Professional Documents
Culture Documents
Establishment problems
Methods to overcome Control existing pasture and limitations weeds with spraying, cultivation
Technology used
Below 500 mm annual rainfall the most critical factor is adequate soil moisture, but in higher rainfall areas, competition from annual and perennial weeds presents the most serious challenge to successful establishment of native grasses. Generally two or more wet days will result in germination when other conditions, such as soil temperature are satisfactory. However it is the occurrence of follow-up rains, within 46 weeks of germination, that is required for successful establishment. The rate at which the soil surface dries out is critical not only for germination but also for establishment. Ideally, under cloudy conditions for several days, the soil surface will not dry out. Good followup rains will allow seedlings to develop adventitious (secondary roots) which can supply sufficient moisture for later seedling growth. More than any man-imposed management practice, it is the occurrence of these moisture conditions that will result in successful establishment.
Drilling
Conventional small seed boxes are satisfactory for sowing native grass seeds that are either naked caryopses (Caryopsis - The indehiscent fruit of most grasses with a single seed, the testa (seed coat) of which is fused with the pericarp (outer wall)) or are shed with smooth ancillary structures so that the dispersal units will flow easily. The seeds of these species generally germinate better when buried beneath the soil surface, but the number of species with these characteristics is relatively small. The dispersal units of some species (e T. triandra and .g. Austrodanthonia spp.) can be cleaned and separated into a form that can be sown using this equipment, although this is not the case for many other species of native grasses such as M. stipoides.
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 13
Picture 13 (right). Inside the B&S Industries seed box showing the rotating spring (sweeper) to prevent the seed bridging, the auger and paddle to deliver the seed to the metering box and the pegs on the cylinder of the seed metering device. The number of blades on the paddle was varied between two and four in different tests of this seed box. (Photograph R. Whalley) While this machine was able to reliably sow M. stipoides seed without clogging up, the results were unsatisfactory because of uneven distribution of the seed within the drill rows. Various modifications were tried, but even distribution of seeds could not be achieved. However, it will sow an even row of seeds of many other species. The 'Ausbox' is an all-purpose seed box that was built and manufactured by Richard Murphy, 'Wollondilly', Coonabarabran, NSW. It is especially designed to handle a wide range of slick and chaffy seeds. This box consists of a rotating spirally fluted roller that meters the seed into delivery tubes below the roller. This is an extremely simple but effective mechanism and the size of the flutes can be modified for boxes designed for different species (Picture 14).
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 14
Picture 14 (right). Inside the Ausbox showing the fluted roller that delivers seed to an air seeder. (Photographer R. Whalley) The Wiedemann/Kelly seed box (Figure 3) was designed to specifically deliver extremely chaffy seed at a consistent rate. The semi-circular seed box contains an auger agitator to keep the seed 'tumbling' and a pillar to maintain even 'density of seed' around a pickerwheel that drags the seed out of the box. This box has also been adapted to sow single rows of seed of Danthonia, Dichanthium, Themeda, Microlaena and Bothriochloa (Picture 15).
Figure 3 (below). The Wiedemann/Kelly pickerwheel seed box which meters fluffy seeds more evenly than conventional drum seeders.
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Figure 3
Picture 15. The Wiedemann/Kelly seed box adapted to sow single rows of native grasses, ideal for sowing seed production areas. (Photograph I. Cole)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 15
Crocodile seeder
The crocodile seeder originated in Queensland and has been successfully used to sow rough, unprepared sites. It consists of a steel drum with 'shovels' welded to the round surface (Picture 16 and Picture 17). When the drum is pulled on an angle, the shovels scoop out a divot of soil leaving a pitted surface with many small dams to trap and concentrate water. The steel drum is filled with seed, which falls through holes behind each shovel as it rotates, placing some seeds in each divot. The size of the divots is governed by the towing angle of the drum. It is a very robust machine and when pulled by a heavy 4WD or tractor can be used through light timber. Picture 16. The 'Crocodile' seeder can be towed behind a 4WD vehicle, comprising a one pass seeding operation creating a water harvesting pit into which seed is placed. (Photograph C. Waters)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 16
Picture 17. T. triandra successfully germinating in pits created by the 'Crocodile' seeder. (Photograph C. Waters)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 17
Other seeders
Additional ingenious devices for metering fluffy seeds are either available commercially or have been devised and built. These include rotating brushes to deliver seeds through suitable-sized holes in a plate, or belt seeders where the seeds are laid out by hand onto a V-shaped belt which rotates slowly over rollers, dropping the seeds into a furrow or onto the ground. Sowing seeds of native grasses in drill rows is appropriate for the establishment of stands for seed production (see Section 6) but is not necessary for many purposes, such as for re-vegetation following mining. Many such situations involve sowing in areas where the substrate includes numerous rocks and stones and drilling equipment is easily damaged. A far better approach under these circumstances is to broadcast the seed and
