Professional Documents
Culture Documents
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright Copyright 2006 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes. Trademarks Optiquest is a registered trademark of ViewSonic Corporation. ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners.
Revision History
Revision
1a
SM Editing Date
09/08/2006
ECR Number
Description of Changes
Initial Release
Editor
Jamie Chang
ViewSonic Corporation
VA903b-1_ VA903m-1
TABLE OF CONTENTS
1. 2. 3. 4. 5. 6. 7. 8. 9.
Precautions and Safety Notices Specification Front Panel Function Control Description Circuit Description Adjustment Procedure Troubleshooting Flow Chart Recommended Spare Parts List Exploded Diagram and Exploded Parts List Block Diagram
1 4 13 16 23 47 55 60 65 66 72
ViewSonic Corporation
ii
VA903b-1_ VA903m-1
ViewSonic Corporation
VA903b-1_ VA903m-1
Taking out the monitor by grasping the LCD panel, that May causemura
ViewSonic Corporation
VA903b-1_ VA903m-1
Placing the monitor on a foreign objects, that could scratch The surface of the "Panel" or cause "mura"
ViewSonic Corporation
VA903b-1_ VA903m-1
2. Specification
INTRODUCTION
FEATURES Size Luminance (Typ) Contrast Ratio (Typ) 1 TFT LCD panel
st
VA903b-3 / VA903m-3 19 300 cd/ 700 :1 16.2 M colors (6+2bit panel) 8 ms 150 / 135 1280 x 1024 @60Hz Yes No Yes No No Yes Yes Yes Yes Under 36 W in max/32W IN TYP Saving mode< 2W Off mode <1 W Yes No No No Yes 416*429*210mm 485*503*163mm 4.6Kg / 10.12 lb 5.8Kg/ 12.76 lb 32~104 / 0~40 20 % - 90 % -4~140 / -20~60 5 % - 90 %
Colors Response Time (Typ) Viewing Angle (H/V) Recommend resolution Analog (75ohms, 1.0 Vp-p) Digital (DVI-D) Separate Sync Composite Sync Sync on Green PC
Input Signal
Sync Compatibility
Power Mac TV Box (NextVision 6) AC 100-240V, 50/60Hz On Mode(Max / Typ) Active Off Mode (Max) Tilt ( -5 - 22.5 )
Ergonomics
Swivel Pivot Height Adjust [ 1 ] [ 2 ] [ ][] [] Physical (W x H x D) Package (W x H x D) Physical (Net Weight) Package (Gross Weight) Temperature (/) Humidity (%) Temperature (/) Humidity (%)
Regulation
UL/cUL, FCC-B,TUV-S, CB, CE, TUV/GS, TUV/ERGO, TCO03, BSMI, CCC, (PSB), (C-TICK), GOST-R/HYGIENIC, SASO, WEEE, RoHS, ENERGY STAR,
ViewSonic Corporation
VA903b-1_ VA903m-1
Region
OSD Languages TFT LCD Panel and Model # Scalar Input Signal Sync Compatibility Audio Adapter Power Cable Analog Cable (1.8 m, color : black), with PC 2001 and
Hot Plug Detect &DDC
Audio Cable (1.8m, Color: black) with PC 2001 ViewSonic CD Wizard ViewSonic Quick Start Guide
Screen Protector Mylar Hi Pot label QA pass label Hg Warning label Warranty Sticker Warranty Card Carton Sticker PE bag of Carton
ViewSonic Corporation
VA903b-1_ VA903m-1
GENERAL specification Test Resolution & Frequency Test Image Size Contrast and Brightness Controls 1280 x 1024 @ 60Hz Full Size Factory Default: Contrast = 70%, Brightness = 100%
VIDEO INTERFACE Analog Input Connector Default Input Connector Video Cable Strain Relief Video Cable Connector DB-15 Pin out Video Signals Video Impedance Maximum PC Video Signal Maximum Mac Video Signal Sync Signals DDC 2B Sync Compatibility Video Compatibility Resolution Compatibility Exclusions POWER SUPPLY Internal Power Supply Input Voltage Range Input Frequency Range Short Circuit Protection Over Current Protection Leakage Current Efficiency Fuse Power Dissipation Max Input AC Current Inrush Current (Cold Start) Power Supply Cold Start Part Number: PI-SB03/ 100 - 240VAC
50/ 60 Hertz
DB-15 (Analog), refer the appendix A Defaults to the first detected input Equal to twice the weight of the monitor for five minutes Compliant DDC 2B Video RGB (Analog), Separate 75 Ohms (Analog) 950 mV with no damage to monitor 1250 mV with no damage to monitor TTL Compliant with Revision 1.3 Separate Sync Shall be compatible with all PC type computers, Macintosh computers, and after market video cards 640 x 350, 640 x 480, 720 x 400 (640 x 400), 800 x 600, 832 x 624, 1024 x 768, 1152 x 864, 1280 x 1024 Not compatible with interlaced video
90VAC,
@ 264 VAC
SHALL START AND FUNCTION PROPERLY WHEN UNDER FULL LOAD, WITH ALL COMBINATIONS OF INPUT VOLTAGE, INPUT FREQUENCY, AND OPERATING TEMPERATURE
Confidential - Do Not Copy
ViewSonic Corporation
VA903b-1_ VA903m-1
SHALL BE ABLE TO WITHSTAND AN ANSI/IEEE C62.41-1980 6000V 200 AMPERE RING WAVE TRANSIENT TEST WITH NO DAMAGE Shall be able to withstand 1.5 times nominal line voltage for one cycle with no damage Shall be able to function properly, without reset or visible screen artifacts, when cycle of AC power is randomly missing at nominal input The power supply shall not produce audible noise that would be detectable by the user. Audible shall define to be in compliance with ISO 7779 (DIN EN27779:1991) Noise measurements of machines acoustics. Power Switch noise shall not be considered Length = 1.8m. Connects to AC/DC Power Color = Black VESA DPMS Signaling ON Mode < 36 W (max) pOWER sAVING < 2W ,OFF < 1W On Mode = N/A, Active Off < 3 sec
US Type Power Cable Power Saving Operation (Method) Power Consumption Recovery Time ELECTRICAL REQUIREMENTS Horizontal / Vertical Frequency Horizontal Frequency Vertical Refresh Rate Maximum Pixel Clock Sync Polarity Timing Table Item 1 2 3 4 5 6 7 8 9 10 11 Timing 640 x 350 @ 70Hz, 31.5kHz 640 x 480 @ 50Hz, 24.68KHZ 640 x 480 @ 60Hz, 31.5kHz MAC 640 x 480 @ 67Hz, 35.0kHz 640 x 480 @ 72Hz, 37.9kHz 640 x 480 @ 75Hz, 37.5kHz 640 x 480 @ 85Hz, 43.27kHz 720 x 400 @ 70Hz, 31.5kHz 800 x 600 @ 56Hz, 35.1kHz 800 x 600 @ 60Hz, 37.9kHz 800 x 600 @ 72Hz, 48.1kHz
Analog Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
VA903b-1_ VA903m-1
ViewSonic Corporation
12 13 14 15 16 17 18 19 20 21 22 23 24 25
800 x 600 @ 75Hz, 46.9kHz 800 x 600 @ 85Hz, 53.7kHz MAC 832 x 624 @ 75Hz, 49.7kHz 1024 x 768 @ 60Hz, 48.4kHz 1024 x 768 @ 70Hz, 56.5kHz 1024 x 768 @ 72Hz, 58.1kHz 1024 x 768 @ 75Hz, 60.0kHz 1024 x 768 @ 85Hz, 68.67KHZ 1152 x 864 @ 75Hz, 67.5KHZ MAC 1152x870@75HZ, 68.68KHZ 1280 x 960 @ 60Hz, 44.93KHZ 1280 x 960 @75Hz, 56.25KHZ 1280 x 1024 @ 60Hz, 63.98KHZ 1280 x 1024 @ 75Hz, 79.97KHZ
Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
*1. Tolerance 2kHz. *2. Any timing not in the list, it should display as normal or show on OUT OF RANGE OSD message without blanking. *3. The image quality of 85Hz mode might be worse than 75Hz.
