Professional Documents
Culture Documents
0 1 0 8 2 0 0 7
www.anykits.com sales@anykits.com
1 4
MICROCONTROLLER/INTERFACE
14
16
LIGHT EFFECTS
18
POWER SUPPLY
20
REMOTE CONTROL
25
BUILDING BLOCKS
26
MINI KITS
28
MISCELLANEOUS
30
MOTOR/MOTION CONTROL
32
AUDIO/HI-FI
STEREO TAPE HEAD PREAMPLIFIER
Power supply - 9 ~ 12 VDC @ 20 mA Output power - upto 200 mW Input Resistance - 100 K (Typ), Load
A002
A003
The Stereo Tape Head Preamplifier kit is based on LA3161 IC from SANYO.
TDA2006 12W Audio Amplifier Kit is a Low Frequency Class AB amplifier. Power supply - upto 18 VDC Output power - 12 W @ 4 , 8 W @ 8 TDA2006 provides high output current Has very low harmonic and cross-over distortion Short circuit protection / Thermal shutdown system in IC Terminal pins for connecting left and right audio signal inputs Relimate Connector for connecting Potentiometer (POT) for volume adjustment Power Battery Terminal (PBT) for easy power supply and speaker connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 51 mm x 63 mm
Resistance - 10 K (Typ)
Low noise, good ripple rejection owing to
A004
5.5W + 5.5W Audio Amplifier Kit is based on LA4445 IC form SANYO. It can be used as a car radio amplifier, tape recorder etc.
Power supply - 12 - 16 VDC Output power - 5.5 W + 5.5 W @ 4 Ohm Good ripple rejection, good channel
A005
separation, small residual noise Thermal, overvoltage, short protector inbuilt into IC Terminal pins for connecting left and right audio signal inputs Relimate Connector for connecting Potentiometer (POT) for volume adjustment Power Battery Terminal (PBT) for easy power supply and speakers connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 44 mm x 74 mm
The Tiny Audio Amplifier kit is a good choice for battery operation. It is based on LM386 IC.
Power supply - 6 - 12 VDC Output power - 1 W, 8 Ohm The quiescent power drain is only 24 mW
power supply
LM4730 Stereo 14W Audio Amplifier kit can be used for High-end Stereo TVs, Compact Stereo etc.
A008
Dual power supply - 18 VDC Output power - 14 W + 14 W, 8 Ohm Less then 10% THD+N from 20 Hz - 20 KHz Onboard slide switch for mute and standby mode Terminal pins for connecting left and right audio signal inputs Relimate connector for connecting Potentiometer (POT) for volume adjustment Power Battery Terminal (PBT) for easy dual power supply and speakers connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 82 mm x 88 mm
Power supply - 5 - 12 VDC @ 10 mA Output - Gain 100 On-Board Condenser MIC Terminal pins for connecting of power supply and output Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 40 mm x 39 mm
A011
1.6W Mono Audio Amplifier kit is based on TDA7231, which is class AB power amplifier with a wide range of supply.
Power supply - 5 ~ 12 VDC Output - 1 W, 4 Low crossover distortion, soft clipping Onboard PRESET to adjust volume Terminal pins for connecting power supply, input and output ON/OFF PCB mounted slide switch for power supply Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 36 mm x 52 mm
sales@anykits.com
www.anykits.com
AUDIO/HI-FI
STEREO 10W AUDIO AMPLIFIER A009 20W BRIDGE AUDIO AMPLIFIER A010
Stereo 10W Audio Amplifier kit is a Hi-fi Stereo Amplifier, it is based on TDA1521 IC.
Power supply - 18 VDC Output power - 2 X 10 W (THD 0.5%), 8 Excellent gain balance between channels.
20W Bridge Audio Amplifier kit, based on the TDA2005 IC, a class B dual audio amplifier, specifically designed for car radio applications etc.
Power supply - 18 VDC Output power - 20 W, 4 IC built in Thermal Shut-down, Load dump
Gain 30 dB
IC is short circuit and thermally protected Terminal pins for connecting left and right
audio signal inputs Power Battery Terminal (PBT) for easy power supply and speakers connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 39 mm x 65 mm
A012
The Mono Audio Preamplifier kit has been developed to amplify the low level audio signals. It is based on commonly available Op-Amp. It can be used as a Mic preamplifier etc.
output Terminal pins for connecting power supply Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 47 mm x 58 mm
Power supply - 12 ~ 24 VDC @ 20 mA Output - Gain 35 adjustable Onboard PRESET to adjust Gain, Level Terminal pins for connecting power supply, input and output Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 42 mm
Mini Stereo Audio Amplifier kit is designed for portable radio players and other building block projects. It is based on TDA2822 IC.
Power supply - upto 12 VDC Output - 1 W, 8 for 12 VDC / 20 mW,
32 for 3 VDC
Input resistance - 100 K Low crossover distortion, Low quiescent
current Onboard PCB mount 3.5 mm stereo jack for audio-in Onboard Presets to adjust volume Terminal pins for connecting power supply and outputs Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 41 mm x 56 mm
2
IC built in short circuit, thermal shut-down,
A016
TINY MIC PREAMPLIFIER A017
1.6W Audio Amplifier kit can used as a low frequency class B power amplifier with wide range of supply voltage.
Power supply - 3 - 12 VDC Output - 1.6 W, 4 / 1.2 W, 8 Input resistance - 5 M Low quiescent current, good ripple rejection and no cross-over distortion Onboard presets to adjust volume Terminal pins for connecting power supply, input and output Four mounting holes of 3.2 mm each PCB Dimensions 44mm x 47mm
The Tiny Mic Preamplifier kit is based on a single transistor amplifier design. It amplifies the output of the condenser Mic. Good choice for Karaoke.
Power supply - 5 - 9 V DC @ 2 mA PCB dimensions 26 mm x 56 mm
sales@anykits.com
www.anykits.com
AUDIO/HI-FI
AUDIO SIGNAL TO LIGHT UNIT A019
Audio Signal to Light Unit kit is an audio to light modulator, which controls the intensity of light in response to an audio input. This kit is ideal for dance parties, DJ, Discotheques etc.
5 LED VU METER
A018
5 LED VU Meter kit is based on LB1403 IC from SANYO, which will indicates the volume level of the audio signal it senses.
Power supply - 6 ~ 12 VDC @ 90 mA Lighting levels remain stable to line
Input - Audio signal AC Power supply - 230 VAC Load - 230 W Input isolated with the use of Opto-coupler Onboard Presets to adjust level Terminal pins for connecting audio input Four mounting holes of 3.2 mm each PCB dimensions 36 mm x 50 mm
regulation because of on-chip voltage reference LED's are driven by a constant current Onboard presets to adjust input sensitivity Terminal pins for connecting power supply, audio input Four mounting holes of 3.2 mm each PCB dimensions 34 mm x 52 mm
A021
A020
12W Hi-Fi Audio Amplifier kit built around TDA2030 IC, intended to be used as a low frequency class AB amplifier.
Power supply - 24 VDC Output - 12 W, 4 Input resistance - 5 M Very low harmonic distortion (0.5%) and cross-over distortion IC built in Short circuit, Thermal shut-down Terminal pins for connecting audio input Power Battery Terminal (PBT) for easy power supply and speaker connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 39 mm x 60 mm
Power supply - 14 VDC Output - 6 W, 4 Input resistance - 150 K Very low harmonic and cross-over distortion IC built in short circuit, thermal overrange, load dump voltage surge protected Onboard PRESET to adjust volume Terminal pins for connecting audio input Power Battery Terminal (PBT) for easy power supply and speaker connection Power-On LED indicator Heatsink provided for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 33 mm x 71 mm
6W + 6W Stereo Audio Amplifier kit is based on LA4440 IC from SANYO. Power supply - 12 VDC Output - 2 X 6 W, 4 Input resistance - 30 K Low distortion (THD - 0.1%), Good channel separation and ripple rejection IC built-in thermal, overvoltage, pin-to-pin short protector Terminal pins for connecting inputs Power Battery Terminal (PBT) for easy power supply and speakers connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 41 mm x 72 mm
Power supply - 12 VDC Output - 5 W + 5W, 3 Input resistance - 100 K Good distortion (THD - 0.3%), Good channel balance Berg pins for connecting of inputs Power Battery Terminal (PBT) for easy power supply and speakers connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 45 mm x 73 mm
A024
channel separation and ripple rejection IC built-in thermal, short circuit protections Internal output protection diodes Terminal pins for connecting input Power Battery Terminal (PBT) for easy power supply and speaker connection Power-On LED indicator Heatsink for IC Four mounting holes of 3.2 mm each with nut and stud PCB dimensions 48 mm x 60 mm
sales@anykits.com
www.anykits.com
ALARM/SOUND EFFECTS
20 SEC VOICE RECORD / PLAYBACK B001 120 SEC VOICE RECORD / PLAYBACK B002
20 Sec Voice Record / Playback kit will playback and record upto 20 seconds of voice message. This kit is an excellent choice to add voice to your project. This kit is built around ISD1420 IC.
Input supply - 5 VDC @ 120 mA Output - Speaker, 16 Upto 20 Seconds of non volatile voice
120 Sec Voice Record / Playback kit will playback and record upto 120 seconds of voice message. This kit is built around ISD25120 IC.
Input supply - 5 VDC @ 120 mA Output - speaker, 16 Upto 120 Seconds of non volatile voice
storage
Slide switch for easy selection of Playback
storage Power-On LED indicator Onboard MIC capsule for recording message directly onto the chip Flashing LED to display Record / Playback of messages Direct speaker connection via Relimate Connector Relimate type connector for Power Supply Input 4 pin small tactile switches for Record and Play function trigger Four mounting holes of 3.2 mm each PCB dimensions 59 mm x 67 mm
/ Record mode
Onboard MIC capsule for recording
of messages
ON Board ON/OFF Switch Power-On LED indicator Direct speaker connection via Relimate
Connector
Relimate type connector for power supply
input
4 pin small tactile switches for Start /
B003
Water Level Buzzer is a simple kit which will buzz when water reaches the sensor level.
B004
Input - 9 VDC @ 40 mA Output - Buzzer Terminal pins for supply voltage Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 32 mm x 35 mm
Light Sensitive Audio Oscillator kit is a fun loving kit which will create different sound effects depending on the light falling on the sensor (LDR).
Input - 5 ~ 12 VDC Output - Speaker Terminal pins for supply voltage and
speaker connection
Power-On LED indicator PCB dimensions 38 mm x 44 mm
3 Tone Musical Bell is a kit built around BT66T IC driving LM386 audio amplifier to give that extra punch.
Input - 6 VDC @ 200 mA Output - Speaker Terminal pins for supply voltage and
3 Tone Audio Oscillator is a simple circuit which will generate audio tone on the press of a button. This circuit can be very useful as a test equipment for audio equipments or as a signal source for an audio input.
