Professional Documents
Culture Documents
CONTENT
604.55.061.00 - 01 - 2000
2 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1
1
There are two battery options.
Standard 1 x 1200 CCA
Cold start 2 x 900 CCA
604.55.061.00 - 01 - 2000
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1 3
3
For primary protection the main supplies from the
starter solenoid are fitted with maxi fuses.
These are located behind the left hand instrument
cluster console side panel.
4
There are two fuse links fitted:--
1. In the main battery to alternator lead.
5
2). In the 12v supply lead from the alternator B+
terminal to the starter relay (C005 pin 1
FM--150U--N)
604.55.061.00 - 01 - 2000
4 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1
7
Relay Function Relay Function
A Blank (Air Brakes - Germany/With Cab only) III Thermostart Relay
B Worklamp Relay -- Front (Roofline) IV Front Intermittant Wipe
C Worklamp Relay -- Rear (Roofline) V Blank
D Worklamp Relay -- Lower Front VI Rear Intermittant Wipe
E Worklamp Relay -- Lower Rear VII
F Bridge Link or Fuel Shut Off Relay VIII
} Front Hitch Control Module
G Stoplamp Relay IX Trailer Brake Relay
H Trailer Brake Relay X Blank
I Ignition Relay XI
II Hydraulic Diverter Valve Relay XII
} ISO Module or NASO Module (Indicators)
NOTE: Indicator relay is located separately behind
No. Amps. Circuit the MDP.
1 15 Headlamp -- Main
No. Amps. Circuit
2 15 Headlamp -- Dip
3 10 Sidelamp -- Right Hand 16 25 Heater Fan
4 10 Sidelamp -- Left Hand 17 20 Wiper Washer/Front Wiper/Rear Wiper/
Temperature Control/Console Lamp
5 30 Worklamp -- Front (Grill Mounted)
18 10 Turn Indicators
6 15 Worklamp -- Rear (Fenders)
19 25 Thermostart
7 15 Worklamp -- Front & Rear (Cab Roof)
20 5 Keep Alive Memory for Transmission and
8 15 Fuel Shut--Off/Fuel Pump/Water in Fuel EDC Processors, EMU and Radio, Supply
9 10 Gauges/External Switches/Radar for Diagnostic Connectors
10 20 Hazard Lights 21 25 Transmission Control Module/Clutch
11 10 Horn/Headlamp Flasher/Cigar Lighter/Roof Switch/Gear Shift Indicator/Limp Home
Beacon 22 5 Radio
12 10 EDC 23 23 Accessory Socket/Interior Lamp/Cigar
13 25 Diff Lock/PTO/4WD/Worklamps Lighter
14 10 Transmission Shuttle 24 30 Implement Socket
15 30 EMU Module/Stoplamps/Seat Pump/ Front 25 20 Stop Lamp relay (G) Supply
Hitch Trailer Brake/Diverter Valve NOTE: Fuse 25 is located in a separate holder
attached to the maxi fuses.
604.55.061.00 - 01 - 2000
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1 5
Micro Processors
The tractor can have a maximum of 4 processors
(including an Electronic Instrument Cluster, where
fitted). With 3 processors connected to the
instrument cluster by a serial link for cluster display.
Electronic Management Unit
8
Electronic Instrument Cluster
9
GCM
Dual Command
Transmission and EDC Control
Range Command
EDC and Suspended
Power Command
Suspended Front Axle Control
10
TCM
Range Command
Transmission Control
Power Command
Transmission and EDC Control
11
604.55.061.00 - 01 - 2000
6 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1
604.55.061.00 - 01 - 2000
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1 7
1
2. Peel back the cable from both ends of the
damaged area and carefully cut away the inner
cable cover at the damaged area and strip about
13 mm (1/2 inch) of insulation from the wires. Do
not cut away any wire strands.
3. Using a suitable solvent, clean about 2 inches
(50 mm) from each cover end. Clean the grey
cable cover and the individual leads.
4. Twist two bare leads together for each damaged
lead, being careful to match wire colours, then
solder the leads using resin cored solder. Tape
each repaired lead with vinyl insulation tape,
Figure 2.
2
600.00.000.00 - 00 - 1998
8 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 1
3
6. Allow the compound to cure then cover the area
with insulating tape taking the tape well over
each end of the repair. An overlap of at least 2
inches (50 mm) of tape at each end is necessary,
Figure 4.
600.00.000.00 - 00 - 1998