Professional Documents
Culture Documents
Fujitsu LifeBook ®
A6025 Notebook
User’s Guide
fennec3.book Page 2 Wednesday, May 23, 2007 3:43 PM
fennec3.book Page 3 Wednesday, May 23, 2007 3:43 PM
Copyright
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name: Fujitsu Computer Systems Corporation
Address: 1250 E. Arques Avenue, M/S 122
Sunnyvale, CA 94085
Telephone: (408) 746-6000
Declares that product: Base Model Configuration:
LifeBook A6025 notebook
Complies with Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:
(1) This device may not cause harmful interference, (2) This device must accept any interference received,
including interference that may cause undesired operation.
fennec3.book Page 4 Wednesday, May 23, 2007 3:43 PM
+ turer’s instruction.
Ta b l e o f C o n t e n t s
4 5
USER-INSTALLABLE FEATURES TROUBLESHOOTING
Identifying the Problem . . . . . . . . . . . . . . . . . . . 45
Lithium ion Battery Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 45
Recharging the Batteries. . . . . . . . . . . . . . . . . . . 29
Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 46
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 30
Power On Self Test Messages . . . . . . . . . . . . . . 53
Optical Disk Drive Emergency Media Player Drive Tray Release . . . 54
Media Player Software . . . . . . . . . . . . . . . . . . . . 31 Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 54
Loading Media on Your Drive . . . . . . . . . . . . . . 31 Restoring Your Pre-installed Software . . . . . . . . 55
Removing Media . . . . . . . . . . . . . . . . . . . . . . . . 32 Restoring the Factory Image . . . . . . . . . . . . . . . 55
Emergency Media Tray Release . . . . . . . . . . . . . 32 Using the Shock Sensor Utility . . . . . . . . . . . . . . 56
Using the Media Player Software . . . . . . . . . . . . 32 Automatically Downloading Driver Updates. . . . 57
Using Media Player on Battery Power . . . . . . . . 32
Ta b l e o f C o n t e n t s
IP address information
About IP Addresses . . . . . . . . . . . . . . . . . . . . . . 90
WLAN Specifications
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 91
1
Preface
fennec3.book Page 2 Wednesday, May 23, 2007 3:43 PM
Preface
1
fennec3.book Page 2 Wednesday, May 23, 2007 3:43 PM
2
fennec3.book Page 3 Wednesday, May 23, 2007 3:43 PM
2
Getting to Know
Your LifeBook Notebook
3
fennec3.book Page 4 Wednesday, May 23, 2007 3:43 PM
4
fennec3.book Page 5 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
5
fennec3.book Page 6 Wednesday, May 23, 2007 3:43 PM
LifeBook
Application Panel
Volume Buttons
Display Panel
Touchpad
Scroll button or
Optional Fingerprint Sensor
Status
Left Stereo Indicator Panel
Speaker
Power/Suspend/
Resume Button
Status
Indicator
Panel
Wireless LAN
Bluetooth
On/Off Switch
Microphone/
Headphone/ Line-In Jack Keyboard
Line-Out Jack
Right Stereo Speaker
6
fennec3.book Page 7 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
7
fennec3.book Page 8 Wednesday, May 23, 2007 3:43 PM
8
fennec3.book Page 9 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Anti-theft
Lock Slot
Gigabit LAN
(RJ-45) Jack Air Vents
S-Video Out Port Modem Jack
External
Video Port
USB 2.0 Ports
9
fennec3.book Page 10 Wednesday, May 23, 2007 3:43 PM
Air Vents
Memory
Upgrade
Compartment
10
fennec3.book Page 11 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
■
Orange, blinking: Blinks during battery status
■
Steady On: This means that there is power to your measurement (Four seconds after the battery is
LifeBook notebook and that it is ready for use. installed).
■ Flashing: This means that your notebook is in Sleep ■ Red, blinking: There is a problem with the battery.
mode. ■
Off: There is no battery installed.
■ Steady Off: This means that your system is either in
Save-to-Disk mode, or that your notebook has been
turned off.
■
If the battery pack is installed while the
power is turned off, the battery level
If you are charging your battery, the Power indicator will indicator will display the charge level for
remain on even if your notebook is shut off. The Power five seconds after it blinks orange.
indicator will also remain on if you have either adapter ■
If the AC adapter is not connected or the
connected and are shut down from Windows. battery pack is not fully charged when
the computer is switched to Sleep mode,
the indicator will blink. The LED blinks at
BATTERY CHARGING INDICATOR the rate of one second on/five seconds
When the AC adapter is connected to your system, this off.
indicator shows the status of the battery charging, as
follows:
■
Batteries subjected to shocks, vibration
■
Green, solid: The battery is either fully charged or the or extreme temperatures can be perma-
AC adapter is connected and there is no battery pack nently damaged.
installed. ■
A shorted battery is damaged and must
■
Orange, solid: The battery pack is charging. be replaced.
11
fennec3.book Page 12 Wednesday, May 23, 2007 3:43 PM
NUMLK INDICATOR
The NumLk indicator states that the integral keyboard is
set in ten-key numeric keypad mode.
CAPSLOCK INDICATOR
The CapsLock indicator states that your keyboard is set
to type in all capital letters.
SCRLK INDICATOR
The ScrLk indicator states that your scroll lock is active.
12
fennec3.book Page 13 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Function Keys
■
[Fn+F6]: Pressing [F6] repeatedly while holding [Fn]
will lower the brightness of your display.
■
[Fn+F7]: Pressing [F7] repeatedly while holding [Fn]
will increase the brightness of the display.
■
[Fn+F8]: Pressing [F8] repeatedly while holding [Fn]
will decrease the volume of your LifeBook notebook.
■
[Fn+F9]: Pressing [F9] repeatedly while holding [Fn]
will increase the volume of your LifeBook notebook.
■
[Fn+F10]: Pressing [F10] while holding [Fn] allows
you to change your selection of where to send your
display video. Each time you press the combination of
keys you will step to the next choice. The choices, in
order, are: built-in display panel only, both built-in
display panel and external monitor or external moni-
tor only.
14
fennec3.book Page 15 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Touchpad
Left Button
Scrolling button/
Optional Fingerprint
Right Button
Recognition Sensor
Figure 2-10. Touchpad pointing device
The left and right buttons function the same as mouse DOUBLE-CLICKING
buttons. The functionality of the buttons may vary Double-clicking means pushing and releasing the left
depending on the application being used. (Figure 2-10) button twice in rapid succession. This procedure does
not function with the right button. To double-click,
An external mouse can be connected to a move the cursor to the item you wish to select, press the
USB port on your LifeBook notebook and left button twice, then immediately release it. You also
used simultaneously with the Touchpad.
have the option to perform the double-click operation
However, if you boot the system with an
external mouse connected the Touchpad
by tapping lightly on the Touchpad twice. (Figure 2-12)
will be disabled or enabled depending on
the specifications in your BIOS settings.
(See BIOS Setup Utility on page 23 for
more information)
15
fennec3.book Page 16 Wednesday, May 23, 2007 3:43 PM
■
If the interval between clicks is too long,
SCROLLING
the double-click will not be executed. Using the scrolling sensor allows you to navigate
■
Parameters for the Touchpad can be through a document quickly without using the window’s
adjusted from the Mouse Properties scroll bars. This is particularly useful when you are navi-
dialog box located in the Windows gating through online pages. To use the scrolling sensor,
Control Panel. move your finger forward or backward across the button
to scroll up or down a page. When you have reached the
desired section of the page, raise your finger. (Figure )
DRAGGING
Dragging means pressing and holding the left button, Note that you can also scroll by sliding your finger up
while moving the cursor. To drag, move the cursor to the and down the right side of the touchpad. This feature is
item you wish to move. Press and hold the left button disabled by default, but you can enable it by going to
while moving the item to its new location and then Start -> Control Panel -> Mouse.
release it. Dragging can also be done using the
In certain models of this system, the scrolling sensor is
Touchpad. First, tap the Touchpad twice over the item
also used as a fingerprint sensor. To use the optional
you wish to move making sure to leave your finger on
fingerprint sensor device, refer to the appendix of this
the pad after the final tap. Next, move the object to its
document. (See Fingerprint Sensor Device on page 99 for
new location by moving your finger across the
more information)
Touchpad, and then release your finger. (Figure 2-13)
16
fennec3.book Page 17 Wednesday, May 23, 2007 3:43 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Volume Control
Your Fujitsu LifeBook notebook has multiple volume
controls which interact with each other.
Vol +
■
Volume can be set from within the Volume Control on
the Taskbar.
■
Volume can be controlled with the F8 and F9 func-
tions keys. Pressing [F8] repeatedly while holding [Fn]
will decrease the volume of your notebook. Pressing
[F9] repeatedly while holding [Fn] will increase the
volume of your notebook.
■
Volume can be controlled by many volume controls
that are set within individual applications.
■
Certain external audio devices you might connect to
your system may have hardware volume controls.
Each source discussed above puts an upper limit on the
volume level that must then be followed by the other
sources.
We recommend that you experiment with the various
volume controls to discover the optimal sound level.
17
fennec3.book Page 18 Wednesday, May 23, 2007 3:43 PM
My
Home
Web
Search A B C Vol +
A Notepad
B Calculator
C Unassigned
18
fennec3.book Page 19 Wednesday, May 23, 2007 3:43 PM
3
Getting Started
19
fennec3.book Page 20 Wednesday, May 23, 2007 3:43 PM
20
fennec3.book Page 21 Wednesday, May 23, 2007 3:43 PM
Getting Started
DC Power Jack
DC Output Cable
AC Adapter
AC Cable
21
fennec3.book Page 22 Wednesday, May 23, 2007 3:43 PM
Display Panel
Display Panel
Your Fujitsu LifeBook notebook contains a display panel ■
When using AC power your brightness
that is backlit for easier viewing in bright environments setting is set to its highest level by
and maintains top resolution through the use of active- default. When using battery power your
matrix technology. brightness setting is set to approximately
mid-level by default.
OPENING THE DISPLAY PANEL ■
The higher the brightness level, the
1. Press the Display Panel latch to release the locking more power the notebook will consume
mechanism, allowing you to raise the display. and the faster your batteries will dis-
charge. For maximum battery life, make
2. Lift the display backwards, being careful not to
sure that the brightness is set as low as
touch the screen, until it is at a comfortable possible.
viewing angle. (Figure 3-2)
22
fennec3.book Page 23 Wednesday, May 23, 2007 3:43 PM
Getting Started
Starting Your the main system memory is empty, and it needs to find
instructions to start up your notebook. This information
LifeBook Notebook is in the BIOS program. Each time you power up or
restart your notebook, it goes through a boot sequence
which displays a Fujitsu logo until your operating system
POWER ON is loaded. During booting, your notebook is performing
Power/Suspend/Resume Button a standard boot sequence including a Power On Self Test
The Power/Suspend/Resume button is used to turn on (POST). If the sequence is completed without a failure
your LifeBook notebook from its off state. Once you and without a request for the BIOS Setup Utility, the
have connected your AC adapter or charged the internal system displays the operating system’s opening screen.
Lithium ion battery, you can power on your LifeBook
notebook. (See figure 2-3 on page 6 for location) The boot sequence is executed when:
■
You turn on the power to your LifeBook notebook.
When you turn on your LifeBook ■
You restart your notebook from the Windows Shut
notebook be sure you have a power
Down dialog box.
source. This means that at least one
battery is installed and charged, or that the
■
The software initiates a system restart. Example: When
AC or Auto/Airline adapter is connected you install a new application.
and has power.
HARD DISK DRIVE PASSWORDS
To provide additional data security, you can assign pass-
To turn on your LifeBook notebook from its off state, words to your hard disk drive. This feature is managed in
press the Power/Suspend/Resume button, located above the system BIOS Setup Utility. See BIOS Setup Utility
the keyboard to the right. When you are done working below for information about accessing the utility.
you can either leave your LifeBook notebook in Sleep
mode, (See Standby Mode on page 27 for more informa- Remember your passwords. If you set and
tion), or you can turn it off (See Power Off on page 28 for forget your User and Master hard disk
more information). passwords, Fujitsu Computer Systems will
not be able to reset it. You may lose data
Do not carry your LifeBook notebook and have to replace your system board or
around with the power on or subject it to hard disk drive.
shocks or vibration, as you risk damaging
your hard disk drive.