Input - 12 VDC @ 100 mA Output - Speaker, 8 / 0.25 W Three switches produce 1.5 KHz, 1 KHz
speaker connection Power-On LED indicator ON/OFF Switch on the PCB Four mounting holes of 3.2 mm each PCB dimensions 35 mm x 54 mm
and 450 Hz
Terminal pins for supply Voltage and
speaker connection
3 TONE SIREN
B008
Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 42 mm x 48 mm
3 Tone Siren kit produces Gun Sound, Police Siren and Ambulance Siren effects from a speaker. This kit is built around UM3561 IC driving an LM386 audio amplifier to give that extra punch.
Input - 6 VDC @ 200 mA Output - Speaker, 8 / 0.5 W Two slide switches select and play different
B007
tones
ON/OFF slide switch for power supply Terminal pins for supply voltage and
2 Tone Audio Oscillator is a simple circuit which will generate audio tone on the press of a button. This circuit can be very useful as test equipment for audio equipment or as a signal source in an audio input.
Input - 5 ~ 12 VDC @ 100 mA Output - Speaker, 8 / 0.25 W Two switches produce / play different
speaker output Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 42 mm x 64 mm
frequencies Terminal pins for supply voltage Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 47 mm x 46 mm
sales@anykits.com
www.anykits.com
ALARM/SOUND EFFECTS
AUDIO OSCILLATOR B009 VOICE MODULATOR B010
Audio Oscillator kit simply produces audio tones for use in the range of 115 Hz to 1 KHz. This kit is a must for audio technicians and experimenters alike.
Input - 6 VDC @ 325 mA Output - Speaker, 8 / 0.5 W Range 115 Hz to 1 KHz selectable by
Voice Modulator kit is designed around HT8950A to provide two special sound effects viz. Vibrato & Robot.
Input - 6 VDC @ 300 mA Output - Speaker, 8 / 0.5 W 7 Step level shifting (Volume Control) SW3
onboard PRESET ON/OFF slide switch for power supply Terminal pins for supply voltage and speaker output Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 39 mm x 42 mm
(TGU) and SW4 (TGD) SW2 - vibrato mode, SW5 - robot mode LED to display the voice level input ON/OFF slide switch for power supply Audio amplifier type LM386 with volume control preset PBT (Power Battery Terminal) connectors for supply voltage and speaker output Power-On LED indicator PCB dimensions 63 mm x 68 mm
VOICE CHANGER
Voice Changer kit can be used to transpose or distort one's voice by encoding the sound appearing at the Microphone input. This kit is built around AP8072 IC.
Input - 6 VDC @ 200 mA Output - Speaker, 8 / 0.5 W Audio amplifier type LM386 with volume
Telephone Siren COB kit can be used to emulate the Telephone Ringer sound for your project without the need of a telephone line. This kit can be used in toys and science fair projects.
control preset Slide switch selectable tone frequency for encoding sound 4 Tones to choose Built in noise reduction circuit for reducing environment noise ON/OFF slide switch for power supply Terminal pins for supply voltage and speaker output Four mounting holes of 3.2 mm each PCB dimensions 61 mm x 65 mm
Input - 3 VDC (2 AAA Battery) Output - Speaker, 8 / 0.25 W Tactile switch for trigger Four mounting holes of 3.2 mm each PCB dimensions 31 mm x 39 mm
B015
Voice Module 60 Sec kit will playback and record upto 60 seconds of voice message. This kit is an excellent choice to add voice of upto 350 mW to your project.
Upto 60 Seconds of non volatile voice
Voice Module 20 Sec kit will playback and record upto 20 seconds of voice message.
Upto 20 Seconds of non volatile voice
storage
Upto eight segments record and play
storage
Onboard MIC capsule for recording
option available
Easy and clear, jumper selectable mode
option
Reset switch available for use in Tape
external audio source Easy jumper selection for selecting recording source Flashing LED to display Record / Playback of messages Direct speaker connection via Relimate Connector Relimate type connector for power supply input 4 pin small tactile switches for Record and Play function trigger Onboard voltage regulator for a regulated supply Diode protection against reverse polarity connection of power supply Preset for adjusting sampling rate and record level of voice record/play 28-Pin IC socket for the main IC Four mounting holes of 3.2 mm each PCB dimensions 70 mm x 58 mm
mode
Upto 350 mW of audio output available to
drive a speaker
Onboard MIC capsule for recording
recording source
Flashing LED to display Record / Playback
of messages
Direct speaker connection via Relimate
Connector
Relimate type connector for power supply
input
4 pin small tactile switches for Record and
supply
Diode protection against reverse polarity
sales@anykits.com
www.anykits.com
ALARM/SOUND EFFECTS
MULTI TUNE COB B013 APR9600 ADD-ON VOICE MODULE B016
Multi Tune COB will provide different tunes for your project. The output from the COB (Chip On Board) will drive an audio amplifier based on LM386. Can also be used as a Door Bell.
APR9600 Add-On Voice Module kit will playback and record upto 60 seconds of voice message. This kit is an excellent choice to add voice to your project.
Upto 60 Seconds of non volatile voice
Input - 6 VDC @ 200 mA Output - Speaker, 8 / 0.5 W Tactile switch for trigger Power-On LED indicator Terminal pins for supply voltage and speaker output Four mounting holes of 3.2 mm each PCB dimensions 35 mm x 63 mm
storage
Upto eight segments record and play
option available
All trigger inputs and supply available for
easy connection to your controlling interface Jumper selectable mode option Jumper enabled record option Reset switch available for use in Tape mode Onboard MIC capsule for recording message directly onto the chip Flashing LED to display Record / Playback of messages Direct speaker connection via Relimate Connector 5V DC Power Supply required Preset for adjusting sampling rate, record level and Volume Level of voice record/play 28 pin IC socket for the main IC Four mounting holes of 3.2 mm each PCB dimensions 67 mm x 52 mm
sales@anykits.com
www.anykits.com
MICROCONTROLLER/INTERFACE
PIC16F 28-PIN DEVELOPMENT BOARD C001 PIC18F 28-PIN DEVELOPMENT BOARD C002
PIC16F 28-Pin Development Board will help you with your prototyping requirement with any of Microchip's 28pin PIC microcontrollers.
16X2 backlight LCD which mounts on the
PIC18F 28-Pin Development Board will help you with your prototyping requirement with any of Microchip's 18F 28pin PIC microcontrollers.
ICSP connector for programming for the PICs
back side (Track Side) of the PCB ICSP connector for programming for the PIC's with ICD support 2 LED's connected to the two CCP ports for PICs with PWM output With DIP-28 microcontroller socket 4 MHz Crystal Resonator 3 User Buttons PBT for power plug-in Onboard +5V voltage regulator with diode protection for reverse polarity Relimate Connectors for easy connection of port pin of the MCU to external interfacing 4K EEPROM (24C04) to store valuable data for PIC's without Internal EEPROM PBT for supplying 5V regulated supply to external interface Infra Red Receiver Sensor for IR related study or project Four mounting holes 3.2 of mm each PCB dimensions 71 mm x 87 mm
Relimate Connector with +Vcc and Gnd connection Onboard +5V voltage regulator with a diode bridge to provide any polarity connection to the power-in PBT Power-On LED indicator A jumper option given to allow a MCLR/RA3 pin to be used as a general purpose Input Pin Four mounting holes of 3.2 mm each PCB dimensions 80 mm x 71 mm
4 X 4 MATRIX KEYBOARD
C004
C003
4 Digit 7-Segment Display Using 74HC595 kit drives four 7-Segment common cathode display using Serial Shift Register IC.
Four 0.5" common cathode display Input / Output connector for connecting
Matrix style keyboard 4 column X 4 rows Sturdy 4 pin big tactile switch 8 Pin well marked Relimate connector for easy connection Four mounting holes of 3.2 mm each PCB dimensions 79 mm x 72 mm
C007
8 Relay Board for IR/RF Interface kit offers 8 relay output control for your project.
C005
(SPDT) relays
Transistor driven control with LED
6 Digit 7-Segment Multiplexed Display kit offers 6 digit common anode/cathode Multiplex Display.
0.5" 7-segment display (common anode or
indication
Diode protection for Back EMF generated 3-Pin PBT connector for easy connection of
common cathode)
Multiplex style connection of the 7-
Segments of all the display Individual lines for the common pin of each of the segment Series resistor for each of the 7 segment of the display to regulate current Well marked 14-Pin relimate connector on board for easy connection Four mounting holes of 3.2 mm each PCB dimensions 42 mm x 103 mm
ease of connection
Power-On LED indicator Well marked 14-Pin relimate connector on
C008
LCD MODULE
C013
8 Tact Switches Input Board kit offers 8 key inputs for your project. Pull Up resistors to Vcc 8-Pin DIP Switch 8 Tactile key input Well marked 8-Pin relimate connector on board for easy connection Separate 2-Pin Relimate connector for supply line Four mounting holes of 3.2 mm each PCB dimensions 38 mm x 84 mm
LCD Module kit offers an easy way of interfacing a 16X2 Alphanumeric LCD.
Interfacing 16X2 backlight alphanumeric
LED
Preset to adjust the contrast level of the LCD 8-Pin relimate connector for easy connection
sales@anykits.com
www.anykits.com
MICROCONTROLLER/INTERFACE
89C2051 DEVELOPMENT STICK C010 MULTIPURPOSE PIC16F 18-PIN DEVELOPMENT BOARD C015
89C2051 Development Stick kit offers an easy way of interfacing 89C2051 compatible MCU's.
Slim design with plug in type approach Voltage regulator on board for stable and
Multipurpose PIC16F 18-Pin Development Board provide you with your prototyping requirement.
ICSP connector for programming for the
regulated supply to the MCU RESET switch for resetting the MCU 11.0592 MHz Crystal 4K external EEPROM Power-On LED for indicator 20-Pin well marked Berg connector for ease of connection Access to all IO pins & supply pin on the Berg connector 20-Pin IC socket for MCU Four mounting holes of 3.2 mm each PCB dimensions 35 mm x 72 mm
relimate connector with +Vcc and Gnd connection PBT for Power plug-in Onboard +5V Voltage regulator to provide regulated power to the board Diode to provide against wrong polarity connection to the board Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 54 mm x 54 mm
C014
C019
With RS485 Controlled 8 Relay Board you can control upto 8 SPDT (Single Pole Double Throw) relays using a simple RS485 protocol.
RS232 Interface Module is a simple add-on kit to connect your 5V Serial Data Output to the PC.
MAX232 based Level Shifter IC Simple and straight forward design Easy connection via Relimate connector to
Upto 8, 12V SPDT relay control Industry standard relay drive IC - ULN2803 Data received indicator LED LED indicator to display relay state Power-On LED indicator On board regulator IC PBT type connector for easy connection of all wires to the PCB Simple RS485 Protocol Can be controlled either by a microcontroller board or via PC using suitable RS232 - RS485 converter Diode protection against reverse polarity connection NC-C-NO pin outs from each relay into a PBT connector Four mounting holes of 3.2 mm each PCB dimensions 166 mm x 92 mm
C020
RS232 to RS485 Module kit will provide you a seamless connection between a PC and an RS485 network.
