Professional Documents
Culture Documents
Op Amp Evaluation
Board Manual
SOT23, SC70, and
SOIC8 Package
http://onsemi.com
Description
This document describes the SOT23, SC70, and SOIC8 • Information on OP1SC70EVB (SC70 package)
package Op Amp evaluation board. It should be used in Evaluation Board
conjunction with the appropriate data sheet which contains • Information on OP1SOIC8EVB (SOIC8 package)
full technical details on the device specification and Evaluation Board
operation. This evaluation board is offered as a convenience
for the customers interested in performing their own
• Bill of Materials
engineering characterization and performance assessment. Board Lay−up
The evaluation board provides a 50 W controlled impedance The SOT23, SC70, and SOIC8 evaluation boards are
environment. The evaluation board is designed to facilitate implemented in two layers (Figure 1, Evaluation Board
a quick evaluation of the device. The default populated Lay−up). The first layer is the 1.0 oz copper ground plane,
evaluation board will have a gain of two. where a portion of the ground plane is cut out to mount the
This evaluation board manual contains: device. The FR4 dielectric material is placed between the
• Information on OP1SOT23EVB (SOT23 package) first and second layer. The second layer contains the rest of
the components and primary signal traces.
Evaluation Board
Top Silkscreen
Top Soldermask
Top Plating
0.062 + / − 0.010
Adjust
Bottom Soldermask
Bottom Silkscreen
Board Design
The evaluation board was designed for non−inverting op evaluation board has versatile loading options for the op
amp configuration (Figure 2). The input contains amp through C9, R10, and R11 depending on the user’s
termination resistor R3 (usually 50 Ω). The input can also be preference it can be configured as capacitive load, series
monitored through J1 when R1 and R2 are populated. The resistance load, parallel resistance load, etc.
D6 C7 C6 C5 C3 C2 C1 D7
R7 R5
EN
JMP1
BNC Connector
Scope
J1 R1 R2
+
−
BNC Connector R10 BNC Connector
IN
R3 VEE VCC Out
J2 C9 R11 J3
R6
R4
• L1, L2, C1, C2, C3, C5, C6, C7, D6, D7, R5, and R7 • C9, R10, and R11 are for different loading
are for power supply noise suppression configuration of the op amp
• R3 is for input matching of 50 W trace • If enable pin is available, the Jumper 1 can be used to
• R1 and R2 are for monitoring the input signal enable or disable the device
• R4 and R6 are for feedback resistors
http://onsemi.com
2
OPAMP1EVB
Board Layout
Figure 3 shows the board layout of the SOT23 package (SC70 board layout is similar to SOT23 board layout) and Figure 4
shows the board layout of the SOIC8 package.
Top View
Bottom View
http://onsemi.com
3
OPAMP1EVB
Top View
Bottom View
http://onsemi.com
4
OPAMP1EVB
http://onsemi.com
5
OPAMP1EVB
http://onsemi.com
6
OPAMP1EVB
http://onsemi.com
7
OPAMP1EVB
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
http://onsemi.com OPAMP1EVB/D
8