either cover lightly using chains or harrows, or simply rely on the ancillary structures to ensure that at least some seeds end up in safe sites. Seed broadcasting can be done using the seed boxes described above with the seed delivery tubes swinging free to broadcast the seed or using equipment specifically de signed for the purpose. A hydro/pneumatic seeder has been developed by John Stafford (Vegetation Management Services, Lenswood, South Australia). This machine attempts to reduce the weed problems associated with broadcasting seed by adopting the principles of row-crop management. This machine consists of three major components. A pilot spray enabling initial marking of strips, the seed drill which sows seed in a liquid polymer suspension, and a mid -row sprayer which allows inter-row weed control (Picture 18). Picture 18 (right). The hydro/pneumatic seeder sowing Chloris truncata seed into open cuts made in the fallow strips that were created and maintained by a previous application of gylphosate. (Photograph J. Stafford)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 18
Seed blowers
Two seeders designed and built by NSW Agriculture, have been developed to provide low cost seeding equipment, which can easily be built in a farm workshop. The 'cranny seeder' (Picture 19) is designed to place seed in suitable micro-sites in the landscape. Placing seed into log mounds or fallen timber has been used as a successful establishment technique in low rainfall areas. These sites concentrate nutrients and moisture and protect new seedlings from drying out and stock grazing. The Cranny seeder is mounted on a 4WD vehicle and seed is blown through a hand-held wand into suitable micro-sites while driving through a paddock. A second seeder, the 'dribble seeder' (Picture 20) is designed to spread a small amount of seed over a large area. It is mounted on a 4WD vehicle or ATV and delivers a slow trickle of seed in front of a tyre as it travels through a paddock. The dribble seeder could be used when travelling through a paddock to muster or check stock, so would not be an extra job for a landholder. The effectiveness of these techniques has not been tested, but they are more likely to work in moist conditions. Picture 19. The NSW Agriculture 'cranny seeder' blows seed into suitable micro-sites like log mounds to assist establishment and causes no soil disturbance. (Photograph C. Waters)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 19
Picture 20. The NSW Agriculture 'dribble seeder' can be mounted on an ATV to sow seed over a large area while doing other jobs. This picture shows the paddle auger that slowly dribbles the seed. This technique has not yet been evaluated, however it is expected to be most successful under moist soil conditions. (Photograph C. Waters)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 20
Air seeders
Gil Fletcher of Land Reclamation Services Pty Ltd in Emerald, Queensland, has designed and built an air seeder which will broadcast fluffy or awned native grass seeds without bridging or clogging (Picture 21). Essentially, this equipment consists of a conical hopper with a metering valve at the bottom comprising a disc on top of an open tube through which a suction is created using a sawdust extraction fan. Various stirring arms prevent the seed from bridging within the hopper. The seed-air mixture is then delivered through flexible hoses to a boom with three or four outlets so that the seed is delivered behind the machine. An additional hopper and more conventional seed metering device can be attached to deliver smooth seeds such as those of shrubs or trees, into the air stream. This equipment will also handle grass material containing a large quantity of straw provided it has been passed through a chaff cutter. Picture 21. Air seeder designed and built by Gil Fletcher of Land Reclamation Services, Emerald, QLD. The petrol motor powers a sawdust extractor fan and a stirring disk and valve powered by a 12 V motor meter the seed from the bottom of the large hopper into the air stream. The smaller hopper on the right has a more conventional seed metering device, also powered by a 12 V electric motor to deliver smooth seed into the air stream. (Photograph D. Munnich)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 21
Another seeder that is suitable for cleared land has been built by Rosedale Engineering at Gulgong. The 'Germinator' uses components from broad-acre farming machinery and is designed to cultivate the seeding row, place the seed close to the surface and cover it with a press wheel. The seed is metered from an 'Ausbox' seed box and delivered to the tines with an air system. The Germinator has worked quite successfully, although some problems with seed blockages have occurred. Modifications have been made to the seeder by NSW Agriculture and DLWC which have improved its performance (Picture 22). Picture 22. The 'Germinator', built by Rosedale Engineering at Gulgong, is a modified air seeder designed to direct drill native grass seed. The 'Ausbox' employs a fluted roller as an effective seed metering device. The air seeder system distributes the seed with minimal blockages and surface sowing boots place the seed at or very near the soil surface. (Photograph C. Waters)
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 22
Hydromulching
Hydromulching involves putting seed, dye coloured wood pulp and perhaps some fertiliser into a water-filled tank and spraying the agitated mixture on top of the soil via a 50 mm diameter hose. Ideally, the mulch should be about 20 mm thick on the soil surface to provide a stable surface for seed germination and provide some control of the germination of small seeded weeds beneath it. The agitation of the cellulose fibre in the tank and the large diameter delivery tube mean that virtually any native grass seed can be evenly sown using this equipment (Picture 23).
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.
Picture 23
Picture 23 (above). Hydromulched area beside the Armidale Bypass eight days after treatment. Note the sparse cover of the mulch and the M. stipoides seeds. (Photograph R. Whalley)
The most satisfactory mulches appear to be mulched eucalypt, sheep manure or wood pulp as used in a hydromulcher. Because M. stipoides is more abundant on acid soils, mulches which tend to make the soil more acid are likely to give it and similar species a competitive advantage over weeds.