Simplex connection of the interface to the
RS485 network
Easy switching mode between Receiver
and Transmitter
RC SIGNAL READER
C016
board
9-Pin, PCB mounted, female type D
connector available
Supply can also be provided by the host
RC Receiver Power-On LED indicator On board regulator IC Clearly marked 8pin relimate connector for connecting the Decoder PCB to the LCD module (C013) Relimate Connector for Power and RC Signal-in Resonator based circuit for error free computation Four mounting holes of 3.2 mm each PCB dimensions 57 mm x 41 mm
interface via Relimate connectors carrying data Four mounting holes of 3.2 mm each PCB dimensions 64 mm x 43 mm
sales@anykits.com
www.anykits.com
MICROCONTROLLER/INTERFACE
SERIAL PIC PROGRAMMER C021 SINGLE DIGIT BIG DISPLAY MODULE USING 74HC595 C022
Serial PIC Programmer kit is a must have for all those who develop, experiment, program and play with Microchip based PIC projects.
JDM compatible interface design ICSP and direct chip level programming
Single Digit Big Display Module Using 74HC595 kit will display large 7segment single digit number, 3.4 inch in height, which can be visible over large distance. More digits can be connected serially to each other easily.
Each segment made up of 5 LEDs Series current limiting resistors provided
available ZIF type socket for easy placement and removal of the microcontroller LED indication of programming being done No power supply needed. May not work on laptops where the voltage may be below 7.3 V Zener Diode protected design 9-Pin PCB mounted female type D connector provided for PC side connection Selector switch for selecting different PIC type during programming in ZIF socket Marker points provided on PCB for proper insertion point of different PIC's in the ZIF socket Four mounting holes of 3.2 mm each PCB dimensions 53 mm x 108 mm
protocol
Separate Relimate type connector for
connecting Input/Output
Separate supply pins for data and LED
input
Four mounting holes of 3.2 mm each PCB dimensions 125 mm x 58 mm
C025
source
Resonator based design for better accuracy Two mounting holes of 3.2 mm each PCB dimensions 30 mm x 37 mm
supply on board
PBT type connector for connecting power
supply to the board Relimate type connector to connect the sensor to the Kit and LCD to Kit Diode protection against reverse polarity connection of power supply Four mounting holes of 3.2 mm each PCB dimensions 48 mm x 43 mm
C027
4 Digit 7-Segment Multiplex Display kit will provide 4 digit of multiplexed display for your project.
5V Supply operation 0.5 - CA type display Switching of power to the display via
switching transistor
Standard Box Header for easy connection
C026
This kit will provide 3.3 V @ 800 mA DC Regulated Supply. The kit based on the LM1117 Low-Dropout Linear Regulator.
Input - 5 to 15 VDC Output - 3.3 V @ 800 mA regulated low
of the board to various development boards or project Four mounting holes 3.2 mm each PCB dimensions 74 mm x 42 mm
ripple DC voltage
Current limiting and Thermal shutdown
C028
This simple A2D (Analog to Digital) Converter Board can log upto 8 channel of analog signal with 8 bit resolution. This board uses the famous ADC0808 chip from National Semiconductor.
Two standard box type header connector
C033
4 Bi-Colour LED board provides a simple visual indication to any application which you may require.
Interfacing via box header type connector Jumper selectable common anode or
for easy connection of the board to various development boards or project Separate box header for Data and Control signal for the ADC PBT type connector for easy connection of Analog signal input or sensor connection to the board +5 VDC and Gnd connection available for sourcing supply for your sensor or add-on interface or signal conditioner board On board oscillator source for the analog to digital converter Four mounting holes 3.2 mm each PCB dimensions 54 mm x 63 mm
sales@anykits.com
www.anykits.com
MICROCONTROLLER/INTERFACE
60 SEC RECORD/PLAYBACK MODULE C029 AT89Sxx DEVELOPMENT BOARD C030
60 Sec Record/Playback Module kit will playback and record upto 60 seconds of voice message. This kit is an excellent choice to add voice to your project.
Upto 60 Seconds of non volatile voice
Our AT89Sxx Development Board provides a very simple and cost effective platform for prototyping solution. The compact design provides connection to all the pins of the microcontroller for the user.
Prototyping solution available for 40-pin
storage Upto eight segments record and play option available Trigger inputs and supply source available to the board via standard box header connector Standard audio amplifier capable of delivering upto 350 mW of audio amplification with Volume adjust preset Jumper selectable mode option Jumper enabled record option Reset switch available for use in Tape mode Onboard MIC capsule for recording message directly onto the chip Flashing LED to display Record / Playback of messages Speaker Connection via PBT Connector 5 VDC Power Supply required Preset for adjusting sampling rate, record level and Volume Level of voice record/play 28-pin IC socket for the main IC Four mounting holes of 3.2 mm each PCB dimensions 50 mm x 88 mm
standard 10 pin box header with supply of 5 VDC for interfacing circuits ISP (In circuit Serial Programming) connector available for chips with ISP support 11.0592 MHz crystal on board Pull-up resistor network for Port 0 of the microcontroller UART level shifter circuit using MAX232 IC, on board for easy connection of the board to the RS232 devices Jumper selectable connection available for connecting the UART level Shifter to the port pins On board voltage regulator available for sourcing regulated 5V @ upto 1A voltage to the board and connecting circuit Power-On LED indicator AUX Power source of 5 VDC available on a PBT connector for sourcing DC supply to interfacing circuits Four mounting holes of 3.2 mm each PCB dimensions 74 mm x 97 mm
C031
C032
Our ATmega8 Development Board provides a very simple and cost effective platform for prototyping solution. The compact design provides connection to all the pins of the microcontroller for the user.
Prototyping solution available for 28-pin
Our ATmega16/32 Development Board provides a very simple and cost effective platform for prototyping solution. The compact design provides connection to all the pins of the microcontroller for the user.
Prototyping solution available for 40-pin
ATmega series AVR microcontroller from ATMEL All the three ports available to the user via standard 10 pin box header with supply of 5 VDC for interfacing circuits Onboard reset switch for easy reset of the microcontroller ISP (In circuit Serial Programming) connector available for chips with ISP support 8 MHz crystal on board UART level shifter circuit using MAX232 IC, on board for easy connection of the board to the RS232 devices Jumper selectable connection available for connecting the UART level Shifter to the port pins On board voltage regulator available for sourcing regulated 5V @ upto 1A voltage to the board and connecting circuit Power-On LED indicator AUX Power source of 5 VDC available on a PBT connector for sourcing DC supply to interfacing circuits Four mounting holes of 3.2 mm each PCB dimensions 60 mm x 89 mm
ATmega series AVR microcontroller from ATMEL All the four ports available to the user via standard 10 pin box header with supply of 5V DC for interfacing circuits Onboard reset switch for easy reset of the microcontroller ISP (In circuit Serial Programming) connector available for chips with ISP support 8 MHz crystal on board UART level shifter circuit using MAX232 IC, on board for easy connection of the board to the RS232 devices Jumper selectable connection available for connecting the UART level Shifter to the port pins On board voltage regulator available for sourcing regulated 5V @ upto 1A voltage to the board and connecting circuit Power-On LED indicator AUX Power source of 5 VDC available on a PBT connector for sourcing DC supply to interfacing circuits Four mounting holes of 3.2 mm PCB dimensions 64 mm x 101 mm
PROTOTYPE BOARD
Prototype Board is a simple PCB offering easy connection of a standard 10-pin Box Header connector to prototyping area. PCB dimensions 96 mm x 56 mm
C034
sales@anykits.com
10
www.anykits.com
MICROCONTROLLER/INTERFACE
8 WAY DIP SWITCH BOARD
8 Way DIP Switch Board is a simple PCB offering easy connection of a standard 10-pin Box Header connector to a 8 way DIP Switch with a jumper selectable pull-up / pull down of resistor network connected in parallel. PCB dimensions 32 mm x 37 mm
C035
C036
C037
C038
RS232 to RS485 Board (R) provides a seamless connection of the PC to an RS485 network.
Simplex connection of this interface to the
RS485 network
Easy way of switching the modes between
connector available
C039
DTMF Development Board offers a very convenient way to generate DTMF tones and demodulate it. It uses the famous MT8880/MT8888 DTMF transreceiver IC from Mitel.
Easy 10 pin Box Header connector for
interface via relimate connector carrying data Four mounting holes 3.2 mm each PCB dimensions 82 mm x 33 mm
C040
accurate generation and demodulation of DTMF tones for your project Onboard upto 350 mW audio amplifier block for DTMF tones with Volume Adjust Preset 5V Supply sourced via interfacing Box Header Relimate/Berg type analog connection Four mounting holes 3.2 mm each PCB dimensions 56 mm x 49 mm
EEPROM Add-On Board offers an easy way to interface a standard 24Cxx type I2C EEPROM to your project.
5 VDC supply sourced through the
C041
C042
Our simple GLCD Adapter Board offers an easy way to interface a standard GLCD to your project.
5 VDC supply sourced through the
I/O Expander Board offers a convenient way to interface upto 16 I/O pins in your project using SPI/I2C bus. This kit uses the famous MCP23x17 IO chip from Microhip.
Supply sourced through the interfacing Box
available for interfacing of data bus and control bus to the interfacing unit Contrast control preset also available PCB dimensions 53 mm x 33 mm
Header connector
The kit has 2 separate Box Header type
connector for the 16 pins of I/O port and 1 Box Header for interfacing of the PCB with the host controlling circuit Jumper selectable address option is also available for this kit Four mounting holes 3.2 mm each PCB dimensions 58 mm x 54 mm
C043
Our simple LCD Adapter Board offers an easy way to interface a standard 16X2 LCD to your project.
Supply sourced through the interfacing Box
Header connector
Interfacing is via standard box header
connector
Contrast control preset also available PCB dimensions 42 mm x 24 mm
sales@anykits.com
11
www.anykits.com
MICROCONTROLLER/INTERFACE
8 LED OUTPUT BOARD - SINK C044 8 LED OUTPUT BOARD - SOURCE C045
This simple 8 LED Output Board - Sink, offers a convenient way to monitor or display output of various I/O pins for your project.
Interfacing is via 10-pin Box Header
This simple 8 LED Output Board - Source, offers a convenient way to monitor or display output of various I/O pins for your project.
Interfacing is via 10-pin Box Header
connector
Four mounting holes 3.2 mm each PCB dimensions 75 mm x 23 mm
4 X 4 MATRIX KEYBOARD
C046
C047
Matrix style keyboard 4 Column X 4 Rows Sturdy 4-pin big Tactile Switch Box Header connector for easy connection Four mounting holes 3.2 mm each PCB dimensions 59 mm x 63 mm
Opto-Isolated I/O Board offers a compact & convenient way to interface industrial type inputs/outputs to your microcontroller boards, Signal transmission between circuits of different potentials and impedances etc.
4 optoisolated inputs & 4 optoisolated
outputs
Std TTL input signals for opto-couplers Interfacing is via 10-pin Box Header and
C048
Power Battery Terminal (PBT) type connector Power source LED indicator Four mounting holes 3.2 mm each PCB dimensions 54 mm x 64 mm
PIC16F 28/40-pin Development Board will help you with your prototyping requirement with any of Microchip's 28/40-pin of 16F PIC microcontrollers.
