SECTION 1 ELEVATION
B-7 BOOKCASE
COMPONENT ID WIDTH NOTES
B-7.1 18" TO FIT LEGAL SIZED FILES
B-7.2 36" TO FIT LEGAL SIZED FILES
B-7
Scale: 1/2" = 1'-0" HIGH BOOKSHELF
Gensler © 2010 Page Number 01-07
NOTES
WIDTH
AS SCHEDULED
12"
1
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
16" MIN
TYP
SECTION 1 ELEVATION
B-8 BOOKCASE
COMPONENT ID WIDTH NOTES
B-8.1 18" TO FIT LEGAL SIZED FILES
B-8.2 36" TO FIT LEGAL SIZED FILES
B-8
Scale: 1/2" = 1'-0" LOW FOLDER SHELF
Gensler © 2010 Page Number 01-08
NOTES
21"
WIDTH AS SCHEDULED
1
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
SEE SPECIFICATIONS
INCREMENTS
1"
PEDESTAL FILE, LEGAL SIZE
SECTION 1 ELEVATION
B-9 BOOKCASE
COMPONENT ID WIDTH DEPTH
B-9 19" 22"
B-9
Scale: 1/2" = 1'-0" SUPERVISOR STAND
Gensler © 2010 Page Number 01-09
NOTES
1
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
13" HOLD
SECTION 1 ELEVATION
B-10 BOOKCASE
COMPONENT ID WIDTH DEPTH
B-10.1 18" 12"
B-10.2 24" 12"
B-10.3 30" 12"
B-10.4 36" 12"
B-10
Scale: 1/2" = 1'-0" BOOKSHELF
Gensler © 2010 Page Number 01-10
NOTES
WIDTH
AS SCHEDULED
12" 1
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
SECTION 1 ELEVATION
B-11 BOOKCASE
COMPONENT ID WIDTH DEPTH
B-11.1 18" 12"
B-11.2 24" 12"
B-11.3 30" 12"
B-11.4 36" 12"
B-11
Scale: 1/2" = 1'-0" BOOKSHELF
Gensler © 2010 Page Number 01-11
NOTES
WIDTH
AS SCHEDULED
SEE SPECIFICATION
EQ
3"
1" 1" EQ
4"
ELEVATION
B-13 BOOKCASE
COMPONENT ID WIDTH
B-13.1 24" DIA.
B-13.2 30" DIA.
B-13.3 36" DIA.
B-13.4 42" DIA.
B-13
Scale: 1/2" = 1'-0" BOOKSHELF
Gensler © 2010 Page Number 01-13
NOTES
WIDTH
AS SCHEDULED
DEPTH AS SCHEDULED
INTERIOR OF CABINET TO BE PLASTIC LAMINATE, 1
REFER TO SPECIFICATION
SEE SPECIFICATIONS
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
13" MIN
TYP
SECTION 1 ELEVATION
CAB-1 LARGE BIN CABINET
COMPONENT ID WIDTH DEPTH NOTES
CAB-1.1A 36" 15" CENTER SUPPORT INCLUDED
CAB-1.1B 36" 24" CENTER SUPPORT INCLUDED
CAB-1.2A 42" 15" CENTER SUPPORT INCLUDED
CAB-1.2B 42" 24" CENTER SUPPORT INCLUDED
CAB-1.3A 48" 15" CENTER SUPPORT INCLUDED
CAB-1.3B 48" 24" CENTER SUPPORT INCLUDED
CAB-1
Scale: 1/2" = 1'-0" LARGE BINS CABINET
Gensler © 2010 Page Number 02-01
NOTES
DEPTH
AS SCHEDULED 1
SEE SPECIFICATIONS
DRAWER
6"
CUT OUTS FOR WIRE MANAGEMENT
SECTION 1 ELEVATION
CAB-2 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-2 20" 18" INTERIOR DIM TO FIT SCHEDULED PRINTER
CAB-2
Scale: 1/2" = 1'-0" PRINTER CABINET
Gensler © 2010 Page Number 02-02
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
2 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
DEPTH WIDTH
AS SCHEDULED AS SCHEDULED
1
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
SEE SPECIFICATIONS
INCREMENTS
SECTION 1 ELEVATION
CAB-5 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-5 18" 15" TO FIT LEGAL SIZE PAPER
CAB-5
Scale: 1/2" = 1'-0" TIME MACHINE & JOB SORTER
Gensler © 2010 Page Number 02-05
DEPTH 1
AS SCHEDULED WIDTH AS SCHEDULED
NOTES
15" 1 REFER TO SPECIFICATION FOR DECORATIVE
HARDWARE SPECIFICATION
2 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
3 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
4 SOLID WOOD BASE WITH TOE KICK
SECTION 1 ELEVATION
CAB-6 CABINETS
COMPONENT ID WIDTH DEPTH
CAB-6 90" 24"
CAB-6
Scale: 1/2" = 1'-0" AOHM CABINET
Gensler © 2010 Page Number 02-06
NOTES
1 REFER TO FF&E CASEGOODS DETAIL APPENDIX
FOR TYPICAL EDGE DETAIL
2 SOLID WOOD BASE WITH TOE KICK
WIDTH
AS SCHEDULED
1
1" FIXED SHELVES W/ SOLID WOOD LIP
SEE SPECIFICATIONS
SUPPORTED BY CONTINUOUS BLOCKING
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
REFER TO SPECIFICATION
CUT OUTS FOR WIRE MANAGEMENT
5" MIN.
TYP
SECTION 1 ELEVATION
CAB-7 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-7 36" 12" TO FIT SIMULATORS (15 1/4"W X 4 1/4"H
X 9 1/2"D)
CAB-7
Scale: 1/2" = 1'-0" SIMULATOR CABINET
Gensler © 2010 Page Number 02-07
NOTES
DEPTH
AS SCHEDULED
1
SEE SPECIFICATIONS
PULL OUT SHELF
6"
REFER TO SPECIFICATION
CUT OUTS FOR WIRE MANAGEMENT
9"
SECTION 1 ELEVATION
CAB-2 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-2 20" 18" INTERIOR DIM TO FIT SCHEDULED PRINTER
CAB-8
Scale: 1/2" = 1'-0" PRINTER CABINET
Gensler © 2010 Page Number 02-08
NOTES
18" 3'-2"
SEE SPECIFCATIONS
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
SECTION 1 ELEVATION
CAB-9 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-9.1 24" 18" 2 CABINET DOORS, TYP.
CAB-9.2 30" 18" 2 CABINET DOORS, TYP.
CAB-9.3 36" 18" 2 CABINET DOORS, TYP.
CAB-9
Scale: 1/2" = 1'-0" UNDER COUNTER STORAGE CABINET
Gensler © 2010 Page Number 02-09
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
SECTION 1 ELEVATION
CAB-11 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-11.1 24" 18" MUST FIT 14" BY 18" MAX CERTS
CAB-11.2 30" 18" MUST FIT 14" BY 18" MAX CERTS
CAB-11
Scale: 1/2" = 1'-0"
Gensler © 2010 Page Number 02-11
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
SEE SPECIFICATIONS
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
CUT OUTS FOR WIRE MANAGEMENT
SECTION 1 ELEVATION
CAB-12 CABINETS
COMPONENT ID WIDTH DEPTH
CAB-12 30" 15"
CAB-12
Scale: 1/2" = 1'-0" COURSE ROOM AV CABINET
Gensler © 2010 Page Number 02-12
NOTES
SEE SPECIFICATIONS
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
REFER TO SPECIFICATION
SECTION 1 ELEVATION
CAB-14 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-14.1A 24" 18" 2 CABINET DOORS, TYP.
CAB-14.1B 24" 24" 2 CABINET DOORS, TYP.
CAB-14.2A 36" 18" 2 CABINET DOORS, TYP.
CAB-14.2B 36" 24" 2 CABINET DOORS, TYP.
CAB-14.3A 48" 18" 2 CABINET DOORS, TYP.
CAB-14.3B 48" 24" 2 CABINET DOORS, TYP.
CAB-14
Scale: 1/2" = 1'-0" HIGH SUPPLIES CABINET
Gensler © 2010 Page Number 02-14
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
2 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
WIDTH AS SCHEDULED
DEPTH AS SCHEDULED
1
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
SEE SPECIFICATIONS
SEE SPECIFICATIONS
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
SECTION 1 ELEVATION
CAB-15 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-15.1 24" 15" 2 CABINET DOORS, TYP.
CAB-15.2 30" 15" 2 CABINET DOORS, TYP.
CAB-15.3 36" 15" 2 CABINET DOORS, TYP.
CAB-15.4 30" 18" 2 CABINET DOORS, TYP.
CAB-15.5 30" 15" 2 CABINET DOORS, TYP.
CAB-15.6 36" 15" 2 CABINET DOORS, TYP.
CAB-15
Scale: 1/2" = 1'-0" STORAGE UNDER RETURN
Gensler © 2010 Page Number 02-15
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
2 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
DEPTH WIDTH
AS SCHEDULED AS SCHEDULED
SEE SPECIFICATIONS
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
SECTION 1 ELEVATION
CAB-16 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-16.1A 24" 15" 2 CABINET DOORS, TYP.
CAB-16.1B 24" 24" 2 CABINET DOORS, TYP.
CAB-16.2A 36" 15" 2 CABINET DOORS, TYP.
CAB-16.2B 36" 24" 2 CABINET DOORS, TYP.
CAB-16.3A 48" 15" 2 CABINET DOORS, TYP.
CAB-16.3B 48" 24" 2 CABINET DOORS, TYP.
CAB-16
Scale: 1/2" = 1'-0" SERVICE CREDENZA
Gensler © 2010 Page Number 02-16
NOTES
WIDTH
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AS SPECIFIED AND IMPERVIOUS TO OILS
2 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
AS SPECIFIED
3 SOLID WOOD BASE WITH TOE KICK
DEPTH
4 BASE TO HAVE HEAVY DUTY NON COROSIVE
LEVELERS
PLAN 1
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
SEE SPECIFICATIONS
ELEVATION 1
CAB-17 CABINETS
COMPONENT ID WIDTH DEPTH NOTES
CAB-17 54" DIAG. 2 CABINET DOORS, TYP.