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
When you power on your LifeBook, it will perform a operating environment for your LifeBook notebook.
Power On Self Test (POST) to check the internal parts and Your BIOS is set at the factory for normal operating
configuration for correct functionality. If a fault is found, conditions, therefore there is no need to set or change
your LifeBook notebook will emit an audio warning and/ the BIOS’ environment to operate your notebook.
or an error message will be displayed. (See Power On Self
Test Messages on page 55 for more information) The BIOS Setup Utility configures:
Depending on the nature of the problem, you may be able ■
Device control feature parameters, such as changing
to continue by starting the operating system or by I/O addresses and boot devices.
entering the BIOS setup utility and revising the settings. ■
System Data Security feature parameters, such as
After satisfactory completion of the Power On Self Test passwords.
(POST), your notebook will load your operating system.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following (or use
Never turn off your LifeBook notebook
the TrustedCore Menu, as detailed in the next section):
during the Power On Self Test (POST) or it
will cause an error message to be displayed 1. Turn on or restart your LifeBook notebook.
when you turn your LifeBook notebook on
2. To enter the BIOS Setup Utility, press the [F2] key
the next time. (See Power On Self Test
once the Fujitsu logo appears on the screen. This will
Messages on page 55 for more
open the main menu of the BIOS Setup Utility with
information)
the current settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key
BOOT SEQUENCE to scroll through the other setup menus to review or
The procedure for starting up your notebook is called alter the current settings.
the Bootup sequence and involves your notebook’s
BIOS. When your LifeBook notebook is first turned on,
23
fennec3.book Page 24 Wednesday, May 23, 2007 3:43 PM
Using the TrustedCore Menu 2. You will be prompted to enter your User Name and
When the Fujitsu logo appears on the screen. press the Password and you will be given a chance to select an
[Enter] key or click on the left mouse or touchpad icon for your account.
button; the TrustedCore Menu will appear. 3. The next screen asks for a Computer Name and
The TrustedCore Menu provides shortcuts to the allows you to choose a desktop background.
following menus and information screens: 4. You will next see a "Help protect Windows automat-
ically" screen in which the default choice is "Use
■
BIOS Setup recommended settings”. The other two choices are
■
Diagnostic Screen "Install important updates only" and "Ask me later".
■ Boot Menu Select from the three choices.
■ Patent Information 5. On the next screen set your time and date settings.
■
System Information 6. You will next see the "Select your computer's current
■ Continue Booting location" screen. Make your selection from Home,
Work (Default), and Public location.
Clicking on any of the fields will invoke the screen,
information, or action described. 7. The "Thank you" screen follows and an offer for free
Norton Internet Security is extended. Following are
The Boot Menu can also be invoked by pressing the several screens while Windows checks the system
[F12] key when the Fujitsu logo appears on the screen. performance.
BIOS Guide 8. Windows will then boot up for the first time.
A guide to your notebook’s BIOS is available online.
Please visit our service and support website at http:// REGISTERING WINDOWS WITH MICROSOFT
www.computers.us.fujitsu.com/support, then select 1. After Windows has booted up for the first time, the
Users Guides under Online Support. Select your Control Panel Welcome Center will appear. If the
product, series, and model, then press [Go]. Register Windows Online icon is not seen in the
window, click on “Show all 14 items”.
The first time you initialize your system, 2. Click on Register Windows Online and follow the
the screen will be blank for approximately instructions that appear to register your copy of
two minutes. This is normal. After Windows.
initialization, a “Set Up Windows” dialog
box will appear. REGISTERING YOUR LIFEBOOK NOTEBOOK
Important: During the setup procedure, do How do I register my LifeBook notebook?
not disconnect the power supply, press any You can register your LifeBook by going to our website:
buttons, or use any peripheral devices such
as a mouse, keyboard, or remote control. http://www.us.fujitsu.com/computers
You will need to be set up with an Internet Service
STARTING VISTA FOR THE FIRST TIME Provider (ISP) to register online.
In order to ensure that you receive the most benefits
from the Windows operating system, it should be
registered the first time you use it. INSTALLING CLICK ME!
1. First of all, you will need to read and accept the End The first time you boot up your system, you will see a
User License Agreements (EULAs). “Primary Settings for the PC” window. This window
explains the installations which will be performed by the
■
If you reject the terms of the license
Click Me! utility. If you click [Execute], Click Me! will
agreement you will be asked to review begin installing. If after clicking the button you receive a
the license agreement for information “User Account Control” window, you will be asked for
on returning Windows or to shut down your permission to continue. Click [Yes] to continue. If
your LifeBook notebook. you cancel the operation, the Click Me! icon will appear
■
You cannot use your notebook until you on your desktop for later installation.
have accepted the License Agreement. If
you stop the process your notebook will
return to the beginning of the Windows
Welcome Process, even if you shut your
notebook down and start it up again.
24
fennec3.book Page 25 Wednesday, May 23, 2007 3:43 PM
Getting Started
Power Management Your notebook’s system memory typically stores the file
on which you are working, open application informa-
Your Fujitsu LifeBook notebook has many options and tion, and any other data required to support operations
features for conserving battery power. Some of these in progress. When you resume operation from Sleep
features are automatic and need no user intervention, mode, your notebook will return to the point where it left
such as those for the internal modem. However, others off. You must use the Power/Suspend/Resume button to
depend on the parameters you set to best suit your oper- resume operation, and there must be an adequate power
ating conditions, such as those for the display bright- source available, or your notebook will not resume.
ness. Internal power management for your notebook
may be controlled from settings made in your operating ■
If you are running your notebook on
system, pre-bundled power management application, or battery power, be aware that the battery
from settings made in BIOS setup utility. continues to discharge while your note-
book is in Sleep mode, though not as
Besides the options available for conserving battery fast as when fully operational.
power, there are also some things that you can do to ■
Disabling the Power/Suspend/Resume
prevent your battery from running down as quickly. For button prevents it from being used to
example, you can create an appropriate power saving put the notebook into Sleep or Hiberna-
profile, put your notebook into Sleep mode when it is tion (Save-to-Disk) mode. The button
not performing an operation, and you can limit the use resume function cannot be disabled.
of high power devices. As with all mobile, battery ■
The Sleep or Hibernation (Save-to-Disk)
powered computers, there is a trade-off between mode should not be used with certain
performance and power savings. PC Cards. Check your PC Card docu-
mentation for more information. When
POWER/SUSPEND/RESUME BUTTON PC Cards or external devices are in use,
When your notebook is active, the Power/Suspend/ Hibernation (Save-to-Disk) mode cannot
Resume button can be used to manually put the note- return to the exact state prior to suspen-
book into Sleep mode. Push the Power/Suspend/Resume sion, because all of the peripheral
button when the notebook is active, but not actively devices will be re-initialized when the
accessing anything, and immediately release the button. system restarts.
■
If your notebook is actively accessing
If your notebook is suspended, pushing the Power/ information when you enter the Sleep or
Suspend/Resume button returns your notebook to active Hibernation (Save-to-Disk) mode,
operation. You can tell whether the system is in sleep changes to open files are not lost. The
mode by looking at the Power indicator. (See Figure 2-3 files are left open and memory is kept
on page 6) If the indicator is visible and not flashing, active during Sleep mode or the memory
your notebook is fully operational. If the indicator is is transferred to the internal hard drive
visible and flashing, your notebook is in Sleep mode. If during Hibernation mode.
the indicator is not visible, the power is off or your note- The main advantage of using Hibernation
book is in Hibernation mode. (See Hibernation Feature) (Save-to-Disk) is that power is not
required to maintain your data. This is
SLEEP MODE particularly important if you will be leaving
Sleep mode in Windows saves the contents of your your notebook in a suspended state for a
system memory during periods of inactivity by main- prolonged period of time. The drawback
taining power to critical parts. This mode will turn off of using Hibernation mode is that it
lengthens the power down and power up
the CPU, display, hard drive, and all the other internal
sequences and resets peripheral devices.
components except those necessary to maintain system
memory and allow for restarting. Your notebook can be
put in Sleep mode by: HIBERNATION (SAVE-TO-DISK) FEATURE
The Hibernation feature saves your system’s memory
■
Pressing the Power/Suspend/Resume button when
your system is turned on. contents to the hard drive as a part of the Sleep/Resume
■
Clicking on the power icon on the lock menu. mode. You can enable or disable this feature.
■
Selecting Sleep from the Windows Shut Down menu. Enable or Disable the Hibernation Feature
■
Timing out from lack of activity. The default settings are not enabled. To enable or disable
■
Allowing the battery to reach the Dead Battery the Hibernation feature follow these easy steps:
Warning condition.
1. From the Start menu, select Control Panel -> Power
Options.
25
fennec3.book Page 26 Wednesday, May 23, 2007 3:43 PM
POWER OFF
Before turning off the power, check that the hard drive,
optical drive, PC Card, and floppy disk indicators are all
Off. (See Figure 2-3 on page 6). If you power-off while
accessing a disk or PC Card there is a risk of data loss. To
ensure that the notebook shuts down without error, use
the Windows shutdown procedure.
26
fennec3.book Page 27 Wednesday, May 23, 2007 3:43 PM
4
User-Installable
Features
27
fennec3.book Page 28 Wednesday, May 23, 2007 3:43 PM
28
fennec3.book Page 29 Wednesday, May 23, 2007 3:43 PM
■
Actual battery life will vary based on
screen brightness, applications, fea- Low Battery State
tures, power management settings, bat- When the battery is running low, a low battery notifica-
tery condition and other customer tion message will appear. If you do not respond to the
preferences. CD-ROM drive, Multi- low battery message, the batteries will continue to
Format DVD Writer, DVD/CD-RW drive discharge until they are too low to operate. When this
combo, or hard drive usage may also happens, your notebook will go into Sleep mode. There
have a significant impact on battery life. is no guarantee that your data will be saved once the
The battery charging capacity is reduced notebook reaches this point.
as the battery ages. If your battery is
running low quickly, you should replace
it with a new one.
■
Once the low battery notification mes-
sage appears, you need to save all your
■
Under federal, state, or local law it may active data and put your LifeBook note-
be illegal to dispose of batteries by put- book into Sleep mode until you can pro-
ting them in the trash. Please take care vide a new power source. You should
of our environment and dispose of bat- provide a charged battery, an AC power
teries properly. Check with your local adapter, or Auto/Airline adapter as soon
government authority for details regard- as possible.
ing recycling or disposing of old batter-
■
When you are in Sleep mode there must
ies. If you cannot find this information
always be at least one power source
elsewhere, contact your support repre-
sentative at 1-800-8FUJITSU (1-800- active. If you remove all power sources
while your LifeBook notebook is in Sleep
838-5487)
mode, any data that has not been saved
to the hard drive will be lost.
29
fennec3.book Page 30 Wednesday, May 23, 2007 3:43 PM
Dead Battery Suspend mode shows on the Status indi- Hot-swapping Batteries
cator just like the normal Sleep mode. Once your note- To hot-swap batteries in your battery bay follow these
book goes into Dead Battery Suspend mode you will be easy steps: (Figure 4-1)
unable to resume operation until you provide a source of
power either from an adapter, or a charged battery. Once Be sure to plug in an AC Adapter prior to
you have provided power, you will need to press the removing the battery. There is no bridge
Power/Suspend/Resume button to resume operation. battery present to support the system
while the battery is being replaced. If you
In the Dead Battery Suspend mode, your data can be do not use an AC Adapter you will lose
maintained for some time, but if a power source is not any unsaved files.
provided promptly, the Power indicator will stop
flashing and go out, meaning that you have lost the data 1. Plug an AC Adapter into the system and connect it
that was not stored. Once you provide power, you can to a power outlet.
continue to use your notebook while an adapter is
charging the battery. Battery Bay
Release Latches
Shorted Batteries Battery Pack
The Status Indicator panel uses a Battery Level indicator
to display the operating level available in that battery.