All ports terminating in separate box
C049
header with 5 VDC source option ICSP connector for programming for the PIC's with ICD support Jumper selectable on board pull up resistor for PortA.4 pin on the microcontroller Bridge in the input provides any polarity DC supply connection to the board 20 MHz crystal source Onboard +5V Voltage regulator Four mounting holes of 3.2 mm each PCB dimensions 77 mm x 82 mm
PIC16F 18-pin Development Board will help you with your prototyping requirement with any of Microchip's 18 pin of 16F PIC microcontrollers.
All ports terminating in separate box
C050
DC supply connection to the board Jumper selectable 20 MHz crystal source Onboard +5V Voltage regulator Four mounting holes of 3.2 mm each PCB dimensions 56 mm x 55 mm
4 Digit 7-Segment Display using 74HC595 (R) kit drives four 7-Segment common cathode display using Serial Shift Register IC.
Four 0.5" common cathode display Input / Output Box type connector for
C051
6 Digit 7-Segment Multiplexed Display (R) kit offers 6 digit common anode/cathode multiplex display.
0.5" 7-segment display (Common anode or
Common cathode)
Multiplex style connection of the 7-
of the segment
C052
RS232 or RS485 Board will help you provide a seamless connection of either of the protocol RS232 or RS485 with your interfacing circuit.
5 VDC Supply sourced through the Box
RS485 link cable and 9 pin female type D connector for interfacing of UART signals to the PC Four mounting holes of 3.2 mm each PCB dimensions 38 mm x 61 mm
sales@anykits.com
12
www.anykits.com
MICROCONTROLLER/INTERFACE
RTC ADD-ON BOARD C053 4 SERVO CONTROLLER BOARD C054
RTC Add-On Board offers an easy way to interface a standard I2C RTC IC type DS1307, into your project.
5 VDC supply sourced through the
Our 4 Servo Controller Board is a solution for controlling upto 4 Servos via onboard preset or potentiometer.
Microcontroller based design for greater
interfacing Box Header connector Battery backup for the RTC board available on the PCB Four mounting holes of 3.2 mm each PCB dimensions 50 mm x 33 mm
C055
input power supply Berg connector for connection of Servos Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 57 mm x 65 mm
Unipolar 4-Phase Stepper Motor Controller Board will help you control a Stepper Motor or 4 individual Solenoids.
Box Header connector provides for easy
C056
interfacing option
Separate LED indicator for individual Phase Power Battery Terminal (PBT) for easy
PIC18F USB Development Board will help you with your prototyping requirement with any 28/40-pin Microchip supporting USB interface microcontrollers.
All ports terminating in separate Box
C057
8 Servo Adapter Board is a small board which offers connection interface to upto 8 servo's via a standard Box Header connector.
Power supply for the servos is sourced via
DC supply connection to the board 20 MHz crystal source Onboard +5V Voltage regulator Four mounting holes of 3.2 mm each PCB dimensions 77 mm x 87 mm
separate onboard PBT connector with LED indicator Well marked Berg connector for connecting servos Four mounting holes of 3.2 mm each PCB dimensions 60 mm x 25 mm
sales@anykits.com
13
www.anykits.com
AA/AAA Battery Voltage Tester is a simple, easy and cheap kit to test and visualize the voltage of AA and AAA type batteries commonly available in the market. This kit is based on the famous LM3914 IC from National Semiconductor.
Input - 5 VDC Output - 10 LED's 2 Types of display - Bar and Dot selectable
0 - 10V LED Voltmeter kit is an easy and cheap kit to instantly visualize signal level. This kit is based on the famous LM3914 IC from National Semiconductor.
Input - 12 VDC @ 100 mA Output - 10 LED's 2 Types of display - Bar and Dot selectable
by a jumper
Very low current consumption, typical
by a jumper Very low current consumption, typical 100 mA Berg pins for connecting power and voltage in Four mounting holes of 3.2 mm each PCB dimensions 34 mm x 74 mm
100mA
Berg pins for connection of power and
voltage in
Four mounting holes of 3.2 mm each PCB dimensions 31 mm x 74 mm
D003
D005
Variable Range LED Voltmeter kit is a simple and cheap way of visually displaying voltage of a given source with the help of 10 LED's. This kit is based on the famous LM3914 IC from National Semiconductor.
Input - 12 VDC @ 190 mA Range - 0 - 1.3 V and 0 - 10.8 V
12V Lead Acid Battery Monitor is a simple kit which tells you the voltage of your Lead Acid battery visually with the help of 10 LED's. This kit is based on the famous LM3914 IC from National Semiconductor.
Input - 15 VDC Max Maximum and Minimum range selectable
by a jumper Very low current consumption, typical 100 mA Berg pins for connecting power and voltage in Four mounting holes of 3.2 mm each PCB dimensions 32 mm x 74 mm
by a jumper
Very low current consumption, typical
100 mA
Berg pins for connecting power / voltage in Four mounting holes of 3.2 mm each PCB dimensions 37 mm x 75 mm
D007
0 - 20V LED Voltmeter kit displays the voltage of the source using 20 LED's. This kit is based on the famous LM3914 IC from National Semiconductor.
Input - 5 VDC Max @ 30 mA in DOT mode
Current Sense Switch kit is a simple circuit which will operate a relay when a preset current is reached / exceeded. This circuit can offer over current protection to your project. You can connect various alarm output or simply break the supply to the circuit using the relay.
Input - 5 VDC Max @ 30 mA in DOT mode
and 300 mA in BAR mode Range selectable with onboard preset Output - 20 LED's 2 Types of display Bar and Dot selectable by a jumper Berg pins for connecting power / voltage in Four mounting holes of 3.2 mm each PCB dimensions 40 mm x 145 mm
preset
Output - SPDT Relay Power Battery Terminal (PBT) and Terminal
SINEWAVE GENERATOR
D008
PULSE GENERATOR
D009
Sinewave Generator kit will provide you with a Sinusoidal Waveform output to test various instruments. You can also use the High quality output from this kit to insert a tone modulation in your audio and RF equipment. This kit is designed using XR2206 IC to provide High Stability and Accuracy.
Input - 12 VDC Max @ 50 mA Range - Jumper selectable and preset
Pulse Generator kit will generate a frequency in KHz which can form a good test gear project. This kit is based on the classic LM555 timer IC.
Input - 12 VDC Max @ 40 mA Range - jumper selectable and preset
tunable range of 1 Hz to 180 KHz Power-On LED indicator Terminal pins for easy connection Four mounting holes of 3.2 mm each PCB dimensions 40 mm x 47 mm
onboard preset
Power-On LED indicator Power Battery Terminal (PBT) for easy
connection
PCB dimensions 52 mm x 58 mm
sales@anykits.com
14
www.anykits.com
LED Panel Meter kits which accept a single-ended input to display many parameters including voltage, current, temperature, pressure etc.
Supply input 5 VDC, single supply
LUX Meter Module kit has been design to measure the illumination. Illumination is luminas flux falling on surface area of photo diode. This illumination converted to corresponding voltage using Op-Amp circuit.
operation
Maximum range is 0 - 199.9 mV Decimal point position is selectable via
jumper
Berg connector for connecting supply input
and signal in
PCB dimensions 73 mm x 55 mm
Supply 9 VDC PP3 Battery @ 20 mA Onboard Photo Diode Onboard preset for calibration Range selection via jumper Interfacing is via berg connector Power-On LED indicator PCB dimensions 54 mm x 38 mm
sales@anykits.com
15
www.anykits.com
Long Duration Timer kit can be used for all application requiring a delay of upto 2 Hours. This kit is built around digital gates and 4020 IC.
Electronic Toggle Switch kit can be used for switching On/Off application of home appliances like fan, light etc.
Input - 12 VDC Onboard Start Switch Relay output - SPDT relay Relay specification - 5 A @ 250 VAC Relay state LED indicator Range upto 2 Hours, jumper selectable and preset adjustable Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection PCB Mounted ON/OFF slide switch Four mounting holes of 3.2 mm each PCB dimensions 49 mm x 86 mm
Input - 12 VDC Onboard ON/OFF switch Relay output - SPDT relay Relay specification - 5 A @ 250 VAC Relay state LED indicator Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection Terminal pins for supply connection Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 58 mm
E004
Light / Dark Sensitive Switch kit is a simple project which operates a relay when the light falling on the LDR goes below or goes above a set point.
Input - 12 V @ 50 mA Relay output - SPDT relay 2-in-1 kit, either as light sensitive kit or
1 Sec To 100 Sec Timer kit can be used for all application requiring a delay of upto 100 Seconds. This kit is built around the famous 555 timer IC.
Input - 12 VDC @ 100 mA Onboard start and reset tactile switch Relay output - SPDT relay Relay specification - 5 A @ 250 VAC Relay state LED indicator Preset adjustable range function Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 48 mm x 63 mm
dark sensitive switch Onboard preset to set the level Power-On LED indicator Relay On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 50 mm x 54 mm
E006
60 Sec Timer kit can be used in all application requiring a delay of upto 60 Seconds. This is based on the Classic 555 Timer IC.
Classic AC 230 V Timer kit can be used in all application requiring a delay of upto 3 Minutes to operate or control any AC mains load of upto 200 Watts. This is based on the Classic 555 Timer IC, triggering a TRIAC. Input and Output is Optically Isolated.
Input - 12 VDC Output - upto 200 Watts Optically isolated Input / Output Onboard start and reset tactile switch Timer On LED Preset adjustable and jumper selectable for range Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 91 mm
Input - 12 VDC @ 56 mA Onboard start switch Relay output - SPDT relay Relay specification - 5 A @ 250 VAC Relay state LED indicator Preset adjustable range function Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 56 mm
CYCLIC TIMER
E009
E007
Cyclic Timer kit can be used in all applications requiring a cyclic On/Off condition of the relay. This kit is ideal for use in flashing of a light bulb, buzzer or siren application.
Power-ON Delay Switch which can be used in all applications requiring a delay during power-on from 10 seconds onwards.
Input - 12 VDC Relay output - SPDT relay Relay specification - 5 A @ 250 VAC Preset adjustable range function Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 42 mm x 45 mm
Input - 12 VDC Relay output - SPDT relay Relay specification - 5 A @ 250 VAC Relay state LED indicator Preset adjustable range function Power-On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 58 mm
sales@anykits.com
16
www.anykits.com
Light Sensitive Switch is a simple project which operates a relay when the light falling on the LDR goes above a set point.
Input - 12 VDC @ 50 mA Relay output - SPDT relay Onboard preset to set the level Relay On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 51 mm
Dark Sensitive Switch is a simple project which operates a relay when the light falling on the LDR goes below a set point. This circuit is built using CA3140 Op-amp and can also be considered for use in energy saving application.
Input - 12 V @ 50 mA Relay output - SPDT relay Onboard preset to set the level Relay On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 51 mm
Temperature Sensitive Switch is a simple project which operates a relay when the temperature in a particular area goes above a set point. This circuit is built using CA3140 Op-amp and NTC temperature Sensor.