CAB-17
Scale: 1/2" = 1'-0"
Gensler © 2010 Page Number 02-17
NOTES
SEE SPECIFICATIONS
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
REFER TO SPECIFICATION
SECTION 1 ELEVATION
CAB-19 CABINETS
COMPONENT ID WIDTH NOTES
CAB-19.1 24" 2 CABINET DOORS, TYP.
CAB-19.2 36" 2 CABINET DOORS, TYP.
CAB-19.3 48" 2 CABINET DOORS, TYP.
CAB-19
Scale: 1/2" = 1'-0" UNIFORM STORAGE CABINET
Gensler © 2010 Page Number 02-19
NOTES
18"
SEE SPECIFICATIONS
CUTOUT FOR ACCESS TO SCHEDULED OUTLET
DEVICE
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS DOORS TO HAVE TOUCH LATCH, SILENCERS AND
HEAVY DUTY HINGES, HEFFELE OR DESIGNER
INTERIOR OF CABINET TO BE PLASTIC LAMINATE, APPROVED ALTERNATE
REFER TO SPECIFICATION
SECTION 1 ELEVATION
CAB-20
Scale: 1/2" = 1'-0" AV CABINET
Gensler © 2010 Page Number 02-20
NOTES:
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
2 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
3 SOLID WOOD BASE WITH TOE KICK
4 BASE TO HAVE HEAVY DUTY NON COROSIVE
LEVELERS
DEPTH WIDTH
AS SCHEDULED AS SCHEDULED
SEE SPECIFICATION
EQ
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
REFER TO SPECIFICATION
EQ
AND BACK STOPS
SECTION 1 ELEVATION
F-3 - LATERAL FILE CABINET 2 DRAWER
COMPONENT ID WIDTH DEPTH
F-3.1 18" 18"
F-3.2 24" 18"
F-3.3 30" 18"
F-3.4 36" 18"
F-3
Scale: 1/2" = 1'-0" LATERAL FILE
Gensler © 2010 Page Number 04-03
NOTES
1
FILE HOLDING APPARATUS
SEE SPECIFICATIONS
EQ
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
REFER TO SPECIFICATION
EQ
DRAWERS MUST HAVE HEAVY DUTY SIDE
MOUNTED BALL BEARING GLIDES WITH FRONT
AND BACK STOPS
SECTION 1 ELEVATION
F-4 - LATERAL FILES UNDER COUNTER
COMPONENT ID WIDTH DEPTH NOTES
F-4.1 18" 18" HOLDS HANGING LEGAL SIZE FILES
F-4.2 24" 18" HOLDS HANGING LEGAL SIZE FILES
F-4.3 30" 18" HOLDS HANGING LEGAL SIZE FILES
F-4.4 36" 18" HOLDS HANGING LEGAL SIZE FILES
F-4
Scale: 1/2" = 1'-0" LATERAL FILES UNDER COUNTER
Gensler © 2010 Page Number 04-04
NOTES
28" 40"
SEE SPECIFICATIONS
3"
SECTION 1 ELEVATION
F-5 - FLAT FILES UNDER COUNTER
COMPONENT ID WIDTH DEPTH NOTES
F-5 40" 28" FITS 24" BY 36" PAPER
F-5
Scale: 1/2" = 1'-0" FLAT FILES UNDER COUNTER
Gensler © 2010 Page Number 04-05
NOTES
WIDTH
12" AS SCHEDULED 1 HANG 20" MIN. ABOVE TOP OF FURNITURE
BELOW
SEE SPECIFICATIONS
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
13" MIN
LIP. SHELF TO BE ADJUSTABLE AT 2"
TYP
INCREMENTS
SECTION 1 ELEVATION
O-1 OVERHEAD
COMPONENT ID WIDTH NOTES
O-1.1 18" OFFSET 50" FROM GROUND
O-1.2 36" OFFSET 50" FROM GROUND
O-1.3 24" OFFSET 50" FROM GROUND
O-1.4 30" OFFSET 50" FROM GROUND
O-1
Scale: 1/2" = 1'-0" OVERHEAD
Gensler © 2010 Page Number 06-01
WIDTH
12" AS SCHEDULED
1
1 ADJUSTABLE SHELF W/ SOLID WOOD LIP.
SHELF TO BE ADJUSTABLE AT 3/4" INCREMENTS
WITH 5 POSSIBLE POSTIONS DIVIDER SUPPORTS; REFER TO SPECIFICATION
FOR QUANTITY AND LOCATION
SEE SPECIFICATIONS
13" MIN
TYP
1" THICK ADJUSTABLE SHELF W/ SOLID WOOD
LIP. SHELF TO BE ADJUSTABLE AT 2"
INCREMENTS
26"
ANCHORING
SITS ON DESK
28 1/2"
SECTION 1 ELEVATION
O-2 OVERHEAD
COMPONENT ID WIDTH
O-2.1 18"
O-2.2 24"
O-2.3 30"
O-2
Scale: 1/2" = 1'-0" HUTCH FOR DESK
Gensler © 2010 Page Number 06-02
11 3/4"
1
17"
SEE SPECIFICATIONS
1/2"
FIXED SHELF 1/2"
FIXED SHELF
1"
13"
SORTING INSERT TO FIT WITHIN LARGER
CUSTOM PIECE
1/2"
1"
SECTION 1 ELEVATION
O-3 OVERHEAD
COMPONENT ID WIDTH DEPTH NOTES
O-3 17" 11 3/4" TO FIT INSIDE OVERHEAD UNIT
O-3
Scale: 1/2" = 1'-0" OVERHEAD SORTING INSERT
Gensler © 2010 Page Number 06-03
NOTES
WIDTH
1 HANG 20" MIN. ABOVE TOP OF CABINET BELOW
12" AS SCHEDULED
2 PROVIDE CONTINUOUS CLEAT FOR WALL
ANCHORING
1
SEE SPECIFICATIONS
CABINET
SECTION 1 ELEVATION
O-4 OVERHEAD
COMPONENT ID WIDTH DEPTH NOTES
O-4.1 24" 12" 2 CABINET DOORS/OFFSET 50" FROM
GROUND
O-4.2 30" 12" 2 CABINET DOORS/OFFSET 50" FROM
GROUND
O-4.3 36" 12" 2 CABINET DOORS/OFFSET 50" FROM
GROUND
O-4
Scale: 1/2" = 1'-0" OVERHEAD STORAGE CABINET
Gensler © 2010 Page Number 06-04
NOTES
18"
24"
SEE SPECIFICATIONS
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
12" 5 1/2"
REFER TO SPECIFICATION
SECTION 1 ELEVATION
P-1 PEDESTAL
COMPONENT ID WIDTH DEPTH
P-1 18" 24"
P-1
Scale: 1/2" = 1'-0" FOR GENERAL STAFF
Gensler © 2010 Page Number 08-01
NOTES
1 TOP OF UNIT TO BE HEAT AND STAIN RESISTANT
AND IMPERVIOUS TO OILS
2 CONTINUOUS TOP W/ SOLID WOOD EDGE,
REFER TO SPECIFICATION
15" 18"
SEE SPECIFICATIONS
EQ EQ
INTERIOR OF CABINET TO BE PLASTIC LAMINATE,
REFER TO SPECIFICATION
11"
SECTION 1 ELEVATION
P-2 PEDESTAL
COMPONENT ID WIDTH DEPTH
P-2 18" 15"
P-2
Scale: 1/2" = 1'-0" PEDESTAL FOR RETURN
Gensler © 2010 Page Number 08-02
DRAWING NOTES
21F 22F 23F 24F 25F 26F 27F 28F CHURCH OF
SCIENTOLOGY
2 / A06.10.B
MATCHLINE
CLASS V ORG - TAMPA
UP
WTR-502.1 STAIR 3 1300 East 8th Ave
Tampa, FL 33605
DF
(S)B-1.1 (S)B-1.1 (S)B-1.1
(S)F-5
(S)O-1.4
(S)CAB-5
B-10 MFN-321
(S)D-8.2l
MANTIENANCE OFFICER D-11.1 (S)P-1
(S)B-1.4
(S)B-1.4
(S)B-1.4
(S)B-1.4
MFN-310.1
S-14
T-11
(S)O-1.4
NANNY
S-5
S-5
MFN-400
(S)P-1
LFN-402 LFN-400
(S)B-1.4
(S)B-1.4
(S)B-1.4
(S)B-1.4
LFN-900 WORK AREA
F007
(S)F-5
(S)O-1.4
MECHANICAL ESTATES
F001
101 Marietta Street NW
OFFICE MFN-320
(S)D-8.2l
F002 Suite 3000
(S)B-1.4
Gensler
(S)B-1.4
(S)B-1.4
(S)B-1.4
CAB-14
Atlanta GA 30303
LFN-400
S-5
Tel: 404.507.1000
(S)O-1.4
ESTATES
SHEET NOTES
(S)P-1
MANAGER
(S)B-1.4
(S)B-1.4
LFN-400
BOOKSTOCKS
HGC FOLDER
STORAGE
CF A00.00
CAB-14
F009 F010 (S)D-8.1j (S)CAB-2
MFN-320 (S)P-1
(S)P-1
(S)O-1.3 (S)O-1.3 (S)O-1.4 (S)O-1.4
RST-700
CORRIDOR
F003
(S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8 (S)B-3.8
BF
MATCHLINE
2 / A06.10.B
LEGEND ISSUE DATE DESCRIPTION BY CK
CUSTOM FURNITURE
SYSTEMS FURNITURE
PURCHASED FURNITURE
AF
CORRIDOR
F004
ELEVATOR
EQUIPMENT
ROOM
F005
Seal/Signature
KEY PLAN
Project Name
LOBBY CLASS V ORG - TAMPA
F006
Project Number
13.7042.430
Scale
1/4" = 1'-0"
C
Ref. North
A06.10.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:23 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
28F 29F 30F 31F 32F 33F 34F 35F
CHURCH OF
SCIENTOLOGY
MATCHLINE
1 / A06.10.A
CLASS V ORG - TAMPA
WTR-502.1 WTR-502.1