(See figure 2-8 on page 11) If this display is red and
blinking, it means the battery is damaged and must be
replaced so it does not damage other parts of your Life-
Book notebook.
30
fennec3.book Page 31 Wednesday, May 23, 2007 3:43 PM
31
fennec3.book Page 32 Wednesday, May 23, 2007 3:43 PM
If you have disabled the Auto Insert USING THE MEDIA PLAYER SOFTWARE
Notification Function, you will have to
start the drive from your desktop, since Depending upon its configuration, your
your LifeBook notebook will not system may not have the media player
automatically recognize that media has software pre-installed. If it is not installed,
been loaded. reference the documentation that
accompanies the media application.
DVD movie on battery power you may need to swap in To Watch a Movie on Battery Power:
an additional, charged battery or attach AC power during 1. Have an additional full-charged battery or your AC
the movie to view it in its entirety. adapter ready for use.
2. Start watching your DVD movie.
■
Prolonged use of the optical drive, such 3. When the low battery warning occurs, immediately
as watching a DVD movie, will greatly
stop the movie and exit the media player.
reduce your notebook’s battery life.
■
Many movie run-times are longer than
your system can support on a single If you do not stop the media player quickly
battery. If you are watching a DVD and the LifeBook notebook attempts to
movie on battery power you may need auto-suspend (critical battery low state)
to swap in an additional charged battery the LifeBook notebook will shut down
or attach AC power during the movie to improperly. If this occurs, you will need to
view it in its entirety. perform a hard reset and follow the
■
An additional fully-charged battery is instruction, if any, presented to you before
highly recommended if you will be the system will reboot.
watching DVD movies on battery
power. If you do not have an additional 4. Power down your LifeBook notebook and replace
battery, you may purchase one either the discharged battery with an additional fully-
online at: www.shopfujitsu.com
charged battery. If you do not have an additional
or by calling 1-800-FUJITSU
(1-800-385-4878).
battery, you may attach AC power as soon as you see
the low battery warning.
5. Resume your LifeBook notebook by pressing the
Suspend button again. This is not required if you
attached AC power without entering sleep mode.
6. Restart your media player, locate and skip to the
chapter of the movie you were last watching.
7. Continue watching your DVD movie.
33
fennec3.book Page 34 Wednesday, May 23, 2007 3:43 PM
Memory Stick
Memory Stick/Secure such as cell phones, GPS systems, digital cameras, and
PDAs. SD Cards transfer data quickly, with low battery
Digital/xD Card Slot consumption. Like the memory stick, it uses flash
memory architecture.
Your LifeBook notebook supports the following memory xD-Picture Cards work the same as Memory Sticks and
cards, on which you can store and transfer data to and SD Cards, but they are much smaller than either one. xD-
from a variety of digital devices. These cards use flash Picture Cards are primarily used to store and transfer
memory architecture, which means they don’t need a images with devices such as cell phones.
power source to retain data.
■
SD Memory Card
■
Mini SD Card
■
Memory Stick Media
■
Memory Stick Select Media
■
Memory Stick Duo Media
■
Memory Stick PRO Media
■
xD-Picture Cards™
• Some of the media in the above list may Figure 4-6. Memory Stick, Secure Digital, and xD-Picture Cards
have more features than others.
• An adapter is required for Memory Stick INSERTING MEMORY STICK/SD/XD CARDS
Duo and Mini SD Cards.
Memory Sticks, SD Cards, and xD-Picture Cards are
• Copyright Protection Technology can-
inserted in the Memory Stick/SD/xD-Picture Card slot
not be used.
• Multi Media Cards (MMC), Secure (Figure 4-5). To insert a Memory Stick, SD Card or xD-
MMC, and SD High Capacity (SDHC) Picture Card, follow these steps:
Cards are not supported.
■
Inserting or removing a Memory Stick,
SD Card, or xD-Picture Card during your
Memory Stick is a flash memory technology developed
notebook’s shutdown or bootup process
by Sony Electronics. Memory Stick allows you to record, may damage the card and/or your note-
transfer and share digital content, such as digital pictures, book.
movies, music, voice, and computer data and applica-
■ Do not insert a card into a slot if there is
tions.
water or any other substance on the
Secure Digital (SD) Cards are very similar to Memory card as you may permanently damage
Sticks, but they are shorter. Like the Memory Stick, SD the card, your LifeBook notebook, or
Cards allow portable storage among a variety of devices, both.
34
fennec3.book Page 35 Wednesday, May 23, 2007 3:43 PM
■
See your card manual for specific
instructions on the removal of your card.
Some cards may require your LifeBook
notebook to be in Sleep Mode or Off
while removing them.
■ It is good practice to remove devices
using the Safely Remove Hardware icon
in the Notification Area at the bottom
right of the display.
35
fennec3.book Page 36 Wednesday, May 23, 2007 3:43 PM
PC Card
36
fennec3.book Page 37 Wednesday, May 23, 2007 3:43 PM
37
fennec3.book Page 38 Wednesday, May 23, 2007 3:43 PM
■
Do not remove any screws from the Figure 4-9. Opening the Memory Upgrade Compartment
memory upgrade module compartment
except the ones specifically shown in the 6. Insert the memory upgrade module at a 45° angle.
directions for installing and removing the Press the connector edge of the module firmly down
memory upgrade module. and into the connector until it lodges under the
■
The memory upgrade module can be retaining clip. You will hear a click when it is prop-
severely damaged by electrostatic dis- erly in place. (Figure 4-10)
charge (ESD). To minimize the risk,
observe the following precautions:
■ Before handling a memory module,
touch a grounded metal object to
discharge static electricity built up in
your body.
■
When installing or removing a
memory module, hold it by the edge
so as not to touch any contacts or
chips. Be careful not to touch any
internal computer terminals or
components; the oil from your fingers
could cause a short to the compo-
nents.
■ Be sure to power down your system Figure 4-10. Installing a Second Memory Module
before adding or removing memory
modules. Even if the system is in
7. Replace the cover and reinstall the screw.
hibernate or sleep states, data could
be lost or the memory could be The memory upgrade module is not
damaged if power is still available to something you routinely remove from
the system. your notebook. Once it is installed, you
can leave it in place unless you want to
change system memory capacity.
INSTALLING MEMORY UPGRADE MODULES
1. Turn off power to your notebook, remove any power
adapter (AC or auto/airline). Remove the battery. REMOVING A MEMORY UPGRADE MODULE
1. Perform steps 1 through 4 of Installing a Memory
2. Turn the notebook bottom side up, and remove the
Upgrade Module.
screw from the memory upgrade module compart-
ment. (Figure 4-9) 2. Pull the clips sideways away from each side of the
memory upgrade module at the same time.
3. Remove the cover.
3. While holding the clips out, remove the module
4. Remove the memory upgrade module from the
from the slot by lifting it up and pulling towards the
static guarded sleeve.
side of your notebook. (Figure 4-11)
5. Align the memory upgrade module with the part
side up. Align the connector edge of the memory
upgrade module with the connector slot in the
compartment.
38
fennec3.book Page 39 Wednesday, May 23, 2007 3:43 PM
39
fennec3.book Page 40 Wednesday, May 23, 2007 3:43 PM
Device Ports ■
The internal modem is designed to the
ITU-T V.90 standard. Its maximum
Your Fujitsu LifeBook notebook comes equipped with speed of 53000bps is the highest
multiple ports to which you can connect external devices allowed by FCC, and its actual connec-
including: disk drives, keyboards, modems, printers, etc. tion rate depends on the line conditions.
The maximum speed is 33600bps at
MODEM (RJ-11) TELEPHONE JACK upload.
The modem (RJ-11) telephone jack is used for an ■
The internal modem on all Fujitsu Life-
internal modem. To connect the telephone cable follow Book notebooks from Fujitsu are certi-
these easy steps: fied for use in the United States and
Canada. The modem may be certified in
1. Align the connector with the port opening. other countries.
2. Push the connector into the port until it is seated.
3. Plug the other end of the telephone cable into a
INTERNAL LAN (RJ-45) JACK
telephone outlet. (Figure 4-12)
The internal LAN (RJ-45) jack is used for a Gigabit
(10Base-T/100Base-Tx/1000Base-T) Ethernet LAN
connection. You may need to configure your notebook
to work with your particular network. (Please refer to
your network administrator for information on your
network configuration.) To connect the LAN cable
follow these easy steps:
1. Align the connector with the port opening.
2. Push the connector into the port until it is
seated.(Figure 4-13)
3. Plug the other end of the cable into a LAN outlet.
40
fennec3.book Page 41 Wednesday, May 23, 2007 3:43 PM
MICROPHONE/LINE-IN JACK
The microphone/line-in jack allows you to connect an
external mono microphone. Your microphone must be
equipped with a 1/8” (3.5 mm) mono mini-plug in
order to fit into the microphone jack of your notebook.
Figure 4-14. Connecting a USB Device
In order to connect a microphone follow these easy
IEEE 1394 PORT steps: (See figure 2-4 on page 7 for location)
The 4-pin 1394 port allows you to connect digital 1. Align the connector with the port opening.
devices that are compliant with IEEE 1394 standard. The 2. Push the connector into the port until it is seated.
IEEE 1394 standard is easy to use, connect, and discon-
nect. This port can allow up to 400 Mbps transfer rate. A S-VIDEO OUT PORT
third-party application may be required to operate your The S-Video port allows you to connect and use directly
digital device with the 1394 port. any S-Video device, such as a VCR or television. The
S-Video standard provides for a higher quality picture
The 1394 port used in this system uses a than NTSC or PAL. To connect an S-Video device,
four-pin configuration. If you intend to follow these steps: (Figure 4-16)
interface with devices which use a six-pin
configuration, you will need to purchase 1. Align the connector with the port opening.
an adapter. 2. Push the connector into the port until it is seated.
Figure 4-15. Connecting an IEEE 1394 Device 1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
HEADPHONE/LINE-OUT JACK 3. Tighten the two hold-down screws, located on
The headphone/line-out jack allows you to connect each end of the connector.
headphones or powered external speakers to your note-
book. Your headphones or speakers must be equipped
Pressing the [Fn] + [F10] keys allows you
with a 1/8” (3.5 mm) stereo mini-plug. In order to to change your selection of where to send
connect headphones or speakers follow these easy steps: your display video. Each time you press the
(See figure 2-5 on page 8 for location) key combination, you will step to the next
choice. The choices, in order, are: built-in
1. Align the connector with the port opening.
display panel only, external monitor only,
2. Push the connector into the port until it is seated. both built-in display panel and external
monitor.
41
fennec3.book Page 42 Wednesday, May 23, 2007 3:43 PM
42
fennec3.book Page 43 Wednesday, May 23, 2007 3:43 PM
5
Troubleshooting
43
fennec3.book Page 44 Wednesday, May 23, 2007 3:43 PM
44
fennec3.book Page 45 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
Troubleshooting
There may be occasions when you encounter simple 8. If you have tried the solutions suggested in the Trou-
setup or operating problems that you can solve on the bleshooting Table without success, contact your
spot, or problems with peripheral devices that can be support representative:
solved by replacing the device. The information in this Toll free: 1-800-8Fujitsu (1-800-838-5487)
section helps you isolate and resolve some of these E-mail: 8fujitsu@us.fujitsu.com
straightforward issues and identify failures that require Website: http://www.us.fujitsu.com/computers.
service. Before you place the call, you should have the following
information ready so that the customer support represen-
IDENTIFYING THE PROBLEM tative can provide you with the fastest possible solution:
If you encounter a problem, go through the following
procedure before pursuing complex troubleshooting:
■
Product name
■
Product configuration number
1. Turn off your LifeBook notebook. ■
Product serial number
2. Make sure the AC adapter is plugged into your note- ■
Purchase date
book and to an active AC power source. ■ Conditions under which the problem occurred
3. Make sure that any card inserted in the PC Card slot ■
Any error messages that have occurred
is seated properly. You can also remove the card ■
Type of device connected, if any
from the slot, thus eliminating it as a possible cause
See the Configuration Label on the bottom of your
of failure.
notebook for configuration and serial numbers. (See
4. Make sure that any devices connected to the external figure 2-7 on page 10 for location)
connectors are plugged in properly. You can also
disconnect such devices, thus eliminating them as
possible causes of failure. SPECIFIC PROBLEMS
Using the Troubleshooting Table
5. Turn on your notebook. Make sure it has been off at
least 10 seconds before you turn it back on. When you have problems with your LifeBook notebook,
try to find the symptoms under the Problem column of
6. Go through the boot sequence.
the troubleshooting table for the feature giving you
7. If the problem has not been resolved, refer to the difficulty. You will find a description of common causes
Troubleshooting Table, that follows, for more for that symptom under the column Possible Cause and
detailed troubleshooting information.
what, if anything, you can do to correct the condition
under Possible Solutions. All possible causes or solutions
If you keep notes about what you have
may not apply to your notebook.
tried, your support representative may be
able to help you more quickly by giving
additional suggestions over the phone.