Input - 12 VDC @ 50 mA Range - 30 C to 60 C Relay output - SPDT relay Onboard preset to set the level Relay On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 51 mm x 50 mm
10 Event Programmable Timer Using DS1307 RTC is a versatile alarm kit with battery backup clock circuit. It can set upto 10 alarms to trigger in a day with single or dual output available for interfacing.
Upto 10 settable alarms in a day Dual output available for interfacing. A
E017
Temperature Controller Using PIC MCU is a utility Temperature Controller kit for use with a LM35 based temperature sensor with 2 relay outputs. This is a simple Microcontroller based design using inbuilt ADC to read the temperature sensor connected to it. Two relay outputs trigger either an alarm or control an interface connected to it when either the Low or High set temperature set is reached.
Microcontroller based design for greater
activity of the kit or menu in configuration mode. Two 12V SPDT (Single Pole Double Throw) relay for alarm/control use Individual relay out for Low and High alarm set Simple set/configuration available via 3 tactile switches on the PC EEPROM backup for alarm setting Power and Relay On LED indicator PBT type connector for connecting supply and relay output to the PCB Onboard regulator for regulated supply to the kit Crystal resonator based design for better accuracy IC sockets for the IC's used in the kit Four mounting holes of 3.2 mm each PCB dimensions 69 mm x 91 mm
relay output available for 1 second on trigger and upto 8 selectable high outputs available for further interfacing to the outside world Easy setup of alarm and time via 3 tactile switches available on the PCB Power and Relay On LED indicator Battery backed up clock module 16x2 backlight LCD for easy display of time and status of the working project PBT type connector for connecting supply and relay output to the PCB 12V SPDT (Single Pole Double Throw) relay for alarm use Onboard regulator for regulated supply to the kit Crystal resonator based design for better accuracy AUX PWR (Auxiliary Power) available to supply 5V regulated DC supply to other interfaces connected to this kit IC sockets for the IC's used in the kit Four mounting holes of 3.2 mm each PCB dimensions 94 mm x 61 mm
E015
2 Digit Count Down Timer is a utility Count Down timer kit for upto 99 seconds of countdown time. This kit can find many uses in your shack and home. The relay output remains on during the Count Down period, allowing you to interface load or alarm that you want to keep it on for a certain amount of time (in seconds).
Microcontroller based design for greater
time
12V SPDT (Single Pole Double Throw)
set function
Power and Relay On LED indicator PBT type connector for connecting supply
the kit
Crystal resonator based design for better
accuracy
PCB dimensions 72 mm x 81 mm
sales@anykits.com
17
www.anykits.com
LIGHT EFFECTS
LIGHT DIMMER F001 WHITE LED LAMP F002
Light Dimmer kit is a low cost dimmer circuit for adjusting the light brightness of incandescent, Halogen Lamp, Light Bulb upto 250 W.
White LED Lamp (230 VAC), is a kit which can be used as a Night Lamp in houses working on direct 230 VAC.
Input supply - 230 VAC Output - 4 white LEDs Small size, low current consumption Power Battery Terminal (PBT) for easy input
Input supply - 230 VAC Output - 250 W Triac controlled On board POT for adjusting level Power Battery Terminal (PBT) for easy input / output connection Four mounting holes of 3.2 mm each PCB dimensions 40 mm x 34 mm
F003
STROBE KIT
F004
LED Arrow Chasing Indicator kit can be used to display a light arrow to show direction.
Strobe Kit will help you drive your flash tube for use in your favorite lighting application. Some of the application areas are dynamic effect for disco parties, photographic special effect, to attract attention.
Input supply - 230 VAC Onboard POT to adjust flash frequency Power Battery Terminal (PBT) for easy
Input supply - 9 VDC Output - arrow symbol made with LEDs Battery operated low current consumption Terminal pins for connecting input supply Four mounting holes of 3.2 mm each PCB dimensions 45 mm x 86 mm
input 230 VAC mains and flash tube connection Four mounting holes of 3.2 mm each PCB dimensions 49 mm x 92 mm
4 LED FLASHER
F005
F006
Laser Diode Driver kit will help you safely drive (constant current) a 3 mW visible Laser Diode for your application.
Input supply - 6 VDC Onboard preset to adjust the current flow
18 LED Multiplexed Chaser is a simple and fun loving kit which can be used to attract attention in a area.
Input supply - 9 ~ 12 VDC @ 17 mA
current
6 X 3 LEDs to create a chasing sequence of
10 LED Chaser is a simple kit which can be used to attract attention in an area.
Input supply - 9 ~ 12 VDC @ 20 mA
Current
Onboard preset to adjust the speed of
chaser
2 PCB project PCB dimensions 46 mm x 65 mm
200W Lamp Flasher kit is used to flash lamps, bulbs and halogen lamp to give your product that attracting look.
Input supply - 6 ~ 12 VDC Output - upto 200 W lamp / bulb load Optically isolated Mains supply Onboard preset to adjust the frequency (speed) of flashing (1 Hz to 5 Hz) Power Battery Terminal (PBT) for easy input 230 VAC mains and load connection Terminal pins for connecting DC power supply Four mounting holes of 3.2 mm each PCB dimensions 36 mm x 68 mm
Dark Sensitive Switch kit switches a load connected to it when night falls. It could be used as an automatic street light application.
Input supply - 240 VAC Output - upto 200 W Lamp / Bulb load Small size PCB Power Battery Terminal (PBT) for easy connection of input 230 VAC Mains and Load Four mounting holes of 3.2 mm each PCB dimensions 37 mm x 49 mm
sales@anykits.com
18
www.anykits.com
LIGHT EFFECTS
30 LED CHASER F011 SOLID STATE RELAY SWITCH F012
30 LED Chaser is a simple kit which can be used to attract attention in an area.
Input supply - 9 ~ 15 VDC @ 25 mA
Solid State Relay Switch is a simple kit which will help you control (ON / OFF) a single high power circuit from a low power drive.
Load - 24 to 240 VAC @ 500 W Trigger voltage - 2 to 5 VDC (TTL) @
Current Onboard preset to adjust the speed of chaser 2 PCB project Terminal pins for connecting DC power supply PCB dimensions 46 mm x 63 mm
10 mA
Input isolated with use of Optocoupler Power Battery Terminal (PBT) for easy
signal
Heatsink for TRIAC Four mounting holes of 3.2 mm each PCB dimensions 29 mm x 74 mm
5 Lamp Disco Lights is very similar to our J009 kit with the difference of being able to light bulbs with the use of Triac.
Power supply Input - 6 ~ 12 VDC Output - 240 VAC @ 100 W each Jumper selectable audio source Input / Output isolated with use of Optocoupler Onboard preset to adjust audio level to the IC On board MIC capsule with preamp Terminal pins for connecting DC power supply Power Battery Terminal (PBT) for easy input 230 VAC mains and load connection Four mounting holes of 3.2 mm each PCB dimensions 69 mm x 107 mm
Micro Based Running Light Controller kit will attract attention by way of running light effect using 8 bulbs. An ideal project for use during festival lighting, auspicious occasions at home or social gathering events.
Microcontroller based design for greater
the circuit
Industry standard isolation with the help of
the kit
Diode protection for reverse polarity
sales@anykits.com
19
www.anykits.com
POWER SUPPLY
5V/1A REGULATED POWER SUPPLY G001 5V/3A REGULATED POWER SUPPLY G002
This kit will provide 5 V @ 1 Amp DC Regulated Supply. The kit is based on the famous 7805 voltage regulator in TO220 package.
Input - 7 - 18 VAC/DC Output - 5 V @ 1 A regulated low ripple DC
This kit will provide 5 V @ 3 Amp DC Regulated Supply. The kit is based on the famous 7805 voltage regulator in TO3 package.
Input - 7 - 18 VAC/DC Output - 5 V @ 3 A regulated low ripple DC
voltage
Onboard bridge rectifier to convert AC to
voltage
Heatsink for regulator IC Onboard bridge rectifier to convert AC to
DC
Thermal overload/short circuit protection
DC
LED indication for output Thermal overload/short circuit protection
(provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Filter capacitors for low ripple DC output LED indication for output Four mounting holes of 3.2 mm each PCB dimensions 35 mm x 45 mm
(provided by IC feature)
Power Battery Terminal (PBT) for easy
G003
G004
This kit provides Positive and Negative (Dual Output) 5 V @ 1 A Regulated Power Supply.
Input - 7-0-7 VAC to 15-0-15 VAC Output - Dual output 5 V @ 1 A
This kit provides Positive and Negative (Dual Output) 5V @ 3A regulated Power Supply.
Input - 7-0-7 VAC to 15-0-15 V AC Output - dual output 5 V @ 3 A
regulated low ripple DC voltage Heatsink for regulator ICs Onboard bridge rectifier to convert AC to DC LED indication for both the outputs Thermal overload/short circuit protection (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 60 mm
DC
LED indication for both the outputs Thermal overload/short circuit protection
(provided by IC feature)
Power Battery Terminal (PBT) for easy
G005
G006
This kit provides a variable output power supply ranging from 1.2 to 25 V @ 3 A. Uses industry famous LM317K in TO3 package for delivering variable output voltage.
Input - minimum 30 VAC Output - variable output from 1.2 ~ 25 V
This kit provides a variable output power supply ranging from 1.2 to 30 V @ 5 A. Uses industry famous positive voltage regulator LM338K in TO3 package for delivering variable output voltage.
Input - minimum 35 VAC, 6 Amp Output - variable output from 1.2 ~ 30 V
DC
LED indication at input of IC Thermal overload/short circuit protection
DC
LED indication at input of IC Thermal overload/short circuit protection
(provided by IC feature)
Power Battery Terminal (PBT) for easy
(provided by IC feature)
Power Battery Terminal (PBT) for easy
sales@anykits.com
20
www.anykits.com
POWER SUPPLY
1.2 - 15V/3A ADJUSTABLE REGULATED POWER SUPPLY G007 MINI 7805 REGULATOR G008
This kit provides a variable output power supply ranging from 1.2 to 15 V @ 3 A. It uses Low Dropout Positive Regulator LM1084 in TO220 package for delivering variable output voltage.
Input - 18 VAC/DC Output - variable output from 1.2 ~ 15 V
This kit provides 5 VDC @ 1 A regulated supply. This mini kit is based on the famous 7805 voltage regulator in TO220 package.
Input - 7 to 18 VDC Output - 5 V @ 1 A regulated low ripple DC
voltage
Thermal overload/short circuit protection
@ 3 A Regulated low ripple DC voltage Heatsink for regulator IC On board bridge rectifier to convert AC to DC LED indication at input of IC Zener trimmed band gap reference, current limiting and thermal shutdown (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Onboard PCB mounted Potentiometer (POT) for varying the output voltage Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 58 mm
(provided by IC feature)
Berg connector for connecting input and
output
Filter capacitors for low ripple DC output PCB dimensions 15 mm x 37 mm
G010
This kit is an ideal solution for power supply requirements of your TESLA coil experiments. Onboard oscillator can generate 20 KHz up to 30 KHz frequency required for energizing TESLA coil.