Primary Presets 1280 x 1024 @ 60Hz User Presets Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration Changing Modes Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding Auto Image Adjust time Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting when execute Auto Adjust The monitor needs to do Auto Image Adjust the first time a new mode is detected (See section 0-Touch Function Actions) The monitor needs to do Auto Adjust the first time a new mode is detected (See section 0-Touch Function Actions)
ViewSonic Corporation
VA903b-1_ VA903m-1
AUDIO INTERFACE (SPEAKER SPECIFICATION) (For VA903m-3 only) Line input connection Line input signal Line input impedance Maximum power output (Electric) Signal to Noise Ratio Frequency response Distortion Vibration Screen image Connector PC99 requirement Audio in Cable type / length Audio DPMS
3.5 mm stereo jack
1.0Vrms >10 kOhm 1 W @ <15% DISTORTION 50 dB 200 Hz 20 Khz <15% THD (@1kHz) There should be no audible vibration with volume at 100%. (Input signal within 1.0 Vrms) There should be no affect on the screen image stability under any conditions
Lime Green pantone # 577C
3.5mm stereo cable / 1.8m length NOTE: THERE IS NO GUARANTEE <1 W POWER CONSUMPTION IN ACTIVE OFF MODE, WHEN THE AUDIO CABLE IS CONNECTED
TFT LCD PANEL 1st Panel Source HSD 190ME13-A16/A10 TN, LVDS 376.32 mm (H) x 301.056mm (V) RGB Vertical Stripe 0.294 mm ANTI GLARE (HARD COATING 3H) 4 CCFL EDGE-LIGHT 50,000 HOURS (MAX) / 40,000 HOURS (MIN) 300 CD/M2 (TYP AFTER 30 MINUTE WARM UP) 240 CD/M2 (MIN AFTER 30 MINUTE WARM UP) 75 % (min) 700 :1 (Typ), 450 :1 (Min) 16.2 million colors (6+2 bit panel) 150 deg (Typ)@ CR>10 160 deg (Typ)@ CR>5 135 deg (Typ) @ CR>10 150 deg (Typ)@ CR>5 8 ms (Tr= 2 ms, Tf = 6 ms) (Typ) 12 ms (Tr= 4 ms, Tf = 8 ms) (max) Please see Panel Quality Specifications.
Confidential - Do Not Copy
Type Active Size Pixel Arrangement Pixel Pitch Glass Treatment # of Backlights Backlight Life Luminance Condition: CT = 6500 K Contrast = Max, Brightness = Max Brightness Uniformity Contrast Ratio Color Depth Vertical) Viewing Angle (Horizontal) Viewing Angle (Vertical) Response Time 10%-90% @ Ta=25C Panel Defects ViewSonic Corporation
VA903b-1_ VA903m-1
IMAGE PERFORMANCE Display Size Horizontal Display Size, Primary Preset Vertical Display Size, Primary Preset Luminance Lv (Max) Condition:
Brightness / Contrast = 100% CCT = USER COLOR (R/G/B=100%)
Lv (6500Kf) Condition:
Brightness / Contrast = Default Color Temperature = 6500K
Lv (sRGB) Condition:
Brightness / Contrast = Default CCT =sRGB
Lv (9300K) Condition:
Brightness / Contrast = Default CCT = 9300K
Lv (5400K) Condition:
Brightness / Contrast = Default CCT = 5400K
Lv (Brightness) Condition:
Contrast = 100%
Lv (Contrast) Condition:
Brightness = 100%
CR(6500K) Condition:
Contrast / Brightness = 100% CCT = 6500K
Saturation Contrast = Default Brightness = Default Test pattern = 64-gray Contrast = 100% Brightness = 100% Test pattern = 64-gray ViewSonic Corporation NO VISIBLE SATURATION
10
VA903b-1_ VA903m-1
Contrast = 100% Brightness = 100% Input signal level = 720mV Test pattern = 64-gray Preset Color Temperatures sRGB Preset 1
It should meet IEC 61966-2-1 (1999-10) standard. CCT (typ) = 9300K (uCCT=0.1888; v CCT=0.4457) CCT (max) = 10250K, CCT (min) = 8500K uv<0.01 (@ Full White pattern)
Preset 2 (Primary)
CCT (typ) = 6500K (uCCT=0.1978; v CCT=0.4684) CCT (max) = 6950K, CCT (min) = 6100K uv<0.01 (@ Full White pattern)
Preset 3
CCT (typ) = 5400K (uCCT=0.2044; v CCT=0.4808) CCT (max) = 6185K, CCT (min) = 4935K uv<0.01 (@ Full White pattern)
Each color preset shall be adjustable. and Blue shall be individually controlled.
Red, Green,
Video Cards Compatibility Peaking Performance: Peaking is not adjustable Raster Artifacts Video Artifacts : No visible streaking, sag, or smearing artifacts when driven by the specified video cards in the primary mode and after user adjustment to best condition Power Supply, and Grounding Artifacts : No visible artifacts in any specified video mode within the horizontal or vertical frequency range of the monitor Temperature Drift : Image shall not drift or lose fine-tune adjustment
ViewSonic Corporation
11
VA903b-1_ VA903m-1
MECHANICAL Dimension Dimension (Desktop) Width Height (Height adjust to the bottom) Depth Monitor Weight *Refer to Figure 1 Dimension (Head Only / Wall Mount) Width Height Depth Monitor Weight *Refer to Figure 1 Ergonomics Tilt Up step 1 Tilt Down Swivel Right Swivel Left Height Adjust Pivot 0 TO 20.53 From 0 down to -5 N/A N/A N/A N/A 416mm 364mm 68mm 4.2KG / 9.25lb 416mm 429mm 210mm 4.6KG / 10.12lb
ViewSonic Corporation
12
VA903b-1_ VA903m-1
[1] + [] + [] White Balance (Not shown on users guide) (keep pushing 5 sec) [1] + [] Power Lock [1] + [] OSD Lock Remark : All the short cuts function are only available while OSD off Front Panel Hardware Controls Power Switch (Front Head) Power Control, soft Power Switch. Green On / Orange Active Off Power LED (Front Head) Dark = Soft Power Switch OFF [ ] Power [ 1 ] BUTTON 1 [ 2 ] Button 2 [] UP ARROW BUTTON Front Panel Controls (Head) [] DOWN ARROW BUTTON [ 1 ] [ 2 ] [ ][] [] Note: Power Button, Button 1 and Button 2 must be one-shot logic operation. (i.e. there should be no cycling) Reaction Time OSD must fully appear within 0.5s after pushing [ 1 ] Main Menu Controls Auto Image Adjust Contrast/Brightness*1 Audio Adjust (For VA903m-3 only) Volume*3, Mute*3 Color Adjust sRGB, 9300K, 6500K(default), 5400, User Color [R, G, B] Information H Frequency, V Frequency, Pixel Clock, Resolution, Serial Number, Model Number, www.ViewSonic.com Manual Image Adjust H. Size, H/V Position, Fine Tune, Sharpness*2 Setup Menu Language [English, French, German, Italian, Spanish, Finnish, Simplified Chinese Traditional Chinese, Japanese], Resolution Notice, OSD Position*1, OSD Timeout, OSD Background Memory Recall *1 These functions can be recalled to default by []+ [] *2 These functions are not available under Native Resolution Mode *3 These functions setting can be recalled to default by []+[] under audio mode [Remark] Please refer to the detail in the Appendix C
ViewSonic Corporation
13
VA903b-1_ VA903m-1
Function descriptions OSD Lock short cuts function for the buttons The OSD lock will be activated by pressing the front panel control buttons "(1), & ()" for 10 seconds. If the user then tries to access the OSD by pressing any of the buttons "1", "", "", "2" a message will appear on the screen for 3 seconds showing "OSD Locked". The OSD lock will be deactivated by pressing the front panel control buttons "(1), & ()" again for 10 seconds. Note1: When the OSD is locked will lock all functions, including Volume and Mute Note 2: Status bar indicating OSD Lock or Unlock is in progress and when complete it will indicate OSD Locked Note 3: OSD Lock should not lock Power Button and Power Lock function Power Lock short cuts function for the buttons The power button lock will be activated by pressing the front panel control buttons "(1), & ()" for 10 seconds. Locking the power button means that the user won't be able to turn off the LCD while the power button is locked. If the user presses the power button while it is locked, a message will appear on the screen for 3 seconds showing "Power Button Locked". It also means that with the power button locked, the LCD would automatically turn back "On" when power is restored after a power failure. If the power button is not in the locked mode, then power should return to it's previous state when power is restored after a power failure. The power button lock will be deactivated by pressing the front panel control buttons "(1), & ()" again for 10 seconds Note 1: Status bar indicating Power Button lock or unlock is in progress and when complete it will indicate Power Button Locked