45
fennec3.book Page 46 Wednesday, May 23, 2007 3:43 PM
TROUBLESHOOTING TABLE
Problem Page Problem Page
Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 46 USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 48
Optical Drive Problems . . . . . . . . . . . . . . . . . . . . page 46 PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 48
Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 47 Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 48
Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 47 Shutdown and Startup Problems . . . . . . . . . . . . page 50
Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 47 Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 51
Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 47 Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 52
Modem Problems . . . . . . . . . . . . . . . . . . . . . . . . . page 48
Audio Problems
There is no sound coming The volume is turned too low. Adjust the volume control on your notebook.
from the built-in speakers.
The software volume control is Adjust the sound volume control settings in your
set too low. software, operating system and applications.
Headphones are plugged into Plugging in headphones disables the built-in
your notebook. speakers, remove the headphones.
BIOS audio settings are Set the BIOS setup utility to the default values within
incorrect. the Multimedia Device Configuration menu. (See
BIOS Setup Utility on page 23 for more information)
Software driver is not Refer to your application and operating system
configured correctly. documentation for help.
The speakers have been muted Click on the Volume icon in the tool tray on the
using the Volume icon in the bottom right of the screen. (It looks like a speaker).
system tray. If the Mute box is checked, click on it to uncheck it.
Optical Drive Problems
LifeBook notebook fails to Protective sheet is still in the Remove the protective sheet then replace the disc in
recognize optical discs. optical drive tray. the tray.
The disc is not pushed down Open optical drive tray and reinstall the disc
onto center circle of the drive. properly.
Optical drive tray is not Push on the front of the optical drive tray until it
latched shut. latches.
Incorrect DVD Player or no Install DVD Player software. (See “Media Player
DVD Player software is Software” on page 31 for more information.)
installed.
Wrong drive designator was Verify the drive designator used by the application is
used for the disc in the applica- the same as the one used by the operating system.
tion. When the operating system is booted from a DVD/
CD, drive designations are automatically adjusted.
Note that the drive designation can be changed with
the Disk Management tool in Control Panel under
Administrative Tools -> Computer Management.
Windows Auto Insert function Start the optical drive from the desktop or applica-
is disabled. tion software or re-enable the Windows Auto Insert
function.
LifeBook notebook fails to The disc is dirty or defective. Wipe the disc. If it still will not work try another disc
recognize a disc. in the drive.
46
fennec3.book Page 47 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
The Optical Drive Access The auto insertion function is This is normal. However, you may disable this
indicator on the Status active and is checking to see if feature.
Indicator Panel blinks at a disc is ready to run.
regular intervals when no
disc is in the tray or the
optical drive is not installed.
Floppy Disk Drive Problems
You cannot access the You tried to write to a write Eject the floppy disk and set it to write enable.
optional external floppy protected floppy disk. (See Preparing a Disk for Use on page 36 for more
disk drive. information)
Floppy disk is not loaded Eject floppy disk, check orientation and re-insert.
correctly. (See Ejecting a Disk on page 36 for more information)
The floppy disk drive may not Remove and reinstall your floppy disk drive.
be properly installed.
Security is set to protect access Verify your password and security settings.
to floppy disk data.
Hard Drive Problems
You cannot access your The wrong drive designator Verify drive designator used by application is in
hard drive. was used by an application use by the operating system. When the operating
when a bootable disc was used system is booted from a disc, drive designations
to start the notebook. are automatically adjusted.
Security is set in the BIOS so Verify your password and security settings.
your operating system cannot
be started without a password.
Keyboard or Mouse Problems
The built-in keyboard does The notebook has gone into Push the Power/Suspend/Resume button.
not seem to work. Sleep mode.
Your application has locked Try to use your integrated pointing device to restart
out your keyboard. your system.
You have installed an Your external device is not Reinstall your device. (See Device Ports on page 40 for
external keyboard or properly installed. more information)
mouse, and it does not
Your operating system soft- Check your device and operating system
seem to work.
ware is not set up with correct documentation and activate the proper driver.
software driver for that device.
You have connected an Your operating system soft- Check your device and operating system
external keyboard or mouse ware is not setup with correct documentation and activate the proper driver.
and it seems to be locking software driver for that device.
up the system.
Your system has crashed. Try to restart your notebook.
Memory Problems
Your Power On screen, or Your memory upgrade module Remove and reinstall your memory upgrade
Main menu of the BIOS is not properly installed. module. (See Memory Upgrade Module on page 38
setup utility information, for more information)
does not show the correct
You have a memory failure. Check for Power On Self Test (POST) messages.
amount of installed
(See Power On Self Test Messages on page 53 for more
memory.
information)
47
fennec3.book Page 48 Wednesday, May 23, 2007 3:43 PM
Modem Problems
Messages about modem Modem operation messages See your application software documentation for
operation. are generated by whichever additional information.
modem application is in use.
USB Device Problems
You have installed a USB The device is not properly Remove and reinstall the device. (See Device Ports on
device that your LifeBook installed. page 40 for more information)
notebook does not recog-
The device may have been Close the application and restart your notebook.
nize, or the device does not
installed while an application
seem to work properly.
was running, so your notebook
is not aware of its installation.
Your device may not have the See your software documentation and activate the
correct software driver active. correct driver.
You may have the wrong I/O See your device documentation and software docu-
address selected for the device. mentation to determine the required I/O address.
Change the settings in the Device Manager.
Your device and another device Check all I/O addresses located within the Device
are assigned the same I/O Manager and any other installed hardware or soft-
address. ware to make sure there are no duplications.
PC Card/ExpressCard Problems
A card inserted in the card The card is not properly Remove and re-insert the card. (See PC Cards/
slot does not work or is inserted. ExpressCards™ on page 36 for more information)
locking up the system.
The card may have been Close the application and restart your notebook.
inserted while an application
was running, so your notebook
is not aware of its insertion.
Your software may not have See your software documentation and activate the
the correct software driver correct driver.
active.
You may have the wrong I/O See your card documentation to determine the
address selected for your card required I/O address. Change the settings in the
device. Device Manager.
Your card device and another Check all I/O addresses located within the Device
device are assigned the same Manager and any other installed hardware or soft-
I/O address. ware to make sure there are no duplications.
Power Failures
You turn on your LifeBook The installed primary battery Check the Status Indicator Panel to determine the
notebook and nothing is completely discharged, there presence and condition of the batteries. (See Status
seems to happen. is no modular bay battery Indicator Panel on page 11 for more information)
installed or there is no Power Install a charged battery or a Power adapter.
adapter (AC or Auto/Airline)
installed.
48
fennec3.book Page 49 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
You turn on your LifeBook The primary battery is Use the Status Indicator panel to verify the presence
notebook and nothing installed but is faulty. and condition of the batteries. (See Status Indicator
seems to happen. Panel on page 11 for more information) If a battery is
indicating a short, remove that battery and operate
(continued)
from another power source or replace that battery.
The battery or batteries are low. Check the Status Indicator Panel to determine the
presence and condition of the batteries. (See Status
Indicator Panel on page 11 for more information) Use
a power adapter to operate until a battery is charged
or install a charged battery.
The power adapter (AC or Verify that your adapter is connected correctly. (See
auto/airline) is not plugged Power Sources on page 21 for more information)
in properly.
The power adapter (AC or Move the AC cord to a different outlet, check for
auto/airline) has no power a line switch or tripped circuit breaker for the AC
from the AC outlet, airplane outlet. If you are using an auto/airline adapter in
seat jack, or car cigarette a car make sure the ignition switch is in the On or
lighter. Accessories position.
The power adapter (AC or Try a different power adapter or install a charged
auto/airline) is faulty. optional second battery.
Your LifeBook notebook The power management Press any button on the keyboard, or move the
turns off all by itself. parameters are set for auto mouse to restore operation. If that fails, push the
timeouts which are too short Power/Suspend/Resume button. Check your power
for your operating needs. management settings, or close your applications and
go to the Power Savings menu of the setup utility to
adjust the timeout values to better suit your needs.
You are operating on battery Install a power adapter and then push the Power/
power only and have ignored a Suspend/Resume button. (See Power Sources on
low battery alarm until the page 21 for more information)
batteries are all at the dead
battery state and your machine
has gone into Dead Battery
Suspend mode.
You have a battery failure. Verify the condition of the batteries using the
Status Indicator panel, and replace or remove
any batteries that are shorted. (See Status Indicator
Panel on page 11 for more information)
Your power adapter has failed Make sure the adapter is plugged in and the outlet
or lost its power source. has power.
Your notebook will not The installed batteries are Replace the battery with a charged one or install
work on battery alone. dead. a power adapter.
No batteries are installed. Install a charged battery.
The batteries are improperly Verify that the batteries are properly connected by
installed. reinstalling them.
Your installed batteries are Verify the condition of the batteries using the Status
faulty. Indicator panel and replace or remove any batteries
that are shorted. (See Status Indicator Panel on
page 11 for more information)
49
fennec3.book Page 50 Wednesday, May 23, 2007 3:43 PM
The batteries seem to You are running an application Use both the primary battery and an optional
discharge too quickly. that uses a lot of power due to second battery and/or use a power adapter for this
frequent hard drive access or application when at all possible.
DVD/CD-ROM access, use of
a modem or LAN PC card.
The power savings features Check the power management and/or setup utility
may be disabled. settings in the Power Savings menu and adjust
according to your operating needs.
The brightness is turned all the Turn down the brightness adjustment. The higher
way up. the brightness the more power your display uses.
The batteries are very old. Replace the batteries.
The batteries have been Replace the batteries.
exposed to high temperatures.
The batteries are too hot or too Restore the notebook to normal operating tempera-
cold. ture. Charging icon on the Status Indicator panel
will flash when battery is outside of operating range.
Shutdown and Startup Problems
The Power/Suspend/ Power/Suspend/Resume Enable the button from the Power Options control
Resume button does not button is disabled from the panel.
work. Power -> Advanced submenu
of the setup utility.
You did not hold the button Hold the button longer. This may need to be a few
in long enough. seconds if your application is preventing the CPU
from checking for button pushes.
There may be a conflict with Close all applications and try the button again.
the application software.
The system powers up and The boot sequence settings of Set the operating source by pressing the [Enter] key
displays power on informa- the setup utility are not or the left mouse button when the Fujitsu logo
tion, but fails to load the compatible with your appears. The TrustedCore Menu will appear. Select
operating system. configuration. BIOS Setup from the TrustedCore Menu.
You have a secured system Make sure you have the right password. Enter the
requiring a password to load setup utility and verify the Security settings and
your operating system. modify them as accordingly. (See BIOS Setup Utility
on page 23 for more information)
Internal hard drive was not Use the BIOS setup utility or Primary Master
detected. submenu, located within the Main menu, to try to
auto detect the internal hard drive.
An error message is Power On Self Test (POST) has See the Power On Self Test (POST) messages to
displayed on the screen detected a problem. determine the meaning and severity of the problem.
during the notebook Not all messages are errors; some are simply status
(boot) sequence. indicators. (See Power On Self Test Messages on
page 53 for more information)
Your notebook appears to BIOS setup changes were not Make sure you select Save Changes And Exit when
change setup parameters saved when you made them exiting the BIOS setup utility.
when you start it. and exited the setup utility
returning it to earlier settings.