TINY 5V REGULATOR
G009
on coil) This kit provides 5 VDC @ 100 mA regulated supply. This tiny kit is based on the famous 7805 voltage regulator in TO92 package.
Input - 7 to 18 VDC Output - 5 V @ 100 mA regulated low Onboard PRESET to adjust frequency of
oscillator
Diode protection at the output against
ripple DC voltage
Thermal overload/short circuit protection
(provided by IC feature)
Berg connector for connecting input and
output
Filter capacitors for low ripple DC output PCB dimensions 15 mm x 37 mm
G011
G012
This kit provides Positive and Negative (Dual) variable output power supply ranging from 1.2 to 30 V @ 3 A. Uses industry famous LM317K and LM337K in TO3 package for delivering variable output voltage.
Input - minimum 30 VAC Output - dual variable output from 1.2 ~
This kit provides Positive and Negative (Dual) variable output power supply ranging from 1.2 to 25 V @ 1 A. Uses industry famous LM317T and LM337T in TO220 package for delivering variable output voltage.
Input - minimum 30 VAC Output - dual variable output from 1.2 ~
DC
LED indication at input of ICs Thermal overload/short circuit protection
DC
LED indication at input of IC's Thermal overload/short circuit protection
(provided by IC feature)
Power Battery Terminal (PBT) for easy
(provided by IC feature)
Power Battery Terminal (PBT) for easy
sales@anykits.com
21
www.anykits.com
POWER SUPPLY
TINY 1.2 - 30V REGULATED POWER SUPPLY G013 9 VDC POWER SUPPLY G015
This kit provides a variable output power supply ranging from 1.2 to 30 V @ 1.5 A. Uses industry famous LM317 in TO220 package for delivering variable output voltage.
Input - minimum 30 VAC Output - variable output from 1.2 ~ 30 V
Tiny low current 9 VDC Regulated Power Supply for testing the Op-Amp based projects.
Input - 10 to 18 VDC or AC, 200 mA Output - 9 VDC, Zener regulated low ripple
DC voltage
Input bridge rectifier made from discrete
@ 3 A regulated low ripple DC voltage Heatsink for regulator IC Onboard bridge rectifier to convert AC to DC LED indication at input of IC Thermal overload/short circuit protection (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Relimate connector for connecting Potentiometer (POT) to the PCB Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 39 mm x 53 mm
Diodes
LED indication for output Terminal pins for connecting input and
output
Four mounting holes of 3.2 mm each PCB dimensions 29 mm x 44 mm
G017
This kit will source Dual Unregulated Power Supply for your project. Ideal for Audio amplifier, Mixer design etc.
G016
This kit provides Zener Regulated Dual 9 VDC output power supply.
outputs
Power Battery Terminal (PBT) for easy
Diodes
Power Battery Terminal (PBT) for easy
output
Four mounting holes of 3.2 mm each PCB dimensions 96 mm x 56 mm
G019
This kit will source Dual Unregulated Power Supply for your project. Ideal for Audio amplifier, Mixer design etc.
Input - maximum 30-0-30 VAC, 1 Amp Output - maximum dual output 35 VDC
This kit provides a variable output power supply ranging from 2.6 to 24 V @ 2.5 A. It's an ideal add-on to your workbench. Uses the industry famous LM723 in DIP package.
Input - minimum 30 VAC Output - variable output from 2.6 ~ 24 V
from center tap transformer Bridge rectifier made of discrete 1A diodes to convert AC to DC LED indication for both the outputs, helps in fault finding Power Battery Terminal (PBT) for easy input and output connection Filter capacitors for near ripple free DC output Four mounting holes of 3.2 mm each PCB dimensions 43 mm x 69 mm
diodes to Convert AC to DC
LED indication for input Power Battery Terminal (PBT) for easy
output voltage
Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 67 mm x 89 mm
sales@anykits.com
22
www.anykits.com
POWER SUPPLY
VARIABLE AUXILIARY POWER SUPPLY G020 MINI DRILL POWER SUPPLY G021
This kit provides a variable output power supply ranging from 2.6 to 24 V @ 1 A. It's an ideal add-on to your workbench. Uses the industry famous LM723 in DIP package.
Input - minimum 30 VAC Output - variable output from 2.6 ~ 24 V
This kit will control the speed of your hobby drill with changing output voltage. Uses the industry famous LM317 in TO220 package for delivering variable output (Voltage).
diodes to convert AC to DC
LED indication for input Power Battery Terminal (PBT) for easy
output voltage
Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 61 mm x 76 mm
Input - 15 VAC/DC, 1 A Output - upto 12 VDC Heatsink for regulator IC Bridge rectifier made using discrete 1 A diodes LED indication for input Thermal overload/short circuit protection (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Onboard PCB mounted POT for varying the output Voltage Four mounting holes of 3.2 mm each PCB dimensions 39 mm x 74 mm
G022
HALFWAVE RECTIFIER
G023
This kit can be used to power up TTL and CMOS based projects, it provides 5 VDC & 12 VDC @ 1Amp outputs. The kit is based on the industry famous 7800 series voltage regulator in TO220 packages.
Input - 18 VAC/DC Output - 5 V & 12 V @ 1 A regulated low
ripple DC voltage
Onboard Diode Rectifier to convert AC to
input connection
Four mounting holes of 3.2 mm each PCB dimensions 25 mm x 32 mm
DC
Thermal overload/short circuit protection
(provided by IC feature)
Power Battery Terminal (PBT) for easy
G024
Small Full Wave Bridge Rectifier kit, for power supply experiments.
Input - maximum 18 VAC, 1 Amp Output - depends on transformer voltage
input connection
LED indication for output Four mounting holes of 3.2 mm each PCB dimensions 31 mm x 41 mm
input connection
LED indication for output Four mounting holes of 3.2 mm each PCB dimensions 32 mm x 39 mm
G028
G029
This kit is designed to provide unregulated high voltage, high current for your demanding needs. Ideally suited for use in Audio Amplifier design projects.
This kit is designed to provide unregulated high voltage, high current for your demanding needs. Ideally suited for use in Audio Amplifier design projects.
Input - 0 - 75 VAC, 10 Amp Unregulated fused output with extra
Input - 0 - 75 VAC, 10 Amp Unregulated fused output 10 A bridge rectifier on board LED indication for output PCB mounted LUGS for connecting input and output Four mounting holes of 3.2 mm each PCB dimensions 51 mm x 97 mm
filtering
10 A bridge rectifier on board LED indication for output PCB mounted LUGS for connecting input
and output
Four mounting holes of 3.2 mm each PCB dimensions 74 mm x 96 mm
sales@anykits.com
23
www.anykits.com
POWER SUPPLY
DUAL 80V/10A UNREGULATED POWER SUPPLY G030 DUAL 90V/10A UNREGULATED POWER SUPPLY G031
This kit is designed to provide symmetrical output unregulated, high voltage, high current for your demanding needs. Ideally suited for use in Audio Amplifier design projects.
Input - maximum 80 VAC Center-tap, 10 A Symmetrical unregulated, individually
This kit is designed to provide symmetrical output unregulated, high voltage, high current for your demanding needs. Ideally suited for use in Audio Amplifier design projects.
Input - maximum 80 VAC center-tap,
10Amp
Symmetrical unregulated, individually
fused outputs 10A bridge rectifier on board LED indication for both the outputs PCB mounted LUGS for connecting of input and output Four mounting holes of 3.2 mm each PCB Dimensions 114 mm x 84 mm
fused outputs
10A bridge rectifier on board LED indication for both the outputs PCB mounted LUGS for connecting of input
and output
Four mounting holes of 3.2 mm each PCB Dimensions 154 mm x 84 mm
G033
G034
This kit is designed to provide 5 V @ 500 mA DC regulated supply with an onboard mains transformer. This kit is based on the famous 7805 voltage regulator in TO220 package.
Input - 230 VAC Or 110 VAC, Jumper
This kit is designed to provide 12 V @ 700 mA DC regulated supply with an onboard mains transformer. This kit is based on the famous 7812 voltage regulator in TO220 package.
Input - 230 VAC Or 110 VAC, Jumper
setting for 110 VAC Output - 5 V @ 500 mA regulated low ripple DC voltage Thermal overload/short circuit protection (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection External On/Off switch connection possible LED indication for output Four mounting holes of 3.2 mm each PCB Dimensions 72 mm x 40 mm
ripple DC voltage
External On/Off switch connection possible Thermal overload/short circuit protection
(provided by IC feature)
Power Battery Terminal (PBT) for easy
G035
This kit can be used to power up TTL and CMOS based projects, it provides 5 VDC & 12 VDC outputs with an onboard mains transformer. The kit is based on the industry famous 7800 series voltage regulator in TO220 packages.
Input - 230 VAC Or 110 VAC, Jumper
regulated low ripple DC voltage Thermal overload/short circuit protection (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection External On/Off switch connection possible LED indication for outputs Four mounting holes of 3.2 mm each PCB dimensions 87 mm x 49 mm
G037
This kit, used to provide 15 VAC @ 1A, is ideal for powering many anykits projects.
Input - 230 VAC Or 110 VAC, Jumper
sales@anykits.com
24
www.anykits.com
REMOTE CONTROL
8 CHANNEL INFRARED REMOTE H001 4 CHANNEL INFRARED REMOTE H002
8 Channel Infrared (IR) Remote kit is a simple remote control kit which you can connect to various existing projects. You can also interface this kit to our Eight Channel Relay Board (I007).
Supply - Transmitter : 2.4 ~ 6 VDC, 5 V @
4 Channel Infrared (IR) Remote is a simple kit using the famous HT12A and HT12D encoder / decoder chips from Holtek. You can also interface this kit to our Four Channel Relay Board (I006).
Supply - Transmitter : 2.4 ~ 5 VDC, 5 V @
150 mA & Receiver : 9 ~ 12 VDC, 12 V @ 25 mA Output - 2 Latched, 6 Momentary TTL compatible outputs Crystal based oscillator for reliability of operation Crystal based design improves the oscillator's frequency stability Jumper selectable custom codes to operate more than one unit in the same area LED output to indicate transmission status High noise immunity Terminal pins for easy connecting power supply Berg connector for interfacing of receiver board Four mounting holes of 3.2 mm each PCB dimensions - Transmitter : 37 mm x 82 mm & Receiver : 54 mm x 56 mm
20 mA & Receiver : 9 ~ 12 VDC, 12 V @ 40 mA Output - 4 Latched TTL compatible output Crystal based oscillator for reliability of operation DIP switch selectable 8 bit address code LED output to indicate reception ON/OFF slide switch in the transmitter Power-On LED indicator in the Receiver / Transmitter High noise immunity Berg connector for interfacing of the board Four mounting holes of 3.2 mm each PCB dimensions - Transmitter : 61 mm x 47 mm & Receiver : 46 mm x 46 mm
H005
8 Channel RF Remote kit is a simple remote control kit which you can connect to various existing projects. You can also interface this kit to our Eight Channel Relay Board (I007).