Note 2: Power should only be lockable in the On State
Memory Recall Actions Memory Recall action on the analog and digital mode as below 1. Set the factory defaults as shown in Section 4-7 2. Clean all the mode setting buffer 3. Execute Auto Image Adjust
Note: Memory Recall should have no effect for Language, Power Lock, User Color Settings
Resolution Notice Actions 1. Resolution Notice OSD should show on screen after changing to non-native mode for 30 sec 2. The OSD should disappear after 10 sec or by pushing button [1] or [2] Resolution Notice function should be disabled when push button [2] under Resolution Notice OSD 0-Touch Function Actions 1. Execute Auto Image Adjust when new mode detected, and save the settings to buffer for further use 2. It should be reset by Memory Recall function (Should not reset by power off, power unplug and others) OSD Auto Save The OSD shall save new settings when it is turned off by the user or when it times out. There shall not be a separate save
ViewSonic Corporation
14
VA903b-1_ VA903m-1
Factory Defaults Item Contrast Brightness Color Temperature Sharpness OSD H. Position OSD V. Position Defaults 70% 100% 6500K 0% 50% 50% Item Volume Balance Treble Bass 720x400/640x400 640x480@60Hz 720x480@60Hz Defaults 50% (For VA903m-3 only) N/A N/A N/A 720x400 640x480@60Hz
15 Sec
In SOG and Composite, 720x480@60Hz N/A 640x480@60Hz In SOG and Composite, 1152x864@75Hz N/A 1152x870@75Hz In SOG and Composite, 1280x768@60/75/85Hz N/A 1024x768@60/75/85Hz
OSD Background
Enabled
Resolution Notice
Enabled
AUDIO INTERFACE (SPEAKER SPECIFICATION) (For VA903m-3 only) Line input connection Line input signal Line input impedance Maximum power output (Electric) Signal to Noise Ratio Frequency response Distortion Vibration Screen image Connector PC99 requirement Audio in Cable type / length Audio DPMS 3.5 mm stereo jack 1.0Vrms >10 kOhm 1 W @ <15% distortion 50 dB 200 Hz 20 Khz <15% THD (@1kHz) There should be no audible vibration with volume at 100%. (Input signal within 1.0 Vrms) There should be no affect on the screen image stability under any conditions Lime Green pantone # 577C 3.5mm stereo cable / 1.8m length Note: There is no guarantee <1 W power consumption in Active Off mode, when the Audio Cable is connected
ViewSonic Corporation
15
VA903b-1_ VA903m-1
4. Circuit Description
A. AC-DC CONVERTER The power supply with a high-integrated green-mode PWM controller provides several features to enhance the performance of power flyback converters. U801 is a PWM controller and provides many protection functions. U802 is a photo couple to transfer the feedback signal from the second side which U803 detected both of the output DC voltage on 5V and 24V. Z802 detected the working voltage on U801 and Q802 would pull down the voltage on U801 pin5 to shut down U801 if feedback loop was failed. R828 would be a dynamic load which was active while backlight was turned off and system still working on, this kept 24V output voltage under 32V to protect the panel. After system went to power saving mode, the R828 would no loaded. This was detected by Z803 active the R828 to load or not. BScaling Controller
Overview
Realtek RTD2523B series products are all-in-one LCD monitor controllers support up to SXGA/XGA(optional), and integrate Realtek high performance ADC, TMDS Rx(optional), scaling engine, OSD engine, LVDS TX, RSDS TX and so on. Moreover, all products are pin compatible in low pin count package to save cost and make the design easier
General
Embedded dual DDC support DDC1, DDC2B, DDC/CI Zoom scaling up and down Embedded Pattern Generator No external memory required. Require only one crystal to generate all timing Embedded reset control output Embedded crystal output to MICROP 3 channels 8 bits PWM output, and selectable PWM clock frequency.
Pin Description (I/O Legend: A = Analog, I = Input, O = Output, P = Power, G = Ground) ADC: 15 pins
Name I/O AG AP AP AI AI AG AIO AI AI AP AI ADC_GND ADC_REFIO ADC_VDD BLUE+ BLUEADC_GND SOG/ADC_TEST GREEN+ GREENADCB_VDD RED+
Pin No 27 28 29 30 31 32 33 34 35 36 37
Description ADC ground ADC band-gap voltage de-coupling Analog power Analog input from BLUE channel Analog input ground from BLUE channel ADC ground SOG in/ADC test pin Analog input from GREEN channel Analog input ground from GREEN channel Analog power Analog input from RED channel 1.20V (3.3V)
Note
(3.3V)
ViewSonic Corporation
16
VA903b-1_ VA903m-1
AI AG AG AP AI AI
38 39 40 41 42 43
Analog input ground from RED channel Analog ground Analog ground Analog power Analog HS input Analog VS input
PLL: 8 pins
Name I/O AI AO AG AP AP AIO AIO AG XO XI DPLL_GND DPLL_VDD APLL_VDD PLL_TEST1 PLL_TEST2 APLL_GND
Pin No 1 2 3 4 5 6 7 8
Description Reference clock output Reference clock input Ground for digital PLL Power for digital PLL Power for multi-phase PLL Test Pin 1 / IRQ# Test Pin 2/Power-on-latch for crystal out Frequency Ground for multi-phase PLL
Note
(3.3V) (3.3V)
ViewSonic Corporation
17
VA903b-1_ VA903m-1
53
S[1] / TCON[4]
S[1] / TCON[4] PWM2 / COUT / TCON[13] BB3P BB3N BB2P BB2N BB1P BB1N BCLKP BCLKN BG3P BG3N BG2P BG2N BG1P BG1N BR3P BR3N BR2P BR2N BR1P BR1N NC NC NC NC NC NC NC NC NC NC TCON [11] TCON [10] TCON [9] TCON [8] TCON [7]
S[1] / TCON[4] PWM2 / COUT / TCON[13] NC NC NC NC NC NC NC NC NC NC TODP TODN TOCLKP TOCLKN TOCP TOCN TOBP TOBP TOAP TOAP TEDP TEDN TECLKP TECLKN TECP TECN TEBP TEBN TEAP TEAN NC NC NC NC NC
S[1]/ BBLU[0] / TCON[4] PWM2 / COUT / TCON[13] BBLU [7] BBLU [6] BBLU [5] BBLU [4] BBLU [3]/T0 BBLU [2]/T1 BGRN [1]/T2 BGRN [0]/T3 BGRN [7] BGRN [6] BGRN [5]/T4 BGRN [4]/T5 BGRN [3]/T6 BGRN [2]/T7 BRED [7]/T8 BRED [6]/T9 BRED [5]/T10 BRED [4]/T11 BRED [3]/T12 BRED [2]/T13 ABLU [7]/T14 ABLU [6]/T15 ABLU [5]/T16 ABLU [4]/T17 ABLU [3]/T18 ABLU [2]/T19 ABLU [1]/T20 ABLU [0]/T21 AGRN [7]/T22 AGRN [6]/T23 AGRN [5]/T24 AGRN [4]/T25 AGRN [3]/T26 AGRN [2]/T27 ARED [7]/T28
S[1] / TCON[4] PWM2 / COUT / TCON[13] BBLU [7] BBLU [6] BBLU [5] BBLU [4] BBLU [3] BBLU [2] TCON [6] TCON [5] BGRN [7] BGRN [6] BGRN [5] BGRN [4] BGRN [3] BGRN [2] BRED [7] BRED [6] BRED [5] BRED [4] BRED [3] BRED [2] ABLU [7] ABLU [6] ABLU [5] ABLU [4] ABLU [3] ABLU [2] TCON [1] TCON [0] AGRN [7] AGRN [6] AGRN [5] AGRN [4] AGRN [3] AGRN [2] ARED [7]
55
BB3P BB3N BB2P BB2N BB1P BB1N BCLKP BCLKN BG3P BG3N BG2P BG2N BG1P BG1N BR3P BR3N BR2P BR2N BR1P BR1N AB3P AB3N AB2P AB2N AB1P AB1N ACLKP ACLKN AG3P AG3N AG2P AG2N AG1P AG1N AR3P
ViewSonic Corporation
18
VA903b-1_ VA903m-1
TCON [6] TCON [5] TCON [1] TCON [0] NC PWM2 / COUT / TCON[12] V [0]
ARED [6]/T29 ARED [5]/TH ARED [4]/TV ARED [3]/TE ARED [2]/TK ARED [1]
ARED [6] ARED [5] ARED [4] ARED [3] ARED [2] PWM2 / COUT / TCON[12] (9)
114
ARED [0]
TCON [11]
115
V [1]
V [1]
BRED [1]
TCON [10]
116
V [2]
V [2]
BRED [0]
TCON [9]
117
V [3]
V [3]
AGRN [1]
TCON [8]
118
V [4]
V [4]
AGRN [0]
TCON [7]
119
V [5]
V [5]
DHS
DHS
122
V [6]
V [6]
DVS
DVS
123
V [7]
V [7]
DENA
DENA
124
VCLK
VCLK
DCLK / TCLK
DCLK / TCLK
TMDS: 18 pins
Name TMDS_TST/ PWM1 I/O AIO Pin No 9 Description TMDS_TEST Pin / PWM1 / Power-on-latch for serial / parallel port TMDS_GND TMDS_VDD EXT_RES TMDS_VDD RX2P RX2N TMDS_GND RX1P RX1N G P A P I I G I I 10 11 12 13 14 15 16 17 18 Differential Data Input Differential Data Input VA903b-1_ VA903m-1 Differential Data Input Differential Data Input Impedance Match Reference. (3.3V) (3.3V) Note
ViewSonic Corporation
19
P I I G I I G P
19 20 21 22 23 24 25 26 Differential Data Input Differential Data Input Differential Data Input Differential Data Input
(3.3V)
(3.3V)
PWM Interface: 3-2=1 pin (PWM1, PWM2 can be selected from 1 of 3 possible pins.)