1300 East 8th Ave
Tampa, FL 33605
DF
HDF-902
S-18
S-18
S-18
S-18
S-18
S-18
ELECTRICAL
T-16.3
T-16.3
T-16.3
ROOM
F016
S-18
S-18
S-18
S-18
S-18
S-18
PUMP ROOM
F017
S-18
S-18
S-18
S-18
S-18
S-18
F-6
S-18
S-18
S-18
S-18
S-18
S-18
T-16.3
T-16.3
T-16.3
S-18
S-18
S-18
S-18
S-18
S-18
101 Marietta Street NW
LFN-404 ; TYP Suite 3000
LFN-300 ; TYP
STAFF LUNCH
ROOM
Gensler Atlanta GA 30303
Tel: 404.507.1000
(S)D-8.2l F-6
(S)CAB-2 (S)P-1
TEL CLOSET
(S)O-1.4 (S)O-1.4 ELEVATOR F020
EQUIPMENT ELECTRICAL
ROOM ROOM
F018 F019
UP STAIR 2
2
TREASURY
STORAGE
F012
BF
MATCHLINE
1 / A06.10.A
T-9
T-9
T-9
S-8
S-8
S-8
MILLWORK, REFER TO SPACE PLAN
CUSTOM FURNITURE
(S)CAB-2
MFN-400 MFN-401
(S)D-11.1
(S)D-8.1g
S-5
S-2
REGISTRATION WTR-502.2
SYSTEMS FURNITURE
(S)F-3.1
F127
PLANTER
METER
TEST MARKING CHECK MFN-302
1 / A06.11.B 1 / A06.11.B PURCHASED FURNITURE
S-2
S-2
S-16
MFN-400 MFN-400 MFN-406 WTR-502.2
S-5
S-5
(S)D-11.1
(S)D-11.1
MFN-302 T-5
(S)P-1 (S)P-1
(S)D-3.1a (S)D-3.1a
WTR-502.2
MFN-302 T-5
PUBLIC REGISTRAR
WTR-502.2
Seal/Signature
MFN-401
S-2
S-2
S-16
MFN-400
MFN-401
MFN-400
MFN-406
KEY PLAN
S-5
S-5
(S)D-11.1
(S)D-11.1
MFN-302 T-5 WTR-502.2
PLANTER
(S)P-1 (S)P-1
(S)D-3.1a (S)D-3.1a
Project Name
CLASS V ORG - TAMPA
MFN-303A MFN-405 MFN-303B
WTR-502.2
Project Number
13.7042.430
T-5 T-5
C
Ref. North
A06.10.B
FURNITURE PLAN - FACTORY LEVEL 01 SOUTH 4
SCALE: 1/4" = 1'-0" © 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:25 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
21F 22F 23F 24F 25F 26F 27F 28F CHURCH OF
SCIENTOLOGY
MATCHLINE
1 / A06.11.B
CLASS V ORG - TAMPA
WTR-502.3 WTR-502.3 WTR-500.1 WTR-500.1 WTR-500.1 WTR-500.1 WTR-500.1 WTR-500.1
1300 East 8th Ave
Tampa, FL 33605
DF
S-3
MFN-337 MFN-418 MFN-308
F-3.4
T-5
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
DIN-402 ; TYP DIN-301 ; TYP
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-3
MFN-400 MFN-310.1 MFN-401
CAB-15.3
S- S-
18 18 18 18 COATS
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S- S-
S-2
MFN-418
F102
S-16
DIN-403 ; TYP
D-11.1
T- T-
6.4 6.4 CHAPLAIN
S-5
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
F101
(S)P-1
S- S-
18 18 MFN-401
S-2
18 18
S- S-
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S- 101 Marietta Street NW
CAB-2.1
18 18
S-
PLANTER Suite 3000
Gensler
DIN-900
T- Atlanta GA 30303
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
6.4
Tel: 404.507.1000
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-
18
S-
18
SHEET NOTES
40 5/8"
S- S- S-16
S-
18 18
S-
18 18
CPL-400 ; TYP CPL-400 CF A00.00
T- T-
6.4 6.4
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S- S-
18 18 18 18
S- S-
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
AUDITORIUM
F110
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
VESTIBULE
F103
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
DN
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
STAIR 5
5
TERRACE
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
F104B PORCH
F104A
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
AUD
S- S-
18 18 18 18
S- S-
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
T- T-
6.4 6.4
S-16
BF
S- S-
18 18 18 18
S- S-
S-11
S-11
S-
FLM-400 ; TYP
S-11
18 18
18
S-
S- S-
18
MEN'S
T- DIN-300 DIN-401 ; TYP RESTROOM
T-
B-3.4
6.4 6.4 F109
S-11
S-11
DV6-322
S-11
DIN-900 PLANTER
JANITOR
S-
CLOSET
18 18 S-
18
S- 18
S- F112
S-11
S-11
S-14
S-11
RST-700 RST-700 RST-700 PUBLIC VIDEO
B-3.4
ROOM
S-
18
S-
18
S-
18
S-
18
DIN-400 ; TYP
F114 LEGEND ISSUE DATE DESCRIPTION BY CK
S-11
S-16
S-14
B-3.4
S-
07.09.2010 75% CONSTRUCTION CS JA/ES
S-11
DOCUMENTATION
S- S- T-
18
S-
18 18
S-
18 6.4 MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION CS JA/ES
S-14
COATS
S-11
S-11
S-11
RST-700 RST-700 RST-700 F113
B-3.4
S-
18 18
S-
WOMEN'S
S-11
S-11
S-11
RESTROOM CUSTOM FURNITURE
DIN-300
F108 CORRIDOR
S-
F111
14
DN
B-3.4 B-3.4 B-3.4 B-3.4 B-3.4 B-3.4
S-
14
SYSTEMS FURNITURE
STAIR 6
6 DV6-320
PURCHASED FURNITURE
CAFE
F104 DIV 6 DISPLAYS
S- S-
18 18 18 18 F116
S- S-
T-
6.4
T-
6.4 AF
CAB-9.2 B-11.4 CAB-9.2
S- S-
S-16
18 18 18 18
S- S-
.3
B--2.4
15
CAB
CAB
B--2.4
LRH OFFICE
B-3.4
15
MFN-403 ; TYP DV6-321 DV6-300
.6
MAIN LRH-321 F115 LRH-322 LRH-321
S-
F-3.1 CAB-2.1 CAB-15.1
18 18
RECEPTION
S-
B-11.1
HFN-302
F107
S-6 S-6 S-6
T- LRH-401 LRH-302 LRH-401 DV6-100
6.4 T-5
WTR-502.2
S-5
B-3.2
CAB-20.1
B-11.4
S-
18 18 DIN-900 PLANTER LRH-320
S-
S-6
S-6
S- S- MFN-322 DV6-400
B-11.1
18 18 18 18
S- S- LRH-322 S-2 S-2 LRH-100
PUBLIC CONF
T-5.2
LRH-800 Seal/Signature
T-6
S-6 S-6 S-6 T-5
RM
T- T-
6.4 6.4 F105
KEY PLAN
CAB-15.5
S-16
S- S- WTR-502.2 HFN-401
18 18 18 18 S-3
S- S-
LRH-320
T-5
B-11.4
T-5
HFN-300
B-11.4
S-3
HFN-320 S-1
CAB-15.5
GLOBE
RECEPTION
B-3.4
DV6-321 DV6-300 DV6-301
LOBBY
STAIR 1 F106 LRH-300 LRH-400 Project Name
HFN-401
CLASS V ORG - TAMPA
Project Number
13.7042.430
1 / A06.11.B
Description
A B FURNITURE PLAN - FACTORY LEVEL 01 WEST
ELEVATOR
1
PLANTER
Scale
1/4" = 1'-0"
C
1F 2F 3F 4F 5F 6F 7F 8F Ref. North
A06.11.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:27 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
29F 30F 31F 32F 33F 34F 35F CHURCH OF
SCIENTOLOGY
MATCHLINE
1 / A06.11.A
CLASS V ORG - TAMPA
WTR-500.1 WTR-500.1 WTR-500.1 WTR-501 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3
1300 East 8th Ave
Tampa, FL 33605
DF
(S)B-10.1
(S)B-10.1
(S)B-10.1
(S)B-10.1
(S)CAB-9.3
(S)O-4.3
(S)O-4.3
(S)O-4.3
(S)O-4.3
(S)F-4.3
(S)F-4.3
(S)F-4.3
DIR PUBLIC BOOK SALES PUBLIC BOOKS DIR PUBLIC CONATCT PUBLIC CAMPAIGNS
DISTRIBUTION OFF PROMO OFF
S-19
S-19
S-19
S-19
S-19
S-5 S-5 S-5 S-5
(S)O-1.7
(S)O-1.7
(S)O-1.7
(S)D-11.1 (S)D-11.1 (S)D-11.1 (S)D-11.1
S-19
S-19
S-19
S-19
S-19
CPL-400 ;TYP WTR-502.2
P-1M P-1M P-1M P-1M
(S)CAB-9.3
(S)O-4.3
(S)O-4.3
(S)O-4.3
(S)O-4.3
(S)F-4.3
(S)F-4.3
(S)F-4.3
S-19
S-19
S-19
S-19
S-19
(S)O-1.1
P-1M P-1M P-1M P-1M
S-19
S-19
S-19
S-19
S-19
CHAIR (S)D-11.1 (S)D-11.1 (S)D-11.1 (S)D-11.1
(S)O-1.7
(S)O-1.7
(S)CAB-2
(S)CAB-9.3
STORAGE
(S)O-4.3
(S)O-4.3
(S)F-4.3
PUBLIC BOOKS EXTERNAL BOOK UNIT NEW PUBLIC CONTACT
F122