50
fennec3.book Page 51 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
Your notebook appears to The BIOS CMOS hold-up Contact your support representative for repairs.
change setup parameters battery has failed. This is not a user serviceable part but has a normal
when you start it. life of 3 to 5 years.
(continued)
Video Problems
The built-in display is blank Something is pushing on the Clear the Closed Cover switch. (See figure 2-3 on
when you turn on your Closed Cover switch. page 6 for location)
LifeBook notebook.
The notebook is set for an Pressing [F10] while holding down the [Fn] key
external monitor only. allows you to change your selection of where to send
your display video. Each time you press the keys you
will step to the next choice. The choices, in order,
are: built-in display panel only, both built-in display
panel and external monitor or external monitor
only.
The display angle and bright- Move the display and the brightness control until
ness settings are not adequate you have adequate visibility.
for your lighting conditions.
The power management time- Press any button the keyboard, or move the mouse
outs may be set for very short to restore operation. If that fails, push the Power/
intervals and you failed to Suspend/Resume button. (The display may be shut
notice the display come on off by Sleep mode, Auto Suspend or Video Timeout)
and go off again.
The notebook turned on Power On Self Test (POST) has Contact your support representative.
with a series of beeps and detected a failure that does not
your display is blank. allow the display to operate.
The display goes blank by The notebook has gone into Press any button on the keyboard, or move the mouse
itself after you have been Video timeout, Sleep mode, or to restore operation. If that fails, push the Power/
using it. Hibernate mode because you Suspend/Resume button. Check your power manage-
have not used it for a period of ment settings, or close your applications and go to the
time. Power Options control panel.
The power management time- Press any button on the keyboard, or move the mouse
outs may be set for very short to restore operation. If that fails, push the Power/
intervals and you failed to Suspend/Resume button. (The display may be shut
notice the display come on off by Sleep Mode, Auto Suspend or Video
and go off again. Timeout).
The display does not close. A foreign object, such as a Remove all foreign objects from the keyboard.
paper clip, is stuck between the
display and the keyboard.
The display has bright or If the spots are very tiny and This is normal; do nothing.
dark spots. few in number, this is normal
for a large LCD display.
If the spots are numerous or Display is faulty; contact your support representative.
large enough to interfere with
your operation needs.
The display is dark when on The Power Management utility Press [Fn] + [F7] to increase brightness or right-
battery power. default is set on low brightness click on the battery gauge and adjust the Power
to conserve power. Options.
51
fennec3.book Page 52 Wednesday, May 23, 2007 3:43 PM
You have connected an Your BIOS setup is not set to Toggle the video destination by pressing [Fn]+ [F10]
external monitor and it enable your external monitor. together.
does not display any
Your external monitor is not Reinstall your device. (See External Video Port on
information.
properly installed. page 41 for more information)
Your operating system soft- Check your device and operating system
ware is not setup with the documentation and activate the proper driver.
correct software driver for
that device.
You have connected an Your external monitor is not See your monitor documentation and the
external monitor and it compatible with your LifeBook External Monitor Support portions of the
does not come on. notebook. Specifications section. (See Specifications on page 67
for more information)
Miscellaneous Problems
An error message is Application software often has See your application manual and help displays
displayed on the screen its own set of error message screens for more information. Not all messages are
during the operation of displays. errors some may simply be status.
an application.
52
fennec3.book Page 53 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
53
fennec3.book Page 54 Wednesday, May 23, 2007 3:43 PM
*System RAM Failed at offset: nnnn When using the internal modem with applications
System memory failed at offset nnnn of in the 64k block that are not factory installed refer to the
at which the error was detected. This means that there is application documentation.
a fault in your built-in memory. If you continue to
operate, you risk corrupting your data. Contact your
support representative for repairs.
54
fennec3.book Page 55 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
RESTORING YOUR 5. Once you have selected the components you wish to
PRE-INSTALLED SOFTWARE install, click [Install Selected Subsystems]; the
The Drivers and Applications Restore (DAR) disc components will be installed.
contains sets of device drivers and Fujitsu utilities (in 6. After the components are installed, click [OK], then
specific directories) that are unique to your computer click [Yes] when asked if you want to reboot the
configuration for use as documented below. system.
55
fennec3.book Page 56 Wednesday, May 23, 2007 3:43 PM
2. Using the arrow keys, go to the Boot menu. USING THE SHOCK SENSOR UTILITY
3. Arrow down to the Boot Device Priority submenu. The Shock Sensor Utility is designed to decrease the risk
Press [Enter]. of damage to the computer's hard disk drive (HDD) in
the event of excessive impact or vibration. The Shock
4. If “Optical Media Drive” or “CD-ROM Drive” is not
Sensor Utility also has the ability to improve the security
at the top of the list, arrow down to the drive in the
of the computer by automatically locking the computer
list, and press the space bar (or the + key) to move it
with a password when it is carried. Note that the HDD
to the top of the list (the system attempts to boot
protection and computer locking features are mutually
from the devices in the order in which they are
exclusive; both cannot be selected at the same time.
listed). Note that the BIOS for some systems will
indicate “CD-ROM Drive”, even when a DVD drive ■
Shock Sensor Utility does not completely
is connected.
protect the HDD and does not provide
5. If you have an external DVD drive connected, absolute security for the computer.
proceed to the next step; otherwise, proceed to ■
The computer may stop temporarily while
step 7. the HDD head is retracted. To restart the
6. If you have an external DVD drive connected: computer, keep the system horizontal.
• Select the Advanced menu in the BIOS window.
• Scroll down to the USB Features submenu and 1. Double-click the Shock Sensor Utility icon in the
press the Enter key to open it. Notification Area at the bottom-right of the screen.
The [Shock Sensor Utility] window appears.
• If Legacy USB Support is disabled, press the space
bar to enable it. 2. Click the [Setting] button. The [Shock Sensor Utility
Settings] window appears.
• Scroll down to SCSI SubClass Support and press
Action
the space bar to enable it.
Select the action you wish this utility to perform:
7. Press [F10], then click on [Yes] to exit the BIOS ■
Protect HDD from impact. HDD head is retracted
Setup Utility and return to the boot process. when an impact to the computer is detected.
■
Lock computer when carried. Lock the computer
Restoring the backup image
when it is being carried.
After you have changed the boot priority, you can restore ■
Nothing. No action.
a backup image when you are booting up.
Sensitivity of impact/horizontal move/fall/carry
Procedure
detection
1. Turn on the power to your system. Adjust the sensitivity of the acceleration sensor based on
2. Ensure that you have a device that can read DVDs system motion or impact.
either installed in your system or attached exter- Ignore periodic vibration.
nally to it. If vibration is periodic, disregard it.
3. Insert the Restore Disc into the drive tray.
Ignore mouse click
4. Reboot your system. When the mouse is clicked, sensitivity is temporarily
lowered.
IMPORTANT: While the operating system is
booting up during the restoration procedure, Ignore keyboard action
your screen will go blank for a short period of When the keyboard is used, sensitivity is temporarily
time. This is normal. During the period while lowered.
your screen is blank, do not press any
buttons. Please wait for the “Recovery and
Confirm calibration when user logs on
Utility” screen to be displayed, then follow Select [Confirm calibration when user logs on] if you
the instructions that appear. want to recognize the current orientation as horizontal
at logon.
5. After the system reboots, follow the instructions Perform calibration automatically when user logs
that appear to either restore your system image or on.
erase all data from your hard disk. Select [Perform calibration automatically when user logs
on] if the system is normally used on a horizontal
surface.
56
fennec3.book Page 57 Wednesday, May 23, 2007 3:43 PM
Troubleshooting
57
fennec3.book Page 58 Wednesday, May 23, 2007 3:43 PM
58
fennec3.book Page 59 Wednesday, May 23, 2007 3:43 PM
6
Care and Maintenance
59
fennec3.book Page 60 Wednesday, May 23, 2007 3:43 PM
60
fennec3.book Page 61 Wednesday, May 23, 2007 3:43 PM
Care and Maintenance 4. If your notebook will not boot after it has dried
out, call your support representative.
If you use your Fujitsu LifeBook notebook carefully, you ■
Do not use your Fujitsu LifeBook notebook in a wet
will increase its life and reliability. This section provides environment (near a bathtub, swimming pool).
some tips for looking after the notebook and its devices.
■
Always use the AC adapter and batteries that are
■
The system contains components that approved for your notebook.
can be severely damaged by electro-
static discharge (ESD). To minimize risk
■
Avoid exposure to sand, dust and other
to the components, observe the environmental hazards.
following precautions: ■
Do not expose your notebook to direct sunlight for long
■
Be sure to power down your system periods of time as temperatures above 140° F (60° C)
before adding or removing system may damage your notebook.
components. Even if the system is in
hibernate or sleep states, data could ■
Keep the covers closed on the connectors and slots when
be lost or memory could be damaged they are not in use.
if power is still available to the
system.
■
Do not put heavy or sharp objects on the computer.
■
When installing or removing a ■
If you are carrying your LifeBook notebook in a brief-
memory module, hold it by the edge case, or any other carrying case, make sure that there are
so as not to touch any contacts or no objects in the case pressing on the lid.
chips. Be careful not to touch any
internal computer terminals or ■
Never position your notebook such that the optical
components; the oil from your fingers drive is supporting the weight of the notebook.
could cause a short to the compo-
nents. ■
Do not drop your notebook.
■
Electrical equipment may be hazardous if ■
Do not touch the screen with any sharp objects.
misused. Operations of this product or
similar products, must always be super-
vised by an adult. Do not allow children
Cleaning your LifeBook notebook
access to the interior of any electrical
■
Always disconnect the power plug. (Pull the plug, not
products and do not permit them to the cord.)
handle any cables. ■ Clean your LifeBook notebook with a damp, lint-free
cloth. Do not use abrasives or solvents.
Caring for your LifeBook notebook
■
Your LifeBook notebook is a durable but sensitive elec-
■
Use a soft cloth to remove dust from the screen.
tronic device. Treat it with respect and care. Never use glass cleaners.
■
Make a habit of transporting it in a suitable carrying Storing your LifeBook notebook
case. ■ If storing your notebook for a month or longer, turn
■
Do not attempt to service the computer yourself. your LifeBook notebook off, fully charge the battery,
Always follow installation instructions closely. then remove and store all Lithium ion batteries.
■
To protect your notebook from damage and to optimize
■
Store your notebook and batteries separately. If you
system performance, be sure to keep all air vents unob- store your LifeBook with a battery installed, the battery
structed, clean, and clear of debris. This may require will discharge, and battery life will be reduced. In addi-
periodic cleaning, depending upon the environment in tion, a faulty battery might damage your LifeBook.
which the system is used. ■
Store your Fujitsu LifeBook in a cool, dry location.
■
Do not operate the notebook in areas where the air Temperatures should remain between 13ºF (-25ºC) and
vents can be obstructed, such as in tight enclosures or 140ºF (60ºC).
on soft surfaces like a bed or cushion.
■
Keep it away from food and beverages.
■
If you accidentally spill liquid on your LifeBook note-
book:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
61
fennec3.book Page 62 Wednesday, May 23, 2007 3:43 PM
62
fennec3.book Page 63 Wednesday, May 23, 2007 3:43 PM
63
fennec3.book Page 64 Wednesday, May 23, 2007 3:43 PM
64
fennec3.book Page 65 Wednesday, May 23, 2007 3:43 PM
7
System
Specifications
65
fennec3.book Page 66 Wednesday, May 23, 2007 3:43 PM
66
fennec3.book Page 67 Wednesday, May 23, 2007 3:43 PM
Specifications
Wireless LAN: ■
Built-in Touchpad pointing device with left and right
■ Integrated Intel PRO/Wireless 3945ABG buttons and scroll button.