Name PWM2 / TCON [2] / S [3] PWM2 / TCON [13] / COUT PWM2 / TCON [12] / COUT PWM1 / TMDS_TST AIO 9 PWM1/ TMDS_TEST Pin / Power-on-latch for serial / parallel port PWM1 / DDCSDA / TCON [1] / BBLU [0] PWM1 / DDCSDA2 (HDCP) / TCON [7] PWM0 / REFCLK IO 112 IO 125 IO 47 PWM1 / DDC serial control I/F data input / output / TCON [4] PWM1 / DDC serial control I/F data input / output / TCON [7] PWM0 / (In / out) test pin for DCLK / Video8 even-odd signal (2), (9) (1), (2), (3), (5), (8), (1), (2), (3), (5), (8), (2), (7), (8) O 113 PWM2 / TCON [12] / Crystal out (2), (8), (9) O 55 PWM2 / TCON [13] / Crystal out (2), (8), (9) I/O O Pin No 51 Description PWM2 / TCON [2] / SDIO [3] Note (1), (2), (3), (5), (8),
Description
ViewSonic Corporation
20
VA903b-1_ VA903m-1
3.3V Ground G 48,120 GNDIO: 2 3.3V Power P 58,71,83,95,110 PVCC: 5 3.3V Ground G 57,72,84,96,109 PGND: 5 2.5V Power P 45,69,98,127 VCCK: 4 2.5V Ground G 44,70,97,128 GNDIK: 4 Note: (1) TTL compatible CMOS Input (Vt=1.7V); VCC=3.3V; (2) 5V tolerance pad; (3) Internal 75K Ohms pull high resistor. (4) Internal 75K Ohms pull low resistor. (5) Schmitt trigger CMOS Input (Vt=1.4-~2.2V); (6) Open-Drain, Output Drive low & Pull-high. (7) Bi-directional input/output (8) Programmable driving current (2~10mA) (9) TTL output 5V & 3.3V (10) 4V tolerance pad C, MTV512M The MTV512M micro-controller is an 8051 CPU core embedded device especially tailored for flat panel display applications. It includes an 8051 CPU core, 768-byte SRAM, 4 channels of 6-bit ADC, 3 external counters/timers, 6 channels of PWM DAC, VESA DDC interface, and a 64K-byte internal program Flash-ROM memory in 44-pin PLCC package FEATURES 8051 core, 12MHz operating frequency with single/double CPU clock option 0.35um process; 3.3V power supply 768-byte RAM; 64K-byte program Flash memory Maximum 6 channels of PWM DAC Compliant with VESA DDC1/2B/2Bi/2B+ standard Dual slave IIC addresses; two H/W auto transfer DDC1/DDC2x data for both D-sub and DVI interfaces Watchdog timer with programmable interval Support external counters/timers, 1 & 2 Single/double frequency clock output Two external interrupts, INT1 is shared with Slave IIC interrupt source. Maximum 4 channels of 6-bit ADC Flash-ROM code protection selection 44-pin PLCC package D. INVERTER In order to drive the CCFLs embedded in the panel module, there is a push-pull inverter to convert by the controller. from input 24V up to hundreds of AC voltage output peak to peak. The inverter is formed by symmetric in order to drive the separate lamp modules. The input stage consists of a PWM controller, push-pull inverter, and switching MOSFET to convert DC input into
ViewSonic Corporation
21
VA903b-1_ VA903m-1
AC output. The output stage consists of a tuning capacitor, transformer, and push-pull MOSFET pair to boost AC output up to hundreds of voltage peak to peak. And one resister is serial to lamp for output voltage feedback. There are two signals which control the inverter come from system to turn on the inverter and control brightness. Logic low level which send to U901 is turn on the inverter. BL-ADJ signal control brightness by DC level which was integral from PWM signal.
ViewSonic Corporation
22
VA903b-1_ VA903m-1
5. Adjusting Procedure
1. Function test 1.1 products 19 LCD Monitor 1.2 test equipment Color video Signal& pattern (Or PC with SXGA resolution and a sound card) 1.3 Test Condition Before function test and alignment ,each LCD Monitor should be warmed up at least 30 minutes with the following conditions: A: in roon temperature B with full white screen ,RGB ,and black C. with cycled display model: 1280 x 1024 @ 60Hz 1.4 Test display& Pattern 1.4.1 Compatible model
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 *1. Tolerance Timing 640 x 350 @ 70Hz, 31.5kHz 640 x 480 @ 50Hz, 24.68KHZ 640 x 480 @ 60Hz, 31.5kHz MAC 640 x 480 @ 67Hz, 35.0kHz 640 x 480 @ 72Hz, 37.9kHz 640 x 480 @ 75Hz, 37.5kHz 640 x 480 @ 85Hz, 43.27kHz 720 x 400 @ 70Hz, 31.5kHz 800 x 600 @ 56Hz, 35.1kHz 800 x 600 @ 60Hz, 37.9kHz 800 x 600 @ 72Hz, 48.1kHz 800 x 600 @ 75Hz, 46.9kHz 800 x 600 @ 85Hz, 53.7kHz MAC 832 x 624 @ 75Hz, 49.7kHz 1024 x 768 @ 60Hz, 48.4kHz 1024 x 768 @ 70Hz, 56.5kHz 1024 x 768 @ 72Hz, 58.1kHz 1024 x 768 @ 75Hz, 60.0kHz 1024 x 768 @ 85Hz, 68.67KHZ 1152 x 864 @ 75Hz, 67.5KHZ MAC 1152x870@75HZ, 68.68KHZ 1280 x 960 @ 60Hz, 44.93KHZ 1280 x 960 @75Hz, 56.25KHZ 1280 x 1024 @ 60Hz, 63.98KHZ 1280 x 1024 @ 75Hz, 79.97KHZ 2kHz. Analog Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
*2. Any timing not in the list, it should display as normal or show on OUT OF RANGE OSD message without blanking. *3. The image quality of 85Hz mode might be worse than 75Hz.
ViewSonic Corporation
23
VA903b-1_ VA903m-1
ViewSonic Corporation
24
VA903b-1_ VA903m-1
ViewSonic Corporation
25
VA903b-1_ VA903m-1
METHOD A B
LPT PORT
TEST PC
Fixture ISP_CORD
Fixture POWER_ADAPTER
ViewSonic Corporation
26
VA903b-1_ VA903m-1
LPT Cable
AC power Cable
VGA Cable
ISP3.0 SOFT
2.2. Setup Procedure 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 Connect PO1 of ISP fixture with print port of computer by LPT cable Connect PO2 of ISP fixture with USB port of computer by USB cable Connect PO3 of ISP fixture with monitor VGA port by VGA cable Connect mouse, keyboard, AC power, monitor with computer Plug AC cable in power adapter AC jack Connect power adapter DC_OUTPUT port to main board DC_IN port Connect PO3 of ISP fixture with VGA port of monitors main board by VGA cable
ViewSonic Corporation
27
VA903b-1_ VA903m-1
jumper
AC JACK
DC_IN port
VGA port
NOTE: Do STEP2.2.6 and STEP2.2.7 for monitors main board only. Monitor firmware upgrade will jump this step.
ViewSonic Corporation
28
VA903b-1_ VA903m-1
2.3. Soft install Install ISP3.0 program by selecting and clicking \isp3.0\setup.exe, press YES or NEXT buttons until setup is complete.