(S)B-10.1
(S)B-10.1
(S)B-10.1
(S)B-10.1
S-5 CAMPAIGNS OFF OFF PUBLIC INFO & METHOS OFF
S-5 S-5 S-5
S-19
S-19
S-19
S-19
S-19
DISPLAYS OFF
(S)O-1.8
S-19
S-19
S-19
S-19
S-19
WTR-502.2 101 Marietta Street NW
(S)CAB-9.3
(S)O-4.3
(S)O-4.3
(S)F-4.3
(S)B-10.1
(S)B-10.1
(S)B-10.1
BOOK ADS AND STREET Suite 3000
Gensler
INFO PACKS OFF BOOKSELLING I/C
(S)F-3.4 (S)F-3.4 (S)F-3.4 (S)F-3.4 (S)F-3.4 Atlanta GA 30303
S-19
S-19
S-19
S-19
S-19
S-5 S-5
(S)O-1.7
(S)O-1.7
(S)O-4.8 (S)O-4.8 (S)O-4.2
Tel: 404.507.1000
(S)D-11.1 (S)D-11.1
(S)B-10.3
(S)O-1.1
S-19
S-19
S-19
S-19
S-19
(S)CAB-2
DIV 6A SEC
P-1M P-1M
PLANTER
SHEET NOTES
(S)B-10.1
(S)O-1.2
LFN-400 ; TYP
S-5
CF A00.00
(S)F-3.3
(S)O-1.1
(S)P-1 LFN-400 ; TYP F121
S-19
S-19
S-19
S-19
F123
(S)P-1
(S)P-1
(S)P-1
(S)P-1
(S)O-1.1
(S)F-3.3
S-19
S-19
S-19
S-19
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)O-1.6
(S)O-1.6
(S)O-1.6
(S)O-1.6
(S)D-11.1
S-19
S-19
S-19
S-19
S-5
S-5
S-5
S-5
DIV 6A STAFF
(S)B-10.1
(S)O-1.2
S-5
F123
S-19
S-19
S-19
S-19
S-19
DN
S-19
DIV 6A ESTO
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)D-11.1
S-5
S-5
S-5
S-5
(S)O-1.6
(S)O-1.6
(S)O-1.6
(S)O-1.6
(S)F-3.1
F124
S-19
S-19
S-19
S-19
(S)O-1.8
BODY ROUTING OFF PUBLIC FILMS OFF
(S)P-1
(S)P-1
(S)P-1
(S)P-1
ADMIN STATION ADMIN STATION
LFN-401
LFN-400
S-19
S-19
S-19
(S)F-3.1
S-19
DIV 6A EXECS
S-9
F121 DN
(S)D-11.1
STAIR 2 STAIR 9
S-5
2 9
S-19
S-19
S-19
S-19
UP
(S)P-1
(S)D-3.1a
BF
UP
B-3.4 B-3.4
RESTROOM
F118 HFN-325
DV6-402 ; TYP
B-3.4
WTR-502.2
DV6-401 ; TYP RST-700 HFN-324
HFN-322
B-3.4
3
B-3.4
B-3.4
S-
S-
3
HFN-323
LEGEND
B-4.4
T-
6
ISSUE DATE DESCRIPTION BY CK
WTR-502.2
S-
3 ELECTRICAL
B-3.4
S-
CRIMINON APS
B-3.4
B-3.4
CCHR HR
3
F119 06.11.2010 SCHEMATIC DESIGN CS JA/ES
RST-700
07.09.2010 75% CONSTRUCTION CS JA/ES
RESTROOM DOCUMENTATION
F117 07.30.2010 PERMIT AND CONSTRUCTION CS JA/ES
DV6-303 ; TYP RST-800 MILLWORK, REFER TO SPACE PLAN
PUBLIC
NARCONON TWITH 3
S- BOOKSTORE
S-
B-4.4
CAB-2.1 F-3.1
3
VM ANTI-DRUGS HFN-323 F120
T- CUSTOM FURNITURE
6
HFN-400 WTR-502.2
S-5
3
S-
S-
3
SYSTEMS FURNITURE
DIV 6 DISPLAYS P-1
DN
F116
PURCHASED FURNITURE
DV6-323 DV6-323 DV6-323 DV6-323 DV6-323 DV6-323
HFN-303 STAIR 10
10
B-11.4 B-11.4 B-11.4 B-11.4 B-11.4 B-11.4 DN
B-11.4 B-11.4 B-11.4 B-11.4 B-11.4 B-11.4
AF
DN
3 CAB-2.1 B-10.1
S-
S-
3
T-
6
SMI/
SCIENTOLOGY I HELP S-5 MFN-313
3
S-
S-
PURIF SCIENTOLOGY
3
AROUND THE
WORLD TESTING I/C
UP
B-10.1 TESTING VESTIBULE Seal/Signature
MFN-400 F125 F126
KEY PLAN
SEE A THOUGHT DIANETICS
S-
3 MFN-317 ; TYP
S-
3
MFN-404 ; TYP
TESTING
IAS WISE T-
6
3
S-
S-
T-9
T-9
T-9
S-8
S-8
S-8
3
T-9
T-9
T-9
S-8
S-8
S-8
Project Name
STAIR 4 CLASS V ORG - TAMPA
4
T-9
T-9
T-9
S-8
S-8
S-8
Project Number
13.7042.430
(S)CAB-2
MFN-400 MFN-401
(S)D-11.1
1 / A06.11.A
(S)D-8.1g
Description
A B
S-5
S-2
REGISTRATION WTR-502.2
FURNITURE PLAN - FACTORY LEVEL 01 EAST
(S)F-3.1
DN F127
PLANTER
METER
TEST MARKING CHECK MFN-302
STAIR 7 MATCHLINE MATCHLINE Scale
7
TEST EVALUATOR
1/4" = 1'-0"
4 / A06.10.B T-5 4 / A06.10.B
C
S-2
S-2
S-16
Ref. North
8F 9F 10F 11F 12F 13F 14F 15F
A06.11.B
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:28 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
CHURCH OF
SCIENTOLOGY
1 / A06.12.B
MATCHLINE
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
SHEET NOTES
ROOF BELOW A00.00
WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.2 WTR-502.5 WTR-502.5 WTR-502.5
LFN-401
BF
(S)P-1
(S)P-1
(S)B-10.3 (S)B-10.3
(S)B-10.3 (S)B-10.3
FLAG BANKING OFFICER
(S)CAB-16.3
LFN-400 LFN-400
(S)CAB-15.1
FLAG REP P-1M P-1M
(S)B-10.1
S-9
(S)CAB-2
(S)F-3.1
(S)F-3.1
(S)B-5.5
(S)B-5.5
(S)D-3.1b (S)D-3.1b
(S)F-3.5
(S)F-3.5
(S)D-11.1
(S)D-11.1
(S)D-3.1d
F204
(S)D-8.1f
(S)D-8.1f
(S)D-8.2g
(S)D-8.2g
(S)P-1
(S)P-1
(S)B-10.1
(S)O-1.7
S-5 PES O/O
S-5
S-5
LFN-400 S-5
S-5
WTR-502.4
S-5
S-9
(S)D-8.2g
(S)D-8.2g
(S)D-11.1 S-5
(S)CAB-2
P-1M
(S)CAB-15.1
(S)CAB-2
S-5
S-5
P-1M (S)D-11.1
FINANCE (S)D-11.1
(S)B-5.5
(S)B-5.5
P-1M
(S)F-3.5
(S)F-3.5
(S)F-3.1
(S)F-3.1
F201
(S)CAB-2
(S)CAB-2
LFN-400 LFN-401
(S)CAB-15.1
(S)F-3.1
(S)F-3.1
LEGEND
(S)D-8.1g
(S)D-8.1g
ROOF BELOW P-1M O/O HES ED FDN ED DAY
(S)D-8.2g
(S)D-8.2g
OES
(S)D-11.1
S-9 LRH COMM F212 F216 ISSUE DATE DESCRIPTION BY CK
S-9
(S)F-3.1
F205
(S)F-3.1
S-9
(S)B-5.5
(S)B-5.5
LFN-400 ; TYP
S-5
(S)F-3.5
(S)F-3.5
S-5
(S)D-8.2g
(S)D-8.2g
O/O
(S)B-10.1
WTR-502.4 S-5
(S)P-1
(S)P-1
LFN-400 EQP-900 LFN-401
LFN-401 LFN-401 07.09.2010 75% CONSTRUCTION CS JA/ES
S-5
S-5
DOCUMENTATION
(S)P-1
(S)P-1
D/FBO MORE MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION CS JA/ES
LFN-325
S-5
(S)D-11.1
VESTIBULE
(S)F-3.1
(S)F-3.1
S-5
EXECUTIVE ESTO
CC-900 ; TYP
(S)F-3.1
(S)F-3.1
FSM I/C
F214 MEMBERSHIP
(S)F-3.1
S-2
WTR-502.4 MFN-401
ESTO NETWORK MFN-600
F202 MFN-600
T-5
(S)P-1
T-5
S-5
S-3
ESTO I/C WOMEN'S
(S)D-8.1l
F206 T-6
MFN-404 MFN-404
S-5
WTR-502.4 FSM/VM
(S)O-1.7
S-5
KITCHENETTE
F210
(S)F-3.1
ESTO I/C
3,4,5,
F203
S-8 S-8
RST-701 RST-701 Seal/Signature
KEY PLAN
(S)D-8.1f
S-5
(S)F-3.1
(S)O-1.2
(S)D-8.1h
ESTO I/C
6A,6B,6C
CLASSIC
WTR-502.2 EVENTS
F211
(S)CAB-2
MFN-407 ; TYP
SUCCESS DIR CLEARING
F215 F224
S-3
(S)F-3.1
MFN-401 MFN-400
S-3
(S)P-1
CORRIDOR
S-2
STAIR 1 MFN-401
F208
T-6
MFN-304
S-2
S-5
1 Project Name
S-3
(S)D-11.1
(S)D-11.1
CLASS V ORG - TAMPA
(S)B-5.8
S-3
(S)D-3.1c (S)D-3.1a
S-2
MFN-401
UP (S)P-1
S-3
Project Number
13.7042.430
Scale
1/4" = 1'-0"
C
1F 2F 3F 4F 5F 6F 7F 8F Ref. North
A06.12.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:28 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
CHURCH OF
SCIENTOLOGY
MATCHLINE
1 / A06.12.A
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
SHEET NOTES
A00.00
ROOF BELOW
LFN-401
BF
(S)F-3.1 (S)F-3.1
(S)CAB-16.3
P-1M
(S)CAB-9.2
(S)B-5.2
CC-5 CC-5 CC-5 CC-5 CC-5 CC-5
LFN-403 ; TYP
S-9
(S)O-4.7
RESEARCH OFF
(S)B-10.1
S-6 S-6 S-6 WTR-502.4
S-5
S-9
S-5
(S)CAB-8
(S)CAB-20.1
ELECTRICAL
F228
LFN-400 LFN-401
S-6
(S)T-8.2 (S)P-1
S-6
(S)CAB-9.1 (S)CAB-9.1
(S)D-11.1
LEGEND
(S)D-8.1g
(S)B-10.1
S-5
MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION CS JA/ES
EXEC CONF RM
F218 DN
UP
(S)F-3.1
STAIR 2