(WM3945ABG), Wi-Fi-compliant, or, ■
Built-in Palm Rest
■ Atheros AR5006EXS (AR5BXB6) Mini-PCI wireless ■
Spill-resistant design
network card (802.11a+b/g)
■ Optional Bluetooth device for wireless personal area
External Keyboard Support
network communication (controlled by WLAN On/ USB-compatible
Off switch) External Mouse Support
LifeBook Application Panel USB-compatible
The Application Launcher/Volume buttons on your POWER
LifeBook notebook default to the following applications: Battery
Button Label Default Application Main Lithium ion battery:
6-cell, rechargeable, 10.8V, 4000 mAh, 43 Wh, or,
My Home Default Browser 4-cell, rechargeable, 14.4V, 2000 mAh, 29 Wh
Web Search www.google.com Optional additional main Lithium ion battery:
6-cell, rechargeable, 10.8V, 4000 mAh, 43 Wh
A Notepad
AC Adapter
B Calculator Autosensing 100-240V AC, supplying 19V DC, 4.22A,
80W to the LifeBook notebook, including an AC cable.
C Unassigned
Power Management
Volume - Volume Down Conforms to ACPI (Advanced Configuration and Power
Interface).
Volume + Volume Up
DIMENSIONS AND WEIGHT
Overall Dimensions
Table 7-1 Application Launcher Defaults Approximately 14.7"(w) x 10.43"(d) x 1.55”(h)
Theft Prevention Lock (360 mm x 265 mm x 39.3 mm)
Lock slot for use with security restraint systems.
Weight
DEVICE PORTS With 300 nits display and 4-cell battery:
Approximately 6.17 lbs. (2.80 kg) with battery installed
On the LifeBook notebook:
■
PC Card slot for one Type I or Type II card: PCMCIA With 450 nits display and 4-cell battery:
Standard 2.1 with CardBus support Approximately 6.39 lbs. (2.90 kg) with battery installed
■
ExpressCard slot for one ExpressCard With 300 nits display and 6-cell battery:
■ SD/Memory Stick/xD Card slot
Approximately 6.39 lbs. (2.980 kg) with battery installed
■ One 15-pin D-SUB connector for VGA external
monitor (see Display specifications) With 450 nits display and 6-cell battery:
■ Five USB 2.0 (Universal Serial Bus) connectors for Approximately 6.61 lbs. (3.00 kg) with battery installed
input/output devices
■ One IEEE 1394 (4-pin type) jack
ENVIRONMENTAL REQUIREMENTS
■
One 7-pin video out jack Temperature
■ One modular modem (RJ-11) connector
Operating: 41° to 95° F (5° to 35° C)
■ One LAN (RJ-45) connector Non-operating: 5° to 140° F (–15° to 60° C)
■
One stereo headphone/line-out jack Humidity
■ One stereo microphone/line-in jack
Operating: 20% to 85%, relative, non-condensing
Non-operating; 8% to 85%, relative, non-condensing
KEYBOARD
Built-in keyboard with all functions of 101 key PS/2 Altitude
compatible keyboards. Operating: 10,000 feet (3,048 m) maximum
■
Total number of keys: 84
■ Function keys: F1 through F12
POPULAR ACCESSORIES
■ Feature extension key: Fn
For ordering or additional information on Fujitsu
■
Two Windows keys: one Start key, one Application key accessories, visit our website at: www.shopfujitsu.com or
■ Key pitch: 19 mm
call 1-800-FUJITSU (1-800-385-4878).
■ Key stroke: 2.7 mm
68
fennec3.book Page 69 Wednesday, May 23, 2007 3:43 PM
Specifications
69
fennec3.book Page 70 Wednesday, May 23, 2007 3:43 PM
70
fennec3.book Page 71 Wednesday, May 23, 2007 3:43 PM
8
Glossary
71
fennec3.book Page 72 Wednesday, May 23, 2007 3:43 PM
72
fennec3.book Page 73 Wednesday, May 23, 2007 3:43 PM
Glossary
Glossary Boot
To start-up a computer and load its operating system
from disk, ROM or other storage media into RAM.
AC Adapter
A device which converts the AC voltage from a Bus
wall outlet to the DC voltage needed to power An electrical circuit which passes data between the CPU
your LifeBook notebook. and the sub-assemblies inside your LifeBook notebook.
ACPI Byte
Advanced Configuration and Power Interface 8 bits of parallel binary information.
BIOS Command
Basic Input-Output System. A program and set of An instruction which you give your operating system.
default parameters stored in ROM which tests and Example: run a particular application or format a floppy
operates your LifeBook notebook when you turn it on disk.
until it loads your installed operating system from disk.
Information from the BIOS is transferred to the installed Configuration
operating system to provide it with information on the The combination of hardware and software that makes
configuration and status of the hardware. up your system and how it is allocated for use.
Bit CRT
An abbreviation for binary digit. A single piece of Cathode Ray Tube. A display device which uses a beam
information which is either a one (1) or a zero (0). of electronic particles striking a luminescent screen. It
produces a visual image by varying the position and
bps intensity of the beam.
An abbreviation for bits per second. Used to describe
data transfer rates.
73
fennec3.book Page 74 Wednesday, May 23, 2007 3:43 PM
Data Driver
The information a system stores and processes. A computer program which converts application and
operating system commands to external devices into the
DC exact form required by a specific brand and model of
Direct current. A voltage or current that does not device in order to produce the desired results from that
fluctuate periodically with time. particular equipment.
74
fennec3.book Page 75 Wednesday, May 23, 2007 3:43 PM
Glossary
75
fennec3.book Page 76 Wednesday, May 23, 2007 3:43 PM
NTSC PPPoE
National TV Standards Commission. The standard for Point to Point Protocol over Ethernet.
TV broadcast and reception for the USA.
A protocol for Ethernet, using a Point-to-Point Protocol
Operating System (PPP), which is used for connection on the phone line.
A group of control programs that convert application
Program
commands, including driver programs, into the exact
An integrated set of coded commands to your
form required by a specific brand and model of micro-
computers telling your hardware what to do and how
processor in order to produce the desired results from
and when to do it.
that particular equipment.
Protocol
Partition
Procedures and rules use to send and receive data
A block of space on a hard drive which is set aside and
between computers.
made to appear to the operating system as if it were a
separate disk, and addressed by the operating system - Method of sending and receiving data
accordingly.
- Process used to handle communication errors
PCI
Conditions required for communication are organized
Peripheral Component Interconnect in procedures for correct transfer of information.
Self-configuring PC local bus. Designed by Intel, PCI has
gained wide acceptance as a standard bus design. RAM
Random Access Memory. A hardware component of
PCMCIA your LifeBook notebook that holds binary information
PCMCIA is a trademark of the Personal Computer (both program and data) as long as it has the proper
Memory Card International Association. The Personal power applied to it.
Computer Memory Card International Association is an
organization that sets standards for add-in cards for RAM Module
personal computers. A printed circuit card with memory and associated
circuitry which allows the user to add additional
Peripheral Device memory to the computer without special tools.
A piece of equipment which performs a specific
function associated with but not integral to a computer. Reset
Examples: a printer, a modem, a CD-ROM. The act of reloading the operating system. A reset erases
all information stored in RAM.
Pitch (keyboard)
The distance between the centers of the letter keys of a Restart
keyboard. See Reset.
Pixel Resume
The smallest element of a display, a dot of color on your To proceed after interruption. In your notebook this
display screen. The more pixels per area the clearer your refers to returning to active operation after having been
image will appear. in one of the suspension states.
POST ROM
Power On Self Test. A program which is part of the BIOS Read Only Memory. A form of memory in which infor-
which checks the configuration and operating condition mation is stored by physically altering the material. Data
of your hardware whenever power is applied to your stored in this way can not be changed by your notebook
notebook. Status and error messages may be displayed and does not require power to maintain it.
before the operating system is loaded. If the self test
SDRAM
detects failures that are so serious that operation can not
Synchronous Dynamic Random Access Memory.
continue, the operating system will not be loaded.
76
fennec3.book Page 77 Wednesday, May 23, 2007 3:43 PM
Glossary
SRAM VGA
Static random access memory. A specific technology of Video Graphics Array. A video display standard
making RAM which does not require periodic data originally introduced by IBM with the PS/2 series of
refreshing. personal computers.
SSID VRAM
Service Set Identifier Video Random Access Memory. A memory dedicated to
video display data and control.
Specifies which network you are joining. Some systems
allow you to specify any SSID as an option so you can
WFM
join any network.
Wired for Management is Intel’s broad-based initiative
to reduce the total cost of ownership (TCO) of business
Standby
computing without sacrificing power and flexibility.
To make inoperative for a period of time. Your LifeBook
notebook uses various suspension states to reduce power Wi-Fi Compatible
consumption and prolong the charge of your battery. Wi-Fi (Wireless Fidelity) Identifies that the product has
passed the interoperability test, supplied by the WECA
Status Indicator
(Wireless Ethernet Compatibility Alliance), which guar-
A display which reports the condition of some portion
antees the interoperability of wireless IEEE 802.11 LAN
of your hardware. On your LifeBook notebook this is an
products. For more information on the Wi-Fi standard,
LCD screen just above the keyboard.
go to the WECA website at: www.wirelessethernet.com.
Stereo (audio)
WLAN
A system using two channels to process sound from two
Wireless Local Area Network. A wireless interconnection
different sources.
of computers and peripherals within a single limited
geographic location which can pass programs and data
SVGA
amongst themselves.
Super VGA.
Write Protect
S-Video
Prevent alteration of the binary state of all bits in a
Super Video. A component video system for driving a
storage media. Example: all information on a device
TV or computer monitor.
such as a floppy diskette; a block of space in a storage
System Clock media such as a partition of a hard drive; a file or direc-
An oscillator of fixed precise frequency which synchro- tory of floppy diskette or hard drive.
nizes the operation of the system and is counted to
XGA
provide time of day and date.
Extended VGA.
TCP/IP
Transmission Control Protocol/Internet Protocol.
A standard Internet protocol that is most widely used.
TFT
Thin Film Transistor – A technology for flat display
panels which uses a thin film matrix of transistors to
control each pixel of the display screen individually.
UL
Underwriters Laboratories – An independent organiza-
tion that tests and certifies the electrical safety of devices.
USB
Universal Serial Bus.
Standard that allows you to simultaneously connect up
to 127 USB devices such as game pads, pointing devices,
printers, and keyboards to your computer.
77
fennec3.book Page 78 Wednesday, May 23, 2007 3:43 PM
78
fennec3.book Page 79 Wednesday, May 23, 2007 3:43 PM
Regulatory Information
79
fennec3.book Page 80 Wednesday, May 23, 2007 3:43 PM
80
fennec3.book Page 81 Wednesday, May 23, 2007 3:43 PM
Appendix A
Integrated Wireless
LAN User’s Guide
81
fennec3.book Page 82 Wednesday, May 23, 2007 3:43 PM
82
fennec3.book Page 83 Wednesday, May 23, 2007 3:43 PM
W i r e l e s s L A N U s e r ’s G u i d e
83
fennec3.book Page 84 Wednesday, May 23, 2007 3:43 PM
84
fennec3.book Page 85 Wednesday, May 23, 2007 3:43 PM
W i r e l e s s L A N U s e r ’s G u i d e
■
The WLAN device operates in the 2.4GHz ISM band
and the 5 GHz lower, middle, and upper UNII bands.
■
Microwave ovens may interfere with the operation of
WLAN devices since they operate in the same 2.4GHz
frequency range as IEEE802.11b/g devices. Interfer-
ence by microwaves does not occur with IEEE802.11a
radio which operates in the 5 GHz RF band.
■
Wireless devices that transmit in the 2.4GHz range
may interfere with operation of WLAN devices in
IEEE802.11b/g modes. Symptoms of interference
include reduced throughput, intermittent disconnects,
and many frame errors. It is HIGHLY recommended Figure A-3. Wireless LAN/Bluetooth On/Off Switch
that these interfering devices be powered off to ensure
proper operation of the WLAN device. ACTIVATING THE WLAN DEVICE
Activation of the WLAN device can be accomplished
DEACTIVATING THE WLAN DEVICE using the same methods as the deactivation process
Deactivation of the WLAN device may be desired in ■
Using the Wireless On/Off Switch
certain circumstances (to extend battery life) or where
certain environments require it (i.e. hospitals, clinics, ■
In Windows, by right-clicking the WLAN icon then
airplanes, etc.). clicking “Connect to a network”
Access Point*
Wireless LAN
*An optional hub for a wired
LAN may be required depending
upon the type of access point used.