ViewSonic Corporation
29
VA903b-1_ VA903m-1
ViewSonic Corporation
30
VA903b-1_ VA903m-1
ViewSonic Corporation
31
VA903b-1_ VA903m-1
ViewSonic Corporation
32
VA903b-1_ VA903m-1
STEP1: Choose the DCC written Program set up the DCC written fixture ,check whether the connection between main board is in well condition ,see attached file 1.1&1.2 per the product model ,choose the corresponding Model, DCC written process, the model mr171-AAA should apply the SIP Program
ViewSonic Corporation
33
VA903b-1_ VA903m-1
STEP2: Creat security file Choose the Tab "create Security File " to enter next Dialogue Item
ViewSonic Corporation
34
VA903b-1_ VA903m-1
STEP3: Input the related parameter, save them and take up the next step
STEP4: Choose the Tab MTV TYPE Choose the MTV512M64 from the TAB ISP ITEMS
ViewSonic Corporation
35
VA903b-1_ VA903m-1
ViewSonic Corporation
36
VA903b-1_ VA903m-1
SETP6: Choose the DDC Written BIOS document Choose the Tab LOAD MCU FILELooking up the related BIOS document in my Computer ,and Point the confirm Tab
when the BIOS Documents' loading is successful ,you can find the picture as above
ViewSonic Corporation
37
VA903b-1_ VA903m-1
Step 7.Confirm the BIOS'S check sum In the above attached Display picture ,you should check whether the check sum's Data comply to the bios' DCC written, if there is no problem ,pls press the run menu to write
If showed the picture as above pls check whether the DDC write fixture is well Connected with PC the power board is power on and the program's setup is all right
ViewSonic Corporation
38
VA903b-1_ VA903m-1
ViewSonic Corporation
39
VA903b-1_ VA903m-1
Disassembly Procedure
1. Remove the hinge cover
ViewSonic Corporation
40
VA903b-1_ VA903m-1
5. Tear off the aluminum foil where cover the FFC cable,take out the key board from bezel ,pull out
6. pull out the two pcs screw form the main board
ViewSonic Corporation
41
VA903b-1_ VA903m-1
7. pull out the two screws where lie in the two sides of the frame
8. pull out the screws which fix up the bezel and then take out the bezel
ViewSonic Corporation
42
VA903b-1_ VA903m-1
11. take out the screw form the power board ,pull out the power boards connecter wire
12. take out the FCC Cable AL where lies in the panel ,pull out the FCC cable
ViewSonic Corporation
43
VA903b-1_ VA903m-1
ViewSonic Corporation
44
VA903b-1_ VA903m-1
Packing Procedure 1.1 Paste production film to protect the monitor screen.(Figure 1) tape Production film
1.2 Put the monitor in the PE bag and seal bag with type (Figure 2) tape
ViewSonic Corporation
45
VA903b-1_ VA903m-1
1.4 Put the base in the EPE bag. and then,place the base on the cushions ,as figure;
1.4.Place the monitor into the carton and then put all accessories into carton .At last,close the carton.
Use s Guide
Power cord
Base
signal cord
ViewSonic Corporation
46
VA903b-1_ VA903m-1
Power On
No
Yes
ViewSonic Corporation
47
VA903b-1_ VA903m-1
Is backlight on?
No
B. Backlight Troubleshooting
Yes
No
C. Performance Troubleshooting
No
D. Function Troubleshooting
No
E. Audio Troubleshooting
No Trouble Found
End
ViewSonic Corporation
48
VA903b-1_ VA903m-1
End
End
No Trouble Found
End
ViewSonic Corporation
49
VA903b-1_ VA903m-1
B. Backlight Troubleshooting
Start
End
End
End
No Trouble Found
End
ViewSonic Corporation
50
VA903b-1_ VA903m-1
C. Performance Troubleshooting
Start
Screen is scrolling?
Yes
No
NO
Screen is flickering?
YES
NO
NO
YES
NO
YES
YES
YES NO
Bad Uniformity?
YES
NO
Is screen white?
YES
Check Connector
NO
YES
YES
NO
ViewSonic Corporation
51
VA903b-1_ VA903m-1
Yes
Yes
End
No
Screen is smaller?
Yes
No
Yes
Reset O.K.?
No
No
Yes
No Trouble Found
End
ViewSonic Corporation
52
VA903b-1_ VA903m-1
D. Function Troubleshooting
Start
No
No
Yes
End
ViewSonic Corporation
53
VA903b-1_ VA903m-1
E. Audio Troubleshooting
Start
No Sound
Yes
Change Speaker
No
Sound is broken?
Yes
Change Speaker
No
Volume Unadjustable?
Yes
No
No Trouble Found
End
ViewSonic Corporation
54
VA903b-1_ VA903m-1
Cabinets:
Added on 10/02/06
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items. Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Cabinets:
Added on 10/02/06
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items. Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
ViewSonic Corporation
55
VA903b-1_ VA903m-1
ViewSonic Corporation
56
VA903b-1_ VA903m-1
Item 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131
ViewSonic P/N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A B-00006502 N/A N/A N/A N/A C-00008154 N/A PL-00006589 C-00008155 N/A N/A N/A N/A N/A HW-00008014 N/A N/A N/A N/A CB-00005758 N/A N/A N/A
Ref. P/N C4022296M2122 C02410302K111 C02410403K111 C02447302K111 C02447401K111 C4021006M2431 C4021014M2222 C4022204M2322 C4024704M2422 D00BAV9905G01 D00L414803Y11 D01ZT52C03K01 E231080150009 J4507270155B1 J4509100102H1 J4509100306H1 L004100201101 L013121302A11 Q441240047151 R070000J10311 R070000J20111 R070331J10111 R070470J10111 R070750J10111 R071000J10111 R074702J20111 R070059J61111 R071001J20111 R071002J20111 R071003J10111 R071004J30111 R071502F30111 R072001J30111 R072200J20111 R073002J10111 R074701J20111 R076801J10111 R144701J20112 T00T390402G01 T00T390602G01 T01A340102A21 Y640307001*1 Y64115HB06*1 XLM191A050001 BLM191AB10113 D462102211201 J4509100102H1 P764P295LM010 XLM191A100002 P727A901LMC60-C P763P398LM020-B XLM191A110002 M105223004401 M410810130001 M627700LM0270-E P728A995LM130-A V300800000001 XLM191A200002 M155234008401 M155234010401 M701900LM0190-K P711A995LM030-A W0026918A0142 P392411A00001 Y64115HB04*1 L012121201113
