Professional Documents
Culture Documents
1
III B.Tech I Semester Regular Examinations, November 2008
INDUSTRIAL ELECTRONICS
(Instrumentation & Control Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
3. (a) Sketch a regulator circuit that uses an LM 217 IC positive voltage regulator
and explain its working.
(b) Define short period and long period accuracy of a stabilizer. Give typical
values of these parameters. [8+8]
5. (a) Draw the circuit and describe the working of a series inverter. Draw the
waveforms of various current and voltages involved?
(b) Write expressions for the frequency of output voltage and attenuation factor
in the above circuit. [16]
(a) DIAC
(b) TRIAC. [8+8]
7. Draw the block diagram of digital timer counting unit and explain its operation.
[16]
⋆⋆⋆⋆⋆
1 of 1
Code No: R05312202 Set No. 2
III B.Tech I Semester Regular Examinations, November 2008
INDUSTRIAL ELECTRONICS
(Instrumentation & Control Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) Draw a Darlington emitter follower circuit and derive the h-parameters for
this circuit.
(b) Discuss about stabilization in DC amplifier with the help of relevant circuit
diagrams. [8+8]
2. (a) Explain the series regulator using pre-regulator and Darlington pair.
(b) What are the different protection techniques used in regulated power supplies?
[8+8]
3. (a) Differentiate between the linear and switched mode voltage regulators.
(b) Draw the block diagram of a servo controlled voltage stabilizer and explain
about each part in detail. [6+10]
4. (a) Explain the parallel operation of SCRs and define and derive string efficiency.
(b) Explain various protection methods for SCR. [8+8]
5. A series inverter has the following parameters: inductance L=12mH, C= 0.1 mi-
croF, load resistance R=100 Ohms and Toff=0.3millisec. Determine
6. (a) What are the principal methods of varying the DC output voltage in DC
chopper?
(b) Draw the circuit and describe the principle of operation of a type A single
quadrant DC chopper? [8+8]
7. Describe the principle of flash welding. Mention its main applications. [16]
⋆⋆⋆⋆⋆
1 of 1
Code No: R05312202 Set No. 3
III B.Tech I Semester Regular Examinations, November 2008
INDUSTRIAL ELECTRONICS
(Instrumentation & Control Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) Explain the principle of operation of a Darlington emitter follower circuit and
derive its gain.
(b) Draw the circuit diagram of a cascode transistor amplifier and explain its
working. [8+8]
3. (a) Draw the circuit of monolithic IC regulator with variable output and current
limiting features and explain it in detail.
(b) Draw a voltage regulator using LM 105 IC with an external pass transistor
and explain its working. [8+8]
4. (a) Draw typical static V-I characteristics of a thyristor and explain its salient
features.
(b) Discuss about various commutation methods used in SCR circuits. [8+8]
5. Draw the circuit of single phase full wave controlled converter with freewheel diode.
Describe its working and draw waveforms of various voltages and currents involved?
[16]
6. (a) What are the basic elements of a DC chopper? What are the characteristics
of ideal elements of DC chopper?
(b) Write about the principle of operation of a step-up DC chopper? [10+6]
7. (a) Give the classification of timers according to the technique used to achieve the
timing.
(b) Give the construction and describe the working of
i. simple bimetal strip timer and
ii. dual bimetal strip timer. [6+10]
1 of 2
Code No: R05312202 Set No. 3
(b) wood gluing
(c) food processing and
(d) electronic sewing [4+4+4+4]
⋆⋆⋆⋆⋆
2 of 2
Code No: R05312202 Set No. 4
III B.Tech I Semester Regular Examinations, November 2008
INDUSTRIAL ELECTRONICS
(Instrumentation & Control Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
4. (a) What is meant by catastrophic failure and explain the protection techniques
that are used in thyristor circuits.
(b) Define gate power dissipations and explain its importance in SCR. [8+8]
6. (a) What are the merits and drawbacks of voltage commutated thyristor dc chop-
per?
(b) Derive design expression for commutating capacitor C and commutating in-
ductor L.
(c) Derive expressions for average load voltage V0 , minimum and maximum load
voltage. [4+6+6]
7. Describe the principle of spot welding and butt welding. What are their main
applications? [16]
8. Describe the typical methods of coupling of electrodes to the R.F. generator for
dielectric heating. [16]
⋆⋆⋆⋆⋆
1 of 1