Supply - Transmitter : 2.4 ~ 6 VDC, 5 V @
RF Based DC Motor Direction Controller kit provides an easy way to control the direction of your DC Motor connected to the receiver. This kit uses the famous HT12E and HT12D encoder / decoder chips from Holtek. With jumper selectable address on the receiver and transmitter we can control upto 255 more motors in one area without interference with one remote. ideal for mechatronics applications.
Supply - Transmitter : 2.4 ~ 5 VDC, 5 V @
20 mA & Receiver : 5 VDC @ 31 mA without Motor Motor - 1.5 to 5 VDC @ 500 mA Upto 30 meters range (Indoor) DIP switch selectable 8 bit address code LED output to indicate reception ON/OFF slide switch in the transmitter Power-On LED indicator in the Receiver / Transmitter High noise immunity Power Battery Terminal (PBT) and Terminal pins for easy input / output connection Four mounting holes of 3.2 mm each PCB dimensions - Transmitter : 60 mm x 37 mm & Receiver : 60 mm x 58 mm
150 mA & Receive : 9 ~ 12 VDC, 12 V @ 25 mA Output - 2 Latched, 6 Momentary TTL compatible output Crystal based oscillator for reliability of operation Jumper selectable custom codes to operate more than one unit in the same area LED output to indicate transmission status High noise immunity Terminal pins for easy connecting power supply Berg connector for interfacing of receiver board Four mounting holes of 3.2 mm each PCB dimensions - Transmitter : 35 mm x 74 mm & Receiver : 47 mm x 37 mm
sales@anykits.com
25
www.anykits.com
BUILDING BLOCKS
SINGLE CHANNEL RELAY BOARD I004 DUAL CHANNEL RELAY BOARD I005
Single Channel Relay Board is a simple and convenient way to interface a relay for switching application in your project.
Dual Channel Relay Board is a simple and convenient way to interface 2 relays for switching application in your project.
Input - 12 VDC @ 42 mA Output - SPDT relay Relay specification - 5 A @ 230 VAC Trigger level - 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED indicates relay status Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 27 mm x 69 mm
Input - 12 VDC @ 84 mA Output - two SPDT relay Relay specification - 5 A @ 230 VAC Trigger level - 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 49 mm x 68 mm
I006
I007
Quad Channel Relay Board is a simple and convenient way to interface 4 relays for switching application in your project.
8 Channel Relay Board is a simple and convenient way to interface 8 relays for switching application in your project.
Input - 12 VDC @ 169 mA Output - four SPDT relay Relay specification - 5 A @ 230 VAC Trigger level - 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Power Battery Terminal (PBT) for easy relay output and aux power connection Four mounting holes of 3.2 mm each PCB dimensions 88 mm x 68 mm
Input - 12 VDC @ 336 mA Output - eight SPDT relay Relay specification - 5 A @ 230 VAC Trigger level - 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Power Battery Terminal (PBT) for easy relay output and aux power connection Four mounting holes of 3.2 mm each PCB dimensions 169 mm x 72 mm
I026
I032
Opto-isolated 4-Channel Triac Board is used for fast switching applications. Ideal for switching mains circuits, lights, appliances and small loads. Each circuit is effectively isolated with opto-isolators on each channel, TTL inputs control each channel.
Trigger input - 5 VDC, individual cathode
Opto-isolated 8-Channel Triac Board is used for fast switching applications. Ideal for switching mains circuits, lights, appliances and small loads. Each circuit is effectively isolated with opto-isolators on each channel, TTL inputs control each channel.
Trigger input - 5 VDC, individual cathode
and anode out Input supply - 230 VAC Output - 1 A @ 230 VAC Berg pins for connection of control signal Snubber circuit for inductive load switching Power Battery Terminal (PBT) for easy TRIAC output connection Four mounting holes of 3.2 mm each PCB dimensions 77 mm x 149 mm
and anode out Input supply - 230 VAC Output - 1 A @ 230 VAC Berg pins for connection of control signal Power Battery Terminal (PBT) for easy TRIAC output connection Four mounting holes of 3.2 mm each PCB dimensions 80 mm x 174 mm
I034
I035
Opto-Isolated 4-Channel Triac Board (R) is used for fast switching applications. Ideal for switching mains circuits, lights, appliances and small loads. Each circuit is effectively isolated with opto-isolators on each channel, TTL inputs control each channel.
Trigger input - 5 VDC, individual cathode
4-Channel Relay Board-1 is a simple and convenient way to interface 4 relays for switching application in your project.
and anode out Input supply - 230 VAC Output - 1 A @ 230 VAC Snubber circuit for inductive load switching Jumper setting for cathode to common ground Box Header connector for connection of control signal Power Battery Terminal (PBT) for easy TRIAC output connection Four mounting holes of 3.2 mm each PCB dimensions 139 mm x 73 mm
Input - 12 VDC @ 360 mA Output - Four SPDT Relay Relay specification - 10 A @ 230 VAC Trigger level - 2 ~ 5 VDC Box Header connector for connection of trigger signal LED on each channel indicates relay status Power-On LED indicator Power Battery Terminal (PBT) for easy relay output and power in connection Four mounting holes of 3.2 mm each PCB dimensions 65 mm x 116 mm
sales@anykits.com
26
www.anykits.com
BUILDING BLOCKS
4-CHANNEL RELAY BOARD - 2 I036
4-Channel Relay Board-2 is a simple and convenient way to interface 4 relays for switching application in your project.
Input - 12 VDC @ 170 mA Output - Four SPDT Relay Relay specification - 5 A @ 230 VAC Trigger level - 2 ~ 5 VDC Box Header connector for connection of trigger signal LED on each channel indicates relay status Power-On LED indicator Power Battery Terminal (PBT) for easy relay output and power in connection Four mounting holes of 3.2 mm each PCB dimensions 56 mm x 83 mm
sales@anykits.com
27
www.anykits.com
MINI KITS
DARK SENSITIVE SWITCH J001 LIGHT SENSITIVE SWITCH J002
Dark Sensitive Switch is a simple project which operates a relay when the light falling on the LDR goes below a set point.
Light Sensitive Switch is a simple project which operates a relay when light falls on the LDR.
Input - 12 V @ 55 mA Relay output - NC-C-NO Onboard preset to set the level Power-On LED indicator Relay On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 49 mm
Input - 12 V @ 55 mA Relay output - NC-C-NO Onboard preset to set the level Power-On LED indicator Relay On LED indicator Power Battery Terminal (PBT) for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 49 mm
LED FLASHER
J003
J004
LED Flasher is a simple kit producing a flashing effect of six LED's. This kit can be used in all areas where you want to draw attention. Hi-glow LED's providing enough flashing light to attract your attention.
Input - 12 V @ 35 mA Onboard preset to adjust flash rate Terminal pins for connecting power supply Four mounting holes of 3.2 mm each PCB dimensions 53 mm x 35 mm
J005
TONE GENERATOR
J006
Input - 6 VDC Onboard slide switch to select siren sound Terminal pins for connecting power supply Four mounting holes of 3.2 mm each PCB dimensions 42 mm x 42 mm
Tone Generator is a simple kit which generates an Oscillating Frequency to drive a PIEZO disc to produce tones.
Input - 6 VDC @ 30 mA Output Frequency Range - 800 Hz to
7.5 KHz
Onboard preset to change Frequency /
Tone sound
J007
Terminal pins for connecting power supply Four mounting holes of 3.2 mm each PCB dimensions 35 mm x 38 mm
Battery Operated Door Bell kit can be used at home as a Door Bell. This is based on AP6201 IC.
Input - 5 VDC @ 20 mA 4 - different switches for 4 - different type
J008
being played
Terminal pins for connecting power supply Four mounting holes of 3.2 mm each PCB dimensions 51 mm x 42 mm
J009
J010
Audio Dancing LED kit is a fun filled project which generates a LED dancing sequence depending on the audio it senses. This kit is based on one of the VU Meter IC's available.
Power supply input - 6 ~ 9 VDC Output - 5 LED's Onboard preset to adjust audio level to the
IC Onboard MIC capsule with Preamp Terminal pins for connecting power supply Four mounting holes of 3.2 mm each PCB dimensions 39 mm x 67 mm
sales@anykits.com
28
www.anykits.com
MINI KITS
WATER LEVEL ALARM J012 MELODY GENERATOR
Melody Generator kit plays a single melody as soon as power 3 VDC (2AAA Battery) is applied to it. It is built around BT66T melody Generator IC. PCB dimensions 30 mm x 23 mm.
J013
Water Level Alarm kit sounds an alarm when water reaches its sensor. This kit is a simple and a cost effective kit for use in home or industry.
Power Supply Input - 6 VDC @ 25 mA Output - Buzzer Onboard On/Off Switch Sensor PCB included Terminal pins for connecting power supply Four mounting holes of 3.2 mm each PCB dimensions 63 mm x 42 mm
8 LED FLASHER
8 LED Flasher kit simply flashes a set of 8 LED's to give you that reason to attract attention. Power Supply - 9 V (PP3). PCB dimensions 36 mm x 43 mm.
J015
6 LED FLASHER
6 LED Flasher kit simply flashes a set of 6 LED's to give you that reason to attract attention. Power Supply - 9 V (PP3). PCB dimensions 27 mm x 47 mm.
J014
J016
Who's First (Game) Indicator kit simply shows corresponding LED's for whoever pushed the switch first.
Upto four players can play simultaneously Well marked switches Each indication made of four LED's Reset switch overrides all inputs PCB dimensions 95 mm x 52 mm
sales@anykits.com
29
www.anykits.com
MISCELLANEOUS
PROTOTYPE BOARD K001 PROTOTYPE BOARD K002
High quality prototyping board for building and testing circuit solution.
High quality prototyping board for building and testing circuits solution.
Identifiable holes and tracks Easy IC placement Tracks both the ends for supply Board Size 168 mm x 56 mm
Identifiable holes and tracks Easy IC placement Tracks both the ends for supply Board Size 89 mm x 56 mm
PROTOTYPE BOARD
K003
K004
High quality prototyping board for building and testing microcontroller and computer interface circuits.
Identifiable holes and tracks Easy IC placement Tracks both the ends for supply One 25-Pin D Type Male/Female Connector mounting One 9-Pin D Type Male/Female Connector mounting Four 10-Pin Box header Connector mounting Board Size 168 mm x 100 mm
High quality small size general board for experiments, board with individual copper per hole for quick fabrication and testing.
Board size 43 mm x 56 mm 0.1 hole spacing Matrix 15 x 21
K005
K006
High quality small general stripe board for experiments, for quick fabrication and testing.
Board size 43 mm x 56 mm 0.1 hole spacing Matrix 15 X 21
High quality medium size general board for experiments, board with individual copper per hole for quick fabrication and testing.
Board size 86 mm x 56 mm 0.1 hole spacing Matrix 32 X 21
K007
K008
High quality medium size general stripe board for experiments, for quick fabrication and testing.
Board size 86 mm x 56 mm 0.1 hole spacing Matrix 32 X 21
High quality large size general board for experiments, board with individual copper per hole for quick fabrication and testing.
Board size 86 mm x 111 mm 0.1 hole spacing Matrix 32 X 43
K009
K010
High quality large size general stripe board for experiments, for quick fabrication and testing.