85
fennec3.book Page 86 Wednesday, May 23, 2007 3:43 PM
CONNECTING TO A NETWORK
After you have configured your computer, you can
connect to an active network by performing the
following steps:
1. Click on the WLAN icon in the system tray.
2. Select “connect to a network”.
3. Select a network from the list that appears, and
click the [Connect] button.
86
fennec3.book Page 87 Wednesday, May 23, 2007 3:43 PM
W i r e l e s s L A N U s e r ’s G u i d e
TROUBLESHOOTING
Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the
following table.
Unavailable Incorrect network Ad hoc connection: verify that the network names (SSID’s) and network
network name (SSID) or keys (WEP) of all computers to be connected have been configured
connection network key correctly. SSID’s and WEP key values must be identical on each
machine.
Access Point (Infrastructure) connection: set the network name (SSID)
and network key to the same values as those of the access point.
Set the Network Authentication value identically to that of the Access
Point. Please consult your network administrator for this value, if neces-
sary.
Weak received signal Ad hoc connection: Retry connection after shortening the distance to
strength and/or link the destination computer or removing any obstacles for better sight.
quality
Access Point (Infrastructure) connection: Retry connection after short-
ening the distance to the access point or removing any obstacles for
better sight.
The WLAN device Check if the wireless switch is turned ON. Also verify “Disable Radio” is
has been deactivated not checked in “Network setting” window.
or disabled
RF interference from The use of identical or overlapping RF channels can cause interference
Access Points or with the operation of the WLAN device. Change the channel of your
other wireless Access Point to a channel that does not overlap with the interfering
networks device.
Incorrect IP address This only applies to networks using static IP addresses. Please contact
configuration your network administrator for the correct settings.
87
fennec3.book Page 88 Wednesday, May 23, 2007 3:43 PM
W i r e l e s s L A N U s e r ’s G u i d e
89
fennec3.book Page 90 Wednesday, May 23, 2007 3:43 PM
IP address information
ABOUT IP ADDRESSES
90
fennec3.book Page 91 Wednesday, May 23, 2007 3:43 PM
W i r e l e s s L A N U s e r ’s G u i d e
WLAN Specifications
SPECIFICATIONS
Item Specification
Type of network The Intel PRO/Wireless 3945ABG Network Connections WLAN
and Atheros AR5006EXS (AR5BXB6) Mini-PCI wireless
network card (802.11a+b/g) devices conform to IEEE 802.11a
and 802.11b/g (Wi-Fi based)*.
Transfer rate (Automatic switching) 54 Mbps maximum data rate
Active frequency 802.11b/g: 2400~2473 MHz
802.11a: 4900 ~ 5850 MHz
Number of channels 802.11a: 8 independent channels
802.11b/g: 11 channels, 3 non-overlapping channels
Typical operating distances** 802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps
802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps
802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps
Security Encryption Types - WEP, TKIP, AES***
WPA 1.0 compliant
Encryption Key lengths Supported: 64 bits and 128 bits
802.1x/EAP
Maximum recommended number of computers 10 units or less ****
to be connected over wireless LAN (during ad hoc
connection)
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of
wireless LAN (Wi-Fi Alliance) has been passed.
** The communication ranges shown above will increase or decrease depending on factors such as number of walls,
reflective material, or interference from external RF sources.
*** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/
104 bits after subtracting the fixed length of 24 bits.
**** Depending on practical environments, the allowable number of computers to be connected may be decreased.
91
fennec3.book Page 92 Wednesday, May 23, 2007 3:43 PM
2. In the Control Panel, double-click the This equipment may not be modified, altered, or
Fujitsu Radio Control icon. changed in any way without signed written permission
from Fujitsu. Unauthorized modification will void the
3. In the window that appears, click the
button associated with Bluetooth and/
equipment authorization from the FCC and Industry
or Wireless LAN Status to enable or dis- Canada and the warranty.
able the individual devices.
4. Click [OK].
92
fennec3.book Page 93 Wednesday, May 23, 2007 3:43 PM
Appendix B
Using the Optional
Fingerprint Sensor
93
fennec3.book Page 94 Wednesday, May 23, 2007 3:43 PM
94
fennec3.book Page 95 Wednesday, May 23, 2007 3:43 PM
■ Resume from Sleep mode For installation, OmniPass requires that the
■
Cancel a password-protected screen saver user installing OmniPass have
administrative privileges to the system. If
■
Log into websites that require a username and your current user does not have
password administrative privileges, log out and then
log in with an administrator user before
After you have “enrolled” - or registered - your finger- proceeding with OmniPass installation.
print, you can simply swipe your fingertip over the
sensor for the system recognize you.
To install OmniPass on your system you must:
The fingerprint sensor uses Softex OmniPass which
provides password management capabilities to 1. Insert the installation media for the OmniPass appli-
Microsoft Windows operating systems. OmniPass cation into the appropriate drive. If you are
enables you to use a "master password" for all Windows, installing from CD-ROM or DVD-ROM, you must
applications, and on-line passwords. find and launch the OmniPass installation program
(setup.exe) from the media.
The use of OmniPass results in a secure authentication 2. Follow the directions provided in the OmniPass
system for restricting access to your computer, applica- installation program. Specify a location to which
tions, websites, and other password-protected resources. you would like OmniPass installed. It is recom-
OmniPass presents a convenient graphical user interface, mended that you NOT install OmniPass in the root
through which you can securely manage passwords, directory (e.g. C:\).
users, and multiple identities for each user. 3. Once OmniPass has completed installation you will
be prompted to restart you system. Once your
system has rebooted you will be able to use
OmniPass. If you choose not to restart immediately
95
fennec3.book Page 96 Wednesday, May 23, 2007 3:43 PM
after installation, OmniPass will not be available for 4. Follow the directions to uninstall the OmniPass
use until the next reboot. application.
The installation program automatically places an icon 5. Once OmniPass has finished uninstalling, reboot
(Softex OmniPass) in the Windows Control Panel as well your system when prompted.
as a golden key shaped icon in the System Tray.
USER ENROLLMENT
Verifying Information about OmniPass Before you can use any OmniPass features you must first
After you have completed installing OmniPass and enroll a user into OmniPass.
restarted your system, you may wish to check the version
of OmniPass on your system. Master Password Concept
Computer resources are often protected with passwords.
To check the version information of OmniPass: Whether you are logging into your computer, accessing
1. From the Windows Desktop, double-click the key- your email, e-banking, paying bills online, or accessing
shaped OmniPass icon in the System Tray (usually network resources, you often have to supply credentials
located in the lower right corner of the screen), to gain access. This can result in dozens of sets of creden-
or, tials that you have to remember.
Click the Start button, select Settings, and click During OmniPass user enrollment a "master password”
Control Panel (if you are using Windows XP you is created for the enrolled user. This master password
will see the Control Panel directly in the Start menu; “replaces” all other passwords for sites you register with
click it, then click Switch to Classic View). Double- OmniPass.
click Softex OmniPass in the Control Panel, and the
OmniPass Control Center will appear. If it does not Example: A user, John, installs OmniPass on his system
appear, then the program is not properly installed, (his home computer) and enrolls an OmniPass user with
or, username “John_01” and password “freq14”. He then
Click the Start button, select Programs, and from goes to his webmail site to log onto his account. He
the submenu select the Softex program group, from inputs his webmail credentials as usual (username
that submenu click OmniPass Control Center. “John_02” and password “lifebook”), but instead of
2. Select the About tab at the top of the OmniPass clicking [Submit], he directs OmniPass to Remember
Control Panel. The About tab window appears with Password. Now whenever he returns to that site,
version information about OmniPass. OmniPass will prompt him to supply access credentials.
John enters his OmniPass user credentials (“John_01”
Uninstalling OmniPass
and “freq14”) in the OmniPass authentication prompt,
and he is allowed into his webmail account. He can do
Before you uninstall the software, decrypt
this with as many websites or password protected
all OmniPass encrypted files and export all
OmniPass User Profiles. Failure to do so
resources he likes, and he will gain access to all those
may result in permanent loss of encrypted sites with his OmniPass user credentials (“John_01” and
file data, and permanent loss of all “freq14”). This is assuming he is accessing those sites
remembered passwords and associated with the system onto which he enrolled his OmniPass
information (see Chapter 5 of the user. OmniPass does not actually change the credentials
OmniPass help document: Exporting and of the password protected resource. If John were to go to
Importing Users). an Internet cafe to access his webmail, he would need to
enter his original webmail credentials (“John_02” and
“lifebook”) to gain access. If he attempts his OmniPass
For uninstallation, OmniPass requires that
the user uninstalling OmniPass have
user credentials on a system other than where he
administrative privileges to the system. If enrolled that OmniPass user, he will not gain access.
your current user does not have
administrative privileges, log out and then The enrollment procedure assumes you
log in with an administrator user before have no hardware authentication devices
proceeding with OmniPass uninstallation. or alternate storage locations that you
wish to integrate with OmniPass. If you
desire such functionality, consult the
To remove the OmniPass application from your system: appropriate sections of this document.
1. Click Start on the Windows System Tray. Select
Settings, and then Control Panel. Basic Enrollment
2. Double-click Add/Remove Programs. The Enrollment Wizard will guide you through the
3. Select OmniPass, and then click Change/Remove. process of enrolling a user. Unless you specified other-
96
fennec3.book Page 97 Wednesday, May 23, 2007 3:43 PM
wise, after OmniPass installation the Enrollment Wizard capture screen times out, click [Back] to restart the
will launch on Windows login. If you do not see the fingerprint enrollment process.
Enrollment Wizard, you can bring it up by clicking Start
on the Windows System Tray; select Programs; select Your system has a “swipe” fingerprint sensor. A
Softex; click OmniPass Enrollment Wizard. swipe sensor is small and resembles a skinny elon-
gated rectangle. To capture a fingerprint, gently
1. Click Enroll to proceed to username and password
swipe or pull your fingertip over the sensor (starting
verification. By default, the OmniPass Enrollment
at the second knuckle) towards yourself (Figure
Wizard enters the credentials of the currently logged
B-2). Swiping too fast or too slow will result in a
in Windows user.
failed capture. The Choose Finger screen has a
2. Enter the password you use to log in to Windows. [Practice] button; click it to practice capturing your
This will become the “master password” for this fingerprint. When you are comfortable with how
OmniPass user. In most cases, the Domain: value your fingerprint is captured, proceed to enroll a
will be your Windows computer name. In a corpo- finger.
rate environment, or when accessing corporate
3. Once OmniPass has successfully acquired the finger-
resources, the Domain: may not be your Windows
print, the Verify Fingerprint screen will automati-
computer name. Click [Next] to continue.
cally appear. To verify your enrolled fingerprint,
3. In this step OmniPass captures your fingerprint. place your fingertip on the sensor and hold it there
Refer to “Enrolling a Fingerprint” on page 97 for as if you were having a fingerprint captured.
additional information. Successful fingerprint verification will show a green
4. Next, choose how OmniPass notifies you of various fingerprint in the capture window and the text Veri-
events. We recommend you keep Taskbar Tips on fication Successful under the capture window.
Beginner mode taskbar tips and Audio Tips on at
least Prompt with system beeps only until you get
accustomed to how OmniPass operates. Click [Next]
to proceed with user enrollment. You will then see a
Congratulations screen indicating your completion
of user enrollment.
5. Click [Done] to exit the OmniPass Enrollment
Wizard. You will be asked if you’d like to log in to
OmniPass with your newly enrolled user; click [Yes].
Enrolling a Fingerprint
Figure B-2 Swiping a finger
Enrolling a fingerprint will increase the security of your
system and streamline the authentication procedure. USING OMNIPASS
You enroll fingerprints in the OmniPass Control Center. You are now ready to begin using OmniPass. Used regu-
With an OmniPass user logged in, double-click the noti- larly, OmniPass will streamline your authentications.
fication area OmniPass icon. Select the User Settings tab Password Replacement
and click Enrollment under the User Settings area. Click You will often use the password replacement function.