Description Location CAP EC -40~105 2.2uF/25V 20%(M) 4*H5mm P=2.0mm (DIP) CAP MLCC X7R 10nF/25V10%(K) 0603TAPPING (SMD) CAP MLCC X7R 0.1UF/50V 10%(K) 0603 TAPPING(SMD) CAP MLCC/ X7R 0.047uF /25V 10%(K) 0603 TAPPING(SMD) CAP MLCC X7R 470nf 16V 10%(K) 0603 TAPING lead free (SMD) CAP EC(S) -40~105 10uF 25V 20% (M) 5H7mm P=2.5mm (DIP) CAP EC(S) -40~105 100uF 16V 20% (M) 5H11mm P=2.0mm (DIP) CAP EC -40~105 22UF/16V 20%(M) 5*H5MM P=2.0MM (DIP) CAP EC -40~105 47UF/16V 20% (M) 5*H7MM P=2.0MM (DIP) DIODE BAV99 SOT-23 GTM (SMD) DIODE LL4148 SOD-123 YING SMD DIODE BZT52C SOD-123 KINGWELL 5.6V (SMD) SPEAKER 3717CP15 OBLONG 8 1.5W R/L450mm L37*W17*H9mm Y&G LEAD FREE D-SUB H/D,15PIN,VGA PC99(LIGHT BLUE)DIP 90,3 ROW,1285-15S-004-98C01,TEKCON FFC CONNECTOR P=1mm 10PIN 90 CF16061D0T0 HANQUAN (DIP) FFC CONN ,30 PIN,1.0,DIP 180,1 ROW,Cvilux 16301V0T or compatible BEAD Chip Beads DDY160808U011MB 10 200mA 0603(1608) TAPING MAGIC LEAD FREE (SMD) CHIP BEAD Ferrite ChipBeads (high current) WB201209B601QLT02 120 3000mA 1206 Walsin (SMD) CRYSTAL QUARTZ/ 24MHZ 30PPM 20PF 49US CRE (DIP) RES CHIP 0 5%(J) 1/10W 0805 TAPPING (SMD)(Y180320000J0) 05: RESISTOR.RES CHIP 0 5%(J).1/8W 0603 TAPPING (SMD)...... RES CHIP 330 5%(J) 1/10 0603 TAPPING (SMD) RESISTOR.RES CHIP 475%(J) 1/10W.0603 TAPPING (SMD) RESISTOR.RES CHIP 75 5%(J) 1/10W.0603 TAPPING (SMD)...... RES CHIP 100 5%(J) 1/10 0603 TAPPING (SMD) 05: RESISTOR.RES CHIP 47K 5%(J) 1/8W.0603 TAPPING (SMD)...... RES CHIP 0.5 5%(J) 1/2W 1210 TAPING LEAD FREE (SMD) 05: RESISTOR.RES CHIP 1K 5%(J) 1/8W.0603 TAPPING (SMD)...... 05: RESISTOR.RES CHIP 10K 5%(J) 1/8W.0603 TAPPING(SMD)...... RES CHIP 100K 5%(J) 1/1 0603 TAPPING (SMD) RES CHIP 1M 5%(J) 1/16W 0603 TAPPING (SMD) RES CHIP 15K 1%(F) 1/16 0603 TAPPING (SMD) RES CHIP 2K 5%(J) 1/16W 0603 TAPPING SMD)(Y180222001J0) 05: RESISTOR.RES CHIP 220 5%(J) 1/8W.0603 TAPPING(SMD)...... 05: RESISTOR.RES CHIP 30K5%(J) 1/10W.0603 TAPPING (SMD)...... RESISTOR.RES CHIP 4.7K 5%(J) 1/8W.0603 TAPPING(SMD)...... RES CHIP 6.8K 5%(J)1/10W 0603 TAPING (SMD) RES ARRAY 4.7K 5%(J) 1/10W 8P4R 3216 TAPPING (SMD) TR GMBT3904 SOT-23 GTM (SMD) TR GMBT3906 SOT-23 GTM (SMD) XSTR AO3401/ST3401, SOT- 23;3 , Alpha & Omega/ST JACK PHONE EAR (TJ312-5BP- 1) CONNECTOR 180 2mm 6PIN KEY BOARD ASSY LM/MR19I-AAA BARE PCB LM/MR19I-AAA BUTTON BOARD 1SIDE FR-1 T1.6mm REV:1.3 LED,3.0x5.3 mmP=2.54 YELLOW/GREEN (DIP) FFC CONNECTOR P=1mm 10PIN 90 CF16061D0T0 HANQUAN (DIP) SWITCH PA66 BLACK LCDMONITOR SERIES REV:0 BEZEL ASSY(SILVER ) LM/MR19I-AAA BEZEL+BTTTON BEZEL ABS HB SILVER PRINT LM/MR19I-AAA REV:0 FUNCTION BUTTON PC SILVER PAINT LM/MR17I-AAA REV:0(GAOCHENG ) HOUSING ASSY(BLACK) LM/MR19I-AAA RGB+AUDIO MACHINE SCREW Bouding 3.0*L6mm NICKEL SCREW 4.0*L8mm NICKEL WITH WASHER Holder SECC LM/MR19I- AA L114*W67.75*H8.1*T1.5mm REV:0 HOUSING ABS HB BLACK Shoot shaping LM/MR19I-AAA RGB+AUDIO REV:0 GLUE 50g/BOTTLE (-60~+200) BRACKET ASSY(black) LM/MR19I-AAA bracket+hinge+screw(GAOCHENG ) SCREW plastics,be attacked Low carbon steel /PW4.0*L8mm NICKEL SCREWplastics,be attacked Low carbon steel /PW4.0*L10mm NICKEL SCREW 4.0*L8mm NICKEL WITH WASHER Bracket ABS HB BLACK Shoot shaping LM/MR17I-AAA REV:0(GAOCHENG ) AUDIO CABIE 26AWG UL2547 L=1800mm 6C BLACK SPEAKER SPONGE L24.5*W11*T10mm L/R 25(VA703) CONNECTOR M 180/2.0mm 1 ROW 4P BEAD CHOKE Ferrite(generalcircuit) DDY160808U121MB 120 200mA 0603DUANWANG LEAD FREE (SMD)
Universal number#
Q'ty 1 35 6 1 3 5 2 1 3 4 6 1 1 1 1 3 5 2 2 6 2 3 3 10 5 1 9 5 1 1 2 3 8 1 9 2 6 3 4 1 1 1 1 1 1 1 5 1 1 1 1 2 4 2 1 0.01 1 1 2 1 1 1 4 1 1 9
ViewSonic Corporation
57
VA903b-1_ VA903m-1
ViewSonic Corporation
58
VA903b-1_ VA903m-1
Item 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121
ViewSonic P/N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A B-00006502 N/A N/A N/A N/A C-00008088 N/A PL-00006589 C-00008089 N/A N/A N/A N/A N/A HW-00008013 N/A N/A N/A N/A
Ref. P/N L004100201101 L013121302A11 Q441240047151 R070000J10311 R070000J20111 R070331J10111 R070470J10111 R070750J10111 R071000J10111 R071001J20111 R071002J20111 R071003J10111 R071004J30111 R071502F30111 R072001J30111 R072200J20111 R073002J10111 R074701J20111 R076801J10111 R144701J20112 T00T390402G01 T00T390602G01 T01A340102A21 Y640307001*1 Y64115HB06*1 XLM191A050001 BLM191AB10113 D462102211201 J4509100102H1 P764P295LM010 XLM191A100003 P727A997LM040-C P763P398LM020-B XLM191A110001 M105223004401 M410810130001 M627700LM0270-E P728A997LM030-A V300800000001 XLM191A200001 M155234008401 M155234010401 M701900LM0190-K P711A997LM010-A
Description Location BEAD Chip Beads DDY160808U011MB 10 200mA 0603(1608) TAPING MAGIC LEAD FREE (SMD) CHIP BEAD Ferrite ChipBeads (high current) WB201209B601QLT02 120 3000mA 1206 Walsin (SMD) CRYSTAL QUARTZ/ 24MHZ 30PPM 20PF 49US CRE (DIP) RES CHIP 0 5%(J) 1/10W 0805 TAPPING (SMD)(Y180320000J0) 05: RESISTOR.RES CHIP 0 5%(J).1/8W 0603 TAPPING (SMD)...... RES CHIP 330 5%(J) 1/10 0603 TAPPING (SMD) RESISTOR.RES CHIP 475%(J) 1/10W.0603 TAPPING (SMD) RESISTOR.RES CHIP 75 5%(J) 1/10W.0603 TAPPING (SMD)...... RES CHIP 100 5%(J) 1/10 0603 TAPPING (SMD) 05: RESISTOR.RES CHIP 1K 5%(J) 1/8W.0603 TAPPING (SMD)...... 05: RESISTOR.RES CHIP 10K 5%(J) 1/8W.0603 TAPPING(SMD)...... RES CHIP 100K 5%(J) 1/1 0603 TAPPING (SMD) RES CHIP 1M 5%(J) 1/16W 0603 TAPPING (SMD) RES CHIP 15K 1%(F) 1/16 0603 TAPPING (SMD) RES CHIP 2K 5%(J) 1/16W 0603 TAPPING SMD)(Y180222001J0) 05: RESISTOR.RES CHIP 220 5%(J) 1/8W.0603 TAPPING(SMD)...... 