Board size 86 mm x 111 mm 0.1 hole spacing Matrix 32 X 43
High quality extra large size general board for experiments, board with individual copper per hole for quick fabrication and testing.
Board size 86 mm x 169 mm 0.1 hole spacing Matrix 32 X 65
sales@anykits.com
30
www.anykits.com
MISCELLANEOUS
GENERAL PURPOSE EXTRA LARGE STRIPE BOARD K011 LCD DIGITAL PANEL METER K012
High quality extra large size general stripe board for experiments, for quick fabrication and testing.
Board size 86 mm x 169 mm 0.1 hole spacing Matrix 32 X 65
LCD Digital Panel Meter for measuring can be used as Voltmeter, Ammeter etc.
Power supply input - 5 VDC @ 25 mA Terminal pins for connecting power supply Berg pins for voltage input
K014
LED Digital Panel Meter for measuring can be used as Voltmeter, Ammeter etc.
Power supply input - 5 VDC @ 150 mA Terminal pins for connecting power supply Berg pins for voltage input
Power supply input - 5 VDC Frequency 914.5 MHz ISM band Range outdoor upto 60 meter, indoor upto 20 meter
ASK RF MODULES
ASK RF Modules Transmitter & Receiver.
K015
Power supply input - 5 VDC Frequency 434 MHz ISM band Range outdoor upto 60 meter, indoor upto 20 meter
sales@anykits.com
31
www.anykits.com
MOTOR/MOTION CONTROL
BIPOLAR STEPPER MOTOR DRIVER M001 DC SERVO MOTOR DRIVER M002
This kit is designed to drive two-phase stepper motor in bipolar mode. It is based on MC3479 IC.
Input - 12 VDC (7.5 to 16 V supply
DC Servo Motor Driver kit, designed using MC33030 IC, is the fastest and low cost way of getting your DC Servo Motor up and running.
Input - 12 VDC Output - can drive upto 1 A Load Overcurrent shutdown, overvoltage
possible) Two-phase stepper motor in bipolar mode with up to 350 mA to each of the two coils Jumper selectable half or full step Adjustable speed with the help of onboard preset Direction control with help of a on board Slide switch Power-On LED indicator Power Battery Terminal (PBT) for easy input (PWR) / output (Motor) connection Four mounting holes of 3.2 mm each PCB dimensions 51 mm x 62 mm
shutdown Programmable reference input Power-On LED indicator Relimate connector for interfacing the kit Four mounting holes of 3.2 mm each PCB dimensions 45 mm x 54 mm
0 TO 5V SERVO DRIVER
M004
0 to 5V Servo Driver kit will control a DC Servo Motor using a varying voltage input of 0 to 5 VDC.
M003
The 555 Stepper Pulse Generator kit will help you with the pulse required to drive your favorite DC Servo Motor application. This kit uses the famous 555 timer IC for generating the Stepping Pulse.
Input - 5 - 12 VDC @ 25 mA TTL/CMOS interfaceable Jumper selectable two speed operation Onboard preset to vary the duty cycle Power-On LED indicator Terminal pins for easy interfacing of the kit Four mounting holes of 3.2 mm each PCB dimensions 39 mm x 37 mm
Input supply - 6 VDC 90 movement 0 to 5 VDC as controlling input for servo Power-On LED indicator Berg connector for easy interfacing of the kit Four mounting holes of 3.2 mm each PCB dimensions 33 mm x 49 mm
M006
Single Motor L298 H-Bridge Control kit will provide DC Motor control for your application. This kit uses the famous industry standard L298 HBridge IC.
M005
555 DC Motor Speed Controller kit will control the speed of a DC motor connected to it. This kit is built using the famous 555 timer IC.
Input supply - 12 VDC Output drive upto 800 mA Onboard preset to vary Duty Cycle from
10% to 95% @ 120 Hz Ideal for mini drill and robotics application MOSFET based output drive with heatsink Diode protection for motor surge Power-On LED indicator Power Battery Terminal (PBT) for easy input (PWR) / output (Motor) connection Four mounting holes of 3.2 mm each PCB dimensions 47 mm x 56 mm
level Output DC drive to Motor - upto 2 A Current Sense Output available Onboard resistor provided for current limit Enable and direction control pins available External diode bridge provided for output Heatsink for IC Power-On LED indicator Power Battery Terminal (PBT) for easy input (PWR) / output (Motor) connection Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 63 mm
M007
M009
Dual Motor L298 H-Bridge Control kit can control two DC motors connected to it. This kit uses the famous industry standard L298 H-Bridge IC.
Motor supply - 7 to 46 VDC Control Logic Supply - Standard TTL logic
Unipolar Stepper Motor Driver kit provides speed, direction and step size control, of a stepper motor connected to it. This kit is based on the famous UCN5804 Stepper Motor driver IC.
Input supply - 7 - 18 VDC Output - upto 1 A per phase Standalone Controller Board Onboard preset for speed adjust Onboard slide switch for direction, step and phase control Power-On LED indicator Power Battery Terminal (PBT) for easy input (PWR) / output (Motor) connection PCB dimensions 52 mm x 79 mm
level Output DC drive to motor - upto 2 A each Current Sense Output available Onboard resistor provided for current limit Enable and direction control pins available External diode bridge provided for output Heatsink for IC Power-On LED indicator Power Battery Terminal (PBT) for easy input (PWR) / output (Motor) connection Four mounting holes of 3.2 mm each PCB dimensions 61 mm x 63 mm
sales@anykits.com
32
www.anykits.com
MOTOR/MOTION CONTROL
MOTOR SPEED & DIRECTION CONTROLLER M008 LIGHT SENSITIVE INDUCTIVE LOAD CONTROLLER M010
Motor Speed & Direction Controller kit offers versatile control of speed and direction for DC motor connected to it. This kit uses the famous LMD18200 for Motor Drive and SG3525 to obtain PWM signal for precise control.
Motor supply - 12 to 55 VDC @ 3 A Max Kit supply - 12 VDC @ 30 mA PWM Output - duty cycle of 0% to 100% @
Light Sensitive Inductive Load Controller kit offers On / Off control, depending on presence or absence of light. Some of the controllable inductive load could be single phase AC Motor, Solenoid Valve etc.
3 KHz Standalone Controller Board Onboard POT for speed adjust Onboard preset for frequency adjust Onboard slide switch for direction control Heatsink for motor drive IC Power-On LED indicator Separate supply connector for motor and control section Power Battery Terminal (PBT) for easy input (PWR) / output (Motor) connection Four mounting holes of 3.2 mm each PCB dimensions 53 mm x 63 mm
Input supply - 12 VDC Output - upto 200 W, 230 VAC Opto-isolated Triac based design Power-On LED indicator Power Battery Terminal (PBT) and Terminal pins for easy input / output connection PCB dimensions 41 mm x 82 mm
M012
ON/OFF DC Motor Controller kit offers simple On/Off Switch Control. Input supply - 12 VDC @ 1 A Output - upto 1 A Onboard tactile switch for ON/OFF control MOSFET based drive design with diode protection LED indicator for ON/OFF state Power-On LED indicator Terminal pins and Power Battery Terminal (PBT) for easy input / output connection PCB dimensions 40 mm x 62 mm
M011
ON/OFF AC Motor Controller kit offers simple On/Off Switch Control. Input supply - 12 VDC @ 40 mA Output - upto 300 W - 230 VAC Onboard tactile switch for ON/OFF control Opto-isolated Triac based design Power-On LED indicator Power Battery Terminal (PBT) and Terminal pins for easy input / output connection Four mounting holes of 3.2 mm each PCB dimensions 44 mm x 86 mm
M015
AC Solid state Relay kit offers simple On/Off type Switch Control with TTL compatible input signal.
M013
DC Motor Direction Control kit offers direction control using digital logic gates and a DPDT relay.
Input signal - 2 ~ 5 VDC, TTL compatible Output - upto 500 W, 230 VAC Optically isolated Triac based design Power Battery Terminal (PBT) and Terminal pins for easy input / output connection Four mounting holes of 3.2 mm each PCB dimensions 35 mm x 72 mm
Input supply - 12 VDC @ 75 mA Output - upto 5 A @ 30 VDC Onboard tactile switch for direction control Relay based drive design with diode protection LED indicator for direction indication Power-On LED indicator Terminal pins and Power Battery Terminal (PBT) for easy input / output connection Four mounting holes of 3.2 mm each PCB dimensions 41 mm x 81 mm
M017
L293 H-Bridge DC Motor Controller kit is a simple board to control motors upto 1 A load.
Motor supply - upto 36 VDC Control logic supply - Standard TTL /CMOS
M016
AC Motor Speed Controller kit is a simple POT based speed controller design for inductive type load.
logic level Output DC drive to motor - upto 1 A Direction control pins available Jumper selectable enable pin External diode bridge provided for output Power-On LED indicator for both supplies Relimate Connector for easy connection of input (PWR) / output (Motor) PCB dimensions 40 mm x 50 mm
Input - 230 VAC Output - upto 500 W - 230 VAC Triac based design Power Battery Terminal (PBT) easy connection Four mounting holes of 3.2 mm each PCB dimensions 50 mm x 47 mm
sales@anykits.com
33
www.anykits.com
MOTOR/MOTION CONTROL
0 - 5V SERVO CONTROLLER M018 JOYSTICK MOTOR CONTROLLER M020
0 - 5V Servo Controller kit will control a hobby type servo motor connected to it via a preset or external DC source. This kit will be ideal add on in animatronics and motion control application.
Microcontroller based design for greater
Joystick Motor Controller kit control a hobby type servo motor connected to it via a joystick type (resistive) sensor connector. This kit will be ideal add-on to animatronics and motion control application.
Microcontroller based design for greater
flexibility and ease of control Single Servo control via clearly marked Relimate Connector Clearly marked jumper to select signal source to control the Servo Onboard preset for ready to control option for this kit Power-on LED indicator Diode protection for reverse polarity connection of DC supply to the PCB Four mounting holes of 3.2 mm each PCB dimensions 32 mm x 47 mm
Relimate Connector
Onboard voltage regulator to provide
interface with any microcontroller development boards External or internal voltage reference option via jumper Onboard preset for current adjustment High speed switching diodes for transistor protection Power-On LED indicator for both the supplies Power Battery Terminal (PBT) for easy supplies and motor connection Heat sink included Four mounting holes 3.2 mm each PCB dimensions 110 mm x 53 mm
interface with any microcontroller development boards External or internal voltage reference option via jumper Onboard preset for current adjustment High speed switching diodes for L298 IC protection Power-On LED indicator for both the supplies Power Battery Terminal (PBT) for easy supplies and motor connection Heat sink included Four mounting holes 3.2 mm each PCB dimensions 74 mm x 71 mm
sales@anykits.com
34
www.anykits.com
2, KRISHNA KUNJ MAIN AVENUE, SANTACRUZ (WEST) MUMBAI 400 054. INDIA PHONE +91 22 32928210
Your kit distributor
www.anykits.com sales@anykits.com
ak-dc.07.08