Enroll Authentication Device and authenticate at the When you go to a restricted access website (e.g., your
authentication prompt to start device enrollment. bank, your web-based email, online auction or payment
1. During initial user enrollment, you will be sites), you are always prompted to enter your login
prompted to select the finger you wish to enroll. credentials. OmniPass can detect these prompts and you
Fingers that have already been enrolled will be can teach OmniPass your login credentials. The next
marked by a green check. The finger you select to time you go to that website, you can authenticate with
enroll at this time will be marked by a red arrow. your fingerprint to gain access.
OmniPass will allow you re-enroll a finger. If you OmniPass Authentication Toolbar
choose a finger that has already been enrolled and After installing OmniPass and restarting, you will notice
continue enrollment, OmniPass will enroll the a dialog you have not seen before at Windows Logon.
fingerprint, overwriting the old fingerprint. Select a This is the OmniPass Authentication Toolbar, and it is
finger to enroll and click [Next]. displayed whenever the OmniPass authentication system
2. It is now time for OmniPass to capture your selected is invoked. The OmniPass authentication system may be
fingerprint. It may take a several capture attempts invoked frequently: during Windows Logon, during
before OmniPass acquires your fingerprint. Should OmniPass Logon, when unlocking your workstation,
OmniPass fail to acquire your fingerprint, or if the when resuming from sleep or hibernate, when unlocking
97
fennec3.book Page 98 Wednesday, May 23, 2007 3:43 PM
a password-enabled screensaver, during password Less secure is the option to Automatically enter this
replacement for remembered site or application logins, password protected site when it is activated. Do not
and more. When you see this toolbar, OmniPass is prompt for authentication. Check the upper box to get
prompting you to authenticate. this setting, and each time you navigate to this site
OmniPass will log you into the site without prompting
The Logon Authentication window indicates what
you to authenticate.
OmniPass-restricted function you are attempting. The
icons in the lower left (fingerprint and key) show what
This setting is more convenient in that
authentication methods are available to you. Selected whenever you go to a site remembered
authentication methods are highlighted while unselected with this setting, you will bypass any
methods are not. When you click the icon for an unse- authentication procedure and gain instant
lected authentication method, the authentication access to the site. But should you leave
prompt associated with that method is displayed. your system unattended with your
OmniPass user logged in, anyone using
When prompted to authenticate, you must supply the your system can browse to your password
appropriate credentials: an enrolled finger for the finger- protected sites and gain automatic access.
print capture window or your master password for the
master password prompt (the key icon).
If you uncheck both boxes in Settings for this Password
Remembering a Password Site, OmniPass will prompt you for your master pass-
OmniPass can remember any application, GUI, or pass- word or fingerprint authentication device. Once you
word protected resource that has a password prompt. have authenticated with OmniPass your credentials will
be filled in to the site login prompt, but you will have to
Using the following procedure, you can store a set of
click the website [OK], [Submit], or [Login] button to
credentials into OmniPass. These credentials will then be
gain access to the site.
linked to your “master password” or fingerprint.
Click Finish to complete the remember password proce-
Go to a site that requires a login (username and pass-
dure. The site location, the credentials to access the site,
word), but do not log in yet. At the site login prompt,
and the OmniPass authentication settings for the site are
enter your username and password in the prompted
now stored in the OmniPass secure database. The
fields, but do not enter the site (do not hit [Enter],
OmniPass authentication settings (Settings for this Pass-
[Submit], [OK], or Login). Right-click the OmniPass
word Site) can always be changed in Vault Management.
notification area icon and select Remember Password
from the submenu. The Windows arrow cursor will Logging in to a Remembered Site
change to a golden key OmniPass cursor. Click this Whether or not OmniPass prompts you to authenticate
OmniPass cursor in the login prompt area, but do not when you return to a remembered site is determined by
click the [Login] or [Submit] button. Settings for this Password Site and can be changed in
Vault Management.
Associating a Friendly Name
After clicking the OmniPass key cursor near the login The following cases are applicable to using OmniPass to
prompt, OmniPass will prompt you to enter a “friendly login to: Windows, remembered websites, and all other
name” for this site. You should enter something that password protected resources.
reminds you of the website, the company, or the service
With Master Password
you are logging into. In its secure database, OmniPass
Once you return to a site you have remembered with
associates this friendly name with this website.
OmniPass, you may be presented with a master pass-
Additional Settings for Remembering a Site word prompt. Enter your master password and you will
When OmniPass prompts you to enter a “friendly name” be allowed into the site.
you also have the opportunity to set how OmniPass
Logging into Windows with a Fingerprint Device
authenticates you to this site. There are three effective
When logging into Windows with a fingerprint device,
settings for how OmniPass handles a remembered site.
the fingerprint capture window will now appear next to
The default setting is Automatically click the “OK” or the Windows Login screen. Place your enrolled fingertip
“Submit” button for this password protected site once on the sensor to authenticate. You will be simultaneously
the user is authenticated. With this setting, each time logged into Windows and OmniPass. The capture
you navigate to this site OmniPass will prompt you for window will also appear if you have used Ctrl-Alt-Del to
your master password or fingerprint authentication lock a system, and the fingerprint device can be used to
device. Once you have authenticated with OmniPass, log back in as stated above.
you will automatically be logged into the site.
98
fennec3.book Page 99 Wednesday, May 23, 2007 3:43 PM
99
fennec3.book Page 100 Wednesday, May 23, 2007 3:43 PM
OmniPass data for a user is backed up to a single for Domain, in a PC or SOHO environment Domain
encrypted database file. During the import process, the should be your computer name.
Windows login of the exported user is required. If the
OmniPass will notify you if the user was successfully
proper credentials cannot be supplied, the user profile
imported.
will not be imported.
Things to Know Regarding Import/Export
■
You should periodically export your user ■
Assume you export a local Windows User profile from
profile and store it in a safe place. If OmniPass. You want to import that profile to another
anything happens to your system, you machine that has OmniPass. Before you can import
can import your OmniPass profile to a the profile, a Windows user with the same login cre-
new system and have all your remem- dentials must be created on the machine importing the
bered settings and fingerprints instantly. profile.
■
You don't forget the Windows login
credentials when exporting. When you Example: I have a Windows user with the username
examine the importation, you are “Tom” and the password “Sunshine” on my system. I
prompted for authentication. The have enrolled Tom into OmniPass and remembered
credentials that will allow a user profile passwords. I want to take all my passwords to new sys-
to be imported are the Windows login tem. I export Tom’s OmniPass user profile. I go to my
credentials of the exported user. They new system and using the Control Panel I create a user
are the credentials that had to be with the username "Tom" and the password "Sun-
submitted when the user profile was shine". I can now successfully import the OmniPass
exported. You will need User Name, user data to the new system.
Password, and Domain.
■
If you export an OmniPass-only user, you can import
that user to any computer running OmniPass, pro-
Exporting an OmniPass User Profile vided that a user with that name is not already
To export a user, open the OmniPass Control Center, enrolled in OmniPass.
and click Import/Export User under Manage Users. ■
If you attempt to import a user profile who has the
Click Exports an OmniPass user profile. OmniPass will same name as a user already enrolled in OmniPass, the
prompt you to authenticate. Upon successfully authenti- OmniPass import function will fail.
cation, you must name the OmniPass user profile and OMNIPASS CONTROL CENTER
decide where to save it. An .opi file is generated, and you This section will serve to explain functions within the
should store a copy of it in a safe place. OmniPass Control Center that weren’t explained earlier.
This .opi file contains all your user specific OmniPass You can access the OmniPass Control Center any of
data, and it is both encrypted and password protected. three ways:
This user profile does NOT contain any of your
encrypted data files. ■
Double-click the golden OmniPass key shaped icon in
the Windows System Tray (typically in the lower-right
Importing an OmniPass User Profile corner of the desktop)
■
Click the Start button; select the Programs group;
You cannot import a user into OmniPass if select the Softex program group; and click the
there already is a user with the same name OmniPass Control Center selection.
enrolled in OmniPass. ■
Open the Windows Control Panel (accessible via Start
button --> Settings --> Control Panel) and double-
click the Softex OmniPass icon.
To import an OmniPass user open the OmniPass
Control Center, and click Import/Export User under User Management
Manage Users. Click Imports a new user into OmniPass The User Management tab has two major interfaces:
and then select OmniPass Import/Export File (*.opi) Add/Remove User and Import/Export User. Import/
and click Next. OmniPass will then prompt you to Export User functionality is documented in “Exporting
browse for the file you had previously exported (.opi and Importing Users” on page 99. Add/Remove User
file). When you select the .opi file for importation, functionality is straightforward.
OmniPass will prompt you for authentication. The
If you click Adds a new user to OmniPass you will start
credentials that will allow a user profile to be imported
the OmniPass Enrollment Wizard. The Enrollment
are the Windows login credentials of the exported user.
Wizard is documented in “User Enrollment” on page 96.
They are the credentials that had to be submitted when
the user profile was exported. You will need User Name,
Password, and Domain. If you don’t remember the value
100
fennec3.book Page 101 Wednesday, May 23, 2007 3:43 PM
101
fennec3.book Page 102 Wednesday, May 23, 2007 3:43 PM
102
fennec3.book Page 103 Wednesday, May 23, 2007 3:43 PM
Index
Index
A D
AC DC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40, 68
plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Anti-theft lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Disk care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Application Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 22
Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 21 adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Automatically Downloading Driver Updates . . . . . . 57 brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
B latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
charging indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Drivers and Application Restore Disc . . . . . . . . . . . . 55
dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 DVD drive
faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 tray release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
lithium ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . 29
low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 E
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49, 50 Emergency Optical Drive Release . . . . . . . . . . . . . . . . . 7
recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 ExpressCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 External Floppy Disk Drive problems . . . . . . . . . . . . 47
BIOS External Video Port . . . . . . . . . . . . . . . . . . . . . . . . . 9, 41
guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 F
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 FDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57, 69
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . . . 95
Built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . . . 97
getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
C installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . 95
CapsLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 logging into a remembered site . . . . . . . . . . . . . . . 98
OmniPass authentication toolbar . . . . . . . . . . . . . 97
Click Me! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 password replacement . . . . . . . . . . . . . . . . . . . . . . . 97
Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 remembering a password . . . . . . . . . . . . . . . . . . . . 98
Cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 uninstalling OmniPass . . . . . . . . . . . . . . . . . . . . . . 96
user enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . 10, 67
using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . 6
Flexible Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . 1
Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Fujitsu Driver Update utility . . . . . . . . . . . . . . . . . 57, 69
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fujitsu LifeBook
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
103
fennec3.book Page 104 Wednesday, May 23, 2007 3:43 PM
104
fennec3.book Page 105 Wednesday, May 23, 2007 3:43 PM
Index
R T
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Removing a Memory Stick . . . . . . . . . . . . . . . . . . . . . 35 buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Touchpad Pointing Device . . . . . . . . . . . . . . . . . . . . . . 6
Restoring Your Pre-installed Software . . . . . . . . . . . . 55
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 U
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
S
USB 2.0 Ports . . . . . . . . . . . . . . . . . . . . . . 8, 9, 10, 40, 48
ScrLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SD Card V
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 38 W
Security Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Shock Sensor Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 start keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Wireless LAN
Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Before Using the Wireless LAN . . . . . . . . . . . . . . . 84
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . 68 Connection using Wireless Zero Tool . . . . . . . . . . 86
Environmental Requirements . . . . . . . . . . . . . . . . . 68 IP address information . . . . . . . . . . . . . . . . . . . . . . 90
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Wireless LAN Glossary . . . . . . . . . . . . . . . . . . . . . . 88
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 X
Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . 6, 11 xD Card
Stereo Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
105
fennec3.book Page 106 Wednesday, May 23, 2007 3:43 PM
106
fennec3.book Page 107 Wednesday, May 23, 2007 3:43 PM
fennec3.book Page 108 Wednesday, May 23, 2007 3:43 PM
fennec3.book Page 109 Wednesday, May 23, 2007 3:43 PM
fennec3.book Page 110 Wednesday, May 23, 2007 3:43 PM