05: RESISTOR.RES CHIP 30K5%(J) 1/10W.0603 TAPPING (SMD)...... RESISTOR.RES CHIP 4.7K 5%(J) 1/8W.0603 TAPPING(SMD)...... RES CHIP 6.8K 5%(J)1/10W 0603 TAPING (SMD) RES ARRAY 4.7K 5%(J) 1/10W 8P4R 3216 TAPPING (SMD) TR GMBT3904 SOT-23 GTM (SMD) TR GMBT3906 SOT-23 GTM (SMD) XSTR AO3401/ST3401, SOT- 23;3 , Alpha & Omega/ST JACK PHONE EAR (TJ312-5BP- 1) CONNECTOR 180 2mm 6PIN KEY BOARD ASSY LM/MR19I-AAA BARE PCB LM/MR19I-AAA BUTTON BOARD 1SIDE FR-1 T1.6mm REV:1.3 LED,3.0x5.3 mmP=2.54 YELLOW/GREEN (DIP) FFC CONNECTOR P=1mm 10PIN 90 CF16061D0T0 HANQUAN (DIP) SWITCH PA66 BLACK LCDMONITOR SERIES REV:0 BEZEL ASSY(midnight gray)LM/MR19I-AA BEZEL+BUTTON BEZEL ABS HB GRAY PRINT LM/MR19I-AA REV:0 FUNCTION BUTTON PC SILVER PAINT LM/MR17I-AAA REV:0(GAOCHENG ) HOUSING ASSY(midnight gray) LM/MR19I-AA RGB ONLY MACHINE SCREW Bouding 3.0*L6mm NICKEL SCREW 4.0*L8mm NICKEL WITH WASHER Holder SECC LM/MR19I- AA L114*W67.75*H8.1*T1.5mm REV:0 HOUSING ABS HB GREY INJECION LM/MR19I-AA RGB ONLY REV:0 GLUE 50g/BOTTLE (-60~+200) BRACKET ASSY(midnight gray)LM/MR19I-AA bracket+hinge+screw(GAOCHENG ) SCREW plastics,be attacked Low carbon steel /PW4.0*L8mm NICKEL SCREWplastics,be attacked Low carbon steel /PW4.0*L10mm NICKEL SCREW 4.0*L8mm NICKEL WITH WASHER Bracket ABS HB GRAY INJECION LM/MR17I-AA REV:0
Universal number#
Q'ty 3 5 2 2 6 2 3 3 10 5 3 1 1 1 3 8 1 9 2 6 3 4 1 1 1 1 1 1 1 5 1 1 1 1 2 4 1 1 0.01 1 1 2 1 1
ViewSonic Corporation
59
VA903b-1_ VA903m-1
ViewSonic Corporation
60
VA903b-1_ VA903m-1
ViewSonic Corporation
61
VA903b-1_ VA903m-1
Ref. P/N E015-006-W E015-016-1-W P727A901LMC60-C P763P398LM020-B XLM191A050001 M105243005401 E34862190H304 M115233008401 M621700LM0390-G XLM191A040002
XLM1700390010 M105244006401 P369579010001 M711200LM0130-A P612012010001 P74AA997LM010-A P705A997LM030-A P711A995LM030-A M108224008401 M701900LM0140-K M155234008401 P440700450001 M105243006401 P728A995LM130-A M627700LM0270-E M410810130001
ViewSonic Corporation
62
VA903b-1_ VA903m-1
ViewSonic Corporation
63
VA903b-1_ VA903m-1
ViewSonic Corporation
64
VA903b-1_ VA903m-1
9. Block Diagram
ViewSonic Corporation
65
VA903b-1_ VA903m-1
DGND C1 + C7 100uF_16V + R127 1K 1 2 3 4 5 6 CN1 2.0_11pin BKLT-VBRI BKLT-EN 100uF_16V 5V L1 FEB/1206 C2 100nF 5DVCC 3.3V 5V R2 NC/0 R2 NC/0
J1
40mil
R5 100k
Q1 AO3401 3
PANEL POWER
40mil
C4 100nF
FB1
FEB/1206 PANEL_VCC
R3 0/NC R4 10K
5V
+ C6 100uF_16V
C3 22uF/16V
C5 0.01uF
3 ONPANEL_5V 3.3V 5DVCC 3 U3 VIN GND VOUT 2 1117-33/AIC1084-33 C8 100nF DGND JP1 10 9 8 7 6 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1 C132 C131 C130 C129 R123 R116 R117 R118 R119 R120 R121 R122 C128 C127 220 220 220 220 220 220 220 220 LED-2 LED-1 MUTE UP DOWN EXIT MENU POWER L2 FEB/1206 3.3DVCC R6 1K 1 C9 NC 2 Q2 KST3904 DGND
DGND
5DVCC
R7 4.7K BKLT-VBRI R8 2K
R9 NC
HEADER 13/SM
C10 1uF
Q3 KST3904 2 DGND
R126 1K
VBRI
MCU_VCC
R10 330 2 Q4 5DVCC 2N3906 LED-2 R12 4.7K BKLT-EN R14 220 R15 NC LED-1 C70 47uF_16V/NC + C11 R16 10K/NC 100nF 3 3
R11 330
R13
1K
LED2
Q5 2N3906 1 R17
1K
LED1
Q6 KST3904 2 DGND
INVON
ViewSonic Corporation
Model Title Date Rev:
ViewSonic Corporation
66
VA903b-1_ VA903m-1
JP4 6 5 4 3 2 1
JP3 1 2 3 4 5 6 1 2 3 4 5 6 MENU EXIT DOWN UP MUTE DGND 1 3 1 3 1 3 1 3 2 SW1 4 2 SW2 4 2 SW3 4 2 SW4 4 2 SW5 4
HEADER 13/SM
HEADER 13/SM
A1 LED1
A2
HEADER 13/SM
1 3 C
2 4
SW6
1 3
ViewSonic Corporation
Model Title Date
OSD
Rev:
ViewSonic Corporation
67
VA903b-1_ VA903m-1
FBA2 3 5DVCC
FEB/1206
5VA
FBA1 BED/6
CA1 0.1uF
CA2
DGND
0.1uF
AGND AGND
5VA
CA13 0.1uF
CA11 100uF_16V
AGND FBA7 3 STBY 1 3 VOLUME RA3 15K CA3 10uF_16V CNA1 1 2 4 5 3 PHONEJACK 5P UA1 ROUT+ SHUTDOWN RINGND GND VOLUME LOUT+ LINVDD ROUTSE/BTL GND GND BYPASS LOUTVDD 16 15 14 13 12 11 10 9 FBA9 BED/6 CA16 NC/0.1uF RA9 NC/1R2 AGND AGND AGND AGND FBA10 BED/6
CA12 2.2uF_16V
CNA2
E
+
2 3 4 5 6 7 8
FBA6 BED/6
FBA5
BED/6
CA6 NC/180PF
RA5
CA10 47K NC/180PF
RA7 47K
AGND
ViewSonic Corporation
Model Title Date Rev:
ViewSonic Corporation
68
VA903b-1_ VA903m-1
MCU_VCC
VGA5V_1 DVI_POWER
R137 4.7K 8 5 6 4
3.3DVCC R141 0
7 3 2 1
3.3DVCC
C121 100nF
R142 4.7K 22
DGND
C124 100nF
5 6 7 8
RESET_MCU
MCU_VCC
100uF
RP1
5 6 7 8 RP2 4 3 2 1 472_4 472_4 ONPANEL_5V INVON SDIO0 SDIO1 SDIO2 RTD_SD3/SDI RTD_SCSB RTD_SCLK
5 6 7 8
5 6 7 8
RP4
RP3 MCU_RESET
4 3 2 1
472_4
4 3 2 1
472_4 41 40 39 38 37 36 35 34 33 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 NC VSYNC 29 28 27 26 25 24 23 22 21 20 5 6 7 8 P6.7 P6.6/CLK0 P6.5 P6.4 P6.3/AD3 P6.2/AD2 P6.1/AD1 P6.0/AD0
U5 UP DOWN EXIT MENU POWER VOLUME DDC2_SCL DDC2_SDA LED1 IICSDA IICSCL LED2 DDC1_SDA DDC1_SCL R148 100 R149 100 44 45 46 47 48 1 2 3 9 10 11 12 13 14 8 5
P5.0/DA0 P5.1/DA1 P5.2/DA2 P5.3/DA3 P5.4/DA4 P5.5/DA5 HSCL2/P5.6 HSDA2/P5.7 P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P7.6/CLKO P7.7
VCC
RST
MTV512MG
4 3 2 1
XTAL2
XTAL1
VSS
NC
15
16
17
32
NC
RP5
5 6 7 8
RP6
24MHz R152
4 3 2 1
472_4
C125 10pF
ViewSonic Corporation
Model Title Date Rev:
MCU_VCC
Closed to MCU
5DVCC
ViewSonic Corporation
69
VA903b-1_ VA903m-1
L5
FEB/ 0R-0603
R18 R19
AHS0 AVS0 R22 R24 75 0 C15 5pF R25 100 C16 C17 C19 C20 C21 47nF 470nF 47nF G0+ 47nF 47nF G0R0+ G0+ G0R0+ RG1 1M B0B0SOG0 R23 47 C12 47nF B0+ B0+
R20 2K
R21 2K
D2 BAV99 GIN
1 D3 BAV99 BIN
U1 DDC1_SCL DDCSCL 15 VSIN 14 HSIN 13 DDC1_SDA DDCSDA 12 DGND 11 D4 UDZ5.6B D5 UDZ5.6B 5 10 4 9 3 8 2 7 1 6 DGND DGND CONNECT DGND VGA5V VGA5V_1 VGA_B+ BIN VGA_BL6 FEB_0603 VGA_G+ GIN VGA_GL7 FEB_0603 VGA_R+ RIN VGA_RL8 FEB_0603 R28
R26 75
0 C18 5pF
Closed to connector
Closed to connector
Closed to connector
R31 R33 75
0 C22 5pF
R32 47
R34 100
C23
47nF
R0-
R0-
Closed to connector
DDC1_SCL D8
UDZ5.6B JP2
UDZ5.6B
SHELL1 R G B HSYNC VSYNC RGB GND SYNC GND DDC SCL DDC SDA DVI+5V HPD 1/3shield 2/4shield 0/5shield clk shield DAT0+ DAT0DAT1+ DAT1DAT2+ DAT2DAT3+ DAT3DAT4+ DAT4DAT5+ DAT5clk+ clkSHELL2 JACK
