You are on page 1of 31
Hifi €NGINEé For more Hi-Fi manuals and set-up information please visit www.hifiengine.com AIWA-00133 8/M Code No. 83-006 AIWA’ care of SERVICE MANUAL MODEL NO. STEREO CASSETTE DECK AD-F'7 7 oO TYPE. H,HU,U,E,K,G Performance and give many years of serivce. ‘8c. primary circuit including mains leeds, 2. No illegibiity shall be given to the specification plate, the cau- tion labels, the fuse labels and others. 3. When, on pattern sides of circuit boards, additional repsir-parts hhave been made up, the parts shall be firmly glued to circuit boards or other components, unless the parts can be attached firmly. 4, The following mattars shall be maintained a they are, when repairing. 1) Soldering of leadwire ends *Care should be taken of the space distance in an a. pri- ‘mary circuit as well es soldering 2) Wiring and holding of lead-wires with wire-lips and binders 3) Materials of lead-wires ‘e.; For UL models, leadavires to be used shall be op- proved or accepted by the UL. 4) Location of all kinds of insulators 5) Setting of voltage selector switch *Set the Voltage Selector Switch to 240V, 220V, or 120V, According to your Locel Voltage. 5. After repaired, the insulation resistance or leakage current shall bbe measured with 500 + 5V D.C and shall be not less than 1M22. Measuring Point fatng More than 1/500 OC Pin Jaok(@3) “KO Power Ooal@) Follow the instructions carefully, which will allow the user to optimise the products’ 1, No soratch and melting shall be made to covered lead-wires of an 6. General instructions for mechsnism repair 1) The heads, capstan and pinch roller shall be cleaned of good uality alcohol after repeired, because dirty heads shall cause distorted sounds while dirty capstan and pinch roller shall occur wow/flutter and take-up fault, 2) Lubricants been stained the surfaces of transmitting portion of the belts, idlers, capstan and pinch roller shall be removed, because slippery and faulty tape travel shall be caused. 3) When ciling, only one or two drops shall be epplied #0 2 ‘ot to run over and be dispersed. Note should be taken of the metal fitting for the capstan and roteting portions of the Idlers and pinch roller, expecially, 4) E-rings and poly slider washers shall be replaced with new fones, if once those have been removed, — No re-utilization ‘due to unreliebilty Regular spere-parts shell always be used for repair, because Using irregular parts and tampering with the products shall cause deterioration, mulfunction and damage. 8) Connect 10 Chass or Oise G of Pin ok SPECIFICATIONS ‘Semiconductors: 371Cs, 91 transistors, 1 FET 87 diodes, 19 LED's Power supply: H, HU modais ‘AC 120v /220v/240v ‘switchable 50/60 Hz U model ‘AC 120V, 50/60 Hz E model ‘AC 220V, 60/60 Hz K, 6 modais "AC 240V, 60/60 Hz ower consumption: 330, Dimensions: 420tW) x 11014) x 280(0) mm (16—1/2" x 4-3/8" x 1-1/4") Weight: 5.5 kg (12.11 tbe) ‘Track type: 4 tracks 2 channels Tape speed: 4.8 cm/s (1718 ps) 2 1.5% Wow an flutter: 0.025% (WRMS) ‘According