(S)F-3.1
CUSTOM FURNITURE
2
WTR-502.4
(S)CAB-2
DSA STAFF
F231 SYSTEMS FURNITURE
(S)D-3.1a
(S)CAB-2 P-1M (S)CAB-2 P-1M (S)P-1 (S)CAB-2
(S)B-5.1 (S)B-5.1 (S)B-10.2 LOBBY
(S)D-3.1h (S)D-3.1h (S)D-3.1g
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)F-3.1
F229
VESTIBULE
MFN-400 PURCHASED FURNITURE
S-5
MFN-401
S-5
S-9
S-2
F230
S -5
S-5
(S)F-3.1
(S)F-3.1
CC-5 CC-5
CC-900 ; TYP
MEMBERSHIP OT OPS
(S)B-10.1
MFN-400 MFN-308 T-5
SOCIAL
REFORM OFF
F219 F220 DIR PR LFN-400 LFN-401 S-5
MFN-400
F221 AF
S-2
S-2
S-2
MFN-401
(S)F-3.1
MFN-401 DIV 6C ESTO
S-2
(S)F-3.4
CC-5 CC-5 CC-5 CC-5 CC-5 CC-5 CC-5 CC-5 CC-5
DSA (S)P-1
(S)D-11.1
(S)D-11.1
F232
(S)D-11.1
DIV 6C STAFF
(S)F-3.1
(S)D-11.1
S-5
S-5
(S)CAB-2
MFN-400 ; TYP LFN-400 LFN-401 (S)P-1
DIR EXTENSION DIR EXTENSION COURSES
COURSES ASSISTANT
(S)F-3.1
S-9
LFN-400 ; TYP
(S)F-3.1
(S)B-10.1
DIV 6B S-5
S-5
(S)B-5.1
(S)D-11.1
S-5
S-5
S-5
S-5
S-5
S-5
MFN-400 PUBLIC
(S)O-1.8
S-5
S-5
S-5
S-5
S-5
S-9
F-2
S-5
(S)D-3.1d
(S)F-3.2 (S)P-1
MFN-401 S-2 (S)P-1 (S)B-10.1 (S)B-10.1
KEY PLAN
(S)D-11.1
(S)D-11.1
(S)D-11.1
EXTENSION
S-5
COURSES ADMIN
LFN-400 ; TYP
S-9
LFN-401
S-5
S-5
S-5
WTR-502.4
(S)P-1
(S)CAB-15.1 (S)CAB-2 (S)F-3.1 (S)CAB-15.1 (S)CAB-2 (S)F-3.1 HDF DIR
(S)F-3.1
(S)P-1
(S)P-1
(S)P-1
(S)P-1
(S)P-1
(S)P-1
SERVICES
S-2
(S)P-1
(S)P-1
(S)P-1
(S)P-1
(S)P-1
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)D-11.1
(S)D-11.1
S-5
(S)D-11.1
(S)D-11.1
WTR-502.4
S-5
S-5
CLASS V ORG - TAMPA
(S)D-11.4
(S)D-11.4
(S)D-11.4
(S)D-11.4
(S)D-11.4
(S)D-11.4
S-5
S-5
S-5
S-5
(S)B-5.8
(S)D-3.1a
S-2
S-5
S-5
S-5
S-5
S-5
S-5
WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4 WTR-502.4
Description
A B FURNITURE PLAN - FACTORY LEVEL 02 EAST
Scale
1/4" = 1'-0"
C
8F 9F 10F 11F 12F 13F 14F 15F Ref. North
A06.12.B
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:29 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
CHURCH OF
SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
SHEET NOTES
A00.00
MATCHLINE
1 / A06.13.B
WTR-500.4 WTR-500.4 WTR-500.4 WTR-500.4 WTR-500.4 WTR-500.4 WTR-500.4 WTR-500.4 WTR-502.7 WTR-502.6 WTR-502.6 WTR-502.6
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
RST-700
S-10
S-10
S-10
S-10
SUPERVISOR
CAB-15.5
T-7
T-7
(S)P-1 D-11.1
T-14.2
T-14.2
S-10
MFN-411
S-5
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
B-11.4
WTR-500.3
S-10
S-10
S-10
S-10
MFN-411 ; TYP RST-700
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
B-11.3
DIANETICS DIANETICS
SEMINAR/ SEMINAR/ CRM-400 CRM-300.1 CRM-401 ; TYP
LOC COURSE
B-11.4
CO-AUDIT CO-AUDIT RM
F301 LOC COURSE CRM-306.2; TYP
F-4.3
F302
CRM-323
RM
F308
F308
6B.17B.12 LEGEND ISSUE DATE DESCRIPTION BY CK
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
B-11.4
S-10
S-10
S-10
S-10
WTR-500.3 06.11.2010 SCHEMATIC DESIGN CS JA/ES
07.09.2010 75% CONSTRUCTION CS JA/ES
T-14.2
T-14.2
MFN-323 MFN-323
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
DOCUMENTATION
MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION CS JA/ES
S-10
S-10
S-10
S-10
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
S-19
B-11.4 B-11.4
(S)F-3.3
(S)F-3.3
B-9
CRM-322 CRM-400
CRM-321
B
CRM-307 WORD CLEARER
S-5 CRM-400 S-5 PUBLIC THEORY
(S)F-3.3
(S)F-3.3
B-11.4
(S)F-3.3
FILES CRM-400
S-10 S-10 S-10 S-10 S-10 S-10
F304 STCC COURSE
RM
WTR-502.6 S-10 S-10 SUPERVISOR
S-10 S-10 S-10
F309 S-10 S-10 S-10 CRM-401 ; TYP
B-11.4
T-14.3 T-14.3
S-10 S-10 S-10 S-10 S-10 S-10
D-11.1
ADMIN
S-5
S-5 MFN-409 F306
KEY PLAN
CAB-15.6
S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 T-1.3 T-1.3
CRM-301.3; TYP
(S)P-1
CAB-2.1 P-1 S-10 S-10 S-10
WTR-502.1 S-10 S-10 S-10
S-10
B-11.4
S-10 S-10 S-10 S-10 S-10 S-10
DN WORD CLEARER
S-10 S-10 S-10 S-10 S-10 S-10
MFN-314 CRM-400
B-11.4
S-10 S-10 S-10 S-10 S-10 S-10
T-1.3 T-1.3
Project Name
D-11.1
S-10
CLASS V ORG - TAMPA
S-5
MFN-412
S-10 S-10 S-10 S-10 S-10 S-10
DN
S-10 S-10 S-10 S-10 S-10 S-10
S-16
Project Number
13.7042.430
Scale
1/4" = 1'-0"
C
1F 2F 3F 4F 5F 6F 7F 8F Ref. North
A06.13.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:30 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
CHURCH OF
SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
SHEET NOTES
A00.00
B-9
B-11.4
RST-700 CRM-307
CRM-401 ; TYP CRM-321
B-11.2
B-11.4
T-10 CRM-305
CRM-327 DN WTR-502.6
S-10
RESTROOM
B-11.4
CRM-324 CRM-321
F312 JANITOR WOMEN'S S-10 S-10 S-10
CLOSET
F313
RESTROOM
F314
HAS TRS
F315
S-10 S-10 S-10 S-10 S-10
LEGEND ISSUE DATE DESCRIPTION BY CK
T-10 CRM-305 HQS PRACTICAL
B-11.4
F316
S-10
DN
SYSTEMS FURNITURE
ELECTRICAL
F104C TEL
F104D
CRM-307 CRM-321
PURCHASED FURNITURE
UP
STAIR 2
11
AF
B-9 WTR-502.6
B-9
T-13
CRM-302.3B B-11.4
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-14
T-1.2
T-1.2
T-1.2
T-3.2
S-10
S-10
S-10
T-2.3B
S-10
S-10
S-10
S-10
F311 CRM-303.2
S-14
CRM-900 CRM-307
B-11.3
6B.17B.06
CRM-305 T-10
HQS CO-AUDIT CRM-328
F318
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CAB-15.2
S-14
T-1.2
T-1.2
T-1.2
T-3.2
CRM-302.3B
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CRM-303.2 SUPERVISOR
S-14
CRM-300.1
D-11.1 (S)P-1
PUBLIC THEORY S-10 S-10 Seal/Signature
D-11.1
CRM-402 ; TYP
F311
T-2.3B
CRM-301.2; TYP
S-5
B-11.3
CRM-326
KEY PLAN
S-10
S-5
CRM-305
(S)P-1
PW-1
T-10
CRM-401 ; TYP
CRM-329 ; TYP
S-14
WTR-502.6
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
T-1.2
T-1.2
T-3.2
WORD CLEARER
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-14
CRM-303.2
S-10 S-10 S-10 S-10
B-11.3
CRM-300.1
T-2.3B
CRM-328
S-14
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CRM-305
Project Name
D-11.1
T-10 WTR-502.6
CAB-15.5
S-10
T-1.2
T-1.2
T-1.2
T-3.2
PW-1
S-14
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
Project Number
13.7042.430
WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6 WTR-502.6
1 / A06.13.A
Description
A B FURNITURE PLAN - FACTORY LEVEL 03 EAST
Scale
1/4" = 1'-0"
C
8F 9F 10F 11F 12F 13F 14F 15F Ref. North
A06.13.B
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:30 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
A. FURNITURE DRAWING NOTES CHURCH OF
B.
C. SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
ELEVATOR
STAIR UP
3
3
SHEET NOTES
MATCHLINE
1 / A06.21.B
A00.00
10S
(S)B-10.1
(S)B-10.1
DIR ROUTING & HCO ESTO
(S)O-1.5
PERSONNEL
(S)B-10.1
S-5 S-5 LFN-400
(S)B-6.1
(S)B-10.1
(S)B-10.1
LFN-400 R
S-5 LFN-400 S-5
S-5 S-5
(S)D-8.2l
(S)CAB-15.1
(S)P-1 (S)P-1
UTILITY
(S)B-6.1
RST-700 RST-700 S103 (S)D-11.1 (S)D-11.1 D-6
(S)P-1 (S)P-1 (S)P-1
(S)O-1.5
(S)D-11.1 (S)D-11.1 (S)D-11.1
(S)P-1 (S)P-1
(S)D-11.1 (S)D-11.1 HCO AREA SEC HCO COPE S-9 LFN-401
S-2
S-9 S-9 F
(S)B-6.1
S-9 S-9
S114 S115
(S)B-10.1
(S)B-10.1
PERSONNEL HCO CF OFF
(S)D-3.1h
S-5 S-5 HATTING
CONTROL OFFICER
OFFICER
LFN-401 LFN-401 S116
(S)O-1.5
CC-5 CC-5 CC-5 CC-5 CC-5 CC-5 CC-5 CC-5 CC-5
ROUTING & LFN-401 LFN-401 LFN-325
(S)B-5.1
DIRECTOR OF PERSONNEL
CC-900 ; TYPCOMMUNICATIONS LFN-400 ; TYP S109
(S)B-5.2 (S)B-5.2 (S)B-5.2 (S)B-5.2 CAB-3
MEN'S B-5.4
S108
UP WOMEN'S RESTROOM
(S)CAB-1.2 (S)CAB-8
S101 CC-900 ; TYP CC-5 CC-5 CC-5 CC-5 CC-5 CC-5
(S)D-8.1e
STAIR 1
1
MED RST-701 RST-701
HDF-900
MECHANICAL
S104
LEGEND ISSUE DATE DESCRIPTION BY CK
ETHICS
OFFICER
BS
(S)CAB-5 (S)CAB-2 06.11.2010 SCHEMATIC DESIGN AH JA/ES
LFN-400 S119
LFN-401 07.09.2010 75% CONSTRUCTION AH JA/ES
CC-900 ; TYP DOCUMENTATION
S-5 S-2 MFN-401 07.30.2010 PERMIT AND CONSTRUCTION AH JA/ES
LFN-401 F MILLWORK, REFER TO SPACE PLAN
S-9 S-9
S-2
DIR COMM CHIEF ETHICS
(S)O-4.4(S)P-1 (S)O-4.6 (S)O-4.6 INSPECT & OFFICER
REPORTS (S)P-1 S118
(S)D-8.1d D-6 D-6s
S117 CUSTOM FURNITURE
MFN-311.1L
(S)D-11.1 (S)D-11.1
(S)O-1.7
(S)O-1.7
(S)P-1
(S)P-1
INSPECTIONOFF DIR I&R
CORRIDOR S-5
(S)D-3.1a
(S)D-3.1a
S105 S-5 S-5 MFN-400
L L S-5
CORRIDOR LFN-400 LFN-400 MFN-324
SYSTEMS FURNITURE
S110
DN (S)B-5.1 (S)F-3.1
B-5.3 F-3.3 F-3.3
LFN-401 B-5.2 B-5.2
PURCHASED FURNITURE
(S)O-1.4 (S)O-1.4 (S)O-1.4 (S)O-1.4 (S)O-1.7
(S)P-1
(S)D-8.1a
(S)P-1 (S)P-1 AB
(S)CAB-2 (S)D-3.1a (S)D-3.1a -14
(S)D-11.1
(S)D-11.1
LFN-400 .1
S-5
(S)D-8.2l (S)D-8.2l
(S
)C
AB
S-5
(S
S-9
-14
)
S-9
S-5 S-5
B-
CF
LFN-400 ; TYP REGISTER MAIL I/C
CC-900 ; TYP .1
5.1
OFF
CC
(S
-5
) B-
C
DIRECTOR
5C
HDF-900 REGISTRATION
5
S111
S107
IT SERVER
AS
(S)B-5.2 (S)B-5.2 ROOM
PROMO & MKTG S121
S113
(S)F-3.1
WTR-502.3
CENTRAL FILES
S106 ALL-HANDS / CALL IN STATIONS
(S)F-3.1
S-5 S-5 S-5
(S)B-10.1
(S)F-5 PROMO
Seal/Signature
(S)P-1
(S)B-10.1
(S)CAB-14.1 (S)CAB-14.1
ASSEMBLY
(S)CAB-9.1
PHOTOGRAPHER DIR RAM
LFN-400 LINE OFF S-5
(S)O-2.3(S)P-1
(S)D-11.2
(S)O-2.3(S)P-1
(S)D-11.2
(S)O-2.3(S)P-1
(S)D-11.2
S-5 PROMO PRINT &
STG
(S)D-11.3
KEY PLAN
S-5
(S)O-1.8
(S)O-1.8
S122
S-5
(S)D-8.2l
(S)P-1 (S)P-1 (S)P-1 (S)P-1
(S)O-4.5
(S)D-11.2 (S)D-11.2 (S)D-11.2 (S)D-11.3
(S)P-1 (S)CAB-2
(S)D-11.1
(S)P-1 (S)P-1
DISSEM EXECS
S-5 S-5 S-5 S112
(S)D-8.1c
(S)O-1.3
(S)P-1
(S)B-10.1
WTR-502.3 DISSEMINATION S-5
SECRETARY (S)D-11.1 DIRECTOR OF MARKETING
BOOK PROMO & OFF
MARKETING LFN-400
5
BUYER
S-
S-
S-
ADDO LETTER LETTER LETTER LETTER ASR ASR DIR
(S)B-10.1
(S)P-1
(S)O-2.3(S)P-1
(S)P-1
(S)O-2.3(S)P-1
(S)P-1
(S)O-2.3(S)P-1
(S)P-1
(S)O-2.3(S)P-1
(S)P-1
5
LETTER
(S)O-1.8
(S)O-1.8
I/C REG REG REG REG I/C I/C REG S-5
LFN-400
(S)O-4.5
REG
(S
(S)D-8.2f
Project Name
) D-
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)D-11.2
(S)CAB-9.3
(S)O-2.3
(S)O-2.3
(S)O-2.3
(S)O-2.3
(S)O-2.3
(S
8.1
8.1
E-5
EQP-900
)
(S)O-1.3
D-
a
D-
CLASS V ORG - TAMPA
8.1
)
(S
b
S-5
S-5
S-5
S-5
S-5
S-5
S-5
S-5
S-5
Project Number
13.7042.430
A B
Description
MATCHLINE
1 / A06.21.B
FURNITURE PLAN - STEMMERY LEVEL 01 WEST
Scale
1/4" = 1'-0"
1S 2S 3S 4S 5S 6S 7S 8S 9S
Ref. North
A06.21.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:31 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
A. FURNITURE DRAWING NOTES CHURCH OF
B.
C. SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
ELEVATOR
2 STAIR 2 UP
MED 2
UP
CORRIDOR TO
FACTORY
101 Marietta Street NW
Suite 3000
SHEET NOTES
MATCHLINE
MATCHLINE
1 / A06.21.A
A00.00
MFN-310.1B MFN-310.1C
S-10
S-10
S123
(S)B-6.1
S129
T-12.2
R MFN-304
S-5 S-5 MFN-400
MFN-334
S-10
S-10
MFN-400
B
MFN-400
C
B
MFN-400
S-
5
5
T-6
S-
S-
5
(S)B-6.1
D-6
(S)P-1
CAB-11.1
(S)O-1.5
P-1
(S)D-11.1
REGISTRATION
ETHICS WORK BRSO ELECTRICAL
S-2 S130 REGISTRATION REGISTRATION
S-9
F MFN-401 AREA S134
UP UP
(S)B-6.1
S131 S132
S124
B-10.4
S-3
S-
S-3
MFN-314
(S)D-3.1h
5
HATTING
OFFICER
S116
(S)O-1.5
CAB-15.1
MFN-325
(S)B-5.1
MFN-326
CAB-2.1
MFN-407 MFN-407 MFN-409
MFN-413 MFN-413 MFN-413
B-11.2 MFN-406
CAB-3 CAB-15.5
B-5.4 B-5.4
S-16
HCO
RECEPTION
S125
UP
ETHICS BS
LEGEND ISSUE DATE DESCRIPTION BY CK
P-1 CAB-2.1
OFFICER
S119 06.11.2010 SCHEMATIC DESIGN AH JA/ES
(S)B-5.4
S-3
S-3
S-3
S-3
S-2
D-6s
B-5.4
MFN-308 T-5
T-6.4
T-6.4
(S)D-11.5
T-5 MFN-308
S-
S-5
MFN-400
B-5.4
S127
MFN-401 SYSTEMS FURNITURE
S-2
MFN-327
BREAK ROOM
F-3.3 F-3.3 (S)F-3.1 (S)F-4.3 (S)F-4.3 (S)F-4.3 (S)F-4.3 S-3
S-3
S-3
S-3
PURCHASED FURNITURE
MFN-414 ; TYP MFN-307 MFN-307
CORRIDOR
S120 DIV 2
BOOKSTORE
S133
(S)O-1.2
CC-5 CC-5 CC-5 CC-5 CC-5 CC-5
(S)P-1
IT SERVER
(S)CAB-15.1
(S)D-8.2k AS
ROOM CC-900 ; TYP CASHIER
(S)CAB-2
S121 S-5
MFN-315 PUBLIC CONF
WTR-502.3
(S)F-3.1
HDF-900 RM
B-3.4
B-3.4
B-3.4
B-3.4
B-5.4
B-3.4
B-3.4
B-3.4
B-3.4
MFN-400 S136
MFN-329 ; TYP MFN-328
B-11.4
TREASURY MFN-403 ; TYP S-6 S-6 S-6
S128
(S)F-3.1
B-3.4
B-3.4
B-3.4
B-3.4
B-5.4
B-3.4
B-3.4
B-3.4
B-3.4
P-1 P-1
(S)B-10.1
S-6
S-6
LFN-400 ; TYP
(S)T-8.3 Seal/Signature
CAB-20.2
(S)CAB-9.1
KEY PLAN
(S)B-10.1
S-5
DIR INCOME
BSO MFN-409
(S)D-11.3 MFN-332
S-6
S-6
S-5 MFN-330
(S)O-4.3 (S)O-4.3 (S)P-1
(S)F-3.1
B-11.4
(S)P-1
S-6
S-6
(S)P-1
(S)F-3.1
B-3.4
B-3.4
B-3.4
B-5.4
B-3.4
B-3.4
B-3.4
CAB-10 B-3.4
(S)P-1 B-3.2 B-3.2
(S)B-10.1
TREASURY MFN-331
S-5
(S)O-4.5
SECRETARY
B-3.4
B-3.4
B-3.4
B-3.4
B-5.4
B-3.4
B-3.4
B-3.4
B-3.4
Project Name
E-5
EQP-900 MFN-333
CLASS V ORG - TAMPA
(S)F-3.4 (S)F-3.4 (S)CAB-15.1 (S)CAB-2 (S)B-5.4 (S)F-3.4 (S)F-3.4
B-11.4 B-11.4 B-11.4 B-11.4
Project Number
13.7042.430
Scale
1/4" = 1'-0"
10S 11S 12S 13S 14S 15S 16S 17S 18S 19S
Ref. North
A06.21.B
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:33 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
A. FURNITURE DRAWING NOTES CHURCH OF
B.
C. SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
DN DN
ELEV STAIR
3 3
101 Marietta Street NW
Suite 3000
SHEET NOTES
MATCHLINE
1 / A06.22.B
A00.00
WTR-502.3 WTR-502.3
CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4
LFN-301 D-4 PUR-901 ; TYP
PUR-400
S-3
ARM
S-5
DN LFN-406 LFN-324
BERTHING S-16
S208
S-3
RST-700 RST-700 WOMEN'S
ELECTRICAL WOMEN'S
LFN-322 CHANGING
S205 SAUNA
ROOM
S215
S212
S-3
DRESS
CHEST
ARM
LFN-323 LFN-324
S-3
WOMEN'S MEN'S LFN-321A PUR-800 PUR-800
RESTROOM RESTROOM LFN-321B
S201 RST-700 S203 RST-700 RST-700
LFN-500 CORRIDOR
S213
LFN-600 LFN-600
CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4CAB-4
LFN-405 S-18 LAUNDRY ROOM PUR-800 PUR-800
S211 MEN'S MEN'S SAUNA
CHANGING S216 CUSTOM FURNITURE
RST-800 ROOM
ROOF BELOW S214
PUR-400
SYSTEMS FURNITURE
S-16
(S)B-1.1 AUD-401
AUD-401 AUD-401 AUD-401 AUD-401 AUD-401 AUD-401
S-13 S-13 S-13 S-13 S-13 AUD-401 S-13 S-13 S-13
F AUDITING RM AUDITING RM F F AUDITING RM AUDITING RM F F AUDITING RM AUDITING RM F F AUDITING RM AUDITING RM F F
R
(S)B-1.1
S-12 AUD-400 S221 S223 S225 S227 S229 S231 S233 S235
AUDITING
SUPPLIES
S217
D-6 AUD-300.1RF
D-6
AUD-300.1LF
D-6 D-6 D-6 D-6 D-6 D-6
AUD-300.1LF
D-6 D-6
AS
(S)B-1.1
Seal/Signature
R S-12
AUD-400
KEY PLAN
AUD-300.1RF
D-6
AUDITING RM L R L R AUD-400 L R L R L R
AUD-400 S-12 S-12
AUD-400 AUD-400 S-12 S-12 AUD-400 S-12 S-12 AUD-400 AUD-400 S-12 S-12 AUD-400 AUD-400 S-12
S219
S-13
F
WTR-502.3 AUD-401
AUD-300.1RF AUD-300.1LF AUD-300.1LF
AUD-300.1LF AUD-300.1RF
D-6 D-6 D-6 D-6 D-6 D-6 AUD-300.1RF AUD-300.1LF D-6 D-6 D-6 D-6
AUD-300.1RF AUD-300.1LF AUDITING RM AUDITING RM AUDITING RM
AUDITING RM
AUD-900 S226 S228 S236
AUDITING RM AUDITING RM S234
AUDITING RM AUDITING RM AUDITING RM Project Name
S230 S232
S220 S222 S224
S-13 F F S-13 S-13 F F S-13 S-13 F F S-13 AUD-401 S-13 F F S-13
AUD-401 S-13 F F CLASS V ORG - TAMPA
T-13
Project Number
13.7042.430
WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 A B
MATCHLINE
1 / A06.22.B
FURNITURE PLAN - STEMMERY LEVEL 02 WEST
Scale
1/4" = 1'-0"
1S 2S 3S 4S 5S 6S 7S 8S 9S 10S
Ref. North
A06.22.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:36 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
A. FURNITURE DRAWING NOTES CHURCH OF
B.
C. SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
ELEVATOR
2 UP
MED
SHEET NOTES
MATCHLINE
MAINTENANCE
1 / A06.22.A
S270 A00.00
TECH CALL-IN DN
S244
WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3
(S)O-1.8 (S)P-1
E-5 (S)CAB-2 HGC-301
S-5
(S)B-5.1 (S)B-5.1 (S)B-5.1 (S)B-5.1 D-10.3
PUR-300
(S)B-7.2
(S)D-8.1j
(S)D-8.1h
(S)D-8.1h
S-5 S-5
(S)O-1.8
S-3
(S)P-1
STUDENT CASE
EQP-900
S-5
S-5 S-5 S-5
(S)B-10.1
S-7
(S)B-10.1
SUPERVISOR HGC-401
S-16
LEAD CASE
S-5 SUPERVISOR S-5 HGC
(S)B-7.2
(S)P-1
LFN-400 ; TYP
S-3
RECEPTION
S-5
WOMEN'S S267 WTR-502.3
(S)P-1
SAUNA S-5 S-5 S-5
(S)P-1 (S)P-1
S215 S-3 S-3
(S)P-1
CAB-15.3
S-3
(S)B-8.1
(S)B-8.1
(S)D-11.1 (S)D-11.1
(S)B-7.2
HGC-320
(S)D-8.2j
T-6
HGC ADMIN #1
S-16
PUR-400
(S)D-8.1h
(S)D-8.1h
(S)O-1.8
(S)O-1.8
(S)T-1.3
B-5.4
(S)P-1
HGC-402
S-5
S-3
(S)P-1 (S)P-1
S-5
(S)D-11.1 (S)D-11.1
(S)B-7.2
CAB-20.2
S-5 S-5 S-5
S-5
(S)P-1 (S)P-1
PURIFICATION CASE GRADES CASE
(S)B-10.1
(S)B-10.1
S-5 SUPERVISOR SUPERVISOR S-5
PUR-300
B-5.4
T-6
HGC-300 LFN-400 ; TYP
HGC WAITING
LFN-400 ; TYP TECH CASE
CC-1 CC-1 CC-1 CC-1 CC-1 CC-1
S266
SUPS
(S)B-7.2
CC-900 ; TYP S-5 S-5 S-5
S245
(S)B-10.1
PURIFICATION
(S)O-1.8
HGC-321
CAB-15.3
TECH CASE
B-5.4
(S)D-8.1i
(S)D-8.2j
S-5
SUPERVISOR
S238
S-5
S-5
OFFICER
S-3 S-3 WTR-502.3
(S)P-1
(S)P-1
(S)D-11.1
(S)B-8.1 (S)B-8.1 CC-901 ; TYP
S-5 S-5 S-5 LEGEND ISSUE DATE DESCRIPTION BY CK
BS
HGC AUDITOR 06.11.2010 SCHEMATIC DESIGN AH JA/ES
PUR-401 ; TYP HGC-400 HGC-400 07.09.2010 75% CONSTRUCTION AH JA/ES
ADMIN
S269 DOCUMENTATION
MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION AH JA/ES
LFN-400 ; TYP
S-14 S-14
B-11.3
B-11.3
S216 CUSTOM FURNITURE
R S-13 DTS
PUR-402
O-2.7
A
MFN-400 MFN-417 MFN-400 S-5
STAFF D OF P
B-11.3
B-11.3
MFN-338 MFN-401 MFN-310.1A
D-6 S257 WTR-502.3 SYSTEMS FURNITURE
D-6
S-14
D-6 MFN-400
S-
TECH ESTO
5
F-4.3
F-4.3
D-6
PURIF
S-3
PUR-402
S-5
S-2
(S)D-3.1a
S250
(S)O-1.2
IN-CHARGE
O-2.3
F
S246 O-2.7 O-2.3
MFN-336
(S)P-1 MFN-317 ; TYP S-5 S-5 S-5
AUD-401
S-13 S-13 (S)D-3.1a
(S)D-11.1
AUDITING RM
S-2
MFN-400 WTR-502.3
S-12 R L S-12
AUD-400 AUD-400 S-12 R L S-12 AUD-400 AUD-400 S-12 R L S-12 AUD-400
S-8 S-8
AUD-400 (S)D-8.1g DIV 4 TESTING
S-5
CORRIDOR Seal/Signature
S237
KEY PLAN
Project Number
13.7042.430
WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3 WTR-502.3
Scale
1/4" = 1'-0"
10S 11S 12S 13S 14S 15S 16S 17S 18S 19S
Ref. North
A06.22.B
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:39 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
A. FURNITURE DRAWING NOTES CHURCH OF
B.
C. SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
SHEET NOTES
MATCHLINE
1 / A06.23.B
A00.00
B-11.3 B-11.3
S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 CRM-401 ; TYP
S-10
S-10
S-10
S-10
S-10
S-10
S-10
T-1.2
T-1.2
CRM-333
B-11.4
DN
RST-700
S-10
S-10
S-10
S-10
S-10
S-10
S-10
RST-700 S-10 S-10 S-10 S-10 S-10 CRM-401 ; TYP S-10 S-10 S-10 S-10 S-10
ELECTRICAL
S304
PROFESSIONAL CRM-331
B-11.4
TRS & ACADEMY
TRS OBJECTIVES PRACTICAL
S309 S313 CRM-401 ; TYP S314 CRM-301.2; TYP
S-10 S-10 S-10 S-10 S-10
CRM-307
S-10 S-10 S-10 S-10 S-10
B-9
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CRM-307 B-9
S-10 S-10 S-10 S-10 S-10
TOLIET ROOM
T-1.2
T-1.2
S302
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10 S-10 S-10 S-10 S-10
WOMEN'S MEN'S
B-11.4
RESTROOM RESTROOM
DN STAIR 1 S301 S303 UPPER INDOC
1 TRS
S310 CRM-331
B-11.4
RST-701 RST-701 MECHANICAL
S305
LEGEND ISSUE DATE DESCRIPTION BY CK
BS
06.11.2010 SCHEMATIC DESIGN AH JA/ES
S-10
S-10
S-10
S-10
S-10
S-10
S-10
07.09.2010 75% CONSTRUCTION AH JA/ES
S-14
DOCUMENTATION
MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION AH JA/ES
T-3.3
T-3.3
T-1.3
T-1.3
S-10
S-10
S-10
S-10
S-10
S-10
T-2.3B
S-10
CRM-401 ; TYP
S-14
CUSTOM FURNITURE
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CAB-12 CRM-332 CRM-302.3B
S-14
PRO TRS VIDEO TR-8
S-10
S-10
ROOM S312 CRM-402 ; TYP
S311 CRM-401 ; TYP
CRM-303.3 CRM-303.3 CRM-301.3
SYSTEMS FURNITURE
F-4.3
CRM-334
S-10
S-10
S-10
ACADEMY
S-14
CRM-302.3B THEORY PURCHASED FURNITURE
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S316
04.11.04
T-2.3B
S-14
T-3.3
T-3.3
T-1.3
T-1.3
B-11.3
S-10
S-10
S-10
S-10
S-10
S-10
S-10
SUPERVISOR
CRM-400 S-5
S-14
CRM-333
B-11.3
S-10
S-10
S-10
S-10
S-10
S-10
S-10
(S)P-1 ACADEMY
D-11.1
CRM-300.1 CO-AUDIT
S-10
S307
AS
WTR-502.8 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10
CRM-330
CRM-304 CRM-401 ; TYP
F-4.4
CRM-331
S-10
S-10
S-10
S-10
T-4 T-4
S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10
CRM-300.1 CRM-400
F-4.4
Seal/Signature
KEY PLAN
S-10
S-10
S-10
S-10
B-11.4
B-11.4
CRM-331
CRM-331 CRM-401 ; TYP CO-AUDIT SUPERVISOR
(SEATED)
(S)P-1 D-11.1
S-10
S-5
S308
B-11.4
OBJECTIVES
B-11.4
04.11.09 CO-AUDIT
B-11.4
B-11.4
S-10
S-10
S-10
S-10
S-10
S-5
S318
SUPERVISOR
B-11.4
WTR-502.8
CAB-15.6
S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10
S-10
S-10
S-10
S-10
T-4 T-4
T-10
T-10
S-10
S-10
S-10
T-4 T-4
S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10 S-10
Project Number
13.7042.430
A B
Description
MATCHLINE
1 / A06.23.B
FURNITURE PLAN - STEMMERY LEVEL 03 WEST
Scale
1/4" = 1'-0"
1S 2S 3S 4S 5S 6S 7S 8S 9S 10S
Ref. North
A06.23.A
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:42 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt
DRAWING NOTES
A. FURNITURE DRAWING NOTES CHURCH OF
B.
C. SCIENTOLOGY
CLASS V ORG - TAMPA
1300 East 8th Ave
Tampa, FL 33605
ELEVATOR
2
DN
SHEET NOTES
MATCHLINE
1 / A06.23.A
A00.00
DN
WTR-502.8 WTR-502.8 WTR-502.8 WTR-502.8 WTR-502.8
S-10
S-10
S-10
S-10
S-10
S-10
S-10
(S)D-11.1
(S)D-11.1
S-10
S-5
(S)CAB-15.1
(S)P-1 D-11.1
T-1.2
T-1.2
T-1.2
T-1.2
(S)D-3.1a
B-11.4
S-2
S-5
S-13
(S)D-8.1l
S-5
(S)B-5.1
WORD CLEARER
CRM-300.1 MFN-400
COATS & S-5
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
STUDENT
STORAGE DIR TRAINING
CRM-400 CRAMMING WTR-502.8
(S)F-3.1
S319 S320
B-11.4
ACADEMY OFFICER DIR EXAMS
CRM-301.2; TYP PRACTICAL MFN-400 S334 MFN-417 MFN-401 S335 MFN-400
(S)F-3.1
(S)F-3.1
(S)D-11.1 HDF-900
S-10
S-5
CRM-301.2; TYP S314 CRM-401 ; TYP
(S)P-1 D-11.1
MFN-400
(S)D-3.1a
COURSE ADMIN
(S)O-1.8
SUPERVISOR MFN-401 S-2
CAB-7.2
S321
S-5
CRM-300.1 04.11.02
(S)F-3.1
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CRM-336
T-1.2
T-1.2
T-1.2
T-1.2
CAB-9.2
S-10
S-10
S-10
S-10
S-10
S-10
S-10
T-1.2 QLS-301.2
T-12.2 QLS-302.2
S-5
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-11
S-11
S-11
S-11
S-7 DOCUMENTATION
CAB-15.2
CRM-337 MILLWORK, REFER TO SPACE PLAN 07.30.2010 PERMIT AND CONSTRUCTION AH JA/ES
P-1
QLS-300 QLS-400
T-1.3
T-1.3
T-1.3
T-1.3
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CRM-300.1
S-11
S-11
S-11
S-11
S-10
MFN-312 D-4.1
WORD CLEARER
S-5
CUSTOM FURNITURE
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-11
S-11
S-11
S-11
(S)P-1 D-11.1
(S)O-4.5 (S)O-4.5
S-5
TECH VIDEO
ROOM DIR CERTS &
CRM-301.3 CRM-301.3 ACADEMY CRM-301.3 CRM-301.3 AWARDS
CRM-400 S322 WTR-502.8
THEORY QUAL ADMIN SYSTEMS FURNITURE
CC-900 ; TYP
S-11
CRM-301.3 CRM-301.3 S316 CRM-301.3 CRM-401 ; TYP CRM-301.3 S327
CRM-337
SUPERVISOR
(S)P-1 D-11.1
S-5
PURCHASED FURNITURE
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-10
S-11
S-11
S-11
S-11
FLM-400 ; TYP
(S)F-3.2(S)F-3.2(S)F-3.2(S)F-3.2
(S)B-5.1
(S)D-11.2
(S)D-3.1a MFN-417
T-1.3
T-1.3
T-1.3
T-1.3
S-2
F
S-11
S-11
S-11
S-11
S-10
S-10
S-10
S-10
S-10
S-10
S-10
CAB-15.5
S-13
S-10
S-5
MFN-401
(S)B-5.1
S-11
S-11
S-11
S-11
S-10
S-10
S-10
S-10
S-10
S-10
D-6
S-10
MFN-311.1RF
S328
AS
S-3
MFN-414 S-5
MFN-400 R
(S)O-1.7 (S)O-1.7
MFN-414
S-3
T-10
T-10
LFN-400
F-3.4O-1.6 B-5.4 CAB-15.3
SENIOR C/S O-1.6
Seal/Signature
(S)B-10.1
DEPUTY OFFICE
QUAL SEC
CRM-305 ; TYP
S-5
QUALIFICATIONS
S324
(S)B-5.1 KEY PLAN
E-5
(S)D-3.1a
(S)D-3.1d
LFN-400 CAB-7.1
(S)P-1
(S)O-1.7
S-5
(S)O-1.7
(S)P-1
B-11.4
(S)B-8.1
B-11.4
S330 S331
(S)F-3.1
(S)D-11.1 SSO
(S)P-1 (S)D-11.1 CRM-300.1A CRM-401 ; TYP
B-11.4
S329
(S)P-1
(S)P-1
(S)F-3.1
D-11.1 (S)P-1
QUAL SEC
(S)B-10.1
(S)P-1
S-5
(S)CAB-2
B-11.4
(S)D-3.1h
(S)D-3.1h
CRM-400
S-10
S-10
(S)D-11.1
(S)O-1.7
(S)O-1.8
T-1.2
(S)P-1
(S)D-3.1a
S-10
CLASS V ORG - TAMPA
S-5
(S)F-3.1
(S)F-3.1
S-5
LFN-400
T-10
T-10
S-10
S-10
TIC I/C
(S)B-5.1 (S)CAB-15.1 (S)F-3.1 (S)CAB-2 (S)CAB-15.1 (S)F-3.1 (S)B-5.1 A
Project Number
13.7042.430
Scale
1/4" = 1'-0"
10S 11S 12S 13S 14S 15S 16S 17S 18S 19S
Ref. North
A06.23.B
© 2010 Gensler
PLOTTING DATE: 8/5/2010 1:58:43 PM FILE PATH AND NAME: S:\13.7042.430\BIM\Building Model\_User Model Files\Tara Hudgins_137042430_Tampa.rvt