DVI_POWER R39 100 DDC2_SDA 10K 1/16W R40 C25 100nF R128 R129 R130 R131 R132 R133 10 10 10 10 10 10 RX0P RX0N RX1P RX1N RX2P RX2N RX0P RX0N RX1P RX1N RX2P RX2N D15 LL5232B 5.6V 5% D16 LL5232B 5.6V 5% DVII_DETECT DDC2_SCL DDC2_SCL DDC2_SDA
R134 R135
10 10
C111 NC/10pF 3 3 3 3 3 3 3 MLL5232B 5.6V D18 BAV99 D19 BAV99 D20 BAV99 D21 BAV99 D22 BAV99 D23 BAV99 D24 BAV99 3 D17 D25 BAV99
C114 2 1 2 100nF
C113 1 2 100nF
C115 1 2 100nF
C117 100nF
C118 100nF
C119 100nF
C116 100nF
C120 100nF
ViewSonic Corporation
3.3DVCC DGND
ViewSonic Corporation
70
VA903b-1_ VA903m-1
PANEL_VCC
R3.3DVCC L9 C27 22pF Closed to Scaler XO R47 6.8KNC 2 C28 22pF Y1 24MHz XI C29 100nF C30 100nF C31 100nF C32 +
FEB/1206
3.3DVCC
3.3DVCC C33 100nF DGND RXE3+ RXE3RXEC+ RXECRXE2+ RXE2RXE1+ RXE1RXE0+ RXE0RXO3+ RXO3RXOC+ RXOCRXO2+ RXO2RXO1+ RXO1RXO0+ RXO0-
22uF_16V
RV1 0
R1.8DVCC L10 FEB/1206 1.8CC C37 R3.3DVCC 100nF C36 + 10uF_16V C38 100nF C39 100nF 3 C40 100nF C41 46 117 47 116 59 72 83 95 108 100nF 60 71 84 96 107 U2 XO XI 127 128 125 126 1 2 3 4 R55 15K 33VRST_REF R3.3DVCC RST_OUT C34 100nF C35 100nF 3.3DVCC DDC1_SDA DDC1_SCL PWM0 RESET_MCU
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
RXO0+
R56 30K 124 33VRST_REF 123 RST_OUT 122 121 120 119 118 115 114 113 112 111 110 109 106 105 104 103 102 101 100 99 98 97 94 93 92 91 90 89 88 87 86 85 82 81 80 79 78 77 76 75 74 73 RXO0RXO0+ RXO1RXO1+ RXO2RXO2+ RXOCRXOC+ RXO3RXO3+ RXE0RXE0+ RXE1RXE1+ RXE2RXE2+ RXECRXEC+ RXE3RXE3+ R60 0 RESET_MCU
R58 4.7K
R59 NC
PLL_VDD
SDIO[3]/PWM2/DDCSDA
33VRST_REF
RESET_OUT
SCLK/PWM0
R61 NC
R62 4.7K
R3.3DVCC 5 6 7 8 9 10 11 12 13 14 15 16 17 18 TMDS_TST / PWM0 / TCON2 REXT TMDS_VDD RX2P RX2N TMDS_GND RX1P RX1N TMDS_VDD RX0P RX0N TMDS_GND RXCP RXCN
XO XI PWM0 R112 4.7K DGND VBRI 3.3DVCC AVS0 AHS0 B0B0+ G0G0+ SOG0 R0R0+
SCSB/PWM1/DDCSCL
XO XI DPLL_VDD DPLL_GND APLL_GND APLL_VDD PLL_TEST1 / TCON0 / TCON3 PLL_TEST2 / TCON1 / TCON12
R63 4.7K R64 R65 1K RX2P RX2N RX1P RX1N RX0P RX0N RXCP RXCN
33VRST_REF RESET_OUT TCON9 / PWM0 DDCSCL2 / VCLK / TCON4 DDCSDA2 / V7 / TCON6 SCLK / V6 / TCON3 SCSB / V5 / TCON7 SDIO[3] / V4 / TCON9 SDIO[2] / V3 / TCON5 SDIO[1] / V2 / TCON8 SDIO[0] / V1 / TCON10 V0 / TCON2/PWM1 TCON13 / COUT 33VPNLOUT AR1N AR1P AR2N AR2P AR3N AR3P AG1N AG1P AG2N AG2P AG3N / TXO0AG3P / TXO0+ ACLKN / TXO1ACLKP / TXO1+ AB1N / TXO2AB1P / TXO2+ AB2N / TXOCAB2P / TXOC+ AB3N / TXO3AB3P / TXO3+ BR1N / TXE0BR1P / TXE0+ BR2N / TXE1BR2P / TXE1+ BR3N / TXE2BR3P / TXE2+ BG1N / TXECBG1P / TXEC+ BG2N / TXE3BG2P / TXE3+
48
47
46
45
44
43
42
41
40
39
38
U6
TXO0+
TXO1+
PGND
TXO0-
TXO1-
VCCK
37
RXO1+
RXO0-
RXO1-
DGND
GNDK GNDK
VCCK VCCK
1.8CC
CN2
CF1601S 30Pin-1.0H(Cvilux)(DIP)
1 2 3 4 5 6 7 8 9 10 11 12
XO XI
36 35 34 33 32 31 30 29 28 27 26 25
R3.3DVCC
NC
RTD2023L
TXO3+ TXE0TXE0+
100nF
100nF 19 20 21 22 23 24 25 26 27 28 29 2 2 2 2 2 2 2 2 2 B0B0+ G0G0+ SOG0 R0R0+ AHS0 AVS0 B0B0+ G0G0+ SOG0 R0R0+ AHS0 AVS0 30 31 32 33 34 35 36 37 38 39 40 AVS0 AHS0 ADC_VDD ADC_GND B0+ B0SOG0 G0+ G0R0+ R0B1- / V7 B1+ / V6 G1- / V5 G1+ / V4 SOG1 / V3 R1- / V2 R1+ / V1 ADC_GND ADC_VDD AHS1 / V0 AVS1 / VCLK
PWM2/DDCSDA/SCLK
PWM1/DDCSCL/SCSB
C42
C43
G+/V4
RTD2523B( LVDS )
13
14
15
16
17
18
19
20
C45 100uF_16V
+C44
C46
C47
R1.8DVCC
10uF_16V
100nF 100nF
BJT_B
DGND
BJT_B 3 3 R68 0 R3.3DVCC 1 Q8 2 2N3906 R1.8DVCC 3 Q9 2 2N3906 1 C48 + R69 NC/1K 3 RTD_SD3/SDI RTD_SCSB RTD_SCLK
50 51
52 53 54 55 56 57
48 49 58 61 62 63 64 65 66 67 68 69 70
PWM1 / TCON0 / COUT PWM2 / TCON1/TCON7 BJT_B BB3P/BBLU7 BB3N/BBLU6 BB2P/BBLU5 BB2N/BBLU4 BB1P/BBLU3 BB1N/BBLU2 BCLKP/BGRN7 BCLKN/BGRN6 BG3P/BGRN5 BG3N/BGRN4
SDIO[0] / TCON13 SDIO[1] / TCON7 SDIO[2] / TCON11 SDIO[3] / TCON0 SCSB / TCON12 SCLK / TCON3
R70
DDC1_SCL DDC1_SDA
R66 R67
100 100
C49
100nF 100uF_16V
ViewSonic Corporation
Model Title Date
1.8CC
SCALER
Rev:
ViewSonic Corporation
71
VA903b-1_ VA903m-1
RXE3-
DGND
22
R1.8DVCC
TXE3-
VCCK
NC/FEB/1206 L11
ViewSonic Corporation
Model Title Date
TOP
Rev:
ViewSonic Corporation
72
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
BOTTOM
Rev:
ViewSonic Corporation
73
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
DRILL DRAWING
Rev:
ViewSonic Corporation
74
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
MASK-TOP
Rev:
ViewSonic Corporation
75
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
MASK-BOTTOM
Rev:
ViewSonic Corporation
76
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
SMD-TOP
Rev:
ViewSonic Corporation
77
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
SILKSCREEN-BOTTOM
Rev:
ViewSonic Corporation
78
VA903b-1_ VA903m-1
ViewSonic Corporation
Model Title Date
SILKSCREEN-TOP
Rev:
ViewSonic Corporation
79
VA903b-1_ VA903m-1
* Readers Response*
Dear Readers: Thank you in advance for your feedback on our Service Manual, which allows continuous improvement of our products. We would appreciate your completion of the Assessment Matrix below, for return to ViewSonic Corporation. Assessment A. What do you think about the content of this Service Manual?
Unit 1. Precautions and Safety Notices 2. Specification 3. Front Panel Function Control Description 4. Circuit Description 5. Adjustment Procedure 6. Troubleshooting Flow Chart 7. Recommended Spare Parts List 8. Exploded Diagram and Exploded Parts List 9. Block Diagrams 10. Schematic Diagrams 11.PCB Layout Diagrams Excellent Good Fair Bad
C. Do you have any other opinions or suggestions regarding this service manual? Readers basic dada: Name: Company: Add: Tel: E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com)
Title:
Fax:
ViewSonic Corporation
80
VA903b-1_ VA903m-1