to DIN 45500 0.09% ‘Automatic stop system: Fi Pinch roller pressure: T side: 950 + 309 (3.43 + 0.20N) Sside: 165 + 159 (1.61 0.15N) Tekeup tra Se Mogem tage son mn) FF & rind tora: 180.40 90m (147 $938 mm) FF Grewind tis 602700 (60) Counter indication error: 0 + 3 digit (C-60) ‘Camstie lid action time: 0.8 + O.4s. (at normal temperature) Playback output: 540+ 60 mV {TTA-161) REC/PB output: 380 mv (27 kf, OVU) RECIPE distortion: Less than 1.9% (METAL) Less than 1.3% (Cr0,) ‘Less than 1.3% (NORMAL) Playback noi oss than 27 mV {Unweighted) (NORMAL DOLBY NR OFF) Less than 1.5 mv (NORMAL DOLBY NA 8) Less than 1.2 mV (NORMAL DOLBY NAc) Les than 2.0 mv (METAL, CrO,, DOLBY NR OFF) Less than 1.2m (METAL, CrO, , DOLBY NR 8) Low than 1.0 mV. (METAL, CrO, , DOLBY NRC) (wpa) Loss than 1.2 mV. (NORMAL DOLBY NR OFF) Less than 0.8 mV (NORMAL DOLBY NR B) Loss than 0.6 mV (NORMAL DOLBY NAC} Los than 7.0 mV? (METAL, Cr0,, DOLBY NR OFF) Less than 0.5 mV (METAL, CrO, , DOLBY NAB) Less than 0.5 mV (METAL, CrO;, DOLBY NRC) REC/PB SN ratio: (400 Hz, ovut (Unweighted) More than 44/47 JB (METAL, CrO,, DOLBY-NR B OFF/ON) More than 42/48 a6 (NORMAL, DOLBY.NR B OF F/ON) More than 44/49 dB (METAL, CO, , DOLBY-NR C OFF/ON) More than 42/48 0B (NORMAL, DOLBY.NF C OFF/ON) More than 48/57 68 (METAL, DOLBY-NR 8 OFF/ON) ‘More then 50/59 48 {CrO, , DOLBY-NR B OFF/ON) More'than 46/55 48 (NORMAL, DOLBY-NR B OFF/ON) More then 48/64 48 (METAL, DOLBY-NR C OF F/ON) More then 50/60 dB {CrO, ,DOLBY-NR C OF F/ON) More’ than 46/60 dB (NORMAL, DOLBY.NR C OFF/ON) ‘Channel separation: More than 30 dB (1 kHz, OVU) Cross tak: ‘More than 60 dB (kHz, ovU) Erasing ratio: ‘More than 60 d8 (126 Hz, OVU + 10 4B, METAL) Level drift: 20.508 (10 kHe) Level indication err (-20vu) + 548, (Ctovu) +398 ( -OVU) = 1 48 (2 ~ 46vU) +2 G8 ~ +10VU) + 248 ADMS time: 2.0 + 0.8s. (POWER ON) (ADMS LED light up tiene) Bias frequency: 85 kHz Frequency remonse: (0. dB Rec. DOLBY NRC ON) DOLBV-NR Effect: (10 kHz, CCIR FILTER) Motor: Heed: Inputs: Outputs: ‘Test tape: METAL: 20 ~ 20,000 Hz+ 3.48 =20 dB Rec.) 20 ~ 17,000 Hz + 348 (dB Rec.) CrO, + 20~ 19000 Hz + 3.48, {2048 Ree.) 20~ 14,000 Hz + 348 (OB Rec.) NORMAL : 20 ~ 18,000 Hz + 3.48 (20 48 Rec.) 20 ~ 11,000 Hz + 348 (oaB Rec.) More than 8 48 (DOLBY NR B-type) Mors then 1640 ILBY NR C-type) DC Servomotor for capstan DC motor for reels DX Combination head (tor REC/PB) Double gab semdust heed (for erase) MIC maximum input sensitivity: 0.3 mV (200 2 —10 kf matched) LINE IN maximum input Sensitivity: 50 mV (more than 60 k2) LINE OUT/PLAY standard ouput level: 0.38V (OVU); suitable load impedance: more than 60 ki; Headphones: 8.2. METAL TTA-119Mx NORMAL TTA.1193 CO, TTAN196 ion system manufactured under license from Dolby Laboratories Licensing Corporation. * Dolby end the OC symbol are trademarks of Dolby labo- ratories Licensing Corporation, ‘© HX professionel originated by BANG & OLFSEN. ‘As to the disassembling instructions, refer to the service manual of ‘AD-F660, ep

You might also like