Professional Documents
Culture Documents
RMS (ACU)
TABLE OF CONTENTS
1
INTRODUCTION ..................................................................................................................................................................................... 3
Page: 2 of 24
INTRODUCTION
Series A
Lapto
Series mini-B
ACU
Battery Management.
Page: 3 of 24
2.1
System Requirements
The following minimum configuration is required to run RMS Software.
2.2
Install ARMS
Follow the configuration below to install the software.
2.2.1
Page: 4 of 24
2.2.2
Connection
Use USB cable (Series A plug to Series mini B plug type) to connected PC
with ACU.
2.2.3
Install Driver
Click Next
Page: 5 of 24
Click Browse
Page: 6 of 24
Start installation
Page: 7 of 24
Success, the HW
installation completed
Click Finish
2.3
Uninstall
Choose ARMS.
Page: 8 of 24
3.1
SYSTEM Components
In addition to PC whose operation system is Windows, the following
components are required:
ACU
3.1.1
RMS Toolbar
This is a listing of RMS menus and Toolbar. You can achieve your desired
function either by clicking toolbar.
3.1.1.1 Toolbar
Below, Figure1, is the toolbar RMS provides.
Figure 1.
Rectifier
Page: 9 of 24
Battery
Alarm
Configuration
Page: 10 of 24
4.1
4.1.1
Page: 11 of 24
4.1.2
4.1.3
Page: 12 of 24
5.1
Function include:
Current limit setting
High voltage shut down setting
SMR individual alarm event list
Page: 13 of 24
5.2
Battery Information
5.2.1
Function include:
Summary
Parameter setting
Battery test
Temperature compensation
Boost charge
Page: 14 of 24
5.2.2
Summary
Function:
Display all of the Battery setting values information.
5.2.3
Parameters
Function include:
Floating Voltage setting
Equalizing Voltage setting
RMS (ACU) User Manual
Page: 15 of 24
Battery Capacity
Max. Charge I setting
5.2.4
Battery Test
Function include:
Battery failure Voltage setting
Battery test discharge current setting
Battery test capacity setting
Periodic test cycle setting
Periodic test count down timer:
The timer will be count down automatically when the Periodic test function
enable.
Page: 16 of 24
Timer start
counting down
Battery test
started
The timer will be count down automatically when the battery test function
starting.
5.2.5
Temperature compensation
Function include:
Temperature compensation enable/disable
Temperature coefficient setting
Reference Temperature setting
Compensation Voltage display (automatic calculating)
Page: 17 of 24
5.2.6
Boost charge
Function include:
Boost charge Voltage Mode enable/disable
Boost charge Capacity Mode enable/disable
Boost charge Recharge Mode enable/disable
Boost charge Periodic Mode enable/disable
Boost charge stop criterion setting:
1. Min. Charge current setting
2. Charge duration time setting
Periodic boost charge count down timer:
The timer will be count down automatically when the Periodic Mode function
enable.
Page: 18 of 24
The Estimation Cap show in the ARMS is indicate the immediately battery
remaining capacity. The ACU is able to count the battery capacity automatically
through battery charge/discharge * t to counting the battery immediately
capacity.
5.3
Function include:
DCV Alarm threshold setting
Battery temperature Alarm threshold setting
Major/Minor Alarm definition
Relay 1~6 definition
Page: 19 of 24
5.4
Configuration Setting
Function include:
SMR type select
Shelf/SMR setting (Digital type only)
Low voltage disconnect setting
Temperature unit setting
ACV detection board (optional)
Hall sensor type select
Page: 20 of 24
5.5
Others
5.5.1
System Information
System information is display on the top left side of the screen for monitoring
the status of the system.
5.5.2
5.5.3
5.5.4
Alarm/Event List
Alarm/Event list area is located on the left side of the screen (beneath the
battery test button). It can list current Alarms/Events.
Technician can through the RMS (user software) to clear the current
Alarm/Event. But the controller will issue the Alarm/Event if the system still had
failure condition after through the RMS to clear them.
5.5.5
Connection Port
The connection port area is located on the left bottom side of the screen. It can
select to PC connecting port from COM0 to COM99.
5.5.6
Page: 21 of 24
Key in 54.0
Press Enter
Page: 22 of 24
P.S: Any parameter settings modified must press Enter after key in the new
value, to save the new settings to controller
Page: 23 of 24
RMS (ACU)